バイクポッド AD262 取扱説明書

Add to my manuals
2 Pages

advertisement

バイクポッド AD262 取扱説明書 | Manualzz

NOTE Do not stretch the elastic connection cord over 10cm

(4 inches). Excessively stretching may break the electronic circuitry of the bike pod.

Bluetooth Smart Bike Pod

Model: AD262

User Manual

The AD262 bike pod is equipped with the latest Bluetooth

Smart technology to achieve reliable transmission linkage with sports system device that is with the logo corresponding application.

SMART READY and

EN

PACKAGE ITEMS

The package should include the following items:

1 x AD262 bike pod

(1 x Silicon rubber cushion and

1 x CR2032 3V lithium battery installed)

1 x Cadence magnet 1 x Speed magnet 4 x Nylon cable ties

OVERVIEW

BIKE POD

Cadence sensor

Connection cord

Speed sensor

Silicon rubber cushion

CADENCE SENSOR

Cable tie hole

Alignment notch

Battery compartment

Magnet

SPEED SENSOR

Screw

Bicycle fork hole

Magnet

INSTALLING THE BIKE POD

MAGNET & SPEED SENSOR

1. Unscrew magnet and press slot onto spoke.

2. Tighten the screw with a screwdriver. Make sure the flat magnet surface facing the speed sensor.

3. Position speed sensor onto the top of bicycle chain stay. Using alignment notch as a guide to adjust the sensor and the magnet, so the magnet passes the sensor at the correct position.

4. Thread a nylon cable tie through each of the holes on the sensor.

Loop cable tie around the bicycle chain stay, then thread the end through the opening and past the ratchet. Pull to secure into place.

TIPS Cut away unnecessary cable tie to avoid it being caught in the wheel while in motion.

NOTE Improper alignment may affect speed sensor’s performance.

MAGNET & CADENCE SENSOR

1. Choose the crank arm which is not on the same side as the chain ring. Place magnet (with plastic base) onto the crank arm of the pedal, making sure the magnet faces the chain ring.

2. Thread a nylon cable tie through the hole on the magnet. Loop cable tie around the crank arm then thread the end through the opening and past the ratchet.

Pull to secure into place.

3. Position the cadence sensor on the bicycle chain stay. Align it with the magnet’s path. Adjust the position by stretching the elastic connection cord.

4. Using a nylon cable tie on the cadence sensor. Loop cable tie around the chain stay then thread the end through the opening and past the ratchet. Pull to secure into place.

TIPS Cut away unnecessary cable tie to avoid it being caught in the wheel while in motion.

NOTE Improper alignment may affect cadence sensor’s performance.

PAIRING DEVICE

The AD262 bike pod can be paired with your Bluetooth Smart sports system device to provide speed / cadence readings.

The bike pod has a maximum transmission range of about

100 centimeters (40 inches).

To pair with Oregon Scientific Bluetooth Smart device (such as SE900 or RA900 Ssmart Watch), please refer to the particular pairing instructions in the User Manual.

PAIR WITH OREGON SCIENTIFIC

BLUETOOTH SMART SPORTS SYSTEM DEVICE

NOTE While pairing, make sure to stay away from other devices and move the bike pod to pair close to your main device.

NOTE If pairing is weak and unstable:

• Shorten the distance between the bike pod and your sports device.

• Re-adjust the position of the device.

• Check the battery. Make replacement when necessary.

If the sports device is already paired with a bike pod, you have to first delete the bike pod before you are able to pair with another bike pod.

INPUT BIKE WHEEL SIZE

If your device is paired with this bike pod, the device will prompt you to input the wheel size values.

ETRTO

25-559

23-571

35-559

37-622

47-559

20-622

52-559

23-622

25-622

28-622

32-622

42-622

47-622

USEFUL REFERENCE

About Bike Wheel Size

Match the ETRTO or wheel size diameter printed on the wheel with the wheel size setting at the right hand column of the table below. Input the relevant wheel size setting number after bike pod is paired.

Wheel size diameter (inches)

26 x 1.0

650 x 23C

26 x 1.50

700 x 35C

26 x 1.95

700 x 20C

26 x 2.0

700 x 23C

700 x 25C

700 x 28

700 x 32C

700 x 40C

700 x 47C

Wheel size setting (mm)

1884

1909

1947

1958

2022

2051

2054

2070

2080

2101

2126

2189

2220

NOTE Wheel sizes on this table are for reference only as wheel size depends on the wheel type and air pressure.

REMOVE PAIRED DEVICE

To remove the bike pod from your device, please refer to the particular pairing instructions in the User Manual.

REPLACE BATTERY

Please replace battery promptly as it may affect the accuracy of the readings.

To replace the sensor battery:

1. Use a coin to open the battery compartment lid by turning it anticlockwise.

2. Remove the old battery and insert a new

CR2032, 3V lithium battery. Make sure to place the battery in the compartment following the polarity +/-.

3. Secure the lid by turning the coin clockwise.

IMPORTANT Remember to pair device after every battery replacement or reset.

CARE INSTRUCTIONS

• Do not wrap the sensor in a wet towel nor with other wet materials.

• Do not place or wash the sensor under running water, instead clean it with a wet cloth.

• Do not store the sensor in a hot (about 50°C) and humid

(about 90%) environment.

WATER RESISTANCE

The AD262 is water-resistant up to 10 meters (32.8 feet).

NOTE Ensure the battery compartment is secured and intact before exposing to excessive water.

SPECIFICATIONS

Power 1 x CR2032 3V lithium battery

Operating temperature 5˚C to 40˚C (41˚F to 104˚F)

Storage temperature -20˚C to 60˚C (-4˚F to 140˚F)

PRECAUTIONS

To ensure you use your product correctly and safely, read these warnings and the entire user manual before using the product:

• Use a soft, slightly moistened cloth. Do not use abrasive or corrosive cleaning agents, as these may cause damage. Never use the products in hot water or store them when wet.

• Do not subject the product to excessive force, shock, dust, temperature changes, or humidity. Never expose the product to direct sunlight for extended periods. Such treatment may result in malfunction.

• Do not tamper with the internal components. Doing so will terminate the product warranty and may cause damage.

The main unit contains no user-serviceable parts.

• Take precautions when handling all battery types.

• Remove the battery whenever you are planning to store the product for a long period of time.

• When replacing battery, use new battery as specified in this user manual.

• The product is a precision instrument. Never attempt to take this device apart. Contact the retailer or our customer service department if the product requires servicing.

• Do not touch the exposed electronic circuitry, as there is a danger of electric shock.

• Check all major functions if the device has not been used for a long time. Maintain regular internal testing and cleaning of your device. Have your watch serviced by an approved service center annually.

• When disposing of this product, ensure it is collected separately for special treatment and not as normal household waste.

• Due to printing limitations, the displays shown in this manual may differ from the actual display.

• The contents of this manual may not be reproduced without the permission of the manufacturer.

NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice.

NOTE Features and accessories will not be available in all countries. For more information, please contact your local retailer.

ABOUT OREGON SCIENTIFIC

Visit our website www.oregonscientific.com to learn more about Oregon Scientific products.

For any enquiry, please contact our Customer Services at info@oregonscientific.com.

EU-DECLARATION OF CONFORMITY

Hereby, Oregon Scientific, declares that Bluetooth Smart

Bike Pod (model: AD262) is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC. A copy of the signed and dated Declaration of

Conformity is available on request via our Oregon Scientific

Customer Service.

COUNTRIES RTTE APPROVED COMPLIED

All EU countries, Switzerland CH

and Norway N

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for support or sales. Please visit our website at www.oregonscientific.com for all enquiries.

We

Name:

Address:

Telephone No.:

Oregon Scientific, Inc.

19861 SW 95th Ave.,Tualatin,

Oregon 97062 USA

1-800-853-8883 declare that the product

Product No.: AD262

Product Name:

Manufacturer:

Address:

Bluetooth Smart Bike Pod

IDT Technology Limited

Block C, 9/F, Kaiser Estate,

Phase 1, 41 Man Yue St.,

Hung Hom, Kowloon,

Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.

Bluetooth バイクポッド

モデル: AD262

取扱説明書

AD262 バイクポッドは、最新のBluetooth Smart テクノロ

ジーを搭載し、

SMART READY

のロゴがあり、関連アプリがダウ

ンロードされたスポーツデバイスと通信することができま

す。対応機種につきましては、ホームページ上で公開して

おりますのでご確認ください。

JAP

製品内容

以下のアイテムが同梱されています。

AD262 バイクポッドx1個

(シリコンゴムクッションx1個 と

CR2032 3V リチウム電池1個を含みます。)

ケーデンスセンサー用磁石 x1個 スピードセンサー用磁石x 1個 ナイロンケーブルタイx4個

概要

バイクポッド

ケーデンスセンサー

接続コード

スピードセンサー

シリコンゴムクッション

ケーデンスセンサー

ケーブルタイホール

アライメントノッチ

電池蓋

磁石

スピードセンサー

ネジ

バイクフォーク穴

磁石

バイクポットの装着

磁石&スピードセンサー

1. ネ ジ を 外 し て 磁 石 を 取 り出

し、スポークにはめ込んでく

ださい。

2. ネジをドライバーで締めてく

ださい。磁石の表面がスピー

ドセンサーに面しているかを

確認してください。

3. スピードセンサーをバイクの

チェーンステーの上に据え付

けます(図参照)。アライメント

ノッチをガイドとして使い、

センサーと磁石の位置を調整

してください。そうすること

により、磁石がセンサーに反

応する場所を通過することが

できます。

4. ナ イ ロ ン ケ ー ブ ル タ イ をセ

ンサーの各穴に通してくださ

い。ケーブルタイをバイクの

チェーンステーに通し、回し

て、反対側の穴に通して引いて固定してください。

備考 必要の無いタイケーブルは絡まる可能性があります

ので、切り落としてください。

注意 不適切な据え付けは、測定精度に影響を与える可能性が

あります。

磁石とケーデンスセンサー

1. チェーンリングと同じ側でないクランクアームを選択

します。磁石(プラスチックケース付属)がチェーンリ

ングに面する様にペダルのク

ランクアームの上に置いてく

ださい。

2. ナ イ ロ ン ケ ー ブ ル タ イ をセ

ンサーの各穴に通してくださ

い。ケーブルタイをバイクの

チェーンステーに通し、回し

て、反対側の穴に通して引い

て固定してください。

3. ケーデンスセンサーをバイク

チェーンステーに据え付け、

伸縮性のある接続コードで、

磁石通るところに合わせてく

ださい。

4. ナ イ ロ ン ケ ー ブ ル タ イ をセ

ンサーの各穴に通してくださ

い。ケーブルをバイクのチェ

ーンステーに通し、回して、

反対側の穴に通して引いて固

定してください。

備考 必要の無いタイケーブルは絡まる可能性があります

ので、切り落としてください。

注意 不適切な据え付けは、測定精度に影響を与える可能性

があります。

注意 伸縮性のある接続コードは、10cm以上引っ張らない

でください。過剰な伸長は、バイクポッドの電気回路に障害

を生じる可能性があります。

デバイスのペアリング

AD262 は、Blue tooth smart spoorts systemデバイスとペア

リングができ、スピードとケーデンスの測定ができます。

バイクポッドの最大の通信距離は100cmです。オレゴンサ

イエンティフィックのBluetooth smart 機器と接続する場合

は、機器のペアリング方法に従ってください。(説明書はホ

ームページからダウンロードできます。)その他機器と接続

する場合は、その機器の説明書に従ってください。

Ssmart watchホームページ http://ssmart.oregonscientific.com/Japan/

以下のQRコードからもアクセスできます。

オレゴンサイエンティフィックSSMART WATCH

SE900/RA900 とのペアリングについて

注意 ペアリングを行う場合、他のデバイスを遠ざけ、ペア

リングをするデバイスとバイクポッドを近づけてください。

注意 信号が弱い場合

• バイクポッドとスポーツデバイスの距離を短くしてく

ださい。

• バイクポットの位置を再調整してみてください。

• 電池の残量を確認してください。電池の残量が少なく

なると通信距離が短くなります。

お使いのスポーツデバイスがすでに別のバイクポッドとペ

アリングされている場合は、まず、別のバイクポッドとの

ペアリングを削除してから、AD262とのペアリングを行っ

てください。

車輪のサイズの入力

バイクポッドとデバイスのペアリング時に、デバイスは車

輪のサイズの入力を促します。

25-559

23-571

35-559

37-622

47-559

20-622

52-559

23-622

25-622

28-622

32-622

42-622

47-622

参考

ETRTOに合わせるかもしくは車輪に記載されている、車輪

の直径サイズを右の表から選択し、適切な車輪サイズをバ

イクポッドのペアリング後、入力を行ってください。

ETRTO

車輪の直径サイ

ズ(インチ)

26 x 1

650 x 23C

26 x 1.50

700 x 35C

26 x 1.95

700 x 20C

26 x 2

700 x 23C

700 x 25C

700 x 28

700 x 32C

700 x 40C

700 x 47C

車輪サイズ設定

(mm)

1884

1909

1947

1958

2022

2051

2054

2070

2080

2101

2126

2189

2220

注意 車輪サイズは、車輪タイプや空気圧に影響を受けま

すので、表の車輪サイズは、参考のみとして頂きますよう

お願い致します。

ペアーデバイスの取り外し

バイクポッドを取り外すときには、取説のペアリングの項

目の説明を参照してください。

電池交換

電池寿命は、毎日1時間のご使用で15か月にな

ります。Low battery(ローバッテリー)の表示が

腕時計に現れたらAD262の電池を交換してくだ

さい。

1. 硬貨を使い、反時計周りに回し、電池蓋を開

けてください。

2. 古い電池を取り出して、新しいCR2032

3Vリチウム電池を元の電池の向きと同じよ

うに挿入してください。

3. 時計周りに蓋を回して蓋を閉めてくださ

い。

重要 電池交換後及びリセット後はペアリン

グを再度行ってください。

注意事項

• 濡れたタオルでチェストベルトを包まないで下さい。

• 高温高湿の場所では保管しないで下さい。

• 水道の水でチェストベルトを洗い流さないで下さい。汚

れは布でふき取ってください。

• チェストベルトを高温(約50°C)、高湿(約90%)の環境に

置かないでください。

防水性

AD262は、生活防水対応です。

注意 防水性を有効にするために、蓋がしっかり締まって

いるか、また、本体が破損していないか確認を行ってくだ

さい。

仕様

電源

使用温度

保存温度

リチウム電池

5°C to 40˚C

-20°C to 60˚C

注意事項

• 柔らかく、軽く湿った布を使用してください。

• 研磨性、腐食性のある洗剤で洗浄しないでください。

• 熱湯で本体を洗浄しないでください。

• 製品に過度の力、衝撃、ほこり、温度変化、湿度などを

与えないでください。また、直射日光の当たる場所に、

長時間、製品を置かないでください。故障や不具合の原

因になります。

• 製品の内部部品を改ざんしないでください。された場、

製品保証の対象にはなりません。

• 長期間使用しないときは、電池を取り外してください。

• 電池交換を行うときは、取説に基づいて新しい電池を使

用してください。

• 本製品は精密機器です。本体を分解しないでください。も

し何か対応が必要な場合、お買い上げの店舗かカスタマー

サポートまでご連絡を頂きますようお願い致します。

• 電気ショックの危険がありますので、むきだしの電子部品

には触らないでください。

• 長期間ご使用になられない場合、機能の確認を行ってくだ

さい。カスタマーサポートセンターでの定期的な検査をお

勧め致します。(有料)

• 本製品を廃棄する場合、普通ゴミの処理ではなく、電子機

器の廃棄に対応する廃棄処理を行ってくださ い。

• 本取扱説明書に記載している表記と実際の表記が異なる場

合があります。

• 本内容を許可なく転記することを禁止します。

注意 本製品の技術仕様、取説の内容は事前の通告無しに

変更することがあります。

注意 機能やアクセサリーはすべての国で適応されるもの

ではありません。

当社サービスセンター

保土ヶ谷電子販売株式会社

〒104-0041

東京都中央区新富1-13-21

TEL0120-11-4820

(土日を除く、平日10:00 12:00/13:00 17:00)

日本国内電波法適合

日本国内向けのAD202には、日本国内の電波法認証を受

け、認証番号が印刷されています。正規輸入品でない、

AD262は、国内の法律には準拠していません。

製品保証

• 製品保証期間は、製品をご購入後1年間です。

• 保証期間内の修理対応には、販売店での領収書が必要とな

ります。領収書がない場合は、保証の対象となりませんの

で保証書は大切に保管してください。

• 正規販売店以外の店舗、平行輸入品、転売品は保証の対象

外となります。

• 正常な使用を重ねるうちに生じる傷、摩耗は保証対象外と

なります。

• 故意、過失、誤用などによる不良は保証対象外となります。

• 本製品の使用、また使用不能から発生する、付随的な損

害(機械利益損失を含む)に関しては、一切責任を負いま

せん。

• 製品を返送いただく際の送料負担は、お客様の負担となり

ますことをあらかじめご了承ください。

© 2013 Oregon Scientific. All rights reserved.

P/N:300103257-0000x-10

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement