WARNING LIGHTING │ DIRECTIONAL LIGHTING │ LIGHTBARS │ WHITE LIGHTING │ REVERSING SAFETY
DIRECTIONAL LEDS
9031 Hide-A-LED™
Pop-In Mount / Concealed Warning LEDs
The 9031 is a high-intensity directional LED warning light specifically designed for
vehicle headlight and tail-light applications. The optic design produces wide angle light
dispersion and maximizes secondary light output reflected off the vehicle light casing. In
addition, the LEDs’ low profile allows mounting in small, confined light casings typical of
tail lights and modern vehicle headlights. The LED design offers major advantages over
strobe versions. All control electronics are situated in a sealed, in-line driver module so no
remote power supply is required. 16 flash patterns are included and multiple units can be
synchronized to flash alternately or simultaneously. Additional benefits of LED technology
include high intensity light output, low current draw and a long and maintenance-free
service life. And, they’re covered by a full 5-year warranty.
Head/Tail Light
Reflector
1” Hole
Plug-in
Models
LED HEAD
PART NO.
COLOR
VOLTAGE
AMPS
9031A
9031C
Amber
Clear
12-24
12-24
0.35
0.35
FLASH
PATTERNS
16
16
MOUNT
1” Hole
1” Hole
1.09
[28]
1.09 [28]
0.860.86
[22][22]
1.34 [34]
Features and Benefits
1.34 [34]
• Four 1-watt high-intensity LEDs per head provide exceptional warning
• Wide-angle light dispersion maximizes light casing reflection
• 16 flash patterns including single, double, triple, quad, deci and cycle all
• Multiple heads are synchronizable (simultaneous or alternating operation)
• Colorless when not illuminated
• In-line waterproof driver module eliminates the need for a remote power supply
• UV stabilized polycarbonate lens, nickel plated housing and 9’ cable
DRIVER MODULE
4.83 [123]
4.83 [123]
.47 [12]
.93 [24]
T 800-635-5900 │ orders@eccogroup.com
www.eccoesg.com
An ECCO SAFETY GROUP™ Company
.47 [12]
.93 [24]
9031 SERIES
Pop-In Mount / Concealed Warning LEDs
WARNING LIGHTING │ DIRECTIONAL LIGHTING │ LIGHTBARS │ WHITE LIGHTING │ REVERSING SAFETY
Flash Patterns
Flash patterns are selected by touching the blue wire momentarily to power; the LED head will cycle through the available patterns.
#
1
2
3
4
5
6
7
8
S T A N D A R D
Patterns
Quad Flash
Double Flash
Triple Flash
Deciblast
Single Flash
Mega Flash
Triple+Burst
Steady On
Frequency
1.25 Hz
1.25 Hz
1.25 Hz
1.25 Hz
1.25 Hz
1.25 Hz
1.25 Hz
P A T T E R N S
Description
75 Quad FPM
75 Double FPM
92.3 Triple FPM
85.5 Deci FPM
75 Single FPM
114 Single FPM
82.5 Triple + Burst FPM
Steady On
#
9
10
11
12
13
14
15
16
C Y C L E
Patterns
Cycle All
Double-Triple + Burst
Cycle Classic
Quad-Mega
Single-Quad
DeciBlast-Quad
Single-Triple-DeciBlast
Mega-Triple+Burst
P A T T E R N S
Frequency
Description
Cycle through patterns 1 to 7
2 Double, 2 Triple + Burst cycle
1 Double, 1 Quad, 2 Mega cycle
3 Quad, 4 Mega cycle
2 Single, 2 Quad cycle
2 DeciBlast, 2 Quad cycle
2 Single, 2 Triple, 2 DeciBlast cycle
1 Mega, 1 Triple+Burst cycle
Alternating/Simultaneous Flash Selection
The yellow wire on each LED head is used to determine alternating or simultaneous operation with other heads in the system that are connected
using the blue wire. The yellow wire has no function when ‘Steady On’ flash pattern is selected.
• Connect the YELLOW wire to either POWER or GROUND
• Heads with YELLOW connected to POWER fire SIMULTANEOUSLY with other heads connected to POWER
• Heads with YELLOW connected to GROUND fire SIMULTANEOUSLY with other heads connected to GROUND
• Heads with YELLOW connected to POWER fire ALTERNATELY with other heads connected to GROUND
Note: The blue wires of all LED heads must be connected together for the alternating/simultaneous function to operate.
Wiring Diagram
The diagram below shows a typical installation of 4 HIDE-A-LEDs™ using an on/off switch. The left and right side heads are configured to flash
alternately with each other using the blue wire to connect the two with the yellow wire on one connected to ground and the yellow wire on
the other connected to power.
YELLOW
TO - GND
YELLOW
TO +V
RED
BLACK
RED
BLUE
YELLOW
BLACK
BLUE
YELLOW
YELLOW
TO +V
ON/OFF
FUSE
YELLOW
TO - GND
ALTERNATE FLASHING
ALTERNATE FLASHING
RED
CHASSIS
GROUND
The front and rear heads are configured to flash independently of each other. In order to have the front and rear heads flash in sychronization,
the blue wires from all units must be connected. The yellow wire can then be used to determine either alternate or simultaneous flash between
each unit in the system by connecting to either power or ground.
T 800-635-5900 │ orders@eccogroup.com
www.eccoesg.com
An ECCO SAFETY GROUP™ Company