SYSTEM 3
HIGH RATE SAND FILTERS
O
W
N
E
R’
S
M
A
N
U
A
L
INSTALLATION, OPERATION & PARTS
MODELS
S7S50
S8S70
This manual should be furnished to
the end user of this filter; its use will
reduce service calls and chance of
injury and will lengthen filter life.
Sta-Rite Pool/Spa Group
293 Wright Street, Delavan, WI 53115
International: 262-728-5551, FAX: 262-728-7550
www.starite.com
Union City, TN • Delavan, WI • Mississauga, Ont. • Murrieta, CA
© 2004, Sta-Rite Industries
Printed in U.S.A.
S282 (Rev. 4/20/04)
HIGH RATE SAND FILTERS
To avoid unneeded service calls, prevent possible injuries, and get the most
out of your filter, READ THIS MANUAL CAREFULLY!
The Sta-Rite System 3 High Rate Sand Filter:
• Is designed to filter water for swimming pools.
• Is an excellent performer; durable, reliable.
Table of Contents
Safety Instructions.....................................................................................2-3
General Information/Specifications ..............................................................4
Installation ...................................................................................................5
Initial Filling.................................................................................................6
Filter Disassembly/Assembly.....................................................................6-7
Startup/Operation .......................................................................................7
Backwash ....................................................................................................8
Maintenance.............................................................................................8-9
Replace Internal Assembly ...........................................................................9
Winterizing ..................................................................................................9
Repair Parts List ....................................................................................10-11
Troubleshooting Guide...............................................................................12
Warranty....................................................................................................15
READ AND FOLLOW SAFETY
INSTRUCTIONS!
This is the safety-alert symbol. When you see this symbol on your valve or in
this manual, look for one of the following signal words and be alert to the potential for personal injury.
DANGER warns about hazards that will cause serious personal injury, death or
major property damage if ignored.
WARNING warns about hazards that can cause serious personal injury, death
or major property damage if ignored.
CAUTION warns about hazards that will or can cause minor personal injury or
property damage if ignored.
The label NOTICE indicates special instructions which are important but not
related to hazards.
Carefully read and follow all safety instructions in this manual and on filter.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
2
Incorrectly installed or tested equipment may fail, causing severe injury or property damage. Read and follow instructions
in owner's manual when installing and operating equipment.
Have a trained pool professional perform all pressure tests.
1. Do not connect system to a high pressure or city water system.
2. Use equipment only in a pool or spa installation.
3. Trapped air in system can cause explosion. BE SURE all air is out of system
before operating or testing equipment.
Before pressure testing, make the following safety checks:
• Check all clamps, bolts, lids, and system accessories before testing.
• Release all air in system before testing.
• Tighten Sta-Rite pump trap lids to 30 ft. lbs. (4.1 kg-cm) torque for testing.
• Water pressure for test must be less than 25 PSI (172 kPa).
• Water temperature for test must be less than 100˚ F. (38˚ C).
• Limit test to 24 hours. After test, visually check system to be sure it is ready
for operation. Remove pump trap lid and retighten hand tight only.
NOTICE: These parameters apply to Sta-Rite equipment only. For non StaRite equipment, consult manufacturer.
BEFORE WORKING
ON FILTER:
If filter clamp is
adjusted under pressure, tank will blow
off of base, causing
severe injury or major
property damage.
1. Stop pump.
2. Open air release
valve.
3. Release all pressure
from system.
BEFORE WORKING
ON PUMP OR MOTOR
Filter pumps require
hazardous voltage
which can shock,
burn, or cause death
3
Disconnect power to
motor.
GENERAL INFORMATION
• Clean a new pool as well as possible before filling pool and operating filter.
Excess dirt and large particles of foreign matter in the system can cause serious damage to the filter and pump.
Hazardous pressure.
Can cause severe
injury or major
property damage
from tank blow up.
Do not operate filter at water temperatures above 120°F (65.5°C).
NEVER operate this filter system at more than 50 pounds per square
inch (50 PSI/345kPa) pressure!
Release all pressure
and read instructions
before working on filter.
TABLE I - OUTLINE DIMENSIONS IN INCHES (mm)
Sand
Model
A
B
S7S50 28-1/2(724)
S8S70 32-1/2(825)
C
No. of Clamps
42(1067)
42-1/4(1073)
7
8
D
E
F
36(914) 53-1/2(1360) 2” NPT
40(1020) 54-1/4(1380) 2” NPT
D
A
TABLE ll - FILTER SPECIFICATIONS AND OPERATING INFORMATION
FILTER MODEL:
E
C
INLET
Filter Area
Flow Rate Range
Public Pool Flow Rate
Max. Operating Pressure
Freeboard (See Fig. 1B)*
Turnover in Hours:
6 Hours
8 Hours
10 Hours
Qty. of Media Required:
Cu. Ft.
Weight (Pounds)
B
OUTLET
7.812"
19.85 cm
F
9.19"
23.3 cm
Figure 1 - Dimensions
DISTRIBUTOR
11" (28 cm)
FREE BOARD
12.5"
31.75 cm
11"
S7S50
S8S70
2.4 Ft.2(.223M2)
33-48 GPM(125-182 L/m)
48 GPM(182 L/m)
50 PSI(345 kPa)
11” (28 cm)
3.4 Ft.2(.316M2)
47-68 GPM(178-257 L/m)
68 GPM(257 L/m)
50 PSI(345 kPa)
11” (28 cm)
17,200 Gal.(65 102 liters)
23,000 Gal.(87 055 liters)
28,800 Gal.(109 008 liters)
24,400 Gal.(92 354 liters)
32,600 Gal.(123 391 liters)
40,800 Gal.(154 428 liters)
2(56 540cm3)
200(90,7 kg)
3(84 960cm3)
300(136 kg)
* Freeboard is the open space between the top of the sand bed and the tank backwash outlet.
SAND BED
NOTICE: 1 cubic foot (28 320 cm3) of sand weighs approximately 100 lbs. (45,4kg). DO NOT use
a finer grade of sand than recommended.
TANK
FLANGE
RECOMMENDED SAND GRADES:
Use only: #20 Silica Sand, Size Range .40-.55mm., Uniformity Coefficient less
than 1.75.
NOTICE: Use of other sands will reduce filter performance, may damage
pump,and will void warranty.
Recommended:
1. Wedron Silica/Best Sand Co., Sand Grade: Wedron .45-.55mm., Effective
Size .46mm, Uniformity Coefficient 1.22.
Figure 2 - Freeboard measurement 2. U.S. Silica - Silurian Filter Sand, Sand Grade.45-.55 mm., Effective Size
.48mm, Uniformity Coefficient 1.18.
14.0
6.0
Pressure Drop (PSI)
S7S50
4.0
10.0
S8S70
8.0
3.0
6.0
2.0
4.0
1.0
0
Pressure Drop (Feet)
12.0
5.0
2.0
0
10
20
30
50
40
Gallons Per Minute
60
70
80
015 0893
4
INSTALLATION
Installation of filter should only be done by qualified, licensed personnel. For
assembly and filling instructions, see pages 6 and 7.
Filter mount must:
• Provide weather and freezing protection.
• Provide space and lighting for easy access for routine maintenance. (See
Figure I and Table 1, Page 4, for space requirements.)
• Be on a reasonably level surface and provide adequate drainage.
• Be as close to pool as possible to reduce line loss from pipe friction.
Piping:
• Piping must conform to local/state plumbing and sanitary codes.
• Use pipe joint sealing compound or Teflon tape on all male connections of
metal pipe and fittings (except unions). Use Teflon tape or Plasto-Joint Stik1
on all male connections of plastic pipe and fittings. DO NOT use pipe dope
on plastic pipe; it will cause stress cracking of the pipe. Do not use sealant
or tape on unions – assemble them dry and hand tight.
• Do not damage union sealing surfaces and O-Rings.
• Support pipe independently to prevent strains on filter or valve.
• Use 2” pipe to reduce pressure losses as much as possible.
TABLE III - Sta-Rite valves
for use with filters
Port
Size
Part
Number
2"
1-1/2"
Multi-port
WC212-144P
WC212-143P
2"
Brass Slide
WC212-136D
2"
Plastic Slide
WC212-134P
NOTICE: Filter may be located away from pool, but for adequate flow larger
pipe may be needed. For more information about hydraulic design, call
Sta-Rite Customer Service.
• Fittings restrict flow; for best efficiency use fewest possible fittings.
• Keep piping tight and free of leaks: pump suction line leaks may cause
trapped air in filter tank or loss of prime at pump; pump discharge line
leaks may show up as dampness or jets of water.
• NOTICE: Overtightening can crack filter ports.
Valves:
• A check valve installed ahead of filter inlet will prevent contaminants from
draining back into pool.
• A check valve installed between filter and heater will prevent hot water
from backing up into filter and deforming internal components.
• Install Sta-Rite Two Position Slide Valve or Multiport Selector Valve with filter. See Table lll.
NOTICE: Use of valves
other than those listed
above could cause
reversed water flow
through filters and
damage to internal filter components.
• Filter ports and valve ports are furnished with union connections.
DO NOT use pipe sealants on union collar (nut).
• Use care before assembly not to damage union sealing surfaces or O-Ring.
Wastewater:
• Be sure all provisions for waste water disposal meet applicable local, state
or national codes. 100 gallons (379 liters) or more of pool water will be discharged during filter backwashing. Do not discharge where water will cause
flooding or damage.
Assembly:
See Pages 6 and 7 for assembly filling instructions.
1
Lake Chemical Co., Chicago, IL
5
FILTER DISASSEMBLY/ASSEMBLY
To avoid equipment damage and personal injury, never change handle
position on control valve while pump is running.
BEFORE DISASSEMBLING FILTER:
1. STOP PUMP.
2. OPEN air release valve and drain fitting.
3. WAIT until all pressure is released and water drained from filter tank
and system before loosening clamp knobs.
Disassembly:
Hazardous pressure.
Can cause severe injury or major property
damage from tank
blow up.
Release all pressure
and read instructions
before working on filter.
1. Backwash filter according to instructions under “Filter Backwash
Procedure”, Page 8 (when first filling a new filter, omit this step).
2. Stop pump.
3. Open air release valve (Key No.1, Page 10) on top of filter tank to release
all air pressure from inside of tank and system.
4. Remove filter drain plug (Key No. 17B, Page 10) and drain all water from
tank (see Figure 3). Hold drain fitting securely in filter body to avoid losing
sand.
5. To equalize flange stresses, loosen clamp knobs alternately (that is, on opposite sides of tank) around tank. Remove clamps.
6. Being careful not to damage Cord Ring (Key No.12, Page 10), lift upper
tank shell (Key No. 7, Page 10) off lower tank shell (Key No. 14, Page 10).
Filling Filter with Sand:
1. See Page 4 for correct sand grade and quantity.
HOLD
FOR
SAND
REMOVAL
ONLY
REMOVE
PLUG
Figure 3 - Hold drain fitting and remove drain plug to drain filter.
2. Before pouring sand into filter, look inside and check internal assembly
(Key No. 8, Page 10) for broken or loose laterals (Key No. 8A, Page 10)
caused by shipping damage. Replace if necessary.
3. To eliminate stress on laterals (Key No. 8A) fill tank half-full of water before loading sand.
4. When full, top of sand bed should be about 12-1/2” (31.75 cm) below top
of distributor (about 1-1/2” (3.8 cm) below tank flange (see Figure 2).
5. Wash all sand and dirt away from cord ring sealing area.
6. Assemble filter according to instructions, pages 6 and 7.
Assembly:
1. Remove cord ring slowly to avoid stretching or tearing it.
2. Inspect cord ring (Key No. 12, Page 10) for cuts, nicks, etc. If cord ring is
damaged, deformed, or has lost its resiliency, replace with a new one.
3. Clean cord ring area of tank shell (both halves) and cord ring.
4. Carefully install cord ring and upper tank shell (Key No. 7, Page 10).
NOTICE: Do not lubricate cord ring. Lubricants attract dirt and grit and
may (especially when petroleum based) damage cord ring and void warranty.
NOTICE: Be sure upper tank shell contacts cord ring surface evenly and
seal area is clean and free from dirt.
6
5. Install clamps. Do not tighten clamps yet.
1
5
6. See Figure 4 for clamp tightening sequence. Tighten all clamp knobs securely hand tight.
4
NOTICE: To equalize stresses on tank, be sure to tighten clamps in sequence shown. DO NOT work your way around the filter tightening adjacent clamps.
7. Install air relief valve and gauge assembly on tank.
3
6
Startup (Multi-port Valve):
1. With pump OFF, set valve to ‘BACKWASH’ position.
2. Open air release valve (Key No. 1, Page 10).
2
7
21" Filter
3. Start pump, circulating water backwards through filter to waste.
4. Close air release valve when a steady stream of water is expelled.
1
5. Run pump five minutes or until waste water is clear (this purges excess
fine particles from system).
7
5
6. Stop pump; set valve handle to ‘RINSE’ position.
7. Start pump; run pump for 15 to 30 seconds.
4
3
8. Stop pump; set valve to ‘FILTER’ position. Follow instructions under
Regular Operation’ (below) to place filter in service.
Startup (Slide Valve):
1. With pump OFF, raise handle to fully extended position.
6
8
2
2. Open air release valve (Key No. 1, Page 10).
3. Start pump, circulating water backwards through filter to waste.
25" Filter
4. Close air release valve when a steady stream of water is expelled.
Figure 4 - Clamp tightening sequence.
5. Run pump five minutes or until waste water is clear (this purges excess
fine particles from system).
6. Stop pump; lower handle completely to ‘FILTER’ position and pin in place.
Follow instructions under ‘Regular Operation’ (below) to place filter in
service.
REGULAR OPERATION
Do not operate this filter at more than 50 PSI (345kPa) under
any circumstances!
Run Filter:
1. With pump OFF, set valve to ‘FILTER’ position.
2. Fill trap on pump with water.
3. Open air release valve on top of filter assembly (Key No. 1, Page 10); start
pump.
4. When steady stream of water comes from air release valve, close the
valve.
5. With filter operating, record pressure gauge reading in owner’s manual.
When reading is 10 PSI (70kPa) above initial reading, backwash filter.
7
Backwash Filter (Multi-Port Valve):
To prevent equipment damage and possible injury, turn pump OFF before changing valve position.
1. With pump OFF, set valve to ‘BACKWASH’ position.
2. Open air release valve (Key No. 1, Page 10).
3. Start pump, circulating water backwards through filter to waste.
4. Close air release valve when a steady stream of water is expelled.
5. Backwash until water runs clear.
6. Stop pump; set valve to ‘RINSE’ position.
7. Start pump; run pump for one minute.
8. Stop pump; set valve to ‘FILTER’ position.
9. Filter is now ready for service.
10. Open air release valve and release ALL pressure from system.
11. Follow ‘Run filter’ procedure to restart system.
Backwash Filter (Slide Valve):
To prevent equipment damage and possible injury, turn pump OFF before changing valve position.
1. With pump OFF, raise valve handle to fully extended position.
2. Open air release valve (Key No. 1, Page 10).
3. Start pump, circulating water backwards through filter to waste.
4. Close air release valve when a steady stream of water is expelled.
5. Backwash until water runs clear.
6. Stop pump; lower handle completely to ‘FILTER’ position and pin in place.
7. Filter is now ready for service.
8. Open air release valve and release ALL pressure from tank and system.
9. Follow ‘Run filter’ procedure (above) to restart system.
MAINTENANCE
General:
• Wash outside of filter with a mild detergent and water. Rinse off with hose.
NOTICE: DO NOT use solvents to clean filter; solvents may damage plastic
components in system.
• Inspect sand bed at least once a year to remove foreign material which has
not been backwashed out of system.
Follow instructions on Pages 6 and 7 when disassembling and
assembling filter.
NOTICE: When the sand bed gets hard and crusty on top, remove all the
old sand and replace it with new sand.
NOTICE: Open air bleed valve and bleed all air from filter each time pump
is stopped and restarted.
Weekly Pool Equipment Inspection:
1. Check pressure during operation. When pressure is 10 PSI (70kPa) higher
than initial operating pressure, backwash filter (see instructions, page 7).
8
2. Skimmer basket - remove debris.
3. Stop pump, release all pressure from system. Remove trap cover and basket, remove debris.
19
4. Bleed air from filter each time system is started.
5. Check pump for leaks. If found, see pump owner's manual.
6. Check pump strainer lid for tightness. Do not overtighten!
Replace Internal Assembly:
1. Disassemble filter according to instructions in "Filter Disassembly" Page 6.
954 0594
20
Figure 5
Hazardous Pressure! To avoid severe injury and major property damage, follow instructions on Pages 6 and 7 when disassembling
and assembling filter.
2. Remove sand from filter.
3. Remove union adapters and tank fittings, (Key Nos. 19 and 20, Figure 5).
Turn Key Nos. 19 and 20 counterclockwise to remove.
4. Lift old internal assembly out of tank. (Figure 6)
5. Twist lock new laterals into hub on new internal assembly. (Figure 7)
6. Remove old O-Rings on tank fittings (Key Nos. 19 and 20) and install new
O-Rings provided. Be sure sealing area is clean.
955 0594
Figure 6
7. Drop new internal assembly into tank and secure with tank fittings
(Key Nos. 19 and 20, Figure 8).
8. To refill, reassemble, and restart filter, follow instructions in owner’s
manual.
To avoid severe injury or major property damage, exactly
follow “Assembly” instructions, Pages 6 and 7.
9. Follow “Startup” instructions in owner’s manual.
WINTERIZING
956 0594
1. Open air release valve; open all system valves. Position multiport valve
between port positions to allow air passage to all ports.
2. Remove drain plugs from trap, pump, valve and filter.
Figure 7
3. Drain system piping.
4. Cover with plastic or tarpaulin to protect from weather.
5. Protect from freezing.
19
20
957 0594
Figure 8
9
25
30
3
0
45
5
40
10
0
5
50
60
55
1
15 2
22
2
3
4
5
6
7
8
9
10
21
11
20
19
19a
16
18
12
13
17
16
12
14
15
10
2859 0597
REPAIR PARTS LIST
Key No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
19A
20
21
22
†•
•
•
•
Description
2" Gauge
Valve Assembly
Nipple
Adapter Bushing
O-Ring
Tank - Upper Half Kit*
Collector - Manifold Assem.
Air Bleed Filter
Vent Tube
Elbow - Male Parflex
Lateral
O-Ring
Plug (Sand Removal)
Drain Fitting
1-1/2" NPT Plug
O-Ring
Tank Fitting
Tank Fitting
Clamp Assembly
Clamp Bolt
Tank - Lower Half
Cord Ring
Valve and Gauge Assembly
(Includes Key Nos. 1-5)
Lateral Extension Adapter
Decal - Model Label
Decal - Warning
Decal - Operating Instruction
Qty.
Model S7S50
Model S8S70
1
1
1
1
1
1
1
1
1
1
16
2
1
1
1
2
1
1
**
**
1
1
33600-0023
WC212-120P
U37-16P
24900-0504
35505-1423
24851-9000
24900-0100
WC8-126
WC37-386P
WC78-84P
24900-0002
35505-1424
24900-0503
24900-0505
27001-0022S
35505-1425
24900-0500
24900-0501
24850-0101
24850-0010
24850-0102
24850-0008
33600-0023
WC212-120P
U37-16P
24900-0504
35505-1423
24851-9001
24901-0100
WC8-126
WC37-386P
WC78-84P
24900-0003
35505-1424
24900-0503
24900-0505
27001-0022S
35505-1425
24900-0500
24900-0501
24850-0101
24850-0010
24851-0103
24850-0009
as req'd
1
1
1
24850-0105
24700-0029
32155-4045
32165-4004
32155-4046
24850-0105
24700-0029
32155-4047
32165-4005
32155-4048
† Available for lateral repairs.
• Not illustrated
* Includes all decals and labels.
** Model S7S50 uses seven clamps and bolts; Model S8S70 uses eight.
11
TROUBLESHOOTING GUIDE
1. Short Cycle between backwashes:
NOTICE: Time between backwashes will vary with each installation and
between different areas of the country. Ask installer about normal backwash interval in your area. The following causes and remedies are for
cycle times shorter than normal for your area.
A. Flow rate too high or filter too small; consult dealer for system sizing
recommendations.
B. Water is chemically out of balance; consult pool serviceman.
Hazardous pressure.
Can cause severe injury or major property
damage from tank
blow up.
Release all pressure
and read instructions
before working on filter.
2. Low Flow/High Pressure:
A. Pipe blocked downstream from filter; remove obstruction.
B. Piping too small; use larger pipe (consult dealer for sizing).
C. Filter area too small or pump too large; consult dealer for recommendation.
3. Low Flow/Low Pressure:
A. Pump too small; consult dealer for recommendations.
B. Plugged pump, plugged line, or plugged hair and lint trap; clean thoroughly.
4. Pool Water Not Clear:
A. Water is chemically out of balance; consult pool professional.
B. Inadequate turnover rate; consult dealer about equipment sizing.
C. Sand in pool means broken lateral.
To avoid severe injury or major property damage, follow instructions under 'Disassembly' and 'Assembly' (pages 6 and 7)!
1. Follow filter disassembly procedure, Page 6.
2. Replace lateral according to instructions supplied with new lateral
(See Page 9).
3. Reassemble filter according to instructions, Pages 6 and 7.
12
13
14
STA-RITE LIMITED WARRANTY
Pumps, filters, skimmers, underwater lights (except bulbs),
accessories and fittings manufactured by Sta-Rite are warranted to be free of defects in material and workmanship for
one (1) year from date of installation.
Year from date
of installation
Product specific warranties:
HRPB, DEPB, System 3, and PL – Tanks . . . . . . . .10 years
Internal filter components and valves . . . . . . . . . 1 year
Max-E-Therm – Pool/Spa Heaters . . . . . . . . . . . . . 2 years
Heater Enclosure only (Upper RH & LH;
lower enclosure; and control board enclosure)… 10 years
Automatic Pool Cleaners including Hose . . . . . . . 2 years
Cristal-Flo filters – Tanks . . . . . . . . . . . .10 years pro-rated*
Valve and internal components. . . . . . . . . . . . . . . . 1 year
Posi-Flo II – Tanks . . . . . . . . . . . . . . . . . . . . . . . . . .10 years
Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year
PRC Cartridge –
Filter Tanks . . . . . . . . . .5 years pro-rated (1st 2 years full)
Elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year
System 2 Above Ground Systems – Tanks . . . . . . .10 years
Pumps / Platform and Internals . . . . . . . . . . . . . . . 1 year
Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year
When equipped with A.O. Smith
2-compartment motors (Does not include
pumps sold as part of a systems package) . . . . . . 2 years
Traps / In-Line Strainers . . . . . . . . . . . . . . . . . . . . . 1 year
Vertical Commercial Filter – Tanks . . . . . . . . . . . .10 years
Internals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year
Horizontal Commercial Filter
Tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 years
(Years 6-9, Prorated declining 20%/year, Yr. 10 - 10%)
Internals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year
▲
* Full warranty coverage is in effect for one year after installation. The pro-rated warranty covers the tank only during
the 2nd through 10th year after installation. The amount covered decreases by 10% each year. (ie., 2nd year 90% covered,
3rd year 80% covered, etc.).
The foregoing warranties relate to the original consumer purchaser (“Purchaser”) only. Sta-Rite shall have the option to repair or replace the defective product, at its sole discretion.
Purchasers must pay all labor and shipping charges necessary
to replace the product covered by this warranty. Requests for
warranty service must be made through the installing dealer.
This warranty shall not apply to any product that has been
subject to negligence, misapplication, improper installation
or maintenance, or other circumstances which are not in
Sta-Rite’s direct control.
This warranty sets forth Sta-Rite’s sole obligation and
Purchaser’s exclusive remedy for defective products.
STA-RITE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL,
INCIDENTAL OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE
DURATION OF THE APPLICABLE EXPRESS WARRANTIES
PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long
an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary
from state to state.
Supersedes all previous publications.
Sta-Rite Industries,
293 Wright St., Delavan, WI 53115
Retain Warranty Certificate (upper portion) in a safe and convenient location for your records.
DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation to:
▼
Sta-Rite, Attn: Warranty Dept., 293 Wright St., Delavan, WI 53115
Warranty Registration Card
Name
Years pool has been in service
Address
Purchased from:
Company name
City
State
Zip
■ less than 1
■ 1-3
■ 3-5
■ 5-10
Address
Purchase Date
City
State
Zip
Product Purchased
■ New installation
Type of Pool
Size of Pool
■ Inground
Please send me more information on these
other products from Sta-Rite.
■ Replacement
■ Vinyl
■ Fiberglass
■ Gunite
■ Pumps ■ Filters ■ Automatic Pool Cleaners
■ Maintenance Equipment ■ Test Strips
■ Heaters
S4877PS (Rev. 2/4/03)
16