CQube MF & LF
USER MANUAL
UM_EN
Part No.: 1730095_03
http://torgoborud.com.ua/Professionalnye-kofemashiny.html
CONTENT
CQube MF & LF
CONTENT......................................................................................................................................................... 2
GENERAL............................................................................................................................................................ 4
Introduction...............................................................................................................................................................4
Warnings.....................................................................................................................................................................4
Precautions.................................................................................................................................................................4
Intended use...............................................................................................................................................................4
Facts & weight ..........................................................................................................................................................5
OVERVIEW OF COMPONENTS......................................................................................................... 6
Front of CQube MF13 & MF04.............................................................................................................................6
Interior CQube MF13..............................................................................................................................................7
Interior CQube MF04..............................................................................................................................................8
Front of CQube LF13 & LF04................................................................................................................................9
Interior of CQube LF13....................................................................................................................................... 10
Interior of CQube LF04....................................................................................................................................... 11
Membrane switch navigation............................................................................................................................... 12
Touchscreen navigation......................................................................................................................................... 13
User card................................................................................................................................................................. 14
INSTALLATION AND START-UP...................................................................................................... 15
Start-up procedure for CQube ML & MF........................................................................................................ 15
Fill ingredient canister and bean hopper.......................................................................................................... 17
OPERATION.................................................................................................................................................. 18
Brewing a cup of coffee (CQube with membrane switch)........................................................................... 18
Brewing a cup of coffee (CQube with touchscreen)..................................................................................... 19
Brewing coffee in a jug (CQube with membrane switch)............................................................................. 20
Brewing coffee in a jug (CQube with touchscreen)....................................................................................... 21
CLEANING PROGRAM.......................................................................................................................... 22
Automatic rinsing of the mixing bowl............................................................................................................... 22
Automatic cleaning of dispenser valves............................................................................................................ 23
Automatic cleaning of brewing mechanism...................................................................................................... 24
Open brewer function.......................................................................................................................................... 25
CLEANING AND CARE......................................................................................................................... 26
Disassemble the brewing chamber.................................................................................................................... 26
Disassemble and cleaning of coffee filter.......................................................................................................... 27
Weekly cleaning...................................................................................................................................................... 28
Disassemble mixing system................................................................................................................................. 28
2
CONTENT
CQube MF & LF
Wash these parts .................................................................................................................................................. 29
Reassemble mixing system ................................................................................................................................ 29
Exterior cleaning ................................................................................................................................................... 30
MESSAGE SHOWN ON DISPLAY.................................................................................................. 31
PROGRAMMING ....................................................................................................................................... 32
Activate programming with the user card ...................................................................................................... 32
Jug beverage............................................................................................................................................................ 33
Clean machine ....................................................................................................................................................... 34
Counters ................................................................................................................................................................. 35
DIMENSION SKETCH............................................................................................................................. 37
CQube MF13 & MF04.......................................................................................................................................... 37
CQube LF13 & LF04 ............................................................................................................................................ 38
Some important information may appear in textboxes seen below
IMPORTANT!
INFO.
CAUTION!
More INFO.
Note
INFO.
INFO.
3
GENERAL
CQube MF & LF
Introduction
Thank you for choosing a CQube MF & LF fresh-brew vending machine.
We hope you enjoy it !
Read the user guide before using the machine.
This guide contains important instructions for
proper and safe use of the vending machine.
Always
keep this guide close at hand for future
reference.
Warnings
Never
immerse the machine, plug or mains
cable in water because there is a danger of
electric shock.
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning the use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure they
do not play with the appliance.
not use the machine if the mains cable, plug
Do
is damaged or the machine has fallen down.
If the mains cable is damaged it must be
replaced by the manufacturer, service agent or
similarly qualified persons in order to avoid a
hazard.
Only plug the machine into a properly installed
earthed safety socket whose line voltage
matches the technical data for the machine.
Precautions
not use the machine outdoors so it can be
Do
exposed to weather (rain, snow, frost). It will
cause material damage to the machine.
Do not try to open the machine or repair it in
any way. To avoid danger only have the machine
repaired in a technical workshop, Service
Centre or by a qualified person.
Remove the mains cable from the socket when
the machine is not in use for longer periods. To
do this, pull the plug not the cable.
This appliance must be placed in a horizontal
position which is resistant to any water that
may leak.
Place the machine out of the reach of children.
Position the mains cable so that people cannot
trip over it. Keep it away from sharp edges and
heat sources.
The new hose-sets supplied with this appliance
are to be used, old hose-sets must not be reused.
This appliance is not suitable for installation in
an area where a water jet could be used.
This appliance must not be cleaned by a water
jet.
Intended use
This
appliance is intended to be used in
household and similar applications such as:
- Staff kitchen areas in shops.
- Offices and other commercial working
environments.
- On agricultural estates.
- By clients in hotels, motels and other
residential type environments.
- Bed and breakfast type environments.
4
the optimal performance of the machine
For
these parameters shall not be exceeded:
- Maximum permissible inlet water pressure :
800KPa (8Bar)
- Minimum permissible inlet water pressure:
200KPa (2Bar)
- Maximum working temperature: 40°ºC
- Minimum working temperature: 10°ºC
http://torgoborud.com.ua/Professionalnye-kofemashiny.html
GENERAL
CQube MF & LF
Facts & weight
CQube
MF13
CQube
MF04
CQube
LF13
CQube
LF04
Option
Option
Option
Option
Built-in grinder
Yes
None
Yes
None
Function for selecting jug
Yes
Yes
Yes
Yes
10-12
10-12
10-12
10-12
Ingredient canister
3
4
3
4
Bean hopper
1
None
1
None
Brewing mechanism
Yes
Yes
Yes
Yes
Cleaning function by smart card
Yes
Yes
Yes
Yes
Electronic temperature control
Yes
Yes
Yes
Yes
Adjustable coffee strength
Yes
Yes
Yes
Yes
Illumination of cup during brewing
Yes
Yes
Yes
Yes
Option
Option
Option
Option
Yes
Yes
Yes
Yes
FACTS
Touchscreen
Drink options
Base cabinet: large grounds container
Energy saving mode
Height, Width, Depth
Tank volume
882,427, 550mm
5L
Power supply
995, 420, 565mm
5L
5L
5L
220-230VAC, 50/60Hz, 2200W
Cold water connection
½” External thread
Built-In Cold Water Unit
Option
Option
Option
Option
Co2 Water Unit
Option
Option
Option
Option
Co2 Water Capacity
20 L/Hour
Co2 Water Unit effect
Water purification filter
MODEL/NAME
170W
Option
Option
Option
Option
WEIGHT
CQube MF13
48 kg
CQube MF04
42 kg
CQube LF13
51 kg
CQube LF04
45 kg
Base Cabinet
25 kg
5
http://torgoborud.com.ua/Professionalnye-kofemashiny.html
OVERVIEW OF COMPONENTS
CQube MF & LF
Front of CQube MF13 & MF04
Display
STOP
STOP
Strength Adjustment
Stop Energy Saving Mode
CoffeeC
appuccino
Choco-milk
Small Coffee
Caffè Latte
Hot Water
Espresso
Café Mocca
Café au Lait
Chocolate
Drink Menu
Smart Card Reader
Door Lock
Outlet Hot Drinks
Outlet Water Drinks
Cup Shelf
Drip Grids
Drip Tray
http://torgoborud.com.ua/Professionalnye-kofemashiny.html
Accessories: Base cabinet
6
OVERVIEW OF COMPONENTS
CQube MF & LF
Interior CQube MF13
Bean Hopper
Ingredient Canisters
Grinder
Mixing Bowl
Brewing Mechanism
Drink Outlet
Waste Box
Ingredient canisters of CQube MF13
DETAIL
INGREDIENTS
Hopper
Beans
WIDTH
DEPTH
HEIGHT
CAPACITY
CUPS/UNIT
----
----
----
2.0kg
~180 Cups
Canister
Canister
Espresso
67mm
180mm
250mm
0.44kg
~200 Cups
Chocolate
67mm
180mm
250mm
1.52kg
~80 Cups
Canister
Topping
67mm
180mm
250mm
1.10kg
~120 Cups
7
http://torgoborud.com.ua/Professionalnye-kofemashiny.html
OVERVIEW OF COMPONENTS
CQube MF & LF
Interior CQube MF04
Ingredient Canisters
Coffee Canister
Mixing Bowl
Brewing Mechanism
Drink Outlet
Waste Box
Ingredient canisters of CQube MF04
DETAIL
INGREDIENTS
WIDTH
DEPTH
HEIGHT
CAPACITY
CUPS/UNIT
Canister
Coffee
160mm
180mm
250mm
2.0kg
~180 Cups
Canister
Espresso
67mm
180mm
250mm
0.44kg
~200 Cups
Canister
Chocolate
67mm
180mm
250mm
1.52kg
~80 Cups
Canister
Topping
67mm
180mm
250mm
1.10kg
~120 Cups
8
OVERVIEW OF COMPONENTS
CQube MF & LF
Front of CQube LF13 & LF04
Display
STOP
STOP
Strength Adjustment
Stop Energy Saving Mode
CoffeeC
appuccino
Choco-milk
Small Coffee
Caffè Latte
Hot Water
Espresso
Café Mocca
Café au Lait
Chocolate
Drink Menu
Smart Card Reader
Door Lock
Outlet Hot Drinks
Outlet Water Drinks
Cup Shelf
Drip Grids
Drip Tray
Accessories: Base cabinet
9
OVERVIEW OF COMPONENTS
CQube MF & LF
Interior of CQube LF13
Bean Hopper
Ingredient Canisters
Grinder
Mixing Bowl
Brewing Mechanism
Drink Outlet
Waste Box
Ingredient canisters of CQube LF13
DETAIL
INGREDIENTS
WIDTH
DEPTH
HEIGHT
CAPACITY
CUPS/UNIT
Hopper
Beans
----
----
----
4.0kg
~360 Cups
Canister
Espresso
67mm
180mm
400mm
0.66kg
~300 Cups
Canister
Chocolate
67mm
180mm
400mm
2.66kg
~120 Cups
Canister
Topping
67mm
180mm
400mm
1.95kg
~180 Cups
10
OVERVIEW OF COMPONENTS
CQube MF & LF
Interior of CQube LF04
Ingredient Canisters
Coffee Canister
Mixing Bowl
Brewing Mechanism
Drink Outlet
Waste Box
Ingredient canisters of CQube LF04
DETAIL
INGREDIENTS
WIDTH
DEPTH
HEIGHT
CAPACITY
CUPS/UNIT
Canister
Canister
Coffee
160mm
180mm
400mm
3.50kg
~320 Cups
Espresso
67mm
180mm
400mm
0.66kg
~300 Cups
Canister
Chocolate
67mm
180mm
400mm
2.66kg
~120 Cups
Canister
Topping
67mm
180mm
400mm
1.95kg
~180 Cups
11
OVERVIEW OF COMPONENTS
CQube MF & LF
Membrane switch navigation
Button functions
STOP
CoffeeC
appuccino
Choco-milk
Small Coffee
Caffè Latte
Hot Water
Espresso
Café Mocca
Café au Lait
Chocolate
Press the BACK button if you want to leave the submenu and go back in the
menu.
Press the ENTER button to select a menu function, confirm a set value or a
setting.
Press the MINUS button if you want to decrease a value or go back in the menu.
Press the STOP button if you want to return to the start menu.
To activate energy saving mode press and hold the STOP button for 5 seconds.
Display will show Energy Saving Mode.
You can abort jug process by pressing STOP.
To return to normal mode press and hold the STOP button for 5 seconds while
the machine is in energy saving mode.
Press the PLUS button if you want to increase a value or go forward in the
menu.
ENERGY SAVING MODE
12
The machine decreases the temperature in the water tank to
650C.
OVERVIEW OF COMPONENTS
CQube MF & LF
Touchscreen navigation
Button functions
Choose drink type
by pressing the icon
on the touchscreen,
when an icon is
selected a field in
the bottom of the
screen appears.
Press START to
pruduce your
selected drink.
BACK
Press the BACK button if you want to leave the submenu and go back in the
menu.
ENTER
Press the ENTER button to confirm a set value or a setting. Confirm the new
setting by pressing the E-button.
START
STOP
Press START button to confirm drink choice.
Press the STOP button if you want to return to the start menu.
Press the MINUS button for choosing Strength / Volume of the drink.
Press the PLUS button for choosing Strength / Volume of the drink.
To activate energy saving mode press the power icon on the display.
ENERGY SAVING MODE
The machine decreases the temperature in the water tank to
650C.
13
OVERVIEW OF COMPONENTS
CQube MF & LF
User card
User Card
Is used for entering jug mode and
see counter settings.User card is
supplied by your dealer.
Face
Back
Insert the user card
with the chip upwards
as figure.
For CQube with membrane switch
The display will show the Service Menu, Jug Beverage and you can now
browse forwards through the menu.
Service Menu
Jug Beverage
For CQube with touchscreen
The display will show the Service Menu, you can now browse forward by
touching these icons.
To use the machine again remove the user smart card and store it in a safe place.
14
INSTALLATION AND START-UP
CQube MF & LF
Start-up procedure for CQube ML & MF
Note
B
If the machine doesn’t have any cold water cabinet only follow
the steps in the colored section below.
Connect the 8mm hoses 3 units. (A) parallel between the top and base cabinets,
from left to right.
A
WATER IN
Note
CARBONATED COLD WATER
WATER
Do not connect the electrical cable from the cold water unit
until the machine has heated up.
Connect the carbon dioxide tube to the gas canister and open the tap, check
that the factory set pressure is c. 3.5bar. May be adjusted +0.5 -1.0 bar. Put the
gas canister in place inside the base cabinet.
A
Connect the mains cable to the machine (B) and insert the plug to a
earthed wall socket (C).
Connect the water to the top cabinet on the machine.
Connect the supplied water hose to the cold water connection using a
½’’ R-connection. When pushing the machine into position make sure
there is no interference to the hose to ensure proper water flow.
If the inlet hose is new, flush the system with water first to remove
copper shavings. These can damage the inlet valve.
The new tube set supplied with the appliance must be used. Old tubes
may not be re-used. Connection to a closable valve is recommended.
Min. water pressure; 2 bar (200kPa).
Max. water pressure: 8 bar (800kPa).
Open the water tap.
Open the door and turn on the power switch. See figure.
Close the door
C
The display indicates
button.
Switch
Low Water Level
Press Enter Key
Press the
/
ENTER
The water tank will now automatically fill with 5 litres of water. The
element will not be powered until the water reaches the level sensor.
Set temperature is 96º Celsius.
Once the water heating is complete “Low temp” text will disappear
from the display. (The display text will start to rotate between these
two screens
FRESHBREWED
FILTER COFFEE
and
SELECT PRODUCT
)
Shut off the machine, continue on next page.
15
INSTALLATION AND START-UP
CQube MF & LF
B
A
Switch
Now connect the electricity cable which comes from the base cabinet into the
electric socket at the machine (B).
Switch on the machine again and wait until the text in the display starts to
rotate.
Note
The fresh-brew machine must be warm before any cold water
can be dispensed.
Take a glass and press the button for cold water until water is dispensed in a
even flow and the pressure pump that is buzzing gives a different calmer sound
(cold water compressor is relatively quite so it should not usually be heard very
much)
Now press the button for carbonated water so the water can mix with the
carbon dioxide, keep the button pressed until you have a even flow of water.
When you release the button the pump will fill up the cooling unit and then turn
off. The machine is now ready for use.
16
INSTALLATION AND START-UP
CQube MF & LF
Fill ingredient canister and bean hopper
Lift the lid and fill the bean hopper with freshly
roasted coffee beans without additives.
01
02
Remove the ingredient canisters to avoid spilling
in the machine and fill with ingredients.
When filling the ingredients, keep the opening of
the canister chute upwards (A).
A
03
B
C
04
05
Open the bean stop (B) on the bean hopper.
The machine is ready to use.
Reassembly canisters.
When placing the ingredient canisters, Ensure that
the openings of the canister chutes point down
toward the mixing bowl (C).
17
OPERATION
CQube MF & LF
Brewing a cup of coffee (CQube with membrane switch)
STOP
CoffeeC
A
appuccino
Choco-milk
Small Coffee
Caffè Latte
Hot Water
Espresso
Café Mocca
Café au Lait
Chocolate
Place a cup under the outlet for hot drinks.(A)
The strength of the drink is set to default. If you would like to increase or
decrease the strength then follow the steps in the section below.
Stronger drink, Press the
button
or
Weaker drink, Press the
button
Select coffee by pressing the coffee button
The display shows:
Please wait...
and the cup light goes on.
Wait until the cup light switches off and the text
Please wait...
has disappeared from the display before removing the cup.
18
OPERATION
CQube MF & LF
Brewing a cup of coffee (CQube with touchscreen)
A
Place a cup under the outlet for hot drinks. (A)
Choose drink by pressing the drink button on the display.
The strength of the drink is set to default. If you would like to increase or
decrease the strength then follow the steps in the section below.
Stronger drink, Press the
button
or
Weaker drink, Press the
button
Confirm drink by pressing the START button
The display shows:
and the cup light goes on.
Wait until the cup light switches off and the text
has
disappeared from the display before removing the cup.
19
OPERATION
CQube MF & LF
Brewing coffee in a jug (CQube with membrane switch)
STOP
CoffeeC
appuccino
Choco-milk
Small Coffee
Caffè Latte
Hot Water
Espresso
Café Mocca
Café au Lait
Chocolate
A
Lift up the cup shelf and put a jug under the outlet for hot drinks.
Insert user card in the card reader(A)
The display shows
Press the
Service Menu
Jug Beverage
button.
Change the number of cups you want to brew in your jug (6 cup brewing
is the default setting.) with
or
button.
Brewing is possible for up to 12 cups or down to 1 cup.
Press the
button for coffee.
Wait until the cup light switches off and the message
Please wait...
has disappeared from the display before removing the jug.
You can abort the jug process by pressing STOP button any time during the
process, it will finish the drink in process before complete stop.
Remove user card.
Note If no selection is made, remove the user card to abort. Machine
jups back to normal mode.
20
OPERATION
CQube MF & LF
Brewing coffee in a jug (CQube with touchscreen)
A
Lift up the cup shelf and put a jug under the outlet for hot drinks.
Insert user card in the card reader(A).
The display shows as in the figure above.
Press
Change the number of cups you want to brew in your jug With
or
button. (6 Cup brewing is the default setting. Brewing is possible for up
to 12 cups or down to 1 cup.)
Remove user card, drinks that are avalible for brewing jug now appears.
Choose drink by pressing drink button you want.
Press the START button to start dispensing coffee.
Wait until the cup light switches off and the message
has
disappeared from the display before removing the jug.
Note If no selection is made, remove the user card. To stop press the
STOP button.
21
CLEANING PROGRAM
CQube MF & LF
Automatic Cleaning
Automatic rinsing of the mixing bowl
A
Cleaning means
rinsing with water
and rotating the
whipper.
B
Cleaning of the
mixing bowl should
be performed once
per day.
Cleaning hot key
D
For membrane switch
For touchscreen
C
Open the door.
Press ENTER on the cleaning panel inside the door. (See fig. A)
Cleaning Hot key appears on the display (cleaning panel is now active).
the display shows: see fig. C or D.
Put a container that holds at least 0.5 litres under the outlet for hot drinks.
Press button 4 on the cleaning panel. (See fig. B)
The machine will now clean the mixing bowl for 5 seconds.
Close the door to exit cleaning mode and return to normal mode.
Note
22
Repeat the cleaning procedures 2-3 times to get a better
cleaning effect.
CLEANING PROGRAM
CQube MF & LF
Automatic Cleaning
Automatic cleaning of dispenser valves
A
B
Cleaning entails
that the valves
“knock” off any
lime scale and
other particles
that may get stuck
in the cylinders
and flushing them
with water.
Cleaning hot key
D
For membrane switch
For touchscreen
C
Open the door.
Press ENTER on the cleaning panel inside the door. (See fig. A)
Cleaning Hot key appears on the display (Cleaning panel is now active).
the display shows: see fig. C or D.
Put a container that holds at least 0.5 litres under the outlet for hot drinks.
Press button 5 on the cleaning panel. (See fig. B)
The machine will now clean the dispenser valves for 5 seconds.
Close the door to exit cleaning mode and return to normal mode.
Note
Repeat the cleaning procedures 2-3 times to get a better
cleaning effect.
23
CLEANING PROGRAM
CQube MF & LF
Automatic Cleaning
Automatic cleaning of brewing mechanism
Cleaning the
brewing mechanism
should be performed
once a week.
A
B
Total cleaning time
about 10 minutes.
Filter cleaning agent
is avalible from your
dealer:
Product no.
1104161
IMPORTANT!
After cleaning
of the brew
mechanism is
completed, dispense
a cup of coffee and
discard it to remove
cleaning agent
remains in the
filter and brew
chamber.
Cleaning hot key
D
For membrane switch
Open the door.
Press ENTER on the cleaning panel
inside the door. (See the figure A)
Cleaning Hot key appears on the
display (cleaning panel is now active).
the display shows: see the figure C or
D.
Put a container that holds at least 1.8
litres under the outlet for hot drinks.
For touchscreen
C
Press button 3 on the cleaning panel.
(See the figure B)
Display indicates: Place jug, Press ENTER to start
Put 25gr (one portion) of cleaning agent (See fig.E) in brewing mechanism.
Press ENTER on the cleaning panel to start the cleaning process.
Display indicates: Preparing Brewer, Please Wait.
Display indicates: Cleaning Brewer, Time Left 300s. The machine counts down
from 300 seconds.
Fig.E
Display indicates: Rinsing Brewer, Cycles left 7.
Display indicates: Cleaning hot key when the cleaning is complete.
Close the door to exit cleaning mode and return to normal mode.
Note
24
When the cleaning agent has been added, the process must not
be interrupted but be allowed to run its course.
CLEANING PROGRAM
CQube MF & LF
Automatic Cleaning
Open brewer function
A
B
A tool to
disassemble the
coffee filter is
included with the
machine.
Open the door.
Press ENTER on the cleaning panel inside the door. (See fig. A)
Cleaning Hot key appears on the display (cleaning panel is now active).
Put a container that holds at least 0.5 litres under the outlet for hot drinks.
Press button 7 on the cleaning panel. (See fig. B)
The brewing mechanism rotates into position. (See fig. C)
To close brewer press ENTER key on the cleaning panel, the brewer now rotates
to home position.
Close the door to exit cleaning mode and return to normal mode.
8 o’clock
position
C
Note
Can be used to rotate the brewing
mechanism into the correct
position.
“The winder” should be in the 8 o’clock position, If not, remove
again and repeat the process.
25
CLEANING AND CARE
CQube MF & LF
Disassemble the brewing chamber
01
Disassemble the brewing chamber.
Press and lift up the handle on the brewing
chamber.
03
Note: Rinse the brewing chamber under
running water to remove cleaning agent and
coffee remains.
26
02
nce you have lifted the handle, pull the
O
brewing chamber straight out.
04
Reassemble the brewing chamber.
N
ote: When the brewing chamber is
reassembled, ensure that the rubber scraper
(B) ends up between the rocker arms (A).
CLEANING AND CARE
CQube MF & LF
Disassemble and cleaning of coffee filter
Loosen the outlet and insert the tool (A), through one of the holes in the front
of the brewing mechanism all the way to the rear part of the cylinder wall
(Figure 1), move the tool towards the rear section of the filter insert until the
insert is ejected (Figure 2).
25g
A
Figure 1
97 Celsius
3 dl water
Figure 2
10 minutes
Clean the filter insert with 25g cleaning agent dissolved in 3 dl water for max 10
minutes.
Refit the filter. Close the door.
Press the
/ ENTER button and the brewing mechanism will return
to default position.
Remove user card.
Note
Dispense a cup of coffee and discard it to remove cleaning
agent remains in the filter. After having been in contact with
the cleaning agent, the filter must be washed with detergent
and be carefully rinsed under running water.
Is available from your dealer
Cleaning agent: for brewing mechanism
Filter: for brewing mechanism
Tool: for disassembly of filter
Product No. 1104161
Product No. 47200213
Product No. 4720090
27
CLEANING AND CARE
CQube MF & LF
Weekly cleaning
Disassemble mixing system
Rotate the canister chutes so they point
upwards and pull out the outlet hose.
01
02
Turn the mounting plate lever anticlockwise.
03
04
Loosen the mixing bowl by pulling it straight
out.
Loosen the whipper by pulling it straight out.
05
Loosen the mounting plate. Turn the lever
anticlockwise, until it stops.
06
Pull the mounting plate straight out.
28
Reassembling mixing system
See the next page
CLEANING AND CARE
CQube MF & LF
Weekly Cleaning
Wash these parts
Mixing Bowl
Condensation Trap
Mounting Plate
Whipper
Clean with a moist
cloth and wipe dry.
All parts must be dry before reassembly.
Reassemble mixing system
01
02
The flat side of the whipper shaft must
correspond with the marked arrow on the
whipper.
To fit the whipper push onto the shaft until a click
sound can be heard. It is only possible to assemble
the whipper in one way.
Check all seals (red) before
reassembly of parts.
03
Fix the mixing bowl and condensation trap. Pushfit the mixing bowl and fix with lever.
Connect the outlet hose.
Note
04
Ensure that all water hoses have
been connected and fitted.
29
CLEANING AND CARE
CQube MF & LF
Exterior cleaning
Exterior cleaning when necessary
To clean the exterior of the machine, use a soft cloth
and liquid cleaning agent that is non-abrasive.
If using a machine equipped with touchscreen do not
spray cleaning liquid directly on the display. Use only
LCD screen cleaner designed for touchscreen cleaning.
Clean the bean hopper
Close the bean stop.
Lift the bean hopper up to remove it. Use a soft cloth
and liquid cleaning agent that is non-abrasive.
Note Ensure that the bean hopper is completely
dry before refitting.
Clean the grinder
Cleaning of the grinder shall be performed once per
month in conjunction with technical maintenance.
30
MESSAGE SHOWN ON DISPLAY
Message On Display
CQube MF & LF
Indication
Energy Saving Mode
The machine is in energy saving mode.
Not Available
Drink can not be selected as jug.
Heating Water
Please Wait...
Low temperature in the water tank, the machine is heating up
(blocked).
Low Water Level
Press Enter Key
Low water level in water tank. Press enter key to start filling up the
water tank.
Filling Water
Please Wait...
The machine is filling water.
Warning
Low Temperature
Temperature is low, It is still possible to dispense drink.
Low temperature
Blocked
Temperature is low, the machine is blocked.
Empty Drip Tray
The drip tray is full of water.
Low Water
Level Blocked
The water level in the water tank is low, it is not possible to
dispense drink.
Check
Water Supply
The water has not reached the correct level in the water tank,
check the water inlet hose, restart the machine.
Empty Waste Box
The waste box is full, open the door and empty out the grounds.
When closing the door, press E to reset the counter. Selectable in
main program.
Change Brewer Filter
The brewing filter is clogged. The filter needs replacing or to be
cleaned.
Place Cup
If the cup sensor has been activated, this is shown if no cup has
been placed on the drip tray.
Bev. Disabled
The drink has been disabled.
Door Open
The door is open.
Change
Water Filter
The water filter needs replacing, press the button E to reset the
counter.
31
PROGRAMMING
CQube MF & LF
Activate programming with the user card
A
Insert user card in the card reader (A)
The display will look like this for membrane switch:
Service Menu
Clean Machine
Press
to go forward
Service Menu
Counters
Press
to go forward
The display will look like this for touchscreen:
32
PROGRAMMING
CQube MF & LF
Jug beverage
Service Menu
Jug Beverage
How to dispense a jug of a drink.
Press
Press
Jug Beverage
Press
Cups
1-12
Select the number of cups to be brewed in
the jug. Press the desired drink to start the
brewing.
If no selection is made, remove user card to
return to the default setting.
To stop, Press the STOP button.
33
PROGRAMMING
CQube MF & LF
Clean machine
Open the door. Press ENTER on the cleaning panel
inside the door. Choose button X for each cleaning.
Cleaning hot key
See the pages for
cleaning programs
in order to
perform cleaning.
3
Press
4
5
Enter
7
8
10
34
Press
Press
Press
Press
Press
Press
Clean Brewer
Clean Mixer
Clean Valves
Open\Rotate Brewer
Clean Grinder
Rinse Brewer
PROGRAMMING
CQube MF & LF
Counters
See the counter of each drink or total counters for all
drinks. It’s also possible to reset the drink counters.
Service Menu
Counters
Service Menu
Counters
Press
Press
Counters
Beverages
Press
Beverage Counters
Per Beverage
Drink 1
served xxx
Press
Press
Press
to
Drink 2
served xxx
go forward in the menu
Press
Press
Beverage Counter
Total Served
Total Beverages
Served xxx
Press
Press
Beverage Counter
Master Total
Master Total
Served xxx
Press
Press
Beverage Counter
Clear Counters
Hold Enter to
Clear Counters
Hold ENTER key
for 3 seconds
Press
to go back in the menu
Counters Cleared
Press Back
35
PROGRAMMING
CQube MF & LF
Counters
See the number of times cleaning has been performed
or reset the clean counter.
Service Menu
Counters
Press
Clean Counter
Brewer xxx
Counters
Clean Counter
Press
to go forward in the menu
Clean Counter
Total xxx
Press
Press
to go back in the menu
Press
Counters
Water Filter
Press
Reset? NO/YES
Months Left 6
Water Filter
Reset Filter
Standard=6 months
Press
to go forward in the menu
Press
Water Filter
Interval 6
Press
36
to go back in the menu
Water Filter
Interval 1-12
DIMENSION SKETCH
CQube MF & LF
CQube MF13 & MF04
C
A
B
D
Model
A
B
C
D
E
CQube MF13
882mm
427mm
550mm
110mm
155mm
CQube MF04
882mm
427mm
550mm
110mm
155mm
E
37
DIMENSION SKETCH
CQube MF & LF
CQube LF13 & LF04
C
A
B
D
Model
A
B
C
D
E
CQube LF13
995mm
420mm
565mm
110mm
155mm
CQube LF04
995mm
420mm
565mm
110mm
155mm
38
E
For the warranty to be valid the conditions for maintenance must have been
followed according to our instructions, proper precaution has been made and
warranty claim been issued without delay.
The affected equipment may not be used during awaiting service if there is any risk
that the damage or defect would worsen.
The warranty will not cover consumption supplies such as glassware, normal
maintenance such as cleaning of filters, contaminations in water, lime, incorrect
voltages, pressure or adjustment of water amounts.
The warranty will not cover damages of defects caused by incorrect handling and
operation of the appliance.
FOR SERVICE
Please contact your dealer
Your Dealer
www.creminternational.com