TruVision Series 5 IP Camera Installation Guide

TruVision Series 5 IP
Camera Installation
Guide
P/N 1073339-EN • REV B • ISS 13SEP17
Copyright
© 2017 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls &
Security, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
Manufacturer
Trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance
FCC conditions
Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference.
(2) This Device must accept any interference
received, including interference that may cause
undesired operation.
ACMA compliance
Canada
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
This Class A digital apparatus complies with CAN
ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est
conforme à la norme CAN ICES-003 (A)/NMB-3
(A).
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the EMC
Directive 2014/30/EU, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
2013/56/EU & 2006/66/EC (battery directive):
This product contains a battery that cannot be
disposed of as unsorted municipal waste in the
European Union. See the product documentation
for specific battery information. The battery is
marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated
collection point. For more information see:
www.recyclethis.info.
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
Content
Introduction 2
Product overview 2
Installation 3
Installation environment 3
Package contents 4
Cable requirements 10
Camera description 11
Setting up the camera 13
IR illuminators 13
Accessing the SD card 14
Mounting the bullet camera 14
Mounting the turret camera 15
Mounting the dome camera 18
Using the camera with a TruVision recorder or another
system 22
Using the camera with TruVision Navigator 22
Specifications 22
TruVision IP bullet cameras 22
TruVision IP turret dome 23
TruVision IP dome cameras 23
Pin definitions 24
Installation Guide
1
Introduction
Product overview
This is the installation guide for TruVision Series 5 IP camera
models:

TVB-5501 (3MPX IP bullet camera)

TVB-5502 (8MPX IP bullet camera)

TVT-5501 (3MPX IP turret camera)

TVT-5502 (8MPX IP turret camera)

TVD-5501
(3MPX IP dome camera)

TVD-5502
(8MPX IP dome camera)
2
Installation Guide
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
•
Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
•
Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•
Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater
is between -30 to +60°C (-22 to 140°F). Humidity is below
90%. For the outdoor cameras that feature built-in
heaters, the operating temperature range is -40 to 60°C
(-40 to140°F)
•
Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
•
Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
Installation Guide
3
•
Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
IP bullet camera
•
Camera
•
12 VDC connector:
Two terminal
connector with positive
and negative
indicators.
•
Water joint: Provides
water resistance to
network cable connector.
•
Drill template
Ho
le
Ce
ilin
gM
o
un
tin
g
Ho
le
Ho
le
4
Installation Guide
•
Screws
•
CD with Configuration
manual and TruVision
Device Manager
Drywall anchor
7.5 × 24.5 mm (3 pcs)
Screw
M4 × 25 mm (3 pcs)
•
Installation manual
•
Equipment Disposal
Sheet
•
Battery Disposal Sheet
•
Torx wrench
Installation Guide
5
IP turret camera
•
Camera
•
12 VDC connector:
Two terminal connector
with positive and
negative indicators.
•
Camera drill template
•
Water joint: Provides
water resistance to
network cable
connector.
•
Screws
•
Adapter plate
Drywall anchor
7.5 × 24.5 mm (4 pcs)
Screw
M4 × 25 mm (4 pcs)
6
Installation Guide
•
CD with Configuration
manual and TruVision
Device Manager
•
Screw PM4 × 8 (3pcs)
•
Screw PM6-32 × 10
(4 pcs, used to attach
the turret camera to a 2
Gang electrical box)
•
Screw KM4 × 8 (4 pcs,
used to attach the
adapter to the
brackets)
•
Torx wrench
•
Installation manual
•
Installation manual of the
turret adapter
•
Equipment Disposal
sheet
Installation Guide
7
•
Battery Disposal Sheet
IP dome camera
•
Camera
•
12 VDC connector:
Two terminal connector
with positive and
negative indicators.
•
Camera drill template
•
Screws
Drywall anchor
7.5 × 24.5 mm (3 pcs)
Screw
M4 × 25 mm (3 pcs)
8
Installation Guide
•
Torx wrench
•
Water joint: Provides
water resistance to
network cable
connector.
•
Toggle bolt (3 pcs)
•
Gray cloth
•
CD with Configuration
manual and TruVision
Device Manager
•
Installation manual
Installation Guide
9
•
Equipment Disposal
sheet
•
Battery Disposal Sheet
Caution: Use direct plug-in UL listed power supplies marked
Class 2/CE certified or LPS (limited power source) of the
required output rating as listed on the unit.
Caution: Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
Cable requirements
For proper operation, adhere to the following cable and power
requirements for the cameras. Category 5 cabling or better is
recommended. All network cabling must be installed according
to applicable codes and regulations. Table 1 lists the
requirements for the cables that connect to the camera.
Table 1: Recommended power cable requirements
IP bullet camera:
12 VDC power wires or PoE (802.3af)
IP turret camera:
12 VDC power wires or PoE (802.3af)
IP dome camera:
12 VDC power wires or PoE (802.3af)
10
Installation Guide
Camera description
Figure 1: IP bullet camera
1.
Adjustable bracket
7.
12 VDC power
2.
Back housing
8.
Reset button
3.
Front housing
9.
SD card slot
4.
Lens
10. Grounding screw
5.
Sunshield
11. Serial port (factory use)
6.
Ethernet RJ45 PoE
port
Note: To reset the camera to default settings, press and hold
the RESET button and power on the camera. After the camera
has started up, hold the RESET button for an additional 20
seconds.
Installation Guide
11
Figure 2: IP turret camera
1.
Lens assembly
4.
Base
2.
Trim ring
5.
12 VDC power
3.
Housing
6.
Ethernet RJ45 PoE port
Figure 3: IP dome camera
1.
12 VDC power
5.
Base
2.
Audio I/O
6.
Dome liner
3.
Alarm I/O
7.
Lens
4.
Ethernet RJ45 PoE port
5.
Housing cover
12
Installation Guide
Setting up the camera
Note: If the light source where the camera is installed
experiences rapid, wide-variations in lighting, the camera may
not operate as intended.
To quickly put the camera into operation:
1.
Prepare the mounting surface.
2.
Mount the camera on the mounting surface using the
appropriate fasteners. See “Mounting the bullet camera”
on page 14.
3.
Set up the camera’s network and streaming parameters
so that the camera can be controlled over the network.
For further information, please refer to the “TruVision
Series 5 IP Camera Configuration Manual”.
4.
Program the camera as appropriate for its location. For
further information, please refer to the “TruVision Series 5
IP Camera Configuration Manual”.
IR illuminators
The camera’s built-in IR illumination provides high-quality
video in low-light environments, even when there is no other
illumination available.
You can configure the IR illumination using a web browser or a
client software, such as TruVision Navigator. If the function is
enabled, the IR light is On when the camera enters night
(black and white) mode. If disabled, the IR light is always Off.
The visible IR range may vary due to multiple factors such as
weather, IR reflection level of objects in frame, lens
adjustment, and camera settings. Please refer to the camera
datasheet for the standard IR range.
Installation Guide
13
Note: Avoid installing the IR camera closely facing a solid
object such as a tree or wall. The reflection will cause overexposure and loss of visibility of detail in field of view.
Accessing the SD card
Insert a Micro SD card with up to 128GB to use the camera as
an additional recording device, or as a backup in case of
failure of communication with the network video recorder (see
Figure 1 on page 11). The card is not supplied with the
camera.
Recorded video and log files can be accessed via the web
browser or via TruVision Navigator.
Mounting the bullet camera
Mount the camera on a ceiling or wall.
To mount the bullet camera:
1.
Use the supplied template to mark out the mounting area.
Drill the screw holes on the ceiling or wall. If you need to
route the cables from the camera base, drill a cable hole
in the ceiling or wall.
2.
Secure the mounting base to the ceiling or wall using the
three mounting screws and drywall anchors.
14
Installation Guide
3.
Loosen the large nut at the base of the mounting bracket
to adjust the camera’s viewing angle.
Pan direction: 0 to 360° adjustable
Tilt direction: 0 to 90° adjustable
Rotate direction: 0 to 360° adjustable
4.
Adjust the lens to the desired surveillance angle. Tighten
the adjustable nuts to complete the installation.
Mounting the turret camera
To mount the turret camera on a surface:
1.
Place the drill template (supplied) on the surface where
the camera is to be mounted. Drill mounting holes in the
surface using the holes labeled number “1” on the drill
template.
If you would like to route the cable harness through the
mounting surface, cut a cable access hole in the
mounting surface, referencing the letter “A” on the drill
template. Skip this step if you want to route the cables on
the surface.
Installation Guide
15
If installing the turret camera to a wall mount or other
accessory, an adapter plate is provided. Install the
adapter plate to the accessory with three PM4X8 screws,
referencing number “2”.
2.
Rotate the trim ring counterclockwise to remove it from
the camera.
3.
Route the cables directly out of the base of the camera.
4.
Install the camera on the mounting surface using the
supplied hardware.
5.
Connect the corresponding power and network cables.
6.
Adjust the lens.
a)
16
Loosen the locking screw using a Philips screw
driver.
Installation Guide
b)
Rotate the lens assembly to adjust the pan angle.
Rotate the lens assembly to adjust the tilt angle.
c)
Tighten the locking screw to secure the lens at the
desired surveillance angle.
Locking
screw
7.
Attach the trim ring to the camera and rotate it clockwise
to secure it.
Installation Guide
17
Mounting the dome camera
To mount the dome camera on a ceiling or wall:
1.
Place the drill template (supplied) on the surface where
the camera is to be mounted. Drill mounting holes in the
surface using the holes labeled number ‘1’ on the drill
template.
If you would like to route the cable harness through the
mounting surface, cut a cable access hole in the
mounting surface, referencing the letter “A” on the drill
template. Skip this step if you want to route the cables on
the surface.
2.
18
Using the supplied Torx wrench, remove the dome
bubble assembly.
Installation Guide
Screw
3.
Install the dome on the mounting surface using the
supplied hardware.
Installation Guide
19
4.
Loosen the tilt adjust screws (see image below) and
adjust the tilt position of the lens assembly within a range
of 75 degrees. Retighten the tilt adjust screws.
Rotate the dome liner to adjust the pan position within a
range of 355 degrees. Rotate the lens assembly (0 to
355°) to obtain the desired surveillance angle.
20
Installation Guide
5.
(Optional) If using a micro SD card (not included):
To remove the SD card, push the micro SD card forward.
The micro SD card will spring out.
SD slot
6.
Reinstall the dome housing and tighten the Torx screws.
Installation Guide
21
Using the camera with a TruVision
recorder or another system
Please refer to the NVR/DVR user manuals for instructions on
connecting and operating the camera with these systems.
Using the camera with TruVision
Navigator
A camera must be connected to an Interlogix NVR in order to
be operated by TruVision Navigator. Please refer to the
TruVision Navigator user manual for instructions on operating
the camera with TruVision Navigator.
Specifications
TruVision IP bullet cameras
Electrical
Voltage input
12 VDC, PoE (IEEE 802.3af)
Power consumption
3MPX: Max. 7 W
8MPX: Max. 7.5 W
Miscellaneous
Connectors
12 VDC Power Input, Network Port
(PoE)
Operating temperature
-30 to +60 °C (-22 to +140°F)
Dimensions
70 × 155.03 mm
(2.76 x 6.1 in.)
Weight
410 g (0.9 lbs.)
22
Installation Guide
Environmental rating
IP67
TruVision IP turret dome
Electrical
Voltage input
Power consumption
12 VDC, PoE (IEEE 802.3af)
3MPX: Max. 7 W
8MPX: Max. 7 W
Miscellaneous
Connectors
12 VDC Power Input, Network Port
(PoE)
Operating temperature
-30 to +60 °C (-22 to +140 °F)
Dimensions
127.3 × 95.9 mm
(5.01 × 3.78 in.)
Weight
620 g (1.37 lbs.)
Environmental rating
IP67
TruVision IP dome cameras
Electrical
Voltage input
Power consumption
12 VDC, PoE (IEEE 802.3af)
3MPX: Max. 7W
8MPX: Max. 9W
Miscellaneous
Connectors
Network Port(PoE), Audio In/Out,
Alarm In/Out, 12 VDC Power Port
Operating temperature
-30 to +60 °C (-22 to 140°F)
Installation Guide
23
Dimensions
111 × 82.4 mm
Weight
500 g (1.1 lbs.)
Environmental rating
IP67, IK10
(4.4 × 3.2 in.)
Pin definitions
There are eight wires on a standard UTP/STP cable and each
wire is color-coded. The following shows the pin allocation and
color of straight and crossover cable connection:
Figure 4: Straight-through cable
1
White/Orange
2
Orange
3
White-Green
4
Blue
5
White/Blue
6
Green
7
White/Brown
8
Brown
24
White/Orange
1
Orange
2
White-Green
3
Blue
4
White/Blue
5
Green
6
White/Brown
7
Brown
8
Installation Guide
Figure 5: Cross-over cable
1
White/Orange
2
Orange
3
White-Green
4
Blue
5
White/Blue
6
Green
7
White/Brown
8
Brown
White/Orange
1
Orange
2
White-Green
3
Blue
4
White/Blue
5
Green
6
White/Brown
7
Brown
8
Please make sure your connected cables have the same pin
assignment and color as above before deploying the cables in
your network.
Installation Guide
25