Instructions
120-BV2-TNCH-AD-Z – Chrome
120-BV2-TNBN-AD-Z – PVD Brushed Nickel
Certifications
Two Handle Roman Tub Faucet
Must be used with 900-RTAD Roman tub rough-in.
*Image may vary slightly from actual product
Tools Required
Maintenance
Adjustable Wrench
Groove Joint Pliers
Pipe Wrench
Phillips Screwdriver
Pipe Tape or pipe thread compound
Your new Roman tub faucet is designed for years of trouble-free
performance.
Safety Tips
If you solder the joints during installation of the faucet, the seats,
cartridges, and washers must be removed before using a flame
or the warranty will be voided on these parts.
Protect your eyes with safety glasses when cutting or soldering
water supply lines.
Cover the sink drain to avoid losing parts.
Things You May Need
Installations may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of your faucet are
not all included; however, they are available wherever plumbing
supplies are sold.
Keep it looking new by cleaning it periodically with a soft cloth.
Avoid abrasive cleaners, steel wool, and harsh chemicals as
these will dull the finish and void your warranty.
Important Points
Prior to beginning installation, turn off the hot and cold water
lines, then turn on the old faucet to release built-up pressure.
When installing your new faucet, turn the connector nuts finger
tight, then use one wrench to hold the fitting and a second
wrench to tighten the nut. Connections that are too tight will
reduce the integrity of the system.
Wrap all threaded connections with PTFE pipe tape available
at your local hardware or plumbing supply store. Always wrap
in a clock-wise direction.
Contact Us
For Customer Service please call 877-319-3757, or go to
homewerksww.com.
www.homewerksww.com
Effective/Rev Date: March 15, 2011
1
Instructions
120-BV2-TNCH-AD-Z – Chrome
120-BV2-TNBN-AD-Z – PVD Brushed Nickel
Certifications
Two Handle Roman Tub Faucet
Preparation and Assembly
1
Locate water supply inlet and shut off water supply valve. These are usually
found under the sink or near the water heater. Remove old faucet. Clean and
dry sink surface area where new faucet will be mounted.
3
Place handle flange (2A) onto body flange (2B) in desired position, then place
handle seat (2C) onto the valve stem (2D). Place handle (2E) onto seat (2C), then
place screw (2F) through the socket on top of the handle and thread until handle
is securely tight. Attach index (2G) onto the lever socket. Place the other handle
assembly onto the other valve stem and install the same way.
2
Take off the lid of the body assembly & lid of long shank.
4
Place spout assembly (3B) onto shank (3A) in desired position, then
place set screw (3C) through the socket towards the spout assembly
and thread until spout is securely tight.
5
Turn on water supply. Be sure to allow water to run into tub while checking
for leaks. This will allow air to escape that may have developed during
installation.
www.homewerksww.com
Effective/Rev Date: March 15, 2011
2
Troubleshooting
120-BV2-TNCH-AD-Z – Chrome
120-BV2-TNBN-AD-Z – PVD Brushed Nickel
Certifications
Two Handle Roman Tub Faucet
Troubleshooting
PROBLEM: Leaks underneath handle.
CAUSE: Bonnet has come loose or O-ring on cartridge is dirty or twisted.
ACTION:
1. Move the handle to the off position. Remove index button. Unscrew
the handle screw and remove the handle (Diagram A).
2. Tighten the bonnet by turning it clockwise (Diagram B). Move the
cartridge stem to the on position. The leak should stop draining out
from around the cartridge stem.
3. If the leak does not stop,shut off the water supply. Remove the bonnet
by turning it counter-clockwise. Lift out the cartridge valve (Diagram
C). lnspect the larger O-ring on the cartridge bonnet and the smaller
O-ring on the cartridge stem. Remove any debris from the O-rings. If
either O-ring is twisted, straighten it out. lf either O-ring is damaged,
replace the cartridge by calling customer service.
4. Position the cartridge back into the faucet body (Diagram D). Make
sure the ridges on the two sides of the cartridge bonnet fit into the
grooves on the two sides of the faucet body. Tightly screw the bonnet
onto the faucet body.
5. Re-install the handle.
PROBLEM : Water does not completely shut off.
CAUSE: Rubber valve seat is dirty,stuck,or broken.
ACTION:
1. Shut off the cold water supply. If leak stops, the problem is on the cold
side. If leak continues, the problem is on the hot side. Shut off the hot
water supply to determine if both the cold and hot sides have a
problem.
2. Remove the handle on the problem side. Loosen the bonnet by
turning it counter-clockwise (Diagram E). Lift out the cartridge
assembly.
3. Inspect the rubber valve seat in the faucet body. If there is debris or
brass scrap on the surface of the seat, remove it. If the rubber seat is
stuck tightly in the water inlet hole, push it gently with a fingertip so
that it moves up and down smoothly. If the rubber valve seat is worn
out or broken, replace the cartridge by calling customer service.
4. Replace the cartridge into the faucet body. Make sure that the ridges
on the two sides of the cartridge bonnet fit into the grooves on the
two sides of the faucet body (Diagram F). Tightly screw the bonnet
onto the faucet body.
5. Re-install the handle.
A
B
C
D
E
F
www.homewerksww.com
Effective/Rev Date: March 15, 2011
3
Specifications
Certifications
Physical Characteristics
•
•
•
•
•
•
•
No.
1
2
3A
3B
4
5A
5B
6
7
8
9
10
11
12
13
14
www.homewerksww.com
Description: 2 handle Roman tub faucet with 6" - 12" center
distance, brass waterways and ceramic cartridges
Trim only
Roman tub filler
Solid brass spout
Max. Flow Rate: 2.2 GPM (8.3 LPM)
3-hole installation
ASME A112.18.1/CSA B125 certified
Part Description
Flange
Handle seat
Handle - hot
Handle - cold
Screw
Index - hot
Index - cold
Ornate cap
Screw
Spout
O-ring
Set screw
Connector
Spout seat
Washer
Aerator
120-BV2-TNCH-AD-Z – Chrome
120-BV2-TNBN-AD-Z – PVD
Brushed Nickel
Material
Brass C37700
Brass C37700
ZZnA14
ZZnA14
SUS304
ABS
ABS
Brass C37700
SUS304
Brass C37700
EPDM
SUS304
Brass C37700
Brass C37700
Steel Q235A
POM
Effective/Rev Date: March 15, 2011
4
Rough-In
120-BV2-TNCH-AD-Z – Chrome
120-BV2-TNBN-AD-Z – PVD Brushed Nickel
Certifications
Two Handle Roman Tub Faucet
www.homewerksww.com
Effective/Rev Date: March 15, 2011
5
Download PDF
Similar pages
Douos SPECIFICATIONS
Beemlen SPECIFICATIONS
Amity SPECIFICATIONS
Eclipse SPECIFICATIONS
KitchenAid KKFV01LPSS User's Manual
Melik SPECIFICATIONS
Conifer SPECIFICATIONS