REARS ORCHARD SPRAYERS
MADE IN THE
VERTICAL WALL TOWERS
•
•
•
•
•
Louvered air vanes adjust discharge angle.
Individual target zone spray controls.
Manual or electric air discharge and spray controls.
Available with standard or split manifolds for quick spray height variation control.
Optional adjustable air doors control discharge volume to compensate for wind.
500 gallon with 10’ radius top tower
500 gallon with 13’ folding tower
OESCO, INC. IS ONE OF THE TOP REARS DEALERS IN THE WORLD!
COUNT ON REARS SPRAYERS FOR DURABILITY, PERFORMANCE, AND FLEXIBILITY.
POWERBLAST SPRAYER with
OVER ROW TOWERS
•
•
•
•
•
•
•
Adjustable reach to accommodate your row spacing.
Air dams to tune target turbulence.
Drop tubes and duct arms break away independently.
Folds for easy transport.
Stainless steel construction.
Direct air to tree center from three directions at once: reduce
overspray.
Improved coverage means better pest control.
Visit www.oescoinc.com
to download Rears sprayer
spec sheets.
Pictured on 500 gallon
Narrow Powerblast
with tandem axles
POWERBLAST ENgINE DRIVE SPRAYER
with John Deere Powertech 4.5L diesel engine; 115 HP
turbo charged.
•
•
•
•
•
•
•
•
66
400, 500 or 600 gallon stainless steel tanks
33” or 38” stainless steel fan
Electric fan clutch
Electric throttle
Electric spray controls
REARS centrifugal pump
Stainless steel fan housing
Rollover no-drip nozzles with ceramic tips
500 gallon
with 38” fan
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
REARS POWERBLAST SPRAYERS
OUR BEST SELLING ORCHARD SPRAYERS
POWERBLAST SPRAY SYSTEM
•
Stainless Steel Construction: tank, fittings & hardware,
mechanical agitation, hard plumbing, spray manifolds, fan
housing
•
Rears Constant Velocity Hitch: for smooth 90° turns under
full loads, nothing beats a Powerblast
Rears Centrifugal Pump: 200PSI/80GPM
Rears Spray Control: manual, electric or hydraulic
Double-Rollover Nozzle Bodies: switch your application
rate with a simple twist
33”- 38” Diameter Axial Flow Fan: fitted to the stainless
steel fan housing for optimal performance
Time tested design, wide range of applications: a
flexible, durable system
•
•
•
•
•
MADE IN THE
500 gallon narrow with 33” fan
SEVERAL MODEL PROFILES, AS WELL AS TANK AND FAN SIZES.
500 gallon standard with 33” fan
1000 gallon with 38” fan
The Rears Constant Velocity Hitch bends your tractor’s power around
a corner -- without bending your tractor. For smooth turns, nothing
beats a PowerBlast!
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
67
PUL-BLAST SPRAYERS
MADE IN THE
PuL-BLAST SPRAYERS
100-500 gallon stainless steel tanks, multiple
profile, medium power, adaptive PTO machine. CV
or standard hitch, diaphragm or centrifugal pump,
adjustable pitch fans with a two-speed gear box
make these sprayers adaptable to many tractor sizes
and power requirements. All tanks are provided with
mechanical agitation and electric spray controls.
300 gallon Pul-Blast Blueberry
Special with fenders
Above: 300 gallon Pul-Blast
At top: 200 gallon narrow Pul-Blast
100 gallon Pul-Blast with fenders
200 gallon Pul-Blast with wheel well
cut out in tank for narrower profile
68
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
VINEYARD / HOPS SPRAYERS
MADE IN THE
MADE IN THE
HIGH-REACH HOPYARD SPRAYER - THE PAKBLAST !
REARS 100 gALLON PAKBLAST SPRAYER
This sprayer provides excellent coverage in hops. With proper nozzling and the right tractor horsepower (minimum 45HP) the Rears
Pakblast with 28” fan gets the job done. Choose from manual, hydraulic or electric controls.
Pul-Blast with Grape Hood
100 gallon Pak-Blast
Also shown in hopyard at top
Trellis boom w/ 4 nozzle pipes on Nifty Pul Tank
Pul-Blast with Grape Wall
and Scoops
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
CALL US
TODAY TO
DISCUSS
YOUR
HOPYARD &
VINEYARD
SPRAYER
NEEDS.
69
PAK-BLAST SPRAYERS
PAK-BLAST
The Pak-Blast adapts Rears’ cutting
edge air-blast sprayer design to 3 point
mounted applications. By nesting the
heavy duty gearbox and pump within the
tank profile, Rears has shifted the center
of gravity forward toward the tractor lift
arms. The result is a high-performance
sprayer that can be matched to the most compact orchard
tractor. The Pak-Blast has a selection of aluminum alloy
axial flow fans - 24” to 28” diameter. The fan is fitted to the
fan housing to produce optimal performance. All fans have
variable pitch.
OPTIONAL MANUAL, ELECTRIC OR HYDRAULIC CONTROLS.
50, 75, 100 & 150 GALLON TANK SIZES.
MADE IN THE
50 gallon Pak-Blast
100 gallon Pak-Blast
100 gallon Pak-Blast with manual controls
100 gallon Pak-Blast with grape scoops
70
50 gallon Pak Blast, 24” fan
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
AIR BLAST CROP / ORCHARD SPRAYERS
J-400
jACTO j-400
3 pt. hitch, 105 gallon polyethylene tank with
mechanical agitation, 25 gpm centrifugal
pump, three outlet cannon head w/ hydraulic
lift and rotation available. 40 PTO HP
required. 60’ plus spray swath.
jACTO j-600
3 pt. hitch, 158 gallon polyethylene tank with
mechanical agitation, 35 gpm, PTO driven
centrifugal dual stage pump with hydraulic head
rotation & deflector setting.
50 PTO HP required 90’
swath. The J-600 CHT
is a new version of the
J-600 export, designed
for farmers who have been
using the hydraulic system
of the tractor to move
the cannon head both
vertically and horizontally
while spraying.
J-600
jACTO Aj-401
Economical low output, 3 pt hitch cannon
sprayer with 105 gallon
Poly Tank. Jet
agitation, 25
GPM centrifugal
pump, manual
head rotation and
lift, 25 HP PTO
requirement. 40’
plus swath width.
AJ-401
ENgINE DRIVE SPRAYERS
These small trailer sprayers offer the
power of a tractor-driven sprayer with the
versatility of a narrow self-contained unit.
This 36” wide sprayer features a
Vanguard engine, 20” fan that can be
disengaged, Hypro D30 diaphragm pump,
Teejet nozzles with diaphragm checks, turf
tires and clevis hitch. Available in 50 and
100 gallon tank sizes.
Great for use with an ATV or small garden
tractor in Christmas trees, vineyards, berry
plantations and dwarf orchards.
AgTEC 3004
Medium capacity 3 Pt. hitch 540 rpm PTO
driven air row crop sprayer, 100 gallon
fiberglass tank, 120 gpm centrifugal pump,
Accu-rate meter, 12v electric valves, Model
3000 squirrel cage fan, Model 3000 rotating
row crop head 12 volt operation. Standard
equipment: combination fan housing for
orchard/row crop heads. Options available:
row crop head, orchard head, nut tree heads,
VMC tower heads, 150 gallon tank, hydraulic
rotation, sight gauge in tank, stack extension.
AgTec and jacto manufacture rotating head row crop air sprayers available in 3 pt. hitch and trailer versions.
We also offer row crop volutes that can be attached to existing orchard airblast sprayers for use in row crops.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
71
REARS SKID TANK SPRAYERS
COMMERCIAL SKID SPRAYERS
MADE IN THE
Available with 50-1000 gallon stainless steel, single or multiple tanks with mechanical
agitation. Pumps and engine options available up to 60gPM and 700PSI to meet your
needs. Reels, hoses and guns are available to fit each application.
Rears multiple tank skid sprayer
500/200/200 gallon
John Deere diesel engine
High pressure diaphragm pump
Rears 300 gallon skid
Honda engine
Medium pressure diaphragm pump
Rears 300 gallon skid
Honda engine
High pressure diaphragm pump
Rears multiple tank skid sprayer
Multiple engine and John Bean piston pumps
Rears 100 gallon 304SS low profile skid
Honda engine / Diaphragm pump
72
Rears 600 gallon high pressure skid sprayer
Custom paint colors available
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
REARS NIFTY SPRAYERS
NIFTY SERIES
Available as skid or trailer models with 25, 50 or 100 gallon tank size. All tanks are
stainless steel with mechanical agitation. Trailers are offered with boat trailer tires
or turf style tires. All models have Honda engines and diaphragm pumps for long
life and low maintenance.
50 gallon Nifty skid, AR30 pump, Honda 5.5 HP engine
MADE IN THE
100 gallon Nifty skid, AR30 pump, Honda 5.5 HP engine.
25 gallon Nifty with boat trailer tires
50 gallon Nifty trailer with flotation tires and Rears Nifty Boom
NIfTY NuRSERY CART SPRAYER
• 25 gallon wheelbarrow style Nifty Sprayer.
• Specifications: 25 gallon stainless steel tank, mechanical agitation, stainless lid,
basket strainer, volume sight gauge, suction strainer with valve, pressure gauge,
pneumatic bicycle tires and steel handles.
• Pump: AR 252, 2 diaphragm 6 gpm, 290 psi
• Motor: 3 HP Briggs & Stratton, 3 HP Honda or 1 HP, 110V AC electric motor.
• Accessories: 25’ of 3/8” PVC hose, BR 380 brass spray gun.
• Options: Trailer hitch
Mechanical Agitation for organic spraying
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
73
REARS BOOM SPRAYERS / FOAM MARKERS
MADE IN THE
SPRAY BOOMS
Rears stainless steel tanks with mechanical agitation
are mounted on steel frames using PTO driven
diaphragm pumps. Stainless wet boom pipes provide
the base for steel framed booms. Available with
hydraulic or
manual boom
fold and lift
options. Tank sizes from 50 - 1000 gallons in
3 pt. hitch and trailer.
RMCO hydraulic fold boom on heavy duty Pak-Tank
DP Boom mounted in utility vehicle
with 304 Rears sprayer.
FOAM MARKERS
PAK-MARK
Coil shock boom on Pul Tank
200 gallon Pak-Tank / RMCO 25’ hydraulic fold
boom
Custom paint colors available
12V compressor foam marker available in
several models. Normally used in row crops,
turf, and cranberries. Adapts to any sprayer
or spreader. Requires 12V power supply.
REA PM1-S one sided
REA PM2-S-RC 2 sided / remote control
box
MINI-TRAC 2000 SERIES
An affordable compact foam marker for pasture sprayers & ATVs. Available as dual and
single drop models. Base-ball sized foam
drops, outfits booms up to 30’, use with field
speeds up to 7 MPH. 2 & 4 gallon tanks.
RIC MTD-2020 2 gallon
RIC MTD-2040 4 gallon
Spreaders or sprayers up to 30” wide. 32 oz.
tank, power unit, tubing and mounting
components uses D cell battery.
RIC TT-1101
Spreaders or sprayers up to 8’ wide. 60 oz.
tank, single air pump, remote switch, tubing
12V vehicle battery powered.
RIC TT-3301
For spreaders or sprayers up to 15” wide.
Dual 60 oz. tanks, dual air pumps, remote
switch each side, tubing 12V vehicle battery
powered.
RIC TT-4401
Richway Turf Special Foam Concentrate
RIC TFM01 1 gallon
74
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
THE MOST POPULAR 3 PT. HITCH WE SELL!
REARS PAK-TANK SPRAYERS
PAK-TANK SPRAYERS
Pak-Tank sprayers come standard with stainless steel tanks, mechanical agitation, PTO shaft
driven diaphragm pumps and sway chains. Many models of booms, guns and hose available.
Excellent for small fruit, Christmas trees and general row crop spraying.
25 to 200 gallon size • 3 pt. hitch or front mount
Standard or heavy duty frames
MADE IN THE
50 gallon Pak-Tank with 2 section boom
50 gallon narrow Pak-Tank
200 gallon Pak-Tank Heavy duty frame
Front mount hydraulic drive Pak-Tank
100 gallon Pak-Tank
Orchard Weed Boom
The boom telescopes in length to adjust to the needs of the operator. Mounts right or left side of tractor on transmission belly side. Three stock
models available. Kit includes hose, spring hinge and manual valve. Many options including 12v electric valve. 1, 2, 3 nozzle models
100 gallon Pak-Tank with orchard weed boom
100 gallon Pak-Tank with 3 section boom
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
75
crop care 3pt Boom spraYers
3 PT sprayers offer
superior maneuverability
and minimizing of damage
to crops, particularly in
post-emergence spraying
applications. They are
excellent for farms with
smaller acreages or as a
secondary sprayer.
MADE IN THE
Sprayers can be customized to meet your needs with:
• 55 gallon to 300 gallon tank sizes
• Roller, centrifugal or diaphragm pumps
• Manual fold, hydraulic fold or 1-sided booms
• Single or triple nozzles
• Optional nozzle spacing on some booms
• Quick fill, rinse tank or hose and gun options
Download brochure
30’ MANuAL X-FOLD BOOM
• Heavy-duty powder coated frame
• Boom breakaway system
• Engineered to smoothly fold open or closed
• Standard 20” boom spacing - optional 20-30”spacing
• Covers twelve 30” rows
25’ HYDRAuLIC SINgLE-SIDED BOOM
• Coil spring suspension system helps keep boom stable
in uneven field conditions
• Covers ten 30” rows
• Hydraulic fold, leveling and height adjustments
• Height ranges from 24” to 84”
NEW!
45’ HYDRAuLIC X-FOLD BOOM
• Features heavy duty powder coated frame
• Outer wings made of aluminum to reduce weight and stress on boom
• Spring retraction system removes slack from cables when folding
45’ hydraulic boom unfolded (above) and folded (below left)
other Boom sizes are aVailaBle - call for Details
76
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
CROPCARE TRAILER BOOM SPRAYERS
Trailer sprayers offer bigger tank sizes to cover larger acreage farms, as well
as many options for operator efficiency and effectiveness.
CROPCARE TRAILER SPRAYERS
AgX200T, AgX300T, AgX400T
Standard features:
•
•
•
•
•
Center deck with handrail
Electric controls mounted under deck
Fold up step on – both sides
Adjustable axle spacing with three tire choices
Available choices: 20’ or 30’ manual fold,
25’ hydraulic single side, or 30’, 40’ and
45’ hydraulic X-fold
AgX400T
See it in action
CROPCARE TRAILER SPRAYERS
AgX500T, AgX750T and TR1000
Standard Features:
• Single or triple nozzle bodies
• Agressive jet agitation suspends chemical in
water
• Hinged tank lid on 500, 750 & 1000
• Tool box
• Adjustable hitch height on larger sprayers
• Easy access service deck w/ flip-up steps &
handrail
• Fully adjustable axle spacing
• Boom suspension extension springs & shock
absorbers for smooth, cushioned ride.
AgX750T
Boom Control Options:
• Manual flow control valves for ease and
simplicity (requires open station tractor)
• Electric controls use economical solenoid
valves or ball valves with flowback design
to reduce boom shutoff time and decrease
overlap
• Available with manual or auto rate controls
heaVY-DutY poWDer coateD steel frames
ALL SPRAYERS HAVE A 2 YEAR LIMITED WARRANTY
MADE IN THE
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
77
CROPCARE VEGETABLE EQUIPMENT
MADE IN THE
NEW!
PA 1600
PICKINg ASSISTANT
Designed for all of your small to large
scale crop harvesting, weeding,
planting, and bed maintenance needs.
The PA1600 increases productivity
and efficiency of field workers while
protecting them from weather
Standard features:
• Dual high torque gear motors
• 24 volt variable speed controller
• Includes two 12 volt batteries & two
solar panels for recharging
• Picking height adjustment from 20”
to 30”
• Width adjustment from 36” to 66”
• 2 year limited warranty
• Sold unassembled
PR 2500 PLASTIC MuLCH LIFTER WRAPPER
Standard Features:
See this
equipment in
action
78
• Heavy-duty powder coated steel frame and components
• Easy to operate thumb controls
• Category I and II lift pins
• 2 Year Limited warranty
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
CROPCARE 1-SIDED & SHIELDED BOOM
MADE IN THE
25’ Hydraulic Single-Sided
Boom Sprayers
Standard Features:
• Trailer or 3 PT Hitch mounted
• Heavy-duty powder coated steel frame and components
• Easy to operate manual or electric controls
• Boom breakaway protection
• Quick attach non-drip nozzle bodies
• Dual jet agitation
• In-line filter system
• Wet tested and ready to spray
• 2 Year limited warranty
Download brochure
55 AND 110 Gallon
Shielded Sprayers
Allows highly targeted spraying for weeds without
harming your crop.
Standard Features:
• Heavy-duty powder coated steel frame and components
• In-line filter system
• Quick attach non-drip nozzle bodies
• Jet agitation
• Wet-tested and ready to spray
• Choice of category I or II frame
• Shields are made of tough Lexon plastic
See it in action
• A wheel on the front of the shield allows it
to follow the ground for maximum drift protection
• 2 Year limited warranty
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
79
SPRAYERS
ATX SERIES
•
•
•
•
•
Available in several configurations: trailer, skid or 3 PT hitch
12 Volt diaphragm pumps or PTO roller pumps available
Compact lightweight 12’ and 20’ Booms or boomless nozzles
All models include a spray gun and hose
Powder coated frame
ATX60-3PT
ATX-TR
ATX-SK
ATX-AB MIST SPRAY
ATTACHMENT FOR
ATX SERIES SPRAYERS
Features:
• Husqvarna 580BTS engine
drive blower
• 3 nozzle adjustable head
• Variable metered spray flow control
• Mount for ATX sprayers
LEgENDARY jOHN BEAN SKID SPRAYERS
Positive displacement piston pumps available from 5-60gPM up to 800PSI. Stainless steel, fiberglass or poly tanks in
single or multiple versions. All steel skid frames and mechanical agitation. Contact us for specifications.
We have a huge inventory
of parts for older and newer
John Bean sprayers
MADE IN THE
John Bean multiple tank skid sprayer
600/200/200 gallon
80
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
GREGSON-CLARK SPRAYERS
Scan for more information
and product video
50-Gallon Sprayer V-50 ST
Compact, lightweight and inexpensive. The V-50ST is ideal
for pest control, weed spraying or as a dedicated unit for
special services. With a base width of 38.5” the V-50 ST fits
well in compact trucks.
V-50ST - 50 gallon
100-Gallon Sprayer V-100ST
With a base width of 38.5”, the V-100ST fits well in medium
and full size pickup trucks. By mounting the hose reel under
the pump/engine, the VT-100ST works well in vans with sidedoor access to all controls.
V-100ST - 100 gallon
MOST
POPULAR
200-Gallon Sprayer V-200ST
The V-200ST fits well in a full size pickup, leaving plenty of
space for other equipment or materials.
V-200ST - 200 gallon
Standard 300 Mounting
300-Gallon Sprayer V-300ST
The V-300ST can accommodate two hose reels.The tank is
baffled and features a 16” lid. The 14 GPM pump ensures
plenty of agitation.
V-300ST - 300 gallon
Standard 50, 100, 200 Mounting
Standard features include:
• Honda Engines
• Udor Diaphragm Pumps
• Hannay Reels
• Poly tanks with jet agitation
• Powder coated steel frames
MADE IN THE
Custom systems and
options available
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
81
HANNAY HOSE REELS
The reel leader.
INDuSTRIAL HOSE REELS
Hannay is the leading manufacturer of high
quality hose and cable reels for most every
conceivable application.
Hannay hose reels come in many sizes
and capacities.
SERIES 1500
SERIES 1800
SERIES 6000
Inlet: Standard inlet
is 90° ball bearing
swivel joint with 1/2”
female NPT threads.
Outlet: Standard
outlet is 3/4” male GHT threads.
Operating Pressures to 3000 psi.
Inlet: Standard inlet
is 90° ball bearing
swivel joint with 1”
female NPT threads.
Outlet: Standard outlet is
3/4” male GHT threads.
Operating Pressures to 1000 psi.
Inlet: Standard inlet is a
90° ball bearing swivel
joint with 1” female NPT
threads.
Outlet: standard outlet is
3/4” male GHT threads.
Operating Pressures to 1000 psi.
MODEL
Hose capacity of reel
1/4” I.D.
3/8” I.D.
MODEL
1/2” I.D. 5/8” I.D.
5/8” I.D.
3/4” I.D.
1” O.D.
1-9/32” O.D.
1816-17-18
75 ft.
50 ft.
100 ft.
5/8” O.D. 3/4” O.D. 7/8” O.D. 1” O.D.
1514-17-18
175 ft.
125 ft.
75 ft.
50 ft.
1520-17-18
350 ft.
275 ft.
175 ft.
125 ft.
1822-17-18
150 ft.
1526-17-18
500 ft.
400 ft.
300 ft.
200 ft.
1826-17-18
200 ft.
125 ft.
1530-17-18
—
500 ft.
375 ft.
275 ft.
1830-17-18
275 ft.
150 ft.
1536-17-18
—
—
475 ft.
350 ft.
1836-17-18
350 ft.
200 ft.
HAN 9927.8551 - Replacement swivel 1/2”
Hose capacity of reel
Hose capacity of reel
HAN 9929.8552- Replacement swivel 1”
MODEL
1/2” I.D.
3/4” I.D.
1” I.D.
7/8” O.D.
1-9/32”
O.D.
1-9/16” O.D.
6024-19-21
235 ft.
125 ft.
60 ft.
6032-19-21
350 ft.
200 ft.
100 ft.
6024-23-24
450 ft.
185 ft.
100 ft.
6030-23-24
—
250 ft.
150 ft.
6038-23-24
—
350 ft.
200 ft.
HAN 9929.8552- Replacement swivel 1”
PORTABLE gARDEN HOSE REELS
For grounds maintenance and home use
SERIES gH1100
Inlet: Standard inlet is 90° ball bearing
swivel joint and 1/2” female NPT threads
Outlet: Standard outlet is male GHT
threads. Operating Pressures to 3000 psi.
Hose Capacity: 3/8”(I.D)/300 ft.;
1/2”(I.D.) /200 ft.; 5/8”(I.D.) /150 ft.
HAN gH1100
HAN 9927.8551- Replacement swivel 1/2”
uTILITY HOSE
ROLLERS
SERIES gHAT1200
Inlet: Standard inlet is 90° ball bearing
swivel joint with 1” female NPT threads.
Outlet: Standard outlet is male GHT
threads. Operating Pressures to 1000 psi.
Hose Capacity: 1/2”(I.D.) /375 ft.;
5/8”(I.D) /200 ft.; 3/4”(I.D.) /150 ft.;
1”(I.D.) /100 ft.
HAN gHAT-1200
HAN 9929.8552- Replacement swivel 1”
if you don’t find what you’re
looking for, call OESCO
and we will help you meet
your needs.
82
Stainless steel rollers and
cast alloy brackets for use
on the reel, on cabinet door
openings, truck platforms
and similar locations where
sharp edges may cut or
damage hose/cable.
FH-3 ROLLER AND SPOOL ASSEMBLY
Speeds handling and reduces hose
wear. Buffed stainless steel rollers
resist corrosion, pitting and abrasion.
Polished, chrome-plated spools and
blocks add lasting beauty to your
equipment. Delrin bearing surfaces
assure quiet operation and minimum
wear.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
WEED CONTROL / 12V SPRAYERS
PULMIPUR
The PULMIPUR is an economical alternative to other more expensive
controlled droplet applicators.
Hand-Held CDA Sprayer
Designed for the small grower or homeowner, the 6005 utilizes a 14 1/2” diameter spray
shield to protect your crop. Requires 2 “D” batteries (not supplied). This ultra low volume
hand held sprayer for use with RoundUp®or other herbicides with little or no water, based
on product labeling. With a 1 liter chemical container this lightweight sprayer can go a long
way on a small amount of chemical.
VOL ITA-6005-R - Hand held CDA sprayer • 2 lbs. empty
ATV Sprayers and Accessories
Spot Sprayers are great for treating small and/or isolated areas.
For pesticides, herbicides or liquid de-icing products.
MIGHTY MAC
Gasoline Powered Sprayer
CROPCARE LGX Spot Sprayer
Features:
• Powder coated frame
• Shurflo 12 volt, 1.8 gpm, 60 PSI diaphragm
pump
• TeeJet wand with adjustable nozzle
• Wire harness with switch and fuse
• Available in 25 or 40 gallon model
Trailer package available for 25 gal. model only
• 3 1/2 HP Briggs & Stratton 4-cycle engine
• Hypro twin piston pump, up to 3 gpm/300 psi
• Direct drive from engine to pump
• Durable 22 gal. 200 mil polyethylene tank
• Pistol grip gun / 25’ high pressure, 3/8” hose
• 5 1/2” diameter top opening for easy fill
• Rugged, heavy steel frame
• Pressure relief valve, stainless steel in-line
strainer
• 10.5 x 3.5 turf type pneumatic tires on ball
bearing wheels
• 39”L (plus tow bar) x 29”W x 38”H
• 120 lbs.
MAC PS322T
16 gallon sprayer
16 Gallon ATV Spot Sprayer
Roundup Ready!
16 gallon poly tank, 2.2 GPM Northstar
pump, 60 PSI. 15’x3/8” hose & wand with
adjustable spray pattern. Tie down straps
included.
GPM 26810011 • 25 lbs.
Order Online!
26 gallon sprayer
26 Gallon ATV Spot Sprayer
26 gallon poly tank. Equipped as GPM
26810011
GPM 2681201 • 27 lbs.
ATV Broadcast kit
(not pictured) 14’ spray pattern with just one
nozzle. Mounts to ATV hitch.
GPM 268195 • 10 lbs.
Tree SPRAYERS
High pressures allow higher spray heights &
atomized mist for delicate flowers. Reaches
small isolated areas that are difficult to treat.
ATV and tow behind models.
16 Gallon ATV Tree Sprayer
16 gallon poly tank. 12V, 2 GPM, 200 PSI
Pumptec pump. 35’x3/8” hose with spray
gun. Sprays up to 30’.
GPM 282795 • 30 lbs.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
83
BACKPACK SPRAYERS / CF VALVES
12 VOLT
® SRS-600 PROPACK™ ELECTRIC
The electric SRS600
SPRAYER
offers convenience,
BACKPACK SPRAYER
The advanced design of this simple, highly functional unit
makes it very light. It has fewer parts since many components
are built-in. This makes it highly durable and a guaranteed
product, and at the same time ensures maximum economy.
• Mechanical agitation keeps wettable powders in suspension
• Internal tank reinforcement via ribbing between the walls
makes the unit stronger and more deformation-resistant
• Has a handle for transport. 4 gallon tank.
• Reversible
TRu Star-16-green • 7 lbs.
INTERNAL PuMP BACKPACK
SPRAYER W/ PADDLE AgITATION
• Piston pump contained within tank,
eliminates leakage on operator
• 4 gallon tank
• Right-hand or left-hand operation
• Internal mechanical agitator for constant
mixing
• Large fill opening and deep strainer
• Polypropylene UV resistant tank.
• Built-in handle: carry or hang / store
• Ergonomic shape for maximum comfort.
• Stainless steel spray lance
• 8.2 lbs.
jAC HD400
jACTO ELECTRIC BACKPACK
SPRAYER
“The most advanced Backpack Sprayer in
the World”
• 4 gallon tank
• Constant Pressure
• Five level pressure control
• Walking pace indicator
• Battery charge level display
• Auto shutdown when not in use
• Hydraulic agitation
• Internal filter
• Removable battery
for easy charge
• 8.4 lbs.
jAC PjB-16
versatility, and
comfort in a back
pack sprayer. It
eliminates the
need to keep
“Pumping Up” the
sprayer to maintain
a steady spray
pattern, making
spraying faster and
easier. It works well
with many materials
including herbicides,
insecticides and
anti-icing liquids.
Features:
• Spray up to 120 gallons on one
charge
• High performance chemical resistant
SHURflo pump
• Variable speed and adjustable nozzle
• Ultra comfortable ergonomic design, full
back pad, thickly padded shoulder harness
• Adjustable spray tip: uniform cone pattern
• Heavy duty hand lever locks in the
open position, reduces operator fatigue
• 24” spray lance
• 4 gallon polyethylene tank
HYP SRS-600 - 12 volt sprayer 15 lbs.
HYP 94-536-00 - Battery Pack Only
HANDHELD
SPRAYER
Polypropylene design.
Working pressure:
60 psi.
Tank capacity:
48 oz.
TRu P-50-Y • 1.6 lbs.
CFVALVE™ : CONSTANT FLOW VALVE
Spray the precise amount of chemical with the addition of a
CFValve™ to the delivery system of a backpack, hand held,
compression, 12V or field sprayer. Both the flow and pressure are
Use YELLOW & RED valves in backpack and compression sprayers.
84
controlled, and the flow is shut off when the pressure drops below the
pre-set feature of the valve. The valve must be ordered by thread size
and pressure range. Weight= .1 lb. each.
SEE CHART BELOW FOR THREAD & PRESSuRE RANgE.
Use GREEN & BLUE valves in 12V/ on-demand systems, boom sprayers or engine driven pumps
Back Pack
Sprayer Model
YELLOW
14.5 PSI
RED
21 PSI
BLUE
29 PSI
GREEN
43.5 PSI
Solo, Lesco,
any 3/8 BSP thread
Y3-8BSPV
R3-8BSPV
B3-8BSPV
G3-8BSPV
Hudson, Jacto, SP,
any Spraying Systems
component thread
Y11-16SYV
R11-16SYV
B11-16SYV
G11-16SYV
Field King, Hardi,
Maruyama
Y18MMV
R18MMV
B18MMV
G18MMV
Chapin, Birchmeier,
B&G
Y1-4NPTV
R1-4NPTV
B1-4NPTV
G1-4NPTV
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
SOLO BACKPACK SPRAYERS
Knapsack Sprayers
• UV resistant, high density
polyethylene tanks, commercial
grade wands, nozzles, hoses, valves
• Chemical resistant Viton®seals.
• Pump on the go feature: pump
while on your back
• 4 nozzle assortment
• Left or right hand pump handle.
4 gallon piston pump
SOL 425
5 gallon piston pump
SOL 435
4 gallon diaphragm pump
SOL 475B
piston pump
3 gallon diaphragm pump
SOL 473D
Part #
SOL 485
diaphragm pump
3 gallon piston pump
SOL 473P
Common parts and accessories
Description
Fits
SOL 0610406-K
SOL 0610407-K SOL 0610410-P SOL 4800170
SOL 4900170N SOL 4900356
SOL 4900405-K SOL 4900421
SOL 4900430
SOL 4900527
SOL 4900528
SOL 4900626
5 gallon diaphragm pump
Diaphragm Pump Repair Kit
475, 485, 473D
Piston Pump Repair Kit
Brass Adjustable Nozzle Kit Shut-off Valve
28” Universal Wand Assembly Pressure Gauge
Pump Repair Kit
20” Brass Wand
Drift Guard
Plastic Adjustable Nozzle
60” Brass Wand
Pro-Spot Drift Guard
425, 435, 473P
All
All
All
All
454, 456, 457
All
All
All
All
All
SOL 425 - 4 gallon piston pump,
90 PSI. 11 lbs.
SOL 425DLX - 4 gallon piston pump
deluxe package w/ folding handle,
pressure gauge, relief valve in tank
and brass adjustable nozzle. 11 lbs.
SOL 435 - 5 gallon piston pump.
14 lbs.
SOL 475B - 4 gallon diaphragm
pump, 60 PSI. 11 lbs.
SOL 475BDLX - 4 gallon diaphragm
pump and same features as 425DLX.
11 lbs.
SOL 485 - 5 gallon diaphragm pump.
14 lbs.
SOL 473D - 3 gallon diaphragm
pump. 11 lbs.
SOL 473P - 3 gallon piston pump.
11 lbs.
Compression Style Sprayers
• High capacity pump - quick
pressurization
• Large 2nd opening for
cleaning
• 48” hose and 28” wand
SOL 430-1G
1 gallon • 3 lbs.
• Pressure relief valve
• Easy fill funnel top
• 4 nozzle assortment
SOL 430-2G
2 gallon • 4 lbs.
451 Motorized Backpack Mist Blower
The 66.5cc engine with nickle/silicon carbide cylinder coating offers increased
performance.
Along with the high output 824 CFM fan, this powerful backpack sprayer
gives higher misting performance for total plant penetration. 38’ application
range.
Large 0.5 gallon capacity fuel tank combined with low fuel consumption
allows long operating periods (more than 80 minutes without refueling).
SOL 430-3G
3 gallon • 5 lbs.
Over 50 years
of SELLING
motorized
backpack
sprayers
QUIET! Low dB(A) rating. Compact size and lightweight
SOL 451 • 24 lbs.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
85
12V PUMPS / WEED WIPERS
B
C
A
• Premium quality on-demand pumps for
spot or broadcast spraying
• 100% continuous duty rating
• Honeywell Micro Switch™ for
durable automatic shutoff
• Chemical-resistant Viton® valves for
better performance and long life
A. gPM 2682271
2.2 GPM/70 PSI, 3/8” NPT ports
B. gPM 2683061
3.0 GPM/60 PSI, 1/2” NPT ports
B. gPM 2684061
4.0 GPM/60 PSI, 1/2” NPT ports
B. gPM 2685561
5.5 GPM/60 PSI, 1/2” NPT ports
C. gPM 2687061
7.0 GPM/60 PSI 1/2” NPT Ports
®
removable guard
for use when under
desired plants
reversible clear
plastic elbow for
180° rotation of pad
1/2” polynap
reservoir handle - 1 quart, 52” long
NSQ SERIES 12V ON-DEMAND
DIAPHRAgM PuMPS
SIDESWIPE
SHURFLO PUMPS
HYP 8000-541-236
Lawn & garden. 12v, 1.0 GPM, 60 psi
demand switch, 3/8” NPTF ports
CYLINDRICAL WEED SPONGE
No dripping or drift! Many models & sizes!
Each Super Sponge® comes with:
• Heavy-duty, steel frame
• Corrosion-resistant plumbing
• Protective netting for the sponges
• Tank shut-off & stainless steel filter screen
• Translucent tank
• Sight glass manifolds allow precise
flow metering
HYP 8000-543-236
Standard. 12v, 1.8 GPM, 60 psi demand
switch, 3/8” NPTF ports
HYP 2088-313-145
Standard. 12v DC, 3.6 GPM, open flow (2.6
GPM@40 psi) 45 psi demand switch, 1/2”
MSPT ports.
HYP 2088-394-144
Standard w/ 6’ power cord, 115 V AC, 7
amps, 3.0 GPM, 45 psi demand switch, 1/2”
MSPT ports.
HYP 4211-035
Power twin, 12 v DC,
8.7 Amps, 6.25 GPM open flow (3.5
GPM@40 psi) demand switch, 1/2” MPT
ports.
HYP 8000-543-220
Standard bypass. 1.5 GPM open flow, 60 psi
internal bypass 3/8” NPTF ports.
SuPER SPONgE KITS
®
Each kit comes complete with plumbing,
sponges and tank. All you supply are the
wheels and frame! 5’, 10’ and 15’ sizes.
86
HYP 8030-813-239
High pressure. 1.6 GPM open flow, (.83 GPM
@ 150 psi) demand switch, 3/8” NPTF ports.
See fittings for 2088 & 4211 Pumps at right
The original handheld herbicide
wipe-on applicator: easier than
hoeing, safer than spraying.
Designed to apply systemic
herbicides only where you need
them: on the weeds. Sideswipe’s™
patented design delivers just
enough chemical to do the job.
Whether you are a professional
grower or a weekend gardener,
Sideswipe™ has a place in your
weed control program. Its many
unique features make it superior
to competitive applicators:
• No drift - usable on a windy day
• No leaching
• Nylon nap pad wets evenly
• All parts replaceable
• Nose threaded fitting to insert shutoff valve
• Reversible clear plastic elbow indicates
fluid level & gives 180° rotation of pad for
new wiping area & longer pad life
• Not for use with oil based products.
SID TH-S-100 - 9” Sideswipe • 1.4 lbs.
SID TH-104 - 9” replacement pad • .5 lbs.
®
Fittings for 2088 and 4211 Series Pumps
(shown at left)
90° SWIVEL PuMP FITTINgS
HYP 234-3916 - 1/2 FPTx3/8 Barb
HYP 234-3926 - 1/2 FPTx1/2 Barb
HYP 234-3936 - 1/2 FPTx5/8 Barb
HYP 234-3946 - 1/2 FPTx3/4 Barb
STRAIgHT SWIVEL PuMP
FITTINgS
HYP 234-2916 - 1/2 FPTx3/8 Barb
HYP 234-2926 - 1/2 FPTx1/2 Barb
HYP 234-2936 - 1/2 FPTx5/8 Barb
HYP 234-2946 - 1/2 FPTx3/4 Barb
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
INSTRUMENTS / CALIBRATORS
LA CROSSE®
WIRELESS TEMPERATuRE
STATION
Magnifiers
OPTIVISOR
Optical glass, binocular-magnifier. Lightweight,
durable w/ adjustable headband. Supplied with
#10 lens plate which magnifies 31/2X at a focal
length of 4”. Optional
OptiLoupe increases
to 2-1/2X the power.
DON DA10 Optivisor • .75 lb.
DON LP1OptiLoupe • 4 oz.
Min/max records for temperature with
date/time stamp. Atomic time & date set
automatically. Includes one remote sensor
but can receive up to three. Outdoor temp.
range: -39.8° F to 157.8° F. Indoor temp.
range: 32° F to 139.8° F. Transmission
range: up to 330’. Base unit
requires 2 AAA batteries.
Transmitter requires
4 AAA batteries.
(batteries are not included)
LAC WS-9080U-IT
DONEGAN OPTICAL
MAGNIfIERS
additional
sensor:
Folding pocket
magnifier with multiple
lenses in plastic case.
Dual lens model
produces 3 magnifying
strengths: 4X, 5X & 9X.
DON P949 • 2 oz.
SC1 SPRAYER CALIBRATOR
CODDINGTON
MAGNIfIER
Double lenses mounted in
chrome plated case. 23mm
lens, 10X magnification.
DON V309-23 • 2 oz.
WATER SENSITIVE PAPER
Specialty coated papers for evaluating
distributions, swath widths, droplet densities
& penetration of spray into the crop canopy.
Yellow water sensitive paper will stain blue
when exposed to aqueous spray droplets.
ask for information sheet 20367.
Avoid over or under application of
chemicals.
• Quickly find worn spray nozzle tips Industry guidelines recommend tip replacement once flow rate is 10% greater
than a new tip.
• Accurately measure true tip flow rate High tech sprayers can only be properly calibrated and confirmed with this information.
• Fast and simple operation- Readings in 10 seconds or less per trip.
• Easy to read digital GPM display.
• Batteries included
SPO 23890 • .52 lbs.
SPRAYER
CALIBRATION
CONTAINER
2 Liter capacity.
SSC CP24034A-PP
TEEjET® TIP
CLEANING BRuSH
SSC CP20016-NY
Water Sensitive Paper
Part No.
SSC 20301-1N
SSC 20301-2N
SSC 20301-3N
Paper Size
Package
3”X1”
3”X2”
20”X1”
50 cards
50 cards
25 strips
INCIDE OuT SPRAY TANk
CLEANER
LAC TX29U-IT
WIRELESS RAIN
CENTER
Self-emptying rain
bucket - empties via
internal tilting cups.
Measures total
rainfall, & past 24
hours rainfall.
Light-heavy rainfall
indicator icons & rain
alarm. Transmits up to
330’. Requires 4 AAA
batteries (not included).
LAC WS-9005T-IT-CBP
HANDHELD ANEMOMETER
Measures Wind Speed
Registers maximum & average
wind speed. Displays wind chill
and temperature in °F or °C. Will
show wind speed of .44 mph
to 67 mph. Back lit with battery
saving auto off. Neck band and
battery included.
LAC EA-3010
TeeJet® and OESCO, INC.
Leaders in Spray Application Supplies
Some Nozzles We Recommend for specific Spraying Applications:
Soil incorporation, pre-emergence, fertilizer (broadcast)
Use a coarse spray from Turbo Floodjet®and TurboTeeJet®induction nozzles.
Systemic herbicides, fungicides, insecticides
Use the same nozzles plus the TurboTeeJet®, AIXR and AIC nozzles.
Contact herbicides, fungicides, insecticides
Use Turbo Teejet®or XR Teejet®
Liquid spray tank cleaner emulsifies pesticide
residues & bonds them to rinse solution for a
more thorough cleanout of sprayer systems.
• Manufacturer approved
• Eliminates unwanted pesticide residues
from sprayer system
• Reduces risk of damage to non-target
plants
• Won’t clog nozzles or damage pumps
• Low use rate
PLI 434-32 - 1 quart container
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
87
FLOW METERS / CONTROLS
POLMAC CONTROL
uNITS
These units have been
designed & manufactured
with special materials suitable for
any application in the field of crop
spraying and protection. The nylon
and stainless steel components are
highly practical, corrosion-proof and
resist the corrosive action of sprayed
chemicals and liquid fertilizers.
Contact us for
sizing to your
sprayer.
4 Valve Controller
with unloading relief
valve & gauge.
POL 00280004
PONY FLOW 4
PLuS 12 V
Cab mount displays
for flow meters. Many
options available.
Features flow rates &
totals, ground speed,
pressure, and/or
control of 12V DC
motor drive valve.
Call for application &
part numbers.
Aluminum turbine meter with LCD readout
for gallons with 1” NPT threads. 0.3-3 GPM.
Field replaceable batteries. Factory & field
calibration. 300 PSI max.
gPI 113900-9500 • 2 lbs.
PRO-FLOW
This is a 1 1/2” or 2” (9 to
90 gpm), 250 psi maximum,
programmable stop flow meter.
The operator
programs the
set amount,
manually
opens the
valve, & when
the set amount
is reached
the valve
automatically
closes. Comes as
compact (Pro-Flow 1)
or remote (Pro-Flow 2). Great for filling spray
tanks.
Pro-Flow 1
Part #
(A) Signal (B) Signal
1 1/2”
12 Vcc.
0 Vcc.
POL 00379007
2”
12 Vcc.
0 Vcc.
POL 003790g2
Pro-Flow 2
4 Valve Controller with
unloading relief valve, bypass
metering valve & gauge.
POL 00304304
ELECTRONIC
DIGITAL METERS
Aluminum turbine meter with LCD readout
for gallons with 1” NPT threads. 3-50 GPM.
Field replaceable batteries. Factory & field
calibration. 300 PSI max.
gPI 113900-9501 • 2 lbs.
Nylon turbine meter for 0.3-3 GPM. LCD
readout. Field replaceable batteries. Factory
& field calibration. 1” NPT. 150 PSI max.
gPI 113900-9510 • 1 lb.
Nylon turbine meter for 3-50 GPM. LCD
readout. Field replaceable batteries. Factory
& field calibration. 1” NPT, 150 PSI max.
gPI 113900-9511 • 1 lb.
Stainless steel turbine meter for 3-50 GPM.
LCD readout. Field replaceable batteries.
Factory & field calibration. 1” NPT, 800 PSI
max.
gPI g2S10N09gMA • 7 lbs.
Part #
(A) Signal (B) Signal
1 1/2”
12 Vcc.
0 Vcc.
POL 00379010
2”
12 Vcc.
0 Vcc.
POL 003790g3
(A) - Output signal with throttle valve open
(B) - Output signal with throttle valve closed
NOzzLES FOR
WASHINg CONTAINERS
Used to clean chemical
(1)
(2)
products out of emptied
containers before they are
disposed. Fluid activated nozzle
rotates on a central shaft.
Nozzle rotates 360° to spray the
inner surfaces of the container.
POL 63408499 - Rotating Extractable (1)
POL 6340849S - Slim Rotating Extractable (2)
PONY FLOW 4
9V SENSOR/COuNTER
For use with Polmac flow meters. Can be
mounted directly to body of the flow meter or
remotely mounted. Functions include Start,
Stop, Auto On, Auto Off, Running Total and
Final Total. Measures in US gallons, Imperial
gallons or liters. Up to 99,999,999 units.
Model
Order #
NOzzLES FOR WASHINg TANKS
To clean chemical products out of tanks
& mixers. Its fluid activated rotating head
covers 360° & performs a complete wash. It
delivers 7.4 gallons per minute at 70 PSI.
POL 63408399 POL 6340839R
CALC-AN-ACRE®II SPEED &
ACREAgE MONITOR
Digital speedometer & acreage counter.
12V operation from the vehicle battery,
magnetic wheel or drive shaft pickup. Holds
two acreage counts in memory. Measures
speed, area & distance. Includes console,
speed sensor & installation hardware &
instructions. MIC 01000 - Calc-an-acre II
Flow Meter
Sensor
Pony Flow 4
POL CH370001 ST. 1/2”-3/4” INOX - 1/2’ NYLON
30306032.CDE
Pony Flow 4C
POL CH37000C
Pony Flow
4 Remote
88
POL CHRE0001
STANDARD >3/4”
30306032.DEU
RAPID CHECK
41308899.DEU
VISIT WWW.OESCOINC.COM
GET MORE INFORMATION.
ORDER ONLINE!
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
SNYDER TANKS
THERE’S juST NO SuBSTITuTE fOR SNYDER TANkS.
HIGH DENSITY, ROTO MOLDED POLY TANkS
POTABLE WATER • CHEMICALS • SAP • CIDER • fERTILIzERS
Some of our more popular stock items below. Contact us for a complete catalog of all SYNDER products
MADE IN THE
PCO TANKS
PART #
GALLONS
OUTLET SPECS
DIAMETER
HEIGHT
LENGTH
TAN 109137
30 gallon
U
19”
22-1/2”
24-1/2”
TAN 117137
50 gallon
U
19”
22-1/2”
38”
TAN 120137
100 gallon
U
30”
31”
38”
TAN 157137
150 gallon
U
36”
29”
48”
TAN 166137
200 gallon
U
36”
39-1/2”
48-1/2”
TAN 172137
300 gallon
U
38”
36-3/4”
69”
LEG TANKS
GALLONS
OUTLET SPECS
DIAMETER
HEIGHT
LENGTH
TAN 10837
PART #
30 gallon
G
23”
25-3/4”
19-1/2”
TAN 10637
A
23”
25-3/4”
38”
TAN 11237
60 gallon
125 gallon
S
30”
34-1/2”
50”
TAN 12837
230 gallon
S
38”
42-1/2”
52”
TAN 13237
300 gallon
S
38”
42-1/2”
72”
TAN 14037
525 gallon
E
48”
52-1/2”
75”
TAN 13637
730 gallon
E
57-1/2”
57-1/2”
80”
VERTICAL TANKS
GALLONS
OUTLET SPECS
DIAMETER
HEIGHT
TAN 18237
PART #
550 gallon
N1
64”
46”
TAN 18037
N1
48”
74”
TAN 18337
550 gallon
1100 gallon
64”
90”
TAN 17137
1100 gallon
N2
I
86”
56”
TAN 17737
1500 gallon
I
86”
73”
TAN 741018
3000 gallon
N2
102”
97”
HORIZONTAL TANKS
PART #
TAN 10337
TAN 10537
TAN 11137
TAN 11337
TAN 11537
TAN 12337
TAN 12537
GALLONS
25 gallon
55 gallon
110 gallon
150 gallon
150 gallon
200 gallon
200 gallon
OUTLET SPECS
A
A
C
C
C
C
C
Snyder Standard Bulkhead
Fittings (With EPDM gaskets)
TAN 34300005
TAN 34300006
TAN 34300003
TAN 34300008
3/4”
1”
1 1/4”
1 1/2”
• 3 oz.
• 3 oz.
• 3 oz.
• 3 oz.
IBC Tank Access Adapter
2” Buttress x 2” Male NPT threads
with Santoprene gasket
BJO TA283 • 2 oz.
DIAMETER
23”
23”
30”
30”
32”
32”
38”
HEIGHT
26-3/4”
38-1/4”
49-3/4”
34-3/4”
36-1/2”
36-1/2”
40-1/2”
LENGTH
19”
38”
50”
60”
56”
71”
52”
• Molded-in gallonage markers (indicators)
• Flat spots on each for easy agitation
• Design requires no additional support or banding
• UV inhibitors molded in for longer tank life
• Molded-in gallonage markers (indicators)
• Free standing HLT needs no cradles for support
• Ribbed for strength with built-in supports
• UV inhibitors molded in for longer tank life
• Heavy duty bolted fittings standard on 550+
gallon reduces loosening of fittings in use
• Fitting compatible siphon tubes to allow bottom
to fill of tank
• Molded-in tie downs for securing and lift lugs for
easy movement
• UV inhibitors molded in for longer tank life
OUTLETS
A =
C =
U =
E =
N2=
N1 =
G=
S=
I =
6” fill, one 3/4” outlet with anti-vortex
10” fill, two 1-1/4” outlet (1 with anti-vortex)
No holes or fittings, Fittings can be ordered separately
10” fill, one 2” HD outlet with siphon
18” manway, one 2” bolted outlet with siphon
18” manway, one 2” HD outlet with siphon
6” cap, no outlet
10” fill, one 1 1/4” outlet
10” fill, one 2” bolted outlet with siphon tube
• 10” threaded cap for easy filling
• Molded-in gallonage markers (indicators)
• Center sumps and end flat spots
• UV inhibitors molded in for longer tank life
• Cradles required for support
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
89
PUMPS / COUPLERS
®
WP-1000 PORTABLE PuMP
Good for tank filling, maple sap, garden or
small plot irrigation.
• Echo 21.2 cc engine, Pro-Fire™ Electronic
Ignition
• Cast iron volute
• Ideal for around-home use: draining pools,
pool covers, irrigating lawns & gardens
• Discharges up to 28 gal/min., 1680 gal/hr
• Unit complete with suction hose & strainer
ECH WP-1000 • 11.9 lbs.
2” SELF-PRIMINg
POLYPROPYLENE TRANSFER
PuMP
With 5 vane impeller, powered by 6.5 HP
PowerPro gas engine with low oil sensor.
150 GPM - max. HYP 1542P-65SP • 49 lbs.
2” SELF-PRIMINg ALuMINuM
TRANSFER PuMP
Powered by a 4 HP Honda. GX120 gas
engine w/ oil alert. Mounted in protective
cage. 145 GPM - max.
HYP 1572-SPX • 55 lbs.
MYERS | DU-ALL
PISTON PuMPS
FMC/jOHN BEAN PISTON PuMPS
These pumps were made under the 2 names
of FMC and Bean. We service, sell & stock
parts for these pumps, old & new models.
SALES, SERVICE & PARTS available for
FMC/john Bean Pumps
SALES, SERVICE & PARTS available for
old and new Myers pumps
FRAME
MOuNTED
CENTRIFugAL PuMPS
Special models available. ALL parts
available for ACE pumps. Contact us for
specifications on pumps.
Cast iron,1 1/2” suction x1 1/4” discharge,
clockwise rotation. ACE FMC-CW-150
Cast iron, 2” suction x1-1/2” discharge,
clockwise rotation. ACE FMC-CW-200
Cast iron,1 1/4” suction x1” discharge, counterclockwise rotation. ACE FMC
Cast iron,1 1/2” suction x1 1/4” discharge,
counter-clockwise rotation. ACE FMC-150
Cast iron, 2” suction x1 1/2” discharge,
counter-clockwise rotation. ACE FMC-200
Call for other model number specifications
2” PuMP HOSE
COMBO KIT
Includes suction strainer,
Two 2” nipples, a 2” x 20’
suction hose and a 2” x
25’ discharge hose. Tough
PVC hoses have male &
female standard pipe thread couplings.
gPM 108999• 27 lbs.
PuMP ADAPTERS
Solid Steel Push Pin Design
DIAPHRAgM &
PLuNgER PuMPS
SALES, SERVICE &
PARTS available
DIAPHRAgM & PLuNgER PuMPS
SALES, SERVICE & PARTS available
®
PuMP COuPLERS:
QuICK COuPLERS
(Female to Female)
HYP 1323-0072- 1 3/8” PTO - 6 spline (I.D.),
15/16” Pump end (I.D.) forged steel, 540 RPM
HYP 1323-0073- 1 3/8” PTO - 21 spline (I.D.),
15/16” Pump end (I.D.) forged steel,1000 RPM
HYP 1323-0074- 1 3/8” PTO - 6 spline (I.D.),
5/8” Pump end (I.D.) forged steel, 540 RPM
HYP 1323-0075- 1 3/8” PTO - 21 spline (I.D.),
5/8” Pump end (I.D.) forged steel, 1000 RPM
90
Stock
Number
Spline Round Keyway Wt.
Size Lbs.
Bore Bore
gAg 114-1000 1 3/8x6
5/8
gAg 114-1200 1 3/8x6
3/4
gAg 114-1400 1 3/8x6
7/8
gAg 114-1500 1 3/8x6
15/16
1/4
1.94
gAg 114-1600 1 3/8x6
1
1/4
2.00
3/16
2.13
3/16
2.07
3/16 & 2.00
1/4
We service most models
of commercial
and agricultural spray
pumps.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
HYPRO PUMPS
MAX RPM
1200
SHAFT INPuT
5/8” solid shaft
HYP 6500N
21.8
300
1200
5/8” solid shaft
HYP 6500XL
21.8
300
1200
5/8” solid shaft
HYP 7560C
22.5
300
1200
15/16” solid shaft
HYP 7560N
22.5
300
1200
15/16” solid shaft
HYP 7560XL
22.5
300
1200
15/16” solid shaft
HYP 4001C
9.1
150
1800
5/8” solid shaft
HYP 4001N
9.1
150
1800
5/8” solid shaft
HYP 4001XL
9.1
150
1800
5/8” solid shaft
MODEL
MAX gPM MAX PSI
1.5
500
HYP 5315C-X
MAX RPM
1800
SHAFT INPuT
5/8” OD solid shaft
®
HYP 5320C-X
2.2
500
1800
5/8” OD solid shaft
HYP 5325C-X
2.5
500
1800
5/8” OD solid shaft
HYP 5330C-X
3
500
1800
5/8” OD solid shaft
HYP 5315C-HX
1.5
500
1800
5/8” ID hollow shaft
HYP 5320C-HX
2.2
500
1800
5/8” ID hollow shaft
HYP 5325C-HX
2.5
500
1800
5/8” ID hollow shaft
HYP 5330C-HX
3
500
1800
5/8” ID hollow shaft
HYP 5206C
8
400
800
1” solid shaft w/base
1 3/8” hollow shaft w/base
HYP 5206C-H
8
400
800
HYP 5210C
10
400
600
1” solid shaft w/base
HYP 5210C-H
10
500
600
1-3/8” hollow shaft w/base
OESCO, Inc. is the
Northeast Distributor for Hypro
Call one of our pump specialists for
your parts & service needs.
MAX RPM
PORT SIzE
SHAFT INPuT
HYP 9910-D252
6.1
290
650
1-1/4” HB inlet, 1” HB outlet
3/4” solid keyed shaft
HYP 9910-D252gRgI
6.1
290
2800
3/4” HB inlet, 3/8” HB outlet
3/4” hollow shaft
HYP 9910-D252gRgI58
5.5
290
3600
3/4” HB inlet, 3/8” HB outlet
5/8” hollow shaft
MAX gPM MAX PSI
MODEL
HYP 9910-D30
MAX gPM MAX PSI MAX RPM
9
550
580
HYP 9910-D30APA
9
580
HYP 9910-D50
14
580
HYP 9910-D50B
HYP 9910-D115
HYP 9910-D135
MODEL
Select Kit
Select Kit
Assembled w/ gearbox 9910-KIT1640 and control
9910-GS40GI for mounting on 5HP gas engine
3600
550
MAX gPM MAX PSI
Same pump as 9910-D50 w/solid thru shaft
MAX RPM
PORT SIzE
Select Kit
Select Kit
Select Kit
1-1/4” HB inlet, 1/2” HB outlet
Same pump as 9910-D50 w/Buna-N diaphragms
HYP 9910-D50APA
HYP 9910-D70
SHAFT INPUT
1-1/4” HB inlet, 1” HB outlet
Same pump as 9910-D30 with 3/4” solid thru shaft
HYP 9910-D30gRgI
MODEL
PORT SIzE
Select Kit
SHAFT INPuT
19
290
550
1-1/4” HB inlet, 1” HB outlet Select shaft kit for desired drive
30.1
290
550
1-1/2” HB inlet, 1” HB outlet Select shaft kit for desired drive
290
34.8
550
MAX gPM MAX PSI MAX RPM
1-1/2” HB inlet, 1” HB outlet 1-3/8” — 6 splined male shaft
PORT SIzE
SHAFT INPuT
HYP 9910-DBS140
37.8
725
550
HYP 9910-DBS160
39.6
725
550
HYP 9910-DBS200
49.7
725
550
MODEL
MAX gPM
MAX PSI
MAX RPM
SHAFT OuTPuT
HYP 9202C
103
170
6000
5/8” solid shaft
HYP 9203C
140
170
6000
5/8” solid shaft
HYP 9202S
103
170
6000
5/8” stainless steel shaft
HYP 9203S
MODEL
140
170
6000
5/8” stainless steel shaft
MAX gPM
MAX PSI
MAX RPM
PTO OuTPuT
HYP 9402C-540
76
95
600
1-3/8” female, 6-spline shaft
1-1/2” HB inlet,
3/4” NPT outlet
1-3/8” — 6 splined male
double-ended shaft
HYP 9402C-540Q
76
95
600
1-3/8”, 6-spline Quick Coupler
HYP 9403C-540Q
140
104
600
1-3/8”, 6-spline Quick Coupler
HYP 9403C-1000
140
104
1000
1-3/8” female, 21-spline shaft
CENTRIFugAL PuMPS
MODEL
DIAPHRAgM PuMPS
MAX PSI
300
ROLLER PuMPS
MAX gPM
21.8
PISTON PuMPS
MODEL
HYP 6500C
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
91
RELIEF / CONTROL VALVES
PRESSuRE RELIEF / REguLATINg VALVES
Model 6815
PISTON TYPE
MODEL 6815
• Brass with stainless
steel springs
• Models with light spring
(50psi) for use with
XR TeeJet® and LP
TeeJet®tips and other
low pressure systems
• Use HSS models for
longer lasting valve
Model 8460
Valve #
Recommended
Pressure Range
SSC 6815-1/2-50
Up to 50 psi
SSC 6815-1/2-300
Up to 300 psi
SSC 6815-1/2-700
300 - 700 psi
SSC 6815-3/4-50
Up to 50 psi
SSC 6815-3/4-300
Up to 300 psi
SSC 6815-3/4-700
300 - 700 psi
SSC 6815-1/2-HSS-300
Up to 300 psi
SSC 6815-1/2-HSS-700
300 - 700 psi
SSC 6815-3/4-HSS-300
Up to 300 psi
SSC 6815-3/4-HSS-700
300 - 700 psi
DIAPHRAgM TYPE
MODEL 8460
Nylon inlet body w/ aluminum
bonnet. 1/2” or 3/4” NPT (M) inlet
and (F) outlet connections. Flow
rates to 70 GPM for 3/4” size.
Pressures to 50 & 300 psi.
Model 23120
MODEL 23120A
Same as 23120 but with 316SS
spring and Viton O-ring
1/2” NPT
3/4” NPT
1 1/4 lbs.
1/2” NPT
3/4” NPT
SSC 8460-1/2-50
1/2” NPT
Up to 50 psi
Net
Weight
14 oz.
SSC 8460-3/4-50
3/4” NPT
Up to 50 psi
14 oz.
SSC 8460-1/2
1/2” NPT
Up to 300 psi
14 oz.
SSC 8460-3/4
3/4” NPT
Up to 300 psi
14 oz.
Valve #
Inlet & Outlet
Pipe Connection Sizes
MODEL 23120
302 stainless steel spring and
EPDM O-ring. Excellent chemical
resistance. 1/4” port for pressure
gauge pipe plug included.
Polypropylene.
Inlet & Outlet
Net
Pipe Connection Size Weight
Valve #
Rec. Pressure
Range
* Inlet & Outlet
Pipe Connection Sizes
Pressure
Range
Net
Weight
SSC 23120-*-PP
1/2” or 3/4”
150 PSI (10 bar)
8 oz.
SSC 23120A-*-PP
1/2” or 3/4”
150 PSI (10 bar)
8 oz.
also aVailaBle as special orDer - moDels for high pressures up to 1200 psi
AA17 TEEVALVE® CONTROL
VALVE
6B DIRECTOVALVE®
• Molded of corrosion-resistant
materials, all wetted parts are
polypropylene, stainless steel
and polyethylene
• Maximum pressure:150 PSI
• Large capacity, 12 GPM @
5 PSI pressure drop
• Molded-in mounting flange and
1/4” NPT gauge port
• 3/4” inlet 1/2” boom connection
SSC AA6B • 8 oz.
• Raise lever to
open, lower to close
• Aluminum construction
with corrosion resistant
internal parts
• Lift off poppet valves for positive ON-OFF
action
• Cam type index tip assures exact position
of valve
• Dimensions: 4” wide x 4 1/2” high x 5” deep
(not including handle)
MODEL 17L
HAMILTON BYPASS
AND RELIEF VALVES
Connections:
• 1/4” NPT pressure gauge port
• Inlet: 3/4” NPT
• Boom outlets: 3/4” NPT (3)
• Accessory outlets 3/4” NPT (2)
SSC AA17L • 2.8 lbs.
Compact brass valve has spring
and stainless steel ball for valve.
Tee handle with locking nut
to set pressure. Available in
1/2” and 3/4” MPT and spring
range 0 - 300 PSI or 0 - 600
PSI. Bypass connector 1/2 or
3/4” FPT.
MODEL 17Y
HAM 2041-01 • 1/2” NPT, 0-600 PSI
HAM 2042-01 • 1/2” NPT, 0-300 PSI
HAM 2053-01 • 3/4” NPT, 0-300 PSI
HAM 2054-01 • 3/4” NPT, 0-600 PSI
92
• 1 lb.
• 1 lb.
• 1 lb.
• 1 lb.
Connections:
• 1/4” NPT pressure gauge port
• Inlet: 1” NPT
• Boom outlets: 3/4” NPT (3)
• Accessory outlets: 3/4” NPT (2)
SSC AA17Y • 2.8 lbs.
HIgH PRESSuRE &
HIgH FLOW VALVES
jBS 1207620
50-800 psi, 40 GPM Capacity
3/4” Threads
Height: 9 1/2”
Weight: 8 lbs.
jBS 5284450
50-1200 psi, 75 GPM Capacity
1 1/4” Threads
Height: 12 1/8”
Weight: 10.5 lbs.
ALL PARTS
AVAILABLE FOR
JOHN BEAN VALVES
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
ELECTRIC / MANUAL VALVES
Plastic Valves & Fittings
PVC molded-in place ball valves. Low cost, quarter-turn operation.
Maintenance free, corrosion-free. Used with water plumbing for
industrial, agricultural and residential (NSF Approved) purposes.
Can also be used in the chemical supply line for waste water
treatment as well as chemical plants.
PART #
NPT SIZE
FLO 6Q-MTWE050
1/2” FNPT
FLO 6Q-MTWE075
3/4” FNPT
FLO 6Q-MTWE100 1” FNPT
FLO 6Q-MTWE125
1 1/4” FNPT
FLO 6Q-MTWE150
1 1/2” FNPT
FLO 6Q-MTWE200
2” FNPT
PLASTIC BALL VALVES
SERIES 226
QuICk OPEN SELf CLOSE VALVES
Normally closed. Quick open, self closing valve, heavy
brass construction. Stem design has pressure equalization
across stem seat for high pressure operation. Disc seat
KINGSTON
and O-ring seals w/ stainless steel springs. Max. presure
400 PSI. Handles available with squeeze, pull, or lift levers (also
available without lever and bracket.) Excellent for agricultural or
industrial sprayers. 1/2”, 3/4”, 1”, and 1 1/4” sizes.
UP to 150 PSI - squeeze lever
KIN 305A-4-1 1/2” • 2 lbs.
KIN 305A-5-1 3/4” • 2.5 lbs.
Above 150 PSI - squeeze lever
KIN 305B-4-1 1/2” • .5 lb.
KIN 305B-5-1 3/4” • .75 lb.
KIN 305B-FF-5-KIT - Kit for 3/4” high pressure valve
KIN 305A-FF-5-KIT - Kit for 3/4” low pressure valve
Call for information on other sizes and handle styles
3 way Valves
Barb x Barb
MODEL
END CONN.
END CONN.
SMC FN-226-4B4B-E
SMC FN-226-6B6B-B
SMC FN-226-8B8B-B
1/4” BARB
3/8” BARB
1/2” BARB
1/4” BARB
3/8” BARB
1/2” BARB
Pipe x Barb
SMC FN-226-4B4M-E
SMC FN-226-4M6B-E
SMC FN-226-8B4M-B
1/4” M.N.P.T.
1/4” M.N.P.T.
1/4” M.N.P.T.
1/4” BARB
3/8” BARB
1/2” BARB
MAX
PRESSURE
125
125
125
125
125
125
BRASS BALL VALVES
1/8” – 3/4”
PART #
SMC 012-2F2M-BT
SMC 025-4F4F-BT
SMC 036-6F6F-BT
SMC 025-4F4M-BT
SMC 025-4F4B-BT
SMC 025-4FMN-BT
SMC 025-MN4M-BT
END CONN.
1/8” F.N.P.T.
1/4” F.N.P.T.
3/8” F.N.P.T.
1/4” F.N.P.T.
1/4” F.N.P.T.
1/4” F.N.P.T.
1/4” M.N.P.T.
END CONN.
1/8” F.N.P.T.
1/4” F.N.P.T.
3/8” F.N.P.T.
1/4” M.N.P.T.
1/4” HOSE BARB
11/16”-16 MALE THRD.
11/16”-16 MALE THRD.
SMC 075-FG-BT
SMC 075-HG-BT
3/4” F.N.P.T.
3/4” F.G.H.T.
3/4” M.G.H.T.
3/4” M.G.H.T.
2200 SERIES SMALL SOLENOID VALVE
12-Volt DC solenoid valve has a ¼” NPT female inlet & outlet.
These direct operating valves can be used for foam & dye
markers, small sprayers, boom end nozzles, chemical injection
systems, individual nozzle shutoffs, etc. The valve housing is
made of glass filled nylon & wetted metal parts of 304 and 430
stainless steel. Viton seal and “O” rings are standard. Coils are
totally epoxy encapsulated with ¼ male spade.
RMC PLGR.2240 • 1 GPM, 80 PSI
High pressure, 600 PSI 1/4 turn
bronze valves, stainless ball Teflon®
seats
APO 70-603-01 - 1/2” FNPT
APO 70-604-01 - 3/4” FNPT
APO 70-605-01 - 1” FNPT
APO 70-606-01 - 1 1/4” FNPT
APO 70-607-01 - 1 1/2” FNPT
APO 70-608-01 - 2” FNPT
2 way Bronze Ball
Valves
High pressure, 600 PSI 1/4 turn
bronze valves, stainless steel &
stem Teflon® seats.
APO 71-144-01 - 3/4” FNPT
APO 71-145-01 - 1” FNPT
APO 71-146-01 - 1 1/4” FNPT
APO 71-147-01 - 1 1/2” FNPT
Economical Medium Pressure
400 PSI, 1/4 turn bronze valve, stainless steel ball, Teflon® seats.
APO 32-101-01 - 1/4” FNPT
APO 32-105-01 - 1” FNPT
APO 32-102-01 - 3/8” FNPT
APO 32-106-01 - 1 1/4” FNPT
APO 32-103-01 - 1/2” FNPT
APO 32-107-01 - 1 1/2” FNPT
APO 32-104-01 - 3/4” FNPT
APO 32-108-01 - 2” FNPT
AA144P DIRECTOVALVE®
2-WAY ELECTRICALLY CONTROLLED SOLENOID VALVE
• 10 GPM (37.9 l/m) flow w/ only 5 PSI (0.35 bar) pressure drop
• 2.5 amp current draw
• Polypropylene body for chemical resistance
• Fabric reinforced Viton® diaphragms
• No stroke adjustment required
• Corrosion resistant. 430SS solenoid grade armature & stop
• Encapsulated coil and magnetic circuit
Model #
Inlet Size
Outlet Size
SSC AA144P-1
3/4”
1/2”
344BEC ELECTRIC 12V VALVE
• 25 RPM, .6 second shut-off fully open to close
• Available in 2-way or 3-way versions
• Stainless stem with optional polypropylene or
stainless steel ball
• Maximum pressure 300 PSI
• Flow rate 24-32 GPM depends on style of valve
• Wetted parts are nylon, Teflon®, polypropylene,
stainless steel & Vitron®
• Available in 3/4” or 1” connections
SSC 344BEC-23-C 3/4”
SSC 344BEC-24-C 1”
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
93
SPRAY GUNS
OTHER guNjET SPRAY guNS
SPRAY guNS
BRASS MODEL AA43 SERIES guNS
A single hand operated spray gun
• 1/2” NPT Inlet, trigger control on/off
• Trigger pattern adjustment hollow cone to straight stream
• Available low (200PSI) or high (700PSI) pressure
All below have a twist handle for on/off and adjustment of
pattern. Two hand operation, replaceable disc for volume
control.
SSC AA2-45 - 24” long - Brass 3/4” FHT Inlet - • 3.5 lbs.
SSC AA43H-8 - 22” long, high pressure
SSC AA43L-8 - 22” long, low pressure
SSC AA12-6 - 20” long - Brass 3/4” FHT Inlet - • 1.75 lbs.
SSC AA43HA-8 - 13” long, high pressure
SSC AA43LA-8 - 13” long, low pressure
SSC AA18-AL-6 - 20” long - Aluminum 1/4” FPT Inlet - • 1 lb.
OPTIONAL guNjET® ACCESSORIES
guNjET® LAWN SPRAY guN
Model No.
SSC 25660-1.5
Nozzle Tip #
Tip Color
CP 25670-1.5 NY
SSC 25660-3.0
CP 25670-3.0 NY
Gray
Black
SSC 25660-4.0
CP 25670-4.0 NY
Red
SSC 11740B
Swivel connector with FHT. Free
swiveling, leak proof
SSC 7029
Adapter for GHT (1/2 MPT to
FGT) Brass (43 Guns)
SSC 7029
VALVES
BRASS EXTENSIONS
HANDLES
4688 TRIggER VALVE
With trigger lock. Max flow
rate 2 GPM, max pressure
250 PSI (10 bar). 1/4”
NPT (F) inlet connection,
11/16”-16 (M) outlet
connection. Brass material.
SSC 4688
4727 SuRE gRIP HANDLE
Brass, rubber coated, 1/4” NPS (M) or BSPT
hose inlet connection. SSC 4727
6466 TRIggER VALVE
4754 SuRE gRIP HANDLE
Same as 4688, no trigger
lock, extra long trigger.
SSC 6466
SSC 11740B
Brass, rubber coated, 3/4” garden hose
thread (F) inlet connection. SSC 4754
Tip
STRAIgHT & CuRVED extensions 4673 and
6671 for pressure to 125 PSI (9 bar). 7715
for pressure to 250 PSI (17 bar). Fits models
23L, 31 GunJet spray guns & trigger valves.
Straight
w/ Fixed
Body
Curved
w/Swivel
Body
Curved
w/Fixed
Body
7715-8
4673-8
6671-8
8”
3
7715-18
4673-18
6671-18
18”
4
7715-24
4673-24
6671-24
24”
5
7715-30
4673-30
6671-30
30”
5 1/2
7715-36
4673-36
6671-36
36”
6 1/4
7715-48
4673-48
6671-48
48”
7 1/2
Brass Extension
Example of assem
bled brass spray wa
nd
Valve
Ext.
Length
Net
Weight
in oz.
Handle
Cap CP1325
OuR OWN FEEDINg NEEDLE
Manufactured by OESCO, Inc., this high pressure, high volume
needle is made of thick wall steel pipe tapered and threaded
together. Complete with adjustable step plate (doubles as splash
plate). A high pressure 3/4” squeeze handle valve is mounted in the 3/4” pipe handle. A 3/4” FHT brass
adapter is included ready to attach to hose. The tip is an interchange-able: 2, 3, 4 or 6 hole. Please
specify which tip when ordering. Length 40”. All parts available.
GPM at 200 PSI
SET FN-12
SET FN-13
SET FN-14
SET FN-16
(2 hole tip) • 10 lbs.
(3 hole tip) • 10 lbs.
(4 hole tip) • 10 lbs.
(6 hole tip) • 10 lbs.
13
20
27
40
Replacement tips:
ORC FNT-2
ORC FNT-3
ORC FNT-4
ORC FNT-6
2 hole • .25 lb.
3 hole • .25 lb.
4 hole • .25 lb.
6 hole • .25 lb.
Replacement valve: KIN 305A5-1 - 3/4” squeeze valve
Valve repair kit: KIN 305AFF-5-KIT
94
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
Largest John Bean
parts inventory in
the Northeast!
jOHN BEAN 785 SPRAY guN
Excellent all purpose spray gun. Aluminum
construction, adjustable pattern, trigger
control (with latch), interchangeable discs for
volume control. Assortment of discs supplied
with gun. Optional large volume kit available.
24” long, 3/4” FGH inlet, 48 GPM, 800 PSI
capacity.
jBS 5253228 • 5 lbs.
jBS 5254037 High volume kit (over 25
gpm)
jOHN BEAN 757 SPRAY guN
Nice aluminum constructed true pistol
spray gun for 1
hand operation.
Pattern adjustment,
locking trigger,
interchangeable
discs for volume
control. Assortment of discs supplied with
gun. 11” long, 3/4” FGH inlet, 13 GPM, 600
PSI capacity.
jBS 1235000 • 1.5 lbs.
®
SPRAY GUNS
gREEN gARDE® SPRAY guN
D
B
This rugged stainless steel and brass
pistol gun is barrel adjustable from
fine cone spray to straight stream.
Interchangeable tips & nozzles give
various patterns & volumes. The
body is tapped 1/4 FPT with a plug for
installation of a gauge for calibration
purposes. Large trigger has locking clip.
Length 7”, 3/4” FHT inlet.
F
E
C
A
K
j
I
H
g
jD9-CT STANDARD SPRAY guN
GRE 38507
Supplied with Large tip (3.86 oz.) and manual adjustable pattern
control, trigger is on/off
gRE 38501 • 2 lbs.
jD9-PT SPRAY guN
Trigger on PT model controls on/off and variable spray pattern.
gRE 38507 • 2 lbs.
jD9-CT guN ACCESSORIES
A
B
C
D
E
F
gRE 38633
gRE 38634
gRE 38635
gRE 38636
gRE 38637
gRE 38638
Flooding Plastic • 4 GPM
Flooding Plastic • 2 GPM
Flooding Plastic • 5 GPM
Flooding Baseball Head • 2 GPM
Flooding Plastic • 1 GPM
Flooding Plastic • 1/2 GPM
SPRAY guN TIPS:
No.
g gRE 38606
H gRE 38605
I gRE 38604
j gRE 38602
K gRE 38603
Size
Extra Small
Small
Medium
Large
Extra Large
Flow Rate g g
0.3 to 1 GPM
1.0 to 3 GPM
2.0 to 5 GPM
3.0 to 8 GPM w/gun
10 to19 GPM
gRE 38919 - Heavy-duty feeder with
38917, 2-hole tip complete - Gun sold
separately.
gRE 38918 - 3-hole tip only
gRE 38901 - 4-hole tip only
gRE 38906 - 7” stainless steel
needle extension w/O-rings
gRE 38907 - 11” stainless steel needle
extension w/O-rings
gRE 38908 - 36” extension
gRE 38903 - 18” extension
gRE 38905 - Floppy foot plate
gRE 38904 - Extension connector
w/O-rings
TIP ADAPTERS, WANDS
HYPRO LONg DISTANCE guN
21” barrel, 30gpm flow, up to 1200psi,
pattern adjusts by moving front handle.
HYP 3381-0011 • 6 lbs.
gRE 38512
gRE 38990
gRE 38545
gRE 38546
Tip adapter for use with Spraying Systems Co. wands
Tip adapter for use with Hudson spray wands or with Calibrator™ valve
Hudson straight 18” brass spray wand w/ Delavan Raindrop Low Drift RF8 nozzle
Hudson curved 18” brass spray wand w/ Delavan Raindrop Low Drift RF8 nozzle
HAMILTON SENIOR BRASS SPRAY guN
Heavy duty brass spray gun. 900 PSI maximum pressure. All orifice discs are made from
hardened steel. Inlet: 3/4” FGHT. Comes with #5 disc. 22” OAL.
HAM 1000-01
HYPRO TuRBO guN
7” barrel, up to 10gpm flow, up to 700psi,
one hand operation, 1/2” MPT inlet trigger
valve, pattern adjustment & a sliding cone
over the tip to inject air for turbo mist.
HYP 3381-0013 • 1.65 lbs.
PuMP gPM
Recommended
Pump Capacity,
Pressure & Tips
for Shade Tree
Spraying
We have the largest John Bean parts inventory in the Northeast!
ALL parts available for John Bean Sprayers, Accessories & Guns.
PuMP PSI
HOSE
SIzE
3/4”
guN & DISC
NOzzLE
PSI
450 - 550
TREE
HEIgHT
65’ to 110’
450 - 550
50’ to 70’
60
50
600-800# with
100’ of 3/4” hose
35
600# with
100’ of hose
3/4”
35
25
600-700#
with 200’ of hose
3/4”
785 & #14
450 - 550
40’ to 65’
20
400-500#
with 100’ of hose
400#
with 100’ of hose
5/8”
785 & #14
250 - 350
35’ to 50’
1/2”
785 & #10
300 - 350
20’ to 35’
10
785 equipped with special kit
& #22 disc
785 equipped with special kit
& #16 disc
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
95
HOSE
Spray Hose
CALL OESCO, INC. FOR ALL OF YOUR HOSE NEEDS.
LOW PRESSuRE RuBBER SPRAY SuCTION HOSE
We supply vinyl & all weather suction hose.
HOSE
MCg 1/4X2-67BH - 1/4” ID - 300 PSI rated
MCg 3/8X2-67BH - 3/8” ID - 300 PSI rated
MCg 1/2X2-67BH - 1/2” ID - 300 PSI rated
MCg 5/8X2-67BH - 5/8” ID - 200 PSI rated
MCg 3/4X2-67BH - 3/4” ID - 200 PSI rated
MCg 1X2-67BH - 1” ID - 200 PS rated
MCg 1-1/4X2-67BH - 1 1/4” ID - 150 PSI rated
MCg 1-1/2X2-67BH - 1 1/2” ID - 250 PSI rated
Can also be used for low pressure transfer
hose. Other suction hose available - call for details.
MCg 016-300-EPDM - 1” ID - all weather rubber
MCg 020-300-EPDM - 1 1/4” ID - all weather rubber
MCg 024-300-EPDM - 1 1/2” ID - all weather rubber
MCg 032-300-EPDM - 2” ID - all weather rubber
MCg 040-300-EPDM - 2 1/2” ID - all weather rubber
MCg 048-300-EPDM - 3” ID - all weather rubber
CLEAR SuCTION HOSE
HIgH PRESSuRE RuBBER
SPRAY HOSE
750 PSI rated
MCg 006-NR-SPRAY - 3/8” ID Spray Hose
MCg 008-NR-SPRAY - 1/2” ID Spray Hose
MCg 012-NR-SPRAY - 3/4” ID Spray Hose
MCg 016-NR-SPRAY - 1” ID Spray Hose
REA HNP075 - 3/4” Armovin wire
reinforced PVC
REA HNP100 - 1” Armovin wire
reinforced PVC
REA HNP125 - 1 1/4” Armovin
wire reinforced PVC
REA HNP150 - 1 1/2” Armovin
wire reinforced PVC
REA HNP200 - 2” Armovin wire
reinforced PVC
CLEAR PVC HOSE
FDA COMPLIANT
NYLON BRAIDED HOSE
Nylon braided hose, 250 lbs. maximum
pressure sizes available, food and beverage
rated.
FLO 2H5015/0375 - 3/8” ID - 225 PSI
FLO 2H5015/050 - 1/2” ID - 200 PSI
FLO 2H5015/0625 - 5/8” ID - 200 PSI
FLO 2H5015/075 - 3/4” ID - 150 PSI
FLO 2H5015/100 - 1” ID - 125 PSI
FLO 2H5015/125- 1 1/4” ID - 100 PSI
MCg ABH02017- 1/4” ID 1/16” wall thickness
MCg ABH02027 - 3/8” ID 1/16” wall thickness
MCg ABH02036 - 1/2” ID 1/16” wall thickness
MCg ABH02046 - 5/8” ID 1/8” wall thickness
MCg ABH02053 - 3/4” ID 1/8” wall thickness
MCg ABH00062- 1” ID 1/8” wall thickness
MCg ABH00071 - 1-1/4” ID 1/4” wall thickness
REINFORCED CLEAR PVC HOSE
FDA COMPLIANT
FLO 2A8070/100-100 - 1” diameter
FLO 2A8070/125-100 - 1 1/4” diameter
FLO 2A8070/150-100 - 1 1/2” diameter
FLO 2A8070/200-100 - 2” diameter
HOSE CuTTER
Here’s a fast and clean tool to cut hose. No
deburring necessary and it’s light-weight with
strong nylon handles. Replacement blades
available.
gRE 38930 - Hose Cutter • 8 oz.
gRE 38931 - Replacement Blade • 1 oz.
96
CLEAR RIBBED HOSE
FDA COMPLIANT
Clear Ribbed food grade hose, 80 PSI.
FLO 2A8060/200 - 2” ID
LAY FLAT DISCHARgE HOSE
Blue lay flat discharge hose. Constructed of
PVC reinforced with synthetic fabric.
All sizes are 80 PSI rated.
MCg 016-PVC-FLAT 1” ID
MCg 024-PVC-FLAT 1 ½” ID
MCg 032-PVC-FLAT 2” ID
Spray hose is sized by ID
(inside diameter).
Hose can be cut
to any length.
Fittings & Coupling sets
installed to order
We stock
thousands of feet
of hose!
Call us for more
information.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
SPRAY HOSE
OUR BEST SPRAY HOSE!
So good we warrantee it for 3 years!
High-Pressure, Braid-Reinforced, Neon, PVC Hose
800 PSI working pressure, 3000 PSI burst, 3 Year Warranty.
Reinforced PVC with high burst strength. Melded inner core and cover to form complex reinforcement that
will not separate under high pressure. Light, bright color is easy to see, won’t mark curbs or sidewalks.
Sizes to fit any need. Costs you less because it lasts longer.
GRE
GRE
GRE
GRE
GRE
GRE
GRE
GRE
GRE
38684
38685
38686
38688
38689
38690
38553
38695
38696
3/8” x 300’
3/8” x 400’
3/8” x 600’ 1/2” x 300’ 1/2” x 400’
1/2” x 600’
5/8” x 300’
3/4” x 300’
3/4” x 400’
3/8” ID
3/8” ID 3/8” ID
1/2” ID
1/2” ID
1/2” ID
5/8” ID
3/4” ID
3/4” ID
Couplings installed on hose to order. Please specify installation requirements when ordering.
Unique PVC/polyurethane blended core provides excellent resistance to hydrocarbon-based tree spray,
lawn care and pest control chemicals. Reinforced with high tensile strength yarn. PVC ribbed cover and
thick walls allow this spray hose to withstand the toughest applications as well as resist kinking.
General ApplicationS:
•Lawn Care
•Agricultural Spray
•Commercial Weed Spray
•Tree and Orchard Spraying
600 PSI Yellow Braid PVC Hose
GRC A-1661-3/8x300
GRC A-1661-3/8x400
GRC A-1661-1/2x300
GRC A-1661-1/2x400
3/8” ID x 300’
3/8” ID x 400’
1/2” ID x 300’
1/2” ID x 400’
800 PSI Green PVC Spray Hose
GRC A-1687-5/8x300
GRC A-1687-3/4x300
5/8” ID x 300’
3/4” ID x 300’
Roll it up!
Hannay hose reel, p. 82
Get spray guns!
Pgs. 94 & 95
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
97
HOSE COUPLINGS / FITTINGS
PLATED STEEL COuPLINg SETS & HOSE FITTINgS FOR SPRAY HOSE
Coupling sets are important factors in prolonging the life of your high pressure hose.
We supply Green Garde hose fittings on all high pressure hose we sell. These hose
fittings are designed to assure maximum flow with large ID and long shanks. The
shank end is rounded to prevent early hose failure and to aid in the installation of
fittings on the hose.
All below threads are gHT
gREEN gARDE HIgH PRESSuRE HOSE FITTINgS
No.
Description
Shank Length
inches
GRE 38941
1/2” barb shank X MHT
1/2”
2 5/16”
GRE 38940
1/2” barb shank
(w/nut and washer) X FHT
1/2”
2 5/16”
GRE 38944
5/8” barb shank X MHT
5/8”
2 3/8”
GRE 38943
5/8” barb
(w/nut & washer) X FHT
5/8”
2 3/8”
GRE 38947
3/4” barb X MHT
3/4”
2 5/16”
GRE 38946
3/4” barb
(w/nut & washer) X FHT
3/4”
2 5/16”
DIXON HIgH PRESSuRE
DIXON
HIGH
PRESSuRE
3/8”
HOSE
FITTINgS
3/8”HOSE fITTINGS
BN Hose shank X Male Pipe Thread Sh.Wt.
DVC BN11
1/8” x 1/8” MPT
1 oz.
DVC BN151
3/16” x 1/8” MPT
1 oz.
DVC BN152
3/16” x 1/4” MPT
1 oz.
DVC BN21
1/4” x 1/8” MPT
1 oz.
DVC BN22
1/4” x 1/4” MPT
1 oz.
DVC BN23
1/4” x 3/8” MPT
2 oz.
DVC BN251
5/16” x 1/8” MPT
1 oz.
DVC BN252
5/16” x 1/4” MPT
1 oz.
DVC BN253
5/16” x 3/8” MPT
2 oz.
DVC BN31
3/8” x 1/8” MPT
1 oz.
DVC BN32
3/8” x 1/4” MPT
1 oz.
DVC BN33
3/8” x 3/8” MPT
1 oz.
DVC BN34
3/8” x 1/2” MPT
2 oz.
DVC BN42
1/2” x 1/4” MPT
1 oz.
DVC BN43
1/2” x 3/8” MPT
2 oz.
DVC BN44
1/2” x 1/2” MPT
2 oz.
DVC BN46
1/2” x 3/4” MPT
3 oz.
DVC BN53
5/8” x 3/8” MPT
2 oz.
DVC BN54
5/8” x 1/2” MPT
2 oz.
DVC BN56
5/8” x 3/4” MPT
3 oz.
DVC BN64
3/4” x 1/2” MPT
2 oz.
DVC BN66
3/4” x 3/4” MPT
3 oz.
DVC BN86
1” x 3/4”
MPT
3 oz.
DVC BN88
1” x 1”
MPT
3 oz.
“KINg” STEEL NIPPLES
washer
38940
38941
HOSE SHANK TYPE FITTINg
PLATED STEEL
Hose Shank X Male Pipe Thread
DVCSTC11/2”x1/2”MPT•1/4lb.
DVCSTC53/4”x3/4”MPT•1/4lb.
DVCSTC101’x1”MPT•1/4lb.
DVCSTC1511/4”x11/4”MPT•1/2lb.
DVCSTC2011/2”x11/2”MPT•1/2lb.
DVCSTC252”x2”MPT•1lb.
DVCSTC3021/2”x21/2”MPT•2lbs.
DVCSTC353”x3”MPT•3lbs.
38944
38947
nut
Fittings, Coupling Sets and Adapters
Note: All fittings are identified by listing the thread as
(m) male, (f) female, (pt) pipe thread.
(GHT) Hose thread means 3/4” garden hose thread,
(m) male, (f) female .
Hose barbs (HB) or hose shanks are the size
of the ID of the hose the barb is fitting into.
BRASS SHORT SHANK
FITTINgS
gHT Thread X Hose Shank
Female with Swivel:
DVCBCF73-FHTx3/8”•2oz.
DVCBCF74-FHTx1/2”•2oz.
DVCBCF75-FHTx5/8”•2oz.
DVCBCF76-FHTx3/4”•2oz.
Male:
DVCBCM73-MHTx3/8”•2oz.
DVCBCM74-MHTx1/2”•2oz.
DVCBCM75-MHTx5/8”•2oz.
DVCBCM76-MHTx3/4”•2oz.
STAINLESS STEEL
SHORT SHANK COuPLINgS
Hose shank X Male Pipe Thread
DVCRST11/2”x1/2”MPT•1/4lb.
DVCRST53/4”x3/4”MPT•1/4lb.
DVCRST101”x1”MPT•1/4lb.
DVCRST1511/4”x11/4”MPT•1/2lb.
DVCRST2011/2”x11/2”MPT•1/2lb.
DVCRST252”x2”MPT•1lb.
WASHERS FOR SuCTION, LONg
& SHORT SHANK COuPLINgS
DVCKHN222-1/4”x1/4”MPT•1oz.
DVCKHN322-3/8”x1/4”MPT•1oz.
DVCKHN332-3/8”x3/8”MPT•2oz.
DVCKHN342-3/8”x1/2”MPT•4oz.
DVCKHN422-1/2”x1/4”MPT•1oz.
DVCKHN432-1/2”x3/8”MPT•4oz.
DVCKHN442-1/2”x1/2”MPT•4oz.
DVCKHN462-1/2”x3/4”MPT•6oz.
DVCKHN642-3/4”x1/2”MPT•2oz.
DVCKHN662-3/4”x3/4”MPT•6oz.
DVCKHN862-1”x3/4”MPT•6oz.
DVCKHN882-1”x1”MPT•10oz.
38946
38943
Complete green garde coupling sets. Order by individual part.
DVC
SLS347
x 3/4”
DVC
SLS347
3/8”3/8”
hosehose
barbbarb
x 3/4”
FHTFHT
DVC SLS317 3/8” hose barb x 3/4” MHT
DVC SLS317 3/8” hose barb x 3/4” MHT
BRASS HOSE BARBS
98
Fits Hose ID inches
Rubber Washer:
DVC KRW5 - 3/4”
DVC KRW10 - 1”
DVC KRW15 - 1 1/4”
DVC KRW20 - 1 1/2”
DVC KRW25 - 2”
DVC KRW30 - 2 1/2”
DVC KRW35 - 3”
Leather Washer:
DVC KLW5 - 3/4”
DVC KLW10 - 1”
ELBOW WINgNuT FITTINgS
REA EL050F037HB
90° 3/8” Barb X 1/2” FPT Wingnut
REA EL050F050HB
90° 1/2” Barb X 1/2” FPT Wingnut
STRAIgHT WINgNuT
FITTINgS
HYP 9910-110130
1/2” Barb X 1/2” FPT Wingnut
HYP 9910-110131
3/8” Barb X 1/2” FPT Wingnut
gASKET
For Wingnut Fittings: REA BRAgS050
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
HOSE BANDS / GAUGES
SILICONE-fILLED
PRESSuRE GAuGE
BAND-IT jR.
C002 TOOL
For application of Band-It Jr. Smooth I.D.
Preformed Clamps.
BDT C00269 • 5.7 lbs.
BAND-IT C001 TOOL
This standard tool can be bench or vise
mounted & is used with the band bulk rolls
or with the J001 adapter for the preformed
clamps. This tool attaches the preformed
clamps to the hose & coupling to make
the most secure fitting possible to avoid all
leaks and failures in the hose.
BDT C00169 • 5 lbs.
BAND-IT jR. ADAPTER j001
The adapter is necessary when using
the preformed clamps on the C001 tool.
It allows the clamp to be correctly formed
and tail broken flush to the ring.
BDT J00169 • 2 lbs.
CENTER PuNCH TOOL
T-handle screw tensioning tool for up to 5/8”
wide preformed bands.
BDT T30069 • 3.2 lbs.
BAND-IT SMOOTH I.D. CLAMPS
Band-it preformed stainless steel clamps.
BDT JS2409 - 3/4” ID x 1/4” thick • 1 oz.
BDT JS2429 - 1” ID x 1/4” thick • 1 oz.
BDT JS2439 - 1” ID x 3/8” wide • 2 oz.
BDT JS2029 - 1 3/8” ID x 3/8” wide • 2 oz.
BDT JS2049 - 1 1/4” ID x 1/2” thick • 2 oz.
BDT JS2099 - 2 1/2” ID x 5/8” thick • 2 oz.
BDT JS2059 - 1 1/2” ID x 5/8” thick • 2 oz.
BDT JS2149 - 4 1/2” ID x 3/4” wide • 2 oz.
BDT JS2199 - 8” ID x 3/4” wide • 2 oz.
BDT JS4129 - 3 1/2” ID x 3/4” thick • 1/2 lb.
WORM GEAR
STYLE HSS CLAMPS
All stainless construction combination 5/16”
hexagon and screw-driver slotted screw.
No.
Grip Range
From
To
DVC HSS8
1/2”
29/32”
DVC HSS10 9/16”
1 1/16”
DVC HSS12 11/16” 1 1/4” DVC HSS16 13/16” 1 1/2” DVC HSS20 13/16” 1 3/4” DVC HSS24 1 1/16” 2” DVC HSS28 1 5/16” 2 1/4” DVC HSS32 1 9/16” 2 1/2” DVC HSS36 1 13/16” 2 3/4” DVC HSS40 2 1/16” 3” DVC HSS44 2 5/16” 3 1/4” DVC HSS48 2 9/16” 3 1/2” Sh. Wt.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
1 oz.
WORM GEAR
STYLE MAH CLAMPS
Miniature all stainless construction with
combination 1/4” hexagon and screwdriver
slotted screw. 5/16” band width.
No.Grip Range
From To DVC
DVC
DVC
DVC
MAH4
MAH6
MAH8
MAH10
7/32” 7/16” 1/2” 9/16” 5/8”
25/32” 29/32”
1 1/16”
Sh. Wt.
“T” BOLT CLAMPS
Style STBC
No.
POk-IT-TOOL
Lightweight pocket size tool for use with
1/4-3/8” width band. It applies tension & has
a built-in cutter.
BDT J02069 • 1.5 lbs.
Grip Range
PSI
BAR
0-60
0-100
0-200
0-300
0-600
0-1000
0-1500
0-2000
0-3000
0-5000
0-10000
0-400
4
7
14
21
42
70
105
140
210
350
700
Hypro Model
WT.
HYP 2640-0009 .5 lbs.
HYP 2640-0010 .5 lbs.
HYP 2640-0011 .5 lbs.
HYP 2640-0007 .5 lbs.
HYP 2640-0008 .5 lbs.
HYP 2640-0001 .5 lbs.
HYP 2640-0002 .5 lbs.
HYP 2640-0003 .5 lbs.
HYP 2640-0004 .5 lbs.
HYP 2640-0005 .5 lbs.
HYP 2640-0014 .5 lbs.
REA LFG400
.5 lbs.
GG SERIES
GLYCERIN-fILLED
GAuGE
For use with air, gas,
oil & water. Brass
movement, phosphor
bronze Bourdon
tube, black enameled
aluminum pointer, white
background dial, acrylic window. 2 1/2” face.
Stem size 1/4” NPT connection & U-clamp.
PSI
Hypro Model
WT.
0-60
0-100
0-160
0-200
0-300
0-400
0-600
0-1000
0-1500
0-2000
0-3000
0-5000
0-6000
HYP WGG60C
HYP WGG100C
HYP WGG160C
HYP WGG200C
HYP WGG300C
HYP WGG400C
HYP WGG600C
HYP WGG1000C
HYP WGG1500C
HYP WGG2000C
HYP WGG3000C
HYP WGG5000C
HYP WGG6000C
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
.5 lbs.
1 oz.
1 oz.
1 oz.
1 oz.
CENTER PuNCH TOOL
These ratchet action tensioning tools are
for applying center punch and center punch
open end clamps with a center punch lock.
BDT S03869 • 1 lb.
• Silicone-filled gauge
• Stainless Steel Case
• 2 1/2” Face
• 1/4” NPT (M) Fitting
• Bronze Bourdon Tube
• Dual Scale Dial
• Brass Stem
• Clear Acrylic Lens
DVC STBC188 from 1.724” to 1.942”
DVC STBC200 from 1.844” to 2.062”
DVC STBC225 from 2.094” to 2.312”
DVC STBC250 from 2.344” to 2.562”
DVC STBC275 from 2.516” to 2.812”
DVC STBC300 from 2.766” to 3.062”
DVC STBC325 from 3.016” to 3.312”
DVC STBC350 from 3.266” to 3.562”
DVC STBC375 from 3.516” to 3.812”
DIXON STANDARD
DRY GAuGES
1.5% accuracy, black steel case,
acrylic crystal, black aluminum pointer, 1/4”
lower mount.
DVC GL115 - 0-30 PSI, 1 1/2” Face • .5 lb.
DVC GL120 - 0-60 PSI, 1 1/2” Face • .5 lb.
DVC GL320 - 0-30 PSI, 2 1/2” Face • .5 lb.
DVC GL325 - 0-60 PSI, 2 1/2” Face • .5 lb.
DVC GL330 - 0-100 PSI, 2 1/2” Face• .5 lb.
DVC GL335 - 0-160 PSI, 2 1/2” Face• .5 lb.
DVC GL340 - 0-200 PSI, 2 1/2” Face• .5 lb.
DVC GL345 - 0-300 PSI, 2 1/2” Face• .5 lb.
DVC GL350 - 0-600 PSI, 2 1/2” Face• .5 lb.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
99
BANJO VALVES / FITTINGS
Part #
Description
POLYPROPYLENE PIPE FITTINgS
POLYPROPYLENE
BALL VALVES
4 bolt construction (6 bolt for large valves) with viton O rings and
teflon seats. 100 PSI max pressure.
4 BOLT VALVES
Description
Full Port
Full Port
Standard Port
Full Port
Standard Port
Full Port
Full Port
Standard Port
Part #
BjO V050
BjO V075
BjO V100
BjO V100FP
BjO V125
BjO V125FP
BjO V150
BjO V200
6 BOLT VALVES
Description
Part #
BjO V200FP
BjO V300
BjO V300FP
Full Port
Standard Port
Full Port
Pipe
NPT
Thru
Ball
1/2”
3/4”
1”
1”
1 1/4”
1 1/4”
1 1/2”
2”
3/4”
3/4”
3/4”
1”
1”
1 1/2”
1 1/2”
1 1/2”
Max
PSI
Pipe
NPT
Thru
Ball
150
100
100
2”
3”
3”
2 1/16”
2 1/2”
3”
Max
PSI
150
150
150
150
150
150
150
150
SINgLE uNION POLYPROPYLENE
BALL VALVES
• Precision molded of glass-reinforced
polypropylene for strength &
chemical resistance
• Maximum operating pressure 100 psi at 70° F.
Part #
Description
BjO uV075FP
3/4” Single Union Poly Valve
BjO uV100FP
1” Single Union Poly Valve
BjO uV125FP
1 1/4” Single Union Poly Valve
BjO uV150FP
1 1/2” Single Union Poly Valve
POLY NIPPLES
BjO NIP050-SH
BjO NIP075-SH
BjO NIP075-4
BjO NIP075-6
BjO NIP100-SH
BjO NIP100-4
BjO NIP100-6
BjO NIP125-SH
BjO NIP125-4
BjO NIP125-6
BjO NIP150-SH
BjO NIP200-SH
BjO NIP200-6
1/2” x Short Poly Nipple
3/4” x Short Poly Nipple
3/4” x 4” Poly Nipple
3/4” x 6” Poly Nipple
1” x Short Poly Nipple
1” x 4” Poly Nipple
1” x 6” Poly Nipple
1 1/4” x Short Poly Nipple
1 1/4” x 4” Poly Nipple
1 1/4” x 6” Poly Nipple
1 1/2” x Short Poly Nipple
2” x Short Poly Nipple
2” x 6” Poly Nipple
REDuCINg BuSHINg
BjO RB125-075
1 1/4” MPT x 3/4” FPT Red. Bush.
BjO RB125-100
1 1/4” MPT x 1” FPT Red. Bush.
BjO RB150-075
1 1/2” MPT x 3/4” FPT Red. Bush.
BjO RB200-075
2” MPT x 3/4” FPT Red. Bush.
BjO RB200-100
2” MPT x 1” FPT Red. Bush.
BjO RB200-150
2” MPT x 1 1/2” FPT Red. Bush.
POLY PIPE TEE
BjO TEE050
BjO TEE075
BjO TEE100
BjO TEE125
BjO TEE150
BjO TEE200
1/2” Poly Pipe Tee
3/4” Poly Pipe Tee
1” Poly Pipe Tee
1 1/4” Poly Pipe Tee
1 1/2” Poly Pipe Tee
2” Poly Pipe Tee
POLY ELBOWS 90°
BjO EL075-90
BjO EL100-90
BjO EL125-90
BjO EL150-90
BjO EL200-90
3/4” Poly Pipe Elbow 90°
1” Poly Pipe Elbow 90°
1 1/4” Poly Pipe Elbow 90°
1 1/2” Poly Pipe Elbow 90°
2” Poly Pipe Elbow 90°
POLY STREET ELBOWS 90°
BjO SL075-90
3/4” Pipe Street Elbow 90°
BjO SL100-90
1” Pipe Street Elbow 90°
BjO SL125-90
1 1/4” Pipe Street Elbow 90°
BjO SL150-90
1 1/2” Pipe Street Elbow 90°
BjO SL200-90
2” Pipe Street Elbow 90°
POLY STREET ELBOWS 45°
BjO SL125-45
1 1/4” Poly Pipe Street Elbow 45°
BjO SL150-45
1 1/2” Poly Pipe Street Elbow 45°
BjO SL200-45
2” Poly Pipe Street Elbow 45°
POLYPROPYLENE HOSE BARBS
STuBBY VALVES
2” Standard Port, Ball Valves
with 1.5” Ball Opening
• Stainless steel bolts
• Glass filled polypropylene
• Multiple design options
• Unique patented compact design
• Lightweight
• Maximum operating pressure 100 psi @ 70° F. 75 psi @ 150° F.
• All PTFE Seals
Part #
Description
BjO VSF200
2” Male Adaptor X 2” Female NPT
BjO VSFMT200
2” Male Adaptor X 2” Male NPT
BjO VSFHB200
2” Male Adaptor X 2” Male Hose Barb
Many other Banjo valves available - Call for details
®
BuLKHEAD FITTINgS
(For all tanks: poly, wood, steel)
Part#
Size
HYP WBH12
1/2” NPT
HYP WBH34
3/4” NPT
HYP WBH100
1” NPT
HYP WBH114
1 1/4” NPT
100
HYP WBH112
HYP WBH200
HYP WBH300
HYP WBH400
1 1/2” NPT
2” NPT
3” NPT
4” NPT
POLY STRAIgHT HOSE BARBS
BjO HB050-075
1/2” Male Thread x 3/4” HB
BjO HB075
3/4” Male Thread x 3/4” HB
BjO HB100
1” Male Thread x 1” HB
BjO HB100-075
1” Male Thread x 3/4” HB
BjO HB100-125
1” Male Thread x 1 1/4” HB
BjO HB125
1 1/4” Male Thread x 1 1/4” HB
BjO HB150
1 1/2” Male Thread x 1 1/2” HB
BjO HB150-125
1 1/2” Male Thread x 1 1/4” HB
BjO HB150-200
1 1/2” Male Thread x 2” HB
BjO HB200
2” Male Thread x 2” HB
BjO HB200-150
2” Male Thread x 1 1/2” HB
POLY 90° HOSE BARBS
BjO HB050/075-90 1/2” Male Thread x 3/4” HB 90°
BjO HB075-90
3/4” Male Thread x 3/4” HB 90°
BjO HB100-90
1” Male Thread x 1” HB 90°
BjO HB100/125-90 1” Male Thread x 1 1/4” HB 90°
BjO HB125-90
1 1/4” Male Thread x 1/4” HB 90°
BjO HB125/100-90 1 1/4” Male Thread x 1” HB 90°
BjO HB125/150-90 1 1/4” Male Thread x 1 1/2” HB 90°
BjO HB150-90
1 1/2” Male Thread x 1 1/2” HB 90°
BjO HB200/150-90 2” Male Thread x 1 1/2” HB 90°
BjO HB200-90
2” Male Thread x 2” HB 90°
POLY BOLTED “BOTTOM DRAIN”
TANK FLANgES
BjO BF100BD
BjO BF125BD
BjO BF150BD
1” x 1” Threaded Flange EPDM
1 1/4” x 1” Threaded Flange EPDM
1 1/2” x 2” Threaded Flange
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
SS / NYLON FITTINGS
®
Stainless Steel Fittings
All 304 Stainless Steel
NYLON TEES
Nylon Hose Fittings
MALE PIPE THREAD BY
HOSE BARB - MPT X HB
HYP 9A14 - 1/4” x 1/4”
HYP 9A12 - 1/2” x 1/2”
HYP 9A34 - 3/4” x 3/4”
HYP 9A100 - 1” x 1”
STREET ELBOW:
fEMALE PIPE THREAD BY
MALE PIPE THREAD MPT X fPT
HYP 7SE14 - 1/4” x 1/4”
HYP 7SE12 - 1/2” x 1/2”
HYP 7SE34 - 3/4” x 3/4”
HYP 7SE100 - 1” x 1”
COuPLING: fEMALE PIPE THREAD fPT X fPT
HYP 7FC14 - 1/4” x 1/4”
HYP 7FC12 - 1/2” x 1/2”
HYP 7FC34 - 3/4” x 3/4”
HYP 7FC100 - 1” x 1”
TEE: fEMALE PIPE
THREAD
HYP 7TT14 - 1/4” x 1/4” x 1/4”
HYP 7TT12 - 1/2” x 1/2” x 1/2”
HYP 7TT34 - 3/4” x 3/4” x 3/4”
HYP 7TT100 - 1” x 1” x 1”
ELBOW: fEMALE PIPE THREAD
90° - fPT X fPT
HYP 7LL14 - 1/4” x 1/4”
HYP 7LL12 - 1/2” x 1/2”
HYP 7LL34 - 3/4” x 3/4”
HYP 7LL100 - 1” x 1”
REDuCER BuSHING - MPT X fPT
HYP 7RB3814 - 3/8” x 1/4”
HYP 7RB1214 - 1/2” x 1/4”
HYP 7RB1238 - 1/2” x 3/8”
HYP 7RB3412 - 3/4” x 1/2”
HYP 7RB10034 - 1” x 3/4”
NIPPLE - MPT X LENGTH
HYP 714112 - 1/4” x 1 1/2”
HYP 714300 - 1/4” x 3”
HYP 712118 - 1/2” x 1 1/8”
HYP 712112 - 1/2” x 1 1/2”
HYP 712200 - 1/2” x 2”
HYP 734138 - 3/4” x 1 3/8”
HYP 734400 - 3/4” x 4”
HYP 7100112 - 1” x 1 1/2”
HYP 7100400 - 1” x 4”
NYLON TEES
1/4” Hose Size
DVC TN21 - 1/8”MPT • 1 oz.
DVC TN22 - 1/4”MPT • 1 oz.
DVC TN23 - 3/8”MPT • 1 oz.
DVC TN24 - 1/2” MPT • 1 oz.
DVC TN26 - 3/4” MPT • 1 oz. DVC TN28 - 1” MPT • 1 oz.
5/16” Hose Size
DVC TN252 - 1/4” MPT • 1 oz.
3/8” Hose Size
DVC TN31 - 1/8” MPT • 1 oz.
DVC TN32 - 1/4” MPT • 1 oz.
DVC TN33 - 3/8” MPT • 1 oz.
DVC TN34 - 1/2” MPT • 1 oz.
DVC TN36 - 3/4” MPT • 1 oz.
1/2” Hose Size
DVC TN41 - 1/8” MPT • 1 oz.
DVC TN42 - 1/4” MPT • 1 oz.
DVC TN43 - 3/8” MPT • 1 oz.
DVC TN44 - 1/2” MPT • 1 oz.
DVC TN46 - 3/4” MPT • 1 oz.
5/8” Hose Size
DVC TN53 - 3/8” MPT • 2 oz.
DVC TN54 - 1/2” MPT • 2 oz.
DVC TN56 - 3/4” MPT • 2 oz.
3/4” Hose Size
DVC TN63 - 3/8” MPT • 2 oz.
DVC TN64 - 1/2” MPT • 2 oz.
DVC TN66 - 3/4” MPT • 2 oz.
DVC TN68 - 1” MPT • 2 oz.
DVC TSSS222 - 1/4” x 1/4” x 1/4”
DVC TSSS333 - 3/8” x 3/8” x 3/8”
DVC TSSS444 - 1/2” x 1/2” x 1/2”
DVC TSSS666 - 3/4” x 3/4” x 3/4”
Tuff LITE 90° NYLON ELL
DVC TLSS22 – 1/4” Hose size
DVC TLSS33 – 3/8” Hose size
DVC TLSS44 – 1/2” Hose size
DVC TLSS66 – 3/4” Hose size
Tuff LITE 90° NYLON
THREADED ELL
DVC TLS21 – 1/8” MPT, 1/4” Hose
DVC TLS22 – 1/4” MPT, 1/4” Hose
DVC TLS23 – 3/8” MPT, 1/4” Hose
DVC TLS31 – 1/8” MPT, 3/8” Hose
DVC TLS32 – 1/4” MPT, 3/8” Hose
DVC TLS33 – 3/8” MPT, 3/8” Hose
DVC TLS34 – 1/2” MPT, 3/8” Hose
DVC TLS36 – 3/4” MPT, 3/8” Hose
DVC TLS42 – 1/4” MPT, 1/2” Hose
DVC TLS43 – 3/8” MPT, 1/2” Hose
DVC TLS44 – 1/2” MPT, 1/2” Hose
DVC TLS46 – 3/4” MPT, 1/2” Hose
DVC TLS48 – 1”MPT, 1/2” Hose
DVC TLS53 – 3/8” MPT, 5/8” Hose
DVC TLS54 – 1/2” MPT, 5/8” Hose
DVC TLS56 – 3/4” MPT, 5/8” Hose
DVC TLS58 – 1” MPT, 5/8” Hose
1” Hose Size
DVC TLS63 – 3/8” MPT, 3/4” Hose
DVC TLS64 – 1/2” MPT, 3/4” Hose
DVC TLS66 – 3/4” MPT, 3/4” Hose
DVC TLS68 – 1” MPT, 3/4” Hose
1 1/4” Hose Size
DVC TLS86 – 3/4” Male NPT, 1” Hose
DVC TLS88 – 1” Male NPT, 1” Hose
DVC TN86 - 3/4” MPT • 3 oz.
DVC TN88 - 1” MPT • 3 oz.
DVC TN158 - 1” MPT • 3 oz.
DVC TN150 - 1 1/4” MPT • 3 oz.
DVC TN1520 - 1 1/2” MPT • 3 oz.
1 1/2” Hose Size
DVC TN2015 - 1 1/4” MPT • 3 oz.
DVC TN200 - 1 1/2” MPT • 3 oz.
2” Hose Size
DVC TN250 - 2” MPT • 4 oz.
We stock thousands of fittings.
Call us with your needs.
Tuff-LITE NYLON INSERTS & SHORT SHANk COuPLINGS
Female
Male
1/2” Hose Size
DVC TCF74 - 3/4” GHT • 1 oz.
1/2” Hose Size
DVC TCM74 - 3/4” GHT • 1 oz.
3/4” Hose Size
DVC TCF76 - 3/4” GHT • 1 oz.
3/4” Hose Size
DVC TCM76 - 3/4” GHT • 1 oz.
3/8” Hose Size
DVC TCF73 - 3/4” GHT • 1 oz.
DVC TSST222 - 1/4” x 1/4” x 1/4” MPT
DVC TSST333 - 3/8” x 3/8” x 3/8” MPT
DVC TSST444 - 1/2” x 1/2” x 1/2” MPT
DVC TSST666 - 3/4” x 3/4” x 3/4” MPT
3/8” Hose Size
DVC TCM73 - 3/4” GHT • 1 oz.
hose menders
Tuff-LITE MENDER - (HIGH TENSILE NYLON)
DVC TM2 - 1/4” • 1 oz.
DVC TM25 - 5/16” • 1 oz. DVC TM3 - 3/8” • 1 oz.
DVC TM4 - 1/2” • 1 oz.
DVC TM5 - 5/8” • 2 oz.
DVC TM6 - 3/4” • 2 oz.
DVC TM8 - 1” • 2 oz. DIXON BRASS HOSE MENDER
DVC BM15 - 3/16” • 1 oz.
DVC BM2 - 1/4” • 1 oz. DVC BM25 - 5/16” • 1 oz.
DVC BM3 - 3/8” • 1 oz.
DVC BM4 - 1/2” • 1 oz.
DVC BM5 - 5/8” • 1 oz.
DVC BM6 - 3/4” • 1 oz.
“BOSS” HOSE MENDER
Collars to engage grip fingers of “Boss” clamps.
Plated materials malleable iron or plated tubular steel
depending on size.
DVC KM42 - 1/2” • .25 lb.
DVC KM52 - 5/8” • .25 lb. DVC KM62 - 3/4” • .50 lb.
DVC KM82 - 1” • .75 lb. Other sizes available by special order
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
101
BRASS FITTINGS / ADAPTERS
FORgED 90° ELBOW:
CLOSE NIPPLE:
PART #
FAI 112-A
FAI 112-B
FAI 112-C
FAI 112-D
FAI 112-E
FAI 112-H
PART #
FAI 99-B
PIPE
1/8
1/4
3/8
1/2
3/4
1
HEX NIPPLE:
PART #
FAI 122-A
FAI 122-B
FAI 122-C
FAI 122-D
FORgED 90°
STREET ELBOW:
PART #
FAI 116-A
FAI 116-B
FAI 116-C
PIPE
1/8
1/4
3/8
1/2
PIPE PIPE
1/4 to 1/8
3/8 to 1/8
3/8 to 1/4
1/2 to 1/4
1/2 to 3/8
LONg NIPPLE:
PART #
1/4 NPT
FAI 113-B1-1/2
FAI 113-B2
FAI 113-B3
LENgTH
1/4
1/4
1/4
1 1/2”
2”
3”
3/8 NPT
FAI 113-C1-1/2 3/8
FAI 113-C2
3/8
FAI 113-C3
3/8
1 1/2”
2”
3”
1 1/2”
2”
3”
REDuCINg COuPLINg:
PART #
FAI 119-BA
FAI 119-CA
FAI 119-CB
FAI 119-DA
FAI 119-DB
FAI 119-DC
PIPE PIPE
1/4 to 1/8
3/8 to 1/8
3/8 to 1/4
1/2 to 1/8
1/2 to 1/4
1/2 to 3/8
BuSHINg:
MALE FEMALE
PART #
FAI 110-BA
FAI 110-CA
FAI 110-CB
FAI 110-DA
FAI 110-DB
FAI 110-DC
FAI 110-EB
FAI 110-ED
FAI 110-HE
PIPE
1/4 to
3/8 to
3/8 to
1/2 to
1/2 to
1/2 to
3/4 to
3/4 to
1
to
PART #
FAI 116CA-D
FAI 116CA-E
PIPE
1/2
3/4
PIPE
1/8
1/8
1/4
1/8
1/4
3/8
1/4
1/2
3/4
PART #
FAI 100-A
FAI 100-B
FAI 100-C
PIPE
1/8
1/4
3/8
PART #
FAI 100CA-D
FAI 100CA-E
PIPE
1/2
3/4
CAP:
PART #
FAI 108-A
FAI 108-B
FAI 108-C
FAI 108-D
FAI 108-E
102
PIPE
1/8
1/4
3/8
1/2
3/4
PIPE
1/8
1/4
3/8
1/2
3/4
DVC BA794 - MHT x 1/2” FPT
DVC BA796 - MHT x 3/4” MPT
DVC FM1076 - MHT x 1” FPT
Weight: 2 oz. each
BRASS ADAPTER FEMALE gHT X MALE
NPT:
DVC BMA974 - FHT x 1/2” MPT
DVC BMA976 - FHT x 3/4” MPT
DVC IM7610T - FHT x 1” MPT
Weight: 2 oz. each
BRASS ADAPTER MALE gHT X MALE
NPT:
DVC BA73 - MHT x 3/8” MPT
DVC BA74 - MHT x 1/2” MPT
DVC BA776 - MHT x 3/4” MPT
Weight: 2 oz. each
EXTRuDED 45° STREET ELBOW:
BRASS gHT X gHT ADAPTERS:
45° STREET ELBOW
(CAST BRONzE):
Female:
DVC BA977- FHT x FHT
not pictured
Weight: 2 oz. each
PART #
FAI X124-A
FAI X124-B
FAI X124-C
PIPE
1/8
1/4
3/8
PART #
FAI 124-D
FAI 124-E
PIPE
1/2
3/4
EXTRuDED 45° ELBOW:
PART #
FAI X105-A
PIPE
1/4
Male:
DVC BA777 - MHT x MHT
BRASS ADAPTER FEMALE gHT X
FEMALE NPT:
DVC BA974 - FHT x 1/2” FPT
DVC BA976 - FHT x 3/4” FPT
Weight: 2 oz. each
EXTRuDED CROSS:
PART #
FAI X102-B
PIPE
1/4
FORgED MALE BRANCH TEE:
PART #
FAI X106-B
PIPE
1/4
SQuARE PLug:
PART #
FAI 109-A
FAI 109-B
FAI 109-C
FAI 109-D
FAI 109-E
BRASS ADAPTER MALE gHT X FEMALE
NPT:
FORgED 90° ELBOW:
90° ELBOW (CAST BRONzE):
PIPE
1/2 NPT
FAI 113-D1-1/2 1/2
FAI 113-D2
1/2
FAI 113-D3
1/2
PIPE
1/8
1/4
3/8
90° STREET ELBOW (CAST BRONzE):
REDuCINg HEX NIPPLE:
PART #
FAI 122-BA
FAI 122-CA
FAI 122-CB
FAI 122-DB
FAI 122-DC
PIPE
1/4
FORgED STREET TEE:
PART #
FAI 107-B
PIPE
1/4
FORgED TEE:
PART #
FAI 101-A
FAI 101-B
FAI 101-C
PIPE
1/8
1/4
3/8
“KINg” SHORT SHANK SuCTION
COuPLINgS (NPSM THREAD)
Female: All Brass Including Swivel Nut
DVCBS848-1”•.50lb.
DVCFBB150-11/2”•.75lb.
DVCFBB200-2”•1lb.
DVCFBB250-21/2”•2lbs.
DVCFBB300-3”•3lbs.
DVCFBB400-4”•4lbs.
Male - All Brass
DVCBS818-1”•.50lb.
DVCMB125-11/4”•.50lb.
DVCMB150-11/2”•.75lb.
DVCMB200-2”•1lb.
DVCMB250-21/2”•2lbs.
DVCMB300-3”•3lbs.
DVCMB400-4”•4lbs.
TEE (CAST BRONzE):
PART #
FAI 101CA-D
FAI 101CA-E
PIPE
1/2
3/4
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
CAMLOCKS / COUPLERS
Flo Couplings products are cost-saving,
lightweight and fast connecting, with easy
working cams.
gHT QuICK COuPLERS
DVC DgH7P
Male Plug X Male gHT, 150 MAX PSI
DVC DgH7C
Female Coupler X Female gHT, 150
MAX PSI
FAIRVIEW BRASS
gHT “Y” Coupler.
FAI 202W
QuICK COuPLINgS
Brass Straight Through Quick-Connect Fittings
NY-glass
• Yellow corrosion resistant
• Won’t go “out of round” if dropped.
• Won’t easily cross thread
• Weight is 1/6 that of brass, 1/2 of aluminum.
uSE N SuFFIX FOR NY-gLASS.
• White Food Grade couplings
• Lightweight
• Easy to install
• Many styles available
uSE F SuFFIX FOR FOOD-FLO.
Only NY-Glass
components are pictured.
Food-Flo
Size
NY-glass
TYPE A
1/4”
3/8”
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
MALE ADAPTER X FEMALE N.P.T.
FLO-025-A-N
FLO-037-A-N
FLO-050-A-N
FLO-075-A-N
FLO-075-A-F
FLO-100-A-N
FLO-100-A-F
FLO-125-A-N
FLO-150-A-N
FLO-150-A-F
FLO-200-A-N
FLO-200-A-F
TYPE B
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
FEMALE COuPLER X MALE N.P.T.
FLO-050-B-N
FLO-075-B-N
FLO-075-B-F
FLO-100-B-N
FLO-100-B-F
FLO-125-B-N
FLO-150-B-N
FLO-150-B-F
FLO-200-B-N
FLO-200-B-F
TYPE C
1/2”
5/8”
3/4”
1”
1 1/4”
1 1/2”
2”
FEMALE COuPLER X HOSE SHANK
FLO-050-C-N
FLO-062-C-N
FLO-075-C-N
FLO-075-C-F
FLO-100-C-N
FLO-100-C-F
FLO-125-C-N
FLO-150-C-N
FLO-150-C-F
FLO-200-C-N
FLO-200-C-F
TYPE D
1/4”
3/8”
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
FEMALE COuPLER X FEMALE N.P.T.
FLO-025-D-N
FLO-037-D-N
FLO-050-D-N
FLO-075-D-N
FLO-075-D-F
FLO-100-D-N
FLO-100-D-F
FLO-125-D-N
FLO-150-D-N
FLO-150-D-F
FLO-200-D-N
FLO-200-D-F
D
TYPE E
1/2”
5/8”
3/4”
1”
1 1/4”
1 1/2”
2”
MALE ADAPTER X HOSE SHANK
FLO-050-E-N
FLO-062-E-N
FLO-075-E-N
FLO-075-E-F
FLO-100-E-N
FLO-100-E-F
FLO-125-E-N
FLO-150-E-N
FLO-150-E-F
FLO-200-E-N
FLO-200-E-F
E
TYPE F
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
MALE ADAPTER X MALE N.P.T.
FLO-050-F-N
FLO-075-F-N
FLO-075-F-F
FLO-100-F-N
FLO-100-F-F
FLO-125-F-N
FLO-150-F-N
FLO-150-F-F
FLO-200-F-N
FLO-200-F-F
TYPE DP
3/4”
1”
1 1/2”
2”
DuST PLug
FLO-075-DP-N
FLO-100-DP-N
FLO-150-DP-N
FLO-200-DP-N
FLO-075-DP-F
FLO-100-DP-F
FLO-150-DP-F
FLO-200-DP-F
TYPE DC
3/4”
1”
1 1/2”
2”
DuST CAP
FLO-075-DC-N
FLO-100-DC-N
FLO-150-DC-N
FLO-200-DC-N
FLO-075-DC-F
FLO-100-DC-F
FLO-150-DC-F
FLO-200-DC-F
MALE NPT COuPLERS
DVC STMC2 - 1/4”, 4500 PSI
DVC STMC3 - 3/8”, 2700 PSI
DVC STMC4 - 1/2”, 2500 PSI
DVC STMC6 - 3/4”, 2000 PSI
FEMALE NPT COuPLERS
DVC STFC2 - 1/4”, 4500 PSI
DVC STFC3 - 3/8”, 2700 PSI
DVC STFC4 - 1/2”, 2500 PSI
DVC STFC6 - 3/4”, 2000 PSI
MALE NPT ADAPTERS
DVC STMP2B - 1/4”, 4500 PSI
DVC STMP3B - 3/8”, 2700 PSI
DVC STMP4B - 1/2”, 2200 PSI
DVC STMP6B - 3/4”, 1700 PSI
FEMALE NPT ADAPTERS
DVC STFP2B - 1/4”, 4500 PSI
DVC STFP3B - 3/8”, 2700 PSI
DVC STFP4B - 1/2”, 2200 PSI
DVC STFP6B - 3/4”, 1700 PSI
INSuLATED WATER NOzzLE
Heavy duty brass valve & adjusting
nut. Chrome plated all zinc body.
Industrial strength nylon handle.
Rubber head guard on threaded
GHT front version. Hot water up
to 180°F.
DVC SN75
CAMPBELL BRASS FOOT VALVES
Abrasion resistant. Certified red brass castings,
s.s. springs, non-corrosive nylon stem guide & s.s.
screen. For pump suction hoses.
gRA 36Y052 - 3/4” Female pipe thread
gRA 36Y053 - 1” Female pipe thread
gRA 36Y054 - 1 1/4” Female pipe thread
gRA 36Y055 - 1 1/2” Female pipe thread
gRA 36Y056 - 2” Female pipe thread
SuCTION HOSE STRAINERS
Nickel plated, standard threaded type.
DVCRHS20-11/2”FPT•11/2lbs.
DVCRHS25-2”FPT•2lbs.
DVCRHS30-21/2”FPT•21/2lbs.
Other strainer styles & sizes
available by special order
Larger sizes available by special order.
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
A
B
C
F
DP
DC
103
BOOM COMPONENTS
WE ARE SPRAYER EXPERTS! one-stop shopping for all Your spraYer neeDs.
Call OESCO, Inc. for sprayer parts, accessories & calibration. We are always happy to help you!
Qj360C NOzzLE BODY SERIES
• Available with either 3, 4 or 5 spray positions for easy change of spray tips or quick boom flushing
• Positive shutoff between each position
• Automatic spray alignment using flat fan spray tips
• Maximum operating pressure of 300 PSI (20 bar)
FOR DRY BOOMS
FOR WET BOOMS
SINgLE NOzzLE BODIES FOR DRY BOOMS
SINgLE NOzzLE BODIES FOR WET BOOMS
Available in 20 mm, 25 mm, 1/2”,
3/4” or 1” single or double hose
shanks
Available in 20 mm, 25 mm, 1/2”, 3/4”
or 1” pipe connections
for 3/8”, 1/2” and 3/4” hose
Qj100 Series
Quick TeeJet
Nozzle Body
Qj200 Series
Diaphragm Check
Valve Quick TeeJet
Nozzle Body
for 1/2”, 3/4” and 1” pipe mount
Qj300 Series
Diaphragm Check
Valve Quick TeeJet
Nozzle Body
Type Qj22187-NYB
Diaphragm Check
Valve Quick TeeJet
Nozzle Body (side mount)
Type Qj17560A-NYB Type Qj7421-NYB
Diaphragm Check
Quick TeeJet
Valve Quick TeeJet
Nozzle Body
Nozzle Body
QuICK TEEjET CAPS AND ADAPTERS
HOSE SHANK
NOzzLE BODIES
CLAMPS
QuICKjET
ROuND CLAMPS
For Operating Pressures up to
125 PSI (9 bar)
Brass, stainless steel,
Nylon and Celcon®/ stainless
steel hose shank nozzle bodies.
Features 11/16”-16 TeeJet
threaded outlet.
QuICKjET
SQuARE CLAMPS
STANDARD CLAMPS
for dry booms available for
round or square tubing.
Single Hose Connection
CAPS
STANDARD TEEjET
THREADED CAPS
Brass
Double Hose Connection
104
Nylon
Available in brass, SS or nylon.
CALL FOR YOuR
COMPLETE
TEEjET CATALOg
TODAY!
USEFUL FORMULAS
(Per Nozzle)
GPM
=
GPA x MPH x W
5,940
GPM
(Per Nozzle)
=
GAL/1000FT2 x MPH x W
MPH x W
GPA
GAL/1000FT2
(per nozzle)
= 5,940 x GPM
MPH x W
=
136 x GPM (per nozzle)
MPH x W
gPM............... Gallons per minute
gPA................ Gallons per acre
gAL/1000FT2 Gallons per 1000 square feet
MPH................ Miles per hour
W.................... Nozzle spacing (inches) for
broadcast spraying
Spray width (inches) for single
nozzle, band spraying or boomless
spraying
Row spacing (inches) divided by
number of nozzles per row for
directed spraying
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
RESPIRATORS
FOR SUPERIOR QUALITY, SAFETY, FIT, COMFORT & AVAILABILITY OF PARTS,
WE RECOMMEND nORTH®
NORTH 7700 SERIES HALF MASK RESPIRATOR
NORTH RU6500 FULL FACEPIECE RESPIRATOR
Dual elasticity head straps provide a secure fit. Medical grade silicone
facepiece is flexible, soft & secure on face. Wide contoured sealing
area fits a wide variety of facial types. Cradle suspension system sits
securely on the head, & provides an even seal without pressure points.
NIOSH approved.
SET 770030L-SET
Large
SET 770030S-SET Small
SET 770030M-SET Medium
Silicone facepiece and seal provides comfortable and secure fit.
Polycarbonate lens provides wide field of vision. Wide viewing
area provides distortion free visibility & optical clarity. Threaded
cartridge connector secures cartridges & filters to avoid accidental
disconnections. 5-point head strap w/ easy glide straps for quick,
secure donning and removal. NIOSH approved with PAPR &
Supplied Air for greater flexibility in the workplace.
SET RU65001S-SET Small
SET RU65001M-SETMedium
SET RU65001L-SET Large
All respirator sets come with
2 cartridges, 2 filters and 2 retainers
SPARE CARTRIDGES, FILTERS & RETAINERS
Cartridges
N75001L
cartridges
The organic vapor cartridges
(N75001L) are thread mounted
to the respirator. The cartridge
should be replaced when no longer
serviceable as determined by the
owner and/or supervisor, or an
OSHA change schedule, or earlier if a contaminant is detected by
smell, taste, irritation or if there is damage to the cartridge. Always
replace cartridges in pairs. Store cartridges in a sealed containment
device (bag) to insure longer cartridge use. NIOSH approved.
SPE N75001L (includes 2 cartridges)
Filters
Filters (T117010) are mounted to the
cartridge using a filter retainer
(N750036). Filters should be replaced
when no longer serviceable, TBD by
owner and/or supervisor or when
damaged, soiled, contaminated with
water, or causing increased breathing
resistance & discomfort. Filter
replacement is normally 2x as frequent
as the cartridge. NIOSH approved.
SPE 7506R95 (each - order 2 per respirator)
SPE 14900975 (each - order 2 per respirator)
retainer
filter
cartridge
NORTH 5500 SERIES HALF MASK RESPIRATOR
Economically priced, thermoplastic elastomer half mask that doesn’t
sacrifice comfort and fit. Ideal as an economical respirator for
occasional users. Latex free, no latex allergens. NIOSH approved.
SET 550030S-SET Small
SET 550030M-SET Medium
SET 550030L-SET Large
SAF-T-FIT® Plus
• Foil sealing flange and exhalation valve
• Nose bridge for increased comfort and fit
• Lightweight, humidity-resistant,
latex-free media for lower
breathing resistance:
60% improvement in measured
fit factors
42% lower exhalation breathing
resistance
34% lower inhalation breathing
resistance
• NIOSH-approved N95 protection
SPE 14110428- M/L
SPE 14110429- XL
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
inside
outside
105
PERSONAL PROTECTION
DISPOSABLE PROTECTIVE APPAREL
COVERALLS
A70®COVERALLS
Lightweight, breathable fabric that
is strong and abrasion-resistant for
extended wear. Good protection
against dry particulates & light
liquid sprays. Ideal for general
maintenance, cleanup food
processing & dusty environments.
Not normally used for spraying.
Zipper front style, no hood. 24 per
case. Also sold individually. White.
No hood.
KIM 49002 - Medium
KIM 49003 - Large
KIM 49004 - XLarge
KIM 49005 - XXLarge
A polyethelene-coated fabric.
Lightweight & resistant to
many water-based liquids,
greases, oils, liquid splashes
& sprays. CA approved
for protection in pesticide
applications. Use when
warning label reads “chemical
resistant garment when
spraying or mixing is required
by label”. Liquid-resistant
extra long zipper and taped
storm flap. Made with NFPA
99 compliant antistatic
material; includes coveralls
with hood. Yellow. Hooded.
KIM K4509812 - Medium
KIM K4509813 - Large
KIM K4509814 - XLarge
KIM K4509815 - XXLarge
SELECT COVERALLS
A strong and breathable 3-layer
fabric designed to offer protection
against fine dusts, fibers & low
SIzE CHART
surface liquid splashes.
CA approved for pesticide
application garment. Ideal for
painting, spraying, maintenance,
& handling grease & oils. Denim
Blue, 24 per case. Zipper front,
elastic back wrists & ankles.
Hooded & non-hooded.
NO HOOD
KIM 58502 - Medium
KIM 58503 - Large
KIM 58504 - XLarge
KIM 58505 - XXLarge
HOOD
No Hood
KIM 58512 - Medium
KIM 58513 - Large
KIM 58514 - XLarge
KIM 58515 - XXLarge
Hood
Note: If pesticide warning label reads “coveralls required” KleenGuard or
Kleenguard Select are acceptable. If warning label reads “chemical resistant
garment required,” Repel is the fabric to use.
Special Note: For blood borne pathogen rated garments use KleenGuard
Ultra, available by special order only. Other styles and garments available by
special order.
jACKET & BIB OVERALLS
Heavy ribbed PVC w/ soft, blended polyester/nylon lining. Stitched welded seams. Non-conductive,
non-corrosive hardware. Material stays pliable in cold temperatures. Excellent all weather suit for multiple
applications.
Alpha Size
Numerical Size
Jacket features snap-on
drawstring hood. Snaps at wrist.
No underarm vents.
Sizes: M, L, XL, 2XL
RIV 600j
106
Medium
40-42
Large
44-46
XLarge
48-50
XXLarge
52-54
Chest
44
48
52
58
60
Sleeve
27
28
29
30
31
Length
30
30
30
30
30
Overalls Waist
and
Inseam
Pants
36
38
42
46
48
28
29
30
32
32
jackets
Bib overalls have elastic in straps.
Snaps at ankle. No fly.
Sizes: M, L, XL, 2XL
RIV 600BP
Small
36-38
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
EYE / EAR PROTECTION
DISPOSABLE
EAR PODS
CA foam plug
provides excellent
attenuation. Visually
easy to monitor.
Multi-lingual
packaging. Easy to
insert correctly with
a tapered shape, slow expansion rate. Rated
NRR of 32 dB.
ELV EP-251 - Box, 200 pair
ELV EP-253 - Box-corded, 100
EAR PODS
HIgH PERFORMANCE MuFF
Provides excellent full spectrum attenuation
as well as superb low noise reduction. Fork
type headband for even distribution of
pressure, & a soft padded head cushion
for optimal comfort. With improved balance &
extra deep ear cups. Tests 29 dB NRR.
ELV HB-650 • 11 oz.
SYNC™ DIgITAL AM/FM RADIO
W/ AuDIO INPuT FOR MP3
These earmuffs deliver superior AM/FM
sound, while lightweight design & cushioned
headband ensure superb comfort for all-day
wear. Flexible antenna provides high-quality
reception and is built to stand up to work
environments.
• High quality AM/FM radio reception
• Volume does not exceed 82 dB
• 10 station memory presets
• Audio input jack; 3.5 mm cable included
• Digital AM/FM tuning with LCD display
• Cushioned headband for all-day comfort
• Reinforced fork slides: easy, comfortable fit
• Snap-in ear cushions: easy replacement
• 111-hour battery life from two (2) AA
batteries included
SPE RWS-53012 • 20 oz.
VISIONAIRE® gOggLE
High performance goggle with polycarbonate
lens and inside anti-fog treatment, four
ventilation slots, extra wide strap - all with
a comfortable fit. Meets ANSI Z87 safety
standards.
ELV gg-30-AF • goggle
ELV RL-30-AF • replaceable lens
One of our customers found these for us!
Smooth & ergonomic
pods fit into the ear for
maximum protection.
Band design prevents
ear pods from
touching dirty or
contaminated surfaces
when set down.
NRR 27 dB.
SPE QB1HYg - band
SPE QB100HYg - replacement pods
SG-14C
SG-14G
VALuEMuFF™
A basic ear muff at a very reasonable price!
Comfortable, great looking with a noise
reduction rating of 25 dB. Soft & pliable
SuperSeal ear cushions & a solid, durable
ELV HB-25 • 8 oz.
headband.
XENON™
Lightweight stylish safety glass with rubber
nose bridge and colorful rubber inserts at
temples. A good looking pair of glasses.
Tested to ANSI Z87.1-2003.
0.8 oz.
ELV Sg-14B - ice blue
ELV Sg-14C - clear
ELV Sg-14g - gray
ELV Sg-14M - flash mirror
XTS™ SAFETY gLASSES
The Extraterrestrial (XTS) offers updated
design, great fit & coverage. Ballistic Vo
rated, complies with ANSI Z87.1-2003. Antislip rubber temple tips & choice of frame
colors. 99% coverage against UV light.
Hardcoat PC lens. A best seller & a top of the
line safety glass. 1 oz.
ELV Sg-24-I/O - indoor/outdoor
ELV Sg-24M - silver coated
BIFOCALS
A brilliant idea: combining safety glasses
and a reader! These are some of the best out
there. Comfortable with a soft rubber nose
bridge & temple inserts. Available in three
lens variations in a golden brown frame.
Complies with ANSI Z87.1. 1.2 oz.
ELV RX-350C-1.5 - Bifocal strength
ELV RX-350C-2.0 - Bifocal strength
ELV RX-350C-2.5 - Bifocal strength
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
107
GLOVES
CHEMICAL gLOVES
ANSELL DISPOSABLE NITRILE
gLOVES
100% Nitrile – no fillers or additives. 4.7
mil thick (palm), 5.6 mil (fingers). Gloves
have 3X the puncture resistance of latex or
vinyl. Component materials comply with
FDA regulations for food contact. Lightly
powdered on the inside. 100 gloves/box.
Fits either hand.
EDM 92-500
S, M, L, XL
ANSELL REuSABLE NITRILE
gLOVES, 13” & 18”
These chemical and solvent resistant
gloves are lightly embossed for added
tactile touch. Long cuff and unlined.
Available in 2 lengths.
EDM 37-155
13” gloves, 15 mil thick.
Men’s XS, S, M, L, XL
EDM 37-185
18” gloves, 22 mil thick.
Men’s S, M, L, XL
THERMAL gRIP gLOVES
Lined Gripping gloves – great for picking
up wet materials, fall cleanup and other
damp working conditions. Tree growers
love them! Has a sure-grip palm with a
breathable back. 100% acrylic knitted shell
with Latex coated palm.
KCO 1790
Men’s
S, M, L, XL
(Black)
KCO 1790W Women’s S, M
(Gray)
LIgHTWEIgHT gRIPPINg
gLOVES
Breathable, gray poly/cotton knitted shell
with blue latex coated palm. Comfortable
elastic knit wrist and a great choice when
you need a lighter weight glove with
a good grip.
KCO 1791
Men’s
S, M, L, XL
NITRILE gRIPPINg gLOVES
18” PVC gLOVES
Long 18” gauntlet, smooth PVC gloves with
cotton interlock lining. The long gauntlet
provides added protection. Black.
KCO 7388L
Men’s Large Only
14” PVC gLOVES
Long 14” gauntlet, non-slip PVC gloves with a
thermal foam lining. Florescent orange; useful
when working with high temperature liquid.
KCO 4184L
Men’s Large Only
LEATHER gLOVES
LEATHER PALM gLOVES
Strong, grain pigskin leather marks
the trait of a remarkable all-purpose
glove. Leather dries soft. Unlined.
Available in rubberized cuff or knit wrist.
Best glove out there!
KCO 1917
S, M, L, XL
Open Cuff
KCO 1917KW S, M, L, XL
Knit Wrist
A nylon, breathable knitted shell with a
smooth finish and Nitrile coated palm and
fingers. Excellent for garden tasks, driving
equipment or when you find yourself in
a situation needing a form fitting glove.
Machine washable.
KCO 1890
Men’s
S, M, L, XL
NEW!
CuT RESISTANT gLOVES
Our cut resistant thread knit shell glove
has a Level 3 blade cut resistance
(EN 388:2003) with a Latex coated
palm for effective gripping and extra
protection. 55% Latex/45% Kevlar®. The
CUTFLECTOR™.
KCO 1791K Men’s
S, M, L, XL
NEW!
FROST BREAKER gLOVES
These are nitrile coated gloves with a
100% heavy thermal acrylic knit shell
providing warmth in extreme conditions.
High visibility green for safety.
KCO 1875
Men’s
M, L, XL
LINED LEATHER PALM gLOVES
Innovators of “The Original” lined
grain pigskin leather, this glove has a
trademarked material back and cuff
with the warmth of a Heatkeep™ lining.
Compared to cowhide pigskin will stand
up to twice the abrasion and wear.
Available in rubberized cuff or knit wrist.
KCO 1927
M, L, XL
Open Cuff,
Lined
KCO 1927KW S, M, L, XL
Knit Wrist,
Lined
108
LINED PIgSKIN gLOVES
Heatkeep® lined pigskin grain/suede gloves
are great for wind protection. Snug knit wrist,
keystone thumb.
KCO 94HK
Men’s
S, M, L, XL
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
GLOVES
• naturally durable
• purely refined
• total comfort
TOugH gLOVE
Tough Mud is a soft, durable and
breathable nylon shell coated with tough
nitrile offers excellent grip and wear
resistance. Provides superior dexterity for
detailed work. It’s the perfect glove for
planting seeds, working with hand tools,
operating big equipment or any
task requiring exacting dexterity.
Machine washable.
WCg 026R
Red XS, S, M, L, XL
WCg 026MS Gray XS, S, M, L, XL
BAMBOO gLOVES
This is a really nice fitting glove with an
elastic, snug-fit knit wrist. Very
inexpensive. They are made with latex
coated palm and fingers with a purple
bamboo thread knit shell. Comfortable &
environmentally friendly. Women’s sizes.
KCO 1781W Purple
S, M, L
NITRILE gLOVES
MuD H2O
The H2O offers a seamless knit shell
with a full coating of latex (to the wrist),
making it form fitting and flexible while
keeping hands dry. The palm is double
coated with micro-surface latex,
creating a superior grip for working
with tools in wet & muddy conditions.
Machine washable, waterproof.
WCg 027B
Blue XS, S, M, L, XL
gRIP gLOVE
West County Gloves. GRIP gloves
are made with 30% recycled
yarn. The durable double-dipped
foam Nitrile palm is waterproof,
extremely abrasion resistant, and
unlike the competition, provides
a solid grip wet or dry. The Grip
glove is ideal for potting, planting
and all DIY projects that require
increased dexterity and tactility.
Lightweight, breathable shell.
Machine washable. Unisex sizing.
WCg 030A
Apricot
XS, S, M, L, XL
WCg 030SA Slate
XS, S, M, L, XL
A nylon, breathable knitted shell with a
smooth finish and Nitrile coated palm and
fingers. An excellent and durable glove for
garden planting and weeding; form fitting
and washable. Women’s sizes. New color!
KCO 1891W Green
S, M, L
NEW!
ROSE gLOVE
The new rose tender glove is
constructed of strong yet supple
pigskin leather with an extended
durable nylon cuff. Reinforced with
synthetic black leather on finger tips
and palm. Puncture resistant and
terrific when you are heading into a
tough pruning job! Women’s sizes.
KCO 2103
Gray with black
S, M, L
GLOVES FOR KIDS, JUST LIKE YOURS!
LINED WORK gLOVES
Lined soft ultra suede palm material and
trademark striped back.Knit wrist and warm,
fleecy lining for cold weather.
KCO 1927KWC
Ages 3-6
KCO 1927KWY
Ages 7-12
COWHIDE LEATHER PALM gLOVES
NEW!
TOuCH SCREEN gLOVES
Keep your hands warm while using
touch screen devices. We tried it on our
own cell phones and it worked! 85%
acrylic with a little bit of spandex
to insure a good fit. Spot clean only.
KCO 21
Black
1 Adult Size
Gray cowhide leather palm with rubberized
safety cuff and wing thumb. Terrific first work
glove!
KCO 1500C
Ages 3-6
KCO 1500Y
Ages 7-12
LATEX DIPPED gLOVES
Green latex palm and fingers with comfortable
cotton shell. Get the kids planting and keep
their hands clean!
KCO 1785C
Ages 3-6
KCO 1785Y
Ages 7-12
OESCO, Inc. Route 116, Conway, MA 01341 • 413-369-4335 • 800-634-5557 • Fax 413-369-4431
www.oescoinc.com email: info@oescoinc.com
109