INSTALLATION MANUAL
MOSER STAINLESS STEEL BATHROOM FAUCET
MODEL MADRID
STEP 1SINK SPECIFICATIONS
Thank you for your purchase of a MoSER faucet. With proper care and maintenance, your new faucet will
bring you years of trouble free enjoyment. We welcome any questions or comments you may have and look
forward to assisting you.
For more information about MoSER Sinks and Faucets products, please visit our website at:
www.mosersinks.com
To ensure that your installation proceeds smoothly, please
carefully read the installation and maintenance instructions.
Remember to inspect your faucet for any noticeable damage
and verify all parts and pieces are in the box. Verify all local
applicable plumbing and building codes. The following
instructions are based on application in a residential setting.
For the installation of MoSER stainless steel faucets,
we suggest using only licensed plumbers. Please note
acceptable variances are approximately 1/16 of an inch.
Alignment to the pre-drilled hole cut-out and precise
application and trimming of any adhesive sealant are critical
for a superior fit and finished look. Please take extra care
when installing MoSER stainless steel faucet.
MoSER does not accept any liability for damage to your
countertop, sink fixture, faucets or personal injury during
installation. Warranty is void if installation instructions are not
properly followed.
!
Important note:
i. Ensure that the cold and hot water
lines are turned off.
ii. Wrap all threaded connections
with Teflon tape. Be sure to always
wrap in a clockwise direction.
iii. Cover the sink drain to avoid losing
parts.
iv. Do not disassemble the main
faucet body, as it has been
precision factory assembled.
v. Verify that working pressure is
between 0.05-1.00MPa (including
both hot and cold water) and that
water temperature is between 4oC
and 90oC
Tools and material you may require:
»» Adjustable Wrench
»» Teflon Tape
»» Silicone Adhesive
»» Rags
»» Eye Protection
»» Phillips Screwdriver
»» Pencil (not ink)
»» Denatured Alcohol
»» Tape Measure
Be sure to use proper tools and always wear personal safety devices for your protection.
!
To avoid the risk of fresh water contamination due to back-siphonage,
do not connect this faucet to a portable washing device such as a dishwasher.
STEP 1SINK SPECIFICATIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Hot and Cold Waterline
Screws
Lock Nut
Metal Washer
Rubber Ring
Washer
Nozzle
Filter
Washer
Faucet Body
Ceramic Cartridge
Clamp Nut
Cover
Handle
M5 Screw
Finishing Cap
STEP 1SINK SPECIFICATIONS
STEP 1
Insert faucet body in the pre-drilled 1 3/8” hole
STEP 2
Insert rubber ring (5), metal washer (4), lock nut (3) and
lock nut screws (2).
STEP 3
Use Phillips Screwdriver to tighten lock nut screws.
STEP 1SINK SPECIFICATIONS
STEP 4
Connect hot and cold waterlines (1) to faucet.
Tighten until snug.
STEP 5
Wrap Teflon tape to the threaded portion of the shut
off valves.
Verify if O-rings are present on both ends of the hot
and cold waterlines.
Connect hot and cold waterlines to the shut off
valves. Tighten with an adjustable wrench until
snug.
Ensure handle is in the “off” position
Turn on water supplies and check for leaks.
NOTE
In the event longer waterlines
than those supplied are required,
installer must purchase additional
parts separately
STEP 6
Turn faucet on and ensure proper flow.
Turn faucet off.
STEP 1SINK SPECIFICATIONS
Legal Disclaimer
All technical data and information provided in this publication is done as a public service to customers of MoSER Sinks and Faucets
(MoSER) and consumers of its products. All names, designs, and model numbers of products are the property of MoSER. Prices and
specifications of MoSER products are subject to change without notice or obligation. MoSER may also change or discontinue models
of its products without notice or obligation. While MoSER endeavors to provide accurate information and descriptions of its products,
accuracy and completeness cannot be guaranteed. MoSER is not responsible for, nor does it have any liability for any mistakes
or typographical errors, including liability for incidental, consequential, or special damages. All products should be inspected and
measured promptly upon delivery and certainly before any improvements or alterations are done in anticipation of or preparation for
installation. MoSER assumes no liability for the use of such information or for any damages incurred through its use or applications.
Nothing contained in this publication is to be construed as contractual or providing any form of warranty or representation on the
part of MoSER. MoSER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY
OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, AS TO THE INFORMATION CONTAINED HEREIN OR THE
PRODUCTS DESCRIBED HEREIN.
mosersinks.com
Download PDF
Similar pages
This faucet is warranted to the original consumer purchaser to be
19" Emmed SPECIFICATIONS
Douos SPECIFICATIONS
Beemlen SPECIFICATIONS
Amity SPECIFICATIONS
Eclipse SPECIFICATIONS
Melik SPECIFICATIONS
Conifer SPECIFICATIONS