RX-V630RDS AV Receiver DSP-AX630SE AV Amplifier

GB
RX-V630RDS
DSP-AX630SE
AV Receiver
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
0100V630(GB)-cv1/4
1
RX-V630RDS/DSP-AX630SE
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
Printed in Malaysia
AV Amplifier
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
V874860
1/10/02, 3:41 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
16
When not planning to use this unit for long
periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
2
Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, 20 cm on the
left and right, and 10 cm at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
17
Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding
that this unit is faulty.
18
Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
19
VOLTAGE SELECTOR (China and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
3
4
5
6
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
On the top of this unit, do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may
cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
7
Do not plug in this unit to a wall outlet until all
connections are complete.
8
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9
Do not use force on switches, knobs and/or cords.
10
When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12
Only voltage specified on this unit must be used.
Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.
13
To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
14
Take care of this unit so that no foreign objects
and/or liquid drops inside this unit.
15
Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
■ For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
• The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION
0101V630_Cau_EN(GB)
2
1/11/02, 7:39 PM
INTRODUCTION
CONTENTS
CONTENTS ............................................................ 1
FEATURES ............................................................. 2
GETTING STARTED ............................................ 3
Checking the package contents ................................. 3
Installing batteries in the remote control ................... 3
CONTROLS AND FUNCTIONS ......................... 4
PREPARATION
SET MENU ........................................................... 42
Adjusting the items on the SET MENU .................. 42
1 SPEAKER SET (speaker mode settings) ............ 43
2 LFE LEVEL ........................................................ 45
3 SP DLY TIME (speaker delay time) ................... 45
4 D. RANGE (dynamic range) ............................... 46
5 L/R BALANCE (balance of the main left and
right speakers) ..................................................... 46
6 HP TONE CTRL (headphone tone control) ........ 46
7 I/O ASSIGN (input/output assignment) .............. 46
8 INPUT MODE (initial input mode) .................... 47
9 DISPLAY SET .................................................... 47
10MEM. GUARD (memory guard) ........................ 47
PREPARATION
Front panel ................................................................ 4
Remote control .......................................................... 6
Using the remote control ........................................... 7
Front panel display .................................................... 8
INTRODUCTION
ADVANCED OPERATION
INTRODUCTION
REMOTE CONTROL FEATURES ................... 48
SPEAKER SETUP ................................................. 9
Speakers .................................................................... 9
Speaker placement .................................................... 9
Connecting the speakers .......................................... 10
Before connecting components ............................... 13
Connecting video components ................................ 14
Connecting audio components ................................ 16
Connecting the antennas ......................................... 17
Connecting an external amplifier ............................ 18
Connecting an external decoder .............................. 18
Connecting the power supply cords ........................ 19
Turning on the power .............................................. 19
Before you begin ..................................................... 21
Using the test tone ................................................... 21
Changing parameter settings ................................... 53
PRO LOGIC Music parameter descriptions ....... 53
ADDITIONAL INFORMATION
ADVANCED
OPERATION
SPEAKER MODE SETTINGS .......................... 20
ADJUSTING SPEAKER OUTPUT LEVELS .. 21
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ....................................................... 51
ADJUSTING THE DELAY TIME ..................... 52
ADJUSTING THE PARAMETER SETTINGS
FOR PRO LOGIC MUSIC ......................... 53
BASIC
OPERATION
CONNECTIONS .................................................. 13
Control area ............................................................. 48
Setting the manufacturer code ................................. 49
Clearing setup manufacturer codes ......................... 49
Controlling other components ................................. 50
TROUBLESHOOTING ...................................... 54
GLOSSARY .......................................................... 58
SPECIFICATIONS .............................................. 60
BASIC OPERATION
BASIC PLAYBACK ............................................ 23
ADDITIONAL
INFORMATION
Input modes and indications .................................... 25
Selecting a sound field program .............................. 26
DIGITAL SOUND FIELD PROCESSING
(DSP) ................................................................. 29
Understanding sound fields ..................................... 29
Hi-Fi DSP programs ................................................ 29
CINEMA-DSP ...................................................... 30
Sound design of CINEMA-DSP ............................. 30
CINEMA-DSP programs ........................................ 32
TUNING
RX-V630RDS
......................................... 34
Automatic and manual tuning ................................. 34
Presetting stations .................................................... 35
Tuning in to a preset station .................................... 37
Exchanging preset stations ...................................... 37
RECEIVING RDS STATIONS
RX-V630RDS
.... 38
Description of RDS data ......................................... 38
Changing the RDS mode ......................................... 38
PTY SEEK function ................................................ 39
EON function .......................................................... 39
SLEEP TIMER ..................................................... 40
English
Setting the sleep timer ............................................. 40
Canceling the sleep timer ........................................ 40
RECORDING ....................................................... 41
1
0102V630_1-8_EN(GB)
1
1/11/02, 7:40 PM
FEATURES
Built-in 6-channel power amplifier
Other features
◆ Minimum RMS output power
(0.06% THD, 20 Hz – 20 kHz, 8Ω)
Main:
75 W + 75 W
Center:
75 W
Rear:
75 W + 75 W
Rear center: 75 W
◆ 96-kHz/24-bit D/A converter
◆ “SET MENU” for optimizing this unit for your
Audio/Video system
◆ Test tone generator for easier speaker balance
adjustment
◆ 6-channel external decoder input
◆ S-video signal input/output capability
◆ Component video input/output capability
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Remote control with preset manufacturer codes
Multi-mode digital sound field
processing
◆
◆
◆
◆
Dolby Pro Logic/Dolby Pro Logic decoder
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES compatible decoder
CINEMA DSP: Combination of YAMAHA DSP
technology and Dolby Pro Logic, Dolby Digital
or DTS
◆ Virtual CINEMA DSP
◆ SILENT CINEMA DSP
Sophisticated AM/FM Tuner
RX-V630RDS
◆ 40-Station random access preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (Preset
editing)
■ About this manual
• This document is the owner’s manual for both RX-V630RDS and DSP-AX630SE. Since DSP-AX630SE does not incorporate a
tuner, descriptions on tuning are not applicable for DSP-AX630SE. Illustrations for the RX-V630RDS are mainly used for
explanations.
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement
in operativity ability, and others. In this case, the product has priority.
Manufactured under license from Dolby Laboratories.
“DTS”, “ES” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
2
0102V630_1-8_EN(GB)
2
1/11/02, 7:40 PM
GETTING STARTED
INTRODUCTION
Checking the package contents
Check your package to make sure it contains the following items.
Remote control
Batteries (4)
(AAA, R03, UM-4)
RX-V630RDS
TRANSMIT
CODE SET
SYSTEM
POWER
STANDBY
POWER
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
+
+
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
Indoor FM antenna
(U.S.A., Canada, China,
Korea and General models)
75-ohm/300-ohm antenna
adapter (U.K. model)
(Europe, U.K., Australia and
Singapore models)
PREPARATION
+
TV VOL
AM loop antenna
–
MUTE
HALL
ROCK
CONCERT
JAZZ CLUB
ENTERTAINMENT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
9
Front VIDEO AUX jack cap
ENTER
EFFECT
LEVEL
PRESET/CH
SET MENU
MENU
TITLE
A/B/C/D/E
SELECT
+
BASIC OPERATION
–
TEST
RETURN
DISPLAY
REC
AUDIO
DISC SKIP
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
1
• Change all of the batteries if you notice a decrease in
the operating range of the remote control, that the
indicator does not flash, or the light becoming dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing
new batteries.
Press the
part and slide off the battery
compartment cover.
2
Insert the four supplied batteries (AAA, R03,
UM-4) according to the polarity markings on
the inside of the battery compartment.
3
Slide the cover back on so that it snaps into
place.
English
1
APPENDIX
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code that may have
been cleared.
3
3
0102V630_1-8_EN(GB)
3
ADDITIONAL
INFORMATION
2
■ Notes on batteries
ADVANCED
OPERATION
Installing batteries in the remote
control
1/11/02, 7:40 PM
CONTROLS AND FUNCTIONS
Front panel
1
2
3
4
5
6
INPUT
7
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
RDS MODE/FREQ
PRESET/TUNING
EON
FM/AM
EDIT
STANDBY
/ON
PTY SEEK
MODE
START
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
SILENT
TREBLE
SPEAKERS
A
VIDEO AUX
STEREO
B
PROGRAM
A/B/C/D/E
PRESET/TUNING
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
(RX-V630RDS)
8
9
0
RDS MODE/FREQ
q
EON
w
e
r
t
y
PRESET/TUNING
DSP-AX630SE
FM/AM
EDIT
PTY SEEK
MODE
START
–
SET MENU
+
NEXT
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
ui o p
w
e
as d f
1 STANDBY/ON
5 INPUT l / h
Turns this unit on, or set it to the standby mode. When
you turn this unit on, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Selects the input source you want to listen to or watch.
Standby mode
In this mode, this unit will consume a small amount of
power in order to receive infrared-signals from the
remote control.
2 Remote control sensor
Receives signals from the remote control.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the OUT (REC) level.
7 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks. This audio takes priority over the source selected
with INPUT l / h (or the input selector buttons on the
remote control).
Shows information about the operational status of this
unit.
8
SILENT (PHONES jack)
Allows you enjoy DSP effect for private listening with
headphones. When you connect headphones, no signals
are output to the speakers or the OUTPUT jacks.
4 INPUT MODE
9 SPEAKERS A/B
Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) to receive when one component is
connected to two or more input jacks. Priority cannot be
set when 6CH INPUT is selected as the input source.
Turns the set of main speakers connected to the A and/or
B terminals on or off.
3 Front panel display
4
0102V630_1-8_EN(GB)
4
1/11/02, 7:40 PM
CONTROLS AND FUNCTIONS
0 STEREO/EFFECT
RX-V630RDS
u RDS MODE/FREQ
q PROGRAM l / h
When an RDS station is received, press this button to
change the display mode among the PS mode, PTY
mode, RT mode, CT mode (if the station offers those
RDS data service) and/or frequency display mode in
turn.
Selects the DSP program.
i PTY SEEK MODE
w
Press this button to set the unit in the PTY SEEK
mode.
SET MENU –/+
Adjusts the setting on the SET MENU.
DSP-AX630SE
o PTY SEEK START
Press this button to begin searching for a station after
the desired program type has been selected in the PTY
SEEK mode.
p EON
Press this button to select the desired program type
(NEWS, INFO, AFFAIRS, SPORT) when you want to
tune in to a radio program of that type automatically.
DSP-AX630SE NEXT
Selects the SET MENU mode.
a PRESET/TUNING (EDIT)
r BASS
Adjusts the low-frequency response for the main left and
right channels.
Turn right to increase or turn left to decrease the lowfrequency response.
Adjusts the high-frequency response for the main left and
right channels.
Turn right to increase or turn left to decrease the highfrequency response.
s TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic and
manual.
d MEMORY (MAN’L/AUTO FM)
Stores the current station in the memory.
f FM/AM
y VIDEO AUX jacks
Switches the reception band between FM and AM.
ADDITIONAL
INFORMATION
Inputs for audio and video signals from a portable
external source (game console, etc.). Set the input source
to V-AUX to enjoy source signals from these jacks.
When the VIDEO AUX jacks on the front panel are not
used, you can attach the provided front VIDEO AUX jack
cap as shown in the illustration. When the cap is not
attached, be sure retain it carefully.
EO
Switches the function of PRESET/TUNING l / h
between selecting a preset station number and tuning
(the colon (:) turns on or off).
This button is also used to exchange the assignment of
two preset stations with each other.
ADVANCED
OPERATION
t TREBLE
BASIC OPERATION
A/B/C/D/E
Selects preset station groups A to E.
e
RX-V630RDS
PREPARATION
PRESET/TUNING l / h
Selects preset station numbers 1 to 8 when the colon (:)
appears in the front panel display.
Selects the tuning frequency when the colon (:) does not
appear.
RX-V630RDS
INTRODUCTION
Switches between normal stereo and DSP effect
reproduction. When STEREO is selected, 2-channel
signals are directed to the main left and right speakers
without effect sounds and all Dolby Digital and DTS
signals (except the LFE channel) are mixed down to the
main left and right speakers.
X
AU
VID
APPENDIX
AL
TIC
OP
L
AU
DIO
R
EO
VID
IDEO
SV
English
5
0102V630_1-8_EN(GB)
5
1/11/02, 7:40 PM
CONTROLS AND FUNCTIONS
Remote control
This section describes the remote control controls and
their functions. Make sure that the AMP mode is selected
before starting operation. See “REMOTE CONTROL
FEATURES” on pages 48 to 50.
1
2
TRANSMIT
CODE SET
SYSTEM
STANDBY
POWER
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
9
3 Input selector buttons
0
Select the input source and set the remote control to
operate the selected source component.
q
4 DSP program
w
Select DSP programs for the AMP position. Press a
button repeatedly to select a DSP program within that
group.
e
r
+
+
+
TV VOL
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
t
y
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
9
ENTERTAINMENT
ENTER
LEVEL
PRESET/CH
A/B/C/D/E
6
–
SELECT
+
8 TRANSMIT indicator
u
Flashes while the remote control is sending signals.
9 STANDBY
i
Sets this unit in the standby mode.
0 SYSTEM POWER
Turns on the power of this unit.
TEST
7
Used when changing the setting and to implement the
settings.
Outputs the test tone to adjust the speaker levels.
SET MENU
MENU
TITLE
6 Multi control section
7 TEST
EFFECT
5
5 LEVEL
Selects the effect speaker channel to be adjusted.
MUTE
4
2 CODE SET
Used when setting up the manufacturer code (see page
49).
AMP
A
Outputs infrared control signals. Aim this window at the
component you want to operate.
8
POWER
3
1 Infrared window
DISPLAY
RETURN
REC
AUDIO
DISC SKIP
q SLEEP
Sets the sleep timer.
w 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks.
e AMP
Sets the remote control to the AMP mode for controlling
this unit.
r Å
Sets the remote control to operate other component (not
necessarily connected to this unit) without changing this
unit’s input source.
t VOLUME +/–
Increases or decreases the volume level.
y MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
6
0102V630_1-8_EN(GB)
6
1/11/02, 7:40 PM
CONTROLS AND FUNCTIONS
u STEREO/EFFECT
Using the remote control
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
SILENT
i SET MENU
INTRODUCTION
Switches between normal stereo and DSP effect
reproduction. When STEREO is selected, 2-channel
signals are directed to the main left and right speakers
without effect sounds and all Dolby Digital and DTS
signals (except the LFE channel) are mixed down to the
main left and right speakers.
TREBLE
SPEAKERS
A
B
VIDEO AUX
PROGRAM
STEREO
PRESET/TUNING
A/B/C/D/E
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
Selects the SET MENU mode.
30°
30°
PREPARATION
VCR 1
Approximately 6 m (20 feet)
VCR2/DVR
■ Handling the remote control
ADVANCED
OPERATION
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity or temperature such as near a heater,
stove or bath;
– dusty places; or
– in places subject to extremely low temperatures.
BASIC OPERATION
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
ADDITIONAL
INFORMATION
APPENDIX
English
7
0102V630_1-8_EN(GB)
7
1/11/02, 7:40 PM
CONTROLS AND FUNCTIONS
Front panel display
1
MATRIX
2
VCR2/DVR
DIGITAL VIRTUAL
SILENT
PRO LOGIC /
3
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
MUTE VOLUME
DTS
DOLBY DIGITAL PRO LOGIC
PS PTY RT CT STEREO AUTO SLEEP
MOVIE THTR 12 ENTERTAINMENT EON PTY HOLD TUNED MEMORY
VCR1
L
DSP
dB
mS
PCM
5
4
6
7
8
9
C R
LFE RL RC RR
0 q w e r t
y
(RX-V630RDS)
1 Processor indicators
Lights up when the t, g, VIRTUAL,
PRO LOGIC /
or DSP are activated.
RX-V630RDS
0 RDS indicator
3 MUTE indicator
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
EON indicator lights up when an RDS station that
offers the EON data service is being received.
PTY HOLD indicator lights up while searching for
stations in the PTY SEEK mode.
Flashes while the MUTE function is on.
q STEREO indicator
4 VOLUME level indicator
Lights up when this unit is receiving a strong signal
for an FM stereo broadcast while the “AUTO”
indicator is lit.
MATRIX lights up when the Dolby Digital EX decoder or
the DTS-ES compatible decoder is activated.
2 Input source indicator
Shows the current input source with a cursor.
Indicates the volume level.
5 v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
w TUNED indicator
Lights up when this unit is tuned to a station.
6 SILENT indicator
e MEMORY indicator
Lights up when headphones are connected while the
digital sound field processor is on.
r AUTO indicator
7 Headphones indicator
Shows that this unit is in the automatic tuning mode.
Flashes to show a station can be stored.
Lights up when headphones are connected.
8 DSP program indicators
The name of the selected DSP program lights up when the
ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or V/DTS SURROUND DSP program is
selected.
t SLEEP indicator
Lights up while the sleep timer is on.
y Input channel indicator
Indicates the channel components of input signals being
received.
9 Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
8
0102V630_1-8_EN(GB)
8
1/11/02, 7:40 PM
PREPARATION
SPEAKER SETUP
Speaker placement
■ Use of a subwoofer expands your
sound field
Rear speaker (R)
Subwoofer
Main
speaker (L)
1.8 m (6 feet)
Rear center
speaker
Rear speaker (L)
■ Main speakers
Place the main left and right speakers an equal distance
from the ideal listening position. The distance between
each speaker and each side of the video monitor should
also be the same.
■ Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible (such as directly over or under the
monitor) and centrally between the main speakers.
■ Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (6 feet) above the
floor.
■ Rear center speaker
Place the rear center speaker in the center between the
rear left and right speakers at the same height from the
floor as the rear speakers.
■ Subwoofer
Note
• If you do not use any of effect speakers (rear, center and/or rear
center), change the settings of SPEAKER SET items at the
SET MENU to designate the signals to other terminals you
connect speakers to.
English
CAUTION
Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
9
0103V630_9-18_EN(GB)
9
1/11/02, 7:40 PM
APPENDIX
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce wall
reflections.
ADDITIONAL
INFORMATION
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
playing back Dolby Digital or DTS signals. The
YAMAHA Active Servo Processing Subwoofer System is
ideal for natural and lively bass reproduction.
Main speaker (R)
ADVANCED
OPERATION
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.
Center speaker
BASIC OPERATION
The main speakers are used for the main source sound
plus effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for effect and surround sounds. The center speaker is
for the center sounds (dialog, vocals, etc.). The rear center
speaker supplements the rear (left and right) speakers and
provides for more realistic front-to-back transitions.
Refer to the following diagram when you place the
speakers.
PREPARATION
This unit has been designed to provide the best soundfield quality with a 6-speaker system, using main left and
right speakers, rear left and right speakers, a center
speaker, and a rear center speaker. If you use different
brands of speakers (with different tonal qualities) in your
system, the tone of a moving human voice and other types
of sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
INTRODUCTION
Speakers
SPEAKER SETUP
Connecting the speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
• Use speakers with the specified impedance shown on the rear panel of this unit.
• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit
and/or the speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
■ Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridge.
10 mm (3/8”)
1
2
1
Remove approximately 10 mm (3/8”) of
insulation from each of the speaker cables.
2
Twist the exposed wires of the cable
together to prevent short circuits.
■ Connecting to the SPEAKERS terminals
2
Red: positive (+)
Black: negative (–)
3
1
1
2
Unscrew the knob.
3
Tighten the knob to secure the wire.
Insert one bare wire into the hole in the side
of each terminal.
■ MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be
connected to either the MAIN A or the MAIN B terminals.
■ REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
■ CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
■ REAR CENTER SPEAKER terminals
A rear center speaker can be connected to these terminals.
10
0103V630_9-18_EN(GB)
10
1/11/02, 7:40 PM
SPEAKER SETUP
Main B speaker
Right
Main A speaker
Left
Right
Left
Center
speaker
2
VIDEO
AUDIO
L
R
S VIDEO
+
COMPONENT VIDEO
PB/CB
PR/CR
GND
B
Y
DVD
IN
UNBAL.
D-TV
/CBL
R
FM
ANT
REAR
(SURROUND)
R
L
L
OUTPUT
L
R
MONITOR
OUT
REAR
CENTER
MAIN
CENTER
DVD
SURROUND
SUB
WOOFER CENTER
VIDEO
MONITOR OUT
OUTPUT
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
R
REAR
(SURROUND)
L
SET BEFORE POWER ON
IMPEDANCE SELECTOR
BASIC OPERATION
6CH INPUT
S VIDEO
MAIN A OR B: 8
A+B:16
: 8
CENTER
REAR CENTER : 8
: 8
REAR
MAIN
A OR B :4 MIN. /SPEAKER
A+B :8 MIN. /SPEAKER
CENTER :6 MIN. /SPEAKER
REAR CENTER
:6 MIN. /SPEAKER
REAR :6 MIN. /SPEAKER
SUB
WOOFER
MD/CD-R
OPTICAL
DIGITAL
OUTPUT
AC OUTLETS
+
+
D-TV
/CBL
MAIN
–
–
OUT
VCR 1
75
MD/CD-R
–
TUNER
AM
ANT
OUT
(REC)
MD
/CD-R
IN
(PLAY)
–
PREPARATION
DVD
–
IN
CD
+
A
VCR 2
/VDR
CD
CENTER
+
VIDEO
OUT
COAXIAL
OPTICAL
D-TV/CBL
3
SPEAKERS
REAR CENTER
L
MAIN
R
AUDIO
DIGITAL
INPUT
INTRODUCTION
1
(RX-V630RDS)
5
4
Right
7
Left
Rear speaker
3
ADVANCED
OPERATION
Subwoofer
system
6
Rear center
speaker
1
4
2
ADDITIONAL
INFORMATION
5
7
6
The diagram shows the speaker layout in the listening
room.
When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,
connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or
rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency
effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your
SPEAKER SET selections.
11
0103V630_9-18_EN(GB)
11
1/11/02, 7:40 PM
English
Notes
• The cut-off frequency of the SUBWOOFER jack is 90 Hz.
• If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET
item “1E BASS” on the SET MENU to MAIN.
• Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this unit’s remote
control (see “ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS” on page 51).
APPENDIX
■ SUBWOOFER jack
SPEAKER SETUP
■ IMPEDANCE SELECTOR switch
WARNING
Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage
the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE
SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when
this unit is in the standby mode.
Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this
switch only when this unit is in the standby mode.
IMPEDANCE
SELECTOR
switch
Switch
position
Speaker
Main
MAIN A OR B: 8
A+B:16
: 8
CENTER
REAR CENTER: 8
: 8
REAR
MAIN
A OR B :4 MIN. /SPEAKER
A+B :8 MIN. /SPEAKER
CENTER :6 MIN. /SPEAKER
REAR CENTER
:6 MIN. /SPEAKER
REAR :6 MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
SET BEFORE POWER ON
Impedance level
If you use one set of main speakers,
the impedance of each speaker must
be 4 Ω or higher.
If you use two sets of main speakers,
the impedance of each speaker must
be 8 Ω or higher.
IMPEDANCE SELECTOR
Left
SPEAKERS
REAR CENTER
L
MAIN
R
+
CENTER
+
+
–
–
A
–
Center
The impedance must be 6 Ω or
higher.
Rear
Center
The impedance must be 6 Ω or
higher.
Rear
–
–
OMPONENT VIDEO
R/CR
PB/CB
B
Y
REAR
(SURROUND)
R
L
Main
If you use one set of main speakers,
the impedance of each speaker must
be 8 Ω or higher.
If you use two sets of main speakers,
the impedance of each speaker must
be 16 Ω or higher.
[Canada model only]
The impedance of each speaker must
be 8 Ω or higher.
Center
The impedance must be 8 Ω or
higher.
Rear
Center
The impedance must be 8 Ω or
higher.
+
+
R
L
OUTPUT
L
R
MAIN
MAIN
A OR B :4 MIN. /SPEAKER
A+B :8 MIN. /SPEAKER
CENTER :6 MIN. /SPEAKER
REAR CENTER
:6 MIN. /SPEAKER
REAR :6 MIN. /SPEAKER
The impedance of each speaker must
be 6 Ω or higher.
MAIN A OR B: 8
A+B:16
: 8
CENTER
REAR CENTER: 8
: 8
REAR
REAR
CENTER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
CENTER
R
REAR
(SURROUND)
L
SET BEFORE POWER ON
IMPEDANCE SELECTOR
(RX-V630RDS)
Right
Rear
The impedance of each speaker must
be 8 Ω or higher.
12
0103V630_9-18_EN(GB)
12
1/11/02, 7:40 PM
CONNECTIONS
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. To enjoy multi-channel sound track
of DVD software, etc. with DSP effect, you need to make
digital connection. All digital input jacks are acceptable
for 96-kHz sampling digital signals.
CAUTION
Do not connect this unit or other components to the
mains power until all connections between the
components have been completed.
BASIC OPERATION
DIGITAL INPUT jacks
(pages 13-16)
Note
• The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
Antenna input terminals
(page 17)
Speaker terminals
(pages 10-11)
(RX-V630RDS)
MAIN
R
AUDIO
DIGITAL
INPUT
AUDIO
L
R
SPEAKERS
REAR CENTER
L
+
VIDEO
S VIDEO
VIDEO
L
VCR 2
/VDR
DVD
–
IN
CD
COMPONENT VIDEO
PR/CR
PB/CB
GND
DVD
D-TV
/CBL
SURROUND
DVD
UNBAL.
D-TV
/CBL
FM
ANT
SUB
WOOFER
6CH INPUT
REAR
(SURROUND)
R
L
R
MAIN
L
L
REAR
CENTER
CENTER
R
S VIDEO
REAR
(SURROUND)
L
VIDEO
MONITOR OUT
OUTPUT
SUBWOOFER OUTPUT
jack (page 11)
DIGITAL OUTPUT jack
(page 16)
APPENDIX
6CH INPUT jacks
(page 18)
R
OUTPUT
MONITOR
OUT
DIGITAL
OUTPUT
+
+
MAIN
SUB
WOOFER CENTER
–
B
Y
IN
MD/CD-R
OPTICAL
–
–
OUT
VCR 1
75
MD/CD-R
–
TUNER
AM
ANT
OUT
(REC)
MD
/CD-R
IN
(PLAY)
+
ADDITIONAL
INFORMATION
R
CD
CENTER
+
A
OUT
COAXIAL
OPTICAL
D-TV/CBL
ADVANCED
OPERATION
Video component jacks
(pages 14-15)
Audio component jacks
(page 16)
PREPARATION
• Be sure all connections are made correctly, that is to
say L (left) to L, R (right) to R, “+” to “+” and “–” to
“–”. Some components require different connection
methods and have different jack names. Refer to the
operation instructions for each component to be
connected to this unit.
• When you connect other YAMAHA audio components
(such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same
number labels as !, #, $ etc. YAMAHA applies this
labeling system to all its products.
• After you have completed all connections, check them
again to make sure they are correct.
• The name of jack corresponds to input selector.
INTRODUCTION
■ Connecting to digital jacks
Before connecting components
AC OUTLETS
(page 19)
OUTPUT jacks
(page 18)
English
13
0103V630_9-18_EN(GB)
13
1/11/02, 7:40 PM
CONNECTIONS
Connecting video components
Refer to the connection examples on the next page.
■ Types of video jacks
There are three types of video jacks as follows:
COMPONENT VIDEO
S VIDEO
VIDEO
2
1
PR/CR
PB/CB
Y
3
1 VIDEO jack
Conventional composite video signal.
2 S VIDEO jack
Transmits color and luminance separately and achives
high-quality color reproduction.
3 COMPONENT VIDEO jacks
Transmit color difference (PB/CB, PR/CR) and luminance
separately and provide the best quality picture.
• Each type of video jack works independently. Signals
input through the composite video, S-video and
component jacks are only output through the
corresponding composite video, S-video, and
component jacks.
• Use a commercially available cable specified for
connecting each type of jacks.
• The description of the component video jacks may differ
depending on the component (e.g. Y, CB, CR/Y, PB, PR/Y,
B-Y, R-Y etc.). When using these jacks, refer also to the
operation instructions for the component being connected.
■ Connecting a video monitor
Connect the video input jack on your video monitor to the
MONITOR OUT VIDEO jack.
Note
• If you connect this unit with a source component using S-video
(or Component video) jacks, you also need to connect your
video monitor using S-video (or Component video) jacks.
■ Connecting a DVD player/digital
TV/cable TV
Connect the optical digital audio signal output jack on
your component to the DIGITAL INPUT jack and
connect the video signal output jack on the component to
the VIDEO jack on this unit.
Then connect AUDIO jacks on your component to the
AUDIO jacks on this unit.
y
• If your video component has an S-video output or component
video output, connect the S-video signal output jack on the
component to the S VIDEO jack or connect the component
video signal output jacks on the component to the
COMPONENT VIDEO jacks.
• The AUDIO jacks are available for a video component which
does not have optical digital output jack. However, multichannel reproduction cannot be obtained with audio signals
input from AUDIO jacks.
■ Connecting a game console or
camcorder
Connect the optical digital audio signal output jack on
your video component to the OPTICAL jack on the front
panel and connect video signal output jack on the
component to the VIDEO jack on the front panel.
y
• If your video component has an S-video output, connect the Svideo signal output jack on the component to the S VIDEO
jack.
• The AUDIO jacks are available for a video component such as
a camcorder which does not have optical digital output jack.
■ Connecting a VCR or DVR (digital
video recorder)
Connect the audio signal input jacks on your video
component to the AUDIO OUT jacks and connect the
video signal input jack on the video component to the
VIDEO OUT jack on this unit for picture recording.
Connect the audio signal output jacks on your component
to the AUDIO IN jacks and connect the video signal
output jack on the component to the VIDEO IN jack on
this unit to play a source from your recording component.
Second VCR or digital video recorder can be connected
using VCR 2/DVR jacks.
y
• If your video component has an S-video input, connect the Svideo signal input jack on the component to the S VIDEO OUT
jack.
• If your video component has an S-video output, connect the Svideo signal output jack on the component to the S VIDEO IN
jack.
Notes
• Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
• S-video and component video signals pass independently
through this unit’s video circuit. Make sure to connect this unit
to both a source component and a recording component using
the video jacks of the same system.
14
0103V630_9-18_EN(GB)
14
1/11/02, 7:40 PM
CONNECTIONS
O
VCR 1
AUDIO
INPUT
R
L
L
AUDIO
DIGITAL
INPUT
VIDEO
INPUT
AUDIO
V
V
VIDEO
S VIDEO
L
R
VIDEO
OUTPUT
VIDEO
OUTPUT
V
R
INTRODUCTION
AUDIO
OUTPUT
TV/digital TV/
cable TV
OPTICAL
OUTPUT
VIDEO
PREPARATION
OUT
R
CD
L
VCR 2
/VDR
IN
CD
TUNER
AM
ANT
COAXIAL
OPTICAL
D-TV/CBL
OUT
VCR 1
DVD
OUT
(REC)
MD
/CD-R
IN
(PLAY)
MD/CD-R
MAIN
D-TV
/CBL
SURROUND
DVD
COMPONENT VIDEO
PR/CR
PB/CB
GND
Y
DVD
IN
75
UNBAL.
D-TV
/CBL
FM
ANT
MONITOR
OUT
SUB
WOOFER CENTER
DIGITAL
OUTPUT
VIDEO
S VIDEO
6CH INPUT
MONITOR OUT
OUTPUT
V
V
(RX-V630RDS)
BASIC OPERATION
MAIN
A OR B :4 MIN. /SPEAKER
A+B :8 MIN. /SPEAKER
CENTER :6 MIN. /SPEAKER
REAR CENTER
:6 MIN. /SPEAKER
REAR :6 MIN. /SPEAKER
SUB
WOOFER
MD/CD-R
OPTICAL
R
L
VIDEO
INPUT
VIDEO
OUTPUT
AUDIO
OUTPUT
ADVANCED
OPERATION
O
OPTICAL
OUTPUT
DVD player
Video monitor
INPUT
VOLUME
INPUT M0DE
PRESET/TUNING
ADDITIONAL
INFORMATION
6CH INPUT
FM/AM
EDIT
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
TREBLE
VIDEO AUX
A/B/C/D/E
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
APPENDIX
–
OPTICAL
(RX-V630RDS)
indicates signal direction
VIDEO
OUTPUT
Game console or
camcorder
indicates left analog cables
R
indicates right analog cables
O
indicates optical cables
V
indicates video cables
O
OPTICAL
OUTPUT
15
0103V630_9-18_EN(GB)
15
1/11/02, 7:40 PM
English
V
L
CONNECTIONS
y
Connecting audio components
• The AUDIO jacks are available for an CD recorder or MD
recorder which does not have optical digital input or output
jack.
■ Connecting a CD player
Connect the coaxial digital output jack on your CD player
to the DIGITAL INPUT CD jack.
Notes
• Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
• DIGITAL OUTPUT jack and analog OUT (REC) jacks are
independent. Only digital signals are output from DIGITAL
OUTPUT jack and analog signals from OUT (REC) jacks.
y
• The AUDIO jacks are available for a CD player which does not
have coaxial digital output jack.
■ Connecting a CD recorder or MD
recorder
■
Connect the optical digital signal input jack on your CD
recorder or MD recorder to the DIGITAL OUTPUT MD/
CD-R jack for digital recording.
Connect the optical digital output jack on your CD
recorder or MD recorder to the DIGITAL INPUT MD/
CD-R jack to play a source from your recording
component.
Connecting a tuner
DSP-AX630SE
Connect the output jacks on your tuner to the TUNER
jacks.
DSP-AX630SE
AUDIO
OUTPUT
L
R
Tuner
AUDIO
DIGITAL
INPUT
COAXIAL
OUTPUT
R
AUDIO
L
VIDEO
L
R
S VIDEO
VCR 2
/VDR
CD
C
IN
CD
COAXIAL
OPTICAL
D-TV/CBL
CD player
OPTICAL
OUTPUT
VIDEO
OUT
TUNER
OUT
VCR 1
DVD
OUT
(REC)
MD
/CD-R
IN
(PLAY)
MD/CD-R
MAIN
D-TV
/CBL
SURROUND
DVD
IN
O
O
CD recorder or
MD recorder
OPTICAL
INPUT
SUB
WOOFER
MD/CD-R
OPTICAL
SUB
WOOFER CENTER
DIGITAL
OUTPUT
6CH INPUT
S VIDEO
OUTPUT
VIDEO
MONITOR OUT
(DSP-AX630SE)
indicates signal direction
L
indicates left analog cables
R
indicates right analog cables
C
indicates coaxial cables
O
indicates optical cables
16
0103V630_9-18_EN(GB)
16
1/11/02, 7:40 PM
CONNECTIONS
Connecting the antennas
RX-V630RDS
■ Connecting the AM loop antenna
Set up the AM loop antenna, then connect it.
2
Press and hold the tab to insert the AM loop
antenna lead wires into the AM ANT and
GND terminals.
3
Orient the AM loop antenna for the best
reception.
Connect each antenna correctly to the designated
terminals.
AM loop antenna
(included)
Indoor FM
antenna
(included)
EO
VIDEO
TUNER
AM
ANT
PREPARATION
1
INTRODUCTION
Both AM and FM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength.
GND
DVD
75
UNBAL.
BASIC OPERATION
D-TV
/CBL
FM
ANT
MONIT
OUT
VIDEO
R OUT
Ground (GND terminal)
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
11 (7/16)
8 (5/16)
6 (1/14)
Cut the external sleeve
of the 75-ohm coaxial
cable and prepare it for
connection.
A properly installed outdoor antenna provides clearer
reception than an indoor one. If you experience poor
reception quality, an outdoor antenna may improve the
quality. Consult the nearest authorized YAMAHA
dealer or service center about the outdoor antennas.
3
Lead wire
ADDITIONAL
INFORMATION
Open the cover of the
included 75-ohm/300-ohm
antenna adapter.
Unit:
mm (inch)
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
ADVANCED
OPERATION
Notes
75-ohm/300-ohm antenna adapter (U.K. model)
1
2
Cut the lead wire and
remove it.
Clamp
with
pliers.
APPENDIX
4
5
Clamp with
pliers.
Insert the wire
into the slot.
Snap the cover into
place.
English
Insert the cable wire into the
slot, and clamp it with pliers.
17
0103V630_9-18_EN(GB)
17
1/11/02, 7:40 PM
CONNECTIONS
Connecting an external amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the OUTPUT jacks as follows.
Note
• When RCA pin plugs are connected to the OUTPUT jacks for
output to an external amplifier, signals are output from the
SPEAKERS terminals as well.
1
2
3 4
Connecting an external decoder
This unit is equipped with 6 additional input jacks (MAIN
left and right, CENTER, SURROUND left and right, and
SUBWOOFER) for discrete multi-channel input from an
external decoder, sound processor, or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
OUTPUT
SUB
WOOFER
L
R
MAIN
REAR
CENTER
CENTER
OUTPUT
R
REAR
(SURROUND)
L
5
• When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
• When you select 6CH INPUT as the input source, settings of
“1 SPEAKER SET” on the SET MENU do not apply (except
for “1F MAIN Lv”).
1 SUBWOOFER jack
When using a subwoofer with built-in amplifier,
including the YAMAHA Active Servo Processing
Subwoofer System, connect the input jack of the
subwoofer system to this jack. Low bass signals
distributed from the main, center and/or rear channels are
directed to this jack in accordance with your SPEAKER
SET selections. The LFE (low-frequency effect) signals
generated when Dolby Digital or DTS is decoded are also
directed to this jack in accordance with your SPEAKER
SET selections.
Notes
• The cut-off frequency of the SUBWOOFER jack is 90 Hz.
• If you do not use a subwoofer, designate the signals to the main
left and right speakers by changing the settings of SPEAKER
SET item “1E BASS” on the SET MENU.
• Use the control on the subwoofer to adjust its volume level. It
is also possible to adjust the volume level by using this unit’s
remote control (see “ADJUSTING THE LEVEL OF THE
EFFECT SPEAKERS” on page 51).
2 MAIN jacks
Main channel line output jacks.
Note
• The signals output through these jacks are affected by the
BASS and TREBLE settings.
3 REAR CENTER jack
Rear center channel line output jack.
4 CENTER jack
Center channel line output jack.
5 REAR (SURROUND) jacks
Rear channel line output jacks.
18
0103V630_9-18_EN(GB)
18
1/11/02, 7:40 PM
CONNECTIONS
Connecting the power supply
cords
Turning on the power
1
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
INTRODUCTION
When all connections are complete, turn on the power of
this unit.
AUTO/MAN'L MONO MAN'L/AUTO FM
AC OUTLETS
SWITCHED
100W MAX. TOTAL
BASS
SILENT
TREBLE
SPEAKERS
A
B
VIDEO AUX
STEREO
PROGRAM
A/B/C/D/E
PRESET/TUNING
EFFECT
SYSTEM
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR1/DVR
A
AMP
POWER
+
+
+
TV VOL
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
1
–
MUTE
HALL
1
JAZZ CLUB
ROCK
CONCERT
ENTERTAINMENT
Press STANDBY/ON (SYSTEM POWER on
the remote control) to turn on the power of
this unit.
SYSTEM
POWER
STANDBY
/ON
or
Front panel
Remote control
The level of the main volume, and then the current
DSP program name appear on the front panel
display.
2
ADDITIONAL
INFORMATION
Turn on the video monitor connected to this
unit.
ADVANCED
OPERATION
U.S.A., Canada, China, Europe, Singapore and
General models .............................................. 2 OUTLETS
U.K. and Australia model ................................ 1 OUTLET
Use these outlets to connect the power cords from your
components to this unit. The power to the AC OUTLETS
is controlled by this unit’s STANDBY/ON (or SYSTEM
POWER and STANDBY). These outlets will supply
power to any source component connected to this unit
whenever this unit is turned on. The maximum power
(total power consumption of components) that can be
connected to the AC OUTLETS varies depending on the
area which it was purchasing.
China and General models ......................................... 50 W
Other models ........................................................... 100 W
STANDBY
POWER
Plug in this unit to the wall outlet.
■ AC OUTLETS (SWITCHED)
+
BASIC OPERATION
■ Connecting the AC power cord
–
TRANSMIT
CODE SET
(Europe model)
+
PREPARATION
–
PHONES
APPENDIX
English
19
0104V630_19-22_EN(GB)
19
1/15/02, 5:25 PM
SPEAKER MODE SETTINGS
This unit has 6 SPEAKER SET items on the SET MENU that you must set according to the number of speakers in your
configuration and their size. The following table summarizes these SPEAKER SET items, and shows the initial settings
as well as other possible settings.
If the initial settings shown in the following table are not appropriate for your speaker configuration,
see “1 SPEAKER SET” on pages 43-45 to change the settings.
Summary of SPEAKER SET items 1A through 1F
Item
Description
Possible settings (default
setting indicated in bold)
1A CENTER
Sets center speaker availability and size.
LRG/SML/NON
1B MAIN
Sets main speaker size.
LARGE/SMALL
1C REAR LR
Sets rear L/R speakers availability and size.
LRG/SML/NON
1D REAR CT
Sets rear center speaker availability and size.
LRG/SML/NON
1E BASS
Sets the speaker(s) to be used to output low bass signals.
1F MAIN Lv
Sets the main speaker level.
SWFR/MAIN/BOTH
Nrm (Normal)/–10 dB
20
0104V630_19-22_EN(GB)
20
1/11/02, 7:40 PM
ADJUSTING SPEAKER OUTPUT LEVELS
INTRODUCTION
This section explains how to adjust speaker output levels
using the test tone generator. When this adjustment is
complete, the output level heard at the listening position
should be the same from each speaker. This is important
for best performance of the digital sound field processor,
and the various decoders (Dolby Digital, Dolby Pro
Logic, Dolby Pro Logic and DTS).
Using the test tone
Use the test tone to balance the output levels of the
speakers. The adjustment of each speaker output level
should be made at your listening position using the
remote control.
3
Note
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
Before you begin
BASS
SILENT
TREBLE
SPEAKERS
A
B
VIDEO AUX
STEREO
PROGRAM
A/B/C/D/E
PRESET/TUNING
EFFECT
–
PHONES
INPUT
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
PREPARATION
• Since this unit cannot enter the test mode while headphones are
connected to this unit, be sure to unplug the headphones from
the PHONES jack when using the test tone.
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
FM/AM
AMP
VCR 1
VCR2/DVR
+
+
+
TV CH
VOLUME
A
EDIT
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
TREBLE
SPEAKERS
SILENT
A
VIDEO AUX
PROGRAM
STEREO
B
PRESET/TUNING
TV VOL
A/B/C/D/E
EFFECT
–
PHONES
+
–
+
BASIC OPERATION
PRESET/TUNING
STANDBY
/ON
S VIDEO
VIDEO
L
AUDIO
R
–
–
TV MUTE
TV INPUT
–
1
3
OPTICAL
MUTE
HALL
1
4
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
9
EFFECT
4
2,5
SPEAKERS
A
B
–
MENU
+
SELECT
TEST
DISPLAY
RETURN
2
Press TEST to output the
test tone.
AMP
TEST
RETURN
TREBLE
+
–
+
VOLUME
+
or
VOLUME
–
Front panel
APPENDIX
Adjust the volume of this unit so you can
hear the test tone.
The test tone is heard (in order) from the main left
speaker, center speaker, main right speaker, rear right
speaker, rear center, rear left speaker, and the
subwoofer. The tone is produced for 2.5 seconds
from each speaker.
ADDITIONAL
INFORMATION
Press AMP.
3
–
SET MENU
A/B/C/D/E
1
Set the BASS and TREBLE controls on the
front panel to the center position.
BASS
PRESET/CH
TITLE
ADVANCED
OPERATION
2
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of the
main speakers, press both A
and B.
ENTERTAINMENT
3
MOVIE
THEATER 1
LEVEL
1
ROCK
CONCERT
2
MONO
MOVIE
/DTS
SUR.
2
JAZZ CLUB
1
TV
SPORTS
Remote control
English
21
0104V630_19-22_EN(GB)
21
1/11/02, 7:40 PM
ADJUSTING SPEAKER OUTPUT LEVELS
LEFT
RIGHT
4
CENTER
*SUBWOOFER
Adjust the level of the
effect speakers using j / i
so that it matches the
level of the main
speakers.
While adjusting, the test tone
is heard from the selected
speaker.
PRESET/CH
–
SELECT
+
Note
LEFT SURROUND
RIGHT SURROUND
• To adjust the level of the main speakers, use VOLUME knob
(or VOLUME +/– on the remote control).
5
REAR CENTER
* Subwoofer test tone is output after the rear left
speaker (LEFT SURROUND).
The front panel display shows which speaker is
outputting the test tone.
Note
• If the test tone cannot be heard, turn down the volume, set this
unit to standby mode and check the speaker connections.
When adjustment is
complete, press TEST to
stop the test tone.
TEST
RETURN
Notes
• If “1A CENTER” on the SET MENU is set to NON, the center
channel sound is automatically output from the main left and
right speakers.
• If “1C REAR LR” on the SET MENU is set to NON, the
output level of the rear left, right and center speakers cannot be
adjusted in step 4. The test tone will be circulated skipping the
rear left and right speakers and the rear center speaker.
• If “1D REAR CT” on the SET MENU is set to NON, the
output level of the rear center speaker cannot be adjusted in
step 4. The test tone will be circulated skipping the rear center
speaker.
• If “1E BASS” on the SET MENU is set to MAIN, the test tone
will be circulated skipping the subwoofer.
y
• It is not necessary to readjust the speaker levels once they are
set (as long as you do not change the speakers). You can enjoy
listening to or watching the input source at the desired volume
simply by adjusting the VOLUME knob (or VOLUME +/– on
the remote control).
• If the output level of the effect speakers (center, rear left, rear
right, and rear center) cannot be increased enough to match the
level of the main speakers, set “1F MAIN Lv” on SET MENU
to –10 dB (see page 45). This setting decreases the main
speaker output level to about one-third of the normal level.
After you have set “1F MAIN Lv” on the SET MENU to
–10 dB, adjust the levels for the center and rear speakers again.
22
0104V630_19-22_EN(GB)
22
1/11/02, 7:40 PM
BASIC PLAYBACK
4
6 4
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
4
Press INPUT l / h repeatedly (one of the
input selector buttons on the remote control)
to select the input source.
The selected input source name and input mode
appear on the front panel display for a few seconds.
AUTO/MAN'L MONO MAN'L/AUTO FM
CD
BASS
SILENT
A
B
MD/CD-R
TUNER
DVD
D-TV/CBL
V-AUX
VCR 1
VCR2/DVR
TREBLE
SPEAKERS
VIDEO AUX
STEREO
PROGRAM
A/B/C/D/E
PRESET/TUNING
INTRODUCTION
1
INPUT
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
or
6
7
Front panel
PREPARATION
3
Remote control
TRANSMIT
CODE SET
SYSTEM
POWER
POWER
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
1
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
4
4
L
+
+
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
Selected input source
MUTE
JAZZ CLUB
ROCK
CONCERT
ENTERTAINMENT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
/DTS
SUR.
9
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
7
EFFECT
Press STANDBY/ON (SYSTEM POWER on
the remote control) to turn on the power.
STANDBY
/ON
6CH INPUT
6CH INPUT
SYSTEM
POWER
or
or
Front panel
Front panel
Remote control
ADVANCED
OPERATION
1
To select the audio source connected to the 6CH
INPUT jacks
(When combining with a video source)
• You need to select the input to which the video source
component is connected before selecting audio source.
Press 6CH INPUT until “6CH INPUT” appears on the
front panel display.
BASIC
OPERATION
6
+
TV VOL
HALL
R
Remote control
Turn on the video monitor connected to this
unit.
3
Press SPEAKERS A or B
to select the main
speakers to be used.
If you are using two sets of
main speakers, press both A
and B.
SPEAKERS
A
B
Note
• If “6CH INPUT” is shown on the front panel display, no other
source can be played. To select another input source, first press
6CH INPUT to turn off “6CH INPUT” from the front panel
display.
ADDITIONAL
INFORMATION
2
APPENDIX
English
23
0105V630_23-28_EN(GB)
23
1/11/02, 7:40 PM
BASIC PLAYBACK
5
6
Start playback or select a broadcast station
on the source component.
Refer to the operation instructions for the
component.
Adjust the volume to the desired level.
The volume level is displayed digitally.
Example:
–70 dB
Control range: VOLUME MUTE (minimum) to
0 dB (maximum)
The volume level indicator also shows the current
volume level as a bar graph.
If desired, use BASS and TREBLE. These controls
only effect the sound from the main speakers.
■ BGV (background video) function
The BGV function allows you to enjoy video images
from a video source together with sounds from an audio
source. For example, you can enjoy listening to classical
music while having beautiful scenery from a video source
on the video monitor.
Select a source from the video group, then select a source
from the audio group using the input selector buttons on
the remote control. BGV selections cannot be made with
INPUT l / h on the front panel.
CD
VOLUME
MD/CD-R
TUNER
DVD
D-TV/CBL
V-AUX
VCR 1
VCR2/DVR
+
or
VOLUME
–
BASS
–
TREBLE
+
–
■ To mute the sound
1
Remote control
+
Front panel
MUTE
y
• You can also cancel mute by pressing VOLUME +/–, etc.
• During muting, the “MUTE” indicator flashes on the front
panel display.
Notes
• If you increase or decrease the high-frequency or the lowfrequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the main left
and right speakers.
• If you have connected a recording component to the VCR 1
OUT, VCR 2/DVR OUT, or MD/CD-R OUT jacks, and you
notice distortion or low volume during playback of other
components, try turning the recording component on.
7
Press MUTE on the
remote control.
To resume the audio output,
press MUTE again.
Select a DSP program if desired.
Use PROGRAM l / h (DSP program buttons on
the remote control) to select a DSP program. See
pages 29 to 33 for details about DSP programs.
When using the remote control, press AMP before
selecting a DSP program.
PROGRAM
or
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
/DTS
SUR.
9
■ When you have finished using
this unit
1
Press STANDBY/ON (STANDBY on the
remote control) to set this unit in the
standby mode.
STANDBY
STANDBY
/ON
or
Front panel
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
EFFECT
Front panel
Remote control
24
0105V630_23-28_EN(GB)
24
1/11/02, 7:40 PM
Remote control
BASIC PLAYBACK
■ Notes on 96-kHz sampling digital
signals
Input modes and indications
Each time you turn on the power of this unit, the input
mode is set according to “8 INPUT MODE” setting on
the SET MENU (see page 47 for details).
1
INPUT MODE
CD
MD/CD-R
TUNER
DVD
D-TV/CBL
V-AUX
VCR 1
VCR2/DVR
or
Front panel
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
DVD
AUTO
L
R
Input mode
AUTO:
ADDITIONAL
INFORMATION
Notes
APPENDIX
• When AUTO is selected, this unit automatically determines the
type of signal. If this unit detects a Dolby Digital or DTS
signal, the decoder automatically switches to the appropriate
setting.
• When playing a disc encoded with Dolby Digital or DTS on
some LD or DVD players, the sound output delays for a
moment when playback resumes after a search because the
digital signal is selected again.
• When playing a LD source that has not been digitally recorded,
the sound may not be output for some LD players. In this case,
set the input mode to ANALOG.
ADVANCED
OPERATION
In this mode, the input signal is selected
automatically as follows:
1) Digital signal
2) Analog signal
DTS:
In this mode, only the digital input signal
encoded with DTS is selected, even if
another signal is input at the same time.
ANALOG: In this mode, only the analog input signal is
selected, even if a digital signal is input at
the same time.
• If the digital output data of the player has been
processed in any way, you may not be able to perform
DTS decoding even if you make a digital connection
between this unit and the player.
• If you play a source encoded with a DTS signal and
set the input mode to ANALOG, this unit may
reproduce the noise of an unprocessed DTS signal. In
this case, connect the source to a digital input jack and
set the input mode to AUTO or DTS.
• If you switch the input mode to ANALOG while
playing a source encoded with a DTS signal, this unit
reproduces no sound.
• If you play a source encoded with a DTS signal with
the input mode set to AUTO;
– This unit automatically switches to the DTSdecoding mode (The “t” indicator lights up) after
having detected the DTS signal. When playback of
the DTS source is completed, the “t” indicator
may flash. While this indicator is flashing, only DTS
source can be played. If you want to play a normal
PCM source soon, set the input mode back to AUTO.
– When the input mode is set to AUTO and a search or
skip operation is performed during playback of a
DTS source, the “t” indicator may flash. If this
status continues for longer than 30 seconds, this unit
will automatically switch from “DTS-decoding”
mode to PCM digital signal input mode. The “t”
indicator will turn off.
BASIC
OPERATION
VCR2/DVR
Remote control
■ Notes on playing DTS-CD/LDs
PREPARATION
Press INPUT MODE (the input selector
button that you have pressed to select the
input source on the remote control)
repeatedly until the desired input mode is
shown on the front panel display.
The digital input jacks of this unit can handle 96-kHz
sampling digital signals. Note the following when 96-kHz
sampling digital signal is input to this unit:
– DSP programs cannot be selected.
– Sound will be output as 2-channel stereo from only the
main left and right speakers. (There may be sound
output from the subwoofer depending on the
SPEAKER MODE settings on the SET MENU.)
Therefore, the level of the effect speakers cannot be
adjusted while listening to such a source.
INTRODUCTION
This unit comes with a variety input jacks. You can select
the type of input signals you desire.
English
25
0105V630_23-28_EN(GB)
25
1/11/02, 7:40 PM
BASIC PLAYBACK
3
Selecting a sound field program
You can enhance your listening experience by selecting a
DSP program. For details about each program, see pages
29 to 33.
INPUT
After selecting the desired program, press
the same button repeatedly to select the
desired sub-program if available.
Example: Pressing MOVIE THEATER 1 repeatedly
switches the sub-program between
“Sci-Fi” and “Spectacle”.
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
FM/AM
ENTERTAINMENT
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
5
BASS
TREBLE
SPEAKERS
SILENT
A
B
/DTS
SUR.
VIDEO AUX
PROGRAM
STEREO
A/B/C/D/E
PRESET/TUNING
6
7
8
SELECT
EX/ES
STEREO
0
+10
9
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
ENTER
OPTICAL
EFFECT
PROGRAM l / h
Program name
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
DIGITAL
TRANSMIT
CODE SET
MOVIE THTR 1
SYSTEM
STANDBY
POWER
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
POWER
DSP
+
+
+
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
9
ENTERTAINMENT
2,3
1
Press AMP.
2
Press one of the DSP program buttons on
the remote control to select the desired
program.
The name of the selected program appears on the
front panel display.
AMP
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
9
RR
Notes
EFFECT
/DTS
SUR.
C R
• There are 9 programs with sub-programs available with this
unit. However, the selection depends on the input signal format
and not all sub-programs can be used with all input signal
formats.
• The digital sound field processor cannot be used when a source
connected to the 6CH INPUT jacks of this unit is selected or
when 96-kHz sampling digital signals are input to this unit.
• The acoustics of your listening room affect the DSP program.
Minimize the sound reflections in your room to maximize the
effect created by the program.
• When you select an input source, this unit automatically selects
the last DSP program used with that source.
• When you set this unit in the standby mode, the current source
and DSP program are memorized and are automatically
selected when you turn on the power again.
• If a Dolby Digital or DTS signal is input when the input mode
is set to AUTO, the DSP program (No. 7–9) automatically
switches to the appropriate decoding program.
• When a monaural source is being played with PRO LOGIC/
Normal or PRO LOGIC/Enhanced, or PRO LOGIC Movie,
no sound will be heard from the main speakers and the rear
speakers. Sound can only be heard from the center speaker. (If
“1A CENTER” on the SET MENU is set to NON, the center
channel sound is output from the main speakers.)
MUTE
/DTS
SUR.
L
LFE RL
Sub-program name
1
TV VOL
DGTLzSci-Fi
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
EFFECT
Program name
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
y
CD
VOLUME
DIGITAL
MOVIE THTR 1
DSP
DGTL Spectacle
Sub-program name
L
C R
LFE RL
RR
• You can also select DSP program by pressing PROGRAM
l / h on the front panel.
• Select a program based on your listening preference. Program
names are just for reference.
26
0105V630_23-28_EN(GB)
26
1/11/02, 7:41 PM
BASIC PLAYBACK
■ Selecting PRO LOGIC
4
INPUT
Press SELECT repeatedly to select the
decoder; PRO LOGIC or PRO LOGIC .
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
ENTERTAINMENT
VOLUME
INPUT M0DE
5
6CH INPUT
6
7
8
SELECT
EX/ES
STEREO
0
+10
NATURAL SOUND AV RECEIVER
/DTS
SUR.
PRESET/TUNING
FM/AM
9
ENTER
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
EFFECT
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
TREBLE
SPEAKERS
SILENT
A
B
VIDEO AUX
PROGRAM
STEREO
A/B/C/D/E
PRESET/TUNING
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
5
TRANSMIT
CODE SET
HALL
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
DVD
D-TV/CBL
STANDBY
TUNER
V-AUX
VCR2/DVR
ROCK
CONCERT
ENTERTAINMENT
1
2
3
4
SLEEP
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
6CH INPUT
/DTS
SUR.
VCR 1
JAZZ CLUB
POWER
AMP
A
+
+
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
9
ENTER
EFFECT
–
y
MUTE
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
6
7
8
SELECT
EX/ES
STEREO
0
+10
5
/DTS
SUR.
3,4,5
9
• You can select PRO LOGIC, PRO LOGIC Movie, and PRO
LOGIC Music by pressing PROGRAM l / h on the front
panel repeatedly.
ENTERTAINMENT
ENTER
EFFECT
1
Select a 2-channel source and start playback
on the source component.
2
Press AMP.
3
Press q/DTS SUR.
The previously selected sub program appears on the
front panel display.
AMP
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
9
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
ADDITIONAL
INFORMATION
5
ADVANCED
OPERATION
HALL
/DTS
SUR.
ENTER
EFFECT
Remote control
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
PRO LOGIC
TUNER
CD
VOLUME
PRO LOGIC
L
APPENDIX
PRO LOGIC /
DSP
BASIC
OPERATION
+
TV VOL
2
PREPARATION
PROGRAM l / h
After selecting on the decoder (PRO LOGIC
), select the mode appropriate for the
source by pressing q/DTS SUR.
The selection switches as follow;
PRO LOGIC Movie ↔ PRO LOGIC Music
INTRODUCTION
You can enjoy the 2-channel sources decoded into five or
six discrete channels by selecting PRO LOGIC in
program No. 9.
R
English
27
0105V630_23-28_EN(GB)
27
1/11/02, 7:41 PM
BASIC PLAYBACK
■ Playing Dolby Digital Surround
EX or DTS ES software
■ SILENT CINEMA DSP
Press EX/ES to turn on the Dolby Digital EX or DTS-ES
compatible decoder.
The MATRIX indicator lights up.
EX/ES
+10
MATRIX
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
DIGITAL
MOVIE THTR 1
Spectacle EX
DSP
The display changes AUTO → Matrix6.1 → OFF each
time the EX/ES button is pressed.
AUTO:
Matrix6.1:
OFF:
This mode automatically switches Dolby
Digital EX and DTS-ES compatible
depending on the signal. Rear center speaker
does not work for 5.1 channel sources.
This setting produces 6-channel playback of
the input source using the Dolby Digital EX
or DTS-ES compatible decoder. The rear
center speaker can be used when playing a
5.1-channel source.
Rear center speaker does not work in this
setting. (Except for when the DSP program
“6ch” is selected.)
You can enjoy a powerful sound field similar to what you
could expert from actual speakers with SILENT
CINEMA DSP. You can listen to SILENT CINEMA DSP
by connecting your headphones to the PHONES jack
while the digital sound field processor is on. Enjoy all the
DSP program using the headphones. The “SILENT”
indicator lights up on the front panel display. (When
sound effects are off, you listen to the source with normal
stereo reproduction.)
Notes
• This feature is not available when 6CH INPUT is selected or
96-kHz sampling digital signals are input to this unit.
• The sound of LFE channel will be mixed and output from the
headphone.
■ Normal stereo reproduction
1
Press STEREO to turn off the sound effect
for normal stereo reproduction.
Press STEREO again to turn the sound effect back
on.
STEREO
STEREO
or
ENTER
EFFECT
EFFECT
Front panel
Remote control
Notes
• No sound will be output from the rear center speaker if you
have set “1C REAR LR” or “1D REAR CT” on the SET
MENU to NON.
• The setting becomes AUTO once this unit turns into standby
mode.
• Some Dolby Digital Surround EX or DTS ES software may not
contain the signal that is necessary for this unit to switch to the
Dolby Digital EX or DTS-ES compatible decoding mode. To
turn on the decoder when playing such a source, select
“Matrix6.1”.
■ Virtual CINEMA DSP
With Virtual CINEMA DSP, you can enjoy all DSP
programs without rear speakers. It creates virtual speakers
to reproduce a natural sound field.
You can listen to virtual CINEMA DSP by setting “1C
REAR LR” in the SET MENU to NON. Sound field
processing changes to VIRTUAL CINEMA DSP
automatically.
Note
• This unit is not set in the virtual CINEMA DSP mode even if
“1C REAR LR” is set to NON in the following cases:
– when the 6ch Stereo, DOLBY DIGITAL Normal, Pro Logic
Normal, Pro Logic , or DTS Normal program is selected;
– when the sound effect is turned off;
– when 6CH INPUT is selected as the input source;
– when 96-kHz sampling digital signals are input to this unit;
– when using the test tone; or
– when connecting the headphones.
Notes
• If you turn off the sound effects, no sound is output from the
center speaker, rear speakers, or rear center speaker.
• If you turn off the sound effects while a Dolby Digital or DTS
signal is being output, the dynamic range of the signal is
automatically compressed and the sounds of the center and rear
speaker channels are mixed and output from the main speakers.
• The volume may be greatly reduced when you turn off the
sound effects or if you set “4 D. RANGE” on the SET MENU
to MIN. In this case turn on the sound effect.
• The sound of LFE channel will be directed to the main left and
right or the subwoofer (or both) channels depending on the
setting of “1E BASS” on the SET MENU.
y
During stereo reproduction, you can display information such as
the type, format and sampling frequency of the signal input from
the components connected to this unit.
(While playing a source)
1
2
Press AMP.
Press d to display the information about the
input signal.
PRESET/CH
–
28
0105V630_23-28_EN(GB)
28
1/11/02, 7:41 PM
SELECT
+
DIGITAL SOUND FIELD PROCESSING (DSP)
PREPARATION
A sound field is defined as the “characteristic sound reflections of a
particular space.” In concert halls and other music venues, we hear
early reflections and reverberations as well as the direct sound
produced by the artist(s). The variations in the early reflections and
other reverberations among the different music venues is what gives
each venue its special and recognizable sound quality.
YAMAHA sent teams of sound engineers all around the world to
measure the sound reflections of famous concert halls and music
venues, and collect detailed sound field information such as the
direction, strength, range, and delay time of those reflections. Then
we stored this enormous amount of data in the ROM chips of this
unit.
INTRODUCTION
Understanding sound fields
■ Recreating a sound field
BASIC
OPERATION
Recreating the sound field of a concert hall or an opera house requires localizing the virtual sound sources in your
listening room. The traditional stereo system that uses only two speakers is not capable of recreating a realistic sound
field. YAMAHA’s DSP requires four effect speakers to recreate sound fields based on the measured sound field data.
The processor controls the strength and delay time of the signals output from the four effect speakers to localize the
virtual sound sources and fully encompass the listener.
Hi-Fi DSP programs
No.
Program
ADVANCED
OPERATION
The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in
mind that most of these are precise digital recreations of actual acoustic environments.
Features
A large round concert hall with a rich surround effect. Pronounced reflections from all directions
emphasize the extension of sounds. The sound field has a great deal of presence, and your virtual
seat is near the center, close to the stage.
2
JAZZ CLUB
This is the sound field at stage front in “The Bottom Line”, a famous New York jazz club, that
seats up to 300 people. Its wide left to right seating arrangement offers a real and vibrant sound.
3
ROCK CONCERT
The ideal program for lively, dynamic rock music. The data for this program was recorded at
LA’s “hottest” rock club. The listener’s virtual seat is at the center-left of the hall.
4
ENTERTAINMENT/
Disco
This program recreates the acoustic environment of a lively disco in the heart of a big city. The
sound is dense and highly concentrated. It is also characterized by a high-energy, “immediate”
sound.
ENTERTAINMENT/
6ch Stereo
Using this program increases the listening position range. This is a sound field suitable for
background music at parties, etc.
APPENDIX
CONCERT HALL
ADDITIONAL
INFORMATION
1
English
29
0106V630_29-33_EN(GB)
29
1/11/02, 7:41 PM
CINEMA-DSP
Sound design of CINEMA-DSP
Filmmakers intend for the dialog to be located right on the screen, the effect sound a little farther back, the music spread
even farther back, and the surround sound around the listener. Of course, all of these sounds must be synchronized with
the images on the screen.
CINEMA-DSP is an upgraded version of YAMAHA DSP specially designed for movie soundtracks. CINEMA-DSP
integrates the DTS, Dolby Digital, and Dolby Pro Logic surround sound technologies with YAMAHA DSP sound field
programs to provide a surround sound field. It recreates comprehensive movie sound design in your audio room. In
CINEMA-DSP sound field programs, YAMAHA’s exclusive DSP processing is added to the Main left and right, and
Center channels, so the listener can enjoy realistic dialogue, depth of sound, smooth transition between sound sources,
and a surround sound field that goes beyond the screen.
When a DTS or Dolby Digital signal is detected, the CINEMA-DSP sound field processor automatically chooses the
most suitable sound field program for that signal.
L SURROUND SOUND FIELD
PRESENCE SOUND FIELD
DIALOG
EFFECT
MUSIC
R SURROUND SOUND FIELD
In addition to the DSP, this unit is equipped with a variety of precise decoders; Dolby Pro Logic decoder for Dolby
Surround sources, Dolby Pro Logic decoder for Dolby Surround and 2-channel sources, Dolby Digital/DTS decoder
for multi-channel sources and Dolby Digital EX or DTS-ES compatible decoder for adding a rear center channel. You
can select CINEMA-DSP programs to optimize these decoders and the DSP sound patterns depending on the input
source.
30
0106V630_29-33_EN(GB)
30
1/11/02, 7:41 PM
CINEMA-DSP
■ Dolby Digital/DTS + DSP sound field effect
Left surround DSP
sound field
Right surround DSP
sound field
■ Dolby Digital EX/DTS-ES compatible + DSP sound field effect
■ Dolby Pro Logic + DSP sound field effect
Surround DSP
sound field
ADDITIONAL
INFORMATION
■ Dolby Pro Logic
ADVANCED
OPERATION
Most movie software has 4-channel (left, center, right,
and surround) sound information encoded by Dolby
Surround matrix processing and stored on the left and
right tracks. These signals are processed by the Dolby Pro
Logic decoder. The MOVIE THEATER programs are
designed to recreate the spaciousness and delicate
nuances of sound that tend to be lost in the encoding and
decoding processes.
Presence DSP
sound field
BASIC
OPERATION
These programs provide you with the maximum experience of the spacious surround effects by adding an extra rear
center DSP sound field created from the rear center channel.
PREPARATION
These programs use YAMAHA’s tri-field DSP processing
on each of the Dolby Digital or DTS signals for the front,
left surround, and right surround channels. This
processing enables this unit to reproduce the immense
sound field and surround expression of a Dolby Digitalor DTS-equipped movie theater without sacrificing the
clear separation of all channels.
Presence DSP
sound field
INTRODUCTION
The 6-channel soundtracks found on 70-mm film produce precise sound field localization and rich, deep sound without
using matrix processing. This unit’s MOVIE THEATER programs provide the same quality of sound and sound
localization that 6-channel soundtracks do. The built-in Dolby Digital or DTS decoder brings the professional-quality
sound designed for movie theaters into your home. With this unit’s MOVIE THEATER programs, you can use Dolby
Digital or DTS technology to recreate a dynamic sound that gives you the feeling of being in a public theater.
Dolby Pro Logic decodes Dolby Surround software into 5 discrete full-range channels (3 channels in front and 2
channels in rear). There are 2 modes; MOVIE for movies and MUSIC for 2-channel audio sources.
APPENDIX
English
31
0106V630_29-33_EN(GB)
31
1/11/02, 7:41 PM
CINEMA-DSP
CINEMA-DSP programs
■ For movie programs: No. 7 to 9
This unit automatically chooses the appropriate decoder and DSP sound field pattern according to the input signal
format.
Table of Program Names for Each Input Format
Input
No.
2 channel
5.1 channel
6.1 channel *
Stereo
DOLBY DIGITAL
DTS
DOLBY DIGITAL
EX
DTS-ES
compatible
70 mm Spectacle
DGTL Spectacle
DTS Spectacle
Spectacle EX
Spectacle ES
70 mm Sci-Fi
DGTL Sci-Fi
DTS Sci-Fi
Sci-Fi EX
Sci-Fi ES
70 mm Adventure
DGTL Adventure
DTS Adventure
Adventure EX
Adventure ES
70 mm General
DGTL General
DTS General
General EX
General ES
—
Normal
—
Dolby D EX
—
—
Enhanced
—
Enhanced EX
—
—
—
Normal
—
DTS-ES
—
—
Enhanced
—
Enhanced ES
Normal
—
—
—
—
Enhanced
—
—
—
—
Movie
—
—
—
—
Music
—
—
—
—
Program
7
8
9
MOVIE
THEATER 1
MOVIE
THEATER 2
DOLBY
DIGITAL
DTS DIGITAL
SUR
PRO LOGIC
PRO LOGIC
* means the Dolby Digital EX decoder or the DTS-ES compatible decoder is ON.
y
• If a Dolby Digital signal or DTS signal is input when the input mode is set to AUTO, the DSP program will automatically switch to
the Dolby Digital playback sound field or DTS playback sound field.
• If Dolby Digital Surround EX software or DTS ES software is played when AUTO is selected by pressing the EX/ES button on the
remote control, the Dolby Digital EX or DTS-ES compatible decoder usually turns on and the corresponding DSP program is
selected.
• EX/ES on the remote control can be used to play Dolby Digital or DTS 5.1 channel sources with the rear center speaker. In this case
the program name changes to the corresponding name for 6.1 channel.
• When playing a 6.1 channel source with the Dolby Digital EX decoder or the DTS-ES compatible decoder turned off, the program
name changes to the corresponding name for 5.1 channel.
Notes
• The “
” indicator does not light up when selecting program No. 9 except in Enhanced mode.
• When playing a monaural source with a CINEMA DSP program, the source signal is directed to the center channel, main and rear
speakers output effect sounds.
32
0106V630_29-33_EN(GB)
32
1/11/02, 7:41 PM
CINEMA-DSP
The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in
mind that most of these are precise digital recreations of actual acoustic environments. Select the DSP program that you
feel sounds best regardless of the name and description given for it below.
7
This program creates the extremely wide sound field of a 70-mm movie theater. It
precisely reproduces the source sound in detail, making both the video and the sound
field incredibly real. This is ideal for any kind of video source encoded with Dolby
Surround, Dolby Digital or DTS (especially large-scale movie productions).
Sci-Fi
This program clearly reproduces dialog and sound effects in the latest sound form of
science fiction films, thus creating a broad and expansive cinematic space amid the
silence. You can enjoy science fiction films in a virtual-space sound field that includes
Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced
techniques.
Adventure
This program is ideal for precisely reproducing the sound design of the newest 70-mm
and multichannel soundtrack films. The sound field is made to be similar to that of the
newest movie theaters, so the reverberations of the sound field itself are restrained as
much as possible.
General
This program is for reproducing sounds from 70-mm and multichannel soundtrack films,
and is characterized by a soft and extensive sound field. The presence sound field is
relatively narrow. It spatially spreads all around and toward the screen, restraining the
echo effect of conversations without losing clarity.
Enhanced Mode
■ For audio-video sources: No. 4 to 6
No.
Features
This program adds a deep and spatial feeling to video game sounds.
ENTERTAINMENT/
Concert Video
This program adds a deep and spatial feeling to concert video sounds.
5
TV SPORTS
With this program, you can enjoy watching various TV programs such as news, variety shows,
music programs or sports programs. In a stereo broadcast of a sports game, the commentator is
oriented at the center position, and the shouts and the atmosphere in the stadium spread on the
surround side, while their spread to the rear is properly restrained.
6
MONO MOVIE
This program is provided for reproducing monaural video sources (such as old movies). The
program produces the optimum reverberation to create sound depth by using only the presence
sound field.
APPENDIX
ENTERTAINMENT/
Game
ADDITIONAL
INFORMATION
4
Program
ADVANCED
OPERATION
This program ideally simulates the multi-surround speaker systems of the 35-mm film
theaters. Dolby Pro Logic decoding, Dolby Digital decoding or DTS decoding and digital
sound field processing create precise effects without altering the original sound
orientation.
The surround effects produced by this sound field wrap around the viewer naturally from
the back to the left and right, and toward the screen.
BASIC
OPERATION
9
MOVIE
THEATER 2
Spectacle
PREPARATION
8
Features
Program
MOVIE
THEATER 1
INTRODUCTION
No.
English
33
0106V630_29-33_EN(GB)
33
1/11/02, 7:41 PM
TUNING
4
Automatic and manual tuning
There are 2 ways to tune; automatic and manual.
Automatic tuning is effective when station signals are
strong and there is no interference.
Press PRESET/TUNING l / h once to begin
automatic tuning.
Press h to tune in to a higher frequency, or press l
to tune in to a lower frequency.
PRESET/TUNING
/DVR
■ Automatic tuning
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
TUNED
A
AM
144O
1
INPUT
When tuned in to a station, the “TUNED” indicator
lights up and the frequency of the received station is
shown on the front panel display.
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
y
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
A
B
• Use the manual tuning method if the tuning search does not
stop at the desired station because the signal is weak.
TREBLE
SPEAKERS
SILENT
VIDEO AUX
STEREO
PROGRAM
PRESET/TUNING
A/B/C/D/E
EFFECT
–
PHONES
+
–
4
1
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
■ Manual tuning
If the signal from the station you want to select is weak,
you must tune in to it manually.
33 2
1
Select TUNER and the reception band
following steps 1 and 2 described in
“Automatic tuning” at left.
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator goes off from
the front panel display.
Press INPUT l / h (TUNER on the remote
control) to select TUNER as the input source.
SYSTEM
INPUT
or
STANDBY
POWER
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
POWER
POWER
TV
AV
CD
TUNING MODE
Front panel
AUTO
AUTO/MAN'L MONO
Goes off
If the colon (:) appears on the front panel display,
press PRESET/TUNING (EDIT) to turn it off.
Remote control
2
Press FM/AM to select the reception band.
“FM” or “AM” appears on the front panel display.
PRESET/TUNING
/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
TUNED
FM/AM
EDIT
or
3
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator lights up on the
front panel display.
3
A
AM
144O
Press PRESET/TUNING l / h to tune in to
the desired station manually.
Hold down the button to
continue the tuning search.
PRESET/TUNING
TUNING MODE
AUTO
Lights up
AUTO/MAN'L MONO
Note
If the colon (:) appears on the front panel display,
press PRESET/TUNING (EDIT) to turn it off.
/DVR
PRESET/TUNING
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
• Manually tuning in to an FM station will automatically change
the reception mode to monaural to increase the signal quality.
TUNER
TUNED
EDIT
A
AM
144O
34
0107V630_34-41_EN(GB)
34
1/11/02, 7:42 PM
TUNING
Notes
Presetting stations
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
SILENT
TREBLE
SPEAKERS
A
VIDEO AUX
STEREO
B
PROGRAM
PRESET/TUNING
A/B/C/D/E
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
1
Press FM/AM to select the FM band.
FM/AM
2
TUNING MODE
AUTO
AUTO/MAN'L MONO
3
Lights up
ADDITIONAL
INFORMATION
Press and hold MEMORY (MAN’L/AUTO FM)
for more than 3 seconds.
The preset number and the “MEMORY” and
“AUTO” indicators flash. Then, after about
5 seconds, automatic preset tuning begins from the
frequency currently displayed toward the higher
frequencies.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again.
ADVANCED
OPERATION
Press TUNING MODE (AUTO/MAN’L MONO)
so that the “AUTO” indicator lights up on the
front panel display.
BASIC
OPERATION
23 1
Automatic preset tuning options
You can select the preset number from which this unit
will store FM stations and/or begin tuning toward lower
frequencies. After pressing MEMORY in step 3:
1. Press A/B/C/D/E and PRESET/TUNING l / h to
select the preset number under which the first station
will be stored. Automatic preset tuning will stop when
stations have all been stored up to E8.
2. Press PRESET/TUNING (EDIT) to turn off the colon
(:) and then press PRESET/TUNING l to begin
tuning toward lower frequencies.
PREPARATION
You can use the automatic preset tuning feature to store
FM stations. This function enables this unit to
automatically tune in to FM stations with strong signals,
and to store up to 40 (8 stations x 5 groups) of those
stations in order. This feature enables you to easily tune in
to any preset station by selecting the preset station
number (see page 37).
INTRODUCTION
■ Automatically presetting stations
(for FM stations)
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• When a station data is stored under a preset number, the
frequency and reception band are also stored.
• You can manually replace a preset station with another FM or
AM station by simply following the procedure in the section
“Manually presetting stations” on page 36.
• If the number of the received stations does not reach E8,
automatic preset tuning has automatically stopped after
searching all stations.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune in to it manually
in the monaural mode, and store it by following the procedure
in “Manually presetting stations” on page 36.
MEMORY
MAN'L/AUTO FM
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
AUTO
MEMORY
A1:FM
APPENDIX
VCR2/DVR
CD
VOLUME
L
R
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
English
35
0107V630_34-41_EN(GB)
35
1/11/02, 7:42 PM
TUNING
■ Manually presetting stations
4
You can also store up to 40 stations (8 stations x 5
groups) manually.
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
Press PRESET/TUNING l / h to select a
preset station number (1 to 8) while the
“MEMORY” indicator is flashing.
Press h to select a higher preset station number.
Press l to select a lower preset station number.
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
BASS
TREBLE
SPEAKERS
SILENT
A
B
VIDEO AUX
STEREO
PROGRAM
PRESET/TUNING
A/B/C/D/E
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
TUNED MEMORY
4 3
1
C3:AM 63O kHz
2,5
5
Tune in to a station.
See page 34 for tuning instructions.
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
TUNED
A AM
63O kHz
L
R
When tuned in to a station, the front panel display
shows the frequency of received station.
2
L
R
Press MEMORY (MAN’L/AUTO FM) on the
front panel while the “MEMORY” indicator is
flashing.
MEMORY
The station band and
MAN'L/AUTO FM
frequency appear on the front
panel display with the preset
group and number you have
selected.
Press MEMORY (MAN’L/AUTO FM).
The “MEMORY” indicator flashes for about
5 seconds.
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
TUNED
C3:AM 63O kHz
L
R
Shows the displayed station has been stored as C3.
MEMORY
MEMORY
MAN'L/AUTO FM
6
Repeat steps 1 to 5 to store other stations.
Flashes
Notes
3
Press A/B/C/D/E repeatedly to select a preset
station group (A to E) while the “MEMORY”
indicator is flashing.
The group letter appears and make sure that the
colon (:) appears on the front panel display.
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
A/B/C/D/E
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
VOLUME
TUNED MEMORY
C :AM
63O kHz
L
R
36
0107V630_34-41_EN(GB)
36
1/11/02, 7:42 PM
TUNING
Tuning in to a preset station
Exchanging preset stations
INPUT
You can exchange the assignment of two preset stations.
The example below describes the procedure for
exchanging preset station “E1” with “A5”.
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
PRESET/TUNING
FM/AM
AUTO/MAN'L MONO MAN'L/AUTO FM
EDIT
STANDBY
/ON
BASS
SILENT
A
B
TUNING MODE
MEMORY
AUTO/MAN'L MONO MAN'L/AUTO FM
TREBLE
SPEAKERS
VIDEO AUX
STEREO
PROGRAM
PRESET/TUNING
A/B/C/D/E
BASS
–
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
TREBLE
SPEAKERS
SILENT
EFFECT
PHONES
A
OPTICAL
B
VIDEO AUX
STEREO
PROGRAM
PRESET/TUNING
INTRODUCTION
You can tune any desired station simply by selecting the
preset station number under which it was stored.
A/B/C/D/E
EFFECT
–
PHONES
1,3 1,3
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
PREPARATION
2 1
+
2,4
EFFECT
LEVEL
PRESET/CH
SET MENU
1
2
MENU
TITLE
A/B/C/D/E
–
+
SELECT
TEST
DISPLAY
RETURN
Tune in to preset station “E1” by using the
A/B/C/D/E and PRESET/TUNING l / h.
See “Tuning in to a preset station” at left.
2
Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the “MEMORY” indicator flash on the
front panel display.
AUDIO
DISC SKIP
1
Press A/B/C/D/E (A/B/C/D/E on the remote
control) to select the preset station group.
The preset group letter appears on the front panel
display and changes each time you press A/B/C/D/E.
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
TUNED MEMORY
EDIT
E1:FM 87.5
MHz
SET MENU
A/B/C/D/E
or
MENU
Front panel
Remote control
Press PRESET/TUNING l / h (PRESET
u / d on the remote control) to select a
preset station number (1 to 8).
The preset group and number appear on the front
panel display along with the station band, frequency
and the “TUNED” indicator lights up.
VCR2/DVR
SELECT
Front panel
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
A5:FM 9O.6 MHz
+
L
R
Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
PRESET/TUNING
MEMORY
Remote control
EDIT
EDIT E1-A5
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
APPENDIX
Shows the exchange of stations has
been completed.
VCR2/DVR
CD
TUNED
E1:FM 87.5
ADDITIONAL
INFORMATION
–
V-AUX
VOLUME
PRESET/TUNING
or
VCR1
TUNED MEMORY
4
PRESET/CH
Tune in to preset station “A5” by using the
A/B/C/D/E and PRESET/TUNING l / h.
“A5” and the “MEMORY” indicator flash on the
front panel display.
ADVANCED
OPERATION
3
A/B/C/D/E
2
VCR2/DVR
PRESET/TUNING
BASIC
OPERATION
1
REC
MHz
English
37
0107V630_34-41_EN(GB)
37
1/11/02, 7:42 PM
RECEIVING RDS STATIONS
RDS (Radio Data System) is a data transmission system by FM stations in many countries.
RDS data contains various information such as PS (Program Service name), PTY (Program Type), RT (Radio Text), CT
(Clock Time), EON (Enhanced Other Networks), etc. The RDS function is carried out among the network stations.
Description of RDS data
This unit can receive, PS, PTY, RT, CT, and EON data
when receiving RDS broadcasting stations.
■ PS (Program Service name)
mode:
The name of the RDS station being received is displayed.
■ PTY (Program Type) mode:
There are 15 program types to classify RDS stations.
NEWS
News
AFFAIRS
Current affairs
INFO
General information
SPORT
Sports
EDUCATE
Education
DRAMA
Drama
CULTURE
Culture
SCIENCE
Science
VARIED
Light entertainment
POP M
Pops
ROCK M
Rock
M.O.R. M
Middle-of-the-road music
(easy-listening)
LIGHT M
Light classics
CLASSICS
Serious classics
OTHER M
Other music
■ RT (Radio Text) mode:
Information about the program (such as the title of the
song, name of the singer, etc.) on the RDS station being
received is displayed by a maximum of 64 alphanumeric
characters, including the umlaut symbol. If other
characters are used for RT data, they are displayed with
under-bars.
■ CT (Clock Time) mode:
The current time is displayed and updated every minute.
If the data are accidentally cut off, “CT WAIT” may
appear.
■ EON (Enhanced Other Networks):
Refer to following page.
Changing the RDS mode
The four modes are available in this unit for displaying
RDS data. When an RDS station is being received, PS,
PTY, RT and/or CT mode indicators that correspond to
the RDS data services offered by the station light up on
the front panel display. Press RDS MODE/FREQ
repeatedly to change the display mode among the RDS
data offered by the transmitting station in the order shown
below.
RDS MODE/FREQ
EON
PTY mode
RT mode
CT mode
RDS mode
OFF
Notes
• When an RDS station is being received, do not press RDS
MODE/FREQ until one or more RDS mode indicators light up
on the front panel display. If you press the button before the
indicators light up on the front panel display, the mode cannot
be changed. This is because this unit has not yet received all of
the RDS data on the station.
• RDS data not offered by the station cannot be selected.
• The RDS data service cannot be utilized by this unit if the
received signal is not strong enough. In particular, the RT mode
requires a large amount of data to be received, so it is possible
that the RT mode may not be displayed even if other RDS
modes (PS, PTY, etc.) are displayed.
• RDS data cannot sometimes be received under poor reception
conditions. If so, press TUNING MODE so that the “AUTO”
indicator goes off from the front panel display. Although the
reception mode is changed to monaural by this operation, when
you change the display to RDS mode, RDS data may be
displayed.
• If the signal strength is weakened by external interference
during the reception of an RDS station, the RDS data service
may be cut off suddenly and “...WAIT” will appear on the front
panel display.
38
0107V630_34-41_EN(GB)
38
PS mode
1/11/02, 7:42 PM
RECEIVING RDS STATIONS
PTY SEEK function
EON function
1
Press PTY SEEK MODE to set this unit in the
PTY SEEK mode.
The program type of the station being received or
“NEWS” flashes on the front panel display.
Note
PTY SEEK
MODE
START
Press PRESET/TUNING l / h to select the
desired program type.
The selected program type appears on the front panel
display.
PRESET/TUNING
Press PTY SEEK START to begin searching
all preset RDS stations.
The selected program type flashes and the “PTY
HOLD” indicator lights up on the front panel display
while searching for stations.
PTY HOLD
Lights up
■ To cancel this function
2
Press EON repeatedly to select the desired
program type (NEWS, INFO, AFFAIRS or
SPORT).
The selected program type name appears on the front
panel display.
RDS MODE/FREQ
EON
• If a preset RDS station of the selected program
type starts broadcasting, this unit will
automatically switch from the program being
currently received to that program. (EON indicator
flashes.)
• When broadcasting of the required program ends,
the previously received station (or another
program on the same station) is recalled.
■ To cancel this function
Press EON repeatedly until no program type name lights
up on the front panel display.
Press PTY SEEK MODE twice.
ADDITIONAL
INFORMATION
• If a station that is broadcasting a program of the
required type is found, this unit stops at that
station.
• If the called station is not the desired one, press
PTY SEEK START again. This unit begins
searching for another station that is broadcasting a
program of the same type.
Make sure that the “EON” indicator lights up
on the front panel display.
If the “EON” indicator does not light up, tune in to
another RDS station so that the “EON” indicator
lights up.
ADVANCED
OPERATION
PTY SEEK
MODE
START
1
BASIC
OPERATION
3
• This function can only be used when an RDS station that offers
the EON data service is being received. When such a station is
being received, the “EON” indicator lights up on the front
panel display.
PREPARATION
Flashes
2
This function uses the EON data service on the RDS
station network. If you simply select the desired program
type (NEWS, INFO, AFFAIRS or SPORT), this unit
automatically searches for all preset RDS stations that are
scheduled to broadcast a program of the required type and
switches from the station being currently received to the
new station when the broadcasts starts.
INTRODUCTION
If you select the desired program type, this unit
automatically searches all preset RDS stations that are
broadcasting a program of the required type.
APPENDIX
English
39
0107V630_34-41_EN(GB)
39
1/11/02, 7:42 PM
SLEEP TIMER
Use this feature to automatically set this unit in the
standby mode after the amount of time you have set. The
sleep timer is useful when you are going to sleep while
this unit is playing or recording a source. The sleep timer
also automatically turns off the external component(s)
connected to AC OUTLET(S).
Canceling the sleep timer
1
The sleep timer can only be set with the remote control.
Press SLEEP repeatedly until “SLEEP OFF”
appears on the front panel display.
After a few seconds, “SLEEP OFF” disappears, the
“SLEEP” indicator goes off and the display returns
to the previous indication.
SLEEP
y
• By connecting a commercially available timer to this unit, you
can also set a wake-up timer. Refer to the operation instructions
of the timer.
y
• The sleep timer setting can also be canceled by setting this unit
in the standby mode by using STANDBY on the remote control
(or STANDBY/ON on the front panel) or by disconnecting the
AC power cord from the AC outlet.
Setting the sleep timer
TRANSMIT
CODE SET
SYSTEM
1
STANDBY
POWER
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
POWER
+
+
+
TV VOL
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
2
–
MUTE
1
Select a source and start playback on the
source component.
2
Press SLEEP repeatedly
to set the amount of time.
Each time you press SLEEP,
the front panel display changes
as shown below.
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
SLEEP
MD/CD-R
TUNER
CD
SLEEP
SLEEP
DSP
PCM
3
12Omin
VOLUME
L
R
The “SLEEP” indicator lights up on the front
panel display soon after the sleep timer has
been set.
The display then returns to the previous indication.
VCR2/DVR
VCR1
V-AUX
D-TV/CBL
DVD
MD/CD-R
TUNER
CD
SLEEP
DSP
PCM
CONCERT HALL
VOLUME
L
R
40
0107V630_34-41_EN(GB)
40
1/11/02, 7:42 PM
RECORDING
1
2
INPUT
VOLUME
INPUT M0DE
6CH INPUT
NATURAL SOUND AV RECEIVER
PRESET/TUNING
FM/AM
EDIT
STANDBY
/ON
TUNING MODE
MEMORY
BASS
SILENT
TREBLE
SPEAKERS
A
B
VIDEO AUX
STEREO
PROGRAM
PRESET/TUNING
A/B/C/D/E
EFFECT
–
PHONES
+
–
+
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
TRANSMIT
CODE SET
2
POWER
STANDBY
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
+
+
+
TV VOL
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
■ Special considerations when
recording DTS software
MUTE
ROCK
CONCERT
ENTERTAINMENT
Turn on the power of this unit and all
connected component.
2
Select the source component you want to
record from.
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
INPUT
or
For LDs, DVDs and CDs encoded with DTS, when your
player is compatible with the DTS format, follow its
operation instruction to make a setting so that the analog
signal will be output from the player.
ADVANCED
OPERATION
1
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
BASIC
OPERATION
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
SYSTEM
POWER
PREPARATION
AUTO/MAN'L MONO MAN'L/AUTO FM
Notes
• Do a test recording before you start an actual recording.
• When this unit is set in the standby mode, you cannot record
between the components connected to this unit.
• The setting of BASS, TREBLE, VOLUME, “5 L/R
BALANCE” on the SET MENU and DSP programs does not
effect the recorded material.
• A source connected to the 6CH INPUT jacks on this unit
cannot be recorded.
• A given input source is not output to the same OUT (REC)
channel. (For example, the signal input from VCR 1 IN is not
output to VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material
may infringe copyright laws.
INTRODUCTION
Recording adjustments and other operations are
performed from the recording components. Refer to the
operation instructions for these components.
■ Timer playback/recording
Remote control
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
This unit can perform playback or recording with an
external timer (not supplied). Refer to the operating
instructions for the component and the timer to be used.
Notes
• Stored data, such as input source, will be reflected when
playback or recording with the timer.
• If you do not want any sound output when recording with a
timer, turn the volume down.
APPENDIX
Memory back-up
The memory back-up circuit prevents the stored data
(input source, volume level, set menu settings and so
on) from being lost even if this unit is disconnected
from the AC outlet. However, if the timer is turned off
for more than one week, the stored data will be lost.
ADDITIONAL
INFORMATION
Front panel
English
41
0107V630_34-41_EN(GB)
41
1/11/02, 7:42 PM
ADVANCED OPERATION
SET MENU
The SET MENU consists of 10 items including the
speaker mode setting. Choose the appropriate item and
adjust or select the values as necessary.
Adjusting the items on the SET
MENU
y
• You can adjust the items on the SET MENU while playing a
source.
■ On the remote control
VCR 1
Items
1
Initial settings
SPEAKER SET
A CENTER
B MAIN
C REAR LR
D REAR CT
E BASS
F MAIN Lv
LRG (large)
LARGE
LRG (large)
LRG (large)
BOTH
Nrm (Normal)
2
LFE LEVEL SP/HP
0 dB
3
SP DLY TIME
CENTER
REAR CNTR
0 ms
3 ms
4
D. RANGE SP/HP
MAX
5
L/R BALANCE
0 dB for L/R
6
HP TONE CTRL BASS/TRBL 0 dB
7
I/O ASSIGN
VCR2/DVR
AMP
A
+
+
+
TV VOL
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
–
MUTE
HALL
JAZZ CLUB
ROCK
CONCERT
ENTERTAINMENT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
9
6
ENTER
EFFECT
LEVEL
3,6
PRESET/CH
SET MENU
MENU
TITLE
A/B/C/D/E
–
SELECT
2
+
TEST
RETURN
DISPLAY
REC
AUDIO
4,5
DISC SKIP
Note
• Some items require extra steps.
1
Press AMP.
2
Press SET MENU to enter
the SET MENU.
AMP
SET MENU
MENU
A (component video input)
[A] DVD
[B] D-TV/CBL
B (optical output)
(1) MD/CDR
C (optical input)
(2) MD/CDR
(3) DVD
(4) D-TV/CBL
D (coaxial input)
(5) CD
8
INPUT MODE
AUTO
9
DISPLAY SET
DIMMER
A/B/C/D/E
3
0
OFF
• In the descriptions for each item from the following page, the
default setting is indicated in bold.
Press u/d repeatedly to
select the item you want
to adjust (1 to 10).
–
SELECT
+
• By pressing SET MENU repeatedly, you can select items in the
same order as when pressing d.
Press j / i once to enter
the setup mode of the
selected item.
The last setting you adjusted
appears on the front panel
display.
Depending on the item, press
u/d to select a sub item.
42
42
PRESET/CH
y
4
10 MEM. GUARD
0108V630_42-47_EN(GB)
1
1/11/02, 7:42 PM
PRESET/CH
–
SELECT
+
PRESET/CH
–
SELECT
+
SET MENU
5
Press j / i repeatedly to
change the setting of the
item.
PRESET/CH
–
+
SELECT
1 SPEAKER SET (speaker mode
settings)
6
Press u/d repeatedly until the menu
disappears or simply press one of the DSP
program group buttons to exit SET MENU.
JAZZ CLUB
ROCK
CONCERT
1
2
3
–
+
SELECT
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
or
5
/DTS
SUR.
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
9
■ 1A CENTER (center speaker
mode)
ENTER
By adding a center speaker to your speaker configuration,
this unit can provide better dialog localization for several
listeners and superior synchronization of sound and
images.
EFFECT
■
DSP-AX630SE
On the front panel
INPUT
VOLUME
INPUT M0DE
6CH INPUT
Choices: LRG (large), SML (small), NON (none)
NATURAL SOUND AV RECEIVER
BASS
TREBLE
SPEAKERS
A
B
VIDEO AUX
STEREO
PROGRAM
–
SET MENU
+
NEXT
EFFECT
–
PHONES
4
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
3 1,2,4
Press NEXT to enter the
SET MENU.
NEXT
2
Press NEXT repeatedly to
select the item you want
to adjust.
3
Press SET MENU –/+
repeatedly to change the
setting.
4
Press NEXT repeatedly until the menu
disappears or simply press PROGRAM
l / h to exit the SET MENU.
NON
Select this if you do not have a center speaker. All of the
center channel signal are directed to the main left and
right speakers.
– SET MENU +
ADDITIONAL
INFORMATION
PROGRAM
NEXT
SML
Select this if you have a small center speaker. The lowfrequency signals (90 Hz and below) of the center
channel are directed to the speakers selected with “1E
BASS”.
ADVANCED
OPERATION
1
+
LRG
Select this if you have a large center speaker. The entire
range of the center channel signal is directed to the center
speaker.
BASIC OPERATION
STANDBY
/ON
SILENT
PREPARATION
HALL
PRESET/CH
Notes
• When 96-kHz sampling digital signals are input to this unit,
some items are not affected.
• When 6CH INPUT is selected as the input source, level
adjustments in items 1A through 1E are not affected.
INTRODUCTION
Use this feature to select suitable output modes for your
speaker configuration.
NEXT
or
APPENDIX
English
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby
mode. However, if the power cord is disconnected
from the AC outlet, or the power supply is cut for
more than one week, the stored data will be lost. If
so, adjust the items again.
43
0108V630_42-47_EN(GB)
43
1/11/02, 7:42 PM
SET MENU
■ 1B MAIN (main speaker mode)
Choices: LARGE, SMALL
LARGE
Select this if you have large main speakers. The entire
range of the main left and right channel signal is directed
to the main left and right speakers.
SMALL
Select this if you have small main speakers. The lowfrequency signals (90 Hz and below) of the main channel
are directed to the speakers selected with “1E BASS”.
■ 1C REAR LR (rear speaker mode)
Choices: LRG (large), SML (small), NON (none)
LRG
Select this if you have large rear left and right speakers or
if a rear subwoofer is connected to the rear speakers. The
entire range of the rear channel signal is directed to the
rear left and right speakers.
SML
Select this if you have small rear left and right speakers.
The low-frequency signals (90 Hz and below) of the rear
channel are directed to the speakers selected with “1E
BASS”.
NON
Select this if you do not have rear speakers.
y
• This unit is set in the virtual CINEMA DSP mode when you
select NON for “1C REAR LR”. In this case, the rear center
speaker will automatically be set to “NON” and the “1D REAR
CT” item will be skipped.
■ 1D REAR CT (rear center speaker
mode)
By adding a rear center speaker to your speaker
configuration, this unit can provide more realistic frontto-back and transitions.
Choices: LRG (large), SML (small), NON (none)
LRG
Select this if you have a large rear center speaker. The
entire range of the rear center channel signal is directed to
the rear center speaker.
SML
Select this if you have a small rear center speaker. The
low-frequency signals (90 Hz and below) of the rear
center channel are directed to the speakers selected with
“1E BASS”.
NON
Select this if you do not have a rear center speaker. All of
the rear center channel signal are directed to the rear left
and right speakers.
■ 1E BASS (LFE/bass out mode)
LFE signals carry low-frequency effects when this unit
decodes a Dolby Digital or DTS signal. Low-frequency
signals are defined as 90 Hz and below. The Lowfrequency signals can be directed to both main left and
right speakers, and the subwoofer (subwoofer can be used
for both stereo reproduction and the DSP program).
Choices: SWFR (subwoofer), MAIN, BOTH
SWFR
Select this if you use a subwoofer. The LFE signals are
directed to the subwoofer.
MAIN
Select this if you do not use a subwoofer. The LFE
signals are directed to the main speakers.
BOTH
The LFE signals are directed to the subwoofer. Lowfrequency signals designated to the main channels in
accordance with other speaker mode settings are directed
to both main speakers and a subwoofer.
Note
• When you select MAIN for “1E BASS”, the low-frequency
signals (90 Hz and below) of the main channel are directed to
the main speakers even if you select SMALL for the main
speaker mode.
44
0108V630_42-47_EN(GB)
44
1/11/02, 7:42 PM
SET MENU
■ 1F MAIN Lv (main level mode)
Choices: Nrm (Normal), –10 dB
Nrm
Select this if you can match the output level of your effect
speakers with that of your main speakers when using the
test tone.
2 LFE LEVEL
Control range:
SPEAKER ............ –20 to 0 dB
HEADPHONE ..... –20 to 0 dB
Initial setting: 0 dB
Press d/u to select the item to be adjusted.
2
Press j to adjust the LFE level.
1
0 to 5 ms
0 to 30 ms
0 ms
3 ms
Press j / i to increase or decrease the delay
of the center and the rear center channel
sounds.
Center speaker image
Note
ADVANCED
OPERATION
1
Control range:
CENTER ..........................
REAR CNTR (center) ......
Initial setting:
CENTER ..........................
REAR CNTR (center) ......
BASIC OPERATION
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel when playing back a
Dolby Digital or DTS signal. The LFE signal carries the
low-frequency special effect sound which is only added to
certain scenes.
Use this feature to adjust the delay of the center and the
rear center channel sounds. This feature works when there
is sound output from the center speakers, with a source
like Dolby Digital or DTS, etc. Ideally, the center speaker
and the rear center speaker should be the same distance
from the main listening position as the left and right
speakers. However, in most home situations, the center
speaker or the rear center speaker are placed in line with
the main speakers or the rear speakers. By delaying the
sound from the center speaker and the rear center speaker,
the apparent distance from the center speaker and the rear
center speaker to the main listening position can be
adjusted to make it seem the same as the distance
between the main left and right speaker, and the rear left
and right speakers to the listening position. Adjusting the
delay time for the center speaker is especially important
for giving depth to the dialogue.
PREPARATION
–10 dB
Select this if you cannot match the output level of your
effect speakers with that of your main speakers when
using the test tone.
3 SP DLY TIME (speaker delay
time)
INTRODUCTION
Change this setting if you cannot match the output level
of the center, rear (L/R), and rear center speakers with the
main speakers because of unusually high-efficiency
performance from the main speakers.
C
L
RL
C
R
RC
RR
ADDITIONAL
INFORMATION
• Adjust the LFE level according to the capacity of your
subwoofer or headphones.
RC
• Increasing the delay by 1 ms simulates moving the speakers
about 30 cm (one foot) farther away from the listening
position.
APPENDIX
y
English
45
0108V630_42-47_EN(GB)
45
1/11/02, 7:42 PM
SET MENU
4 D. RANGE (dynamic range)
Use this feature to adjust the dynamic range. This setting
is effective only when this unit is decoding Dolby Digital
signals.
Choices: MAX, STD (standard), MIN (minimum)
MAX
Select the “MAX” for feature films.
STD
Select the “STD” for general use.
MIN
Select the “MIN” for listening to sources at low volume
levels.
5 L/R BALANCE (balance of the
main left and right speakers)
Use this feature to adjust the balance of the output level
from the main left and right speakers.
Control range: 20 steps for L/R
Initial setting: 0 dB for L/R
1
Press i to decrease the output level for the
main left speaker. Press j for the main right
speaker.
6 HP TONE CTRL (headphone tone
control)
7 I/O ASSIGN (input/output
assignment)
It is possible to assign jacks according to the component
to be used if this unit’s COMPONENT VIDEO input jack
or DIGITAL INPUT/OUTPUT jack settings (component
names for jacks) differ from that component. This makes
it possible to change the jack assignment and effectively
connect more components.
Once you assign, you can select that component with
INPUT l / h (or the input selector buttons on the
remote control).
■ 7A CMPNT-V INPUT for
COMPONENT VIDEO INPUT jacks
[A] and [B]
Choices:
■ 7B OPTICAL OUT for OPTICAL
OUTPUT jack (1)
Choices:
–6 to +3
–6 to +3
0 dB
0 dB
(1) MD/CD-R, ( DSP-AX630SE TUNER),
CD, V-AUX, VCR 2/DVR, VCR 1,
D-TV/CBL, DVD
■ 7C OPTICAL IN for OPTICAL
INPUT jacks (2) to (4)
Choices:
Use this feature to adjust the level of the bass and treble
when you use your headphones.
Control range (dB):
BASS ...............
TRBL (treble) ..
Initial setting:
BASS ...............
TRBL ...............
[A] DVD, V-AUX, VCR 2/DVR, VCR 1,
D-TV/CBL
[B] DVD, V-AUX, VCR 2/DVR, VCR 1,
D-TV/CBL
(2) MD/CD-R, ( DSP-AX630SE TUNER),
CD, VCR 2/DVR, VCR 1, D-TV/
CBL, DVD
(3) MD/CD-R, ( DSP-AX630SE TUNER),
CD, VCR 2/DVR, VCR 1, D-TV/
CBL, DVD
(4) MD/CD-R, ( DSP-AX630SE TUNER),
CD, VCR 2/DVR, VCR 1, D-TV/
CBL, DVD
■ 7D COAXIAL IN for COAXIAL
INPUT jack (5)
Choices:
(5) MD/CD-R, ( DSP-AX630SE TUNER),
CD, V-AUX, VCR 2/DVR, VCR 1, DTV/CBL, DVD
Notes
• You cannot select an item more than once for the same type of
jack.
• When you connect a component to both the COAXIAL and
OPTICAL jacks, priority is given to the input signals from the
COAXIAL jack.
46
0108V630_42-47_EN(GB)
46
1/11/02, 7:42 PM
SET MENU
8 INPUT MODE (initial input
mode)
INTRODUCTION
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn
on this unit (see page 25 for details about the input
mode).
Choices: AUTO, LAST
PREPARATION
AUTO
Select this to allow this unit to automatically detect the
type of input signal and select the appropriate input mode.
LAST
Select this to set this unit to automatically select the last
input mode used for the respective source.
9 DISPLAY SET
BASIC OPERATION
■ DIMMER
You can adjust the brightness of the front panel display.
Control range: –4 to 0
Initial setting: 0
10 MEM. GUARD (memory guard)
ADVANCED
OPERATION
Use this feature to prevent accidental changes to settings
on this unit.
Choices: ON, OFF
ADDITIONAL
INFORMATION
Select ON to protect the following features:
• All SET MENU items
• Center, rear speakers, rear center, and subwoofer
levels
• DSP program parameters
Notes
• When this item is set to ON, you cannot use the test tone.
• When this item is set to ON, you cannot select any other SET
MENU items.
APPENDIX
English
47
0108V630_42-47_EN(GB)
47
1/11/02, 7:42 PM
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can operate other A/V components made by YAMAHA and other
manufacturers. To control other components, you must set up the remote control with the manufacturer codes.
Control area
■ Controlling this unit
■ Controlling other component
The shaded areas below can be used to control this unit
when the AMP mode is selected. Press AMP to select the
AMP mode.
The shaded areas below can be used to control other
components. Each button has a different function
depending on the selected components. Select the
component to be controlled by pressing an input selector
button.
TRANSMIT
CODE SET
SYSTEM
Å button and
input selector
buttons
POWER
TV
AV
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
POWER
TRANSMIT
CODE SET
VCR 1
Press AMP to
control this unit.
STANDBY
POWER
VCR2/DVR
AMP
A
+
+
+
TV VOL
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
ROCK
CONCERT
ENTERTAINMENT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
MUTE
/DTS
SUR.
9
The buttons in the
dotted lines
(SYSTEM
POWER,
STANDBY,
SLEEP, 6CH
INPUT, VOLUME
+/– and MUTE)
function in any
mode.
Å button and input selector
buttons switch the control area
for each component.
* Å button is to operate the
other components that are not
connected to this unit.
Factory setting:
Å...VCR
SYSTEM
STANDBY
POWER
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
POWER
POWER
TV
AV
CD
+
VOLUME
+
TV VOL
–
+–
TV CH
MUTE
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
ENTER
EFFECT
LEVEL
PRESET/CH
SET MENU
A/B/C/D/E
–
SELECT
3
4
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
DISPLAY
RETURN
ENTERTAINMENT
2
MONO
MOVIE
+
TEST
ROCK
CONCERT
1
TV
SPORTS
MENU
TITLE
9
ENTER
EFFECT
REC
LEVEL
AUDIO
DISC SKIP
PRESET/CH
SET MENU
MENU
TITLE
A/B/C/D/E
–
SELECT
+
TEST
RETURN
DISPLAY
REC
AUDIO
DISC SKIP
Component control area
You can control up to 9 different components. You can set up
manufacturer code and program other remote control functions for
each component (see page 50).
48
0109V630_48-53_EN(GB)
48
1/11/02, 7:42 PM
REMOTE CONTROL FEATURES
Setting the manufacturer code
The following table shows factory-set component
(Library: component category) and the manufacturer code
for each component control.
■ Clearing setup manufacturer
code for the component control
1
Press an input selector button or Å to select
the component control for which you want to
clear the manufacturer code.
Code
Component category
(Library)
Manufacturer
CD
CD
YAMAHA
0005
MD/CD-R
MD
YAMAHA
0024
TUNER
TUNER
YAMAHA
0003
DVD
DVD
YAMAHA
0098
D-TV/CBL
–
–
–
V-AUX
–
–
–
–
–
–
–
–
–
A
–
–
–
2
POWER
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
POWER
TV
AV
CD
Press CODE SET by using a ballpoint pen or
similar object.
The TRANSMIT indicator flashes twice.
TRANSMIT
CODE SET
Note
1
CD
MD/CD-R
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
• If you do not press any button within 30 seconds after step 2,
the clearing process is canceled. If this happens, start over from
step 1.
3
Press CODE SET using a ballpoint pen or
similar object.
The TRANSMIT indicator flashes twice.
Enter the code number “0000”.
The TRANSMIT indicator flashes twice, and the
manufacturer code for the selected component is
cleared.
ADVANCED
OPERATION
2
Press an input selector button or Å to select
the component you want to set up.
y
• You can clear all setup manufacturer codes at once by entering
the code number “9990”.
ADDITIONAL
INFORMATION
TRANSMIT
CODE SET
3
Press the numeric buttons to enter the four
digit manufacturer’s code for the component
to be used.
Refer to “LIST OF MANUFACTURER’S CODES”
at the end of this manual.
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
/DTS
SUR.
9
APPENDIX
HALL
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
BASIC OPERATION
VCR 1
VCR 2/DVR
SYSTEM
STANDBY
POWER
PREPARATION
Component
control
(buttons)
INTRODUCTION
You can control other components by setting a
manufacturer code. Codes can be set for each of the 9
component controls.
Clearing setup manufacturer
codes
ENTER
EFFECT
The TRANSMIT indicator flashes twice.
English
Notes
• If the manufacturer of your component has more than one
code, try each of them until you find the correct one.
• If you wait for more than 30 seconds during step 3, the setup
process is canceled. If this happens, start over from step 2.
49
0109V630_48-53_EN(GB)
49
1/11/02, 7:42 PM
REMOTE CONTROL FEATURES
Controlling other components
You can operate other components when you have set the
manufacturer code for your component. Note, however,
that some buttons may not operate your component.
Once you select an input source, the remote control
switches to the mode for operating the component.
TRANSMIT
CODE SET
1
2
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
STANDBY
POWER
TUNER
SLEEP
DVD
D-TV/CBL
V-AUX
6CH INPUT
VCR 1
VCR2/DVR
A
AMP
TV MUTE
TV INPUT
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
MUTE
7
5
/DTS
SUR.
9
3
4
ENTERTAINMENT
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
w
EFFECT
+
+
+
TV VOL
TV CH
VOLUME
–
–
TV MUTE
TV INPUT
8
LEVEL
PRESET/CH
SET MENU
MENU
TITLE
e
A/B/C/D/E
–
9
–
0
RETURN
+
SELECT
TEST
5
6
DVD player
VCR
TV, digital/cable TV
MUTE
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
CD player
ENTERTAINMENT
4
DISPLAY
REC
AUDIO
q
DISC SKIP
CD/MD recorder
Tuner
1 AV POWER
*1Power
*1Power
*3VCR power
*1Power
*1Power
*1Power
2 TV POWER
*2TV power
*2TV power
*2TV power
*2TV power
*2TV power
*2TV power
3 TV CH +
*2TV channel up
*2TV channel up
TV channel up
*2TV channel up
*2TV channel up
*2TV channel up
TV CH –
*2TV channel down
*2TV channel down
TV channel down
*2TV channel down
*2TV channel down
*2TV channel down
4 TV VOL +
*2TV volume up
*2TV volume up
TV volume up
*2TV volume up
*2TV volume up
*2TV volume up
TV VOL –
*2TV volume down
*2TV volume down
TV volume down
*2TV volume down
*2TV volume down
*2TV volume down
*2TV mute
*2TV mute
TV mute
*2TV mute
*2TV mute
*2TV mute
5 TV MUTE
6 TV INPUT
* TV input
* TV input
TV input
* TV input
* TV input
*2TV input
7 1-9, 0, +10
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Preset stations (1-8)
8 TITLE
9 PRESET/CH u
PRESET/CH d
2
Up
VCR channel up
Preset up
VCR channel down
Preset down
Left
Right
q REC/DISC SKIP
2
Down
PRESET/CH i
SELECT
2
Title
PRESET/CH j
0 RETURN
2
Select
Return
Disc skip
Rec
*3VCR rec
Disc skip
Play
Play
*3VCR play
Play
Play
e
Search backward
Search backward
*3VCR search backward
Search backward
Search backward
r
Search forward
Search forward
*3VCR search forward
Search forward
Search forward
Pause
*3VCR pause
w
AUDIO
d
Audio
Pause
t
Skip backward
y
Skip forward
a
w ENTER
e MENU
r DISPLAY
Rec (MD)
Pause
Pause
Skip backward
Skip backward
Skip forward
Skip forward
Stop
Stop
*3VCR stop
Stop
Stop
Title/Index
Enter
Enter
Index
Index
Display
Display
Menu
A/B/C/D/E
Display
*1 This button functions only when the original remote control of the component has POWER button.
*2 These buttons can operate your TV without switching the input if the manufacturer code is set in D-TV/CBL.
*3 These buttons can operate your VCR without switching the input to VCR if the manufacturer code is set in VCR.
50
0109V630_48-53_EN(GB)
50
1/11/02, 7:42 PM
r
ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS
3
Adjustment should be made with the remote control.
Press j / i to adjust the speaker output level.
• The control range for the center or rear left and
right speakers is from +10 dB to –10 dB.
• The control range for the subwoofer is from 0 dB
to –20 dB.
PRESET/CH
TRANSMIT
CODE SET
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
DVD
D-TV/CBL
VCR2/DVR
+
+
POWER
TUNER
SLEEP
MUTE
V-AUX
6CH INPUT
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
AMP
A
HALL
9
1
PRESET/CH
LEVEL
TV VOL
TV CH
VOLUME
–
–
–
TV MUTE
TV INPUT
HALL
JAZZ CLUB
SET MENU
MENU
TITLE
A/B/C/D/E
–
SELECT
+
TEST
DISPLAY
RETURN
MUTE
ROCK
CONCERT
REC
ENTERTAINMENT
AUDIO
2
2
3
DISC SKIP
Press AMP.
AMP
Notes
• When the speaker output modes for “1A CENTER” and “1C
REAR LR” are set to NON, and “1E BASS” to MAIN, the
output level of those speakers cannot be adjusted because there
is no sound coming from these speakers.
• When you adjust the output level with LEVEL, the settings you
made with the test tone will be changed.
• We recommend adjusting the speakers by following the steps
described in “Using the test tone” on pages 21 and 22.
■ For 6ch Stereo
(While playing a source)
2
+
LEVEL
You can adjust the volume level for each channel in 6channel stereo mode.
Control range: 0 to 100%
• CT level (Center level)
• RL level (Rear left level)
• RR level (Rear right level)
• RC level (Rear center level)
ADVANCED
OPERATION
Press LEVEL repeatedly to select the
speaker(s) you want to adjust.
Each time you press LEVEL, the selected speaker
changes and appears on the front panel display as
follows: center, rear right, rear center, rear left and
subwoofer.
TITLE
Rear right speaker output
level
Rear center speaker output
level
Select 6ch Stereo.
3
Press j / i to adjust the speaker output level.
Press u / d repeatedly to select the
speaker(s) you want to adjust.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby
mode. However, if the power cord is disconnected
from the AC outlet, or the power supply is cut for
more than one week, the stored data will be lost. If so,
set the output level again.
Subwoofer output level
APPENDIX
Rear left speaker output
level
1
2
ADDITIONAL
INFORMATION
Center speaker output level
BASIC OPERATION
1
SELECT
ENTER
EFFECT
+
–
ENTERTAINMENT
PREPARATION
VCR 1
STANDBY
INTRODUCTION
You can adjust the output level of each effect speaker
(center, rear left and right, rear center and subwoofer)
while listening to a source.
y
English
• Once you press LEVEL, you can also select the speaker(s) to
be adjusted by pressing d / u.
PRESET/CH
LEVEL
–
TITLE
SELECT
+
51
0109V630_48-53_EN(GB)
51
1/11/02, 7:42 PM
ADJUSTING THE DELAY TIME
You can adjust the time difference between the beginning
of the sound from the main speakers and the beginning of
the sound effect from the rear speakers. The larger the
value, the later the sound effect is generated. The delay
time can be individually adjusted to all DSP programs.
Adjustment should be made with the remote control.
TRANSMIT
CODE SET
SYSTEM
POWER
POWER
TV
AV
CD
MD/CD-R
DVD
VCR 1
1
The following table shows factory-set delay time.
D-TV/CBL
VCR2/DVR
STANDBY
POWER
TUNER
SLEEP
MUTE
V-AUX
6CH INPUT
AMP
A
HALL
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
ENTER
/DTS
SUR.
9
1.
2.
3.
4.
5.
6.
7.
8.
9.
Preset value (ms)
45
30
15
26
36
21
10
69
23
15
15
15
20
15
15
15
20
15
15
15
20
15
15
15
15
5
5
5
20
5
5
5
15
5
+
+
TV CH
VOLUME
–
–
–
LEVEL
PRESET/CH
TV MUTE
MENU
TV INPUT
JAZZ CLUB
52
SELECT
+
TEST
MUTE
HALL
SET MENU
A/B/C/D/E
–
ROCK
CONCERT
ENTERTAINMENT
RETURN
DISPLAY
REC
AUDIO
3
4
DISC SKIP
1
Press AMP.
AMP
(While playing a source)
2
Select a DSP program you want to adjust the
delay time.
3
Press u / d so that “DELAY” appears on the
front panel display.
PRESET/CH
–
4
SELECT
+
DELAY
Press j / i to adjust the delay time.
Notes
• Adding too much delay will cause an unnatural effect with
some sources.
• The sound is momentarily interrupted while adjusting the delay
time.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby
mode. However, if the power cord is disconnected
from the AC outlet, or the power supply is cut for
more than one week, the stored data will be lost. If so,
adjust the delay time again.
52
0109V630_48-53_EN(GB)
2
EFFECT
+
TV VOL
TITLE
Program
CONCERT HALL
JAZZ CLUB
ROCK CONCERT
DISCO
GAME
CONCERT VIDEO
TV SPORTS
MONO MOVIE
70 mm SPECTACLE
DGTL SPECTACLE
DTS SPECTACLE
Spectacle EX/ES
70 mm SCI-FI
Sci-Fi EX/ES
DGTL SCI-FI
DTS SCI-FI
70 mm ADVENTURE
DGTL ADVENTURE
DTS ADVENTURE
Adventure EX/ES
70 mm GENERAL
DGTL GENERAL
DTS GENERAL
General EX/ES
PRO LOGIC/NORMAL
DOLBY DIGITAL/NORMAL
DTS DIGITAL SUR./NORMAL
Dolby D EX/DTS ES
PRO LOGIC/ENHANCED
DOLBY DIGITAL/ENHANCED
DTS DIGITAL SUR./ENHANCED
Enhanced EX/ES
PRO LOGIC Movie
PRO LOGIC Music
ENTERTAINMENT
1/11/02, 7:43 PM
ADJUSTING THE PARAMETER SETTINGS FOR PRO LOGIC
You can adjust the values of PRO LOGIC Music
parameters so the sound fields are recreated accurately in
your listening room.
Adjustments should be made with the remote control.
TRANSMIT
CODE SET
SYSTEM
AV
CD
MD/CD-R
DVD
VCR 1
D-TV/CBL
VCR2/DVR
STANDBY
POWER
TUNER
SLEEP
MUTE
V-AUX
6CH INPUT
JAZZ CLUB
ROCK
CONCERT
1
2
3
4
TV
SPORTS
MONO
MOVIE
MOVIE
THEATER 1
MOVIE
THEATER 2
5
6
7
8
SELECT
EX/ES
STEREO
0
+10
/DTS
SUR.
AMP
A
HALL
9
1
ENTERTAINMENT
2
ENTER
EFFECT
+
+
+
LEVEL
PRESET/CH
TV CH
VOLUME
–
–
–
TV MUTE
TV VOL
TV INPUT
JAZZ CLUB
3
4
A/B/C/D/E
–
+
SELECT
TEST
ROCK
CONCERT
DISPLAY
RETURN
MUTE
HALL
SET MENU
MENU
TITLE
REC
ENTERTAINMENT
AUDIO
• You cannot change parameter values when “10 MEM.
GUARD” on the SET MENU is set to ON.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter value you edited will
return to the factory setting. If so, edit the parameter
value again.
■ PANORAMA
1
Press AMP.
2
Select PRO LOGIC
Function:
AMP
Choices:
9
■ DIMENSION
Function:
Gradually adjusts the soundfield either
towards the front or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
SELECT
0
Press u / d to select the
parameter.
–
Press j / i to change the
parameter value.
+
PRESET/CH
–
SELECT
+
Function:
Adjusts the center image from all three
front speakers to varying degrees. The
larger the value, adjusts the center image
towards the main left and right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from main left and
right speakers), initial setting is 3.
APPENDIX
5
SELECT
ADDITIONAL
INFORMATION
4
■ CT WIDTH (Center width)
PRESET/CH
ADVANCED
OPERATION
/DTS
SUR.
Music.
Turning the function on extends the front
stereo image to include the surround
speakers for wraparound effect.
OFF/ON, initial setting is OFF.
BASIC OPERATION
PRO LOGIC Music parameter
descriptions
DISC SKIP
3
PREPARATION
POWER
TV
INTRODUCTION
Note
Changing parameter settings
POWER
MUSIC
Repeat steps 3 and 4 above as necessary to
change other parameters.
English
53
0109V630_48-53_EN(GB)
53
1/11/02, 7:43 PM
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed
below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact
the nearest authorized YAMAHA dealer or service center.
■ General
Problem
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters in the
standby mode soon
after the power has
been turned on.
No sound.
The picture does not
appear.
Cause
Remedy
The power cord is not connected or the
plug is not completely inserted.
Firmly connect the power cord.
—
The IMPEDANCE SELECTOR switch
on the rear panel is not fully set to either
the left or right position.
Set the switch fully to the left or right position when
this unit is in the standby mode.
12
The protection circuitry has been
activated.
Make sure all speaker wire connections on this unit
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
10, 11
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit in the standby mode, disconnect the
power cord, plug it back in after 30 seconds, then
start operating.
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10 – 16
An appropriate input source has not been
selected.
Select an appropriate input source with INPUT
l / h or 6CH INPUT (or the input selector buttons).
23
The speaker connections are not secure.
Secure the connections.
The main speakers to be used have not
been selected properly.
Select the main speakers with SPEAKERS A and/or
B.
23
The volume is turned down.
Turn up the volume.
24
The sound is muted.
Press MUTE or any operation buttons of this unit to
cancel a mute and adjust the volume.
—
Digital signals which this unit cannot
reproduce are being input to this unit by
playing a CD-ROM, etc.
Play a source whose signals this unit can reproduce.
—
The output and input for the picture are
connected to different types of video
jacks.
Make connections using the same type of video
jacks (S VIDEO, VIDEO (composite), or
COMPONENT VIDEO) for both the input and
output.
54
0110V630_54-60_EN(GB)
Refer
to page
54
1/11/02, 7:43 PM
—
10, 11
14, 15
TROUBLESHOOTING
Problem
Cause
The sound suddenly
goes off.
The protection circuit has been activated
because of a short circuit, etc.
Check the IMPEDANCE SELECTOR switch is set
to the appropriate position and then turn this unit
back on.
12
Check the speaker wires are not touching each other
and then turn this unit back on.
—
The sleep timer has functioned.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE or any operation buttons of this unit to
cancel a mute and adjust the volume.
—
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
10, 11
Incorrect setting of “5 L/R BALANCE”
on the SET MENU.
Adjust it to the appropriate position.
46
The sound effect is off.
Press STEREO/EFFECT to turn it on.
28
A Dolby Surround, Dolby Digital or
DTS decoding DSP program is being
used with material not encoded with
Dolby Surround, Dolby Digital or DTS.
Select another DSP program.
No sound from the
center speaker.
—
Raise the level of the center speaker.
51
“1A CENTER” on the SET MENU is set
to NON.
Select the appropriate mode for your center speaker.
43
One of the Hi-Fi DSP programs (1 to 4)
has been selected (except for 6ch Stereo).
Select another DSP program.
—
The output level of the rear speakers is
set to minimum.
Raise the output level of the rear speakers.
A monaural source is being played with
program 9.
Select another DSP program.
“1E BASS” on the SET MENU is set to
MAIN when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
44
“1E BASS” on the SET MENU is set to
SWFR or MAIN when a 2-channel
source is being played.
Select BOTH.
44
Poor bass
reproduction.
26 – 33
APPENDIX
The source does not contain low bass
signals (90 Hz and below).
51
—
Select MAIN.
44
The speaker mode settings (main, center,
rear, or rear center) on the SET MENU
does not match your speaker
configuration.
Select the appropriate position for each speaker
based on the size of the speakers in your
configuration.
43 – 45
55
0110V630_54-60_EN(GB)
55
1/11/02, 7:43 PM
English
“1E BASS” on the SET MENU is set to
SWFR or BOTH and your system does
not include a subwoofer.
ADDITIONAL
INFORMATION
No sound from the
subwoofer.
26 – 33
ADVANCED
OPERATION
The output level of the center speaker is
set to minimum.
The source encoded with a Dolby Digital
or DTS signal does not have a center
channel signal.
No sound from the
rear speakers.
26 – 33
BASIC
OPERAIONT
A 96-kHz sampling digital signal is
being input to this unit.
PREPARATION
No sound from the
effect speakers.
Refer
to page
INTRODUCTION
Only the speaker on
one side can be
heard.
Remedy
TROUBLESHOOTING
Problem
Cause
No sound from the rear
center speaker.
Remedy
Refer
to page
“1C REAR LR” or “1D REAR CT” on
the SET MENU is set to NON.
Select LRG or SML.
44
The Dolby Digital EX decoder or the
DTS-ES compatible decoder is not on.
Press the EX/ES button on the remote control to
turn it on.
28
A “humming” sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
The volume level
cannot be increased, or
the sound is distorted.
The component connected to the OUT
(REC) jacks of this unit is turned off.
Turn on the power to the component.
The sound effect
cannot be recorded.
It is not possible to record the sound
effect by a recording component.
A source cannot be
recorded by a digital
recording component
connected to the
DIGITAL OUTPUT jack
of this unit.
A source component is not connected to
the DIGITAL INPUT jacks of this unit.
Connect the source component to the DIGITAL
INPUT jacks of this unit.
—
The sound field
parameters and some
other settings on this
unit cannot be
changed.
“10 MEM. GUARD” in the SET MENU
is set to ON.
Set “10 MEM. GUARD” in the SET MENU to
OFF.
—
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cord from the outlet
and then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears on the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected
correctly.
—
There is noise
interference from digital
or high-frequency
equipment, or this unit.
This unit is too close to the digital or
high-frequency equipment.
Move this unit further away from such
equipment.
—
This unit suddenly
turns into the standby
mode.
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait until this unit cools down and then turn it
back on.
—
56
—
—
56
0110V630_54-60_EN(GB)
10 – 16
1/11/02, 7:43 PM
TROUBLESHOOTING
■ Tuner
RX-V630RDS
Problem
Cause
17
Use the manual tuning method.
34
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
—
The desired station
cannot be tuned in with
the automatic tuning
method.
The station is too weak.
Use a high-quality directional FM antenna.
17
Use the manual tuning method.
34
Previously preset
stations can no longer
be tuned in.
This unit has been disconnected for a
long period.
Re-store the stations.
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for best reception.
17
Use the manual tuning method.
34
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
17
There are buzzing and
whining noises
(especially in the
evening).
A TV set is being used nearby.
Move this unit away from the TV.
—
35, 36
BASIC
OPERAIONT
AM
Check the antenna connections.
Try using a high-quality directional FM
antenna.
PREPARATION
FM
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Refer
to page
INTRODUCTION
FM stereo reception is
noisy.
Remedy
ADVANCED
OPERATION
■ Remote control
The remote control
does not work nor
function properly.
Cause
Remedy
Refer to
page
The remote control will function within a
maximum range of 6 m (20 feet) and no more
than 30 degrees off-axis from the front panel.
7
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries with new ones.
3
The manufacture code has not correctly
set.
Set the code correctly.
49
Try setting another code of the same
manufacturer.
—
—
English
Even if the manufacturer code is
correctly set, there are some models that
do not respond to the remote control.
APPENDIX
Wrong distance or angle.
57
0110V630_54-60_EN(GB)
57
1/11/02, 7:43 PM
ADDITIONAL
INFORMATION
Problem
GLOSSARY
■ Dolby Surround
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 main
left and right channels (stereo), a center channel for
dialog (monaural), and a rear channel for special sound
effects (monaural). The rear channel reproduces sound
within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ Dolby Digital
Dolby Digital is a digital surround sound system that
gives you completely independent multi-channel audio.
With 3 front channels (left, center, and right), and 2 rear
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1 channels (LFE is counted as 0.1 channel).
By using 2-channel stereo for the rear speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
Dolby Digital EX creates 6 full-bandwidth output
channels from 5.1-channel sources. This is done using a
matrix decoder that derives 3 surround channels from the
2 in the original recording. For the best results, Dolby
Digital EX should be used with movie sound tracks
recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with “flyover” and “fly-around” effects.
■ Dolby Pro Logic
Dolby Pro Logic is an improved technique used to
decode vast numbers of existing Dolby Surround
softwares. This new technology enables a discrete 5channel playback with 2 main left and right channels, 1
center channel, and 2 rear left and right channels (instead
of only 1 rear channel for conventional Pro Logic
technology). A music mode is also available for 2-channel
sources in addition to the movie mode.
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can
enjoy the depth of sound and natural spatial
representation of DTS digital surround in your home.
This system produces practically distortion-free 6-channel
sound (technically, a left, right and center channels, 2 rear
channels, plus an LFE 0.1 channel as a subwoofer, for a
total of 5.1 channels).
The unit incorporates DTS-ES compatible decoder that
enables 6.1-channel reproduction by adding the rear
center channel to existing 5.1-channel format. (The rear
center channel is created from rear left and right
channels.)
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5 channels in a Dolby Digital or
DTS 5.1 channel systems.
■ CINEMA DSP
■ SILENT CINEMA
YAMAHA has developed a natural, realistic sound effect
DSP algorithm for headphones.
Parameters for headphones have been set for each sound
field so that accurate representations of all the sound field
programs can be enjoyed using headphones.
58
0110V630_54-60_EN(GB)
58
D I G I T A L
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers and
designed for acoustic effects. Since home conditions,
such as room size, wall material, number of speakers, and
so on, can differ so widely, it’s inevitable that there are
differences in the sound heard as well. Based on a wealth
of actually measured data, YAMAHA CINEMA DSP uses
YAMAHA original sound field technology to combine
Dolby Pro Logic, Dolby Digital and DTS systems to
provide the visual and audio experience of movie theater
in the listening room of your own home.
1/11/02, 7:43 PM
GLOSSARY
YAMAHA has developed a virtual CINEMA DSP
algorithm that allows you to enjoy DSP sound field
surround effects even without any rear speakers by using
virtual rear speakers.
It is even possible to enjoy virtual CINEMA DSP using a
minimal 2-speaker system that does not include a center
speaker.
With the S-video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted
as the Y signal for the luminance and the C signal for the
chrominance through the S-video cable. Using the S
VIDEO jack eliminates video signal transmission loss and
allows recording and playback of even more beautiful
images.
■ PCM (Linear PCM)
■ Component video signal
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “pulse code
modulation”, the analog signal is encoded as pulses and
then modulated for recording.
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the
PB/CB and PR/CR signals for the chrominance. Color can
be reproduced more faithfully with this system because
each of these signals is independent. The component
signal is also called the “color difference signal” because
the luminance signal is subtracted from the color signal.
A monitor with component input jacks is required in
order to use the component signal for output.
■ Sampling frequency and number
of quantized bits
PREPARATION
■ S-video signal
INTRODUCTION
■ Virtual CINEMA DSP
BASIC
OPERAIONT
ADVANCED
OPERATION
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits.
The range of rates that can be played back is determined
based on the sampling rate, while the dynamic range
representing the sound level difference is determined by
the number of quantized bits. In principle, the higher the
sampling frequency, the wider the range of frequencies
that can be played back, and the higher the number of
quantized bits, the more finely the sound level can be
reproduced.
ADDITIONAL
INFORMATION
APPENDIX
English
59
0110V630_54-60_EN(GB)
59
1/11/02, 7:43 PM
SPECIFICATIONS
AUDIO SECTION
• Minimum RMS Output Power for Main, Center, Rear, Rear Center
20 Hz to 20 kHz, 0.06% THD, 8 Ω ....................................... 75 W
1 kHz, 0.06% THD, 8 Ω ........................................................ 80 W
• DIN Standard Output Power
[Europe model]
1 kHz, 0.7% THD, 4 Ω ........................................................ 125 W
• Maximum Power (EIAJ)
[China, Korea and General models]
1 kHz, 10% THD, 8 Ω ......................................................... 110 W
RX-V630RDS
FM SECTION
• Tuning Range
[U.S.A. and Canada models] ...................... 87.5 to 107.9 MHz
[Other models] ........................................ 87.50 to 108.00 MHz
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
Mono/Stereo .................. 2.0 µV (17.3 dBf) /25 µV (39.2 dBf)
• Selectivity (400 kHz) ......................................................... 70 dB
• Dynamic Power (IHF)
8/6/4/2 Ω .......................................................... 90/120/150/190 W
• Signal to Noise Ratio (IHF)
Mono/Stereo ........................................................ 76 dB/70 dB
• Damping Factor
20 Hz to 20 kHz, 8 Ω ................................................... 80 or more
• Harmonic Distortion (1 kHz)
Mono/Stereo ........................................................... 0.2%/0.3%
• Frequency Response
CD to Main L/R ...................................... 10 Hz to 100 kHz, –3 dB
• Stereo Separation (1 kHz) ................................................. 45 dB
• Total Harmonic Distortion
20 Hz to 20 kHz, 45 W, 8 Ω, Main L/R ................................ 0.06%
• Signal to Noise Ratio (IHF-A Network)
CD (250 mV, shorted) to Main L/R, Effect Off .................. 100 dB
• Residual Noise (IHF-A Network)
Main L/R ................................................................ 150 µV or less
• Channel Separation (1 kHz/10 kHz)
CD (5.1 kΩ terminated) to Main L/R ........................ 60 dB/45 dB
• Tone Control (Main L/R)
BASS Boost/Cut ...................................................... ±10 dB/50 Hz
TREBLE Boost/Cut ............................................... ±10 dB/20 kHz
• Phones Output ............................................................. 0.34 V/560 Ω
• Frequency Response ..................... 20 Hz to 15 kHz +0.5, –2 dB
AM SECTION
• Tuning Range ................................... 530/531 to 1710/1611 kHz
• Usable Sensitivity ....................................................... 300 µV/m
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................... AC 120 V/60 Hz
[Australia model] ................................................. AC 240 V/50 Hz
[U.K., Europe and Singapore models] ................ AC 230 V/50 Hz
[Korea model] ..................................................... AC 220 V/60 Hz
[China and General models] ..... AC 110/120/220/240 V, 50/60 Hz
• Input Sensitivity
CD, etc .................................................................... 150 mV/47 kΩ
6CH INPUT ............................................................ 150 mV/47 kΩ
• Power Consumption
[U.S.A. and Canada models] .................................. 290 W/370 VA
[Other models] ..................................................................... 290 W
Standby Mode ......................................................... approx. 0.6 W
• Output Level
OUT (REC) ........................................................... 150 mV/1.2 kΩ
OUTPUT MAIN/CENTER/REAR CENTER/
REAR (SURROUND) ............................................ 2.2 V/1.2 kΩ
OUTPUT SUBWOOFER ............................................. 4 V/1.2 kΩ
• AC Outlets
[U.S.A., Canada, Europe and Singapore models]
.......................................................... 2 (Total 100 W maximum)
[China and General models] .................. 2 (Total 50 W maximum)
[U.K. and Australia models] ......................... 1 (100 W maximum)
VIDEO SECTION
• Dimension (W x H x D)
.......................... 435 x 161 x 390 mm (17” x 6-7/16” x 15-3/8”)
• Video Signal Type ...................................................... NTSC or PAL
• Composite Video Signal Level ...................................... 1 Vp-p/75 Ω
• S-Video Signal Level
Y ................................................................................. 1 Vp-p/75 Ω
C .......................................................................... 0.286 Vp-p/75 Ω
• Component Video Signal Level
Y ................................................................................. 1 Vp-p/75 Ω
PB/CB, PR/CR ............................................................. 0.7 Vp-p/75 Ω
• Weight ...................................................................... 11.5 kg (25 lbs)
• Accessories ............................................................... Remote control
Batteries
Front VIDEO AUX jack cap
RX-V630RDS 75-ohm/300-ohm antenna adapter (U.K. model)
RX-V630RDS AM loop antenna
RX-V630RDS Indoor FM antenna
*Specifications are subject to change without notice.
• Signal to Noise Ratio ............................................................... 50 dB
• Frequency Response (MONITOR OUT)
Composite, S-Video ................................. 5 Hz to 10 MHz, –3 dB
Component ................................................. DC to 30 MHz, –3 dB
60
0110V630_54-60_EN(GB)
60
1/11/02, 7:43 PM
LIST OF MANUFACTURER’S CODES
LISTE DES CODES FABRICANTS
LISTE DER HERSTELLER-CODES
LISTA ÖVER TILLVERKARKODER
LISTA DEI CODICI DEL FABBRICANTE
LISTA DE CÓDIGOS DE FABRICANTES
LIJST MET FABRIKANTENCODES
CLARIVOX
0821, 0961, 1971
CLATRONIC 1181, 1331
CONCERTO
0791
CONDOR
0761
CONTEC
0151, 1171
CONTINENTAL EDISON
0571, 0651, 0901
CRAIG
1171
CROSLEY
0021, 0491, 1021,
1081, 1401, 1981,
2201, 2251, 2271
CROWN
2541
CTC CLATRONIC
0261
CXC
1171
DAEWOO
0101, 1501, 1511,
2611
DANSAI
0101
DECCA
0271, 0581, 0601,
0971, 1101, 1691
DECCA (UK) 0271, 0581, 0601,
1101, 1681
DEGRAAF
0451, 1351
DIXI
0991, 1511
DOMEOS
0101
DORIC
1031
DUAL
0091, 0601, 1611,
1641, 2101
DUAL-TEC
0601, 1511, 1621,
2111
DUMONT
0261, 0521, 0781,
1021, 1081, 1981,
2121, 2151
DYNATRON 0101
ELBE
1551, 1971, 2031
ELECTRO TECH
1511
ELEKTRONSKA
0771
ELMAN
0261, 1621
ELTA
1511
EMERSON
0921, 1021, 1081,
1121, 1171, 1261,
1301
ERRES
0101
ETRON
1981
EUROPHON 0261, 0581, 0601,
0771, 1091, 1621,
2001
FENNER
0101, 1511
FERGUSON
0281, 0371, 0551,
0651, 0781, 0861,
0881, 1131, 1181,
1361, 1461, 1971,
1991, 2281, 2311,
2341
FIDELITY
0451, 0761, 2281
FIDELITY (UK)
0561, 0591,
1931, 2281
FILMNET
1141
FINLANDIA 0451, 2321
FINLUX
0021, 0261, 0491,
0521, 0781, 0811,
0871, 1081, 1411,
1421, 1981, 2051,
2091, 2121, 2151,
2551
TV
ADMIRAL
0411, 0451, 0911,
1021, 1081
AIKO
0891
AKAI
0061, 0101, 0231,
1191, 1351, 1591,
1641, 1791, 1891,
1981
AKURA
1331
ALBA
1241, 1331, 2361
ALBIRAL
1971
AMSTRAD
1301, 1511
ANAM
1171
ARC EN CIEL 0571
ARCAM
0571, 0761
ARISTONA
0751
ARTHUR MARTIN 0451, 1641
ASA
0411, 0451, 0521,
0781, 0871, 1021,
1081, 1421, 2051,
2091, 2151, 2551
ASTRA
1511
ATANTIC
0761
ATLANTIC
0761
ATORI
1511
AUDIOSONIC 1181, 1321, 1511
AUSIND
0491, 1411
AUTOVOX
0091, 0351, 0481,
0491, 0601, 0781,
0951, 1051, 1081,
1391, 1421
BAIRD
1101, 1351
BANG & OLUFSEN 1081
BASIC LINE 1321, 1331
BAUER
1451
BAUR
0041, 0061, 0121,
0131, 0221, 1561
BEKO
2491, 2501
BLAUPUNKT 0221, 0231, 0241,
0251, 0471, 0741,
2201, 2211, 2221,
2231, 2241, 2261,
2571, 2581
BRANDT
0571, 0651, 0731,
0901, 1821
BRIONVEGA 1021, 1051, 1081
BRITANNIA 0761
BRUNS
0821, 0991, 1021,
1081
BSR
0391, 0691, 1621,
1901, 1981
BUSH
0451, 1241, 1331,
1641, 1741, 2131,
2151
BUSH (UK)
0481, 1561, 1611
CANDLE
0791
CENTURY
1021, 1081
CGE
0491, 0811, 0981,
1401, 1531, 1611,
1621, 1981, 2201,
2251, 2271
CITIZEN
0791
FIRST LINE
FISHER
1981
0021, 0091, 0141,
0511, 0601, 0801,
0821, 0981, 1021,
1081, 1981, 2091
FORGESTONE 2281
FORMENTI
0451, 0491, 0761,
1081, 1451, 1541,
1981
FORMENTI-PHOENIX
0021, 0431, 0451,
0591, 1411
FORTRESS
1081
FRONTECH
0451, 1181, 1981
FUJITSU
1261
FUNAI
0391, 0691, 1171,
1181, 1261
FUTURETECH 1171
GBC
0021, 0141, 1321,
1511, 1621, 1981
GEC
0451, 1101, 1281,
2321
GEC (UK)
0031, 0081, 0581,
0601, 1101, 1281,
1561
GELOSO
0021, 0411, 0451,
1321, 1511, 1621,
1981
GENERAL TECHNIC 2681
GENEXXA
0451, 1331
GOLDSTAR
0591, 0601, 0761,
0791, 1371, 1491,
1511, 1561, 1621,
1641
GOODMANS 0141, 1101, 1371,
1641, 2301
GORENJE
0981, 1061
GRAETZ
0451
GRANADA
0141, 0451, 0491,
0581, 0601, 1101,
1111, 1351, 1981,
2321
GRANADA (UK)
0081, 0141,
0451, 0491, 0581,
0601, 1031, 1311,
1521, 1561, 1641
GRUNDIG
0221, 0231, 0471,
0491, 0711, 0741,
1381, 2021, 2041,
2141, 2151
HANSEATIC 0021, 0121, 0141,
0431, 0591, 1561
HANTAREX 0581
HEMMERMANN
0061
HIFIVOX
0331, 0571
HINARI
0071, 0141, 0451,
1261, 1351, 1511,
1641, 1981, 2011
HITACHI
0001, 0011, 0031,
0081, 0141, 0291,
0331, 0341, 0451,
0601, 0631, 0701,
1281, 1561, 1601,
1821, 1831, 1841,
1861, 1871, 1881,
1891, 1941, 1981,
2051, 2321, 2341
HYPER
0591, 0601, 1511,
1621
IMPERIAL
0451, 0491, 0811,
0981, 1401, 1611,
1621, 2201, 2251,
2271
INGERSOL
1511
INNO HIT
0581, 0601, 0841,
1101, 1331, 1371,
1511, 2011
INNOVATION 2591, 2601, 2611,
2621, 2641, 2651,
2661, 2711, 2721,
2761, 2771, 2781
INTERFUNK 0031, 0041, 0061,
0121, 0181, 0451,
0491, 1081, 1641,
1791, 1821, 1981,
2231
IRRADIO
0491, 1321, 1331,
1371, 1411, 1511,
2011
ISUKAI
1331
ITT
0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431
ITT-NOKIA
0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431
JVC (VICTOR) 0071, 0721, 1441,
1581, 1591, 1741,
1791
KAISUI
0591, 1321, 1331
KAMOSONIC 0601
KARCHER
0591, 0601, 0841,
1091, 1321, 1511,
1561, 2051
KAWASHO
0761
KENDO
0261
KENNEDY
0021, 0351, 0951,
1981
KONKA
2701
KORTING
0431, 1011, 1021,
1081, 1541
I
08V630RDS_code(GB)
1
1/11/02, 9:16 PM
NECKERMANN
KTV
LENOIR
LEYEO
LIFETEC
0601, 1171
0601, 1511
1181
2591, 2601, 2611,
2621, 2641, 2651,
2661, 2671, 2681,
2691, 2711, 2761,
2771, 2781
LOEWE OPTA 0121, 0131, 0581,
0611, 1081
LOGIC
1691, 2281
LOGIK
0551, 1681, 2281
LOWEWE
0831
LUMA
0351, 0451, 1901
LUXMAN
0791
LUXMAN STEREO TUNER
0791
LUXOR
0001, 0061, 0181,
0341, 0421, 0451,
0461, 0491, 0601,
0671, 1351, 1371,
1561, 1601, 1911,
1921, 1981
LYCO
1181
MAGNADYNE 0021, 0061, 0261,
0581, 0641, 0771,
1021, 1081, 1621,
1981
MAGNAFON 0261, 0491, 0581,
0591, 0641, 0761,
1091, 2001
MANESTH
0101
MARANTZ
0101
MARELLI
1081
MARK
0101
MATSUI
0061, 0451, 0601,
0691, 1101, 1151,
1241, 1271, 1301,
1511, 1561, 1681,
1691
MAXIMAL
0071, 1981
MCMICHAEL 1281
MEDION
2591, 2601, 2611,
2621, 2641, 2651,
2661, 2671, 2681,
2691, 2711, 2721,
2761, 2771, 2781
MEMOREX
1511
METZ
0231, 0741, 1001,
1041, 1081, 1481,
2071, 2081
MGA
1231
MICROMAXX 2591, 2621, 2641,
2651, 2711, 2761,
2771, 2781
MINERVA
0221, 0231, 0491,
1381, 2141, 2151
MISTRAL
2281
MITSUBISHI 0141, 0201, 0231,
0661, 1191, 1201,
1231, 1671, 1691,
1741
MIVAR
0491, 0501, 0581,
0591, 0761, 0771,
1371, 1431, 2031
MTC
0791
MULTITECH 0261, 0581, 0601,
0641, 0981, 1321,
1511
MURPHY
0451, 2091
MURPHY (UK) 0081, 1031
N.E.I.
0101, 0961
NAD
1341
NEC
0141, 1711, 1721,
1731
NEDIATOR
NICAMAGIC
NIKKAI
0451, 0601,
0981, 1081,
1561, 1931,
1981, 2211,
2231, 2241
0101
0761
1101, 1331, 1641,
1701, 2011
NOBLIKO
0261, 0491, 0591,
0641, 1381, 1411
NOGAMATIC 0571
NOKIA
0031, 0041, 0051,
0061, 0071, 0081,
0181, 0411, 0451,
0491, 1241, 1291,
1351, 1501, 1601,
1641, 1741, 1921,
1981, 2091, 2331,
2431, 2461, 2791
NORDMENDE 0031, 0291, 0331,
0451, 0531, 0541,
0571, 1051, 1131,
1591, 1791, 1811,
1821, 1891, 1941,
2631
OCEANIC
0321, 1651, 1981
OCEANIC (F) 0031, 0061, 0321,
0441, 1661
ONCEAS
0601
ONWA
1171
ORION
0061, 0391, 0691,
0851, 1211, 1241,
1251, 1301, 1481,
1511, 1681, 1691,
1981, 2371, 2421
OSAKA
2011
OSAKI
1101, 1331, 2011
OSUME
0151
OTTO VERSAND
0021, 0121,
0141, 0221, 0601,
1561, 1741, 1981
PAEL
0591, 1411
PANASONIC 0031, 0201, 0211,
0451, 0701, 1311,
1751, 1961, 2561,
2741
PANORAMIC 2351
PATHE MARCONI 0571
PATHE’ CINEMA (F) 0431, 0591,
1621, 1661, 1971
PAUSA
1511
PAUZA
1511
PERDIO
0891, 1101
PHILCO
0021, 0491, 0811,
0981, 1021, 1081,
1401, 1611, 1621,
1751, 2201, 2251,
2271, 2451, 2471
PHILIPS
0101, 0361, 0591,
0621, 0681, 0751,
0761, 1021, 1081,
1281, 2031, 2281,
2291, 2431, 2441,
2511, 2731
PHOENIX
1081
PHONOLA
0751, 1081
PIONEER
0291, 0451, 1341,
1821
PRANDONI-PRINCE 0411, 0451,
0491, 0581, 1411
PRANDONI-PROMCE 0451,
0491, 0581
PRIMA
PROFEX
PROTECH
QUELLE
0451
1981
0641, 1181, 1981
0041, 0061, 0121,
0221, 0231, 0391,
0491, 0521, 0601,
0781, 1371, 1381,
1411, 1421, 1641,
1681, 2051, 2091,
2141, 2151, 2201,
2211, 2231, 2241,
2251, 2271, 2551,
2571, 2581
REDIOMARELLI
0101, 0451,
0661, 0771, 1081
RADIONETTE 0031, 2051, 2091
RADIOLA
2291
RANK
0481, 2151
RBM
2131, 2151
RBM (UK)
0481
REDIFFUSION 0451, 0661, 1641,
1981, 2331
REDIFFUSION (UK) 0061, 0081,
1031
REX
0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
RFT
0991, 2511
ROADSTAR
1321, 1511
ROTEL
0151
SABA
0291, 0331, 0421,
0451, 0531, 0541,
0571, 0581, 0651,
0731, 0931, 1021,
1071, 1081, 1131,
1791, 1811, 1821,
1891, 1941, 2631
SACCS
1971
SAISHO
0451, 0601, 1161,
1241, 1301, 1511,
1671, 1681, 1691
SALORA
0011, 0041, 0061,
0071, 0341, 0451,
0671, 1291, 1351,
1521, 1561, 1601,
1641, 1911, 1921,
1931, 1981, 2321
SAMBERS
0261, 0491, 0581,
0641, 1091, 1371,
1411, 2001
SAMSUNG
0101, 0601, 0841,
0981, 1101, 1181,
1371, 1511, 2011
SANYO
0141, 0151, 0401,
0601, 0801, 0821,
0981, 1021, 1101,
1111, 1291, 1351,
1691, 1741, 2051,
2091, 2551
SBR
0681, 0751, 1281,
2281
SCHAUB LORENZ 0451
SCHNEIDER 0021, 0071, 0091,
0451, 0511, 0591,
0601, 0751, 1321,
1361, 1621, 1641,
2101, 2111, 2291
SCOTT
1171, 1261
SEG
0261, 0601, 0821,
0991
SEI
0641, 0691, 1081,
1301, 1481, 1981
II
08V630RDS_code(GB)
2
1/11/02, 9:16 PM
SELECO
0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
SENTRA
1601
SHARP
0141, 0151, 0191,
1761, 1781
SIAREM
0021, 0261, 0581,
0641, 1021, 1081,
1981
SICATEL
1971
SIEMENS
0151, 0221, 0231,
0451, 0741, 2011,
2201, 2211, 2221,
2231, 2241, 2261,
2571, 2581
SILVER
1181
SINGER
0021, 0261, 1021,
1081
SINUDYNE
0021, 0061, 0101,
0261, 0391, 0641,
0691, 0851, 0941,
1021, 1081, 1241,
1301, 1321, 1481,
1631, 1981
SKANTIC
0451
SOLAVOX
0451, 1641, 2011
SONOKO
0101, 1181, 1511
SONY
0141, 0171, 1121,
1681, 1691, 2751
SOUNDESIGN 1171
SSS
1171
STERN
0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
SUNKAI
0691
SUPRA
0791
TANDBERG
0161, 0331, 0611,
1021, 1421, 1771,
1791, 2081
TANDY
0191, 0451, 1331,
1531
TASHIKO
0141
TATUNG
0271, 0581, 0601,
0971, 1101, 1681,
1691
TCM
2621, 2641, 2711,
2761, 2771, 2781
TECHNICS
1311
TECHWOOD 0791
TEKNIKA
1171, 1231, 1261
TELE
1141
TELEAVIA
0571, 0651, 0731,
1821
TELEFUNKEN 0291, 0301, 0311,
0551, 0731, 1131,
1471, 1591, 1791,
1801, 1811, 1821,
1991, 2161, 2171,
2181, 2191, 2201,
2251, 2271, 2521,
2631
TELETECH
1511
TEMPEST
2381, 2391, 2401,
2411
TENSAI
1331, 2091
TEXET
0601
THOMSON
0331, 0481, 0531,
0571, 0631, 0651,
0731, 0901, 1241,
1571, 1591, 1791,
1811, 1821, 1891,
1941, 2531
THORN
0741, 0861, 2091,
2251, 2271, 2281
THORN-FERGUSON 0281, 0371,
0551, 0651, 0781,
0861, 0881, 1131,
1181, 1361, 1461,
1971, 1991, 2281
TMK
0141, 0791, 1471
TOSHIBA
0141, 0381, 0481,
1221, 1271, 1701,
1741, 1851, 2151,
2801, 2811
TRANS CONTINENS 0451
TRISTAR
2281
TRIUMPH
0481, 0581, 2121
UHER
0431, 0451, 0481,
0491, 0511, 1311,
1541
ULTRAVOX
0021, 0261, 0591,
1021, 1081, 1981
UNIVERSUM 1181, 2051
UNIVOX
1971
VEGAVOX
0811
VEXA
0101, 1511
VIDEOTON
2481
VORTEC
0101, 0651
VOXSON
0411, 0451, 0491,
1021, 1081
WALTHAM
0451
WATSON
0431, 2201, 2241
WATT RADIO 0021, 0061, 0261,
0591, 0641, 0761,
1091, 1971, 1981,
2001
WEGA
0141, 1081, 1981
WEGA COLOR 1021
WELTBLICK 0101
WESTON
1621
WHITE WESTINGHOUSE
0101, 0261, 0431,
0591, 0761, 1401,
1541
YOKO
0601, 1511
ZANUSSI
0071, 0101, 0351,
0411, 0451, 0951,
1901, 2061, 2101,
2111
ZOPPAS
0451
SATELLITE TUNER
AKAI
ALBA
AMSTRAD
1276
0826, 1276
0166, 0796, 1016,
1026, 1296
ANKARO
0476
AST
0406
ASTRA
0126
BARCOM
0476
BLAUPUNKT 0966
BMC SATELLITE
0106
BRITISH TELECOM 1276
BUSH
0826
BUSH (UK)
0956
CAMBRIDGE 0196, 1276
CANAL PLUS (FRANCE)
1536
CHAPARRAL 0016, 0696, 1006
COLUMBUS 0616
CONNEXIONS 0306, 0426
DISCUS ELIPSE
0856, 0866
DISKXPRESS 0426, 0476
DRAKE
1516
ECHOSTAR
0226, 0236, 0606,
0626, 0666, 0926,
0996, 1046, 1056,
1066, 1106
ELTA
1286
ELTA SAT
0146
EURODEC
1226, 1236, 1246
FERGUSON
0046, 0176, 0186,
0296, 0846, 0956,
1306
FINLUX
0976
FRACARRO 0026, 0536, 0776
FUBA
0476, 0616, 0636,
1056
GIUCAR RECORD 0206, 0336
GRUNDIG
0176, 0946, 0956,
0966
HIGH PERFORMANCE
0916
HIRSCHMANN
0756, 0966
HITACHI
0446, 0516, 0706,
0946
ICX INTERNATIONAL 0886
ITT
0066, 0126, 0176,
0446, 1156
ITT/NOKIA
0066, 0126, 0176,
0446, 1156
JEEMON
0146
JERROLD
0846, 0986
JOHANSSON 0246
JVC
1276
KATHREIN
0116, 0266, 0276,
0366
KOSMOS
0266
KYOSTAR
1036, 1086
LENG
0246
LIFESAT
1326, 1346, 1356
LUXOR
0126, 0136, 0446,
0466, 0506, 1156
MACAB
0356
MASPRO
0016, 0116, 0256,
0956
MEDION
1326, 1346
METZ
0966
MICROMAXX 1326, 1346
MITSUBISHI 0966
MORGANS
0596
MURATTO
0406
NEC
0286, 0316, 0766,
0786, 0836
NETWORK
0046
NIKKO
1136, 1146
CABLE TV
CABLETIME 1446, 1456, 1476
CLYDE CABLEVISION
1426
FILMNET
1396, 1436
FRANCE TELECOM 1386
GEC
1426
JERROLD
1416
MOVIE TIME 1466
NSC
1466
PHILIPS
1386
PIONEER
0006
SAMSUNG
1496
SCIENTIFIC ATLANTA
1486, 1506
STARCOM
1416
STS
1466
TANDBERG
1366
TELE
1436
TELE +1
1436
TELESERVICE 1406, 1476
TUDI
1376
UNITED CABLE
1416
ZENITH
1406
NOKIA
0066, 0126, 0176,
0446, 1156, 1166,
1336
NORSAT
0786
OTTO VERSAND
0966
PACE
0046, 0176, 0296,
0936, 0956, 1306,
1566, 1576
PACE MSS
0946
PACE SKY DIGITAL BOX (UK)
1526
PALCOM
0616, 0686, 0706
PALSAT
0396
PALTEC
0706
PANASONIC 0806, 1306
PANSAT
1076
PHILIPS
0326, 0346, 0476,
0956, 1126, 1186,
1196, 1206, 1216,
1306, 1316
PROSAT
1176
PTT TELECOM 0306, 0896
QUELLE
0966
RADIX
1056
REDIFFUSION 0316, 0786
RFT
1186, 1196, 1206,
1216
SAGEM
1256, 1546
SAKURA
0566, 0816
SALORA
0066, 0126, 0136,
0446, 0456, 0486,
0496, 0576
SAMSUNG
0746, 0756
SAT
0406
SATCOM
0896
SATECO
0646
SECTOR
1266
SEDEA
1096
SENTRA
0416
SIEMENS
0896, 0966
SINTRACK
0906
SKYLAB
0476
SKYSCAN
0876
SONY
0736, 0946
STELLA
0306
STRONG
0156, 0396, 1036,
1086
STV
0636
TANDBERG
1116
TANDY
0916
TANTEC
0616
TATUNG
0516, 0546
TECHNISAT 0086, 0096, 0526,
0556, 1056
TELECOM
0306
TELEMAX
0586
THORN-FERGUSON 0046, 0076,
0176, 0186, 0956
TOSHIBA
0946
TPS (FRANCE) 1546
TRIAD
0406
UNIDEN
0036, 0216, 0676,
0716, 0726
US ELECTRONICS 0886
VORTEC
0756, 1036, 1076
VTECH
0436
WINERSAT
0246
WISI
0056, 0356, 0376,
0386, 0406, 0656,
1056, 1156
WOLSEY
0916
XCOM MULTIMEDIA 1556
XSAT (FRANCE)
1556
ZEHNDER
0266, 0406
ZENDER
0406
VCR
AIWA
AKAI
0042, 0352, 0432
0042, 0422, 0492,
0582, 0612, 0642,
0652, 0762, 0912
ALBA
0002, 0112, 0282,
0332, 0342, 0972
AMSTRAD
0322, 0432, 0452
ANITECH
0002
ANITSCH
1002
ASA
0012, 0052
AUDIOSONIC 0002
BAIRD
0042, 0282, 0492
BANG & OLUFSEN 0042
BAUR
0052, 0062, 0812
BLAUPUNKT 0062, 0092, 0252,
0462, 0672, 0992
BRIONVEGA 0032
BUSH
0002, 0282, 0332,
0342, 0512, 0972
BUSH (UK)
0812
CAPEHART
0112
CGE
0042, 0432, 0762
CRAIG
0072, 0482
CROWN
0112, 0282, 0622
DAEWOO
0112, 0282, 0622
DANSAI
0012
DAYTRON
0112
DECCA
0042, 0052, 0432,
0942
DECCA (UK) 0052
DEGRAAF
0052, 0132, 0432,
0532, 0602
DIXI
0442
DUAL
0042, 0632
DUMONT
0052, 0432, 0532
DYNATECH 0432
DYNATRON 0012
ELBE
0122
ELIN
0072
EMERSON
0012, 0162, 0202,
0432, 0512, 0522
ERRES
0012
FERGUSON
0042, 0712, 0722,
0852, 0902, 1012,
1022, 1082
FIDELITY
0432
FINLANDIA 0052, 0532
FINLUX
0012, 0042, 0052,
0082, 0262, 0382,
0432, 0462, 0492,
0532, 0572, 0602,
0912
FIRST LINE
0002, 0912
FISHER
0162, 0482, 0532,
0542, 0572, 0592
FORMENTI-PHOENIX
0012, 0052
FRONTECH
0112
FUNAI
0432
GBC
0002
GEC (UK)
0022, 0052
GELOSO
0002
GENERAL TECHNIC 1172
GOLDSTAR
0012, 0122, 0812,
0952
GOODMANS 0002, 0072, 0282,
0432, 0502
GOODMANS (UK) 0002
GRAETZ
0022, 0042
GRANADA
0052, 0132, 0532,
0572
III
08V630RDS_code(GB)
3
1/11/02, 9:16 PM
NOKIA
0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762,
1152
NORDMENDE 0042, 0102, 0142,
0192, 0222, 0242,
0392, 0402, 0632,
0732, 0742, 0762,
0782, 0792, 0832,
0842, 0872
OLYMPUS
0462
OPTONICA
0132, 0502
ORION
0162, 0202, 0312,
0442, 0512, 0522,
0982
OSAKA
0432
OSAKI
0002, 0012, 0432
OTTO VERSAND
0052, 0062,
0812
PANASONIC 0022, 0212, 0462,
0672, 0992, 1092,
1102, 1182
PENTAX
0172, 0602
PERDIO
0432
PHILCO
1062
PHILIPS
0052, 0082, 0092,
0152, 0182, 0362,
0372, 0382, 0472,
0502, 1072
PHONOLA
0052, 0152
PILOT
0012
PIONEER
0052, 0142, 0372,
0472
PORTLAND
0112
PROLINE
0432
PYE
0052, 0152
QUARTZ
0572
QUELLE
0012, 0032, 0042,
0052, 0062, 0072,
0092, 0202, 0462,
0522, 0942
RADIONETTE 0022
REALISTIC
0012, 0072, 0132,
0432, 0482, 0502,
0532, 0572
RET
1072
REX
0042, 0742, 0782
RICOH
0952
SABA
0042, 0142, 0192,
0222, 0242, 0392,
0632, 0732, 0742,
0762, 0772, 0782,
0792, 0872
SAISHO
0162, 0202, 0292,
0442, 0512, 0522,
0972
SALORA
0192, 0572, 0812,
0822, 0912
SAMSUNG
0052, 0072, 0622,
0652, 1192
SANSUI
0042, 0142
SANYO
0482, 0532, 0562,
0572
SBR
0052, 0152, 0182
SCHAUB LORENZ 0022, 0042
SCHNEIDER 0002, 0012, 0052,
0072, 0432
SEG
0002, 0072
SEI-SINUDYNE
0442
SELECO
0042
SENTRA
0112
SHARP
0132, 0502, 0702
SHINTOM
0002
SIEMENS
0062, 0092, 0252,
0572
GRANADA (UK)
0052, 0092,
0462, 0602, 0812,
0822
GRUNDIG
0052, 0062, 0092,
0232, 0252, 0262,
0752, 0802
HANSEATIC 0052, 0812
HARMAN/KARDON 0122, 0922
HCM
0002
HINARI
0002, 0202, 0412,
0442, 0522
HITACHI
0042, 0172, 0292,
0432, 0602, 0662,
0812, 1022
IMPERIAL
0072, 0432
INGERSOL
0442
INNO HIT
0002, 0052, 0072
INNOVATION 1142, 1162, 1172
INTERFUNK 0022, 0052
IRRADIO
0002, 0012
ITT
0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762
ITT-NOKIA
0022, 0032, 0042,
0072, 0292, 0492,
0532, 0572, 0762
JENSEN
0042
JVC (VICTOR) 0042, 0102, 0142,
0272, 0742, 0762,
0782, 0902
KARCHER
0052, 0072, 0812
KENDO
0492
KENWOOD
0042, 0142, 0572
LIFETEC
1142, 1162, 1172
LLOYD
0432
LOEWE OPTA 0052, 0092, 0152
LOGIK
0002, 0072, 0442
LUMA
0162
LUXOR
0492, 0572, 0812
M ELECTRONIC 0432
MAGNADYNE 0052
MAGNASONIC 0572
MANESTH
0012
MARANTZ
0012, 0052, 0092,
0122, 0502
MARK
0012
MARTA
0012
MATSUI
0012, 0442, 0512,
0522, 0812, 0972
MEDION
1142, 1162, 1172
MEMOREX
0012, 0132, 0432,
0482, 0532, 0572
METZ
0062, 0092, 0932
MGA
0912
MICROMAXX 1142, 1162, 1172
MINERVA
0062, 0092, 0252
MINOLTA
0172, 0602
MITSUBISHI 0052, 0062, 0142,
0912, 0922
MTC
0072, 0432
MULTITECH 0002, 0052, 0062,
0282, 0432
MURPHY
0432
N.E.I.
0012, 0052
NATIONAL
0462
NEC
0042, 0122, 0142
NECKERMANN
0032, 0042,
0052, 0072,
0092, 0202,
0522, 0572,
0762, 0812
NIKKAI
0112
NOBLIKO
0092
SINUDYNE
0052, 0382, 0442,
0932
SONOKO
0282
SONY
0432, 0552, 0682,
0692, 0942, 0952,
0962, 1122, 1132
STS
0602
SUNKAI
0512
SUNSTAR
0432
SYLVANIA
0432, 0912
SYMPHONIC 0432, 0912
TANDBERG
0062, 0162, 0522,
0932
TASHIKO
0132, 0432
TATUNG
0042, 0052, 0432,
0922
TCM
1142, 1162, 1172
TEAC
0042, 0432
TECHNICS
0462
TEKNIKA
0012, 0432
TELEFUNKEN 0042, 0192, 0632,
0732, 0742, 0762,
0782, 0882, 0892
TEMPEST
1032, 1042, 1052
TENOSAL
0002
THOMSON
0042, 0102, 0142,
0192, 0402, 0632,
0762
THORN
0042, 0902
THORN-FERGUSON 0042, 0222,
0302, 0712,
0722, 0742,
0762, 0852,
0862, 0872,
0902
TMK
0522
TONSAI
0002
TOSHIBA
0042, 0622, 0912
TOTEVISION 0012, 0072
TRIUMPH
0922
UHER
0042, 0072
ULTRAVOX
0032
UNITECH
0072
VECTOR RESEARCH
0122
VIDEON
1162, 1172
WELTBLICK 0012
WHITE WESTINGHOUSE
0032
XENON
0162
YAMAHA
0042, 1202
YOKO
0012, 0062, 0072
DVD PLAYER
AKAI
DENON
HITACHI
JVC
KENWOOD
MAGNAVOX
MITSUBISHI
ONKYO
PANASONIC
PHILIPS
PIONEER
PROSCAN
RCA
SAMSUNG
SHARP
SONY
TECHNICS
THOMSON
TOSHIBA
YAMAHA
ZENITH
0058
0188
0198
0088, 0178
0148
0128
0138
0068, 0128
0028
0098, 0128
0108, 0118
0158
0158
0078
0038
0018
0028
0168
0048, 0128
0008, 0028, 0098
0128
IV
08V630RDS_code(GB)
4
1/11/02, 9:16 PM
LD PLAYER
AIWA
FUNAI
HITACHI
MAGNAVOX
PANASONIC
PIONEER
RCA
REALISTIC
SAMSUNG
SONY
VICTOR
YAMAHA
0137
0137
0047
0077
0027
0037
0067
0137
0017, 0087
0057, 0097, 0107,
0117
0127
0007
CD PLAYER
ACCUPHASE
ADC
ADCOM
AKAI
0315
0865
0785, 1015
0115, 0125, 0725,
0735, 0745, 0935,
1155
ARCAM
1875
ARCAM-ROTEL
0165
AUDIO-TECHNICA 0835
AUDIOSONIC 0155
AIWA
1105, 1235, 1245,
1765, 1915, 1935
BSR
0875
CALIFORNIA AUDIO LAB
1075
CARRERA
0555, 0875
CARVER
0825, 1415
CYRUS-ROTEL
0205
DENON
0045, 0955, 1045,
1595, 1795, 1805
DUAL
1005
ELIN
0185
EMERSON
1015, 1285, 1675
FISHER
0105, 0595, 0605,
0825, 1165, 1175
GENEXXA
0525, 0825, 0855,
0875, 0995, 1265,
1285, 1345, 1355,
1485, 1575, 1675,
1715, 1825
GOLDSTAR
0555, 1185, 1195,
1585
GRUNDIG
0175
HARMAN KARDON 0325, 0495,
0565, 1135, 1145,
1155
HITACHI
0065, 0585, 0685,
0945, 1005, 1015,
1225, 1545
INNOVATION 1995, 2005, 2015
ITT-NOKIA
0185
JVC (VICTOR) 0385, 0395, 0455,
0575, 0585
KARCHER
0485
KENWOOD
0025, 0055, 0145,
0215, 0595, 0675,
0695, 0705, 0715,
0925, 1355, 1485,
1575, 1675, 1715,
1825
KORTING
0175
LIFETEC
2015
LIGHT CONTROL 1155, 1645,
1655, 1665
LINN
0165, 1875
LUXMAN
0265, 0275, 0795,
0805, 1295, 1305,
1555, 1925
THOMSON
1005
TOSHIBA
0755, 0765
VECTOR RESEARCH
0555, 0865
YAMAHA
0005, 0015, 0085,
0345, 0615, 0655,
0815, 0835, 0895,
1815
LUXOR
MAGNAVOX
MARANTZ
0185, 1895, 1905
1865, 1875
0165, 0175, 0545,
0665, 1275, 1335,
1405, 1505, 1875,
1955
MATSUSHITA 1095, 1605
MCS
0535
MEDION
0075, 1995, 2005,
2015
MEMOREX
0525, 1015, 1265,
1275, 1285, 1675
MGA
1125
MICROMAXX 2015
MISSION
0165, 1875
MITSUBISHI 1125, 1205
NAD
0135, 0255, 0285,
0295, 0305, 0345,
0755, 0765, 1315,
1325
NAKAMICHI 0635, 0645, 1565
NEC
0405, 0535, 0775,
0785
NECKERMAN 0155, 0225
NIKKO
0835, 1165
OCEANIC
0185
OKANO
0155, 0225
ONKYO
0885, 1385, 1425,
1455, 1515
PANASONIC 1055, 1075, 1615,
1625
PHILIPS
0165, 0175, 0195,
1865, 1875
PIONEER
0095, 0335, 0425,
0435, 0445, 0525,
0855, 1035, 1945
PROTON
0905, 1875
QUASAR
1075
RADIOLA
1845, 1855
RADIOTONE 0485
REALISTIC
0825, 1015, 1265,
1275, 1285, 1575
ROTEL
1875
SABA
1005
SAE
1875
SALORA
0185
SANSUI
0415, 0965, 0975,
0985, 1255, 1675,
1875
SANYO
0625, 0825, 0845,
0915
SCHNEIDER 1845, 1855
SCOTT
1285, 1675
SHARP
0025, 0035, 1025,
1115, 1275, 1635,
1785, 1815, 1825,
1835
SHERWOOD 1275, 1445
SIEMENS
1085
SIGNATURE 1155
SONY
0345, 0355, 0365,
0375, 0865, 1685,
1695, 1705, 1715,
1725, 1735, 1745
SYLVANIA
1875
TANDBERG
1885
TASHIKO
1525
TCM
1985, 2015
TEAC
0235, 0245, 1275,
1365, 1375, 1395,
1435, 1465, 1475
TECHNICS
0465, 0475, 1065,
1075, 1625
TELEFUNKEN 1005
THETA DIGITAL
1865
CD RECORDER/CD-RW
HITACHI
JVC
MARANTZ
PHILIPS
PIONEER
YAMAHA
0304
0334
0314, 0324
0274
0284, 0294
0244
MD RECORDER
KENWOOD
SHARP
PIONEER
SONY
YAMAHA
0214
0264
0254
0224
0024, 0224, 0234
TAPE DECK
AKAI
DENON
GRUNDIG
HARMAN
JVC
KENWOOD
KORTING
LUXMAN
MARANTZ
NAD
ONKYO
PHILIPS
PIONEER
SONY
YAMAHA
0124
0204
0134
0044
0194
0164
0134
0054, 0064, 0074,
0084
0134, 0144
0174
0184
0134, 0144, 0154
0034, 0114
0094, 0104
0004, 0014
V
08V630RDS_code(GB)
5
1/11/02, 9:16 PM
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia
V874860