Coffee Machine
Siro Touch 1200 series
Uni brewer - Bean to Filter
User Manual
Picture: SiroTouch 1200 series
Filename:
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
User Manual
SiroTouch 1200 series
Disclaimer Manufacturer:
Although this user manual has been put together with the utmost care, J.M. de Jong Duke
automatenfabriek b.v. accepts no liability for inaccuracies or omissions. No liability is
accepted for the consequences arising from operation of the equipment in accordance with
the information contained in these instructions.
J.M. de Jong Duke automatenfabriek b.v. reserves the right to alter specifications at any
time and without prior notification to the purchaser
All rights reserved
Copyright:
J.M. de Jong Duke automatenfabriek b.v. © 2011
The contents of this manual are copyrighted. Texts, images, and source files may only be
used for professional purposes.
No part of this guide may be reused, modified, or published without the prior written
permission of the manufacturer.
Printing pages is allowed only for professional use.
Manufacturer:
De Jong DUKE
+31 (0) 184 496767
Postbus 190
+31 (0) 184 416059
3360 AD SLIEDRECHT
www.dejongduke.com
The Netherlands
support@dejongduke.nl
De Jong DUKE North America
+1 734 403 1708
12680 Delta Street
+1 734 403 1712
Taylor, MI, 48180
www.dejongduke.com
U.S.A.
support@dejongduke.com
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 2 of 36
User Manual
SiroTouch 1200 series
The machine supplier/ dealer is:
Company name:
Address:
Area code – City:
Country:
Telephone:
Fax:
Internet:
e-mail:
For service and support, always contact the dealer / supplier of the machine by using the
telephone service number below.
Tel. Service Number:
Preface:
●
●
●
●
●
●
●
●
●
Carefully read this instruction manual before you operate the machine.
Keep this manual in a safe place for possible later reference.
The manual cannot be regarded as a replacement for the training and instruction, but
must be seen as an addition to the training, and as a reference work.
This user’s manual is valid for the machine supplied by the manufacturer, including the
options installed by the manufacturer. The manufacturer accepts no liability for any
damage resulting from incorrect or improper use of the machine, or resulting from
modifications that have not been authorized by the manufacturer.
This manual gives instructions on the operation and maintenance of the machine.
Moreover, it gives solutions to simple malfunctions that may occur. The instructions in
some paragraphs are meant only for persons who are trained in the operation and
maintenance of the machine.
Besides this manual, a technical manual is also available.
This technical manual gives directions for solving machine malfunctions and repairing
the machine.
For instructions on the installation of the machine, a separate installation manual is
available.
Always use original parts from the manufacturer when the machine needs to be
repaired.
Only properly trained personnel may carry out repairs, install the machines, or transport
the machines.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 3 of 36
User Manual
SiroTouch 1200 series
Index:
Disclaimer Manufacturer: ......................................................................................... 2
Copyright: ............................................................................................................. 2
Manufacturer: ........................................................................................................ 2
The machine supplier/ dealer is: ............................................................................... 3
Preface: ................................................................................................................ 3
Index: ................................................................................................................... 4
1.
Safety ............................................................................................................. 5
1.1
Safety and Risk levels: .................................................................................. 5
1.2
Safety and Warnings ..................................................................................... 6
1.3
Standards and norms: ................................................................................... 7
2.
Description of the machine: ............................................................................... 8
2.1
General: ...................................................................................................... 8
2.2
The front of the machine:............................................................................... 8
2.3
Overview of the machine interior: ................................................................... 9
2.4
Type plate:..................................................................................................10
2.5
Technical specifications: ................................................................................11
3.
Before use: ....................................................................................................12
3.1
Installation:.................................................................................................12
3.2
Operation site:.............................................................................................12
3.3
Putting the machine out of order:...................................................................12
3.4
Measure of cup and jug heights .....................................................................13
4.
Operation:......................................................................................................14
4.1
Operating the machine in free vend mode: ......................................................14
4.2
Operating the machine in pay mode: ..............................................................14
4.3
Jug dispensing: ............................................................................................15
5.
Maintenance and filling: ...................................................................................16
5.1
Daily maintenance........................................................................................16
5.2
Weekly maintenance: ...................................................................................17
5.3
Monthly maintenance: ..................................................................................18
Cleaning the canister with water: ..........................................................................18
Cleaning the brewer with water: ...........................................................................18
5.4
Place safety key: ..........................................................................................19
5.5
Cleaning cycle for coffee brewer: ...................................................................20
5.6
Fill canisters: ...............................................................................................21
5.7
Change filter paper: .....................................................................................23
5.8
Fill up bean canister (if applicable): ................................................................24
5.9
Removal of the brewer: ................................................................................26
5.10 Install the brewer: .......................................................................................27
5.11 Assembling and disassembling the brewer chamber: ........................................28
5.12 Disassembling the mixing system: .................................................................29
5.13 Assembling the mixing system: .....................................................................31
6.
Failure and Error messages: .............................................................................33
Document control: .................................................................................................34
Notes: ..................................................................................................................35
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 4 of 36
User Manual
SiroTouch 1200 series
1. Safety
1.1
Safety and Risk levels:
Four safety and risk levels are used in this manual.
The risk levels and explanations are described below.
Danger:
To warn persons / readers about the possibility of
serious or fatal injury to themselves or others.
Warning:
To warn persons / readers about the possibility of
minor injury to themselves or others.
Caution:
To warn persons / readers about possible damage to
equipment or data or about potential problems in the
outcome of what they are doing.
Note:
To emphasize points or remind persons / readers of
something, or to indicate minor problems in the
outcome of what they are doing.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 5 of 36
User Manual
SiroTouch 1200 series
1.2
Safety and Warnings
The general safety warnings apply to the entire document.
The risk level associated with the explanation below.
Danger:
Do not use water in or near the machine unless the
instructions contain explicit directions to the
contrary.
Risk of electrocution when water comes in contact with
internal electrical parts.
HOT water! The water system (boiler, pipes, etc.)
may contain hot water
Risk of burning when HOT water comes in contact with a
person that can cause a scalding injury.
Warning:
Do not shake the machine while in use.
Risk that machine can tip and fall.
Risk of electrocution when water comes in contact with
internal electrical parts.
Do not lean on the door when open.
Risk that machine can tip and fall.
Caution:
Note:
Do not use aggressive cleaning products or
abrasives to clean (parts of) the machine.
Do not use a damaged machine.
Please contact your supplier
If a fault occurs, disconnect the machine from the
electrical and water supplies.
Please contact your supplier immediately.
Keep this manual near the machine, so the manual is
immediately available.
Use the machine only in areas where trained personnel can
monitor the operation.
Damaged water connection tubes may only be repaired by
trained personnel.
The water connection must conform to local regulations.
Do not use an extension cord.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 6 of 36
User Manual
SiroTouch 1200 series
1.3
Standards and norms:
The machine is build according to CE norms
The machine complies with the following standards:
● Machine standard: 89/392/EEG
● EMC standard: 89/336/EEG,
The machine complies with the following norms:
● EN 292: safety of machines.
● UL and cUL 751: norm vending machines (only if sign is on type plate)
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 7 of 36
User Manual
SiroTouch 1200 series
2. Description of the machine:
2.1
General:
Warning:
Hot drinks are dispensed from the machine
Take care to avoid scalding yourself.
If cups or jugs are not correctly placed
The machine will spill hot liquid down the front.
This can cause serious burns.
The outlet of the machine may occasionally drip hot
liquid even when the machine is not in use.
When the hot water comes in contact with a person, this
can lead to serious burns.
The water system (boiler, tubes etc.) contains hot
water with a temperature close to the boiling point
<100 °C.
When the hot water comes in contact with a person, this
can lead to serious burns.
The machine is a compact semi-automatic machine for the preparation and vending of hot
drinks. Your supplier can adjust the taste and sizes of the drinks.
2.2
The front of the machine:
The machine can be operated using the operating panel on the door. By pushing one of the
selection buttons on the screen, a product choice can be made.
Before you dispense a beverage, a cup must be placed under the tap.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 8 of 36
User Manual
SiroTouch 1200 series
2.3
Overview of the machine interior:
Bean canister
lid & lock
Lid
Bean canister
Base cabinet
Bean canister
lock
Instant canisters
Service lock
Grinder
Outlet tube(s)
Mains Power
switch
Mixing bowls
Brewer chamber
mixers
Uni Brewer
Brewer outlet
Dispensing
nozzles
Waste bucket
Filter paper rol
Drip tray
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 9 of 36
User Manual
SiroTouch 1200 series
2.4
Type plate:
The type plate is mounted on the inside of the machine, at the top left.
The following data is mentioned on the type plate:
●
Name of manufacturer
●
●
●
●
●
●
Serial number
Type/model specification
Model specification
Mains power specification
Production date
Water connection specification
Remark: data on type plate differs based on model.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 10 of 36
User Manual
SiroTouch 1200 series
2.5
Technical specifications:
Dimensions of the machine:
Height:
with bean canister:
with bean extended canister:
Width:
Depth:
Weight (empty):
Electricity:
Mains supply (Europe):
Frequency:
Max. capacity:
Mains supply (North America):
Frequency:
Max. capacity:
Water pressure:
Minimum pressure:
Maximum pressure:
Water connection:
Sound pressure:
795
875
1025
370
530
mm
mm
mm
mm
mm
45
99.2
Kg
lb.
+/+/-
10
10
%
%.
230
50 ~ 60
2,4
V AC
Hz
kW
+/+/-
10
2
%
%
115
50 ~ 60
1.2
V AC
Hz
kW
+/+/-
10
2
%
%
90
600
¾
< 70
in
in
in
in
in
kPa
(0,9 bar)
kPa
(6,0 bar)
BSP connection
dB(A)
Ambient temperature in storage:
Ambient temperature in operating:
+5
+5
°C
°C
Optional:
Dimensions of the Base Cabinet:
Height:
Width:
Depth:
850
370
530
mm
mm
mm
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
31.2
34.4
40.3
14.5
20.9
~
~
+ 50
+ 40
°C
°C
33.5
14.5
20.9
in
in
in
Page 11 of 36
User Manual
SiroTouch 1200 series
3. Before use:
3.1
Installation:
Installation, transportation, and adjustment of the machine is specialized work. Only
properly trained service personnel should carry this out.
For instructions about transportation, unpacking, and installation of the machine, see the
technical manual.
3.2
Operation site:
These machines may only be used indoors, in a hygienic dry room, with a temperature
between 5 and 40 degrees Celsius.
Place the machine on a flat, stable surface.
3.3
Putting the machine out of order:
If the machine will not be used for a long period of time (for example: during the
weekend,) it is recommended to turn off the water supply and the electricity (pulling the
plug from the socket is sufficient). This will prevent unnecessary use of energy.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 12 of 36
User Manual
SiroTouch 1200 series
3.4
Measure of cup and jug heights
CUP
Measure A:
Max cup diameter:
70
mm
2.76
in
Measure B:
Mounted default
Max cup height:
110
mm
4.33
in
Mounted low
Max cup height:
125
mm
4.92
in
Mounted high
Max cup height:
95
mm
3.74
in
Mounting high is discontinued from
serial numbers 201106xxxxxxx
Min height:
Able to receive a volume of consumption
JUG
Measure A:
Max Jug diameter:
135
mm
5.31
in
Measure C:
Max jug height:
180
mm
7.08
in
Optional:
With higher machine elevation unit for jugs.
Measure D is:
Measure C:
Max jug height:
Measure D is:
Measure C:
Max jug height:
50
mm
1.97
in
220
mm
8.66
in
120
mm
4.72
in
300
mm
11.81
in
Min height:
Able to receive a volume of consumptions.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 13 of 36
User Manual
SiroTouch 1200 series
4. Operation:
4.1
Operating the machine in free vend mode:
Warning:
Note:
Risk of burn injuries when taking out the HOT
beverages.
When the hot beverages come in contact with a person, this
can lead to serious scalding injuries.
If cups or jugs are not correctly placed.
The machine will spill hot liquid down the front.
This can cause serious scalding injuries.
The outlet of the machine may occasionally drip hot
liquid even when the machine is not in use.
When the hot liquid comes in contact with a person, this can
lead to serious burn scalding injuries.
The water system (boiler, tubes etc.) contain hot water
with a temperature close to the boiling point <100 °C.
When the hot water comes in contact with a person, this can
lead to serious scalding injuries.
Place the cup in the centre of the cup stand.
All beverage selections are dosed on the left cup stand.
Except the selections of hot water and chilled water they are
dosed on the right cup stand.
1.
2.
3.
4.
Place a cup under the outlet on the cup stand.
Select your desired drink.
Follow the instructions on the screen.
After pressing the start button, the machine prepares your drink and dispenses it into
the cup.
5. Your drink is ready after the beep and the message ‘ready’ is on the screen.
4.2
Operating the machine in pay mode:
In pay mode, first insert the required money and continue with step 1 of the free vend
operation.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 14 of 36
User Manual
SiroTouch 1200 series
4.3
Jug dispensing:
Warning:
1.
2.
3.
4.
5.
6.
7.
Risk of burn injuries when taking out the HOT
beverages.
When the hot beverage comes in contact with a person,
this can lead to serious scalding injuries.
If cups or jugs are not correctly placed.
The machine will spill hot liquid down the front.
This can cause serious scalding injuries.
The outlet of the machine may occasionally drip hot
liquid even when the machine is not in use.
When the hot liquid comes in contact with a person, this
can lead to serious scalding injuries.
The water system (boiler, tubes ect.) contain hot
water with a temperature close to the boiling point
<100 °C.
When the hot water comes in contact with a person, this
can lead to serious scalding injuries.
Push the cup stand up.(picture 4.3.1)
Place a jug under the outlet.(picture 4.3.2)
Select the jug button.
Select the drink and jug size.
Select the start button.
The machine dispenses the selected drink into the jug.
Your drink is ready after the beep and the message ‘ready’ is on the screen.
Jug placement
picture 4.3.1
picture 4.3.2
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 15 of 36
User Manual
SiroTouch 1200 series
5. Maintenance and filling:
5.1
Daily maintenance
Failing to perform the daily maintenance negatively affects the quality of the beverages and
can lead to malfunctioning of the machine.
1.
2.
Open the door of the machine.
Install the safety key (see paragraph: install safety key)
Flush mixers and brewer:
3. Place a jug underneath the nozzle to
collect the hot water.
4. Press the “rinse daily” button on the
screen. Hot water from the boiler flows
through the brewer and mixers.
5. Repeat step 4 until clean water comes
out of the machine
Check if there are still enough ingredients in the canisters.
If necessary, fill up the canisters, following instructions in paragraph “Fill up
canisters”.
Empty waste bucket and drip tray:
1. Remove the drip tray, the cup stand and
the drip grid.
2. Remove the drip tray under the brewer.
3. Rinse the drip trays, cup stand and grid
in hot water.
4. Remove the waste bucket
5. Empty the bucket and rinse it in hot
water.
Clean the outside of the machine:
1.
2.
3.
4.
Clean the outside of the machine with a soft damp cloth.
Install the drip trays, grid, and cup stand.
Remove the safety key.
Close the door of the machine, and leave the service mode.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 16 of 36
User Manual
SiroTouch 1200 series
5.2
Weekly maintenance:
Failing to perform the weekly maintenance negatively affects the quality of the beverages
and can lead to malfunctioning of the machine.
1.
Open the door of the machine
Clean the mixing system:
2. Remove the mixing system according to paragraph “Disassembling the mixing bowl”.
3. Rinse out all loose parts of the mixing system in warm water.
4. Clean the parts of the mixing system that remain in the machine with a wet brush.
5. Mount the mixing system according to paragraph “Assembling the mixing bowl”. Make
sure that the parts are dry before you mount them.
Check if there are still enough ingredients in the canisters.
If necessary, fill up the canisters, following instructions in paragraph “Fill up
canisters”.
Clean cycle brewer:
1.
2.
3.
4.
5.
Place a jug underneath the nozzle to collect
the hot water
Install the safety key.
Press the “Weekly cleaning cycle brewer”
button on the screen.
Follow the instructions in the screen:
a.
Press start to close the brewer
b.
Brewer then moves to closed position
c.
Place 1 liter jug under outlet.
d.
Place tablet in brewer.
e.
Press button to run cleaning cycle.
Hot water from the boiler flows through the
brewer
See paragraph “cleaning cycle for brewer” for
detailed information.
Empty waste and drip tray bucket
1. Open the door.
2. Remove the drip tray, the cup stand and
the grid.
3. Rinse the drip trays, cup stand and grid
in hot water.
4. Remove the waste bucket
5. Empty the bucket and rinse it in hot
water.
Clean the outside of the machine:
1.
2.
3.
4.
Clean the outside of the machine with a soft damp cloth.
Install the drip trays, grid and cup stand.
Remove the safety key
Close the door of the machine, and leave the service mode.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 17 of 36
User Manual
SiroTouch 1200 series
5.3
Monthly maintenance:
Failing to perform the monthly maintenance negatively affects the quality of the beverages
and can lead to malfunctioning of the machine.
Apart from the weekly maintenance, the following tasks must be performed monthly to
ensure the machine operates correctly and optimal beverage quality is maintained.
Cleaning the canister with water:
Warning:
1.
Open the door.
2.
Lift the upper lid.
3.
Remove the canister from the machine.
4.
Remove the lid from the canister.
5.
Empty the canister.
Do not fill the canister while it is not completely
dry.
The product may form lumps, which makes the system
unusable.
6.
Rinse out the canister with warm water until
all product residues are removed.
7.
Dry the canister very thoroughly on the inside
and outside.
8.
Fill the canister and place it back in the
machine according to the procedure in
paragraph “Fill canisters”.
Cleaning the brewer with water:
1.
2.
3.
Remove the brewer from the machine according to the procedure in paragraph
“Removal of the brewer”.
Rinse the brewer with warm water.
Place the brewer back according to the procedure in paragraph “Install the brewer”.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 18 of 36
User Manual
SiroTouch 1200 series
5.4
Place safety key:
Warning:
The machine is now powered up with open door.
Parts in the machine can move automatically and hot water
can flow out.
Open the door and locate the safety key.
Insert the safety key and turn a quarter turn clockwise or counter clockwise.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 19 of 36
User Manual
SiroTouch 1200 series
5.5
Cleaning cycle for coffee brewer:
Run the cleaning cycle for the coffee brewer weekly using the cleaning tablet.
Note:
Not cleaning the brewer can cause the machine to
malfunction!
Note:
Failure to clean the brewer weekly with the cleaning
tablet delivered by the manufacturer will void the
warranty on related parts.
1.
Open the door of the machine.
2.
The service menu is displayed.
3.
Select the weekly cleaning cycle button.
4.
Follow the instructions on the screen of the “Cleaning
Cycle”
5.
Select start to close the brewer.
6.
7.
Brewer moves now to closed
position
Place de safety key in the door
8.
Place tablet in brewer.
9.
Place 1 liter jug under outlet
10.
Select the button to run cleaning
cycle
11.
The cleaning cycle is started and takes ± 5 minutes.
Wait till the cycle is finished
Close the door and run a test consumption to test the
machine
12.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 20 of 36
User Manual
SiroTouch 1200 series
5.6
Fill canisters:
Do not fill the canisters further than necessary for one or two days. This will keep the
products fresh. Make sure that the canisters remain filled with a layer of at least 4-cm of
product. Only use products that are recommended by the supplier of the machine.
1.
Filling the canisters must be done outside the machine.
To facilitate taking out the canisters, the lid of the machine
can be flipped up (after opening the door).
Perform the following procedure to fill a canister:
2.
Turn the nozzle of the canisters upwards
3.
Slightly lift up the canister at the front, until the positioning
ridge comes out of the hole.
4.
Pull the canister towards the front and take it out of the
machine.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 21 of 36
User Manual
SiroTouch 1200 series
5.6
Fill canisters:
5.
Fill the canister with the product indicated on the canister.
Place the lid back on the canister.
6.
Place the canister back in the machine. Make sure the drive
at the back of the canister fits well on the motor drive.
7.
Push the canister at the front over the positioning ridge.
8.
Turn the nozzle of the canister downwards.
Check the position of the nozzle of the canister. It must be
positioned correctly above the brewer or mixing bowl.
9.
10.
Close the door or place safety key.
Flush the mixers.
This is necessary because product may fall into the mixers
when the canister is place back into the machine.
11.
Check correct functioning by taking test beverages.
Picture may be different based on model.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 22 of 36
User Manual
SiroTouch 1200 series
5.7
Change filter paper:
Caution:
Make sure that the brewer is not moved down during
lifting of the transport wheels. Push the cantilever down
with your thumb while supporting the brewer with your
index finger.
1
Perform the following procedure for changing of the paper roll:
1. Open the door of the machine.
2. Install
1
the safety key.
3. Tear
2 off the filter paper for the brewer.
4. Press
3
the replace filter paper button. Wait till the brewer turns to the “open” position
5. Remove
4
the old filter paper (3) from the brewer (1), lifting the transport wheels (2)
with the cantilever if necessary.
6. Place the new roll filter paper and guide the filter paper to the brewer and transport
wheels.
7. Push
5
button replace filter paper. The brewer moves a cycle and stops.
8. Check
6
if the filter paper is being transported correctly, and that no folds and creases
are in the paper.
9. Check
7
the functioning of the machine by taking a test drink (coffee).
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 23 of 36
User Manual
SiroTouch 1200 series
5.8
Fill up bean canister (if applicable):
Note:
10.
11.
12.
13.
14.
15.
16.
17.
8
9
10
When filling the bean canister the green locking
handle must be fully pulled out.
When the green handle is not fully pulled out it is possible
that coffee bean can fall out
1
2
Open the door.
Locate
1
the green locking handle under at the bean canister.
Pull
2 the green locking handle towards you to unlock the canister.
Lift
3 the bean canister up and take it out the machine.
Place
4
the bean canister on a stable ground.
3
5&6
7
8
Place
5
the key into the lock of the canister lid.
Unlock
6
the canister lid.
Remove
7
the canister lid.
Check the position of the green handle is fully pulled out.
When the green handle is not fully pulled out it is possible that coffee bean can fall out.
Fill the canister with fresh coffee beans.
Place the lid back on the canister and lock it.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 24 of 36
User Manual
SiroTouch 1200 series
5.8
18.
19.
20.
21.
Fill up bean canister (if applicable):
11
12
13
Place
1
the bean canister back into the coffee machine on the 4 position ridges of the
grinder.
1
Posh the green locking handle back to lock the bean canister on the grinder.
Close the upper coffee machine lid.
Controleer de werking door een testconsumptie te nemen.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 25 of 36
User Manual
SiroTouch 1200 series
5.9
Removal of the brewer:
Removal of the brewer is necessary for performing the monthly maintenance. Only
properly trained personnel may work on the brewer itself. Instructions for performing work
on the brewer are described in the technical manual.
Caution:
Make sure that the machine is switched off and cannot
be accidentally switched on.
Carry out the following procedure for removal of
the brewer:
1.
2.
3.
4.
5.
Open the door of the machine.
Move up the lid of the machine.
Take out the canisters of the machine.
Tear off the filter paper to the left and right of
the brewer
Remove the nozzle of the brewer.
Take the brewer out of the machine by pulling
the bottom to the front and slide the brewer
upward out of the suspension
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 26 of 36
User Manual
SiroTouch 1200 series
5.10 Install the brewer:
Installationof the brewer is necessary for performing the monthly maintenance. Only
properly trained personnel may work on the brewer itself. Instructions for performing work
on the brewer are described in the technical manual.
Caution:
When the machine is switched on, you should
take the utmost care when performing the
functions via the internal service panel.
Carry out the following procedure to install the
brewer:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Make sure the brewer is in stand-by mode;
the interlocking (B) must be right adjusted.
You can adjust the drive of the brewer with
the blue brewer key, delivered with the
machine.
Place the brewer with both ridges (1) in both
holes (4), see (A).
Push the bottom backwards, so that the
drives (2) of the brewer and the motor are
interlocking.
This may take some force, see (B).
Place the outlet pipe on the brewer.
Guide the filter paper through (see paragraph
change filter paper).
Switch the machine on.
Push button replace filter paper to move the
brewer through a cycle.
Check if the filter paper is being transported
properly.
Check the functioning of the machine by
taking a test drink
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 27 of 36
User Manual
SiroTouch 1200 series
5.11 Assembling and disassembling the brewer chamber:
Removal of the brewer is necessary for performing the monthly maintenance. Only properly
trained personnel may work on the brewer itself. Instructions for performing work on the
brewer are described in the technical manual.
Caution:
When the machine is switched on, you
should take the utmost care when
performing the functions via the internal
service panel.
Disassembling the brewer chamber:
1.
Press Replace filter paper button.
2.
Remove brewer chamber by pulling it
towards you
Assembling the brewer chamber:
1.
Press the brewer chamber with the two
pins into its position.
2.
Press the replace filter paper button to
check if the brewer runs a cycle smoothly.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 28 of 36
User Manual
SiroTouch 1200 series
5.12 Disassembling the mixing system:
1. Open the door.
2. Remove the mixers using the following procedure.
3. Remove the outlet pipes from the mixers.
4. Turn the bayonet catch counterclockwise (approx. 10º).
5.
Remove the mixer house.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 29 of 36
User Manual
SiroTouch 1200 series
5.12 Disassembling the mixing system:
6.
Pull the mixer parts towards you.
7.
Pull the whipper blade towards you and off the shaft.
8.
Turn the base plate counterclockwise and pull it towards
you.
9.
Ready
Picture may be different based on model.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 30 of 36
User Manual
SiroTouch 1200 series
5.13 Assembling the mixing system:
Caution:
1.
Procedure to assemble the mixer.
2.
Install the base plate.
The arrow on the whipper blade must on the flat side
of the mixer shaft.
3.
Install the whipper blade.
Be sure that the arrow is
at the flat side of the shaft.
4.
Install the mixer house.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 31 of 36
User Manual
SiroTouch 1200 series
5.13 Assembling the mixing system:
5.
Turn the bayonet catch clockwise until it is locked.
6.
Install the outlet pipes on the mixers.
7.
Close the door.
8.
Check correct functionality by taking test beverages.
Picture may be different based on model.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 32 of 36
User Manual
SiroTouch 1200 series
6.
Failure and Error messages:
Always check whether an error message is shown on the display. If no error message is
shown and the machine does not work correctly, you may find the possible cause and
solution in the following table. For failures not mentioned in this manual, contact the service
engineer.
Rinse brewer with tablet
The weekly cleaning cycle is required. Run the cleaning cycle and the message will
disappear.
Brewer not in home position
Consult the service engineer
Communication error
Consult the service engineer
Cleaning Error
Cleaning cycle did not finish. Run the cleaning cycle again and finish it correctly.
Door open
Close door or install service key to run the machine.
Drip tray/waste bucket full
Empty the drip tray in front of machine and the waste bucket, make sure the probes are
dry.
Filling boiler
Wait until boiler is filled.
If message is still shown after 10 minutes, consult the service engineer
Grinder blocked
Grinder is blocked and needs to be cleaned out
Heating boiler
Wait until boiler is heated.
If message is still shown after 10 minutes, consult the service engineer
Install new filter paper
Filter roll is empty. Install a new filter roll
Mixer blocked
Clean the mixing bowl
No water connected
No water detected for more than 2 minutes in open boiler system.
Open and close the machine door for restart.
Open boiler leaking, inlet closed
A leak is detected. Close water tap and consult the service engineer.
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 33 of 36
User Manual
SiroTouch 1200 series
Place cup left or Place cup right
Cup needs to be placed under the dispenser before the start button is available.
Water filter installed?
Consult the service engineer.
Replace water filter
Consult the service engineer
Shortcut temp.sensor
Consult the service engineer
Temp. sensor disconnected
Consult the service engineer
Temp. boiler to high
Consult the service engineer
Water level to low
Consult the service engineer
Document control:
Date:
Version:
Reason of change:
Resp.
2012-09-24
2012-10-05
2013-02-04
v01-00
v01-01
v01-02
Initial release
Corrections
correction specification
DH
DH
DH
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 34 of 36
User Manual
SiroTouch 1200 series
Notes:
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 35 of 36
User Manual
SiroTouch 1200 series
SiroTouch-1200_9FND_UserManual_5DUFNH20b_EN_v01-02.docx
Page 36 of 36