Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
Hot Water
Dispensers
Supercedes
10052.0000; 10010.0000; 10267.0000
10420.0000; 10889.0000; 39338.0000
39338.0001; 44306.0000
INSTALLATION & OPERATING GUIDE
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
To ensure you have the latest revision of the manual or to obtain the illustrated parts catalog, please visit
the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain
the latest catalog and manual updates. Contact Bunn-O-Matic Corporation at 1-800-286-6070 to obtain
a paper copy of the required Illustrated Parts Catalog mailed via U.S. Postal Service.
46819.0000A
06/12 © 2012 BUNN-O-MATIC CORPORATION
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal servers
and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor.
2) All other equipment - 2 years parts and 1 year labor plus added warranties as specified below:
a) Electronic circuit and/or control boards - parts and labor for 3 years.
b) Compressors on refrigeration equipment - 5 years parts and 1 year labor.
c) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis - parts
and labor for 4 years or 40,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by it will be
commercially free of defects in material and workmanship existing at the time of manufacture and appearing within the
applicable warranty period. This warranty does not apply to any equipment, component or part that was not manufactured
by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, alteration, improper installation or operation,
improper maintenance or repair, non periodic cleaning and descaling, equipment failures related to poor water quality,
damage or casualty. In addition, the warranty does not apply to replacement of items subject to normal use including but
not limited to user replaceable parts such as seals and gaskets. This warranty is conditioned on the Buyer 1) giving BUNN
prompt notice of any claim to be made under this warranty by telephone at (217) 529-6601 or by writing to Post Office
Box 3227, Springfield, Illinois 62708-3227; 2) if requested by BUNN, shipping the defective equipment prepaid to an
authorized BUNN service location; and 3) receiving prior authorization from BUNN that the defective equipment is under
warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN are not authorized to make
modifications to this warranty or to make additional warranties that are binding on BUNN. Accordingly, statements by such
individuals, whether oral or written, do not constitute warranties and should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts and/or labor (during the
applicable parts and labor warranty periods specified above) to repair the defective components, provided that this repair
is done by a BUNN Authorized Service Representative; or 2) shall replace the equipment or refund the purchase price for
the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF THIS
EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S SOLE OPTION
AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of
use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities
or services, or any other special, incidental or consequential damages.
392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN
Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic,
Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design,
Dual, Easy Pour, EasyClear, EasyGard, FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, Intellisteam, My Café, Phase Brew, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with
the stylized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel,
Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh,
Titan, trifecta, Velocity Brew, A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Profit
Calculator, Brew better, not bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Daypart, Digital Brewer
Control, Nothing Brews Like a BUNN, Pouring Profits, Signature Series, Tea At Its Best, The Horizontal Red Line, Ultra are
either trademarks or registered trademarks of Bunn-O-Matic Corporation.
2
46819 030912
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
CONTENTS
Warranty����������������������������������������������������������������������������������������������������������� 2
Introduction����������������������������������������������������������������������������������������������������� 3
User Notices������������������������������������������������������������������������������������������������������ 4
Electrical Requirements������������������������������������������������������������������������������� 5
Plumbing Requirements��������������������������������������������������������������������������������� 6
Initial Set-Up (H5E, H5X, H5-PC, H5 Element, H10X)������������������������������������� 6
Initial Set-Up H5M, HW2, OHW������������������������������������������������������������������������� 7
OPERATING CONTROLS (H5-PC ONLY)����������������������������������������������������������������� 8
ADJUST DISPENSE VOLUME (H5-PC ONLY)��������������������������������������������������������� 8
Programming (H5E, H5X, H5-PC, H10X)���������������������������������������������������������� 9
Programming (H5 Element)������������������������������������������������������������������������� 11
Draining the Dispenser�������������������������������������������������������������������������������� 14
Cleaning������������������������������������������������������������������������������������������������������������ 14
INTRODUCTION
This equipment heats and dispenses water on demand for beverages and cooking purposes. It has a panel
above the faucet that indicates the status of the dispenser. This equipment is for indoor use, either wall-mounted
(H5E/X/PC) or on a sturdy counter or shelf.
Brew water temperature is factory set at 200° F (93.3° C)
Areas of high altitude will require lowering this temperature to prevent boiling. This chart should be used as a
guide when readjusting the brew water temperature.
(Feet)
Boiling point
of water
°F
°C
-1000
-500
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
5500
6000
6500
7000
7500
8000
8500
9000
9500
10000
213.8
212.9
212.0
211.1
210.2
209.3
208.4
207.4
206.5
205.6
204.7
203.8
202.9
201.9
201.0
200.1
199.2
198.3
197.4
196.5
195.5
194.6
193.7
Altitude
3
101.0
100.5
100.0
99.5
99.0
98.5
98.0
97.4
96.9
96.4
95.9
95.4
94.9
94.4
93.9
93.4
92.9
92.4
91.9
91.4
90.8
90.3
89.8
Recommended
water temperature
°F
°C
200
200
200
200
200
200
200
200
199
198
197
196
195
195
194
193
192
191
190
189
188
187
186
93.3
93.3
93.3
93.3
93.3
93.3
93.3
93.3
92.8
92.2
91.7
91.1
90.6
90.6
90.0
89.4
88.9
88.3
87.8
87.2
86.7
86.1
85.6
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
USER NOTICES
The notices on this dispenser should be kept in good condition. Replace unreadable or damaged labels.
NOTICE
ALL COMPONENTS ARE
200 TO 240 VOLT A.C.
Replace only with
components listed in the
accompaning literature
rated for the same
voltage
00824.0002
00824.0001
12537.0000
00833.0000
00657.0000
As directed in the International Plumbing Code of the
International Code Council and the Food Code
Manual of the Food and Drug Administration (FDA),
this equipment must be installed with adequate
backflow prevention to comply with federal, state
and local codes. For models installed outside the
U.S.A., you must comply with the applicable Plumbing /Sanitation Code for your area.
00656.0001
NOTICE
Optional Field Wiring
ALL COMPONENTS ARE
200 TO 240 VOLT A.C.
120 V, 15.4 A, 1850 W
1PH, 2-Wire + GND, 60HZ
Replace only with
components listed in the
accompaning literature
rated for the same
voltage
12537.0000
29710.0000
29710.0000
Optional Field Wiring
To reduce the risk of electric shock,
do not remove or open cover.
No user-serviceable parts inside.
Authorized service personnel only.
Disconnect power before servicing.
120/208-240 V, 16.9 A, 4050 W
1PH, 3-Wire + GND, 60HZ
29710.0000
37881.0000
! WARNING
Fill water tank before turning - on thermostat or connecting appliance
to power source.
Use only on a properly protected
circuit capable of the rated load.
Electrically ground the chassis.
Follow national/local electrical codes.
Do not use near combustibles.
! WARNING
Hot Water
Use With Care
12593.0000
120V
120/208-240V
00831.0000
FAILURE TO COMPLY RISKS EQUIPMENT
DAMAGE, FIRE, OR SHOCK HAZARD
READ THE ENTIRE OPERATING MANUAL
BEFORE BUYING OR USING THIS PRODUCT
THIS APPLIANCE IS HEATED WHENEVER
CONNECTED TO A POWER SOURCE
To reduce the risk of electric shock,
do not remove or open cover.
No user-serviceable parts inside.
00831.0000F 3/98 ©1998 BUNN-O-MATIC CORPORATION
00831.0000
Authorized service personnel only.
Disconnect power before servicing.
37881.0002
4
46819 061212
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
ELECTRICAL REQUIREMENTS
WARNING - The dispenser must be disconnected from the power source until specified in Initial Set-Up.
Refer to Data Plate on the Brewer, and local/national electrical codes to determine circuit requirements.
WHITE
NEUTRAL
L1 BLACK
NEUTRAL WHITE
N
L1 BLACK
POWER CORD
L2 RED
L1
L1 BROWN
GREEN
120 volt ac models
Note: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate
conductor for earth ground.
L2 RED
L1
L2
L1 BLACK
L1
GREEN
G
POWER CORD
L2 RED
L1 BLACK
GREEN/YELLOW
G
POWER CORD
NEUTRAL BLUE
N
L1 BLACK
G
230 volt ac models
Note: This electrical service consists of 2 current carrying conductors (L1 and Neutral) and a separate
conductor for earth ground.
Electrical Hook-Up
CAUTION – Improper electrical installation will damage electronic components.
1.An electrician must provide electrical service as specified.
2.Using a voltmeter, check the voltage and color coding of each conductor
at the electrical source.
3.Turn off master switch (if equipped).
4.Remove the upper and lower rear panels.
5.Install the proper electrical wiring to the terminal block.
6. Connect the dispenser to the power source and verify the voltage at
the terminal block before proceeding. Reinstall both rear panels.
7.If plumbing is to be hooked-up later be sure the dispenser is disconnected from the power source. If Plumbing has been hooked-up, the
dispenser is ready for Initial Set-Up.
CE REQUIREMENTS
• This appliance must be installed in locations where it can be overseen
by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• Appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specified in conformance
with all local and national codes.
• This appliance must not be cleaned by water jet.
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given instructions concerning use
of this appliance by a person responsible for its safety.
• Children should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel with a special cord available from
the manufacturer or its authorized service personnel in order to avoid a
hazard.
• Machine must not be immersed for cleaning.
5
208 & 240 volt ac models
Note: This electrical service consists
of 2 current carrying conductors (L1
and L2) and a separate conductor for
earth ground.
POWER CORD
L2 RED
L2 RED
WHITE
NEUTRAL WHITE
N
NEUTRAL
L1 BLACK
L1 BLACK
L2
L1
GREEN
G
120/208 & 120/240V ac
single phase models
Note: This electrical service consists
of 3 current carrying conductors
(Neutral, L1 and L2) and a separate
conductor for earth ground.
DUAL VOLT TOGGLE SWITCH
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PLUMBING REQUIREMENTS - ALL EXCEPT OHW
This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi
(138 and 620 kPa)from a ½˝ or larger supply line. A shut-off valve should be installed in the line before the dispenser. Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345
kPa). The water inlet fitting is ¼˝ flare.
NOTE - Bunn-O-Matic recommends ¼˝ tubing for installations of less than 25 feet and 3⁄8˝ for more than 25 feet
from the ½˝ water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as reinforced
braided polyethylene or silicone, before the dispenser will facilitate movement to clean the countertop. BunnO-Matic does not recommend the use of a saddle valve to install the dispenser. The size and shape of the hole
made in the supply line by this type of device may restrict water flow.
As directed in the International Plumbing Code of the International Code Council and the Food Code Manual
of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow
prevention to comply with federal, state and local codes. For models installed outside the U.S.A., you
must comply with the applicable Plumbing /Sanitation Code for your area.
Plumbing Hook-Up
1. Remove the shipping cap from the fitting on the rear of the dispenser, and attach the flare elbow fitting
(supplied separately with the dispenser) to the fitting.
2. Flush the water line and securely attach it to the flare fitting.
Plumbing Hook-Up
Master ON/OFF switch
INITIAL SET-UP - H5E, H5X, H5-PC, H10X, Element
CAUTION - The dispenser must be disconnected from the power source throughout the initial set-up, except
when specified in the instructions.
1. Connect dispenser to the power source and turn on water supply.
2. Place Master ON/OFF switch in the ON position (if equipped). NOTE: (Digital models with display) When
power is applied to the dispenser, the display will show the software version for 5 seconds, and then it will
show the temperature.
3. Water will automatically flow into the tank to the proper level and shut-off. When filled, the water heater will
turn on automatically.
4. The tank will heat to the (set) temperature.
5. Refer to Programming to set the Tank Temperature and the Ready Temperature.
6
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
INITIAL SET-UP - H5M
CAUTION - The dispenser must be disconnected from the power source throughout the
initial set-up, except when specified in the instructions.
1. Remove the upper rear panel and rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the panel.
2. Connect the dispenser to the power source and turn-on the water supply.
3. Water will automatically flow into the tank to the proper level and shut-off. This
will take approximately 10 minutes.
4. Disconnect the dispenser from the power source, remove the upper rear panel
and place the control thermostat knob fully clockwise to the “ON” position, and
replace the panel.
5. Connect the dispenser to the power source and wait approximately twenty
minutes for the water in the tank to heat.
6. On models with ready indicator, the indicator will light up when the proper water
temperature is achieved.
INITIAL SET-UP - HW2
CAUTION - The dispenser must be disconnected from the power source throughout
the initial set-up, except when specified in the instructions.
H5M
1. Remove the center rear panel and rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the panel.
2. Plug-in the dispenser.
3. Water will automatically flow into the tank to the proper level and shut-off.
4. Unplug the dispenser, remove the center rear panel and rotate the control thermostat knob fully clockwise to the “ON” position, and replace the panel.
5. Plug-in the dispenser and wait approximately twenty minutes for the water in the
tank to heat. The dispenser is ready for use.
INITIAL SET-UP - OHW
CAUTION - The dispenser must be unplugged throughout the initial set-up,
except when specified in the instructions.
1. Place an empty vessel under the faucet, lift the pour-in lid, and pour a full pitcher
(64 oz) of tap water into the top of the dispenser. Hold open the faucet handle
to allow air to escape from the tank while it is filling.
2. Pour another full pitcher into the top. Close the faucet when water starts flowing
from the faucet.
3. Fill the top basin with additional water until it is approximately one inch from
the top lid.
4. Plug-in the dispenser and wait approximately 15 minutes for the water to heat
to the proper temperature.
5. The dispenser is now ready for use. (refer to the section on normal use.)
HW2
NORMAL USE
CAUTION - Water dispensed from this faucet is extremely hot . (Above 200° F.)
1. Hold open the faucet whenever a cup of hot water is desired.
2. Pour another full pitcher into the top whenever water is no longer available at
the faucet. No wait is needed, the faucet is ready to dispense another cup of
hot water.
NOTE - Due to the tank capacity and heater size, this product should be used only
for dispensing a few cups of hot water at a time. (Larger capacity Bunn-OMatic hot water dispensers are available.)
7
OHW
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
OPERATING CONTROLS - PORTION CONTROL ONLY
d.
(a) VOLUME SELECTOR BUTTONS
Press and release the button corresponding to the Small, Medium, or
Large volume, to select the desired
amount of water to be dispensed.
Pressing a different button after a
cycle has been initiated does not
change the volume in progress.
(b)AUTO STOP/MANUAL DISPENSE
BUTTON
Press and release button to stop a
dispense cycle. Press and hold button
to dispense manually.
(c) HIDDEN PROGRAMMING BUTTON
(d)LED INDICATORS
(e)DISPENSE NOZZLE
c.
a.
b.
e.
ADJUSTING DISPENSE VOLUMES
NOTE: The dispenser should be at operating temperature before setting dispense volumes.
1. Press and hold the hidden programming button (c) located under the ® next to the BUNN logo on the front
of the dispenser until the 3 LED's begin flashing from the left to the right. Release the button.
2. Place an empty graduated container under the dispense nozzle (e).
3. Press and release the batch size to be set (a). The LED's will stop flashing, and the LED over the button just
pressed will come on steady. Water will begin to dispense into the container.
4. When the desired amount of water is dispensed, press and release the same button (a). The water will stop
dispensing and the batch size is now set.
5. The LED's will begin flashing from left to right again. Repeat steps 2 thru 4 to set up the other batch sizes.
6. To exit the programming set up at any time, press and release the hidden button once (c). The dispenser is
now ready for use.
8
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PROGRAMMING - H5-E, H5-PC, H5X, H10X
When power is applied to the dispenser, the display located on the bottom of the main circuit board will show
the software version for 5 seconds, and then it will show the model number (see chart below) it will then go
to (-). While the tank is filling, the display will read (FIL). When the tank is full the display will show the model
number and then go to (-).
MODEL DISPLAYS (P1)
(H5H)
(H5L)
(HPC)
(H10)
5 Gallon High Voltage Unit (200-240V)
5 Gallon Low Voltage Unit (100-120V)
5 Gallon Portion Control Unit (all)
10X (all)
Switch must be in “SET” position for
access into programming modes.
LEFT
BUTTON
CENTER
BUTTON
RIGHT
BUTTON
LEVEL 1 PROGRAMMING
1. Before programming any settings into the Control Board, confirm the correct model
number is entered.
2. Do this by pressing and holding down on the center button until P1 appears on the
display. Release the center button. The display will now show the model number
(ex: H5H). Now scroll with the (+/-) buttons through the models listed above until
the display matches the model you are working with.
3. Press and release the center button once more. The display will show P2. Display
will now show the tank temperature (ex: 200). Press the (+) button to increase the
temperature set point, or the (-) button to decrease the set point.
NOTE: If the unit is a H5X or H10X, set the Tank Temperature to 212°F.
4. After the Tank Temperature is entered, press and release the center button once
more. The display will read P3, then show the ready temperature set point. Factory
default is 195° F for most dispensers, and 85° F for some.
5. Press the (+) button to increase the set point, or the (-) button to decrease the set
point.
6. To exit Level 1 Program press and release the center button once more. The display
will show Software version, then model number, then (-).
Continued
9
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PROGRAMMING - H5-E, H5-PC, H5X, H10X Continued
LEVEL 2 PROGRAMMING
H1 - DISPENSE TEMPERATURE LOCKOUT - PORTION CONTROL ONLY
(WILL NOT DISPLAY ON OTHER MODELS)
1. To enter Level 2 Programming, press and hold the center button until H1 appears on the display (approximately 6 seconds) then release button. The display
will either read noL (LOCKOUT DISABLED) or Loc (LOCKOUT ENABLED). When
(ENABLED), unit will not dispense if the Tank Temperature is below the (READY)
temperature setting.
2. Use the (+) or (-) buttons to alternate between Loc and noL.
3. Press and release the center button once more to advance to H2.
Or to exit Level 2, press and release the center button 3 times. Display will show,
software version, then model number, then (-).
H2 - F° OR C° SELECTION
NOTE: Skip step 1 if going from H1 to H2.
1. To enter Level 2 Programming, press and hold the center button until H2 appears
on the display (approximately 6 seconds). Release the center button, The display
will show either FAH (Degrees in Fahrenheit) or CEn (Degrees in Centigrade).
2. Press and release the (+) or (-) buttons to alternate between FAH and CEn.
3. After setting FAH or CEn, to exit Level 2 Programming, press and release the center
button twice. Display will show, software version, then model number, then (-).
H3 - RESTORING FACTORY DEFAULTS
1. To restore Factory Defaults (This clears all settings that were previously entered),
press and release the center button until H2 appears on the display (approximately
6 seconds). Release the Center Button, then press and release the Center Button
once more. The display will read H3, then show (- - -).
2. Press and hold both (+) and (-) buttons to initiate the resetting of the factory
default settings. The display (- - -) will flash on and off during this time (about 5
to 7 seconds).
3. When the factory default numbers are loaded in, the display will stop flashing,
then read don (DONE). You can now release the two buttons.
NOTE: If you release the two buttons at any time before the display reads don, the Factory Default numbers will not be entered. The old numbers will remain in the memory.
4. To exit Level 2 Programming press and release the center button once more. The display will show the
Software version, then model number, then (-).
10
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PROGRAMMING - H5-ELEMENT
Adjusting temperature:
The switch must be in the “SET” position in order to
access the program modes.
1. Press and hold “TEMP” button until display
flashes.
2. While display is flashing, press and release the
(+) to increase or (-) to decrease temperature.
NOTE: (Starting with software version 0.06)
If unit is “E” model, temp will stop at 210°F (99°C).
If unit is “X” model, temp display will jump from
210°F (99°C) to 212°F (100°C).
Manual Energy Saver Mode:
The energy save mode will allow the tank temperature
to drop down to 140°F (60°C).
1. Simultaneously press and release the (+) and (-)
to “manually” activate energy save mode.
2. The display will alternately flash between 140
and the current temperature to indicate it is in
the energy save mode.
3. Repeat procedure to exit energy save mode.
Step forward
Refer to chart on page 3 and adjust temperature
requirements according to altitude.
Program lockout switch:
The switch must be in the “SET” position in order to
access the program modes.
1. Disconnect the dispenser from the power source.
2. Remove the 4-40 screws and the top cover.
3. Use a small screwdriver to move switch to set
position.
4. Install top cover, connect dispenser to power
source.
Step backward
LO
CK
SE
T
Programming the dispenser:
1. Press and hold upper hidden button (bottom
center of “BUNN” logo) until “P1” is displayed.
Continued
11
46819 061212
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PROGRAMMING - H5-ELEMENT Continued
2. The display will now show the model number.
(H5H)
5 Gallon High Voltage Unit (200-240V)
(H5L) 5 Gallon Low Voltage Unit (100-120V)
Now scroll with the (+/-) buttons through the models listed above until the display
matches the model you are working with.
3. Press and release the upper hidden button once more. The display will show P2.
Display will now show the “SET” temperature (ex: 200). Press the (+) button to
increase the temperature set point, or the (-) button to decrease the set point.
Range: 60°F (15°C) to 210°F (99°) NOTE: Temp will skip to 212°F (100°C) on H5X.
4. After the Tank Temperature is entered, press and release the upper hidden button
once more. The display will read P3, then show the ready temperature set point.
Range: 2° to 20° below the “SET” temperature.
5. Press the (+) button to increase, or the (-) button to decrease the set point.
6. Press and release the upper hidden button once more. The display will read P4.
This screen will allow you to turn the “Auto” energy save mode ON/OFF.
NOTE: Turning off this function will disable “P5” and “P6”.
7. Press and release the upper hidden button once more. The display will read P5.
This will toggle the energy save mode from 140°F (60°C) or tank heater “OFF”.
8. Press and release the upper hidden button once more. The display will read P6.
This is the time delay from the last refill to the activation of energy save mode.
Range: 4 hours to 24 hours.
Continued
12
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
PROGRAMMING - H5-ELEMENT Continued
LEVEL 2 PROGRAMMING
H2 - F° OR C° SELECTION
1. To enter Level 2 Programming, press and hold the upper hidden button until H2
appears on the display. Release the upper hidden button. The display will show
either FAH (Degrees in Fahrenheit) or CEn (Degrees in Centigrade).
2. Press and release the (+) or (-) buttons to alternate between FAH and CEn.
3. After setting FAH or CEn, to exit Level 2 Programming, press and release the upper hidden button twice. Display will show, software version, then main screen.
H3 - RESTORING FACTORY DEFAULTS
1. To restore Factory Defaults (This clears all settings that were previously entered),
press and release the upper hidden button until H2 appears on the display (approximately 6 seconds). Release the upper hidden Button, then press and release
the upper hidden Button once more. The display will read H3, then show (- - -).
2. Press and hold both (+) and (-) buttons to initiate the resetting of the factory
default settings. The display (- - -) will flash on and off during this time.
3. When the factory default numbers are loaded in, the display will stop flashing,
then read don (DONE). You can now release the two buttons.
NOTE: If you release the two buttons at any time before the display reads don, the Factory Default numbers will not be entered. The old numbers will remain in the memory.
13
46819 043012
Total Restaurant Supply - https://totalsupply1.com - Toll Free 1-800-944-9304 - Local 507-288-9454
2940 Hwy 14 W, Rochester, MN 55901
DRAINING THE DISPENSER - OHW
CAUTION - The dispenser must be disconnected from the power source throughout these steps.
1.
2.
3.
4.
Disconnect the dispenser from the power source and allow dispenser to cool.
Tilt dispenser forward over sink.
Open faucet.
Continue tilting dispenser forward over sink until water stops flowing.
NOTE - The dispenser must be full using the INITIAL SET-UP steps before reconnecting to the power source.
DRAINING THE DISPENSER - ALL 2, 5 & 10 GALLON MODELS
CAUTION - The dispenser must be disconnected from the power source throughout these steps.
1.
2.
3.
4.
5.
Disconnect the dispenser from the power source.
Shut-off and disconnect the incoming water supply and allow dispenser to cool.
Remove the 4-40 screws and the top cover.
Gently remove one of the grommets from the tank lid.
Insert a tube to the bottom of the tank and syphon ALL of the water out.
CLEANING
The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all
surfaces on Bunn-O-Matic equipment.
WALL MOUNTED INSTALLATION - 5 GALLON MODELS ONLY
If the dispenser is wall mounted, the bottom of the dispenser should be at the same height as a counter or
table top. Use B.O.M. part #12542.0000 for side mounted Wall Bracket Kit or # 13125.0001 for front mounted
Wall Bracket Kit .
SUPPORT FOR LARGE RECEPTACLES
CAUTION: If the dispenser is to be used with larger receptacles such as pitchers or pots, those receptacles must
be adequately supported during dispensing of hot water to avoid spillage of very hot water. This support may be
provided by a table or counter top, or use B.O.M. part #12599.0000 Shelf Kit.
14
46819 043012