important safeguards important instructions 19. save these

POWER
MODE
OSCILLATE
70°
F
F/C
DIGITAL CERAMIC
HEATER
HZ-335, HZ-336 Series
IMPORTANT
SAFEGUARDS
READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS
HEATER.
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock, and injury to persons, including the
following:
IMPORTANT
INSTRUCTIONS
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surface. If provided, use handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 3 feet (0.9 m)
from the front of the heater and keep them away from
the sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
dropped or damaged in any manner. Return heater
to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist indoor locations. Never
locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or the like. Arrange cord
away from traffic areas where it will not be tripped
over.
1
9. This appliance has a polarized plug (one blade is
wider than the other). To reduce the risk of shock,
this plug is intended to fit only one way in a polarized
outlet. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this
safety feature.
10. This heater draws 12.5 amps during operation. To
prevent overloading a circuit, do not plug the heater
into a circuit that already has other appliances working.
11. It is normal for the plug to feel warm to the touch;
however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion
of the plug. Contact a qualified electrician to replace
loose or worn outlet.
12. To disconnect the heater, first turn controls to the
OFF position, then grip the plug and pull it from the
wall outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside.
Do not use it in the areas where gasoline, paint, or
flammable liquids are used or stored.
16. Use this heater only as described in this manual.
Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
17. Avoid the use of an extension cord because the
extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated
not less than 1875 watts.
18. The output of this heater may vary and its temperature may become intense enough to burn exposed
skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to
react to avoid burns.
SAVE THESE
INSTRUCTIONS.
19.
MODE: SET TIMER
BASIC CONTROL PANEL OPERATION:
Timer
POWER
Continuous Run
High Power
Low Power
• Press Mode until the Timer icon blinks. The Hour
display will appear.
• Use the Up or Down arrows to set an operation time
between 1 and 10 hours.
• The heater will turn-off when time runs out.
• Press Power once to start the heater on High Power,
Continuous Run.
• Press Power again to change to Low Power, Continuous
Run.
FAHRENHEIT/CELSIUS
• Press Power a third time to turn the heater off.
MODE: SET TEMPERATURE
Set Temperature
F/C Temperature
Display
• F/C feature functions from only the Power or Set
Temperature screens.
• Press the F/C button to toggle between Fahrenheit
and Celsius.
• Press Mode until the Temperature icon blinks. The
current room temperature will appear.
• Use the Up or Down arrows to set the desired temperature.
• The Temperature icon will stop blinking and the current room temperature will reappear after the
desired temperature is set.
• The heater will turn-off shortly after the desired temperature is reached and the Power light above the
display will blink.
• The heater will turn back on when the room temperature drops approximately 2 degrees below the
desired temperature. The Power light will stop
blinking and will remain lit.
2
OSCILLATION
POWER:
High Power
Low Power
Power
• The Oscillation feature functions in any power or
mode setting.
• Press the Oscillation button to toggle this feature on
and off.
Basic Remote
LCD Remote
• Press Power once to start the heater on High Power,
Continuous Run.
• Press Power again to change to Low Power, Continuous Run.
• Press Power a third time to turn the heater off.
REMOTE CONTROL OPERATION (HZ-336
SERIES):
MODE: SET TEMPERATURE
Two (2) AAA batteries required.
Set Temperature
Model HZ-336:
Remote Control included when originally purchased.
Model: HZ-335:
Remote Control may be purchased separately at:
www.honeywellconumerproducts.com
Mode
Adjust Up or
Down
The Remote Control works the same as the corresponding buttons on the Control Panel. The
Control Panel display on the heater will show the
appropriate icons when the various functions are
activated.
Basic Remote
LCD Remote
• Press Mode until the Temperature icon blinks. The
current room temperature will appear.
• Use the Up or Down arrows to set the desired temperature.
• The Temperature icon will stop blinking and the current
room temperature will reappear after the desired temperature is set.
• The heater will turn-off shortly after the desired temperature is reached and the Power light above the display will blink.
• The heater will turn back on when the room temperature drops approximately 2 degrees below the desired
temperature. The Power light will stop blinking and will
remain lit.
3
MODE: SET TIMER
When done, plug-in the heater and follow the
OPERATION INSTRUCTIONS.
Set Timer
For more troubleshooting tips, visit our website at:
www.honeywellconsumerproducts.com
Mode
NOTE: IF YOU CONTINUE TO EXPERIENCE A
PROBLEM, PLEASE RETURN THE HEATER
TO THE PLACE OF ORIGINAL PURCHASE OR
SEE YOUR WARRANTY. DO NOT ATTEMPT
TO OPEN THE HEATER YOURSELF. DOING
SO MAY VOID YOUR WARRANTY AND
CAUSE DAMAGE TO THE HEATER OR PERSONAL INJURY. IF YOU HAVE ANY QUESTIONS REGARDING THIS HEATER, PLEASE
CALL OR WRITE:
Honeywell
Consumer Relations Department
250 Turnpike Road
Southborough, MA 01772
Toll Free 1-800-332-1110
E-mail: honeywell@protocolusa.com
Adjust Up or
Down
LCD Remote
Basic Remote
• Press Mode until the Timer icon blinks. The Hour display will appear.
• Use the Up or Down arrows to set an operation time
between 1 and 10 hours.
• The heater will turn-off when time runs out.
OSCILLATION
CLEANING AND STORAGE:
We recommend that the heater be cleaned at
least once a month and before off-season storage.
• Turn the heater OFF and unplug it. Allow it to
cool completely.
• Use only a dry cloth to clean the external surfaces of the heater. DO NOT USE WATER,
WAX, POLISH, OR ANY CHEMICAL SOLUTION.
• Clean your heater using the above-mentioned
steps, then pack the heater in its original container and store it in a cool, dry place.
• This heater does not disassemble.
Oscillation
Basic Remote
LCD Remote
• The Oscillation feature functions in any power or
mode setting.
• Press the Oscillation button to toggle this feature on
and off.
TROUBLESHOOTING:
ACCESSORIES:
If your heater shuts off unexpectedly, safety features may have been activated to prevent overheating. If this happens:
• Be sure the power cord is plugged into a working electrical outlet.
• Check your thermostat setting. The unit may
simply be off because you have reached your
desired heat setting.
• Check for any obstructions. If you find one,
turn the heater OFF and unplug it. Wait at
least 10 minutes to allow the heater to cool
completely before removing any obstruction.
Your HZ-335 or HZ-336 series heater is compatible with both the Basic and Digital LCD Remote
Control. To upgrade your heater, or to get a listing of heater accessories, visit our website at:
www.honeywellconsumerproducts.com
ELECTRICAL RATING:
This product is rated 12.5 Amps (1500 Watts) at
120 VAC, 60 Hz.
4
time phone number. You must prepay shipping
charges. Send to:
In the US:
Honeywell
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118 USA
5 YEAR LIMITED WARRANTY
You should first read all instructions before
attempting to use this product. Register your
product on-line at
www.honeywellconsumerproducts.com or
complete and return the Customer Response
Card within 7 days.
A. This 5 year limited warranty applies to repair
or replacement of product found to be defective in material or workmanship. This warranty
does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of
normal wear and tear will not be considered
manufacturing defects under this warranty.
• HONEYWELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON
THIS PRODUCT IS LIMITED IN DURATION
TO THE DURATION OF THIS WARRANTY.
Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential
damages or limitations on how long an implied
warranty lasts, so the above limitations or
exclusions may not apply to you. This warranty
gives you specific legal rights, and you also
may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only
to the original purchaser of this product from
the original date of purchase.
B. At its option, Honeywell will repair or replace
this product if it is found to be defective in
material or workmanship. Defective product
should be returned to the place of purchase in
accordance with store policy. Thereafter, while
within the warranty period defective product
may be returned to Honeywell.
C. This warranty does not cover damage resulting from any unauthorized attempts to repair or
from any use not in accordance with the
instruction manual.
D. Return defective product to Honeywell Consumer Products with a brief description of the
problem. Include proof of purchase and a $10
US/$14.50 CAN check or money order for handling, return packing and shipping charges.
Please include your name, address and day-
In Canada:
Honeywell
Attn: Returns Department
510 Bronte Street S.
Milton, ON L9T 2X6 Canada
5