Dishwasher
Instruction Manual
CONTENTS
Technical specifications ……………………………………………………..
Conformity with the standards and Test data ……………………………..
4
4
Safety information and Recommendations…………………………………..
•
Recycling .......……………………….........................................................
•
Safety information ……………………………………………………………
•
Recommendations …...………………………………………………………
•
Items not suitable for dishwashing …………………………………………
5
5
5
8
9
Installing the machine …………………………………………………………..
•
Positioning the machine ……………………………………………………..
•
Water connections …………………...............................................................
•
Water inlet hose ….…………………………………………………………..
•
Water outlet hose …..………………..............................................................
•
Electrical connection…………………………………………………………
•
Fitting the machine undercounter ………………………………………….
•
Prior to using the machine ………………………………………………….
9
9
10
11
12
13
14
16
Preparing the machine for use …………………………………………………
•
The importance of water decalcification …………………………………..
•
Filling with salt ………………………………………………………………..
•
Testing strip……………………………………………………………………
•
Adjusting salt consumption………………………………………………….
•
Detergent usage ……………………........................................................
•
Filling the detergent compartment………………………………………….
•
Combined detergent….………………………………………………………
•
Filling with rinse aid and making the setting……………………………….
16
16
16
17
17
19
19
19
20
•
•
1
Loading your dishwasher .…………………………………………………….
•
Alternative basket loads …………………………………………………...
21
23
Programme descriptions .……………………………………………………..
•
Programme items …………………………………………………………..
25
25
Getting familiar with your machine …………………………………………… 26
Switching on the machine and selecting a programme……………........
•
Switching on the machine………………………………………………….
•
Programme follow-up ………………………………………………………
•
Changing a programme ……………………………………………………
•
Changing a programme with resetting …………………………………...
•
Switching the machine off ….……………………………………………...
28
28
28
28
29
29
Maintenance and Cleaning ........................................................................
•
Filters ..………………………………………………………………………
•
Spray arms ………………………………………………………………….
•
Hose filter ……………………………………………………………………
30
30
31
31
Failure codes and what to do in case of failure …………………………
32
Practical and useful information…….........................................................
34
2
1
2
13
3
12
Active Drying Unit: This system provides
better drying performance for your dishes.
11
3
4
5
10
6
9
7
8
1.
2.
3.
4.
5.
6.
Worktop
Upper basket with racks
Upper spray arm
Lower basket
Lower spray arm
Filters
7.
8.
9.
10.
11.
12.
Rating plate
Control Panel
Detergent and rinse-aid dispenser
Cutlery basket
Salt dispenser
Upper basket track latch
Technical specifications
Capacity
Height
Height (without worktop)
Width
Depth
Net Weight
Electricity input
Total Power
Heating Power
Pump Power
Drain Pump Power
Water supply pressure
Current
12 place settings
850 mm
820 mm
598 mm
598 mm
46 kg
220-240 V, 50 Hz
1900 W
1800 W
100 W
30 W
0.03 MPa (0,3 bar)-1 MPa (10 bar)
10 A
Conformity with the standards and Test data / EU
Declaration of Conformity
This product meets the requirements of all applicable EU
directives with the corresponding harmonised standards,
which provide for CE marking.
Important Note for User:For softcopy of this user manual,
please contact following address:
"dishwasher@standardtest.info”.In your e-mail, please
provide the model name and serial number (20 digits) which
you can find on the appliance door.
4
SAFETY INFORMATION AND RECOMMENDATIONS
Recycling
• Certain components and the packaging of your machine
have been produced from recyclable materials.
• Plastic parts are marked with international abbreviations:
(>PE< , >PS< , >POM<, >PP<, )
• Cardboard parts have been produced from recycled paper
and they should be disposed of into waste paper collection
containers for recycling.
• Such materials are not suitable for being disposed of into
garbage bins. They should be delivered to recycling centres
instead.
• Contact relevant centres in order to obtain information on
methods and points of disposal.
Safety Information
When you take delivery of your machine
• Check for any damage to your machine or to its packaging.
Never start a machine damaged in any way, make sure to
contact an authorised service.
• Unwrap the packaging materials as indicated and dispose
of them in accordance with the rules.
The points to pay attention during machine installation
• Choose a suitable, safe and level place to install your
machine.
• Carry out the installation and connection of your machine by
following the instructions.
• This machine should be installed and repaired by an
authorised service only.
• Only original spare parts should be used with the machine.
• Before installing, be sure that the machine is unplugged.
5
• Check whether the indoor electrical fuse system is connected
according to the regulations.
• All electrical connections must match the values indicated
on the rating plate.
• Pay special attention and be sure that the machine does not
stand on the electricity supply cable.
• Never use an extension cord or a multiple socket for making
a connection. The plug should be comfortably accessible
after the machine has been installed.
• After installing the machine to a suitable place, run it unloaded
for the first time.
In daily use
• This machine is for household use; do not use it for any
other purpose. Commercial usage of the dishwasher will void
the guarantee.
• Do not get up, sit or place a load on the open door of the
dishwasher, it may fall over.
• Never put into the detergent and rinse aid dispensers of
your machine anything other than those detergents and rinse
aids which are produced specifically for dishwashers. Our
company will not be responsible for any damage that might
occur in your machine otherwise.
• The water in the machine's washing section is no drinking
water do not drink it.
• Due to danger of explosion, do not put into the machine’s
washing section any chemical dissolving agents such as
solvents.
• Check whether plastic items are heat-resistant before
washing them in the machine.
•This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
6
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.Cleaning
and user maintenance shall not be made by children without
supervision.
• Do not put into your machine those items which are not
suitable for dishwashing. Also, do not fill any basket above its
capacity.Our company will not be responsible for any scratch
or rust to form on the inner frame of your machine due to
basket movements otherwise.
• Especially because hot water may flow out, the machine
door should not be opened under any circumstances while
the machine is in operation. In any case, a safety devices
ensures that the machine stops if the door is opened.
• Do not leave your dishwasher’s door open. Failure to do so
may lead to accidents.
• Place knives and other sharp-ended objects in the cutlery
basket in blade-down position.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
•This appliance is not intended for use by persons (including children) with reduced physical,sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• If EnergySave option is selected as "Yes", The door will be
opened at the end of the program. Do not force to close the
door to avoid harm auto door mechanism during 1 minutes.
The door must be open during 30 minutes to get effective
drying.( in models with auto door opening system )
Warning: Do not stand in front of the door after the signal
sounds belonging auto-open.
7
For your children’s safety
• After removing the machine’s packaging, make sure that the
packaging material is out of reach of children.
• Do not allow children to play with or start the machine.
• Keep your children away from detergents and rinse aids.
• Keep children away from the machine while it is open
because there may still be residues of cleaning substances
inside the machine.
• Be sure that your old machine does not pose any threat to
your children. Children are known to have gotten themselves
locked in old machines. To forestall such a situation, break
your machine's door lock and tear off the electrical cables.
In case of malfunctioning
• Any malfunction in the machine should be repaired definitely
by qualified persons. Any repair work performed by anyone
other than the authorised service personnel will cause your
machine to be left outside the scope of warranty.
• Prior to any repair work on the machine, be sure that the
machine is cut off from the mains.Switch off the fuse or unplug
the machine.Do not pull by the cable when unplugging. Make
sure to turn off the water tap.
Recommendations
• For energy and water saving, remove coarse residues on
your dishes before placing the dishes into the machine. Start
your machine after having fully loaded it.
• Use the pre-wash programme only whenever necessary.
• Place such hollow items as bowls, glasses and pots into the
machine in such a way that they will face down.
• You are recommended not to load into your machine any
dishes different or more than indicated.
8
Items not suitable for dishwashing:
• Cigarette ashes, candle leftovers, polish, paint, chemical
substances, iron-alloy materials;
• Forks, spoons and knives with wooden or bone, or ivory or
nacre-coated handles; glued items,items soiled with abrasive,
acidic or base chemicals.
• Plastic items that are not heat-resistant, copper or tin-coated
containers.
• Aluminium and silver objects (they may discolour, become
dull).
• Certain delicate glass types, porcelains with ornamental
printed patterns as they fade even after the first wash; certain
crystal items as they lose their transparency over time,
adhered cutlery that is not heat-resistant, lead crystal glasses,
cutting boards, items manufactured with synthetic fibre;
• Absorbent items as sponges or kitchen rags are not suitable
for dishwashing.
Warning:Take care to buy dishwasher-proof sets in your
future purchases.
INSTALLING THE MACHINE
Positioning the machine
When determining the place to put your machine on, take
care to choose a place where you can easily load and unload
your dishes.
Do not put your machine in any location where there is the
probability for the room temperature to fall below 0°C.
Before positioning, take the machine out of its packaging by
following the warnings located on the package.
9
Position the machine close to a water tap or drain. You
need to site your machine, taking into consideration that its
connections will not be altered once they are made.
Do not grip the machine by its door or panel in order to move
it.
Take care to leave a certain clearance from all sides of the
machine so that you can comfortably move it back and forth
during cleaning.
Make sure that the water inlet and outlet hoses do not get
squeezed while positioning the machine. Also, make sure
that the machine does not stand on the electrical cable.
Adjust the machine’s adjustable feet so that it can stand level
and balanced. Proper positioning of the machine ensures
problem-free opening and closing of its door.
If the door of you machine does not close properly, check if
the machine is stable on the floor it stands; if not, adjust the
adjustable feet and ensure its stable position.
Water connection
Be sure that the indoor plumbing is suitable for installing a
dishwasher. Also, we recommend that you fit a filter at the
entrance of your place or apartment so as to avoid any damage
to your machine because of any contamination (sand, clay,
rust etc.) that might be occasionally carried in through the
mains water supply or the indoor plumbing, and to forestall
such complaints as yellowing and formation of deposits after
washing.
10
Water inlet hose
Do not use the water inlet hose of your
old machine,if any. Use the new water inlet
hose supplied with your machine instead.
If you are going to connect a new or long
- unused water inlet hose to your machine
,run water through it for a while before
making the connection. Connect the water
inlet hose directly to the water inlet tap.
The pressure supplied by the tap should
be at a minimum of 0.03 Mpa and and at a
maximum of 1 Mpa.If the water pressure is
above 1 Mpa,a pressure-relief valve should
be fitted inbetween.
After the connections are made, the tap should be turned on
fully and checked for water tightness.For the safety of your
machine, make sure to always turn off the water inlet tap after
each wash programme is finished.
NOTE: Aquastop water spout is used
in some models. In case of using
Aquastop, a dangerous tension exists.
Do not cut Aquastop water spout. Do
not let it get folded or twisted.
11
Water outlet hose
The water drain hose can be connected
either directly to the water drain hole
or to the sink outlet spigot. Using a
special bent pipe (if available), the
water can be drained directly into the
sink via hooking the bent pipe over
the edge of the sink. This connection
should be at a minimum of 50 cm and
at a maximum of 110 cm from the floor
plane.
Warning: When a drain hose longer than 4 m is used, the
dishes might remain dirty. In that case, our company will not
accept responsibility.
12
Electrical connection
The earthed plug of your machine should be connected to
an earthed outlet supplied by suitable voltage and current. If
there is no earthing installation, have a competent electrician
carry out an earthing installation. In case of usage without
earthing installed, our company will not be responsible for
any loss of usage that might occur.
The indoor fuse current value should be 10-16 A.
Your machine is set according to 220-240 V. If the mains
voltage in your location is 110 V, connect a transformer of
110/220 V and 3000 W inbetween. The machine should not
be plugged in during positioning.
Always use the coated plug supplied with your machine.
Running in low voltage will cause a decline in washing quality.
The machine’s electrical cable should be replaced by an
authorised service or an authorised electrician only. Failure
to do so may lead to accidents.
For safety purposes, always make sure to disconnect the
plug when a wash programme is finished.
In order not to cause an electric shock, do not unplug when
your hands are wet.
When disconnecting your machine from the mains supply,
always pull from the plug. Never pull the cord itself.
13
Fitting the machine undercounter
If you wish to fit your machine undercounter, check whether
you have sufficient space under your countertop and whether
the wiring-plumbing is suitable to do so.1 If you decide that
the space under the countertop is suitable for fitting your
machine, remove the worktop as shown in the illustration. 2
Warning:The stand part which we will settle our machine
under it by removing its worktop has to be stable in such a
way not to allow balance disorder.
To remove the worktop, remove the screws that hold the
worktop which are located at the rear of the machine; then
push the front panel 1 cm from the front side towards the rear
and lift it.
14
Adjust the machine feet according to the slope of the floor.3
Fit your machine by pushing it undercounter without letting
the hoses get crushed or bent.4
H
Height
Without Insulation
All Product 820 mm
Product With Insulation For 2nd Basket For 3rd Basket 830mm
835 mm
Warning: After removal of worktop, the machine should be
placed in such a closed place of which dimensions are shown
at fig.
15
Prior to using the machine for the first time
•
Check whether the electricity and supply water specifications match the values indicated by the
installation instructions for the machine.
•
Remove all packaging materials inside the machine.
•
Set the water softener.
•
Add 1 kg salt into the salt compartment and fill with water up to a level at which it will almost
overflow.
•
Fill the rinse aid compartment.
PREPARING THE MACHINE FOR USE
The importance of water decalcification
For a good washing function, the dishwasher needs soft, i.e. less calcareous water. Otherwise, white
lime residues will remain on the dishes and the interior equipment. This will negatively affect your
machine’s washing, drying and shining performance. When water flows through the softener system,
the ions forming the hardness are removed from the water and the water reaches the softness
required to obtain the best washing result. Depending on the level of hardness of the inflowing water,
these ions that harden the water accumulate rapidly inside the softener system. Therefore, the
softener system has to be refreshed so that it operates with the same performance also during the
next wash. For this purpose, dishwasher salt is used.
Filling with salt
Use softener salt specifically produced for use in dishwashers. To put softener salt, first remove the
lower basket and then open the salt
compartment cap by turning it
counter clockwise.1 2 At first fill the
compartment with 1kg salt and
water3 at overflowing level If
available,using
the
funnel4
provided will make filling easier.
refit the cap and close it. If the salt
warning lamp on the control panel
becomes
on
fill
the
salt
compartment with salt again.
SALT
Fill the salt compartment with
water at first use only.
If you put a tablet into the salt
compartment, do not fill the
compartment
completely.
We
recommend that you use smallgrained or powder softener salt.
Do not put table salt into your
machine. Otherwise, the function of
the softener compartment may
decrease over time. When you start your dishwasher, the salt
compartment gets filled with water. Therefore, put the softener salt prior to starting your machine.
This way, overflowing salt gets immediately cleaned up through the wash operation. If you are not
going to wash any dishes immediately after putting salt, then run a short washing program with an
empty machine in order to avoid any damage ( to prevent corrosion )to your machine due to the salt
overflow while filling in the salt container.
16
Testing strip
The washing effectiveness of your machine depends on the softness of the tap water. For this reason,
your machine is equipped with a system that reduces the hardness in mains water supply. The
washing effectiveness will increase when the system is correctly set. To find out the water hardness
level of water in your area, contact your local water board or determine water hardness level by using
the test strip(if available).
Open the
testing
strip.
Run
water
through
your tap
for 1
min.
Keep the
testing
strip in
water for 1
sec.
Shake the
testing strip
after taking it
out of water.
Wait for
1 min.
Make your machine’s water hardness
setting according to the result obtained
through the testing strip.
Adjusting salt consumption
Table of Water Hardness Level Settings
Water
hardness
level
German
hardness
dH
French
hardness
dF
British
hardness
dE
Hardness Level Indicator
1
0-5
0-9
0-6
L1 is seen on display.
2
6-11
10-20
7-14
L2 is seen on display.
3
12-17
21-30
15-21
L3 is seen on display.
4
18-22
31-40
22-28
L4 is seen on display.
5
23-31
41-55
29-39
L5 is seen on display.
6
32-50
56-90
40-63
L6 is seen on display.
If the hardness of the water you use is above 90 dF (French hardness) or if you are using well
water; you are recommended to use filter and water refinement devices.
NOTE: Hardness level is adjusted to level 3 as a factory setting.
17
Adjust water hardness setting of your machine according to the level specified on the
test track.
3
2
1
Push the Programme selection button and hold down. 1
In the meantime, energize the machine by pushing ON/OFF button. 4
Hold down the programme selection button until “SL” on the screen goes off.
After “SL” goes off, release the programme button. 1
The machine will show the last water softening setting carried out.
You can make water hardness setting by pressing on “+” and “-”
buttons on the display. 3
3
After making water hardness setting, memorize the chosen setting by
pushing ON/OFF button. 2
18
Detergent usage
Use a detergent specifically designed for use in domestic dishwashers.
You can find powder,gel,and tablet detergents in the market that have been designed for
household dishwashers.
Detergent should be put into the compartment prior to starting the machine. Keep your
detergents in cool, dry places out of reach of your children.
Do not fill detergent into the detergent compartment more than required; otherwise it may cause
scratches on your glasses as well as lead to a poorly dissolved detergent.
Should you need more information concerning the detergent you will use, contact detergent
manufacturers directly.
Filling the detergent compartment
Push the latch to open the detergent container as shown in the
image. 1 Detergent pod has level lines inside. It is possible to
measure
the
right
detergent amount using
these lines. Detergent
pod can take totally 40
3
cm detergent.
Open the dishwasher
detergent and pour into
3
the larger compartment b 25 cm if your dishes are
3
heavily soiled or 15 cm if they are less soiled.2 If your
dishes have been kept dirty for a very long time, if there
are dried food wastes on them, and if you have overly
3
loaded the dishwasher, pour a 5 cm detergent into the pre-wash compartment and start your
machine.
You may have to add more detergent into your machine, depending on the degree of soil and
on the water hardness level in your area.
Combined detergent
Detergent manufacturers also produce combined detergents called “2 in 1”, “3 in 1” or “5 in 1”
etc.
“2 in 1” detergents contain detergent + salt or rinse aid. When using “2 in 1” detergents make
sure to check the specifications of the tablet.
Other tablet detergents contain detergent + rinse aid + salt + varlous extra functions.
Generally, combined detergents produce sufficient results under certain usage conditions only.
Such detergents contain rinse aid and/or salt in preset amounts
Points to consider when using this type of products:
•
Always make sure to check the specifications of the product you will use or whether or not
it is a combined product.
•
Check if the detergent used is appropriate for the hardness of mains water that machine is
appertaining to.
•
Observe the instructions on packagings when using such products.
•
If such detergents are in the form of tablets, never put them into the interior section or the
cutlery basket of the dishwasher. Always put the tablets into the detergent compartment in
the detergent dispenser.
19
•
•
•
They produce good results for certain types of usage only. If you are using this type of
detergents, you need to contact the manufacturers and find out about the suitable
conditions of use.
When the conditions of use of such products and the machine settings are appropriate,
they ensure savings in salt and/or rinse aid consumption.
Contact the detergent manufacturers if you are not obtaining good wash results (if your
dishes stay calcareous and wet) after having used 2 in 1 or 3 in 1 detergents. The scope of
warranty for your machine does not cover any complaints caused by the use of these types
of detergents.
Recommended usage: If you want to obtain better results while using combined detergents,
add salt and rinse aid into your machine and adjust the water hardness setting and the rinse aid
setting to the lowest position.
Solubility of the tablet detergents produced by different companies can vary
depending on the temperature and time. Therefore, it is not recommended to use such
detergents in short programs. It is more suitable to use powder detergents in such
programs.
Warning: Should any problem, which you have not encountered before, arise with the use of
this type of detergents, contact the detergent manufacturers directly.
When you give up using combined detergents
•
Fill the salt and rinse aid compartments.
•
Adjust the water hardness setting to the highest position ( 6 ) and run an empty-wash.
•
Adjust the water hardness level.
•
Make the suitable rinse aid setting.
Filling with rinse aid and making the setting
Rinse aid is used to prevent the stay of white water drops, lime
stains, white film strip-shaped stains that may form on the dishes, as
well as to increase the drying performance. Contrary to the popular
beliefs, it is used not only for obtaining shinier dishes but also for
obtaining sufficiently dried dishes. For this reason, care should be
taken that there is adequate amount of rinse aid in the rinse aid
compartment and only polishing material produced for use at
dishwashers should be used.
If the rinse aid lamp on the control panel becomes on fill the rinse aid
compartment with rinse.
To put rinse aid, remove the rinse aid compartment cap by turning it.1 Fill the rinse aid
compartment with rinse aid until the rinse aid level indicator becomes dark;2 refit the cap and
close it by turning it in a way that the nails will correspond to one another. By checking the rinse
aid level indicator on the detergent dispenser, you can understand whether or not your machine
needs rinse aid. A dark indicator b means that there is rinse aid in the compartment, while a
light indicator a shows that you need to fill the compartment with
rinse aid.
The rinse aid level adjuster can be set
to a position between 1 and 6. Factory
setting for rinse aid is the position 3.
You need to increase the degree of the
adjuster if water stains form on your
dishes after a wash, whereas you need
to decrease the degree if a blue stain
is left when wiped by hand.3
20
Warning: Use only those rinse aid materials which are allowed for use in the machine. As rinse
aid residues left as a result of overflowing will create extremely high amounts of foam and thus
reduce the washing performance, remove the excess amount of rinse aid by wiping it with a rag.
LOADING YOUR DISHWASHER
If you properly place your dishes into the machine, you will be using it in the best way in terms
of energy consumption, washing and drying performance.
There are two separate baskets for you to load your dishes into your machine. You can load into
the lower basket such round and deep items as pots with long handles, pot lids, plates, salad
plates, cutlery sets.
The upper basket has been designed for tea plates, dessert plates, salad bowls, cups and
glasses. When placing long-stem glasses and goblets, lean them against the basket edge, rack
or glass supporter wire and not against other items. Do not lean long glasses against one
another or they cannot remain steady and may receive damage.
It is more appropriate to locate the thin narrow parts into the middle sections of baskets.
You can place spoons among the other cutlery sets in order to prevent them from sticking to
one another. You are recommended to use the cutlery grid in order to obtain the best result.
To avoid any possible injuries, always place such long-handle and sharp-pointed dishes as
serving fork, bread knife etc. with their sharp points facing down or horizontally on the baskets.
Warning: Place your dishes into your machine in a way that they will not prevent the upper and
lower spray arms from spinning.
Top basket
Height Adjustable Rack
These racks are designed to increase the capacity of the
top basket. You can place your glasses and cups on the
racks. You can adjust the height of these racks. Thanks to
this feature, you can place different sizes of glasses under
these racks.
Thanks to height adjustment plastics mounted on the
basket, you can use your racks in 3 different heights. In
addition, you can place long forks, knives and spoons on
these racks laterally, so that they do not block the
revolution of propeller.
1
2
Foldable racks on the upper basket are designed in
order to let you place big items easier such as pots,
pans, etc. If requested, each part can be folded
separately, or all of them can be folded and larger
spaces can be obtained.You can use foldable racks
by raising them upwards, or by folding down.
21
Top basket height adjustment
Top basket of your machine is in upper position. When it is in this position, you can place big
items such as pans, etc. on lower basket. When you take top basket to lower position, you can
place and wash big sized plates on the top basket.
Use wheels in order to change the basket height. Open the basket retaining parts at the end of
top basket rails by turning them to the sides, and take the basket out. Change the position of the
wheels; reinstall the basket to the rail, and close basket retainer parts. In this way, you take the
top basket to lower position.
Lower Basket
Folding Racks
Folding racks consisting of four parts that are located on the lower basket of your machine are
designed in order to let you place big items easier such as pots, pans, etc. If requested, each
part can be folded separately, or all of them can be folded and larger spaces can be obtained.
You can use folding racks by raising them upwards, or by folding.
1
2
b
a
d
c
The movable cutlery basket can slide between the
front and rear wires of theBbottom basket.
22
Alternative basket loads
Lower Basket
Top basket
23
Faulty loads
Important Note for Test Laboratories
For detailed information on performance tests, please contact following address:
"dishwasher@standardtest.info” . In your email, please provide the model name and
serial number (20 digits) which you can find on the appliance door.
24
PROGRAM DESCRIPTIONS
Program items
Name of Program
Pre-washing
Washing Temperature
Type of Food Fragment
Fresh less dirty,
cofee,milk, tea
Level of Contamination
Amount of Detergent
B: 25 cm3 / 15 cm3
A: 5 cm3
small
A**
o
35 C Wash
Hot Rinse
Auto
Auto Normal
Auto
'HOLFDWH
Intense
30-50oC
50-60oC
60-70oC
Detects contamination level of dishes and sets
temperature and amount of washing water and
washing period automatically
40oC
Fresh coffee, milk,
tea, cold meat,
vegetables
50oC
Fresh coffee, milk,
tea, cold meat,
vegetables
65o C
Tarried soup, sauce,
pastry, egg, rice, potato
and meals cooked in
oven, fried food
60oC
Fresh coffee, milk,
tea, cold meat,
vegetables
small
B
small
B
Medium
A+B
Medium
A+B
Medium
A+B
high
A+B
high
A+B
Detects contamination level of dishes
and sets temperature and amount of
washing water and washing period
automatically
End
Quick 30 min.
Prewash
Eco
Super 50 min.
Prewash
65 C Wash
Prewash
o
o
25
40 C Wash
50 C Wash
Cold Rinse
60 C Wash
Cold Rinse
Hot Rinse
Hot Rinse
Cold Rinse
Hot Rinse
Dry
End
Hot Rinse
o
Dry
o
Dry
End
End
End
Program Period
(minutes)
Power Consumption (kW
hour)
Water Consumption
(liters)
Daily
18
64 - 92
100 - 121
111 - 178
30
164
50
94
0.45
0.80 - 0.99
1.13 - 1.46
1.30 - 1.95
0.88
0.90
1,31
1.38
7.7
10.6 - 17.7
10.9 - 18.5
12.3 - 24.6
10.9
9.0
10.7
14.4
Super 50 min. 65oC
Daily 60oC
In case option of ½ Half-load is used, the values in the program list will be as follows.
Program + ½ load
Program Period
(minutes)
Power Consumption (kW
hour)
Water Consumption
(liters)
Pre-washing
Auto Normal
50-60oC
Quick 30 min. 40oC
Eco
18
Auto
'HOLFDWH 3050oC
62 - 80
30
152
50
0.45
0.77 - 0.96
1.10 - 1.43
1.27 - 1.92
0.88
0.87
1,31
1.35
7.7
9,9 -13,7
10.9 - 18.5
11.3 -19.9
.
10.9
9 .0
10 .7
11.1
74 - 101
Auto
Intense 6070oC
113 - 158
82
** Only powder detergent should be used in cycle of prewash programme.
Warning: Short programs do not include a drying step.
The values declared above are the values obtained under laboratory conditions according to relevant standards. These values can change depending on conditions of product’s
use and environment (network tension, water pressure, water input temperature and environment temperature).
GETTING FAMILIAR WITH YOUR MACHINE
1
2
3
9
10
11
4
5
6
7
1.) ON/OFF Button
When pressed on ON/OFF button, the machine is energized
and the light on Start/Standby button goes on.
8
3
2.) Extra Rinse / Dry Button
You can add extra rinsing or drying functions into the
selected program by using extra button.
Once you selected extra rinsing function , the light for extra
rinsing on the left upper - hand side of the indicator will come on ,
and thus washing-rinsing steps will be added into the
selected program, so you can ensure that your dishes will
be extracted cleaner and glosser.
Once you selected, extra drying function, the light for extra drying on the
left lower -hand side of the indicator will come on, and thus the extra heating
and drying steps will be added into the selected program, so you can ensure that
your dishes will be extracted dryer.
.
3.) Extra Hygiene Button
By using this option, washing temperature and periods
during respective cycles may be changed, which ensures
more hygienic washing.
4.) Tablet Detergent Button
Push Tablet Detergent button when using combined
detergent that contains salt, rinse aid and extra functions.
5.) ½ Half Load Button
Using the function ½ , three sorts of washing up can be done
those being lower basket, upper basket and both baskets.
If you have little amount of dishes in your machine
and if you have to wash them, you can also
activate the semi-filling function in some of the
programs additionally. If you have dishes in both baskets,
press the key ½ and select the position in which both
lamps are highlighted.
If you have dishes only in the upper basket, pres the
key ½ and select the position in which the upper lamp
is illuminated. Thus, washing up shall be done only on
the upper basket of your machine. No dishes should certainly be
available in the lower basket while using this feature.
If you have dishes only in the lower basket, press the
key ½ and select the position in which the lower lamp
is illuminated.
26
Thus, washing up shall be done only on the lower basket of your
machine. In using this feature,make sure that there are no dishes
in the upper basket.
Note : If you have used an extra feature on the latest washing
program, this feature will remain active also on the next washing
program. If you do not want to use this feature on the newly
selected washing program, press the selected feature button
again, and check that the lamp on the button goes off.
6.) Door Handle
The door handle is used to open/close the door of your machine.
7.) Programme selector Button
With the program selector button, you can select a suitable
program for your dishes.
8.) Start/Pause Button
Once you press the Start/Pause button, the programme you
selected with the programme selector button will start running and
the status indicator lamp “wash” will light up.In the stop
condition while wash led is On, Start/Pause led will blink.
9.) Salt Lack Warning indicator
In order to see whether softening salt in your machine is sufficient
or not, check salt lack warning light on the display.When salt light
warning light starts coming on, you need to fill in the salt
chamber.
Rinse aid Lack Warning indicator
In order to check that there is sufficient rinse aid in your machine
check rinse aid lack warning light on the display.When rinse aid
warning light starts coming on , fill in rinse aid chamber.
10.) Program Monitor Lights
Program flow can be monitored via program monitor lights on
control panel.
•
Wash
Rinse
•
•
Dry
•
End
11.) Remaining Time Indicator
Remaining Time Indicator displays the program times and
remaining time during the program is in operation. In addition, you
can adjust program delay time by pressing the buttons on the
indicator before program starts. If you want to change delay time,
you can set the time by pressing St
art/Pause button and using
buttons on the indicator. Press Start/Pausebutton again in order
to activate.
Child Lock Operation
In order to activate child lock, press “+” and “–” buttons on
R e m a i n i n g t im e i n d ic a t o r s im u lt a n e o u s l y 3 f o r s e c o n d s . A t t h is
time, "CL" appears for 2 seconds on remaining time indicator.To
inactive child lock, press “+” and “–” buttons again simultaneously
for 3 seconds. "CL" will blink for 1 times.
27
SWITCHING ON THE MACHINE AND SELECTING A PROGRAMME
Switching on the machine
The lamp on Program Start/Pause key
goes off once the Program starts and
the washing lamp is highlighted.
1. Press the Power On/Off key.
2. Select the program suiting your
dishes via the Program Selector
button.
Once the Power On/Off key
is pressed, the lamp Power
Start/Pause is highlighted.
3. If you prefer or wish to prefer,
you can choose additional
function.
4 Start the program pressing
4.
the Power Start/Pause key.
Program follow-up
You can follow the program flow using the program follow-up lamps located on the control panel.
As long as washing continues, the
lights of washing,rinsing and
drying are on respectively.
Machine remains silent for about
40-50 minutes when the drying
lamp is on.
Once the program is over, the
lamp Finished is illuminated.
Do not open the cover before
the lamp Finished is on.
Changing a programme
If you would like to change programs while a washing program is continuing.
After the program stops, select
your desired program via the
Program selector button.
Press once the Power
Start/Pause key.
28
The new program started
will resume the course of
the old program.
Start the program you have
newly selected by pressing
again the Start/Pause key.
Changing a programme with resetting
If you would like to cancel a program while a washing program is resumed.
Hold Start/Pause button
pressed for approx. 3 sec.
until Finish light blinks.
Once Finish light comes on,
it means that the cycle
has been cancelled.
After Finish light starts blinking,
discharges the water
inside for approx. 30sec.
Switching the machine off
Pull the plug out of the outlet.
Turn of the water tap.
When the lamp “End” lights up,
switch your machine off by using
the Power On/Off button.
Note: You can slightly open the door in order for the machine to perform a faster dry operation after
the wash programme is finished.
Note: If the machine door opens during washing or the power is cut off, the machine will go on to the
program in case the door is shut or the power is back.
Note : If energy is cut or machine door is opened during drying process, program is terminated.
Your machine becomes ready for new program selection.
29
MAINTENANCE AND CLEANING
Cleaning the machine in regular intervals prolongs the machine’s service life.
Oil and lime may accumulate in the machine’s washing section. In case of such accumulation;
-Fill the detergent compartment without loading any dishes into the machine, select a programme that
runs at high temperature, and start the machine. In case of insufficiency, use special cleansing
material available in the market. (Cleansing material produced special to machines by detergent
producers.)
Cleaning the seals in the machine door,
-To clean any accumulated residues in the door seals, wipe the seals regularly by using a dampened
cloth.
Cleaning the machine,
Clean the filters and spray arms at least once a week.
Unplug your machine and turn off its tap before starting the cleaning.
Do not use hard materials when cleaning your machine. Wipe with a fine cleaning material and a
dampened cloth.
Filters
Check if any food wastes have remained on the coarse and fine filters.
If any food wastes are left, remove the filters and clean them
thoroughly under the water tap.
a. Micro Filter
b. Coarse Filter
c. Metal/Plastic Filter
To remove and clean the filter
combination, turn it counter clockwise
and take it out by lifting upwards.1
Pull and remove the metal/plastic filter. 3
Then pull the coarse filter out of the micro
filter.2 Rinse it with lots of water under
the tap. Refit the metal/plastic filter. Insert
the coarse filter into the micro filter in a
way that the marks will correspond to one
another. Attach micro filter into the
metal/plastic filter and turn to the
direction of arrow and it is locked when
the arrow on micro filter can be seen
from across. 4
•
•
•
Never use your dishwasher without any filter.
Incorrect fitting of the filter will reduce the washing effectiveness.
Clean filters are very important in terms of the proper running of the
machine.
30
Spray arms
Check whether or not the holes for the upper and
lower spray arms are clogged. If there is any
clogging, remove the spray arms and clean them
under water.
You can remove the lower spray arm by pulling it
upwards, while the upper spray arm nut can be
removed by turning the nut to the left.
Be sure that the nut is perfectly tightened when
refitting the upper spray arm.
Hose filter
Water is prevented by the inlet hose filter so as to avoid any damage to your machine because of any
contamination (sand, clay, rust etc.) that might be occasionally carried in through the mains water
supply or the indoor plumbing, and to forestall such complaints as yellowing and formation of deposits
after washing. Check the filter and the hose from time to time and clean them if necessary. To clean
the filter, first turn off your tap and then remove the hose. After removing the filter from the hose, clean
it under the tap. Insert the cleaned filter back into its place inside the hose. Refit the hose.
31
32
F6
F9
F7
FE
F1
F8
F2
F3
F5
ERROR CODE
If the error continues, contact the service.
Power off-on your machine and activate the program cancellation command.
The filters of your machine might be clogged.
Water discharge hose is clogged.
Contact the service.
Contact the service.
Contact the service.
Overheating error (temperature in the machine is
too high)
Divisor position error
Faulty heater sensor
Contact the service.
Power off your machine and close the tap.
Contact the service.
•
•
Contact the service.
•
•
•
•
Close the tap.
•
•
Contact the service.
Restart your machine, contact the service if the error resumes.
Close the water input tap, separate the water input hose from the tap and clean the filter at
the connection end of the hose.
Make sure the water input tap is totally open and that there is no water cut.
•
•
•
CONTROL
Faulty electronic card
Alarm is active against water overflow
Heater error
The waste water in the machine cannot be
discharged.
Error of continuous water input
Inadequate water supply
ERROR DESCRIPTION
FAILURE CODES AND WHAT TO DO IN CASE OF FAILURE
If one of program monitor lights is on and start/Pause light is on and off,
Your machine’s door is open, shut the door.
If the programme won’t start
•
Check if the plug is connected.
•
Check your indoor fuses.
•
Be sure that the water inlet tap is turned on.
•
Be sure that you have closed the machine door.
•
Be sure that you switched off the machine by pressing the Power On / Off button.
•
Be sure that the water inlet filter and the machine filters are not clogged.
If the control lamps won’t go out after a wash operation
The Power On/Off button is released yet.
If detergent residues are left in the detergent compartment
Detergent has been added when the detergent compartment was wet.
If water is left inside the machine at the end of the programme
•
The water drain hose is clogged or twisted.
•
The filters are clogged.
•
The programme is not finished yet.
If the machine stops during a wash operation
•
Power failure.
•
Water inlet failure.
•
Program can be on standby mode.
If shaking and hitting noises are heard during a wash operation
•
Dishes placed incorrectly.
•
Spray arm hitting the dishes.
If there are partial food wastes left on the dishes
•
Dishes placed incorrectly into the machine, sprayed water did not reach related places.
•
Basket overly loaded.
•
Dishes leaning against one another.
•
Very small amount of detergent added.
•
An unsuitable, rather weak wash programme selected.
•
Spray arm clogged with food wastes.
•
Filters clogged.
•
Filters incorrectly fitted.
•
Water drain pump clogged.
If there are whitish stains on the dishes
•
A very small amount of detergent is being used.
•
Rinse aid dosage setting at a very low level.
•
No special salt is being used despite the high degree of water hardness.
•
Water softener system setting is at a very low level.
•
Salt compartment cap not closed well.
33
If the dishes won't dry up
•
A programme without a dry operation selected.
•
Rinse aid dosage set too low
•
Dishes unloaded too fast.
If there are rust stains on the dishes
•
Stainless-steel quality of the dishes washed is insufficient.
•
High rate of salt in the wash water.
•
Salt compartment cap not closed well.
•
Too much salt spilt into the sides and into the machine while filling it with salt.
•
Unhealthy mains grounding.
Call an authorised service if the problem still persists after the controls or in case of any
malfunction not described above.
PRACTICAL AND USEFUL INFORMATION
1. Whenever you will not be operating your machine
•
Unplug the machine and then turn the water off.
•
Leave the door slightly ajar in order to prevent the formation of unpleasant smells.
•
Keep the machine interior clean.
2. Eliminating water droplets
•
Wash the dishes with the intensive programme.
•
Take all of the metal containers in the machine out.
•
Do not add detergent.
3. If you properly place your dishes into the machine, you will be using it in the best way in terms
of energy consumption, washing and drying performance.
4. Clean all rough waste before you place dirty dishes to the machine.
5. Operate the machine after it is completely full.
6. Use pre-washing program only when necessary.
7. Observe program information and average consumption values table when selecting a
program.
8. Since the machine will reach high temperatures, it should not be mounted near refrigerator.
9. If the appliance is located in a place where the risk of freezing exists, you must completely drain
the water that has remained in the machine. Turn off the water tap, disconnect the water inlet hose
from the tap and allow the interior water to drain.
34
52191551 R23