TE 706 / TE 706-AVR

TE 706 /
TE 706-AVR
Bedienungsanleitung
de
Operating instructions
en
Mode d’emploi
fr
Ръководство за обслужване
bg
Upute za uporabu
hr
Instrukcja obsługi
pl
Инструкция по зксплуатации
ru
Návod na obsluhu
sk
Navodila za uporabo
sl
Návod k obsluze
cs
Használati utasítás
hu
Instrucţiuni de utilizare
ro
zh
ja
ko
cn
IНСТРУКЦIЯ З ЕКСПЛУАТАЦIЇ
uk
ar
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
1
3
2
4
1
7
6
5
10
9
8
11
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
2
3
1
3
1
2,4
2
4
5
6
1
5
1
4
10
3
2
8
9
3
2
7
6
7
1
2
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
ORIGINAL OPERATING INSTRUCTIONS
TE 706/TE 706-AVR breaker
It is essential that the operating instructions
are read before the tool is operated for the
first time.
1. General information
en
1.1 Safety notices and their meaning
Always keep these operating instructions
together with the tool.
-CAUTIONDraws attention to a potentially dangerous situation that
could lead to minor personal injury or damage to the
equipment or other property.
Ensure that the operating instructions are
with the tool when it is given to other
persons.
-NOTEDraws attention to instructions and other useful information.
1.2 Pictograms
Warning signs
Operating controls and parts Chuck
Chisel adjustment and locking switch
On/off switch
Grip
Supply cord
Screw knob
Side handle
Lock symbol
Power level selection switch
Theft protection indicator (option)
Service indicator
Contents
1. General information
2. Description
3. Tools and accessories
4. Technical data
5. Safety rules
6. Before use
7. Operation
8. Care and maintenance
9. Troubleshooting
10. Disposal
11. Manufacturer’s warranty – tools
12. EC declaration of conformity (original)
General
warning
Warning:
electricity
Warning:
hot surface
Symbols
Read the
operating
instructions
before use.
Page
11
12
12
13
14
16
16
17
18
19
19
20
Equipped with
theft protection
system
Locksymbol
Return waste
material for
recycling
These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the operating instructions.
In these operating instructions, the TE 706 and / or
TE 706-AVR breaker is referred to as “ the power tool ”.
Location of identification data on the power tool.
The type designation can be found on the rating plate
and the serial number on the side of the motor housing.
Make a note of this data in your operating instructions
and always refer to it when making an enquiry to your
Hilti representative or service department.
Type:
Serial No.:
11
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
2. Description
en
2.1 Use of the power tool as intended
The power tool is designed for medium-duty chiseling
work. It is suitable for breaking/removing and demolishing concrete, masonry, stone or asphalt. It is intended
for use on construction sites of all kinds.
The power tool may be operated only when connected
to a power supply providing a voltage and frequency in
compliance with the information given on its rating plate.
Changes or modifications to the power tool are not permissible.
2.2 Important features of the power tool
2.2.1 Active vibration reduction
The TE 706-AVR is equipped with an active vibration
reduction system which cuts vibration to 40 % of that
of the TE 706 (without Active Vibration Reduction).
●
2.2.2 Theft protection system (option)
The power tool may be equipped with the optional
theft protection system. If the power tool is equipped
with this feature, it can be activated and made ready
for operation only by way of the corresponding activation key.
●
2.2.3 Chuck
● TE-Y (SDSmax) quick-change chuck
2.2.4 Switch
On/off switch
3-position power level selection switch (100 %, 75 %,
50 %)
● Chisel adjustment and locking switch (for 24 clickstop positions per revolution)
●
●
2.2.5 Grip (with soft synthetic rubber padding)
Two-way adjustable (pivoting) and vibration-absorbing side handle
● Vibration absorbing grip
●
2.2.6 Safety features
Electronic interlock to prevent unintentional restarting after interruption of the power supply (see section 9.).
● Casing and grip isolated from interior parts of the tool
to reduce transmission of heat and vibration.
● Automatic electronic overheating and overvoltage cutout (see section 9.).
●
2.2.7 Lubrication
Permanent lubrication with separate lubrication chambers for the gearing section and hammering mechanism.
●
2.2.8 Indicator lamps
Service indicator lamp (red, see section 8.3).
Theft protection system indicator (available as an
option) (yellow, see section 7.2.1).
●
●
2.2.9 Items supplied as standard
Power tool
Side handle
Grease dispenser, 50 ml
Cleaning cloth
Operating instructions
Toolbox with overview of insert tools.
●
●
●
●
●
●
3. Tools and accessories
TE 706/TE 706-AVR
TE-Y chuck (SDSmax)
Pointed chisel
Flat chisel
Wide-flat chisel
Hollow chisel
Channel chisel
Mortar chisel
Flexible chisel
Bushing tool
Tamping tool
Earth rod rammer
TPS Theft Protection System with Company
Card, Company Remote and TPS-K activation key
Width (mm)
Length (mm) Width (in)
Length (in)
––
26
50–120
28
22–36
38
150
40 x 40
150 x 150
∅ 15–25
option
280–700
280–700
280–500
280
280
280
650
250
300
300
11″–27″
11″–27″
11″–19″
11″
11″
11″
251/2″
10″
––
––
––
3/4″
2″–41/2″
1″
7/8″–11/2″
15/16″
57/8″
57/8″
––
––
Use the Hilti tools listed above. With these tools you will achieve a higher breaking and material removal
performance and longer service life as the power tool and the insert tool have been optimized as a system.
12
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
4. Technical data
Power tool
Rated power input
Rated voltage
Rated current
Mains frequency
Weight as per EPTA-Procedure
01/2003
Dimensions (L × W × H)
Chuck
Hammering speed under load
Single impact energy
Chiseling performance in
medium-hard concrete
Double insulated (in accordance
with EN 60745)
TE 706 / TE 706-AVR
1200 W 1200 W 1180 W 1180 W
120 V
127 V
100 V
110 V
9.9 A
9.3 A
12.3 A
11.1 A
50–60 Hz
1200 W
220 V
9.0 A
1200 W
230 V
8.7 A
1200 W
240 V
8.6 A
en
7.9 kg
560 × 125 × 250 mm
TE-Y (SDSmax)
2760 blows/min
6–10 joules
750 cm3/min
Protection class II Z
-NOTEThe vibration emission level given in this information sheet has been measured in accordance with a standardised
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure. The declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over the total working period. An estimation of the
level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working
period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain
the tool and the accessories, keep the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted sound power level:
TE 706
101 dB (A)
TE 706-AVR
98 dB (A)
Typical A-weighted sound pressure level:
TE 706
90 dB (A)
TE 706-AVR
87 dB (A)
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
Triaxial vibration value (vibration vector sum)
measured in accordance with EN 60745-2-6
Chiselling, (ah, Cheq):
TE 706
9.0 m/s2
TE 706-AVR
5.5 m/s2
Uncertainty (K) for triaxial vibration value
1.5 m/s2
Right of technical changes reserved.
13
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
5. Safety rules
en
NOTE
The safety rules in section 5.1 contain all general safety rules for
power tools which, in accordance with the applicable standards,
require to be listed in the operating instructions. Accordingly, some
of the rules listed may not be relevant to this tool.
5.1 General Power Tool Safety Warnings
a)
WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury. Save all warnings
and instructions for future reference. The term “power tool”
in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
5.1.1 Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
5.1.2 Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
5.1.3 Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while
you are tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
14
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
c) Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dustrelated hazards.
5.1.4 Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could
result in a hazardous situation.
5.1.5 Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
5.2 Safety precautions for chisels
a) Wear ear protection. Excessive noise may lead to a
loss of hearing.
b) Use the auxiliary handle supplied with the tool. Loss
of control of the tool may lead to injury.
c) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give
the operator an electric shock.
5.3 Additional safety precautions
5.3.1 Personal safety
a) Breathing protection must be worn when the tool is
used without a dust removal system.
b) Exercise your fingers during pauses between work
to improve the blood circulation in your fingers.
c) To avoid tripping and falling when working, always
lead the sypply cord, extension cord and dust extraction hose away tho the rear.
d) The tool is not intended for use by children, by debilitated persons or those who have received no instruction or training.
e) Children must be instructed not to play with the tool.
f) Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful.
Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders. Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.
Where the use of a dust extraction device is possible it shall be used. To achieve a high level of dust
collection, use a suitable vacuum cleaner of the type
recommended by Hilti for wood dust and/or mineral
dust together with this tool. Ensure that the workplace is well ventilated. The use of a dust mask of
filter class P2 is recommended. Follow national
requirements for the materials you want to work with.
c) Dirty or dusty electric tools should thus be checked
at a Hilti service center at regular intervals, especially if used frequently for working on conductive
materials. Dust (especially dust from conductive
materials) or dampness adhering to the surface of
the tool may, under unfavorable conditions, present
a risk of electric shock.
5.3.3 Power tool use and care
a) Ensure that the insert tools used are equipped with
the appropriate connection end system and that they
are properly fitted and secured in the chuck.
b) In the event of a power faillure, switch the tool off
and unplug the supply cord. This prevents inadvertent starting when the power returns.
c) Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with
a “live” wire will make exposed metal parts of the tool
“live” and shock the operator.
5.3.4 Work area
a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ventilated.Poorly
ventilated workplaces may be injurious to the health
due to exposeure to dust.
5.3.5 Personal protective equipment
The user and any other persons in the vicinity must
wear suitable eye protection, a hard hat, ear protection
and protective gloves when the tool is in use. Breathing protection must be worn if no dust removal system is used.
Wear eye
protection
Wear a
hard hat
Wear ear
protection
Wear
protective
gloves
Wear
breathing
protection
5.3.2 Electrical safety
a) Before beginning work, check the working area (e.g.
with a metal detector) to ensure that no concealed
electric cables or gas and water pipes are present.
External metal parts of the tool may become live if,
for example, an electric cable is damaged inadvertenly.
This presents a serious risk of electric shock.
b) Check the condition of the supply cord and its plug
connections and have it replaced by a qualified electrician if damage is found. Check the condition of
the extension cord and replace it if damage is found.
Do not touch the supply in the event of it suffering
damage while working. Disconnect the supply cord
plug from the socket. Damaged supply cords and
extension cords present a risk of electric shock.
15
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
en
6. Before use
en
Ensure that the tool is not yet connected to the electric
supply.
6.1 Fitting the side handle 1. Position the side handle on the tool.
2. Secure the side handle by tightening the screw knob.
6.2 Use of extension cords
Use only extension cords of a type approved for the
application and with conductors of adequate cross section.
6.3 Use of a generator or transformer
This tool may be powered by a generator or transformer
which fulfils the following conditions:
– AC voltage output, power output at least 2600 W.
– The operating voltage must be within +5 % and –
15 % of the rated voltage at all times.
– Frequency range 50–60 Hz, never above 65 Hz.
– Automatic voltage regulation with starting boost.
Never operate other tools or appliances from the generator or transformer at the same time. Switching other
tools or appliances on and off can cause undervoltage
and/or overvoltage peaks which may cause damage to
the power tool.
Recommended minimum conductor cross section and
max. cable lengths:
Mains voltage
100 V
110–127 V
220–240 V
Conductor cross section
1.5 mm2 2.0 mm2 2.5 mm2
–
20 m
–
20 m
25 m
30 m
50 m
–
100 m
3.5 mm2
30 m
–
–
AWG
14
–
75 ft
–
12
–
125 ft
–
Do not use extension cords with 1.25 mm2 or 16 AWG
conductor cross sections.
7. Operation
7.1 Preparation for operation
7.1.1 Adjusting the position of the side handle 1. Unplug the supply cord form the power source.
2. Release the screw knob on the side handle.
3. Bring the side handle into the desired position.
4. Secure the side handle in the desired position by
tightening the screw knob.
7.1.2 Fitting the insert tool 1. Unplug the supply cord form the power source.
2. Check that the connection end of the insert tool is
clean and lightly greased. Clean it and grease it if
necessary.
3. Check that the sealing lip of the dust shield is clean
and in good condition. Clean the dust shield if necessary or replace it if the sealing lip is damaged.
(See section 8.)
4. Push the insert tool into the chuck and rotate it
while applying slight pressure until it engages in
the guide grooves.
5. Push the insert tool further into the chuck until it
is heard to engage.
6. Check that the insert tool has engaged correctly by
pulling on it.
16
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
7.1.2.1 Positioning the insert tool 7. Turn the chisel adjustment and locking switch to the
"Rotate chisel" position.
8. Rotate the chisel to the desired position.
7.1.2.2 Locking the insert tool 9. Turn the chisel adjustment and locking switch to the
"Lock chisel" position.
10. Rotate the chisel until it engages (24 click-stop positions per revolution).
7.1.3 Removing the insert tool -CAUTION– The insert tool may become hot during use. There is
a risk of burning the hands. Wear protective gloves
when changing insert tools.1. Unplug the supply cord
form the power source.
2. Open the chuck by pulling back the chuck release
sleeve.
3. Pull the insert tool out of the chuck.
7.1.4 Setting the chiseling power level Chiseling power can be set to one of three positions
(50 %, 100 % und 75 %) by turning the power level selector switch.
7.2 Operation
7.2.1 Activating the power tool (theft protection
system) (Optional – not available with all versions.)
Further detailed information about activation and use of
this optional feature can be found in the separate operating instructions for the theft protection system.
1. Plug the supply cord into the power outlet. The yellow theft protection indicator lamp blinks. The power
tool is now ready to receive the signal from the activation key.
2. Hold the activation key close to the lock symbol. The
power tool is activated as soon as the theft protection
indicator lamp no longer lights.
-NOTEIn the event of interruption of the electric supply to the
power tool, e.g. brief disconnection to move to a different workplace, the power tool remains operational for
approx. 20 minutes. After a longer interruption, the power
tool must be reactivated by way of the activation key.
7.2.2 Chiseling
– The power tool and the chiseling operation emit noise.
Excessive noise may damage the hearing. Wear ear
protection.
– Chiseling may cause splintering of the material. Splinters may cause injury to parts of the body and eyes.
Wear eye protection, protective gloves and breathing protection if no dust removal system is used.
-NOTEWorking at low temperatures:
The hammering mechanism works only when the tool
has reached a minimum operating temperature.
Bring the drill bit into contact with the base material and
allow the tool to run under no load until the minimum
operating temperature is reached. If necessary, repeat
this procedure until the hammering mechanism begins
to operate.
7.2.2.1 Switching on
1. Plug the supply cord into the power outlet.
2. Press the on/off switch.
7.2.2.2 Switching off
1. Press the on/off switch.
8. Care and maintenance
Unplug the supply cord form the power source.
8.1 Care of insert tools
Clean off dirt and dust deposits adhering to the insert
tools and protect them from corrosion by wiping the
insert tools from time to time with an oil-soaked rag.
Hilti polygon chisels require no resharpening.
8.2 Care of the power tool
-CAUTIONKeep the power tool, especially its grip surfaces, clean
and free from oil and grease. Do not use cleaning agents
which contain silicone.
The outer casing of the tool is made from impactresistant plastic. Sections of the grip are made from a synthetic rubber material. Never operate the tool when the
ventilation slots are blocked. Clean the ventilation slots
carefully using a dry brush. Do not permit foreign objects
to enter the interior of the tool. Clean the outside of the
tool at regular intervals with a slightly damp cloth. Do not
use a spray, steam pressure cleaning equipment or running water for cleaning. This may negatively affect the
electrical safety of the tool.
8.3 Service indicator
The power tool is equipped with a service indicator.
8.3.1 The indicator lamp lights red
The power tool has been in use for a predetermined time
and now requires servicing.
After the lamp lights for the first time, the power tool
may continue to be used for approx. 10 days before the
automatic cut-out is activated. Bring the power tool to
a Hilti service center in good time so that the tool is
always ready for use when required.
8.3.2 The indicator lamp blinks red
A fault has occurred.
The power tool has been rendered inoperable. Return
the power tool to a Hilti service center for repair.
8.3.3 Protective cut-out
The power tool is equipped with an overheating prevention cut-out. This cut-out may be activated without
any warning. The cut-out may also be activated (or the
power tool may refuse to start), without the indicator
lighting, if a fault in the electric supply is detected (see
section 9).
8.4 Maintenance
Check all external parts of the tool for damage at regular intervals and check that all controls operate faultlessly. Do not operate the tool if parts are damaged or
when the controls do not function faultlessly. If necessary, your power tool should be repaired at a Hilti repair
center.
Repairs to the electrical section of the tool may be carried out only by trained electrical specialists.
17
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
en
9. Troubleshooting
Fault
The power tool doesn't
start.
en
Possible cause
The electronics are being initialized
(this takes up to approx. 4 seconds
after the supply cord is plugged in)
or the electronic cut-out has been
activated after an interruption in the
electric supply.
There is an interruption in the electric
supply.
The supply cord or plug is defective.
Generator with sleep mode.
The power tool doesn't
start and the indicator
lamp blinks yellow.
The power tool doesn't
start and the indicator
lamp blinks red.
The power tool doesn't
start or cuts out during
operation.
The power tool has not been activated
(tools with optional theft protection
system).
A fault has occurred in the tool.
Remedy
Switch the tool off and on again.
Check the electric supply, for example,
by plugging in and starting another
appliance.
Have the supply cord and plug checked
by an electrical specialist and replaced if
necessary.
Apply a load to the generator by connecting another appliance (e.g. a lamp) and
then switch the power tool off and on
again.
Use the activation key to activate the
power tool.
The power tool should be repaired at a
Hilti service center.
Allow the tool to cool down. Clean the
ventilation slots (see section 8.2).
Disconnect other appliances connected
to the same power source or connect the
power tool to a different power source.
Use an extension cord of permissible
The extension cord is too long or has
length and of adequate cross section
an inadequate cross section.
(see 6.2).
Allow the tool to warm up to the minimum
The power tool is too cold.
No hammering action.
operating temperature (see 7.2.2).
The power tool should be repaired at a
A fault has occurred in the tool.
Hilti service center.
The tool does not achieve The power level selector switch is not Bring the power level selector switch to
the correct position.
in the full power position.
full power.
Use an extension cord of permissible
The extension cord is too long or has
length and of adequate cross section
an inadequate cross section.
(see 6.2).
Connect the tool to a different power
The voltage provided by the electric
source.
supply is too low.
If the fault cannot be remedied by the measures listed above, the power tool should be checked at a Hilti
service center.
The overheating prevention cut-out
has been activated.
Unstable electric supply (under- or
overvoltage cut-out activated).
18
18
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
10. Disposal
Most of the materials from which Hilti power tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking
back your old power tools for recycling. Please ask your Hilti customer service department or Hilti representative
for further information.
Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
11. Manufacturer’s warranty – tools
Hilti warrants that the tool supplied is free of defects
in material and workmanship. This warranty is valid so
long as the tool is operated and handled correctly,
cleaned and serviced properly and in accordance with
the Hilti Operating Instructions, and the technical system is maintained. This means that only original Hilti
consumables, components and spare parts may be
used in the tool.
This warranty provides the free-of-charge repair or
replacement of defective parts only over the entire lifespan of the tool. Parts requiring repair or replacement
as a result of normal wear and tear are not covered by
this warranty.
Hilti is not obligated for direct, indirect, incidental
or consequential damages, losses or expenses in
connection with, or by reason of, the use of, or inability to use the tool for any purpose. Implied warranties
of merchantability or fitness for a particular purpose
are specifically excluded.
For repair or replacement, send tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti's entire obligation with regard to
warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.
Additional claims are excluded, unless stringent
national rules prohibit such exclusion. In particular,
19
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
en
12. EC declaration of conformity (original)
Designation:
Type:
Year of design:
Breaker
TE 706
2004
en We declare, on our sole responsibility, that this product
complies with the following directives and standards:
2000/14/EC, EN 60745-1, EN 60745-2-6, 2006/42/EC,
2004/108/EC, EN ISO 12100, 2011/65/EU.
Measured sound power level
LWA:
Guaranteed sound power level
LWAd:
Conformity assessment procedure:
European
Notified Body:
100 dB/1pW
102 dB/1pW
2000/14/EC
Annex VI
TÜV NORD CERT,
Am TÜV 1, 30519 Hannover,
Germany
Designation:
Type:
Year of design:
Breaker
TE 706-AVR
2004
We declare, on our sole responsibility, that this product
complies with the following directives and standards:
2000/14/EC, EN 60745-1, EN 60745-2-6, 2006/42/EC,
2004/108/EC, EN ISO 12100, 2011/65/EU.
Measured sound power level
LWA:
Guaranteed sound power level
LWAd:
Conformity assessment procedure:
European
Notified Body:
97 dB/1pW
101 dB/1pW
2000/14/EC
Annex VI
TÜV NORD CERT,
Am TÜV 1, 30519 Hannover,
Germany
Hilti Corporation, Feldkircherstrasse 100,
FL-9494 Schaan
Hilti Corporation, Feldkircherstrasse 100,
FL-9494 Schaan
Paolo Luccini
Jan Doongaji
Head of BA Quality and Process Management
Ececutive Vice President
BA Electric Tools & Accessories
BU Power Tools & Demolition
01/2012
01/2012
Paolo Luccini
Jan Doongaji
Head of BA Quality and Process Management
Ececutive Vice President
BA Electric Tools & Accessories
BU Power Tools & Demolition
01/2012
01/2012
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
Technical documentation filed at:
Hilti Entwicklungsgesellschaft mbH
Zulassung Elektrowerkzeuge
Hiltistrasse 6
86916 Kaufering
Deutschland
20
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
Hilti Corporation
Printed: 20.04.2017 | Doc-Nr: PUB / 5136225 / 000 / 01
00
282213 / A2
282213
Hilti = registered trademark of Hilti Corp., Schaan
W 3031 | 0113 | 10-Pos. 8 | 1
Printed in Germany © 2013
Right of technical and programme changes reserved S. E. & O.
*282213*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com