Feature and Function Guide of Bluetooth Neckloop
Charge Port
Volume Buttons
Call Button
Neckloop
Blue Indicator Light
Microphone
Physical Product
Illuminate
Get Connected in 4 Quick Steps
1. Charge Battery
2. Start Bluetooth on Cellphone
3. Pair Bluetooth and Cellphone
4. Test and Use
1. Charge Bluetooth Battery for 2 Hours
A. Plug AC power charge into the end of bleutooth
The bluetooth indicator light turns on when the battery is charging
It may take up to 1 minute for the light to turn on.
When full charged (about 2 hours), the light will turns off.
B. Unplug the AC power adaptor
Note: Bluetooth is not funtional while charging. Charge from PC is applicable.
2. Start Bleutooth Feature on Your Phone
Your cellphone's Bluetooth feature is off by default. To use bluetooth neckloop, turn on the Bluetooth feature.
For most Motorola cell phones:
A. Select Menu > Settings > Connections > Bluetooth Link > Setup.
B. Scroll to Power
C. Press Change
D. Scroll to On
E. Press Select to turn on the Bluetooth feature. Bluetooth feature remains on unitl you turn it off.
Note: These steps are for most Motorola cell phones. For other phones, see your phone's user's guide.
3. Pair Bluetooth and Cellphone
Before use neckloop, must pair it with your phone.
A. Put Bluetooth in paring mode
i. With the bluetooth power off, press and hold the call button for 6 to 10 seconds until the blue indicator light
turns on and remains steadily it. (The light will flash while you hold the call button)
ii. If the indicator light is flashing or does not remain steadily lit, turn off the bleutooth and repeat step i.
B. The phone to look for bluetooth (for most Motorola phones:)
i. Select Menu > Settings > Connection > Bluetooth Link > Handsfree > Look for Devices.
The phone lists all Bluetooth devices it finds.
ii. Select Motorola H500.
iii. Press OK or Yes to pair the bluetooth.
iv. Enter the password 0000 and press OK.
While bluetooth is successfully paired with your phone, the indicator changes from steadily lit to flashing.
Note: These steps are for most Motorola cell phones. For other phones, see your phone's user's guide.
4. Test and Use
Your phone and headset are now paired and ready to make and receive
calls after wear it in your neck. Make a call to test:
A. Wear the neckloop as right side photo showing.
B. Load battery and put earpiece in ear canal.
C. On your phone, dial the number you want to call.
D. If your phone and headset are successfully paired
you will hear voice after connected with the dialed number.
After you have successfully paired your phone and bluetooth,
you need not to repeat these initial steps each time you use bluetooth.
Troubleshooting
My phone does not find my bluetooth.
Make sure the blue light on your headset is steadily lit when your phone is searching for devices (see step 3)
My bluetooth worked before but now it's not working.
Make sure your phone is on and bluetooth feature is turned on (see step 2).
If you have confirm bluetooth feature is on in your phone, pair your phone and bluetooth again (see step 3)
Turn On and Off
To turn your bluetooth on, press and hold the call button until the indicator light flashes. Then release button.
To turn your bluetooth off, press and hold the call button until the indicator light flashes rapidly and then turns off.
Note: To conserve battery power, turn off your bluetooth when you don't lan to use it for a while.
Making Calls
Function
Make a voice dial call
End a call
Receive a call
Reject a call
Redial last call
Answer a second incoming call
Toggle etween two active calls
Join a 3-way call (Feature is phone/network dependent)
Put an active call on hold or resume a call on hold
Transfer a call from the phone to bluetooth
Disable or enable the indicator light
Mute or unmute a call
Action
Tap the call button and speak the name after the tone
Tap the call button
Tap the call button
Press and hole the call button until you hear a beep
Press and hole the call button until you hear a beep
Press and hold the call button (places first call on hold)
Press and hold the call button
Press and hold both volume buttons
Press and hole the call button until you hear a beep
Tap the call button
Press and hold both Volume buttons for 3~4 seconds
Tap both volume buttons
Indicator Lights
Indicator
Status
(With charger plugged in)
On (steady)
Charging
Off
Charging complete
(Without charger plugged in)
Off
Power off
On (steady)
Pairing mode
10 rapid flashes
Pairing successful
Slow pluse
Connected
Quick flash
Standby
Note: After 5 minutes of inactivity, the light stops
flashing to conserve power, but the bluetooth
remains in standby mode.
Audio Tones
Status
Audio Tone
Single high tone when
pressing volume button
Five rapid high tones
repeated every 60 sec
Ring tone
Single high tone
Single low tone
Dual high/low tone
Status
Volume at minimum
or maximum
Low battery
Incoming call
Pairing confirmation
Voice activation
Voice tag not
recognized
Single high tone
End call
Low to hight tone
Phone network not
available
Two ascednding tones Mute enabled
Two descending tones Mute enabled
Download PDF
Similar pages
Quick User Guide -Body worn TOD version
Quick User Guide -Body worn TA version
Basic Settings
Tanita HF820 User's Manual
Multi-User Listening System
Transfer Files using USB