Instruction manual
TUMBLE DRYER
Contents
GB
Installation, 2
EN
English
Where to install the tumble dryer
Ventilation
Electrical connections
Levelling the tumble dryer
Before you start your dryer
Warnings, 4
General safety
Saving energy and respecting the environment
Care and maintenance, 6
Disconnecting the power supply
Cleaning the filter after each cycle
Checking the drum after each cycle
Cleaning the tumble dryer
Description of the tumble dryer, 7
IDVL 75B R
Features
Control panel
How to carry out a drying cycle, 9
Starting and selecting a programme
Programmes and options, 10
Programme chart
Special programmes
Options
Opening the door
Laundry, 13
www.indesit.co.uk
!
Sorting laundry
Care labels
Drying times
This symbol reminds you to read this
instruction manual.
Troubleshooting, 14
! Keep this manual at hand for immediate reference whenever
Spare parts
Information on recycling and disposal
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or transferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
Assistance and Guarantee, 15
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
1
Installation
Install the dryer far
from gas ranges, stoves,
radiators or hobs, as
flames may damage it.
If the dryer is installed
below a worktop, ensure
there are 10 mm betwe15 mm
15 mm
en the upper panel of the
dryer and any objects
above it, and 15 mm
between the sides of the machine and the
walls or furniture units adjacent to it. This ensures adequate air circulation. Make sure the
air inlets on the rear panel are not blocked or
obstructed.
• You should also make sure that the room
in which the tumble dryer is installed is not
damp, and that it is adequately ventilated.
• ! We do not recommend that the dryer is
installed in a cupboard but the dryer must
never be installed behind a lockable door,
a sliding door or a door with a hinge on the
opposite side to that of the dryer door.
• ! The appliance must be installed with the
rear surface placed against a wall.
•
10 mm
GB
Where to install the tumble dryer
Ventilation
This appliance gently dries laundry by taking in cold, clean
and relatively dry air, heating it and passing it through the
fabric. To facilitate the drying process, damp air is expelled at
the rear, through a ventilation hose. When the dryer is in use,
there has to be adequate ventilation to avoid a back flow
of gases into the room from appliances burning other fuels,
including open fires.
Mobile ventilation system
When using the tumble dryer with the mobile ventilation
system, a ventilation hose must be connected. The hose
should be securely fastened to the ventilation hole at the
rear of the appliance (see “Description of the tumble dryer”).
We recommend the hose is connected to an outlet near
the tumble dryer, if possible. If it cannot be installed in a
permanent spot, the tumble dryer will still function perfectly
well if the ventilation hose is passed through a partiallyopened window.
! Make sure you do not point the ventilation hose towards
the air inlet, which is located on the rear of the appliance.
! The ventilation hose should not exceed a maximum length
of 2.4 metres; it should also be shaken frequently to remove
any fluff, dust or water deposits inside it. Make sure you do
not crush the hose.
Fixed ventilation system
We recommend the ventilation hose is connected to a
ventilation system for windows or doors, available from the
retailer which originally sold you the appliance or from your
local spare parts stockist.
2
Wall ventilation hole
1. Leave an opening in the wall
to the left of the tumble dryer
installation site.
2. Make the hose as short and
straight as possible, in order
to prevent any moisture from
condensing and leaking back
into the appliance.
3. The hole in the wall must
also be straight and pointing
downwards, so that the flow of air coming out is not
impeded.
Areas A and B should be checked frequently, to prevent
the accumulation of fluff or debris, particularly if the tumble
dryer is used very often. The hose adaptor must be fitted
correctly, in order to prevent damp air from coming back into
the room.
B
A
Window ventilation hole
The ventilation hole should
be directly behind the dryer in
order to keep the hose as short
as possible.
! Make sure you do not
push the tumble dryer too
far backwards, as this could
lead to the ventilation hose
being crushed, bent or even
disconnected.
! There should be no cuts, kinks or “U”-shaped bends
in the hose, as these could impede ventilation or trap
condensation.
Ventilation through an open window
The end of the hose must be
facing downwards, in order to
prevent the hot, damp air from
forming condensation in the
room or the tumble dryer.
! Make sure that the tumble dryer is adequately ventilated,
and that the end of the ventilation hose is not pointing
towards the air inlet pipe on the rear of the appliance.
! The ventilation hose must always be fitted to ensure
optimum performance.
! Make sure that the ventilation hose and the air inlet vents
are not obstructed or blocked.
! Do not let the tumble dryer recirculate exhaust air.
! Improper use of the tumble dryer may result in fire hazards.
! The air emitted by the tumble dryer must not be expelled in
the same duct as used for the fumes produced by different
appliances which burn gas or other fuels.
! Do not discharge the exhaust air into an extraction system
or any duct with an extractor fan. This will affect the way the
thermal controls operate and can result in a fire hazard.
Electrical connections
Before plugging the appliance into the socket, check the following:
• Make sure your hands are dry.
• The socket must have an earth connection.
• The socket must be able to withstand the
machine’s maximum power output as indicated on the rating plate (see Description of the
tumble dryer).
• The power supply voltage must fall within
the values indicated on the rating plate (see
Description of the tumble dryer).
• The socket must be compatible with the
dryer’s plug. Should this not be the case,
replace the plug or the socket.
! DO NOT USE EXTENSION CORDS.
! The dryer must not be installed outdoors,
even if the space is sheltered. It can be very
dangerous if exposed to rain or storms.
! Once installed, the dryer’s electrical wire
and plug must be within reach.
! The power cord must not be bent or
squashed.
! If the plug being replaced is a non-rewirable
type, then the cut-off plug must be disposed
of safely. DO NOT leave it where it can be
inserted into a socket and create a shock
hazard.
! The electric cord must be regularly
checked. If the supply cord is damaged, it
must be replaced by the manufacturer, its
service agent or similarly qualified persons in
order to avoid a hazard. (see Service). New or
longer power cords are supplied at an extra
charge by authorized dealers.
! The manufacturer denies any responsibility
should any of these rules not be followed.
! If in doubt about any of the above
consult a qualified electrician.
GB
Before you start your dryer
Once the tumble dryer is installed, clean the inside of the
drum before operating it and remove any dirt accumulated
during transportation.
Levelling the tumble dryer
The tumble dryer should be installed level in order to
operate correctly.
After installing the tumble dryer in its permanent position,
make sure it is level; check its side-to-side levelling first,
followed by front-to-back.
If the tumble dryer is not perfectly level, use a wooden
block to support it while you adjust the two front feet, up
or down as necessary.
3
Warnings
GB
! This appliance has been designed and built according to
international safety standards. These warnings are given for
safety reasons and must be followed carefully.
General safety
•This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
•Children should be supervised to ensure
that they do not play with the dryer.
•Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
vents behind the machine, the outlet
vents and the vent tube should never be
obstructed (see Installation).
• Never direct the vent tube outlet towards
the air intake at the back of the machine.
• Never allow the tumble dryer to recycle
exhaust air.
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
•
The back of the dryer could become very
hot. Never touch it while in use.
• Do not use the dryer unless the filter, is
securely in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
•C
● arefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
4
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
• ●Do not dry garments that have been treated
with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed to
heat sources such as a tumble dryer. The
items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates
heat. If the heat cannot escape, items can
become hot enough to catch fire. Piling,
stacking or storing oil-effected items can
prevent heat from escaping and so create
a fire hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or those
that have been contaminated with hair care
products be placed in a tumble dryer they
should first be washed with extra detergent
- this will reduce, but not eliminate the
hazard. They should not be removed from
the dryer and piled or stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed in,
soaked in or soiled with petrol/gasoline,
dry cleaning solvents or other flammable
or explosive substances. Highly flammable
substances commonly used in domestic
environments including cooking oil,
acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
• ●Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• ●Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• ●Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
WARNING: Never stop the dryer before the
end of the drying cycle unless all items are
quickly removed and spread out so that the
heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Maximum load sizes: 7 kg
GB
Product Data - Regulation 392/2012.
Brand
Indesit
Model
IDVL 75 B R (UK) - IDVL 75 B R K (UK) - IDVL 75 B R S (UK)
Rated capacity of cotton laundry for the "standard cotton
programme" at full load - kg
7.0
This household tumble drier is a
Energy efficiency class on a scale from A+++ (low consumption)
to D (high consumption)
Vented
The weighted Annual Energy Consumption (AEc)* kWh 1)
This household tumble drier is a
Energy consumption full load; Edry - kWh 2)
Energy consumption partial load; Edry½ - kWh 2)
Power consumption: off-mode (Po) - Watts
Power consumption: left-on mode (Pl) - Watts
Duration of the 'left-on mode' for power management system minutes
474.2
Automatic
4.04
2.12
0.42
2.24
Prog. Time - weighted (Tt) full & partial load - minutes 3)
Full load (Tdry) - minutes
Partial load (Tdry½) - minutes
Condensation efficiency class on a scale from G (least efficient) to
A (most efficient)
Average condensation efficiency - %
weighted (Ct) full & partial load 3)
full load (Cdry)
partial load (Cdry½)
Airborne acoustical noise emissions - dB(A) re 1 pW
B
30
79
108
58
N/A
69.0
1) The "standard cotton” at full and partial load are the standard programmes to
which the information in the label and the fiche relates. The standard cotton
program is suitable to dry at cupboard level (0%) cotton laundry and is the most
efficient programme in terms of energy consumption. Partial load is half the rated
load.
2) based on 160 drying cycles of the standard cotton programme at full and partial
load, and the consumption of the low-power modes. Actual energy consumption
will depend on how the appliance is used.
3) Weighted average of 3 cycles at full load and 4 cycles at half load.
Regulation 932/2012.
Energy consumption in kWh, for program “Synthetics” full load
Programme time in minute, for program “Synthetics” full load
1.49
45
Partial load for program “Synthetics” N/A
5
Care and maintenance
GB
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once drying is completed, by
rinsing it under running water or cleaning it
with a vacuum cleaner. Should the filter become clogged, the flow of air inside the dryer
will be seriously hampered: drying times becomes longer and more energy is consumed.
Moreover, the dryer may become damaged.
The filter is located
behind of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic
handle upwards (see
Picture).
2. Clean the fluff off
the filter and replace it
correctly. Ensure that
the filter is pushed fully
home.
! Do not use the dryer unless
the filter has been replaced in
its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum.
A coloured film may appear on the stainless steel drum
surface: it may be caused by a combination of water and/or
cleaning agents such as fabric conditioners. This coloured
film does not affect the dryer’s performance.
Cleaning the tumble dryer
• The external metal and plastic parts and the rubber parts
can be cleaned with the aid of a damp cloth.
• Periodically check the vent hose and all other parts of the
venting system and remove any accumulations of fluff and
lint.
6
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechanical parts work safely (see Assistance).
Description of
the tumble dryer
Front side
Rear side
Control panel
3
4
5
Air inlet
Rating Plate
Caution, high
temperature
Filter
Serial number
and model
number
2
Drum
GB
6
7
8
9
10
Connection for
ventilation hose
11
12
13
14
15
595
Control panel
Options
buttons and
indicator lights
Drying phase
or Delay timer
indicator lights
Programme selection knob
with OFF
Start/Pause button
and indicator light
Maintenance
indicator lights
7
Modification:
Modificacao:
Ревизия:
Opis
Modyfikacji:
Degisiklik:
Modifica:
Errore: Nessun riferimento
Errore: Nessun riferimento
General
Tolerancias
Tolerances:
gerais:
Неуказанны
Tolerance
Tolerancje
General:
еOgolne:
Допуски:
Tolleranze
Genel Toleranslar:
Generali:
RCT:
Approval:
Visto:
Согласовано:
Visa:
Zatwierdzil:
Vize:
Modified
Modificado
by:
o:
Изме
Modifié
Zmodyfikowal:
нил
par:
: yapan:
Degisikligi
Modificato
da:
Вес:
Poids:
Waga:
Peso:
Weight:
Agirlik:
Volume:
Обьем:
Objetosc:
Hacim:
Criado
Created
o:
by:
Wykonal:
Разработал:
Crée
par:
Ilk cizen:
Creato
da:
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Ness
Formato:
Size:
Scale:
Escala:
Ф
ормат: М
Echelle:
Skala:
асш таб:
Format:
Olcek:
Scala:
GB
Programme selection knob
Allows for setting the programme: turn until the indicator points towards the desired programme. The OFF position switches off the
dryer (see Starting and selecting a programme).
Options buttons
Allow for selecting the options available for the selected programme. The relative indicator lights switch on when the option has been
selected (see Programmes and options).
START/PAUSE button and indicator light
When the green light flashes slowly, press the button to start the programme. When the cycle is under way, the indicator light remains
on. To put the programme into pause mode, press the button again; the indicator light will turn orange and start flashing again.
To resume the programme from the point it was interrupted, press the button again (see Start and programme selection).
Indicator lights
The indicator lights provide important information. They indicate the following:
“Clean filter” indicator light
Before each programme, the “Clean filter” indicator light
tumble dryer (see Care and maintenance).
signals that it is essential to clean the filter each time before using the
“Drying phases” indicator lights
The
DRYING indicator light signals that the drying phase is running.
The
COOL TUMBLE indicator light signals that the cooling phase is running.
The END indicator light signals that the programme has ended.
“Delay start” indicator light
If the ”Delay start” option has been activated (see “Programmes and options”), after the programme has started, the indicator light
corresponding to the chosen delay time will start flashing:
As time passes, the remaining delay will be displayed and the corresponding indicator light will flash:
Once the set delay time ends, the flashing LED will turn off and the set programme will start.
8
How to carry out
a drying cycle
Starting and selecting a programme
GB
1. Plug the dryer into the power supply socket.
2. Select the programme according to the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed (see Care and maintenance).
4. Load the machine, making sure that no piece of laundry gets between the door and the relative seal. Close the door.
5. After consulting the programme chart and the indications for each type of fabric (see Laundry), turn the Programme selection
knob towards the programme corresponding to the type of laundry to be dried (see Programmes and options).
! Warning: If the position of the programme selection knob changes after pressing the START/PAUSE button, the selected programme will NOT be modified. To modify the programme, press the START/PAUSE button to put the programme in pause mode (the
indicator light flashes orange), then select a new programme and the relative options. Press the START/PAUSE button to start the
new programme.
6. If necessary, set the time of the delayed start and any other options (see Programmes and options).
7. Press the START/PAUSE button to start the drying cycle.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START/PAUSE button to resume machine operation.
8. The final COOL TUMBLE phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme; always
allow this phase to terminate.
9. When the END indicator light turns on, the programme has ended. The buzzer will beep 3 times to let you know that your programme is complete. Open the door, remove the laundry then clean the filter and replace it. (see Care and maintenance).
If the clothes are not removed at the end of the cycle the automatic POST CREASE CARE action will, on those programmes with
this feature, continue to rotate the drum intermittently for up to 10 hours to minimise creasing. The phase is stopped when the door
is opened or when the knob is set to OFF
10. Set the program knob to OFF to switch off the machine.
11. Disconnect the dryer from the power supply.
Automatic pre-post Anti Crease
This is an automatic function which provides an anti crease treatment both before and after the drying programme. By periodically
rotating the drum before the start of the drying cycle, when a delayed start is selected, the formation of creases is prevented. On
certain programmes the drum also rotates periodically at the end of the drying cycle on. The phase is stopped when the door is
opened or when the knob is set to OFF
Stand-by mode
This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby system which is enabled
after about 30 minutes if no activity is detected.
Turn the knob to the desired program to restart dryer operation (to start the program press START/PAUSE). The OFF position
switches off the dryer.
9
Programmes and options
Programme chart
GB
Programme
Max. load
(kg)
Compatible options
Cycle
duration*
Energy Saver
1 Eco Cotton
2
Delay timer
60'
2 Eco Synthetics
1
Delay timer
30'
Cottons
3 Standard Cotton
Max
Delay timer - Light Drying
120'
4 Cotton Extra Dry
Max
Delay timer
130'
5 Cotton Fast Iron
Max
Delay timer - Light Drying
100'
6 Synthetics
4
Delay timer - Light Drying
55'
7 Easy Mix
3
Delay timer
100'
8 Wool
1
-
50’
4
Delay timer
55’
1 pair
Delay timer
110'
3
Delay timer
65’
Special Care
Sport&Leisure
9 Fitness
10 Sport Shoes
11 Jeans
My Time
12 Smart 15’
13 Xpress 35’
14 Daily 60’
1.5
Delay timer - Light Drying
-
1
Delay timer - Light Drying
-
2
Delay timer - Light Drying
-
-
-
Extra
Freshen Up
20’
* note: The duration of these programs will depend on the size of the load, types of textiles, the spin speed used in your washer
and any extra options selected.
Programmes
Energy Saver
The Energy Saver Cycles reduce energy consumption and so they not only help the environment, they also cut your energy bill!
Energy Saver Cycles are available for several different types of fabric and they have been designed to give excellent drying performance for small loads.
Energy Saver Cycles give the best drying results thanks to perfect temperature regulation and to accurate humidity detection which
is optimized small loads.
Cottons
Standard Cotton: Dries your items to a dryness level that allows you to put your clothes away straight from the dryer.
Cotton Extra Dry: Dries your items to the maximum possible dryness level. Even drier than Cupboard dry.
Cotton Fast Iron: Dries your items to a dryness level that allows them to minimise ironing.
Synthetics
Recommended to delicately dry synthetic fabrics.
Easy Mix
This programme is ideal for drying cotton and synthetic fabrics together.
10
Wool
This programme is specific for items that withstand tumble drying and are labelled with the symbol. It is suitable for loads of up to
1 kg (about 3 jerseys). We recommend turning the garments inside out before drying them. Garments dried with this programme are
usually ready to be worn, although the edges of heavier garments may be slightly damp. Leave them to dry naturally, as an additional drying process may damage them.
! Unlike other materials, the shrinking process in wool is irreversible, i.e. the garment does not resume its original dimension and
shape.
! This programme is not suited for acrylic items.
Fitness
This programme is studied for safely drying garments such as tracksuits and Fitness suits bearing the
up to 4 kg. We suggest turning garments inside out before drying them.
symbol. Suitable for loads of
Special Shoes Programme
This programme is specific for drying sports shoes. The shoes must have been previously washed and spun at a minimum spin
speed of 400 revolutions.
A specific shoe rack is provided and must be used, otherwise the dryer will be damaged if shoes are dried in the drum. Remove the
filter from its holder on the front part of the dryer and position the shoe rack.
Place shoelaces inside the shoes then load with the tips of the shoes facing downwards and the soles frontwards.
Drying times vary according to the shape and type of the shoe. If the shoes are not completely dry at the end of the programme,
restart the programme.
! Do not dry shoes that have gel or flashing lights inside them. Only dry shoes made of synthetic material or rope. Once the programme ends, remove the shoe rack and replace the filter into its holder.
Jeans
●This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.
● Do not mix dark and light coloured items.
It can also be used on other garments made from the same material, such as jackets.
● Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is
the case, try turning the jeans inside out and running the programme again for a short period.
! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.
My TiME (15’ - 35’ - 60’)
These programmes can be used if you want to set drying time and temperature.
The COOL TUMBLE cycle runs during the final minutes of the programme.
Damp to Dry 15’ timed programme is ideal to remove damp from tea towels and bath robe used once.
Xpress 35’: this is a quick timed programme, ideal for drying garments spun at high speed in the washing machine, for example
shirts used in a work week.
Daily 60’: a timed programme, ideal for drying garments spun at high speed in the washing machine, for example a change of
sheets.
Freshen Up
A short programme suitable for refreshing fibres and garments. It lasts about 20 minutes.
! As this is not a drying programme, it is not to be used for garments that are still wet.
● It can be used on any load size but is more effective on smaller loads
11
GB
Options
GB
The options allow for customising the selected programme according to one’s own needs.
Delay timer
The start of some programmes (see Programmes and options) may be delayed up to 9 hours. Press the button repeatedly to enter
the desired delay time. Before setting a delayed start, make sure that the filter is clean.The drum will rotate occasionally before the
drying programme starts to prevent the formation of creases.
Child Lock
Prevents the program settings from being changed. After having selected the program and the available options, hold down the two
option buttons for 3 seconds (see “Dryer description”)
A prolonged beep will sound when the buttons are pressed and the LEDs on the options buttons will flash slowly twice. The LEDs
on the previously selected options will then remain lit but will no longer be modifiable.
If you attempt to change the settings with Child Lock activated, 3 short beeps will sound and 3 rapid flashes will warn you that it is
not possible to modify the program or the options underway.
Hold down the options buttons for three seconds to deactivate the Child Lock option. Child Lock can be selected with all
programs.
Light Drying
Light Drying is a special option designed to gentle dry delicate clothes.
Press this button to select the low temperature setting; the light next to the button will switch on. Activating this option will increase
the duration of the cycles
! Not all options are available on all programmes (see Programmes and options).
Opening the door
If the door is opened (or the START/PAUSE button is pressed) while a programme is running, the dryer stops and the following may
occur:
• The START/PAUSE button flashes orange.
• When a delayed start is running, the delay countdown continues. It is necessary to press the START/PAUSE button to resume the
“Delay timer” programme. One of the “Delay timer” indicator light flashes to signal the delay time entered.
• It is necessary to press the START/PAUSE button to resume the programme. The progress indicator lights signal the running phase and the START/PAUSE indicator light stops flashing and turns green.
• When post care phase is active it means that drying programma is already ended. Pressing the START/PAUSE button reactivates
a new programme from the beginning.
• By turning the Programme selection knob, a new programme is selected and the START/PAUSE indicator light flashes green. This
procedure can be used to select the COOL TUMBLE programme to cool garments if they are judged to be dry enough.
Press the START/PAUSE button to start the new programme.
Note: If you have a power cut, switch off the power or remove the plug. When power is restored, plug in the machine. Turn the
knob to the desired program to restart dryer operation (to start the program press START/PAUSE). The OFF position switches off
the dryer.
12
Laundry
Sorting laundry
Drying times
• Check the symbols on the care labels of the various garments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Non caricare l’asciugatrice con capi totalmente pieni
d’acqua.
! Per evitare un calo delle prestazioni dell’asciugatrice, non
sovraccaricarla.
Massime dimensioni di carico
Non caricare il cestello oltre la capacità massima.
I seguenti valori si riferiscono al peso dei capi asciutti:
Fibre naturali: massimo 7 kg
Fibre sintetiche: massimo 4 kg
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
GB
Drying times are approximate and may vary depending on
the following:
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The weight refers to dry items.
Automatic drying times
Cotton
Drying times after 800-1000 rpm wash cycles - with an initial humidity level of 60%
1 kg
2 kg
3 kg
4 kg
5 kg
6 kg
7 kg
20 - 30 minutes
35 - 45 minutes
45 - 60 minutes
60 - 70 minutes
70 - 80 minutes
80 - 100
minutes
90 - 120
minutes
Synthetics
Light drying
Drying times after wash cycles at lower speeds - with an initial humidity level of 40%
1 kg
2 kg
3 kg
4 kg
20 - 40 minutes
30 - 50 minutes
40 - 70 minutes
55 - 90 minutes
13
Troubleshooting
GB
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical
Assistance Centre (see Assistance).
Problem:
Possible causes / Solutions:
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The the fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
•The START/PAUSE button has not been pressed (see How to carry out a drying
cycle).
The drying cycle does not start.
• A delayed start time has been set (see Programmes and options).
•The START/PAUSE button has been pressed; a short delay follows before the dryer
starts running. Wait for the drying cycle to start; do not press the START/PAUSE
button otherwise the dryer switches to the pause mode and the drying cycle will not
start.
Drying times are too long.
• The filter has not been cleaned (see Care and maintenance).
• The heat setting is not suited to the type of fabric to be dried (see Programmes and
options).
• An incorrect drying time was selected for the type of load (see Laundry).
• The flexible ventilation hose may be blocked (see Installation).
• The air inlet may be blocked or obstructed (see Installation).
• The fixed ventilation flap, on the protective weatherproof cover, may be obstructed
(see Installation).
• The items are too wet (see Laundry).
• The dryer is overloaded (see Laundry).
The programme is finished but the
items are damper than expected.
! For safety reasons, the dryer programmes last a maximum of 4 hours. If an
The dryer is noisy during the first
few minutes of operation.
• This is normal, especially if the dryer has not been used for a long time. If the noise
persists during the entire cycle, contact the Technical Assistance Centre.
The lights on the dryer control
panel are off although the dryer is
switched on.
• The dryer has gone into standby mode to save power. This occurs if you have left
the dryer on or have had a power cut. It occurs after 30 minutes:
- if you leave the dryer without starting a programme;
- after your drying programme has finished.
Girando la manopola sul programma desiderato l’asciugatrice riprenderà a funzionare
(per avviare il programma premere START/PAUSA). La posizione OFF spegne
l’asciugatrice.
14
automatic programme has not detected the final dampness level required in this
interval, the dryer completes the programme and stops. Check the above points and
repeat the programme; if the items are still damp, contact the Technical Assistance
Centre (see Assistance).
Assistance
Before contacting the Technical Assistance Centre:
Spare parts
• Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical Assistance Centre closest to you.
This dryer is a complex machine. Attempting to repair it personally or with the aid of an unqualified personnel may put
the safety of people at risk, damage the machine or invalidate the spare parts guarantee.
Always contact a qualified technician when experiencing
problems with this machine.
Provide the following data when contacting the
Technical Assistance Centre:
• name, address and postal code
• telephone number
• type of malfunction
• date of purchase
• the appliance model (Mod.)
• the dryer’s serial number (S/N)
This information can be found on the data plate located
behind the door.
Information on recycling and disposal
As part of our continual commitment towards environmental protection, we reserve the right to use recycled quality components to
reduce costs for our customers and to minimise materials wastage.
• Disposing of the packaging materials: follow local regulations to allow for recycling of packaging materials.
• In order to minimise the risk of injury to children, remove the door and plug, then cut the power supply cord flush with the appliance. Dispose of these parts separately to prevent the appliance from being connected to a power supply socket.
Disposal of old household appliances
European Directive 2012/19/EC concerning Waste Electrical and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected
separately in order to optimise the cost of re-using and recycling materials comprising the machine, while preventing
potential damage to public health and the environment. The crossed-out wheeled bin symbol appears on all products to
remind owners of the obligations regarding separate waste collection.
Owners should contact their local authorities or appliance dealers for further information concerning the correct disposal of household appliances.
This appliance conforms to the following EU directives:
- 2006/95/EC (Low Voltage Directive)
- 2004/108/EC (Electromagnetic Compatibility Directive).
15
GB
06/2014 - Xerox Fabriano
GB
Essential Contact Information
INDESIT SERVICE - Service You Can Rely On
At Indesit we pride ourselves on offering our customers the best service we possibly can, wherever you are in the UK and Ireland.
Rest assured though, no one knows an Indesit appliance better than we do and our service is second to none…
Wherever you are we can be there – we have over 1,000 highly skilled Indesit engineers covering the whole of the UK and Ireland
ensuring fast, reliable, local service.
‘Right first time’ – our engineers have the latest tools to help get your Indesit appliance back up and running the first time we visit.
Experts in our field – all of our engineers are trained to the highest standard at our Training Centre of Excellence and possess
unrivalled expertise and product knowledge.
Skilled staff – we have over 400 skilled UK based call centre staff, dedicated to offering you excellent service 364 days a year.
Telephone in the United Kingdom: 08448 224 224
Telephone in the Republic of Ireland: 0818 313 413
Please note:
Our advisors will require the following information:
•
•
•
•
name, address and postal code
telephone number
type of malfunction
•
•
model number
serial number
This information can be found on the data plate located
behind the door.
date of purchase
Indesit Company S.p.A.
Viale Aristide Merloni, 47
60044 Fabriano (AN)
16