Central Home Heating and Hot Water Supply Next Generation Central Home Heating and Hot Water Combined Ecodan – Next Generation Central Heating and Hot Water Heating Combined Increasing energy bills, coupled with the need to heat our homes and hot water efficiently, is driving the demand for alternative forms of domestic heating. Mitsubishi Electric has utilised their expertise and industry-leading technology to develop Ecodan – a super energy efficient heat pump solution that combines both hot water heating and room heating through one system. On average, hot water and home heating needs combined account for over 70%*1 of the overall energy bill in New Zealand homes. Domestic heating is therefore an obvious area to target in reducing energy bills. This is especially pertinent during the winter months, where a combination of taking longer, hotter showers and the increased need for a warm and dry home, typically drives up power bills. An Ecodan Heat Pump System can help reduce your heating and hot water bill when compared to gas and direct electric systems. What is Ecodan? Ecodan is an advanced heat pump system that cleverly combines the hot water heating supply for a home with energy efficient whole home central heating; all through the same system. COP Comparison Chart Ecodan Electric Heating Gas Heating (Non-Condensing) 0.82 0.99 3.20 Heat pumps use electrical energy and take low grade heat energy from the outdoor air, to heat refrigerant which in turn heats water for domestic use and space heating. The efficiency of a heat pump is known as the Coefficient of Performance or COP. This is a ratio of the heat delivered to power consumed. For every 1kW of electrical input energy, Ecodan absorbs renewable heat energy from the outdoor air to provide the home with an average of at least 3.2kW*2 of heat output. Compared to typical gas and direct electric heating systems that can 2 have higher running costs with COPs as low as 0.82*3, Ecodan provides an energy efficient alternative. Electrical energy input 1kW 2.2kW Low temperature renewable heat energy taken from the environment 3.2kW Heat energy output As independently tested by BSRIA based upon BSEN14511 Part 3 standard rating conditions. Due to the method of operation, the performance of heat pumps will vary based upon the temperature of the heat source and the requirements of the heat delivered. The BSEN14511 testing relates to the heat pump performance only and not the entire heating system. Return on Investment The estimated return on investment of an Ecodan System, when compared to a gas or direct electric heating system, is about 10 years*4. There are ways of reducing this payback period further, such as taking advantage of lower cost nightly electricity tariffs available; reducing homeowners’ energy bills by heating the hot water cylinder during the night. Large households with high hot water usage could bring the payback period down significantly, closer to 5 years*4. • Savings could be as much as 35% when compared to traditional gas central heating systems. • Savings could be as much as 40% when compared to traditional direct electric heaters. *1 Based on data sourced from NZGBC. *2 The overall system efficiency and energy savings will depend on the comparison with your current heating system, satisfactory system design and installation, and operational settings i.e. how you use the heating system. *3 Based on manufacturer information for gas instant hot water heater (non-condensing). *4 Payback period comparison based on average energy supplier costs per kWh over an average winter heating period. Actual savings may vary in line with gas and electricity price fluctuations and seasonal conditions. This is an estimate only. Fast Heat Up Times! • Fast water heating times from 15°C – 55°C in 1 hour for a 3 bedroom house*1 • Less than 30 minutes to re-heat half the tank (100 litres)*1 • Even faster heat up times with Zubadan Technology*2 *1 When using PUHZ-W112VHA, ambient temperature above 2°C. *2 Zubadan only available on specific models – see specification tables. Ecodan Central Heating with Domestic Hot Water Systems Ecodan is a highly energy efficient hot water heat pump system comprised of an outdoor hot water heat pump and an indoor component – a Hydrobox or a Cylinder Tank. A reliable total home heating solution using radiators and/or underfloor heating in conjunction with hot water supply provides year-round comfort with advanced control. With proven Mitsubishi Electric technology, Ecodan is designed for New Zealand conditions; maintaining high performance during the winter months when heating is in high demand. Packaged Cylinder System Whether you need central whole home heating, hot water or both, Ecodan Hydrobox and Cylinder Systems can provide the perfect solution. Hot Water Both the Hydrobox and Cylinder are compatible with the Monobloc and Split Type Ecodan Outdoor Units ranging from 4.5–14 kW of heating and hot water for your home or light commercial application. Packaged Cylinder System The 200 litre Cylinder provides improved performance and fast heat up times through the use of Plate Heat Exchanger Technology and FTC5 Control. The Cylinders are completely pre-plumbed and wired for ease of installation. The Cylinder can provide heating and hot water to your home. UFH* Outdoor Monobloc/Split PUHZ Radiator Indoor Cylinder Packaged Hydrobox System 3-Way Valve Packaged Hydrobox System The Hydrobox is primarily used for space heating in the form of underfloor and/or radiators. With a small footprint that is sized similarly to Combi Boilers, the Hydrobox provides a highly adaptable solution for retrofit and new builds. Whether connecting the Monobloc or Split Unit only, 2 pipes are connected to supply the unit just like the Cylinder. For systems where a third party tank is to be installed, a 3-way valve can be added to the system and connected to the FTC5 Controller. UFH* Radiator Indoor Hydrobox Outdoor Monobloc/Split PUHZ Indoor 3rd Party Cylinder Hot Water *UFH: Under Floor Heating 4 Ecodan for Pool and Spa Applications Ecodan Hot Water Heat Pumps provide highly efficient hot water to pools and spas. Comprising of a durable outdoor hot water heat pump, specialised heat exchanger, flow switch and advanced controller, Ecodan is the ideal and cost efficient way to heat your pool or spa all year round. Spa Pools Spa pools consume more power than many swimming pools due to higher temperatures and potential heat losses. Installing a hot water heat pump to an existing spa pool can significantly reduce your heating costs. Power consumption can be reduced by 3 to 4 times. Swimming Pools Most swimming pools are used during the summer months and remain unused for the rest of the year. Installing a hot water heat pump can enable you to enjoy your swimming pool year-round! A range of titanium coil / PVC shell heat exchangers are matched to the PUHZ hot water heat pump units. This removes any risk of corrosion-related damage due to salt or chlorine water treatment and simplifies pool water pipe work. Packaged Heat Exchanger System Outdoor Split PUHZ Heat Exchanger Pool / Spa Ecodan Technology, Smart Energy Monitoring and System Management State of the art energy monitoring and management of the Ecodan Heat Pump System means families now have the visibility and freedom to efficiently manage their overall household power consumption for heating and hot water. Energy monitoring ensures households can take advantage of off-peak tariffs, providing them the ability to save even more on their power bill. Smart Energy Monitoring Other Features View electricity consumption and heat output on the remote controller. End-users can now easily check the energy data of the Ecodan Heat Pump. • Daily, monthly and yearly data are stored and can be displayed using the main remote controller Data Shown on the Remote Controller: • Consumed electrical energy for space heating, cooling and domestic hot water (kWh) • Delivered energy for space heating, cooling and domestic hot water (kWh) • External power meter and heat meter can be connected for accurate measurement • An SD card is included for storing usage data Heating capacity produced Electric energy used 2-Zone Control allows you to simultaneously control two different temperature zones. Optional PAC-TZ01-E 2-Zone Kit Using Ecodan, it is possible to control two different flow temperatures, thereby managing two different heating load requirements. • Compact: fits on top of Cylinder or wall mountable with Hydrobox. The system can adjust and maintain two flow temperatures when different temperatures are required for different rooms; for example, controlling a flow temperature of 45°C for the bedroom radiators and another flow temperature of 35°C for the living room underfloor heating. • Easy installation: G1 screw type flexi piping connections. • All in one kit: Key functional components are incorporated. 2 Zone Control System* Wireless Remote Controller as Thermistor 40°C Hydro Box Pump FTC Mixing Control Flow Switch Radiator Mixing Valve Pump Mixing Tank/Header 30°C Flow Switch Underfloor Heating * Items such as a Mixing Tank, Mixing Valve, Flow Switch and Pumps are not included and need to be purchased locally. Or use the optional PAC-TZ01-E 2-Zone Kit. 6 Auto Adaptation Our advanced Auto Adaptation Function measures the room temperature and outdoor temperature, calculating the required heating capacity for the room. The flow temperature is automatically controlled according to the required heating capacity, while optimal room temperature is maintained at all times; ensuring the appropriate heating capacity and preventing energy wastage. Future Room Temperature Estimation Room Temperature Target Temperature Higher than Target Temperature Lower the flow temperature Approximately same as Target Temperature Keep the flow temperature Lower than Target Temperature Raise the flow temperature Modify the flow temperature by comparing actual and estimated room temperature 3 points T0 T1 Current Future Time By estimating future changes in room temperature, the system works to unnecessary increases and decreases in the flow temperature. Auto ] [prevent Example Adaptation maximises both comfort and energy savings. a) Outdoor temperature is gradually decreasing… 0 -5 -10°C -10 -6°C Plate Heat Exchanger and Patented Scale Trap Technology* 7:00 7:00 6:00 5:00 4:00 3:00 2:00 1:00 0:00 25 Ecodan can use a Plate Heat Exchanger to heat tap water, resulting in much higher domestic hot water performance. 36.6°C 30.0°C at A-10 8:00 6:00 5:00 4:00 3:00 2:00 1:00 0:00 The Aluminium Plate Heat Exchanger and patented Scale Trap Technology help achieve greater efficiencies. In conventional systems, there is a risk of b) Target flow temperature calcium scale building up on the Plate Heat Exchanger if it is exposed to tap Target flow temp. is Target flow temp. goes up 40 water directly; therefore making difficult to following heat tap To resolve this graduallyitlowered. the water. heat curve. problem, Ecodan is equipped with a “Scale Trap” that catches calcium nuclei 35 in the tap water before it has a chance to grow into large scales, thereby 34.6°C 30 inhibiting at A-6 build-up in the External Heat Exchanger. 8:00 -15 In case of specialflow localised conditions as veryeven hard when tap water, please Bythe Auto Adaptation, temperature can such be lowered outdoor temp. is decreasing. consult a specialist before installation. c) Room temperature Repeats Thermo ON/OFF Room temp. can be kept stable The Secret Behind Our External Plate Heat Exchanger System 23 and room temp. becomes unstable. and stays at the targeted level at the end. Actual with Auto Adaptation By Auto Adaptation, flow temperature can be lowered without sacrificing comfort. Pump Actual outdoor temperature with Heat Curve estimation with Auto Adaptation Target room temperature Scale Trap Fresh Water P - HEX External P-HEX Circuit DHW Storage Tanks * Only available on Mitsubishi Electric made cylinders. 8:00 7:00 Hot Water 6:00 5:00 3:00 2:00 Tap Water 19 1:00 Circulating Water 0:00 21 20 4:00 22 Zubadan – Reliable Performance in Low Temperature Outdoor Conditions New Generation Zubadan* provides powerful heating in cold regions where most heat pumps’ performance lacks. Zubadan’s rated heating capacity is maintained even in outdoor temperatures as low as –15°C, guaranteeing total home comfort when you need it most. Zubadan Inverter Technology Flash Injection Technology New Generation Zubadan Inverter Technology* provides powerful heating in cold regions where heat pump performance can diminish. With Zubadan, rated heating capacity is maintained even in outdoor temperatures as low as -15°C, with guaranteed heating operation at -25°C. Zubadan guarantees a warm, comfortable home when you need it most. Furthermore, Zubadan can provide even faster tank heat up times in low ambient temperatures compared to standard models. The Flash Injection Circuit is an original Mitsubishi Electric technology. A heat exchange process at the Heat Interchanger transforms liquid refrigerant into a two-phase, gas-liquid state and then compresses the gas-liquid refrigerant at the Injection Compressor. This circuit secures a sufficient flow rate of refrigerant for heating when outdoor temperatures are very low. Thanks to an improved Heat Interchanger and the introduction of a new Injection Compressor, the Flash Injection Circuit is now more powerful then ever. Flash Injection Circuit Heat Interchanger (HIC) Injection Compressor Benefits of Zubadan New Generation Integrated Capacity (kW) Approximately 22% Higher than our previous model 15 14 13 12 11 10 9 Nominal capacity can be kept at -15°C ! ZUBADAN New Generation Previous model -20°C -15°C -7°C Outdoor-Air Temperature at Intake Duct Example: PUHZ-SHW140YHA W45 (according to EN 14511) * Zubadan only available on specific models – see specification tables pg 9 and 11. 8 -28°C 0°C Technical Specifications Ecodan Monobloc Air Source Heat Pumps PUHZ-(H)W OUTDOOR UNITS Our range of Ecodan Monobloc Air Source Heat Pumps are available in 5, 8.5, 11.2 and 14kW capacities. Designed to suit a wide range of applications, these models offer a viable solution for the varying requirements that domestic and small commercial applications demand. Key Features • Self-contained unit, only requiring water and electric connections • No need for gas supply, flues or ventilation • 5ºC – 60ºC outlet water temperature Commercial Applications • Optional 2-Zone Energy Efficient Space Heating Control • Dental and doctors’ surgeries • Small retail outlets • Public sector and commercial buildings • Energy monitoring as standard Domestic Applications • Single phase power supply with a low starting current • Heating and hot water • The vast majority of NZ homes • Low maintenance and quiet operation • Operates with outside temperatures as low as -25ºC with Zubadan – HW Models PUHZ-W50VHA2(-BS) PUHZ-W85VHA2(-BS) PUHZ-W112VHA(-BS) PUHZ-HW140VHA2(-BS) ZUBADAN OUTDOOR UNIT PUHZ-W50VHA2(-BS) PUHZ-W85VHA2(-BS) PUHZ-W112VHA(-BS) PUHZ-HW140VHA2(-BS) Capacity (kW) 5.00 9.00 11.20 14.00 Power Input (kW) 1.11 2.15 2.51 3.29 COP 4.50 4.18 4.47 4.26 Capacity (kW) 5.00 8.50 11.20 14.00 Power Input (kW) 1.43 2.68 3.35 4.50 COP 3.50 3.17 3.34 3.11 -15 ~ +35°C -20 ~ +35°C -20 ~ +35°C -25 ~ +35°C SOUND PRESSURE LEVEL AT 1M (dBA)*1 46 48 53 53 LOW NOISE MODE (dBA)*1 40 42 46 46 Water Pipe Size 1" BSP Parallel Thread *ISO 228/1-G1B) 1" BSP Parallel Thread *ISO 228/1-G1B 1" BSP Parallel Thread *ISO 228/1-G1B 1" BSP Parallel Thread *ISO 228/1-G1B Flow Rate (l/min) 40.1 HEATING*1 (A7/W35) HEATING*2 (A2/W35) OPERATING AMBIENT TEMPERATURE (°C DB)*4 WATER DATA DIMENSIONS (mm) 14.3 25.8 32.1 Water Pressure Drop (kPa) 12 13.5 6.3 9 Width 950 950 1020 1020 Depth 330+30*3 330+30*3 330+30*3 330+30*3 Height 740 943 1350 1350 64 79 133 134 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz WEIGHT (kg) Electrical Supply ELECTRICAL DATA Phase Single Single Single Single Maximum Current (A) 13 23 29.5 35 Fuse Rating 16 25 32 40 *1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511. *2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C. *3 Grille. *4 Heating maximum ambient temperature ~21°CDB, DHW hot water maximum ambient temperature ~35°CDB. 9 Ecodan Split Air Source Heat Pumps PUHZ-S(H)W OUTDOOR UNITS The Ecodan Split Air Source Heat Pump ranges from 4.5kW to 16kW. Designed to suit a wide range of applications, these models offer a viable solution for the varying requirements that domestic and small commercial applications demand. Key Features • Split unit allowing water connections to be made internally • No need for gas supply, flues or ventilation • Single phase power supply with a low starting current • 2-Zone Energy Efficient Space Heating Control Commercial Applications • Energy monitoring as standard • Dental and doctors’ surgeries Domestic Applications • Public sector and commercial buildings • Heating and hot water • Small retail outlets • The vast majority of NZ homes • Low maintenance and quiet operation • Operates in outside temperatures as low as -28ºC with Zubadan Technology – HW Models SUHZ-SW45VAH OUTDOOR UNIT HEATING*1 (A7/W35) HEATING*2 (A2/W35) SUHZ-SW45VAH PUHZ-SW50VKA(-BS) PUHZ-SW75VHA(-BS) 4.50 5.50 8.00 Power Input (kW) 0.89 1.24 1.82 COP 5.06 4.42 4.40 Capacity (kW) 3.50 5.00 7.50 Power Input (kW) 1.15 1.68 2.21 COP 3.04 2.97 3.40 -15 ~ +35°C -15 ~ +35°C -20 ~ +35°C 51 SOUND PRESSURE LEVEL AT 1M (dBA)*1 - 46 42 42 48 Flow Rate (l/min) 12.9 15.8 22.9 Width 840 809+62*5 950 Depth 330 300 330+30*3 Height 880 630 943 54 43 75 R410A R410A R410A LOW NOISE MODE (dBA)*1 DIMENSIONS (mm) WEIGHT (kg) ELECTRICAL DATA Type Charge (kg) - 10m Pipe Length 1.4 1.4 3.2 Pipe Size - Gas/Liquid (mm (in)) 12.7 (1/2") / 6.35 (1/4") 12.7 (1/2") / 6.35 (1/4") 15.88 (5/8") / 9.52 (3/8") Connection Type ELECTRICAL DATA Flared Flared Flared Max Pipe Length (m) 30 40 40 Min Pipe Length (m) 2 2 2 Max Height Difference (m) 30 30 30 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Single Single Single Maximum Current (A) 12 13 17 Fuse Rating 20 16 25 Electrical Supply Phase *1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511. *2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C. *3 Grille. 10 PUHZ-SW75VHA(-BS) Capacity (kW) OPERATING AMBIENT TEMPERATURE (°C DB)*4 WATER DATA PUHZ-SW50VKA(-BS) *4 Heating maximum ambient temperature ~21°CDB, DHW hot water maximum ambient temperature ~35°CDB. *5 Electrical cover. Flow Temperature Controller FTC2B FLOW TEMPERATURE CONTROLLER The FTC2B has been developed to allow the Ecodan PUHZ Range to interface with third party or BEMS (Building Energy Management System) Controls. A combination of volt free and voltage inputs allow the Ecodan PUHZ Range to be used in applications where only simple on/off and temperature control is required. Functions that can be controlled by third party controls: • On/Off Heating Mode • On/Off Heating ECO Mode • On/Off Hot Water Mode • On/Off Holiday Mode • On/Off Legionella Mode • Change Water Flow Temperature Functions that can be monitored by third party controls: • Unit Running PUHZ-SW120VHA(-BS) PUHZ-SHW80/112VHA(-BS) • Error • Defrost The ability to interface with third party controls opens up a huge number of application opportunities. Many processes simply require a heat source that provides hot water, without polished end-user controls. The FTC2B Controller allows the Ecodan PUHZ to be used in these applications. FTC2B inputs and outputs can be used in conjunction with local BEMS. ZUBADAN ZUBADAN PUHZ-SW120VHA(-BS) PUHZ-SHW80VHA(-BS) PUHZ-SHW112VHA(-BS) 16.00 8.00 11.20 3.90 1.72 2.51 4.10 4.65 4.46 12.00 8.00 11.20 3.70 2.25 3.35 3.24 3.55 3.34 -20 ~ +35°C -28 ~ +35°C -28 ~ +35°C 54 51 52 Application Examples 51 49 50 45.9 20.4 32.1 • Smart home integration 950 950 950 330+30*3 330+30*3 330+30*3 1350 1350 1350 118 120 120 R410A R410A R410A 4.6 5.5 5.5 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") 15.88 (5/8") / 9.52 (3/8") Flared Flared Flared 75 75 75 2 2 2 30 30 30 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Single Single Single 29.5 29.5 35 40 32 40 • Leisure centres • Agriculture • Industrial process heating • Under soil heating PAC-IF032B-E FTC2B DIMENSIONS (mm) PAC-IF032B-E Width 69 Height 278 WEIGHT (KG) 2.4 Operating Ambient Temperature (°C DB) ELECTRICAL DATA 336 Depth Electrical Supply Phase 0~+35ºC (RH<80%) Powered from Outdoor Unit (240v) Single 11 FTC5 Packaged Cylinder for Ecodan Monobloc and Split Units FTC5 PACKAGED CYLINDER The Packaged Cylinder offers a highly adaptable heating solution for retrofit or new builds. Designed specifically by Mitsubishi Electric to integrate with the Ecodan Monobloc and Split Air Source Heat Pump Range, the Cylinder provides improved performance and faster heat up times through the use of Plate Heat Exchanger Technology. Fast commissioning via an SD card and energy monitoring functions are included. Key Features • Simple graphical control • Optional 2-Zone Energy Efficient Space Heating Control • Scale Trap Technology • Sleek modern design • Pre-plumbed and wired for faster installation • SD card commissioning • Energy monitoring as standard • Compatible with home automation via Modbus • BMS compatible MelcoBEMS Mini (Modbus) CYLINDER CYLINDER TYPE NOMINAL HOT WATER VOLUME (LITRES) OPERATING AMBIENT TEMPERATURE (°C DB) SOUND PRESSURE LEVEL AT 1M (dBA) Max Flow Rate (l/min) Primary Pump Sanitary Hot Water Pump WATER DATA Connection Size (mm) Heating / DHW Primary Expansion Vessel (Litres) Charge Pressure (MPa (Bar)) Water Circuit WATER SAFETY DEVICES DIMENSIONS (mm) (Optionally Powered by Outdoor Unit) Packaged Split Packaged Split Reversible Packaged Monobloc 200 200 200 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 28 28 28 27.7 27.7 27.7 Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130 Grundfos UPSO 15-60 130 CIL2 Grundfos UPSO 15-60 130 CIL2 Grundfos UPSO 15-60 130 CIL2 28 / 22 28 / 22 28 / 22 12 12 12 0.1 (1) 0.1 (1) 0.1 (1) 1 - 80 1 - 80 1 - 80 0.3 (3) 0.3 (3) Supplied Supplied Supplied 40-70 40-70 40-70 90 / 0.7 (7) 90 / 0.7 (7) 90 / 0.7 (7) Width 595 595 595 Depth 680 680 680 Height 1600 1600 1600 Control Thermistor (°C) Temp and Pressure Relief Valve (°C)/ (MPa (Bar)) 110 / 320 110 / 320 115 / 307 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Single Single Single 10 10 10 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Single Single Single 2 2 2 Max Running Current (A) 9 9 9 Breaker (A) 16 16 16 DHW and 1 Heating Zone*1 DHW and 1 Heating Zone*1 DHW and 1 Heating Zone*1 Electrical Supply Phase Breaker (A) Phase Booster Heater Capacity (kW) MECHANICAL ZONES EHPT20X-VM2C 0.3 (3) Electrical Supply ELECTRICAL DATA ERST20D(C)-VM2CR2 Pressure Relief Valve (MPa (Bar)) WEIGHT EMPTY / FULL (kg) Control Board EHST20D(C)-VM2CR2 Control Thermistor (°C) Flow Sensor (Minimum Flow 5L/min) DHW Cylinder EHST/ERST/EHPT Cylinder Cylinder includes: Flow Temperature Controller (FTC5) with Main Controller and Temperature Sensors, Pumps & Valves for Zone 1 and DHW use, Flow Sensor, Plate Heat Exchanger, Scale Trap, 2kW Booster Heater and Expansion Vessel. *1 Optional 2-Zone Accessory Pack available. 12 FTC5 Packaged Hydrobox for Ecodan Monobloc and Split Units FTC5 PACKAGED HYDROBOX The Hydrobox is primarily used for space heating in the form of underfloor and/or radiators. A small footprint and a similar size to Combi Boilers, they are a highly adaptable solution for retrofit and new builds. Whether connecting the packaged or split unit, only two pipes are connected to supply the unit just like the Cylinder. Hydraulic components are included with FTC5 Control, whilst the split type model features the Heat Exchanger built into the Hydrobox. SD card comissioning and energy monitoring are included. For systems where a third party tank is to be installed, a 3-way valve can be added to the system and connected to the FTC5 Controller. Key Features • Simple graphical control • 2-Zone Energy Efficient Space Heating Control • Sleek modern design • Pre-plumbed and wired for faster installation • SD card commissioning • Energy monitoring as standard • Compatible with home automation via Modbus • BMS compatible MelcoBEMS Mini (Modbus) HYDROBOX CYLINDER TYPE OPERATING AMBIENT TEMPERATURE (°C DB) SOUND PRESSURE LEVEL AT 1M (dBA) Max Flow Rate (l/min) Pump WATER DATA DHW Cylinder DIMENSIONS (mm) (Optionally Powered by Outdoor Unit) ELECTRICAL DATA (Optionally Powered if Required) Packaged Split Packaged Split Reversible Packaged Monobloc 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 0 ~ +35°C (RH<80%) 28 28 28 27.7 27.7 27.7 Grundfos UPM2 15 70 - 130 Grundfos UPM2 15 70 - 130 G1 Nut 28 Primary Expansion Vessel (Litres) 10 10 10 0.1 (1) 0.1 (1) 0.1 (1) Control Thermistor (°C) 1 - 80 1 - 80 1 - 80 Pressure Relief Valve (MPa (Bar)) 0.3 (3) 0.3 (3) 0.3 (3) Supplied Supplied Supplied Booster Heater Control Thermistor (°C) 80 80 80 Booster Heater Manual Reset Thermostat (°C) 90 90 90 Booster Heater Thermal Cut Off (°C) 121 121 121 Width 530 530 530 Depth 360 360 360 Height 800 800 800 44 / 50 45 / 51 37 / 42 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Single Single Single 10 10 10 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz Electrical Supply Phase Breaker (A) Electrical Supply Booster Heater EHPX-VM2C 28 WEIGHT EMPTY / FULL (kg) Control Board ERSD(C)-VM2CR2 Grundfos UPM2 15 70 - 130 Flow Sensor (Minimum Flow 5L/min) WATER SAFETY DEVICES EHSD(C)-VM2CR2 Connection Size (mm) Charge Pressure (MPa (Bar)) Water Circuit EHSD/ERSD/EHPX Hydrobox Phase Single Single Single Capacity (kW) 2 2 2 Max Running Current (A) 9 9 9 Breaker (A) 16 16 16 Hydrobox includes: Flow Temperature Controller (FTC5) with Main Controller and Temperature Sensors, Water Circulation Pump, Flow Sensor, 2kW Booster Heater and Expansion Vessel. 13 Third Party Cylinder via Hydrobox for Ecodan Monobloc and Split Units FTC5 PACKAGED HYDROBOX AND CYLINDER We offer a range of New Zealand made hot water cylinders manufactured to the highest standards, complete with heat exchanger coil designed specifically for Mitsubishi Electric hot water heat pump Hydrobox systems. Cylinders are supplied as standard with all water connections on the front and include standard electric element, thermostat and TPR valve. Sensor pockets are correctly positioned for the cylinder temperature sensor. There are sizes for mains pressure cylinders or buffer tanks and these can be made from 150 to 800 litres. Custom designs are also available. Key Features • Simple graphical control • 2-Zone Energy Efficient Space Heating Control and Hot Water • Sleek modern design • SD card commissioning • Energy monitoring as standard • Compatible with home automation via Modbus • BMS compatible EHSD/ERSD/EHPX Hydrobox FTC5 CONTROLLER – WITH ENERGY MONITORING Mitsubishi Electric’s Fifth Generation Controller (FTC5) includes intelligent room temperature control as standard. This, together with advanced weather compensation, ensures the system delivers efficient, comfortable heating regardless of the season. FTC5 now also includes energy monitoring, showing consumed and produced energy. 14 Ecodan Split Units for Pool and Spa Applications PUHZ-S(H)W OUTDOOR UNITS These split systems are ideal for pool & spa applications and require an external heat exchanger. The flexibility of this system allows the installer to position the heat exchanger right where the hot water is required for both new and retrofit installations. Vaportec HXTi with high density plastics and a titanium coil heat exchanger for swimming and spa pool heating will require mounting and installation of refrigerant pipe work to the PUHZ-SW outdoor unit. The system is controlled by the PAR-W21, 7 day timer/controller and an advanced PAC-IF031 (FTC2) interface. Key Features • Reliable, year-round water heating • Inverter driven for maximum energy efficiency • Operation in outdoor temperatures as low as -25°C • Easy to use LCD Wall Controller with 7 Day Timer • FTC2 intelligent controller for efficient temperature control PUHZ-SW50VKA(-BS) OUTDOOR UNIT* HEATING*1 (A7/W35) HEATING*2 (A2/W35) PUHZ-SW75VHA(-BS) PUHZ-SHW80/112VHA(-BS) PUHZ-SW120VHA(-BS) ZUBADAN ZUBADAN PUHZ-SW50VKA(-BS) PUHZ-SW75VHA(-BS) PUHZ-SW120VHA(-BS) PUHZ-SHW80VHA(-BS) PUHZ-SHW112VHA(-BS) Capacity (kW) 5.50 8.00 16.00 8.00 11.20 Power Input (kW) 1.24 1.82 3.90 1.72 2.51 COP 4.42 4.40 4.10 4.65 4.46 Capacity (kW) 5.00 7.50 12.00 8.00 11.20 Power Input (kW) 1.68 2.21 3.70 2.25 3.35 COP 2.97 3.40 3.24 3.55 3.34 FSW85 FSW85 FSW140 FSW85 FSW125 Vaportec HXTi Vaportec HXTi Vaportec HXTi Vaportec HXTi Vaportec HXTi FLOW SWITCH HEAT EXCHANGER Ancillary equipment such as water pumps and expansion tanks are to be provided separately by the installer, and selected to meet the individual system pressure and flow requirements. This system is supplied with the Vaportec HXTi Heat Exchanger. * For full outdoor specifcations see pages 10 to 11. *1 Under normal heating conditions at outdoor temp: 7°CDB / 6°CWB, outlet water temp 35°C, inlet water temp 30°C as tested to BS EN14511. *2 Under normal heating conditions at outdoor temp: 2°CDB / 1°CWB, outlet water temp 35°C, inlet water temp 30°C. VAPORTEC HEAT EXCHANGER WATER PIPE SIZE (mm) LIQUID / GAS PIPE SIZE (inch) DIMENSIONS (mm) WEIGHT (kg) HXTi 8 50mm PVC (max. pressure 4 bar) 3/8" and 5/8" Width 165 Depth 235 Height 640 4.4 Vaportec HXTi Heat Exchanger PAR-W21 Controller 15 Ecodan – Manufactured in the United Kingdom Mitsubishi Electric’s manufacturing facility in Livingston, Scotland produces Ecodan Air Source Heat Pumps, Controls and Cylinders for the UK and European markets. The production facility, custom-built by the company in 1994, currently employs 420 staff and includes specially adapted and scalable production lines for Ecodan Air Source Heat Pumps, a new Cylinder and a purpose-built Ecodan testing facility. Mitsubishi Electric’s manufacturing plants are all ISO14001 and ISO9001 registered, an international benchmark ensuring we meet and continually improve upon quality and environmental standards. Ecodan Full 5 Year Warranty Every Ecodan Air Source Heat Pump comes with a full 5 year warranty as standard, subject to the following conditions: • The Ecodan purchase and installation is registered with BDT. • The Ecodan must be installed and commissioned by an accredited BDT Installer. HOME AUTOMATION AND COMMERCIAL • Ecodan Systems are compatible with a range of home automation systems via modbus using the MelcoBEMS Mini Modbus Interface. • As part of a wider range of applications, commercial Ecodan products are also available. Please contact your local BDT Representative or branch nearest you for more details. www.mitsubishi-electric.co.nz Black Diamond Technologies Exclusive distributor of Mitsubishi Electric products in New Zealand. WELLINGTON AUCKLAND CHRISTCHURCH HEAD OFFICE BRANCH BRANCH 1 Parliament Street PO Box 30772 Lower Hutt 5040 Unit 1, 4 Walls Road PO Box 12726 Penrose, Auckland 1642 44 Halwyn Drive PO Box 16904 Hornby, Christchurch 8441 Phone (04) 560 9147 Fax (04) 560 9133 Phone (09) 526 9347 Fax (09) 526 9369 Phone (03) 341 2837 Fax (03) 341 2838 For more information on Ecodan Central Heating and Hot Water, please call our Customer Service Team on 0800 784 382 Be sure to ask for Mitsubishi Electric. Other brands share the 3-diamond logo, however they are separate to the Mitsubishi Electric brand and cannot supply the models, features or guarantees outlined in this brochure. All models, features and specifications are subject to change and amendment at anytime. Printed March 2018.