The IMPRESSA S9 One Touch Classic Manual - Jura

Figure: Your machine may look
different to the one shown.
The IMPRESSA S9 One Touch Classic Manual
KE
For your safety: read and understand manual before use.
Table of contents
Your IMPRESSA S9 One Touch Classic
IMPORTANT SAFEGUARDS
4
Control elements
8
1 IMPRESSA S9 One Touch Classic
10
JURA on the Internet......................................................................................................................................11
2 Preparing and using for the first time
12
Setting up.......................................................................................................................................................12
Filling the water tank....................................................................................................................................12
Bean container filling....................................................................................................................................12
First-time use.................................................................................................................................................13
Using and activating filter...........................................................................................................................14
Determining and adjusting the degree of water hardness...................................................................16
Adjusting grinder..........................................................................................................................................17
Switching on..................................................................................................................................................17
Switching off (standby)................................................................................................................................18
3 Familiarizing yourself with the control options
19
Preparation at the touch of a button........................................................................................................20
One-off settings before and during preparation....................................................................................20
Entering a permanent setting for the amount of water for a cup size...............................................21
Permanent settings in programming mode........................................................................................... 22
Viewing information and maintenance status.......................................................................................24
4 Preparation at the touch of a button
25
Espresso.........................................................................................................................................................25
Coffee.............................................................................................................................................................26
Coffee à la Carte...........................................................................................................................................26
Cappuccino................................................................................................................................................... 27
Latte macchiato............................................................................................................................................ 27
Pre-ground coffee........................................................................................................................................28
Hot milk and milk foam..............................................................................................................................29
Hot water ......................................................................................................................................................30
5 Permanent settings in programming mode
31
Products..........................................................................................................................................................31
Energy-saving mode (Energy Save Mode, E.S.M.©)............................................................................... 33
Time and weekday.......................................................................................................................................34
Programmable switch-on and switch-off time.......................................................................................35
Automatic switch-off...................................................................................................................................36
Rinses............................................................................................................................................................. 37
Unit amount of water / time format.........................................................................................................38
Language.......................................................................................................................................................39
6Maintenance
40
Maintenance tips..........................................................................................................................................40
Rinsing the machine.....................................................................................................................................41
Changing the filter........................................................................................................................................41
2
Table of contents
Cleaning the machine.................................................................................................................................43
Descaling the machine................................................................................................................................45
Rinsing the cappuccino frother.................................................................................................................48
Cleaning the cappuccino frother...............................................................................................................49
Disassembling and rinsing the Professional Cappuccino Frother.......................................................50
Cleaning the bean container.......................................................................................................................51
Descaling the water tank.............................................................................................................................51
7 Display messages
52
8Troubleshooting
54
9 Transport and environmentally neutral disposal
56
Transport / Emptying the system..............................................................................................................56
Disposal..........................................................................................................................................................56
10 Technical data
57
Index
58
JURA contact details / Legal information
60
Symbol description
Warnings
J
J DANGER
This is the safety alert symbol. lt is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
J WARNING WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
J CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous situation
which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal injury.
Symbols used
T
Prompt to take action. This symbol means that you are being prompted to
perform some action.
E
Information and tips to make it even easier to use your IMPRESSA.
COFFEE
Display message
3

IMPORTANT SAFEGUARDS
Follow the basic safety
precautions
When using electrical appliances, basic safety precautions shall
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
ZZ Read all instructions.
ZZ Do not touch hot surfaces. Use handles or knobs.
ZZ To protect against fire, electric shock and injury to persons, do
not immerse power cord, plugs, or body of machine in water
or other liquid.
ZZ Close supervision is necessary when any appliance is used by
or near children.
ZZ Unplug from outlet when not in use and before cleaning.
Allow to cool before putting on or taking off parts, and before
cleaning the appliance.
ZZ Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
ZZ The use of an accessory attachment not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
ZZ Do not use outdoors.
ZZ Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
ZZ Do not place on or near a hot gas or electric burner, or in a
heated oven.
ZZ Always attach plug to appliance first, then plug cord into the
wall outlet. To disconnect, turn any control to ‘OFF’ then
remove plug from wall outlet.
ZZ Do not use appliance for other than intended use.
ZZ Use extreme caution when dispensing hot steam, hot water
or hot coffee.
ZZ For household use only.
SAVE THESE INSTRUCTIONS.
Pass them on to any subsequent user.
4

Intended use
The appliance is designed and intended for household use only. It
shall only be used for coffee preparation and to heat milk and water,
according to these instructions. Use for any other purpose will be
deemed improper. JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper use.
People, including children, who
ZZ do not have the physical, sensory or mental capabilities to use
the appliance safely or
ZZ are inexperienced or lack knowledge in how to use the appliance safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Special power cord set
instructions
ZZ The power cord is provided to reduce the risk resulting from
becoming entangled in or tripping over a long cord.
ZZ The cord shall be arranged so that it will not drape over the
counter top or table top where it can be pulled on by children
or tripped over.
ZZ This appliance has a 3-pin grounded plug. As a safety feature,
this plug will fit in a polarized outlet only one way.
ZZ If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
ZZ Do not modify the plug in any way or attempt to defeat this
safety feature.
Do NOT use extension cords.
If the user chooses to use an extension cord,
ZZ the marked electrical rating of the extension cord shall be at
least as great as the electrical rating of the appliance, and
ZZ if the appliance is of the grounded type, the extension cord
shall be a grounding type 3-wire cord, and
ZZ the longer cord shall be arranged so that it will not drape over
the counter top or tabletop where it can be pulled on by children or tripped over.
J WARNING
To reduce the risk of fire or electric shock, DO NOT remove any service covers. DO NOT modify the appliance in any way that is not
described in these instructions. NO user serviceable parts included.
Repair MUST be done by authorized personnel only.
5

In the event of signs of damage, for example if there is a smell of
burning, unplug the machine immediately from outlet and contact
JURA customer service.
J CAUTION
This appliance is for household use. Any servicing other than cleaning and user maintenance shall be performed by an authorized service representative:
ZZ Do not immerse base in water or try to disassemble.
ZZ Do not put the appliance or any individual parts in the dishwasher.
ZZ Check voltage to be sure that the voltage indicated on the
name plate complies with your voltage.
ZZ Never use warm or hot water to fill the water container. Use
cold water only.
ZZ Keep your hands and the cord away from hot parts of the
appliance during operation.
There is a risk of scalds or burns on the spouts and the cappuccino
frother / nozzle.
ZZ Keep children away.
ZZ Do not touch any hot parts. Use the handles or knobs provided.
ZZ Ensure that the cappuccino frother / nozzle is correctly fitted
and clean. If incorrectly fitted or if they become blocked, the
cappuccino frother or its parts might come off.
NOTICE
ZZ Never clean with scouring powders or hard implements.
ZZ Ensure that the ventilation slots are not covered.
ZZ Never pull out the drip tray during the brewing process. Only
pull the drip tray when the display instructs you or when the
appliance is ready for use.
NEVER DO
(or you will void your
warranty protection):
6
ZZ Never fill instant coffee, chocolate mix etc. into the bean con-
tainer or ground coffee funnel (filler funnel for ground coffee).
It will damage the functioning of the brewing chamber.
ZZ Never fill sugar coated coffee beans into the bean container.
In case of doubt, call your dealer.
ZZ Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).

ZZ Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw 3 to 4 hours before filling
them into the bean container.
ZZ Never fill anything but fresh, cold and clean water into the
water tank, except when decalcifying.
ZZ Never use mineral or carbonated water. You can use tap water,
bottled water, spring water and reverse osmosis water.
ZZ Never do anything with the machine which is not described in
these instructions. In case of doubt, call your dealer.
7
Control elements
Control elements
8
1
9
2
10
11
3
12
J HOT
4
J HOT
13
J HOT 14
5
6
7
Figure: Your machine may look different to the one shown.
1
2
3
4
5
6
7
8
Bean container cover
Bean container with aroma preservation
cover
Water tank with handle
Power switch and power cord
(back of machine)
Coffee grounds container
Drip tray
Cup platform
8
9
10
11
12
13
14
Fineness of grind switch
Cup tray
Cover of filler funnel for pre-ground coffee
Filler funnel for pre-ground coffee
Professional Cappuccino Frother
Height-adjustable coffee spout
Hot water spout
Control elements
4
1
5
2
3
Front left
1 Display
2 Rotary Switch cover
3f
Rotary switch
Q
On/off button
c Maintenance button
i
1 Espresso button
4
2 Espressi button
o
1 Coffee button
d
2 Coffees button
e
Coffee à la Carte button
v Pre-ground coffee button
Front right
4 ö Selector switch
a Hot water portion symbol
m
Hot water symbol
p
Cappuccino button
z
Milk portion symbol
n
Milk symbol
q Latte Macchiato button
5 Professional Cappuccino Frother
9
1 IMPRESSA S9 One Touch Classic
1 IMPRESSA S9 One Touch Classic
Coffee that fulfils your
wildest dreams
With the new flagship of the IMPRESSA S range, cappuccino and
latte macchiato are prepared at the touch of a button without you
having to move the cup. With its elegant platinum styling and
­upgraded design, this high-quality product is fully in keeping with
contemporary trends and exudes superiority, solidity and competence. It impressively demonstrates these attributes with each
­coffee specialty that you enjoy.
ZZ One Touch Cappuccino/Latte macchiato: Your IMPRESSA S9
makes a cup of cappuccino at the touch of a button, without
you having to move the cup. Hot milk foam, flowing into the
cup and slowly starting to fill it. Steam which rises, awakening
the anticipation of a delicious specialty. Aromatic coffee,
blending with the milk, pushing up the milk foam topping.
These are the protagonists in a sensuous drama – the drama
of perfect coffee preparation. A latte macchiato can also be
made equally easily and sensuously at the touch of a button.
ZZ Energy-saving mode (Energy Save Mode, E.S.M.©): The
IMPRESSA S9 One Touch Classic actively assists you in saving
energy. With the various stages of the energy-saving mode,
you can adjust the ­energy-saving potential to suit the way you
like to enjoy your beverages. The machine can be completely
disconnected from the power grid at the main switch – for
instance if you are going to be absent for some time.
ZZ Control philosophy: You can ‘navigate’ reliably through all
operating and programming steps simply by turning and
pressing the switch. The information on the plain text and
graphic display is in full view at all times. The focus is on your
personal taste. Simply select the coffee strength, amount of
water and temperature according to your individual prefe­
rences.
10
1 IMPRESSA S9 One Touch Classic
ZZ Professional technology for the home: The active bean monitoring feature of your IMPRESSA S9 banishes the sound of
empty rotating coffee grinders and the inconvenience of
half-full cups once and for all. It always shows you in good
time when the coffee beans need replenishing. The filling ­level
of the 10 oz (280 g) bean container is continuously optically
monitored.
JURA on the Internet
Visit us on the Internet.
@@ At www.jura.com you will find interesting and up-to-date
­information on your IMPRESSA and on every aspect of coffee.
11
2 Preparing and using for the first time
2 Preparing and using for the first time
This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step for your first coffee experience.
Setting up
When setting up your IMPRESSA, please note the following:
ZZ Set the IMPRESSA down on a horizontal surface that is not
sensitive to water.
ZZ Choose a spot for your IMPRESSA which is protected against
overheating.
Filling the water tank
To enjoy perfect coffee we recommend changing the water ­every
day.
NOTICE
Milk, sparkling mineral water or other liquids can damage the water
tank or the machine.
T Only fill the water tank with fresh, cold water.
TT Remove the water tank and rinse it with cold water.
TT Fill the water tank with fresh, cold water and reinsert.
Bean container filling
NOTICE
The bean container has an aroma preservation cover. This will ­ensure
that your coffee beans retain their aroma for longer.
Coffee beans which have been treated with additives (e.g. sugar),
ground coffee or freeze-dried coffee will damage the grinder.
T Only use untreated coffee beans to fill the bean container.
TT Open the cover of the bean container and remove the aroma
preservation cover.
TT Remove any dirt or foreign objects inside the bean con­
tainer.
TT Fill the bean container with coffee beans, then close the
­aroma preservation cover and the bean container cover.
12
2 Preparing and using for the first time
First-time use
J WARNING
If the machine is operated with a defective power cord, there is a
danger of potentially fatal electric shock.
T Never use a machine which is damaged.
T Never use a machine which has a defective power cord.
EE The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Unit for amount of
water’).
Precondition: The water tank and bean container are full.
TT Insert the power plug into a power socket.
3TSwitch on the IMPRESSA using the power switch on the back
of the machine.
The on/off button Q lights up (standby).
QTPress the on/off button to switch the IMPRESSA on.
The pre-set language appears on the display.
TT Open the cover of the Rotary Switch.
gTTurn the Rotary Switch until the desired language is displayed. For Example: LANGUAGE ENGLISH
kTPress the Rotary Switch to confirm the language.
CONFIRMED √ appears briefly on the display to confirm
the setting.
TIME --:-gTTurn the Rotary Switch to set the hour.
TIME 12:00 (example)
kTPress the Rotary Switch to confirm the hour setting.
TIME 12:00
gTTurn the Rotary Switch to set the minutes.
TIME 12:45 (example)
kTPress the Rotary Switch to confirm the minute setting.
CONFIRMED √ appears briefly on the display.
WEEKDAY MONDAY
gTTurn the Rotary Switch to set the weekday.
WEEKDAY WEDNESDAY (example)
13
2 Preparing and using for the first time
kTPress the Rotary Switch to confirm the setting.
CONFIRMED √ appears briefly on the display.
FILL SYSTEM / PRESS RINSE, the maintenance
button c lights up.
TT Place a receptacle under the hot water spout and another
under the frother.
cTPress the maintenance button.
SYSTEM FILLS, the system fills up with water and the
maintenance button flashes. A small amount of water flows
from the frother and the hot water spout.
This operation stops automatically. WELCOME TO JURA
appears on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
TT Place a receptacle under the coffee spout.
cTPress the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
EE After first-time use do not disconnect the IMPRESSA from the
power grid for 24 hours to ensure that it is in the optimum
operating condition.
EE When a coffee specialty has been prepared for the first time,
it is possible that FILL BEANS is shown on the display as
the grinder has not yet been completely filled with coffee
beans. In this case prepare a different coffee specialty.
EE If you have not been able to use the machine for the first time
correctly and fully, contact customer support in your country
(see ‘JURA contact details / Legal information’).
Using and
activating filter
Your IMPRESSA no longer has to be descaled if you are using
CLEARYL filter cartridges.
EE Perform the ‘Insert filter’ operation without interruptions. This
will ensure that your IMPRESSA always produces its best.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
14
2 Preparing and using for the first time
kTKeep the Rotary Switch pressed until MAINTENANCE
appears on the display.
gTTurn the Rotary Switch until FILTER NO is displayed.
kTPress the Rotary Switch to enter the program item.
FILTER NO
gTTurn the Rotary Switch until FILTER YES is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display to confirm
the setting.
INSERT FILTER / PRESS RINSE, the maintenance
button c lights up.
TT Remove a CLEARYL filter cartridge and the filter cartridge
extension from the Welcome Pack.
TT Fit the extension on top of the filter cartridge.
TT Remove the water tank and empty it.
TT Lift the cartridge holder and insert the filter cartridge into
the water tank, applying slight pressure.
TT Close the cartridge holder. It will click into place audibly.
TT Fill the water tank with fresh, cold water and reinsert.
TT Place a receptacle (at least 17 oz or 500 ml) under the frother.
EE If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
cTPress the maintenance button.
FILTER RINSING, water flows out of the frother.
EE You can interrupt rinsing of the filter at any time by pressing
any button.
EE The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 17 oz (500 ml).
COFFEE READY appears on the display. The filter is now
activated.
15
2 Preparing and using for the first time
Determining and
adjusting the degree
of water hardness
Level
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH.
Display German Degrees of general Parts per
Indicator Strip number
Degree (°dH)
hardness (°dGH)
million (ppm) of ‘reddish’ fields
Not active
–
–
–
–
Very soft water
<3
<3
< 53.4
None
Soft water
>4
>4
> 71
1
Hard water
> 8.4
> 8.4
> 150
2
Very hard water
> 14
> 14
> 250
3
EE However, if you are using the CLEARYL filter cartridge and have
activated it, you will not be able to adjust the water h
­ ardness.
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
TT Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
TT Wait for about one minute.
TT You will then be able to read the degree of water hardness
from the discoloration of the Aquadur® test strip and the
description on the packaging.
You can now adjust the water hardness.
Example: To change the water hardness from 16°dH to 25°dH,
proceed as follows:
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
gTTurn the rotary switch until HARDNESS 16°dH is
­displayed.
kTPress the Rotary Switch to enter the program item.
16°dH
gTTurn the Rotary Switch until 25°dH is displayed.
16
2 Preparing and using for the first time
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
HARDNESS 25°dH
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY is shown on the display.
Adjusting grinder
NOTICE
You can adjust the grinder continuously to suit the roast of your
coffee.
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.
The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.
Example: To change the fineness of grind during coffee preparation,
proceed as follows:
TT Open the cover of the bean container.
TT Place a cup under the coffee spout.
oTPress the 1 Coffee button.
The grinder starts and 1 COFFEE is displayed.
TT Turn the fineness of grind switch to the desired position
while the grinder is running.
The coffee will be prepared and the fineness of grind is
adjusted.
Switching on
When the IMPRESSA is switched on, a prompt for the rinse operation
automatically appears which is initiated by pressing the maintenance button.
This setting can be changed in programming mode so that the
­machine automatically activates the switch-on rinse (see Chapter 5
‘Permanent settings in programming mode – Rinses’).
Precondition: Your IMPRESSA is switched on at the power switch
and the on/off button Q is illuminated (standby).
17
2 Preparing and using for the first time
QTPress the on/off button to switch the IMPRESSA on.
WELCOME TO JURA appears briefly on the display.
HEATING UP
PRESS RINSE, the maintenance button c lights up.
TT Place a receptacle under the coffee spout.
cTPress the maintenance button.
The machine rinses itself, stopping automatically.
COFFEE READY appears on the display. Your IMPRESSA
is ready to use.
Switching off (standby)
When you switch your IMPRESSA off, the spouts with which a coffee
specialty or milk have been prepared are rinsed.
TT Place a receptacle under the coffee spout and the frother.
QT
Press the on/off button.
MACHINE RINSING appears on the display, and the
coffee spout is rinsed.
SPOUT RIGHT / PRESS RINSE.
cTPress the maintenance button.
MACHINE RINSING, the right coffee spout is rinsed.
EE When you prepare a milk product, but have not performed
cappuccino cleaning, CLEAN CAPPUCCINO appears and
the maintenance button c lights up. For ten seconds you can
start the ‘Clean cappuccino frother’ procedure by pressing the
maintenance button c.
The IMPRESSA is switched off (standby mode), and the
on/off button Q lights up.
EE When your IMPRESSA is switched off, a hissing noise may be
audible. This is normal and does not have any effect on the
machine.
18
3 Familiarizing yourself with the control options
3 Familiarizing yourself with the control options
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
With the IMPRESSA, you can prepare an excellent coffee or milk specialty at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
This chapter will allow you to become familiar with all control
­options with the aid of examples. To familiarize yourself with your
­IMPRESSA, we recommend that you make a point of actively trying
the facilities described in this chapter. You will find this is well worthwhile.
Learn how to perform the following:
ZZ Preparation at the touch of a button
ZZ One-off settings before and while your drink is being prepared
ZZ Adjusting the default amount of water to suit the cup size
ZZ Permanent settings in programming mode
EE You can stop the machine at any time while a coffee or milk
specialty or hot water is being prepared. To do this, press any
button.
EE The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 5 ‘Permanent settings in programming mode – Unit for amount of
water’).
19
3 Familiarizing yourself with the control options
Preparation at the
touch of a button
Prepare your favourite coffee specialty at the touch of a button.
All coffee specialties are prepared following this model.
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
TT Place a cup under the coffee spout.
oTPress the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
­ OFFEE READY is then displayed.
C
EE To prepare 2 coffees, place two cups under the coffee spout
and press the 2 Coffees button d.
One-off settings before
and during preparation
It is possible to make various settings before and during preparation.
These one-off settings are always follow the same model and are not
stored.
Changing the coffee
strength before preparation
The coffee strength of Coffee à la Carte can be changed before
preparation. The following coffee strength options can be selected:
ZZ ö (xmild)
ZZ öö (mild)
ZZ ööö (normal)
ZZ öööö (strong)
ZZ ööööö (xstrong)
Example: Proceed as follows to to prepare a strong cup of Coffee à
la Carte.
Precondition: COFFEE READY is displayed.
TT Place a cup under the coffee spout.
TT Open the cover of the Rotary Switch.
eTPress the Coffee à la Carte button.
A LA CARTE and the pre-set coffee strength is displayed.
gTTurn the Rotary Switch until A LA CARTE öööö is
­displayed.
kTTurn the Rotary Switch while A LA CARTE öööö is
­displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
20
3 Familiarizing yourself with the control options
appears on the display. COFFEE READY is then displayed.
Changing the amount of
water during preparation
The pre-set amount of water of all coffee products can be changed
during the brewing operation by turning the Rotary Switch.
Example: Proceed as follows to prepare a 110 ML cup of coffee.
Precondition: COFFEE READY is displayed.
TT Place a cup under the coffee spout.
TT Open the cover of the Rotary Switch.
oTPress the 1 Coffee button.
1 COFFEE and the pre-set coffee strength is displayed.
The brewing operation starts and the coffee flows into the
cup.
gTTurn the Rotary Switch during the brewing operation until
1 COFFEE / 110 ML is displayed.
The set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
­ OFFEE READY is then displayed.
C
Entering a permanent
setting for the amount
of water for a cup size
It is easy to make permanent settings for the amount of water for all
coffee specialties, cappuccino, latte macchiato, a portion of hot
­water and portion of milk according to the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed.
Making the permanent settings for the amount of water for the
­respective cup size always follows this model.
Example: To make permanent settings for the amount of water for
an espresso, proceed as follows:
Precondition: COFFEE READY is displayed.
TT Place an espresso cup under the coffee spout.
iTPress and hold the 1 Espresso button.
1 ESPRESSO and the coffee strength is displayed.
iTHold the Espresso button down until ENOUGH COFFEE?
appears.
iTRelease the 1 Espresso button.
Coffee preparation will start and the espresso will flow into
the cup.
21
3 Familiarizing yourself with the control options
TT Press any button as soon as enough espresso has flowed
into the cup.
Preparation stops automatically. CONFIRMED w appears
briefly on the display. The set amount of water for an espresso will be permanently stored. COFFEE READY is then
displayed.
EE You can alter these settings at any time by repeating the
above procedure.
Permanent settings in
programming mode
You can easily adjust your IMPRESSA to your personal coffee blends
and specialties. You can navigate through the easy-to-understand
program steps and make permanent settings simply by turning and
pressing the Rotary Switch.
You can make the following permanent settings with the Rotary
Switch:
Program item
Subitem
Explanation
MAINTENANCE CLEAN CAPPUCCINO,
RINSE MACHINE,
RINSE CAPPUCCINO,
CLEAN MACHINE,
DECALCIFY MACHINE,
CHANGE FILTER
TT Select the desired maintenance program.
If no action is taken, programming mode
is exited in the MAINTENANCE program
item automatically after approx. five seconds.
PRODUCTS
TT Select your settings for the coffee and milk
specialties and hot water.
FILTER
FILTER YES,
FILTER NO
TT Indicate whether you operate your
IMPRESSA with or without a CLEARYL
filter cartridge.
HARDNESS
1°dH – 30°dH
TT Adjust the water hardness.
ECONOMY
MODE
Save NO,
Save LEVEL 1,
SAVE LEVEL 2
TT Select an energy-saving mode.
TIME
--:--, WEEKDAY
TT Set the time and weekday.
(is only displayed
when the filter is
not activated)
22
3 Familiarizing yourself with the control options
Program item
Subitem
Explanation
TT Set the switch-on and switch-off time
individually for each weekday.
UNIT ON/OFF
OFF AFTER
OFF AFTER -- H,
0.5 H – 15 H
TT Set the number of hours after which the
IMPRESSA should switch off automatically.
RINSES
INIT RINSE,
CAPP RINSE
TT Set whether the switch-on rinse should be
started manually or automatically.
TT Set whether the prompt for cappuccino
rinsing should be started immediately or
10 minutes afterpreparation of a milk
specialty.
TT Keep track of all prepared coffee and milk
specialties and view the maintenance status.
INFORMATION
SETTINGS
ML/OZ,
24HRS/AM PM
TT Select the unit of the amount of water and
the time format.
LANGUAGE
TT Select the desired language.
EXIT
TT Exit programming mode.
Settings in programming mode always follow the same model.
Example: To change the strength of one espresso from
ööö ­(normal) to öööö (strong).
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
gTTurn the Rotary Switch until PRODUCTS is displayed.
kTPress the Rotary Switch to enter the program item.
SELECT PRODUCT
EE Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
iTPress the 1 Espresso button.
WATER 45 ML
gTTurn the Rotary Switch until AROMA ööö is displayed.
kTPress the Rotary Switch to enter the program item.
NORMAL ööö
23
3 Familiarizing yourself with the control options
gTTurn the Rotary Switch until STRONG öööö is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
AROMA öööö
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
SELECT PRODUCT
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
PRODUCTS
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Viewing information
and maintenance
status
Under the program item INFORMATION you can query the following information:
ZZ Number of the prepared coffee and milk specialties
ZZ Maintenance status and number of maintenance programs
performed (cleaning, descaling, filter change)
ZZ Number of performed cappuccino cleaning operations
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTPress the Rotary Switch until MAINTENANCE appears.
gTTurn the Rotary Switch until INFORMATION is displayed.
kTPress the Rotary Switch to enter the program item.
TOTAL, the sum of all prepared coffee and milk specialties
is displayed.
gTTurn the Rotary Switch for further information.
EE The respective maintenance status can also be displayed in
addition to the number of performed maintenance programs.
The bar shows the current maintenance status. When the bar
is filled completely, your IMPRESSA will request the respective
maintenance program.
kTPress the Rotary Switch to exit the program item.
INFORMATION
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
24
COFFEE READY
4 Preparation at the touch of a button
4 Preparation at the touch of a button
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
In this chapter you will find out how to prepare coffee and milk specialties and hot water without making further settings.
Chapter 3, ‘Familiarizing yourself with the control options’, will teach
you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’.
EE You can stop the machine at any time while a coffee or milk
product or hot water is being prepared. To do this, press any
button.
EE During preparation, you can change the pre-set amount of
water by turning the Rotary Switch.
EE The water volume is given as standard in ‘oz’. You can change
this setting to ‘ml’ in programming mode (see Chapter 5 ‘Permanent settings in programming mode – Unit for amount of
water’).
Espresso
The classic coffee drink from Italy. There is a definite crema on the
surface of the espresso.
Example: This is how to prepare one espresso.
Precondition: COFFEE READY is displayed.
TT Place an espresso cup under the coffee spout.
iTPress the 1 Espresso button.
1 ESPRESSO and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
­ OFFEE READY is then displayed.
C
25
4 Preparation at the touch of a button
EE To prepare two espressi place two cups under the coffee
spout and press the 2 Espressi button 4.
Coffee
Example: This is how to prepare one coffee.
Precondition: COFFEE READY is displayed.
TT Place a coffee cup under the coffee spout.
oTPress the 1 Coffee button.
1 COFFEE and the pre-set coffee strength are displayed.
The pre-set amount of water flows into the cup. Preparation
stops automatically. ENJOY appears on the display.
­ OFFEE READY is then displayed.
C
EE To prepare 2 coffees, place two cups under the coffee spout
and press the 2 Coffees button d.
Coffee à la Carte
The coffee strength of Coffee à la Carte can be changed before
­preparation.
Example: Proceed as follows to prepare a strong (öööö) cup of
Coffee à la Carte.
Precondition: COFFEE READY is displayed.
TT Place a cup under the coffee spout.
TT Open the cover of the Rotary Switch.
eTPress the Coffee à la Carte button.
A LA CARTE ö
gTTurn the Rotary Switch until A LA CARTE öööö is
­displayed.
kTPress the Rotary Switch while A LA CARTE öööö is
­displayed.
A LA CARTE öööö, the pre-set amount of water flows
into the cup. Preparation stops automatically. ENJOY
appears on the display. COFFEE READY is then displayed.
26
4 Preparation at the touch of a button
Cappuccino
Your IMPRESSA prepares a cappuccino at the touch of a button. It is
not necessary to move the cup.
Precondition: COFFEE READY is displayed.
TT Take the protective cover off the Professional Cappuccino
Frother.
TT Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
TT Insert the other end into a milk carton/bottle or connect it to
the milk container.
TT Place a cup under the frother.
TT Turn the selection lever of the frother to the milk foam
­position p.
pTPress the Cappuccino button.
CAPPUCCINO and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when the pre-set amount of milk is reached.
Coffee preparation then begins. The pre-set amount of
­water flows into the cup.
Preparation stops automatically. ENJOY appears on the
display. COFFEE READY is then displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Latte macchiato
Your IMPRESSA prepares a latte macchiato at the touch of the
­button. It is not necessary to move the glass.
Precondition: COFFEE READY is displayed.
TT Take the protective cover off the Professional Cappuccino
Frother.
TT Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
TT Insert the other end into a milk carton/bottle or connect it to
the milk container.
27
4 Preparation at the touch of a button
TT Place a glass under the frother.
TT Turn the selection lever of the frother to the milk foam
­position p.
qTPress the Latte Macchiato button.
LATTE MAC. and the coffee strength are displayed.
The milk foam is then prepared. The operation stops automatically when pre-set amount of milk is reached.
EE A brief pause follows during which the hot milk separates from
the milk foam. This enables the formation of the typical layers
of a latte macchiato. The duration of this pause can be defined
in programming mode.
Coffee preparation then begins. The pre-set amount of
­water flows into the glass. Preparation stops automatically.
ENJOY appears on the display. COFFEE READY is then
displayed.
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Pre-ground coffee
You can choose a second coffee blend, for example decaffeinated
coffee, with the filler funnel for pre-ground coffee.
EE Never add more than two level measuring spoons of preground coffee.
EE Use pre-ground coffee which is not ground too finely. Very
fine coffee can block up the system so that the coffee only
comes out in drips.
EE If you did not fill the machine with a sufficient amount of preground coffee, NOT ENOUGH PRE-GROUND is displayed
and the IMPRESSA stops operation.
All coffee specialties with pre-ground coffee are prepared following
this model.
Example: This is how to prepare a cup of coffee using pre-ground
coffee.
TT Place a cup under the coffee spout.
28
4 Preparation at the touch of a button
TT Open the cover of the filler funnel for pre-ground coffee.
TT Open the cover of the Rotary Switch.
vTPress the Pre-ground coffee button.
FILL PRE-GROUND / COFFEE READY
TT Place one level measuring spoon of pre-ground coffee into
the filler funnel.
TT Close the cover of the filler funnel for pre-ground coffee.
oTPress the 1 Coffee button.
1 COFFEE, the pre-set amount of water flows into the
cup. Preparation stops automatically. ENJOY appears on
the display. COFFEE READY is then displayed.
Hot milk and milk
foam
There are two options for preparing hot milk or milk foam:
ZZ Milk portion z
UU The preset quantity of milk is then prepared.
ZZ Milk n
UU Milk is prepared until preparation is interrupted by pressing
any button.
Precondition: COFFEE READY is displayed.
TT Take the protective cover off the frother.
TT Attach the milk pipe to the frother. For a milk carton/bottle
use the long pipe, for a milk container the short pipe.
TT Insert the other end into a milk carton/bottle or connect it to
the milk container.
TT Place a cup under the frother.
TT Turn the selection lever of the frother to the milk foam
­position p.
EE If you want to heat the milk, set the selection lever of the
frother to the milk position t.
öTWith the selector switch select the milk portion symbol z.
äTPress the selector switch.
MILK, the milk foam is being prepared. Preparation stops
automatically when the pre-set amount of milk is reached.
COFFEE READY is shown on the display.
29
4 Preparation at the touch of a button
To ensure that the frother works perfectly, you should rinse and
clean it regularly. The description for this can be found in Chapter 6
‘Maintenance – Cappuccino frother’.
Hot water
Hot water can be prepared in two ways:
ZZ Hot water portion a
UU The pre-set amount of water flows into the cup.
ZZ Hot water m
UU Water flows out of the hot water spout until preparation is
interrupted by pressing any button.
The following temperatures can be selected for preparing hot
water:
ZZ Low
ZZ Normal
ZZ X high
J CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
Example: This is how to prepare a portion of hot water.
Precondition: COFFEE READY is displayed.
TT Place a cup under the hot water spout.
öTUse the selector switch to select the hot water portion
­symbol a.
äTPress the selector switch.
TEMPERATURE and the pre-set temperature are displayed.
EE By pressing the selector switch several times (within approx.
2 seconds) you can set the temperature to your individual
preference. This setting is not saved.
HOT WATER, the pre-set amount of water flows into the
cup. Preparation stops automatically. COFFEE READY
­appears on the display.
30
5 Permanent settings in programming mode
5 Permanent settings in programming mode
Products
With the PRODUCTS program item you can enter individual settings for all coffee and milk specialties as well as hot water.
J WARNING
Hot coffee, hot steam and hot water can cause scalding. Scalding is
a serious burn.
T Use extreme care when handling hot liquid or steam.
T Allow liquid to cool down before drinking.
T In the event of scalding, rinse affected area with cold water
and seek medical attention.
T Keep children AWAY.
The following permanent settings can be made:
Product
Amount
Coffee strength
Temp.
1 Espresso,
1 Coffee
0.5 OZ – 8.0 OZ (25 ml – 240 ml)
ö (xmild),
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
NORMAL,
HIGH
2 Espressi,
2 Coffees
0.5 OZ – 8.0 OZ (25 ml – 240 ml)
Coffee à la
Carte
0.5 OZ – 8.0 OZ (25 ml – 240 ml)
–
NORMAL,
HIGH
–
NORMAL,
HIGH
(per cup)
Cappuccino, Amount of milk: 3 SEC – 120 SEC
Latte
Pause: 0 SEC – 60 SEC
macchiato
Amount of water: 0.5 OZ – 8.0 OZ
(25 ml – 240 ml)
ö (xmild),
öö (mild),
ööö (normal),
öööö (strong),
ööööö (xstrong)
NORMAL,
HIGH
Milk portion 3 SEC – 120 SEC
–
–
Milk
–
–
–
LOW, NORMAL,
X HIGH
–
LOW, NORMAL,
X HIGH
Hot water
portion
Hot water
–
0.5 OZ – 15.0 OZ
(25 ml – 450 ml)
–
31
5 Permanent settings in programming mode
EE The products which are selected with the selector switch can
be individually set to inactive. This means that the respective
symbols are not visible and preparation is not possible.
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the amount of milk of latte
macchiato from 16 SEC to 20 SEC, the pause from 30 SEC
to 40 SEC and the amount of water from 1.5 OZ (45 ml) to
1.0 OZ (40 ml).
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
gTTurn the Rotary Switch until PRODUCTS is displayed.
kTPress the Rotary Switch to enter the program item.
SELECT PRODUCT
EE Next select the product button for which you would like to
make settings. No product is prepared during this procedure.
qTPress the Latte Macchiato button.
COFFEE 1.5 OZ (45 ml)
kTPress the Rotary Switch to enter the program item.
COFFEE 1.5 OZ (45 ml)
gTTurn the Rotary Switch until COFFEE 1.0 OZ (40 ml) is
displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
COFFEE 40 ML
gTTurn the Rotary Switch until MILK 16 SEC is displayed.
kTPress the Rotary Switch to enter the program item.
MILK 16 SEC
gTTurn the Rotary Switch until MILK 20 SEC is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
MILK 20 SEC
gTTurn the Rotary Switch until PAUSE 30 SEC is displayed.
32
5 Permanent settings in programming mode
kTPress the Rotary Switch to enter the program item.
PAUSE 30 SEC
gTTurn the Rotary Switch until PAUSE 40 SEC is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
PAUSE 40 SEC
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
SELECT PRODUCT
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
PRODUCTS
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Resetting the products to
works settings
You can reset the values of all products as well as cappuccino and
latte macchiato individually to the works setting.
Example: Proceed as follows to reset the values of 1 Espresso to the
works setting.
Precondition: The IMPRESSA is switched off (standby).
TT Open the cover of the Rotary Switch.
TT Press the Rotary Switch and the 1 Espresso button for two
seconds at the same time until 1 ESPRESSO OK
­appears.
The values of 1 Espresso are then reset to the works setting.
The IMPRESSA is switched off (standby).
Energy-saving mode
(Energy Save Mode,
E.S.M.©)
You can also set various energy-saving modes on your IMPRESSA:
ZZ SAVE NO
UU Your IMPRESSA is continuously ready for use.
UU All coffee and milk products, as well as hot water, can be
­prepared without having to wait.
ZZ SAVE LEVEL 1
UU Your IMPRESSA is only continuously ready for use for coffee
products and hot water.
UU The machine has to heat up before milk preparation.
33
5 Permanent settings in programming mode
ZZ SAVE LEVEL 2
UU Approx. 5 minutes after the last preparation the IMPRESSA
switches to the energy-saving temperature and is not ready
for use.
UU Before coffee, hot water or milk can be prepared, the m
­ achine
has to heat up.
Example: Proceed as follows to change the energy-saving mode
from SAVE NO to SAVE LEVEL 1.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
gTTurn the Rotary Switch until ECONOMY MODE - is displayed.
kTPress the Rotary Switch to enter the program item.
SAVE NO
gTTurn the Rotary Switch until SAVE LEVEL 1 is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
ECONOMY MODE 1
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Time and weekday
You already set the time and weekday when you used the machine
for the first time.
Example: To change the time from 08:45 to 09:50, proceed
as follows.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
gTTurn the Rotary Switch until TIME 08:45 is displayed.
kTPress the Rotary Switch to enter the program item.
TIME 08:45
gTTurn the Rotary Switch until TIME 09:45 is displayed.
kTPress the Rotary Switch to confirm the hour setting.
34
5 Permanent settings in programming mode
gTTurn the Rotary Switch until TIME 09:50 is displayed.
kTPress the Rotary Switch to confirm the minute setting.
CONFIRMED w appears briefly on the display.
WEEKDAY MONDAY (Example)
kTPress the Rotary Switch to confirm the weekday setting.
CONFIRMED √ appears briefly on the display.
TIME 09:50
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Programmable
switch-on and
switch-off time
The programmable switch-on and switch-off time can only be set
when the time has been set.
The following settings can be made in the UNIT ON/OFF menu
item:
ZZ UNIT ON
UU Set the required switch-on time.
ZZ MACH. OFF
UU Set the required switch-off time.
ZZ ON/OFF
UU Set the weekdays on which IMPRESSA should switch on and
off automatically.
EE The programmable switch-on only works when the machine
is switched on at the power switch (standby).
Example: Proceed as follows to set the programmable switch-on
time to 07:30 and stipulate that your IMPRESSA does not switch
on automatically on Sundays.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
a­ppears.
gTTurn the Rotary Switch until UNIT ON/OFF is displayed.
kTPress the Rotary Switch to enter the program item.
UNIT ON --:-kTPress the Rotary Switch to enter the program item.
UNIT ON --:-35
5 Permanent settings in programming mode
gTTurn the Rotary Switch until UNIT ON 07:00 is displayed.
kTPress the Rotary Switch to confirm the hour setting.
gTTurn the Rotary Switch until UNIT ON 07:30 is displayed.
kTPress the Rotary Switch to confirm the minute setting.
CONFIRMED w appears briefly on the display.
UNIT ON 07:30
gTTurn the Rotary Switch until ON/OFF / MON YES is displayed.
kTPress the Rotary Switch to enter the program item.
ON/OFF / MON YES
gTTurn the Rotary Switch until ON/OFF / SUN YES is displayed.
kTPress the Rotary Switch to enter the program item.
ON/OFF / SUN YES
gTTurn the Rotary Switch until ON/OFF / SUN NO is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
ON/OFF / SUN NO
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
ON/OFF / MON YES
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
UNIT ON/OFF
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the last action on
the machine.
EE The programmable switch-off time can be adjusted between
0.5 and 15 hours or deactivated.
36
5 Permanent settings in programming mode
Example: Proceed as follows to change the automatic switch-off
time from 1 H to 2 H.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
gTTurn the Rotary Switch until OFF AFTER 1 H is displayed.
kTPress the Rotary Switch to enter the program item.
OFF AFTER 1 H
gTTurn the Rotary Switch until OFF AFTER 2 H is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
OFF AFTER 2 H
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Rinses
You can set whether the switch-on rinse should be started manually or automatically.
You can set whether cappuccino rinsing should be prompted immediately or 10 minutes after a milk product has been prepared.
Example: Proceed as follows to program that Cappuccino rinsing
should be prompted immediately after a milk product has been
prepared.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
gTTurn the Rotary Switch until RINSES is displayed.
kTPress the Rotary Switch to enter the program item.
INIT RINSE MANUAL
gTTurn the Rotary Switch until CAPP RINSE AFTER 10’
is displayed.
kTPress the Rotary Switch to enter the program item.
CAPP RINSE AFTER 10’
37
5 Permanent settings in programming mode
gTTurn the Rotary Switch until CAPP RINSE NOW is
­displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
CAPP RINSE NOW
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
RINSES
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
Unit amount of
water / time format
You can change the unit of the amount of water from ‘ml’ to ‘oz’ and
the time format to ‘24 HRS’ or ‘AM/PM’ .
Example: To change the unit for the amount of water from ML to
OZ, proceed as follows.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
gTTurn the Rotary Switch until SETTINGS 24HRS / ML
is displayed.
kTPress the Rotary Switch to enter the program item.
SETTINGS 24HRS
gTTurn the Rotary Switch until SETTINGS ML is displayed.
kTPress the Rotary Switch to enter the program item.
SETTINGS ML
gTTurn the Rotary Switch until SETTINGS OZ is displayed.
kTPress the Rotary Switch to confirm the setting.
CONFIRMED w appears briefly on the display.
SETTINGS OZ
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit the program item.
SETTINGS 24HRS / OZ
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
COFFEE READY
38
5 Permanent settings in programming mode
Language
You set the language when you used the machine for the first time.
Example: To change the language from ENGLISH to DEUTSCH
(example), proceed as follows.
Precondition: COFFEE READY is displayed.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
gTTurn the Rotary Switch until LANGUAGE ENGLISH is
displayed.
kTPress the Rotary Switch to enter the program item.
LANGUAGE ENGLISH
gTTurn the Rotary Switch until SPRACHE DEUTSCH
(example) is displayed.
kTPress the Rotary Switch to confirm the setting.
GESPEICHERT w (example) appears briefly on the display.
SPRACHE DEUTSCH (example)
gTTurn the Rotary Switch until EXIT is displayed.
kTPress the Rotary Switch to exit programming mode.
BITTE WÄHLEN (example)
39
6 Maintenance
6Maintenance
J WARNING
Use of maintenance products that are harmful to health and discharge of liquids during maintenance program. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Keep children away from the machine while it is performing a
maintenance program.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T When using do not eat or drink.
T Keep maintenance products away from food, drink and animal food.
T Keep container tightly closed and dry. Keep in a cool place.
Your IMPRESSA has the following integrated maintenance programs:
ZZ Rinse machine
ZZ Change filter
ZZ Clean machine
ZZ Decalcify machine
ZZ Rinse cappuccino frother
ZZ Clean cappuccino frother
EE Clean or descale the machine or change the filter whenever
the appropriate prompt is displayed.
Maintenance tips
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the
­
­machine requires daily maintenance.
You should proceed as follows:
ZZ Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
ZZ Rinse the water tank with clean water.
ZZ Dismantle and rinse the frother (see Chapter 6
‘Maintenance – Rinsing the cappuccino frother’).
ZZ Wipe the surface of the machine with a damp cloth.
40
6 Maintenance
Rinsing the machine
When the IMPRESSA is switched on, a prompt to perform a rinse
operation appears after heating, or this is automatically started.
It can be set in programming mode whether the switch-on rinse
needs to be activated manually or whether the machine automatically activates the switch-on rinse (see Chapter 5 ‘Permanent settings in programming mode – Rinses’).
When the IMPRESSA is switched off, a rinse operation is automatically initiated.
You can initiate the rinse operation manually at any time.
Precondition: COFFEE READY is displayed.
TT Place a receptacle under the coffee spout.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
fTTurn the Rotary Switch until RINSE MACHINE is displayed.
kTPress the Rotary Switch to initiate the rinse operation.
MACHINE RINSING
Rinsing stops automatically and your IMPRESSA is then once
more ready for use.
Changing the filter
Change following a prompt
EE After 2000 oz (60 liters) of water have flowed through, the filter will cease to work. Your IMPRESSA will automatically
prompt you to replace the filter.
EE After two months, the filter will cease to work. Monitor the
elapsed time by adjusting the date plate on the cartridge
holder.
EE If the CLEARYL filter cartridge is not activated, you will not be
prompted to change the filter.
To change the CLEARYL filter cartridge when prompted to do so by
your IMPRESSA, proceed as follows:
Precondition: COFFEE READY / CHANGE FILTER is displayed, and the maintenance button c lights up.
41
6 Maintenance
cTPress the maintenance button.
DURATION 2 MIN. / START YES
EE If you want to change the filter at a later point in time, turn the
Rotary Switch until START NO is displayed. Exit the maintenance program by pressing the Rotary Switch. The prompt
‘Change filter’ remains on the display.
cTPress the maintenance button.
CHANGE FILTER / PRESS RINSE
TT Remove the water tank and empty it.
TT Lift the cartridge holder.
TT Take out the old CLEARYL filter cartridge and the extension.
TT Fit the extension on top of a new filter cartridge.
TT Insert the filter cartridge into the water tank, exerting slight
pressure.
TT Close the cartridge holder. It will click into place audibly.
TT Fill the water tank with fresh, cold water and reinsert.
TT Place a receptacle (at least 17 oz or 500 ml) under the frother.
EE If you are using the Professional Cappuccino Frother, set the
selection lever of the frother to the steam position n.
cTPress the maintenance button.
FILTER RINSING, water flows out of the frother.
EE You can interrupt filter rinsing at any time. To do this, press
any button.
EE The water may be slightly discolored. This is not harmful to
health and does not affect the taste.
Filter rinsing stops automatically after approx. 17 oz (500 ml).
The IMPRESSA heats up and is once again ready to use.
Manual filter change
You can initiate the ‘Changing the filter’ operation manually.
Precondition: The filter is activated and COFFEE READY is
shown on the display.
TT Open the cover of the Rotary Switch.
42
6 Maintenance
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
gTTurn the Rotary Switch until CHANGE FILTER is displayed.
kTPress the Rotary Switch.
DURATION 2 MIN. / START YES
TT Continue with the second prompt to take action (indicated
by a T), as is described under ‘Replacement following a
prompt’.
Cleaning the machine
After 220 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
J WARNING
Non-recommended (e.g. liquid) cleaning agents may contain substances that could damage the machine or leave residues.
T Use only original JURA cleaning tablets. These are specially
formulated for your machine.
J WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
EE The cleaning program only lasts about 20 minutes.
EE Do not interrupt the cleaning program. The quality of cleaning
will be impaired if you do so.
EE JURA cleaning tablets are available from specialized dealers.
43
6 Maintenance
Cleaning following
a prompt
Precondition: COFFEE READY / CLEAN MACHINE is displayed, and the maintenance button c lights up.
cTPress the maintenance button.
DURATION 20 MIN. / START YES
EE If you want to clean the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance program by pressing the Rotary Switch. The
prompt ‘Clean machine’ remains on the display.
cTPress the maintenance button.
EMPTY TRAY
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button c lights up.
TT Place a receptacle under the coffee spout and the frother.
cTPress the maintenance button.
CLEANS, the cleaning operation starts.
The process is interrupted. ADD TABLET / PRESS
RINSE, the maintenance button c lights up.
TT Open the cover of the filler funnel for pre-ground coffee.
TT Insert a JURA cleaning tablet into the filler funnel.
TT Close the cover of the filler funnel.
cTPress the maintenance button.
CLEANS, water flows out of the coffee spout and the frother several times.
EE You can follow the current status of cleaning on the progress
bar.
The process is interrupted, EMPTY TRAY.
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
The cleaning operation is now complete. The IMPRESSA is
ready for use again.
Manual cleaning
You can initiate the ‘Cleaning the machine’ operation manually.
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
44
6 Maintenance
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
gTTurn the rotary switch until CLEAN MACHINE is displayed.
kTPress the Rotary Switch.
DURATION 20 MIN. / START YES
TT Continue with the second prompt to take action (indicated
by a T), as is described under ‘Cleaning following a prompt’.
Descaling the machine
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
J WARNING
Non-recommended descaling agents (e.g. vinegar) may contain
substances that could damage the machine or leave residues.
T Use only original JURA descaling tablets. These are specially
formulated for your machine.
J WARNING
Harmful and irritating descaling agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T Avoid generation of dust. Do not inhale dust.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water.
Remove contact lenses. Seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
NOTICE
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling program to run to the end.
EE The descaling program lasts approx. 45 minutes.
EE JURA descaling tablets are available from specialized dealers.
45
6 Maintenance
EE If you use a CLEARYL filter cartridge and this is activated, you
will not be prompted to change the filter.
EE If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. Clean up any
splashes immediately.
Descaling following
a prompt
Precondition: COFFEE READY / DECALCIFY MACHINE is
displayed and the maintenance button c lights up.
cTPress the maintenance button.
DURATION 45 MIN. / START YES
EE If you want to descale the machine at a later point in time, turn
the Rotary Switch until START NO is displayed. Exit the
maintenance program by pressing the Rotary Switch. The
prompt ‘Decalcify machine’ remains on the display.
cTPress the maintenance button.
EMPTY TRAY
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
SOLVENT IN TANK
TT Remove the water tank and empty it.
TT Completely dissolve the contents of one blister (3 JURA descaling tablets) in a container that holds 20 oz (600 ml) of
water. This may take several minutes.
TT Pour the solution into the empty water tank and insert it in
the machine.
SOLVENT IN TANK / PRESS RINSE, the maintenance button c lights up.
TT Remove the frother from the Connector System©.
TT Place a receptacle under the hot water spout and another
under the Connector System©.
cTPress the maintenance button.
DECALCS, water flows out of the Connector System© and
the hot water spout. The maintenance button c flashes
­during the descaling operation.
EE You can follow the current status of descaling on the progress
bar.
The process is interrupted, EMPTY TRAY.
46
6 Maintenance
TT Empty the receptacles below the hot water spout and the
Connector System©.
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
RINSE WATER TANK / FILL WATER TANK
TT Remove the water tank and rinse it thoroughly.
TT Fill the water tank with fresh, cold water and reinsert.
PRESS RINSE, the maintenance button c lights up.
TT Refit the frother.
TT Place a receptacle under the coffee and hot water spout and
another under the frother.
cTPress the maintenance button.
DECALCS, water flows out of the frother and the hot water
spout.
The process is interrupted, HEATING UP.
MACHINE RINSING, water flows out of the coffee
spout. The operation stops automatically, EMPTY TRAY.
TT Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once again ready to use.
EE If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Manual descaling
You can initiate the ‘Descaling the machine’ operation manually.
Precondition: COFFEE READY is shown on the display and the
filter is not activated.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
gTTurn the Rotary Switch until DECALCIFY MACHINE
is displayed.
kTPress the Rotary Switch.
DURATION 45 MIN. / START YES
TT Continue with the second prompt to take action (indicated
by a T), as is described under ‘Descaling following a prompt’.
47
6 Maintenance
Rinsing the
cappuccino frother
Each time milk has been prepared the IMPRESSA displays a prompt
for Cappuccino rinsing.
It can be set in programming mode whether the rinsing prompt is
displayed immediately or 10 minutes after preparation (refer to
Chapter 5 ‘Permanent settings in programming mode – Rinses’).
Rinsing following a prompt
Precondition: COFFEE READY / RINSE CAPPUCCINO is
displayed and the maintenance button c lights up.
TT Place a receptacle under the frother.
EE If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
cTPress the maintenance button.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
­appears on the display.
Starting rinsing manually
You can initiate the ‘Rinsing the cappuccino frother’ operation
­manually.
Precondition: COFFEE READY is displayed.
TT Place a receptacle under the frother.
EE If you are using the Professional Cappuccino Frother, turn
the selection lever to the steam position n.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
gTTurn the Rotary Switch until RINSE CAPPUCCINO is
displayed.
kTPress the Rotary Switch to start the rinse operation.
CAPPU. RINSING, the frother is rinsed.
The procedure stops automatically. COFFEE READY
­appears on the display.
48
6 Maintenance
Cleaning the
cappuccino frother
To ensure that the respective frother works perfectly, you should
clean it daily when you have been preparing milk.
J WARNING
Non-recommended cleaning agents will not optimally remove milk
residues. This may cause the cappuccino frother to become blocked
and fly off the machine. Discharge of hot steam.
T Use only original JURA Cappuccino Cleaner.
J WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.
T Keep children AWAY.
T Avoid contact with skin and eyes.
T After contact with skin, wash immediately with plenty of
water. In case of skin irritation, seek medical advice.
T After eye contact, immediately flush eyes with plenty of water
and seek medical advice.
T If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice
immediately and show label.
EE The IMPRESSA will not prompt you to clean the frother.
EE The JURA Cappuccino Cleaner is available from specialized
dealers.
Cleaning the cappuccino
frother – manually
Precondition: COFFEE READY is displayed.
TT Open the cover of the Rotary Switch.
kTKeep the Rotary Switch pressed until MAINTENANCE
­appears.
kTPress the Rotary Switch to enter the program item.
CLEAN CAPPUCCINO
kTPress the Rotary Switch.
CLEANER FOR CAPPU., the maintenance button c
lights up.
TT Pour 8.5 oz (250 ml) of fresh water into a container and add
one ­capful (max. 0.5 oz (15 ml)) of Cappuccino Cleaner.
TT Immerse the milk pipe in the receptacle with the cleaning
solution.
EE If you are using the Professional Cappuccino Frother, turn
the selection lever to the milk foam p or milk t position.
49
6 Maintenance
TT Place another receptacle under the frother.
cTPress the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are
cleaned.
WATER FOR CAPPUCCINO, the maintenance button c
lights up.
TT Rinse the receptacle thoroughly, fill it with approx. 8.5 oz
(250 ml) of fresh water and immerse the milk pipe in the water.
TT Empty the other receptacle and place it under the frother
once more.
cTPress the maintenance button.
CAPPUCCINO / CLEANS, the frother and pipe are rinsed
with fresh water.
COFFEE READY appears on the display. Your IMPRESSA
is once more ready to use.
Cleaning the cappuccino
frother after a prompt
If milk has been prepared, but the cappuccino frother has not been
cleaned, the CLEAN CAPPUCCINO prompt is displayed when
the machine is switched off. The maintenance program can be
started by pressing the maintenance button c.
Precondition: CLEANER FOR CAPPU. is displayed and the
maintenance button c lights up.
TT Continue with the fifth prompt to take action (indicated
by a T), as is described under ‘Cleaning the cappuccino
frother – manually’.
Disassembling and
rinsing the Professional
Cappuccino Frother
TT Carefully remove the frother from the Connector System©
by twisting slightly.
TT Dismantle the frother completely.
TT Rinse all the frother parts thoroughly under running water.
TT Reassemble the frother.
EE Ensure that the individual parts are correctly and firmly
­attached to one another to ensure optimum function of the
frother.
TT Firmly attach the frother to the Connector System©.
50
6 Maintenance
Cleaning the
bean container
J WARNING
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
Danger of injury to the fingers when the grinder is running.
TT Switch the machine off with the on/off button Q before performing any work on the grinder.
TT Switch the machine off at the power switch 3.
TT Open the cover of the bean container and remove the aroma
preservation cover.
TT Remove the beans with a vacuum cleaner.
TT Loosen the screw in the bean container and lift up the finger
protection.
TT Remove the remaining beans with a vacuum cleaner.
TT Clean the bean container with a soft, dry cloth.
TT Put the finger protection down again and screw it back
­tightly in place.
TT Fill the bean container with coffee beans, then close the
­aroma preservation cover and the bean container cover.
Descaling the water
tank
Limescale deposits may form in the water tank. To ensure correct
function of your IMPRESSA, you should descale the water tank from
time to time.
TT Remove the water tank.
TT If you use a CLEARYL filter cartridge, remove this.
TT Descale the tank with a mild, commercially available descaling agent in accordance with the instructions of the manufacturer.
TT Rinse the water tank with clean water afterwards.
TT If you use a CLEARYL filter cartridge, insert this again.
TT Fill the water tank with fresh, cold water and reinsert.
51
7 Display messages
7 Display messages
Message
Cause/Result
Action
FILL WATER TANK
The water tank is empty.
You cannot prepare any coffee
products, hot water or milk
products.
TT Fill the water tank (see
Chapter 2, ‘Preparing and using
for the first time – Filling the
water tank’).
EMPTY GROUNDS
The coffee grounds container
is full. You cannot prepare any
coffee products, but you can
prepare hot water or milk.
TT Empty the coffee grounds
container and the drip tray.
EMPTY TRAY
The drip tray is full. You cannot TT Empty the drip tray.
prepare any coffee products,
hot water or milk products.
TRAY MISSING
The drip tray is not inserted
correctly or is not inserted at
all. You cannot prepare any
coffee products, hot water or
milk products.
TT Insert the drip tray.
TT Clean the metal contacts on
the back of the drip tray.
FILL BEANS
The bean container is empty.
You cannot prepare any coffee
products, but you can prepare
hot water or milk.
TT Fill the bean container (see
Chapter 2, ‘Preparing and using
for the first time – Filling the
bean container’).
PRESS RINSE
The IMPRESSA is prompting
you to start a rinse operation
or continue a started maintenance program.
TT Press the maintenance button
to start rinsing or to continue the
maintenance program.
COFFEE READY /
RINSE CAPPUCCINO
The IMPRESSA is prompting
you to start cappuccino
rinsing.
TT Press the maintenance button
to start cappuccino rinsing.
COFFEE READY /
CLEAN MACHINE
After 220 preparations or
80 switch-on rinses, the
IMPRESSA will prompt you to
clean it.
TT Clean the machine (see
Chapter 6, ‘Maintenance –
Cleaning the machine’).
52
7 Display messages
Message
Cause/Result
Action
COFFEE READY /
CLEAN NOW
After 250 preparations the
IMPRESSA will prompt you
to clean it.
TT Clean the machine (see
Chapter 6, ‘Maintenance –
Cleaning the machine’).
COFFEE READY /
The IMPRESSA is prompting
DECALCIFY MACHINE you to descale it.
TT Descale the machine (see
Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY /
DECALCIFY NOW
The IMPRESSA is prompting
you to descale it.
TT Descale the machine (see
Chapter 6, ‘Maintenance –
Descaling the machine’).
COFFEE READY /
CHANGE FILTER
After 2000 oz (60 liters) of
water have flowed through, or
after two months, the filter will
cease to work.
TT Replace the CLEARYL filter
cartridge (see Chapter 6
‘Maintenance – Changing the
filter’).
COFFEE READY /
CHANGE NOW
After 2200 oz (65 liters) of
water have flowed through,
the filter will cease to work.
TT Replace the CLEARYL filter
cartridge (see Chapter 6
‘Maintenance – Changing the
filter’).
NOT ENOUGH
PRE-GROUND
TT The next time you make coffee
There is too little pre-ground
use more pre-ground coffee
coffee in the filler funnel. The
IMPRESSA stops the operation. (refer to Chapter 4, ‘Preparation
at the touch of a button –
Pre-ground coffee’).
53
8 Troubleshooting
8Troubleshooting
Problem
Cause/Result
Action
Grinder is making a very
loud noise.
There are foreign objects
in the grinder.
TT Contact Customer Support in your
country (see ‘JURA contact details /
Legal information’).
The frother does not
produce enough milk foam
or milk sprays from the
cappuccino frother.
The cappuccino frother
is dirty or incorrectly
attached.
TT Rinse and clean the cappuccino
frother (see Chapter 6, ‘Maintenance –
Cappuccino frother‘).
TT Assemble the cappuccino frother
correctly and firmly attach the frother
to the Connector System© (refer to
Chapter 6 ‘Maintenance – Disassembling and rinsing the frother’).
Coffee only comes out
in drips when it is being
prepared.
Coffee or pre-ground
coffee has been ground
too finely and is blocking
the system.
TT Put the grinder on a coarser setting
or use coarser pre-ground coffee (refer
to Chapter 2, ‘Preparing and using for
the first time – Adjusting grinder’).
Water hardness cannot
be adjusted.
The CLEARYL filter
cartridge is activated.
TT Deactivate the CLEARYL filter
cartridge in programming mode.
COFFEE READY /
FILL BEANS
The grinder is not yet
completely filled with
beans.
TT Prepare a coffee specialty.
The bean monitor is
dirty.
TT Clean the bean container
(see Chapter 6, ‘Maintenance –
Cleaning the bean container’).
is displayed although
the bean container has
been filled.
COFFEE READY /
FILL BEANS is not
displayed although the
bean container is empty.
EMPTY TRAY
is always displayed.
FILL WATER TANK
is displayed although
the water tank is full.
54
The metal contacts of the TT Clean and dry the metal contacts
drip tray are dirty or wet. on the back of the drip tray.
The water tank float is
trapped.
TT Descale the water tank (see
Chapter 6, ‘Maintenance – Descaling
the water tank’).
8 Troubleshooting
Problem
Cause/Result
Action
ERROR 2 is displayed.
If the machine was
exposed to the cold for a
long period of time, it is
disabled from heating up
due to safety reasons.
TT Warm up the machine at room
temperature.
Other ERROR messages
are displayed.
–
TT Turn the IMPRESSA off at the power
switch. Contact Customer Support in
your country (see ‘JURA contact
details / Legal information’).
EE If you have not been able to solve the problem, contact Customer Support in your country (see ‘JURA contact details /
Legal information’ ).
55
9 Transport and environmentally neutral disposal
9 Transport and environmentally neutral disposal
Transport / Emptying
the system
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transportation.
In order to protect the IMPRESSA from frost during transportation,
the system must be emptied.
Precondition: The IMPRESSA is switched off (standby).
TT Remove the water tank.
TT Place a receptacle under the hot water spout and another
under the frother.
cTPress the maintenance button until SYSTEM
EMPTYING appears.
A small amount of water flows from the frother and the
hot water spout. The operation stops automatically. The
­IMPRESSA will switch itself off.
3TTurn your IMPRESSA off at the power switch.
EE The next time you use the machine the system must be
­refilled (see Chapter 2, ‘Preparing and using for the first
time – First-time use’).
Disposal
56
Please dispose of old machines in an environmentally neutral way.
H
10 Technical data
10 Technical data
Voltage
120 V ~, 60 Hz
Power
1250 W
Safety test
Energy SAVE NO
23 Wh
Energy SAVE LEVEL 1
16 Wh
Energy SAVE LEVEL 2
14 Wh
Energy consumption in standby 5.6 Wh
mode
Directives
Pump pressure
Static max. 15 bar
Holding capacity of water tank
96 oz (2.8 l)
Holding capacity of bean
container
10 oz (280 g)
Holding capacity of coffee
grounds container
Approx. 20 servings
Cord length
Approx. 43.3 in. (Approx. 1.1 m)
Weight
29.3 lb (13.3 kg)
Dimensions (W x H x D)
16.2 x 18.5 x 15.4 in.
(41 x 47 x 39cm)
The machine complies with the following directives:
ZZ Standard UL 1082
ZZ Canadian Standard CSA C22.2 No. 64
57
Index
Index
A
B
C
Entering a default setting for the amount of
water for a cup size 21
Errors
Addresses 60
Aroma preservation cover 8
Automatic switch-off 36
Bean container
Aroma preservation cover 8
Cleaning 51
Cover 8
Filling 12
Troubleshooting 54
F
Filter
Cappuccino 27
Cappuccino frother
Changing 41
Using and activating 14
Fineness of grind
Adjusting grinder 17
Fineness of grind switch 8
Cleaning
Bean container 51
Cappuccino frother 49
Machine 43
CLEARYL filter cartridge
H
Changing 41
Using and activating 14
Coffee 26
Coffee à la carte 26
Coffee grounds container 8
Coffee spout, height-adjustable 8
Contact details 60
Control options 19
Cover
Bean container 8
Filler funnel for pre-ground coffee 8
Default settings in programming mode 31
Descaling
Display messages 52
Display, Messages 52
Drip tray 8
Emptying the system 56
Energy-saving mode 33
58
Fineness of grind switch 8
First-time use 13
Hardness of water 16
Hotline 60
Hot milk 29
Hot water 30
Hot water portion 30
I
Hot water spout 8
Important safeguards
Safety 4
J
Customer support 60
Machine 45
Water tank 51
E
Filler funnel for pre-ground coffee 8
Filling
Bean container 12
Water tank 12
Cleaning 49
Rinsing 48
D
Espresso 25
L
Internet 11
JURA
Contact details 60
Language 39
Latte macchiato 27
M
Machine
Cleaning 43
Descaling 45
Rinsing 41
Setting up 12
Switching off (stand-by) 18
Switching on 17
Index
Maintenance 40
Maintenance tips 40
S
Milk
Safety
Important safeguards 4
Hot 29
Milk portion 29
Selector switch 9
Settings
Milk foam 29
Default settings in programming mode 31
Entering a default setting for the amount of
water for a cup size 21
One-off settings before and during preparation 20
O
P
One-off settings before and during preparation 20
Setting up 12
Standby
Power switch 8
Pre-ground coffee 28
Switching off 18
Filler funnel 8
Pre-ground coffee 28
Preparation
At the touch of a button 25
Cappuccino 27
Coffee 26
Coffee à la carte 26
Espresso 25
Hot water 30
Latte macchiato 27
Milk 29
Pre-ground coffee 28
Problems
Troubleshooting 54
Professional Cappuccino Frother 8
Disassembling and rinsing 50
Programmable switch-on and switch-off time
35
Programming mode 31
R
Automatic switch-off 36
Energy-saving mode 33
Language 39
Products 31
Rinses 37
Switch-on and switch-off time 35
Time and weekday 34
Unit amount of water/Time format 38
T
U
V
Switching off (stand-by) 18
Switching on 17
Symbol description 3
Technical data 57
Telephone 60
Time and weekday 34
Troubleshooting 54
Use, First time 13
Viewing information and maintenance status
24
Viewing maintenance status 24
W
Water hardness 16
Determining and adjusting 16
Water tank 8
Descaling 51
Filling 12
Works settings 33
Rinses 37
Rinsing
Cappuccino frother 48
Machine 41
Rotary Switch 9
59