TM
COMMERCIAL
2-SPEED BLENDER
Operating Instruction Manual
XLB-44
Model
Voltage
Power
Volume
Amperage
XLB-44
120V ~ 60Hz
400W
44 oz
3.5A
Overall Height
15-1/4"
Base Dimensions
Width Depth Height
6.5"
8"
7"
BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS
Congratulations on your purchase of this ACCELMIX TM commercial blender. When used as intended, and with proper
care and maintenance, you are sure to experience years of reliable operation from this equipment. To ensure best
results, it is important that you read and follow the instructions in this manual carefully. It is important to keep
these instructions in a safe place for future reference.
TM
Commercial 2-Speed Blender
Important For Future Reference
Please complete the following information and retain this manual for the life of the product. This
information is required for Warranty Service and/or parts. Please see Page 10 for more information
on your Warranty and How to Register.
XLB-44
Model Number
!
!
!
XLB
Serial Number
Date Purchased
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause
property damage, injury, or death. Read the
installation, operation, and maintenance
instructions thoroughly before installing
or servicing this equipment.
AVERTISSEMENT: Toute installation, réglage,
modification, réparation ou entretien
incorrect peut occasionner des dommages
matériels, des blessures graves ou la mort.
Lire les intructions d'installation, d'utilisation et
d'entretien attentivement avant d'installer ou de
réparer cet appareil.
CAUTION: These models are designed, built, and
sold for commercial use only. If these models
are positioned so the general public can use
the equipment, make sure that caution signs,
warnings, and operating instructions are
clearly posted near each unit so that anyone
using the equipment will use it correctly and
not injure themselves or harm the equipment.
ATTENTION: Ces modèles sont conçus, fabriqués,
et vendus pour un usage commercial seulement.
Si ces modèles sont placés pour que le grand
public puisse les utiliser, assurez-vous que les consignes
d’attention, d'avertissement, et les instructions
d'utilisation soient clairement affichées près de
chaque unité de sorte que n'importe quel utilisateur de
l'appareil l'emploie correctement et ne se blesse pas ou
n'endommage pas l'appareil.
WARNING: A factory authorized service
provider should handle all maintenance
and repair. Before doing any maintenance
or repair, follow service set up
arrangement on page 10.
AVERTISSEMENT: Un technicien autorisé par
l'usine devra effectuer tout l'entretien et les
réparations. Avant de faire tout entretien ou
réparation, veuillez contacter WINCO.
!
!
!
Introduction
Congratulations on the purchase of your ACCELMIXTM machine. Please take the time to carefully read through this manual to ensure the machine is
operated and maintained properly, to ensure the best possible performance from this product for many years.
WINCO will not accept liability if:
• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the machine.
• Non-original spare parts are used.
• The machine has not been handled and cleaned correctly.
• There is any use damage to the unit.
2
TM
Commercial 2-Speed Blender
Table of Contents
Specifications........................................................................................ 1
Warnings ............................................................................................... 2
Introduction ......................................................................................... 2
Table of Contents ................................................................................ 3
Packaging ............................................................................................. 3
Important Safeguards......................................................................... 4
Operation ............................................................................................. 6
Cleaning, Care & Maintenance .......................................................... 6
Safety & Troubleshooting .................................................................. 7
Exploded View ..................................................................................... 8
Parts List ............................................................................................... 9
Limited Warranty .............................................................................. 10
Package Contents
Unpacking the Equipment
All units come with an Operating Instruction Manual
and the following:
• XLB-44 Commercial Blender Base
• 44 oz. Blender Container & Lid
Dispose of all packaging materials in an
environmentally responsible manner.
1. Remove all packing materials and tape, as well as any protective
plastic and cardboard from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.
Save the original box and packaging for use in
packaging and shipping the equipment if services
are needed.
WINCO® prides itself on quality and service, ensuring that at the
time of packing, all products are supplied fully functional and free
of damage. Should you find any damage as result of freight, please
contact your WINCO® dealer immediately.
Function and Purpose
This unit is intended to be used in commercial food-service operations only. It is not intended for household, industrial or laboratory use.
NOTE
Please remember that this manual and the warning labels do not replace the need to be alert, to properly train
and supervise operators, and to use common sense when using this equipment.
3
TM
Important Safeguards
To ensure safe installation and operation, please carefully read and understand the following statements.
Unless the operator is adequately trained and supervised there is a possibility of serious injury. Owners of
this equipment bear the responsibility to make certain that this equipment is used properly and safely, and to
strictly follow all of the instructions contained in this manual and the requirements of local, state or federal
law.
Owners should not permit anyone to touch this equipment unless they are over 18 years old, are adequately
trained and supervised, and have read and understood this manual.
Owners should also ensure that no customers, visitors or other unauthorized personnel come in contact with
this equipment. It is the responsibility of the owner and the operator to remain alert to any hazards posed by
the function of this equipment.
If there is ever uncertainty about a particular task or the proper method of operating this equipment, ask an
experienced supervisor.
Safety Warnings
This manual contains a number of precautions to follow to help promote safe use of this equipment.
FOR YOUR SAFETY
ESURE DE SECURITE
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Ne pas entreposer ni utiliser de'essence ni autres vapeurs ou liquides
inflammables a proximte de cet appareil ou de tout autre apparel!
WARNING
AVERTISSEMENT
Improper installation, adjustment, alteration, service or
maintenance can cause property damage, injury or death.
Read these installation, operating and maintenance instructions
thoroughly before installing or servicing this equipment.
4
Linstallation, le reglage, la modification, la reparation ou
I'entretien incorrect de cet appareil peut causer des dommages
materiels, des blessures ou la mort. Lire attentivement les
instructions d'installation, de fonctionnement et d'entretien avant
de proceder a son installation ou entretien.
TM
Warning
Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Read the installation,
operation, and maintenance instructions thoroughly before installing or servicing this equipment.
Caution Before Using Appliance
1. Read all instructions carefully. Do not use this appliance for
anything other than its intended use.
2. Unplug from outlet when not in use, prior to installing or
removing parts, and before cleaning. Allow for the device
blades/gear to stop rotating.
3. To protect against the risk of electrical shock, do not immerse
the appliance, cord or plug in water or other liquids.
WARNING
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modified.
4.
5.
6.
7.
AVERTISSEMENT
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modifié.
Do not use an adapter.
Do not use an extension cord.
Do not remove ground.
Do not operate this device or any other electrical equipment
with a damaged cord or plug, or after the unit malfunctions, or
is dropped or damaged in any manner. Return to the nearest
WINCO® Authorized Service Center for examination, repair, and /
or adjustment.
8. The use of accessory attachments not recommended by WINCO
may cause fire, electric shock or injury.
9. Not intended for outdoor installation.
10.Do not let the cord hang over the edge of a table or counter, or
touch hot surfaces.
WARNING
AVERTISSEMENT
Fire Hazard.
Risque d'incendie
Correct installation precautions,
procedures and regulations
must be followed. Operation
and safety training is necessary
for all users of this equipment.
La surchauffe des vapeurs d'huile ou de
l'huile peut s'enflammer et provoquer
un incendie. Surveillez la température,
la qualité et le niveau d’huile. Utilisez et
entretenez le système d'élimination des
vapeurs d'huile.
11.Do not place on or near a heat source.
12.Do not overload the unit.
13.This appliance should always be on a stable and steady
countertop or table.
14.This appliance is not intended for use by individuals (including
children) with reduced or impaired physical, sensory, or mental
capabilities, or lack of experience or knowledge, unless they have
been given proper supervision or instruction concerning the use
of this appliance by a person responsible for their safety.
15.Children should be supervised at all times to avoid injuring
themselves or damaging the appliance in any way.
16.Always place cover on container while blending.
17.AVOID CONTACT WITH MOVING PARTS.
18.Do not put hands, spoons or any other utensils into blender
container while the unit is on as doing so could cause serious
injury and/or damage to the blender.
19.Do not try to override the safety switch on the blender base for
the blender container. This may damage the switch and cause
injury.
20.Do not try to stop the center rotating gear on the blender base
or prevent it from spinning. This may cause damage to the unit
and/or injury.
5
TM
Operation
1.
2.
3.
4.
5.
6.
7.
8.
Make sure toggle switch is in off / 0 position.
Plug-in power cord [attached to the base] into an electrical outlet.
Secure the container on top of base.
Add ingredients as desired.
Cover top of container with the included lid.
Turn on and increase speed to achieve desired consistency.
DO NOT ALLOW FOREIGN OBJECTS TO COME INTO CONTACT WITH THE BLADE WHILE IT IS ON AND ROTATING.
When blending is completed, turn off and allow blade to come to a complete stop before removing container.
Caution
DO NOT allow any object other than food come into contact with the blade while it is on and rotating. This will cause contamination of
ingredients, damage to the blades/motor and possible injury.
The blender has a safety which will prevent it from spinning unless the container is properly secured to the base. Removing the
container will automatically stop the unit. However, doing this is not recommended due to possible damage to the gears between the
base and container.
Cleaning & Maintenance
Before using this equipment it must be cleaned and dried thoroughly. Clean all surfaces before use. Failure to
clean surfaces before using the unit could cause food contamination.
•
•
•
•
•
•
Half fill the jug with warm water and add a few drops of dish soap.
Attach the lid and lid plug.
Switch the machine on low and run for 60 seconds.
Turn off, remove jug, rinse and dry with a soft cloth.
The power base can be wiped off with a damp cloth.
Do not immerse the device completely in water to clean. The appliance should also NOT be cleaned with a water jet.
Warning: do not allow excess liquid to drip into ventilation openings as this may affect the electrical and
mechanical systems.
NOTE:
Proper cleaning instructions must be followed; otherwise, operation of the unit may be seriously impaired. Do not
wash parts in an automatic dishwasher.
WINCO® authorized service personnel must perform any other servicing.
6
TM
Safety
Service and Repair
A WINCO® Approved Service Technician should carry out repairs if
necessary. Do not remove any components or service panels on this
product.
If the power cord is damaged, it must be replaced by a WINCO®
Approved Service Technician in order to avoid a hazard.
There are no user-serviceable parts within this appliance.
To avoid serious injury or damage, never attempt to repair the unit
yourself.
To initiate warranty service contact: support@wincous.com
or call: 973-295-3899.
DO NOT send unit to WINCO® without first contacting our customer
service department.
See "Limited Warranty" section on page 10 for details.
Troubleshooting
If your ACCELMIXTM blender does not operate, please check the following prior to placing a service call.
PROBLEM
The unit is not turning on
POSSIBLE CAUSE
RECOMMENDED SOLUTION
Power supply
Check that the power supply cord is correctly
plugged in and outlet is working.
Breaker has blown
Reset breaker button on the rear base of the unit.
Container is not sitting on base properly
Make sure container is secured to the base
correctly.
Power switch has not been turned on
Check that the unit is plugged in and turned on.
Plug/cord or external wiring is damaged
Internal wiring fault
The unit is vibrating too much
Call WINCO to make service arrangements through
their service provider network.
Unit is not on stable surface
Place the unit on a level surface or on top of a
vibration resistant surface such as a rubber mat.
Lid is not on properly
Adjust the lid so that if fits tightly and is centered
on the container.
Loose hardware
Tighten any loose screws, nuts or bolts.
7
TM
Exploded View
Model XLB-44
1
2
3
4
5
6
7
8
9
8
TM
Parts List
Model XLB-44
No.
PARTS
QTY
Item#
1
Filler Cap
1
XLB44-P1
2
Container Cover
1
XLB44-P2
3
Container
1
XLB44-P3
4
Gasket
1
XLB44-P4
5
Cutter Assembly
1
XLB44-P5
6
Collar
1
XLB44-P6
7
Clutch
1
XLB44-P7
8
Switch Assembly
1
XLB44-P8
9
Suction Feet
4
XLB44-P9
1-6
Container set (Group 1-6)
1
XLB44-P10
9
TM
Limited Warranty
WINCO® warrants to the original purchaser of new equipment that said equipment, when installed in accordance with our instructions within
North America and subjected to normal use, is free from defects in material or workmanship for a period of 1 year. The labor warranty is one year
from original installation or 18 months from actual factory shipment date, whichever date occurs first.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED. WINCO EXPRESSLY DISCLAIMS ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR EXPRESSED OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WINCO’S OBLIGATION AND LIABILITY UNDER THIS WARRANTY IS EXPRESSLY LIMITED TO REPAIRING AND REPLACING EQUIPMENT
THAT PROVES TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP WITHIN THE APPLICABLE WARRANTY PERIOD.
IN NO EVENT SHALL WINCO BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES TO BUYER OR ANY THIRD PARTY,
INCLUDING, WITHOUT LIMITATION, LOSS OF PROPERTY, PERSONAL INJURY, LOSS OF BUSINESS OR PROFITS OR OTHER ECONOMIC
LOSSES, OR STATUTORY OR EXEMPLARY DAMAGES, WHETHER IN NEGLIGENCE, WARRANTY, STRICT LIABILITY, OR OTHERWISE.
This warranty is given only to the first purchaser from a retail dealer. No warranty is given to subsequent transferees.
Warranty does not cover product failures caused by: failure to maintain, neglect, abuse, damage due to excess water, fire, normal wear, improper
set up and use. Periodic maintenance is not covered.
This warranty is not in force until such time as a properly completed and digitally signed Installation/Warranty Registration has been received by
WINCO within 30 days from the date of installation.
Warranty Service
To initiate warranty service contact: support@wincous.com
or call: 973-295-3899
DO NOT send unit to WINCO® without first contacting our customer service department.
Register online at:
http://support.wincous.com
Proof of purchase is required to extend warranty more than 1 year from date of shipment from the factory.
10
TM
Limited Warranty
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE STATEMENT BETWEEN THE BUYER AND SELLER. WINCO®
NEITHER ASSUMES NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH
SAID EQUIPMENT.
Examples of items not covered under warranty, but not limited to just these items:
1. Acts of God, fire, water damage, burglary, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after-market parts.
5. Repairs made by anyone other than a WINCO® designated service provider.
6. Lubrication.
7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
8. Cleaning of equipment.
9. Misuse or abuse.
WARRANTY REGISTRATION
SCAN THE QR CODE WITH YOUR MOBILE DEVICE
or go to
http://support.wincous.com
TO FILL OUT AND SUBMIT YOUR WARRANTY REGISTRATION.
Please keep this manual in a safe place for future use!
11
TM
Model: XLB-44
www.wincous.com