pico interactive instruction manual

unboxing
setup
first
rinse
Pro
ferment
your beer
dry
hopping
rack &
carbonate
serving
Clicking on the PicoBrew logo will take you
back to the Table of Contents.
after
brewing
You can navigate through chapters by
clicking on the tabs here.
let's
brew
pico
interactive
instruction
manual
usage &
care
sous vide
glossary
pico
instruction
manual
Pro
craft
beer
your
way.
Produced by:
PicoBrew Inc.
2121 N 35th St.
Seattle, WA 98103
www.picobrew.com
© 2017 PicoBrew
All rights reserved. No part of this publication may be reproduced,
stored in retrieval systems or transmitted in any form or by any means
electronic or mechanical, including, photocopying, record or any
information storage and retrieval systems, without the written permission
in writing from the copyright owners.
Printed and bound in Seattle, WA, USA
important
safety
information
•
Exercise common sense while operating the Pico.
•
Always use the keg cozy to shield the hot metal of the keg.
•
Close supervision is needed when used around children.
•
Allow machine to fully cool before removing or replacing parts.
•
Do not operate with a frayed cord or broken plug.
•
Do not remove Step Filter from the Pico unless in pause
mode or brew cycle is completed.
•
The Step Filter and contents may be hot when
removing from the machine.
•
Do not immerse or soak the machine.
•
Make sure all hoses are connected properly
before starting a brewing, rinse, or cleaning cycle.
•
To avoid risk of electrical shock hazard do not disassemble
the Pico. There are no user serviceable parts inside.
•
Various surfaces can get extremely hot during the
brewing cycle, use caution when handling the keg,
hoses and components.
•
Do not remove the hose clamps, hot liquid spray may result.
•
Do not remove the keg attachments while brewing.
•
The product is intended for household use only.
•
The appliance is not to be used, or played with, by children.
•
The appliance is not be to be used by persons with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
•
If the power supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified person in
order to avoid a hazard.
•
Per FCC 15.19(a)(3) and (a)(4) This device complies with Part 15 of
the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
•
Per FCC 15.21 Change or Modifications that are not expressly
approved by the manufacturer could void the user’s authority to
operate the equipment.
•
Per RSS-Gen, Section 8.4 This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may
cause undesired operation of the device.
•
Par RSS-Gen, Section 8.4 Cet appareil est conforme à Industrie
Canada exempts de licence standard(s) RSS. Le fonctionnement est
soumis aux deux conditions suivantes: (1) ce dispositif ne peut pas
provoquer d'interférences et (2) cet appareil doit accepter toute
interférence, y compris les interférences qui peuvent causer un
mauvais fonctionnement de l'appareil.
table of
contents
introduction
₈
unboxing
₁₀
setup
₁₉
First rinse
₂₇
let's brew
₃₇
after brewing
₄₉
fermentation
₅₉
dry hopping
₇₅
rack & carbonate
₈₁
serving
₁₀₉
usage & care
₁₁₉
sous vide adapter instructions
₁₅₈
glossary
₁₇₅
welcome
to the
easiest
countertop
brewing
appliance,
ever.
seriously.
it's really
easy to use.
8
this is your new
best friend.
(it makes beer)
pico pro instruction manual
9
BOX 3
unboxing
ACCESSORIES BOX
setup
pico
unboxing
guide
Pro
BOX 1
BOX 2
BOX 5
BOX 4
METAL KEG LID
(ATTACHED TO KEG)
METAL KEG LID
(ATTACHED TO KEG)
STEP FILTER LID
sous vide
RED FAST
FERMENTATION
ADAPTER
Note: Some international units may have the Plug
Adapter located inside the main shipper box instead of
attached to the Pico unit itself. Keep Pico Appliance Box
and inserts for warranty.
usage &
care
RED FAST
FERMENTATION
ADAPTER
STEP FILTER
Inside your Pico Pro system box you will find 4 smaller
boxes:
- Pico Appliance
- Accessories
- 2 x 1.75G Keg (for brewing and serving)
serving
1.75G KEG
rack &
carbonate
1.75G KEG
You are about to experience the joy of homebrewing using
Pico, the most advanced homebrewing appliance in the
world! We know you’re eager to get started so let’s make
sure you have everything to brew and that each item
arrived in perfect condition.
dry
hopping
PICO
congratulations!
ferment
your beer
1.75G KEG BOX
after
brewing
1.75G KEG BOX
let's
brew
APPLIANCE BOX
(RETAIN FOR WARRANTY PURPOSES)
first
rinse
PICO SYSTEM BOX
LAGERS
10
FERMENTATION
TEMP DECAL
pico pro instruction manual
11
glossary
FERMENTATION
TEMP DECAL
unboxing
box ₃
(h) dip tube brush
(a) transfer tube
setup
To clean your Brewing Keg Dip Tubes and
Keg Posts.
For transferring your beer from
one 1.75G Keg to another.
(i) keg brush
first
rinse
To clean your Brewing Kegs.
(j) airlock
let's
brew
For your Brewing Keg during Standard
(b) keg cozy
Fermentation.
To keep your keg warm during brewing.
after
brewing
(k) hops pak cradle
Attaches to the Transfer Tube
and Ball Lock Connector hoses
for the Rinse cycle and cleaning.
(e) keg seal stopper
(f) co2 regulator
Placed in Step Filter for sous vide.
(n) party tap
For dispensing beer from the Brewing Keg.
usage &
care
Ball Lock CO2 regulator used for racking with
CO2, forced carbonation, and dispensing.
(m) sous vide adapter
sous vide
(g) ⅜ inch threaded adapter
pico pro instruction manual
13
glossary
CO2 regulator comes with 5/8" threaded
adapter installed to use 74 gram CO2
cartridges. Use optional 3/8" adapter for
smaller 16 gram CO2 cartridges.
12
serving
Fits in Keg Seal vent hole, used only
after brewing cycle is completed
Used when Deep Cleaning to thoroughly
clean your Pico after every 3 brew sessions.
rack &
carbonate
Used on Brewing Keg while brewing and
during Standard Fermentation.
(l) cleaning tab
CLEANING
TAB
dry
hopping
(d) keg seal
ferment
your beer
The cradle for your Hops Pak,
used during the brewing cycle.
(c) black keg wands (₂)
unboxing
box ₄ and box ₅
setup
(o) 1.﫜﫚g brewing keg
For brewing, fermenting, and
dispensing your beer.
first
rinse
(p) metal keg lid
let's
brew
Attach to Brewing Keg. Gray Pressure
Relief Valve will be attached to Metal
Keg Lid upon arrival.
after
brewing
ferment
your beer
(q) red fast fermentation adapter
For your Brewing Keg during Fast
Fermentation.
dry
hopping
(r) fermentation temp decal
rack &
carbonate
(1) Ale decal. Attach to Brewing Keg to
monitor fermentation temperature.
Can be re-used for 3 batches.
serving
usage &
care
sous vide
pico pro instruction manual
15
glossary
14
you will need:
•
•
•
•
ferment
your beer
dry
hopping
•
after
brewing
•
let's
brew
•
first
rinse
•
•
•
PicoPak (sold separately on BrewMarketplace)
Wi-Fi connection (used in: Setup, Let's Brew)
Access to an internet browser
3 gallons of distilled or reversed osmosis filtered
water (used in: First Rinse, Let's Brew)
Access to clean tap water
Sterile water or vodka (used in: Ferment)
1.5 cups of 3% Hydrogen Peroxide or other foodgrade sanitizer per manufacturer instruction (used in:
Rack & Carbonate)
Large bowl, bucket, or other waste container (used in:
After Brewing, Rack & Carbonate)
Fragrance-free powdered dishwashing detergent
(used in: Usage & Care)
74g food-grade CO2 cartridge required for forced
carbonation (used in: Rack & Carbonate). Pressurized
CO2 cannot ship to some locations, register your Pico
and check online to see if your location is supported.
setup
If any boxes look damaged or parts appear to be missing,
please contact us immediately anytime via email at
support@picobrew.com. We’re here for you and want
you to have a great Pico brewing experience!
unboxing
double
check
your
supplies
and
inventory.
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
17
glossary
16
unboxing
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
estimated time:
5 minutes
glossary
19
pico pro instruction manual
18
setup
pico
setup
setup
₂
Plug the power cord into a standard grounded household
outlet. Press the power button to turn on your Pico.
unboxing
₁
Remove the gray and white protective film and the red
packing tape from Pico body and faceplate.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
21
glossary
20
Once connected, note the registration code
displayed on screen.
setup
₄
unboxing
₃
Connect to your home WiFi network by selecting it
with the Control Knob, then enter your WiFi password.
Once you enter your password, select the OK icon.
first
rinse
Go to: www.picobrew.com/newpico Sign in to
your account or create an account if you do not
already have one, and enter the registration code
displayed on your Pico.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
23
glossary
22
unboxing
setup
now it's
time to
give your
pico the
first
rinse.
after that
you are
ready to
brew!
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
proceed to next section: first rinse
sous vide
pico pro instruction manual
25
glossary
24
unboxing
setup
first
rinse
first
rinse
let's
brew
estimated time:
10 minutes
after
brewing
0.5 gallon distilled water (or reverse osmosis)
Keg Seal
Brewing Keg
Keg Wand
dry
hopping
•
•
•
•
ferment
your beer
you will need:
rack &
carbonate
serving
usage &
care
ian's
pro tip:
Clean equipment is critical
to crafting great beer.
pico pro instruction manual
27
glossary
26
sous vide
This first rinse ensures you
start brewing with a sparkling
clean Pico and accessories.
Check that the Water Reservoir stopper is in place.
This is located in the Water Reservoir in the center
back area. Add 0.5 gallon (or 8 cups) of distilled
water to the Water Reservoir. Add about 0.5 gallon
of clean tap water to the Brewing Keg. Place black
Keg Seal over the opening of Brewing Keg and press
into the center of it until it pops into place.
setup
first
rinse
Note: Do NOT use tap water inside the Pico Water
Reservoir, only use distilled water.
let's
brew
Set the Keg Seal Stopper aside, this will not be needed
until after the brew session is finished.
₂
unboxing
₁
After connecting up your Pico to the internet, wash
the Brewing Keg, Keg Seal, Step Filter, and lid with
with hot, soapy water then rinse well. The Step Filter
is located in the front of your Pico. To remove it lift it
up and slide it out. After rinsing the Step Filter and lid
slide them back into the Pico until the Step Filter clicks
into place.
after
brewing
ferment
your beer
Note: Make sure that when you remove the metal lid
from your keg that the white O-ring is not left behind
on the inside lip of the keg opening.
WATER
RESERVOIR
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
29
glossary
28
setup
₄
Use the Control Knob to select Utilities. Press Control
Knob to select First Rinse. After approximately 7
minutes the Pico First Rinse Cycle will complete.
unboxing
₃
first
rinse
Locate the post on the Brewing Keg marked “OUT” –
locate the BLACK Ball Lock Connector on the end of the
hose. Pull up on the outer plastic ring of the BLACK Ball
Lock Connector, place the Connector on the OUT keg
post, release outer plastic ring and press down firmly on
Ball Lock Connector. Press down on the Connector until it
audibly clicks into place. Repeat this procedure with the
GRAY Ball Lock Connector on the keg post marked “IN”.
let's
brew
after
brewing
ferment
your beer
FIRST RINSE
dry
hopping
rack &
carbonate
OUT
IN
serving
CLICK
usage &
care
CLICK
sous vide
pico pro instruction manual
31
glossary
30
Connect a clean Keg Wand to the BLACK Ball Lock
Connector by pulling up on the outer ring of the
Connector and inserting Keg Wand, release outer ring
and make sure it is securely connected to Connector.
Press Control Knob to begin pumping water out of
Water Reservoir and into the Step Filter.
Follow on-screen instructions and press Control
Knob between steps. Press Control Knob when
the Water Reservoir is empty.
setup
₆
unboxing
₅
first
rinse
The step filter will be mostly empty and there will be
a little over 0.5 gallons in the Brewing Keg. The Water
Reservoir will still contain almost all of the water you put
in originally. Disconnect the Ball Lock Connectors from
Brewing Keg by pulling up on the outer plastic rings and
lifting up off of Brewing Keg posts.
let's
brew
after
brewing
ferment
your beer
OUT
IN
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
33
glossary
32
Empty your Brewing Keg and Step Filter. Rinse
Brewing Keg, Step Filter, Keg Seal, and Keg Wand.
setup
₈
unboxing
₇
You are now ready to begin your first
Pico brew session!
first
rinse
The Inline Filter is a black plastic cylinder in the middle
of the Black Ball Lock Connector hose . Unscrew and
remove the Inline Filter cap. Remove the blue Inline
Filter wire mesh insert and rinse it thoroughly using
tap water. Place the Inline Filter mesh insert back into
the Inline Filter and screw the filter cap back on, finger
tight. This step should be performed after every Rinse
Cycle to ensure cleanliness and longevity of your Pico.
let's
brew
If you experience any problems during
your First Rinse, brewing session, or any
other step of the process please contact
us immediately at support@picobrew.com.
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
35
glossary
34
unboxing
setup
let's
brew
first
rinse
let's
brew
estimated time:
hands on 10 minutes
after
brewing
(total time: ₂.₅ hours)
ferment
your beer
you will need:
PicoPak
2.5 gallons distilled water (or reverse osmosis)
Hops Cradle
Brewing Keg
Black Keg Seal
Keg Cozy
dry
hopping
rack &
carbonate
•
•
•
•
•
•
serving
usage &
care
sous vide
pico pro instruction manual
37
glossary
36
Unwrap and set the Grain Pak in the front of the
Pico Step Filter, with the beer design facing the
front. Place Hops Pak and Cradle in the rear of
the Step Filter, pushed all the way to the left.
setup
2
unboxing
₁
Remove the vacuum-sealed wrapping and insert the
Pico Hops Pak all the way into the metal Hops Pak
Cradle. The fingers of the Cradle fit in the grooves
of the Hops Pak.
first
rinse
Note: It’s normal for some powder from the Grain
Pak to have shaken loose during shipping, please
discard this with the packaging.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
39
glossary
38
Open the top of the clean Brewing Keg and add 1
gallon plus 6 cups, or 11.4 lbs of distilled or reverse
osmosis water. Set the rubber Keg Seal on the keg
opening and press seal into the center of the keg
until it pops into place, sealing the keg.
setup
₄
unboxing
₃
Cover the Step Filter with the lid, with the black
Steam Deflector in the front and facing up.
When putting the Step Filter lid on make sure
all lid holes match up to all Hops Pak holes.
first
rinse
DISTILLED WATER
let's
brew
after
brewing
ferment
your beer
STEAM
DEFLECTOR
FACING UP
dry
hopping
rack &
carbonate
bill's
pro tip:
serving
usage &
care
Save the water jug!
It's opening is the perfect
size for Ball Lock Connectors
and makes a great waste
container for After Brewing.
sous vide
pico pro instruction manual
41
glossary
40
Remove the Water Reservoir lid from the top
of the Pico. Look inside and check to make sure
the black rubber Drain Plug is secured inside the
reservoir drain located in the center of the back of
the reservoir. Fill the reservoir with approximately
one gallon of distilled water. Replace the Water
Reservoir lid.
setup
first
rinse
Note: Do not use the Metal Keg Lid while brewing, only
use the rubber Keg Seal. Make sure the red stopper is
not inserted in the Keg Seal center hole while brewing.
₆
unboxing
₅
Slide the Keg Cozy over the Brewing Keg. Attach the
Pico hose with the BLACK Ball Lock Connector to the
post on the Brewing Keg marked “OUT”. Then attach the
GRAY Ball Lock Connector to the "IN" keg post.
let's
brew
after
brewing
ONE GALLON
ferment
your beer
dry
hopping
rack &
carbonate
OUT
IN
CLICK
serving
CLICK
usage &
care
sous vide
pico pro instruction manual
43
glossary
42
first
rinse
Note: This option is only available for select
PicoPaks at this time.
let's
brew
POWER
You can optionally change a beer's alcohol
percentage and bitterness from the PicoPak
defaults. To do so, turn Control Knob to the right
when screen says “Start Brewing”. This will give you
the ability to adjust the alcohol and bitterness. Once
finished, you can select Start Brewing by pressing
the Control Knob and your brew session will begin.
setup
CONTROL KNOB
₈
unboxing
₇
Press the Power Button on the front of the Pico. The
display will illuminate. Select Brew PicoPak and press
the Control Knob. The Pico will automatically detect
and display the PicoPak.
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
45
glossary
44
•
Pico heats the water using steam, and occasional
hissing or growling noises are normal. Don't worry,
Pico is not upset, only heating!
usage &
care
If you run into any issues while brewing, contact
support@picobrew.com.
serving
proceed to next section:
after brewing
rack &
carbonate
It is normal for only a small amount of liquid to
show in the bottom of the Step Filter during
brewing.
dry
hopping
•
ferment
your beer
During brew session some foam on the Keg Seal is
normal, particularly during a drain cycle. You can
wipe it off with a clean damp paper towel.
after
brewing
•
let's
brew
You can track the progress by signing in at
www.PicoBrew.com and clicking on BrewHouse.
first
rinse
•
setup
Notes:
congrats!
you can
now
sit back,
relax
and
enjoy
your
first
brew
cycle.
unboxing
₉
Pico will begin brewing and complete in approximately
2-3 hours, depending on the beer recipe and any
adjustments you might have made. You do not need to
monitor the Pico during the brew session.
good job.
sous vide
pico pro instruction manual
47
glossary
46
unboxing
setup
after
brewing
first
rinse
let's
brew
estimated time:
hands on ₉ minutes
after
brewing
(total time: 2缾 hrs)
ferment
your beer
you will need:
Keg Seal Stopper
Keg Wands
Waste container
(needs to hold approximately one gallon of liquid)
dry
hopping
•
•
•
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
49
glossary
48
Set the Brewing Keg aside to cool overnight in room
temperature and remove the Keg Cozy from the
Brewing Keg. It is normal for the Keg Seal to suction
slightly into the Brewing Keg as it cools, don't
worry it will not be pulled all the way inside. You will
need to pitch the yeast within 24 hours after brew
session is completed.
setup
first
rinse
Now remove the Step Filter from the Pico and
dump the biodegradable PicoPak into a compost
bin. Remember to keep the Metal Hops Cradle and
set it aside for future brewing sessions.
let's
brew
Wipe away any foam off the Keg Seal using a damp
paper towel. Insert the Keg Seal Stopper into the
center hole of the Black Keg Seal so that the keg is
airtight.
₂
unboxing
₁
After brewing finishes, disconnect both of the Ball
Lock Connectors from the Brewing Keg by pulling up
on the outer plastic ring of each Ball Lock Connector
and then pulling the Connector off of the post.
after
brewing
ferment
your beer
Note: The Brewing Keg will be very HOT so please
be careful and only touch the keg’s black rubber
handles.
dry
hopping
annie’s
pro tip:
rack &
carbonate
serving
Be carefull!
The Hops Cradle is hot
directly after brewing.
Give it chance to cool
before you touch it.
51
glossary
pico pro instruction manual
sous vide
50
usage &
care
PicoPaks fit perfectly
into an 8”x8” square
baking dish. Flip the Step
Filter upside down so
the PicoPak goes into
dish upside down, use
tongs to take the metal
Hops Pak Cradle out to
reuse for future brewing
sessions. Use the dish
to carry the PicoPak to
your compost bin!
first
rinse
For each Ball Lock Connector, pull up on the outer
ring of the Connector and insert a Keg Wand. Release
the ring and make sure it is properly connected to the
Keg Wand.
setup
₄
Direct the end of the GRAY Ball Lock Connector (“IN”)
Keg Wand into a waste container or directly into a
sink nearby. Press the Control Knob to start Rinse
Cycle. Pico will clear the drain line into the waste
container, then prompt you to empty the reservoir.
unboxing
₃
Rinse the Step Filter and lid with clean tap water.
Fill the clean Step Filter with approximately 1 inch
of tap water. Insert the Step Filter and lid back into
the Pico until it clicks.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
Make sure you use a big
enough waste water container!
The gallon water jug you used
to fill the machine is perfect
for this use.
53
glossary
pico pro instruction manual
sous vide
52
usage &
care
tap water
serving
bill’s
pro tip:
first
rinse
jack’s
pro tip:
setup
₆
Unscrew and remove the Inline Filter cap. Remove
the blue filter insert and rinse it thoroughly using tap
water. Place it back in the Inline Filter and screw the
filter cap back on, finger tight.
unboxing
₅
Insert the end of the BLACK Ball Lock Connector
(“OUT”) into the Water Reservoir. Press the Control
Knob to run the pump until the Reservoir has drained.
The water will be deposited into the Step Filter. To stop
the pump press the Control Knob when the Reservoir
is empty. Now press the power button on the Pico to
turn it off.
let's
brew
after
brewing
Cleaning the Inline Filter
after every brew session
is very important and will
lengthen the life of your Pico!
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
55
glossary
54
first
rinse
let's
brew
after
brewing
proceed to next section:
fermentation
setup
Note: Do NOT use the Heat Dry or Sanitize
option on your dishwasher. Condensation
or Air Dry options are fine to use.
awesome!
it would
appear
that
your pico
is clean
as a
whistle.
unboxing
₇
Remove the Keg Wands from the Ball Lock Connectors
by pulling up on the outer plastic rings. Remove the
Step Filter and lid from the Pico and rinse thoroughly
with tap water, they are both dishwasher safe.
ferment
your beer
dry
hopping
rack &
carbonate
a clean machine
means better
brewing.
serving
usage &
care
sous vide
pico pro instruction manual
57
glossary
56
unboxing
ferment
your
beer
setup
first
rinse
let's
brew
after
brewing
estimated time:
₆ minutes
Your keg of brewed wort, cooled to room temperature
Fermentation Temperature Decal
Yeast Packet
Sanitized, clean spoon
dry
hopping
•
•
•
•
ferment
your beer
you will need:
•
•
rack &
carbonate
for fast fermentation:
Metal Keg Lid
Red Fast Fermentation Adapter
serving
for standard fermentation:
Black Keg Seal
Air Lock
Sterile water or vodka
usage &
care
•
•
•
sous vide
pico pro instruction manual
59
glossary
58
Remove the black Keg Seal and Stopper from the
Brewing Keg. Stir the wort (unfermented beer)
inside the Brewing Keg with a sanitized, clean spoon
for about 30 seconds, this will help aerate the wort.
setup
Open the provided Yeast Packet and slowly sprinkle
all of the contents into the Brewing Keg. You do not
need to stir the yeast into the wort.
first
rinse
Stick the Fermentation Temperature Decal on the
outside of the cooled Brewing Keg.
₂
unboxing
₁
After brewing, allow the Brewing Keg to cool to room
temperature, this may take up to 24 hours depending
on ambient temperature.
let's
brew
after
brewing
Note: Yeast should be pitched within 24 hours of
brewing session.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
61
glossary
60
ferment
your beer
dry
hopping
you need your
beer quickly?
who doesn't?
rack &
carbonate
STANDARD FERMENTATION
after
brewing
(See steps 8-11) Confirm that a Keg Seal and Air
Lock are installed on the Brewing Keg. The wort can
properly ferment at any temperature in the Standard
Fermentation range indicated on the Fermentation
Temperature Decal.
let's
brew
for standard fermentation:
first
rinse
(See steps 4-7) Confirm that the Red Fast
Fermentation Adapter is installed in the Metal Keg Lid.
The wort can properly ferment at any temperature in
the Fast Fermentation range indicated on the decal,
however you only speed up fermentation by keeping
the keg temperature at the higher end of the range,
above standard fermentation temperatures.
setup
for fast fermentation
if you
prefer
faster
fermentation
follow
these
simple
steps
unboxing
₃
refer to the fermentation
temperature decal:
serving
usage &
care
sous vide
FAST FERMENTATION
pico pro instruction manual
63
glossary
62
Insert the Metal Keg Lid into the Brewing Keg,
confirm it is seated correctly and push down on the
locking clamp.
setup
Let the Brewing Keg stand for 3-5 minutes and then
shake it vigorously. Make sure no wort leaks from
the Keg Lid. If you see a leak, unlock the Metal Keg Lid
and ensure it is seated correctly before locking again.
first
rinse
Locate the RED Fast Fermentation adapter (it looks
like the gray one you just removed) and screw it
clockwise all the way into the pressure release hole of
the Metal Keg Lid.
₅
unboxing
₄
Locate the Metal Keg Lid and remove the GRAY
Pressure Release Valve from the lid by unscrewing it
counter clockwise.
let's
brew
after
brewing
ferment
your beer
LOCKING CLAMP
dry
hopping
rack &
carbonate
serving
usage &
care
ONLY USE RED FAST
FERMENTATION
ADAPTER
sous vide
pico pro instruction manual
65
glossary
64
Read the temperature indicated by your
Fermentation Temperature Decal on the side of
the Brewing Keg and consult the tables below to
see how long Fast Fermentation should take to
complete for your beer recipe.
setup
₇
unboxing
₆
first
rinse
beers:
Half Squeezed, Tweaties, Annie's London Pale, Pico Pale
75-84
70-74
65-69
4
4-5
5-6
ferment
your beer
days to fast ferment
after
brewing
keg temperature (f)
let's
brew
Carefully place your Brewing Keg in a temperaturecontrolled area where it will remain at the “Fast
Fermentation” range indicated on the Temperature
Decal on the Brewing Keg. It is normal for the Fast
Fermentation Adapter in the lid to occasionally release
CO2 as it builds up in the keg due to fermentation.
This occasional release may result in some bubbling
of krausen, which is the slightly sticky fermentation
foam, onto the Metal Keg Lid. If any krausen bubbles
out just wipe it off with a damp paper towel.
dry
hopping
beers:
All Others
75-84
70-74
65-69
5
5-6
6-7
serving
days to fast ferment
rack &
carbonate
keg temperature (f)
usage &
care
pico pro instruction manual
67
glossary
66
sous vide
Note: The day before you transfer your beer, move your
Brewing Keg into your refrigerator. This will cold crash the
yeast and will also help in racking the beer. Dry hopping your
beer may increase fermentation time.
unboxing
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
glossary
69
pico pro instruction manual
68
first
rinse
the chill out route.
setup
if
standard
fermentation
is more
your thing
use the
following
steps.
Fill your Airlock with sterile water (or vodka) to fill
line. The Airlock keeps the Brewing Keg properly
sealed against any wild yeast or bacteria, while still
allowing CO2 to release as the beer ferments.
setup
₉
unboxing
₈
Insert the Keg Seal into the top of the Brewing Keg.
Insert the Airlock into the Keg Seal center hole.
first
rinse
will's
pro tip:
let's
brew
after
brewing
Don't force the Airlock too
far into the Keg Seal. Insert
the Airlock up to 1/2 an
inch or until it fits tightly.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
71
glossary
70
first
rinse
let's
brew
kevin's
pro tip:
setup
11
As your beer ferments, CO2 is released through
the Airlock. The bubbling will be vigorous the
first couple of days of fermentation then slow
down. When the bubbling slows significantly or
completely stops that is when fermentation has
neared completion, (on average 10 days.)
unboxing
1節
Place your Brewing Keg in a temperaturecontrolled area where it will remain at the
“Standard Fermentation Range Temperature"
indicated on the Temperature Decal on the
Brewing Keg. Fermentation can take anywhere
from a week to several weeks depending on
the beer recipe.
after
brewing
ferment
your beer
The day before you transfer
your beer, replace your Keg
Seal and Airlock with the
sanitized Metal Keg Lid
and move your keg into the
refrigerator. This will cold
crash the yeast and will also
help in racking the beer.
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
73
glossary
72
unboxing
setup
dry
hopping
first
rinse
let's
brew
after
brewing
estimated time:
1 minute
ferment
your beer
Your keg of fermenting beer
Dry Hop Sachet
rack &
carbonate
•
•
dry
hopping
this step is optional.
certain beers will come
with a dry hop sachet.
you will need:
serving
usage &
care
sous vide
pico pro instruction manual
75
glossary
74
After 3 days, remove the Metal Keg Lid or
Black Keg Seal from the Brewing Keg. Remove
the Dry Hop Sachet from your refrigerator
and open the clear vacuum-sealed bag, do
NOT open the paper sachet bags. Place the
paper Dry Hop Sachet bags into the Brewing
Keg with your beer. The paper sachets are
designed to work inside your Brewing Keg
while preventing clogging during the racking
process.
setup
first
rinse
Store the Dry Hop Sachet packet in your
refrigerator along with the yeast when you
receive your PicoPak.
1₃
unboxing
1₂
If your PicoPak contains a Dry Hop Sachet
(packaged inside the same box with the Yeast
Packet) there is an extra step in order to dry hop
your beer to add maximum hop flavor and aroma.
let's
brew
after
brewing
ferment
your beer
HOPS
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
77
glossary
76
unboxing
setup
1₄
Replace and clamp the Metal Keg Lid or Black
Keg Seal on to the Brewing Keg and confirm it is
seated correctly on Brewing Keg.
first
rinse
Allow your beer to continue to ferment with the
Dry Hops for a minimum of 4 more days, longer
if fermentation is not yet complete.
let's
brew
proceed to next section:
rack & carbonate your beer
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
79
glossary
78
unboxing
rack &
carbonate
your
beer
setup
first
rinse
let's
brew
after
brewing
estimated time:
1₅ minutes
•
•
Your keg of completed fermented beer at room
temperature or chilled
1.5 cups of 3% Hydrogen Peroxide (or other food
grade sanitizer) and 1.5 cups of clean water
Large Bowl
Waste container
Empty Brewing Keg
Transfer Tube
Keg Wands
Gray Pressure Relief Valve
dry
hopping
rack &
carbonate
serving
•
•
•
•
•
•
ferment
your beer
you will need:
CO2 Regulator and Cartridge
sous vide
•
usage &
care
for racking with co2 and forced
carbonation:
for keg conditioning:
80
Carbonation Sugar Packet
pico pro instruction manual
81
glossary
•
Attach the keg wands to both ball fittings of the
Transfer Tube. Soak the Transfer Tube for 5
minutes in the large bowl of hydrogen peroxide
you set aside earlier. Remove the Keg Wands from
the Transfer Tube and rinse with clean water.
setup
₂
unboxing
₁
first
rinse
Sanitize the empty Brewing Keg by pouring 1.5 cups
of clean tapwater and 1.5 cups of 3% hydrogen
peroxide. Insert the Metal Keg Lid with the Gray
Pressure Relief Valve into the Brewing Keg, confirm
it is seated correctly and push down on the locking
clamp. Shake the keg and let it sit for 10 minutes.
Dump the keg contents into a large bowl and rinse the
keg with clean water.
let's
brew
proceed to next section:
rack the beer
after
brewing
Note: StarSan (available on www.picobrew.com/
BrewGear) is an effective alternative to hydrogen
peroxide. Follow all manufacturer's instructions. Use
caution while using StarSan and do not soak plastic
components in solution for more than 5 minutes. Do
not rinse after using StarSan. Don’t fear the foam!
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
83
glossary
82
unboxing
first
rinse
let's
brew
after
brewing
ferment
your beer
step 1: rack the beer
setup
rack &
carbonate
your
beer
(with co2 regulator)
dry
hopping
rack &
carbonate
*skip to page 﫞1, steps 﫚 - 﫝 if
racking with pico
serving
usage &
care
sous vide
pico pro instruction manual
85
glossary
84
setup
₂
Attach the Transfer Tube to the two Brewing Kegs by
connecting the ball locks to the OUT posts of each keg.
Connect your CO2 Regulator to the IN post of the
Brewing Keg you will be racking from.
unboxing
₁
first
rinse
let's
brew
after
brewing
Turn the CO2 Regulator counter clockwise all the
way to close the Regulator. Quickly screw a new CO2
cartridge into the Regulator. The Cartridge will pierce
through metal and you will hear a brief air sound.
Continue to screw the Cartridge into the Regulator
until you can no longer turn it. Insert the Metal Keg
Lid with the Red Fast Fermentation adapter onto the
Brewing Keg with your beer if not already on. Make
sure the Metal Keg Lid with the Gray Pressure Relief
Valve is inserted onto the Brewing Keg that you will
racking to.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
87
glossary
86
setup
₄
When racking is complete the Transfer Tube will
blow empty. Close the CO2 regulator and remove the
Transfer Tube from both kegs. Turn the Gray Pressure
Relief Valve back 90 degrees to close.
unboxing
₃
first
rinse
Pull up the Gray Pressure Relief Valve on the
Brewing Keg that you will be racking to and turn the
ring in any direction 90 degrees to relieve built up
pressure and restore a steady flow of beer. Slowly
dial the Regulator clockwise to open the Regulator
until it reaches 5 PSI to transfer your beer.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
89
glossary
88
unboxing
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
glossary
91
pico pro instruction manual
90
first
rinse
step 2:
rack your beer
with pico
setup
rack &
carbonate
your
beer
Connect sanitized Keg Wand to the GRAY Ball Lock
Connector.
setup
₆
unboxing
₅
Remove Brewing Keg from your refrigerator. From the
Pico main menu select Utilities then select Rack Beer
on the Pico display. This will provide step-by-step
instructions on screen.
Direct the GRAY Keg Wand to a waste container.
Press the Control Knob to clear the drain hose.
first
rinse
Press the Control Knob between each step.
CONTROL KNOB
let's
brew
When liquid stops flowing into the waste container
press the Control Knob to stop the pump, this
should take no more than 1 minute.
after
brewing
Remove the Keg Wand from the Ball Lock
Connector.
RACK BEER
ferment
your beer
dry
hopping
RACK BEER
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
93
glossary
92
first
rinse
let's
brew
after
brewing
Connect the Transfer Tube to the OUT post of each
Brewing Keg. Pull up the Gray Pressure Relief Valve and
turn the ring in any direction 90 degrees to relieve built
up pressure and restore a steady flow of beer.
setup
Connect the GRAY Ball Lock Connector to the Brewing
Keg IN post, this will allow the Pico to pressurize the
Brewing Keg with air.
₈
Press the Control Knob to begin transferring beer
from the Brewing Keg to the other Brewing Keg you
will use for serving. When racking is complete, the
Transfer Tube will blow empty. Press the Control Knob
to turn off the pump and stop the process. Disconnect
the GRAY ball lock connector from the Brewing Keg IN
post and the BLACK ball lock connectors from the OUT
posts of each keg. Turn the Gray Pressure Relief Valve
back 90 degrees to close.
unboxing
₇
Insert Metal Keg Lid onto Brewing Keg, if not already
on. Do NOT use black Keg Seal for the racking process.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
95
glossary
94
unboxing
first
rinse
let's
brew
after
brewing
ferment
your beer
step 2:
force carbonate
the beer
setup
rack &
carbonate
your
beer
dry
hopping
rack &
carbonate
*skip to page 10齃, steps 𥳐齃 - 𥳐﫚 if keg
conditioning
serving
usage &
care
sous vide
pico pro instruction manual
97
glossary
96
Place the Brewing Keg with attached CO2
Regulator into your refrigerator to chill and
carbonate for approximately 36 hours.
setup
1₀
unboxing
₉
After 24 hours, dial the Regulator
counterclockwise until it reaches 12 PSI.
first
rinse
Clean the Brewing Keg used for fermentation
and Transfer Tube, see Usage & Care section on
page 115.
after
brewing
Slowly dial the Regulator clockwise to open the
Regulator until it reaches 24 PSI. This is the correct
setting for most beers.
let's
brew
Close the CO2 regulator by turning it counterclockwise, all the way. If you do not currently have
a CO2 cartridge attached to the regulator, screw a
new CO2 cartridge clockwise into the regulator. The
Cartridge will pierce through metal and you will hear
a brief air sound. Continue to screw the Cartridge
into the Regulator until you can no longer turn it.
Insert the ball lock regulator connector into the
Brewing Keg IN post.
dry
hopping
rack &
carbonate
Cold is faster!
In case you didn't know
cold liquid diffuses CO2
quicker, so chill out.
ferment
your beer
jim’s
pro tip:
serving
usage &
care
sous vide
pico pro instruction manual
99
glossary
98
first
rinse
let's
brew
after
brewing
Note: It is normal after a few hours in the
refrigerator for the pressure displayed on the
gauge to drop from 24 psi to about 12 psi.
setup
1₂
You can also keep the regulator and cartridge
attached to the Brewing Keg for longer term
storage. To do so, after the initial 36-hour
carbonation period adjust the dial on the
regulator from 24 psi to 10-12 psi and maintain at
that pressure. Dial the regulator back to release
excess CO2 before serving then dial it back up to
10-12 psi. This storage method may require more
than one CO2 cartridge.
unboxing
11
After approximately 36 hours, slowly dial the
regulator counter-clockwise to close it and
release the pressure. Keep the CO2 Regulator
connected to the Keg IN post for serving your
beer with the Party Tap.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
101
glossary
100
unboxing
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
*skip to page ₉₇, steps ₉ -1₂
if force carbonating
first
rinse
step ₃:
keg condition the beer
(natural carbonation)
setup
rack &
carbonate
your
beer
serving
usage &
care
sous vide
pico pro instruction manual
103
glossary
102
setup
1₄
Insert the Metal Keg Lid with a Gray Pressure
Relief Valve to the Brewing Keg, seat it, and
clamp it down. Swirl the keg so the Carbonation
Sugar and beer are well mixed.
unboxing
1₃
After Racking is complete, remove the Metal Keg
Lid from the Brewing Keg with your beer and pour
all contents from the Carbonation Sugar packet
into to the keg.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
105
glossary
104
unboxing
setup
1₅
Set the Brewing Keg aside to carbonate in the
same area that you fermented the beer.
first
rinse
Note: The amount of time it takes to carbonate
should be about twice the amount of time it took
for original fermentation. This is based on the
carbonation being done at the same temperature
as the original fermentation.
let's
brew
after
brewing
Once carbonated, chill for at least 12 hours before
serving. Your beer is best kept refrigerated for
long term storage.
ferment
your beer
proceed to next section:
serve your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
107
glossary
106
unboxing
setup
serve
your
beer
first
rinse
let's
brew
after
brewing
estimated time:
﫚 minutes
ferment
your beer
you will need:
Your keg of cold, carbonated, delicious beer
Party Tap
CO2 Regulator
CO2 Cartridge
Keg Label
Glassware
dry
hopping
rack &
carbonate
•
•
•
•
•
•
serving
usage &
care
sous vide
pico pro instruction manual
109
glossary
108
Attach the Party Tap to the Brewing Keg by
connecting the black ball lock connector to the
Brewing Keg OUT post.
setup
₂
unboxing
₁
first
rinse
let's
brew
If you did not force carbonate your beer, take the CO2
Regulator and turn the Regulator counter-clockwise
all the way to close the Regulator. Quickly screw a new
CO2 Cartridge into the Regulator. The Cartridge will
pierce through metal and you will hear a brief air sound.
Continue to screw the Cartridge into the Regulator
until you can no longer turn it. Connect your CO2
Regulator to the IN post of your Brewing Keg full of
carbonated beer.
after
brewing
Pull the Pressure Relief Valve ring after attaching the
CO2 Regulator to release any excess pressure. Slowly
dial the Regulator clockwise to open the Regulator
until it reaches 10-12 PSI.
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
111
glossary
110
Remove the Party Tap when not serving and
refrigerate your Keg.
setup
₄
unboxing
₃
Push the Party Tap handle down to dispense beer and
release to stop dispensing. If beer is dispensing too
quickly reduce the PSI on the CO2 Regulator.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
113
glossary
112
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
glossary
115
pico pro instruction manual
114
setup
we're a really
fun crowd.
unboxing
welcome
to the
homebrew
family
let's
stop
for a
little
reflection.
your
first
of
many
beers.
the Flood
gates are now
open for more
delicious
homebrew
goodness.
cheers
unboxing
setup
usage
& care
first
rinse
let's
brew
after
brewing
estimated time:
20 minutes
ferment
your beer
recommended occurrence:
Wipe down the inside of the Water Reservoir.
•
Clean out the Inline Filter.
•
Inspect gaskets on Inline Filter, ball locks,
Brewing Keg posts.
•
Tighten Inline Filter, ball locks, keg posts.
usage &
care
•
serving
Remove Step Filter from Pico. Wipe down
any condensation that has formed inside Pico
where Step Filter usually sits.
rack &
carbonate
•
dry
hopping
Should be performed after every brewing session,
completed fermentation, or when keg is empty.
sous vide
pico pro instruction manual
119
glossary
118
•
Keg Wands
After a keg has kicked give
the keg a quick rinse with
hot water, put the lid on and
give it a good shake. This will
make clean up easier if you
can’t get to cleaning the keg
right away. Never leave old
beer in the keg to clean later!
sous vide
121
glossary
pico pro instruction manual
usage &
care
120
lindsey’s
pro tip:
serving
•
Keg Brush and Dip Tube Brush
Large-sized container
Fragrance-free powdered dishwasher detergent, or other
homebrewing cleaning agent
Racking Tube
rack &
carbonate
•
•
•
dry
hopping
All accessories used during brewing,fermentation, or
serving (Metal Keg Lid, Black Keg Seal, Fast Fermentation
Adapter, Pressure Relief Valve, Airlock, etc.)
ferment
your beer
•
after
brewing
17mm wrench
Brewing Keg
let's
brew
•
•
first
rinse
you will need:
setup
kegs should be cleaned
every time they are
done being used, after
fermenting or when
keg is emptied.
let's
start
this
adventure
with
our
brewing
keg.
unboxing
keg
cleaning:
setup
₂
Place all accessories used during brewing or fermentation
in to the container to soak. Use Keg Brush to clean all items
inside container, making sure to scrub any surface that may
have had any contact with beer.
unboxing
1
Fill a large container with ¼ teaspoon fragrance-free
powdered dishwasher detergent and enough hot tap
water to almost fill container.
first
rinse
let's
brew
after
brewing
ferment
your beer
ED
DER NT
P O WT E R G E
DE
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
123
glossary
122
setup
₄
Add 1 teaspoon of Hydrogen Peroxide and 1 teaspoon of
water in the keg wand attached to the Party Tap. Remove
the Keg Wand from the Party Tap and leave Hydrogen
Peroxide in the Party Tap line to sanitize.
unboxing
₃
Remove one of the keg wands from the Transfer Tube
and attach it to the Party Tap. Let it soak and push the
Party Tap handle down to rinse out the hose.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
125
glossary
124
setup
first
rinse
Note: If using StarSan, do not store the solution in
the Party Tap line for more than 5 minutes.
stop!
before
going
further
remove
your
brewing
keg
posts:
unboxing
₅
Store Party Tap with Hydrogen Peroxide solution
in the line until next use. Before dispensing, attach
keg wand to ball lock connector on Party Tap and
push Party Tap handle down to flush out Hydrogen
Peroxide solution.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
We recommend removing one post at a time
so that there is less confusion and chance of
putting the IN on the OUT post or vice versa
when reassembling. There are subtle notches on
the outside edges of the IN Keg Post Ball Lock in
case you want to remove both posts at one time.
usage &
care
sous vide
pico pro instruction manual
127
glossary
126
CAREFUL! There is a metal spring and valve inside
both the IN and OUT post Ball Locks, this is called
the Poppet Valve. It may jump out as soon as the
IN or OUT posts are taken off. Make sure you are
standing over a contained area, not a sink with an
open disposal or drain, nor a patterned carpet.
setup
₇
unboxing
₆
Use a 17mm wrench to remove Keg Posts.
first
rinse
OUT
let's
brew
IN
after
brewing
OUT
ferment
your beer
IN
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
129
glossary
128
The OUT post is connected to a long Dip Tube that
reaches the bottom of the keg. Remove the black
O-ring attached to this tube.
setup
₉
unboxing
₈
The IN post is connected to a short tube. Remove
the black O-ring attached to this tube.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
131
glossary
130
Inside the Brewing Keg mix ½ teaspoon
powdered dishwasher detergent with
enough hot tap water to almost fill the keg.
Place the Dip Tube in the Brewing Keg and
let soak for 10 minutes, longer if there is
hardened build-up.
setup
11
unboxing
1₀
Use the Dip Tube Brush to clean the inside of
Keg IN/OUT Posts thoroughly. Place all parts
but the Dip Tube in to container and let soak.
first
rinse
let's
brew
ED
DER NT
P O WT E R G E
DE
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
OUT
pico pro instruction manual
133
glossary
132
sous vide
IN
Rinse the Brewing Keg thoroughly with
clean water.
setup
1₃
unboxing
1₂
first
rinse
Use the Keg Brush to scrub the inside of the
Brewing Keg, making sure to get in contact with
all internal walls and crevices of keg, and the
outside of the keg making sure to get the top
opening and any spot that had contact with beer.
Use Dip Tube brush to clean the Dip Tube.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
135
glossary
134
first
rinse
let's
brew
OUT
setup
1₅
Make sure the IN/OUT keg posts are on the
correct sides and are tightened down. Remember,
the tube for the IN post is shorter than the Dip
Tube for the OUT post. The Dip Tube is slightly
angled and the end of it should almost touch the
center of the bottom inside the Brewing Keg.
unboxing
1₄
Reassemble all O-rings to their original part
locations. When reassembling the O-rings
make sure to use either water or a food-grade
lubricant to ease them back into place.
IN
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
137
glossary
136
unboxing
remeber:
never
use
any
cleaning
agent
inside
the
pico
unit.
setup
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
139
glossary
pico pro instruction manual
sous vide
138
usage &
care
Powdered detergents
or dry packs should
always be used
in containers
separate from
the Pico, like a bucket
or Brewing Keg.
unboxing
setup
pico
deep
clean
first
rinse
let's
brew
estimated time:
hands on 10 minutes
after
brewing
(total time: 45 minutes)
ferment
your beer
recommended occurrence:
Should be performed every 3 brew sessions.
dry
hopping
you will need:
1 gallon of clean tap water
0.5 gallon of distilled water (or reverse osmosis)
Brewing Keg
Keg Cozy
Keg Wands
Waste Container
1 solid dishwashing cleaning tablet
(do NOT use liquid or gel pouches or any common
homebrew cleaning agents)
rack &
carbonate
serving
usage &
care
•
•
•
•
•
•
•
sous vide
pico pro instruction manual
141
glossary
140
setup
₁
unboxing
first
rinse
deep
clean
cycle:
Pour 1 gallon of clean tap water into the Brewing
Keg. Slide the Keg Cozy over the Brewing Keg. Drop
the solid cleaning tablet into the Brewing Keg. You
can leave the keg lid or seal off during the Deep
Clean cycle.
let's
brew
Note: The cleaning tablet should ONLY go in the
Brewing Keg. Never put it or any other cleaning
agent inside the Water Reservoir or Step Filter.
after
brewing
CLEA
NING
TAB
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
143
glossary
142
setup
₃
Insert the Step Filter with lid into Pico. Turn Pico on. Click
Utilities and select DEEP CLEAN.
unboxing
₂
Connect the BLACK Ball Lock Connector to the OUT
post on the Brewing Keg. Repeat procedure with the
GRAY Ball Lock Connector to the IN post.
first
rinse
let's
brew
IN
after
brewing
OUT
DEEP CLEAN
ferment
your beer
CLICK
DEEP CLEAN
dry
hopping
CLICK
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
145
glossary
144
first
rinse
Note: The Brewing Keg will be very HOT after cleaning so
please proceed with caution and only touch the keg’s black
rubber handles.
setup
₅
Once the Deep Clean cycle begins it will take roughly 35
minutes to complete.
unboxing
₄
Pour 0.5 gallon of distilled water into the Water
Reservoir.
let's
brew
0.5 GALLON
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
147
glossary
146
setup
₆
unboxing
rinse
cycle:
first
rinse
Once Deep Clean cycle finishes, carefully dump all liquid
from both the Step Filter and the Brewing Keg. Liquid will
be HOT so use caution! Rinse thoroughly with clean water.
Fill the Step Filter with approximately 1 inch of clean tap
water, then insert the Step Filter with lid back into Pico until
it clicks into place.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
pico pro instruction manual
149
glossary
148
sous vide
tap water
Direct the end of the GRAY Ball Lock Connector (“IN”)
Keg Wand into a waste water container.
setup
₈
unboxing
₇
For each Ball Lock Connector, pull up on the outer ring
of the Connector and insert a Keg Wand, release the
ring and make sure it is properly connected to the
Keg Wand.
first
rinse
let's
brew
after
brewing
IN
ferment
your beer
OUT
dry
hopping
rack &
carbonate
serving
bill’s
pro tip:
usage &
care
pico pro instruction manual
151
glossary
150
sous vide
Make sure you use a big
enough waste water container!
The gallon water jug you used
to fill the machine is perfect
for this use.
setup
1節
Remove the Water Reservoir lid. Insert the end of
the BLACK Ball Lock Connector (“OUT”) Keg Wand
into the Water Reservoir. Run the pump until the
Reservoir is drained. When the Reservoir is empty
stop the pump by pressing the Control Knob.
unboxing
₉
Press Control Knob to start Rinse Cycle and run the
pump to clear the drain line.
first
rinse
let's
brew
CONTROL KNOB
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
153
glossary
152
setup
1₂
Unscrew and remove the Inline Filter cap. Remove
the blue Inline Filter cylinder and rinse it thoroughly
using tap water. Put the cleaned cylinder back into
the Inline Filter and screw the Filter cap back on,
finger tight.
unboxing
11
Press the power button on the Pico to turn it off.
first
rinse
let's
brew
POWER
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
155
glossary
154
unboxing
setup
1₃
Remove the Keg Wands from the Ball Lock
Connectors by pulling up on the outer plastic
rings. Remove the Step Filter and lid from the
Pico and rinse thoroughly with tap water.
first
rinse
Note: If your Brewing Keg is already being used,
use a clean container that can hold up to 1.5
gallons and can withstand temperatures up
to 135°F. The container and liquid will be hot,
so please exercise caution while handling. You
will need both Keg Wands, which will need to
be attached to the BLACK and GRAY Ball Lock
Connector hoses and directed into the container.
The Keg Wand attached to the BLACK Ball Lock
Connector will suction water out of the container,
so make sure the end is submerged enough
to suction water. The Keg Wand attached to
the GRAY Ball Lock Connector will recirculate
water into the container, so make sure its end is
directed inside the container.
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
157
glossary
156
unboxing
temp
1" Thick
1:00
129
136
154
1.5" Thick
1:30
129
136
154
2" Thick
2:00
129
136
154
1" Thick
1:30
136
143
158
boneless
chicken breast 0.5 lb
1:30
140
150
165
salmon
1" Thick
0:40
105
123
131
1-2"
1:00
105
123
131
time
soft
med
hard
0:20
167
steak
pork chop
you will need:
•
•
•
•
•
•
•
•
•
Pico, with Step Filter and its lid
Brewing Keg
Keg Cozy
Sous Vide Adapter
1 gallon of Distilled Water
Tap water
1 gallon heavy duty Ziploc® bag or a food vacuum
sealer system
Food to cook
5 quarts of tap water
rack &
carbonate
temp
dry
hopping
temp
ferment
your beer
time
size
after
brewing
well
Thick
(4)
0:40
usage &
care
0:25
serving
eggs
168
168
sous vide
recommended:
pico pro instruction manual
159
glossary
All temperatures are listed in degrees Fahrenheit.
158
let's
brew
med
first
rinse
rare
sous vide
adapter
instructions.
setup
sample
recipes:
₂
Place the black Keg Seal on the top of the Brew
Keg opening, push in the center until it pops into
place. Make sure the hole in the center of the Keg
Seal is open. Pull the Keg Cozy over the Brewing
Keg. Attach the BLACK Ball Lock Connector
hose connector to the Brewing Keg post marked
“OUT”. Repeat the procedure with the GRAY Ball
Lock Connector hose (capitalize) on the brew keg
post marked “IN”.
setup
Note: 5 Quarts = 1.25 Gallons = One Gallon + 4 Cups =
20 Cups = 10.5lbs Water = 4.75 Liters
unboxing
₁
Fill the Brewing Keg with 5 quarts of warm tap water.
first
rinse
let's
brew
after
brewing
ferment
your beer
OUT
IN
dry
hopping
CLICK
rack &
carbonate
CLICK
serving
usage &
care
sous vide
pico pro instruction manual
161
glossary
160
setup
₄
Consult the Sous Vide Recipe Table on page 156 for
the food you are cooking.
unboxing
₃
Turn the Pico on. Using the Control Knob scroll to
Sous Vide and press Control Knob to select.
first
rinse
Set the desired water temperature for cooking by
turning the Control Knob to scroll to the correct
temperature and pressing the Control Knob to
select and continue to the next step.
let's
brew
after
brewing
sous vide
ferment
your beer
dry
hopping
sous vide
water temp
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
163
glossary
162
Insert the empty Step Filter and lid into the Pico,
press Control Knob to continue to the next step.
setup
₆
unboxing
₅
Enter the cooking time of your recipe in Hours:Minutes
format by turning the Control Knob to scroll to the
correct hour or minute and pressing the Control Knob
to select and continue to the next step.
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
00:00
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
165
glossary
164
Begin preparing your food:
Trim and prepare food for cooking. Thicker cuts
of meat or vegetables may require longer cooking
time. Add any spices or aromatic to the food
before sealing the bag(s).
setup
first
rinse
Vacuum seal the food or insert into a 1 gallon
heavy duty freezer Ziploc® bag with the air
squeezed out and fully sealed.
let's
brew
after
brewing
Open the Water Reservoir lid on top of the Pico and fill
the reservoir with 1 gallon of distilled (or RO) water.
Press the Control Knob to begin heating up the water
to the designated cooking temperature. For sous vide
recipes or cooking sessions that go over 3.5 hours you
might need to add more distilled water to the reservoir
during the cooking process, check on it as needed.
₈
unboxing
₇
Make sure your keg is properly connected and filled
with 5 quarts of water, press the Control Knob to
continue to the next step.
ferment
your beer
dry
hopping
rack &
carbonate
serving
lindsey’s
pro tip:
167
glossary
pico pro instruction manual
sous vide
166
usage &
care
To get most of the air out of a Ziploc
bag seal the bag but leave about 1” of
bag unsealed. Submerge Ziploc® bag of
food in water and as the bag submerges
the water pressure will squeeze the
air out for you. Right before the bag is
fully submerged seal up that last 1” of
the bag and pull out of water. The bag
should be mostly air-tight and ready to
sous vide.
Place food bag(s) in Step Filter. If using a Ziploc®
bag, place bag(s) against the side of the Step Filter
with the top hanging out over the edge of Step
Filter. Once you place the Step Filter lid on it will
clamp the bag(s) into place. Vacuum sealed bags
should sink to bottom. If necessary, place a foodsafe object on top of bag(s) to make sure they will
stay fully submerged in the water during the entire
cooking process.
Place lid on Step Filter, clamping any Ziploc® bags
in place. Make sure the lid holes are in the correct
places (see diagram) and that the black steam
deflector is towards the front and facing upward.
setup
1節
unboxing
₉
first
rinse
let's
brew
When the water has reached cooking temperature the
Pico will beep. Press the Control Knob to silence the
alarm. Remove the Step Filter and its lid from Pico.
Place the Sous Vide Adapter in the back section of the
Step Filter so the hole on the backside of the Adapter
covers up the drain hole in the back of the Step Filter.
The tapered front of the Adapter should be facing the
front of the Step Filter. Press down so the Adapter is
firmly in place. See below diagram.
after
brewing
ferment
your beer
Insert Step Filter with lid into Pico.
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
pico pro instruction manual
169
glossary
168
let's
brew
after
brewing
ferment
your beer
dry
hopping
Note: If you do not exit after the cooking is finished
Pico will automatically hold the cooking temperature.
Any food still in the Pico will continue to cook.
first
rinse
rack &
carbonate
serving
If you plan on searing any food after cooking make sure
to prepare the pan or grill a few minutes before the
Pico is finished cooking your food. A simple way
to sear meat is to use a heavy pan on your stovetop.
Heat the pan on high until hot, add butter/oil and then
sear the meat 1-2 minutes per side until the desired
sear is achieved.
setup
When Pico is finished cooking the screen will say
“Finished” and an alarm will sound for 60 seconds.
You can turn the alarm off by pressing the Control
Knob.
When the sous vide process is finished:
• You can select “Drain” option on-screen and this
will drain water from Step Filter to Brewing Keg,
this step makes it easier to get the Step Filter out
without spilling water. Use tongs to take food out
of Step Filter.
• Or, select “Exit” on-screen and carefully remove
Step Filter from Pico, be cautious as the water
inside will be warm. Use tongs to take food out of
Step Filter.
• Cut open vacuum-sealed bag(s) or open Ziploc®
bag(s). Dispose of bag(s).
• Season food to preference. Sear on hot pan or
grill (optional).
unboxing
11
Select “Start Cooking” on-screen by pressing the
Control Knob. This will begin the sous vide cooking
process using the time and temperature you selected.
You will be able to view the temperature and remaining
cooking time on the Pico screen. If at any time you
need to pause the cooking process turn the Control
Knob to reveal the “Pause System” option and press
Control Knob to select and pause cooking. When
ready to resume cooking make sure the Step Filter is
inserted correctly then select “Continue Cooking” onscreen using the Control Knob.
usage &
care
sous vide
pico pro instruction manual
171
glossary
170
first
rinse
Thoroughly clean and rinse the Step Filter, lid, Brewing
Keg, and black Keg Seal.
setup
let's
brew
after
brewing
OUT
ferment
your beer
IN
dry
hopping
If you plan on doing another sous vide session right
away you can reuse the distilled water in the Water
Reservoir, check to see if you need to add more. If
you are not going to do another sous vide session
insert an empty Step Filter back into the Pico.
Detach the BLACK Ball Lock Connector hose from
the Brewing Keg. Attach a clean Keg Wand to the
BLACK Ball Lock Connector and direct the wand
into the Water Reservoir. Select “Start Vacuum” to
begin suctioning out the remaining water and press
the Control Knob to stop the vacuum when there
is no more water in the reservoir. Press the power
button to turn Pico off.
Unscrew and remove the Inline Filter cap attached to
the BLACK Ball Lock Connector hose. Remove the blue
filter insert and rinse it thoroughly using tap water.
Place it back in the Inline Filter and screw the filter cap
back on, finger tight.
unboxing
1₂
Disconnect both Ball Lock Connector hoses from
Brewing Keg. Dispose of water in both Step Filter
and Brewing Keg.
rack &
carbonate
serving
usage &
care
sous vide
172
pico pro instruction manual
173
glossary
Consuming raw or undercooked meats, poultry, seafood,
shellfish or eggs may increase your risk of foodborne illness.
unboxing
first
rinse
let's
brew
after
brewing
ferment
your beer
dry
hopping
rack &
carbonate
serving
usage &
care
sous vide
everything
you need to
impress
your friends
and brew
correctly.
glossary
175
pico pro instruction manual
174
setup
manual
glossary
fermentation
ale
A generic term used for beers that are created
using a top-fermenting yeast strain at a higher
temperature than lager yeast strains.
malt
A generic term used for beers that are created
using a bottom-fermenting yeast strain at a
lower temperature than ale yeast strains. Also
a term for cold-storing a beer for an extended
amount of time.
177
glossary
pico pro instruction manual
sous vide
Barley, or other grains, used during the
mash and brewing process. Contributes a
wide range of flavors from uncooked bread
to roasted coffee, depending on its kiln or
roasted level.
usage &
care
The addition of hops after initial fermentation
to increase hop aroma without increasing hop
bitterness.
lager
serving
dry hop
Thick, moussy foam on the top of fermenting
wort that occurs during the beginning of
fermentation.
rack &
carbonate
Part of the mash process where grains soak to
activate and distribute temperature-specific
enzymes.
krausen
dry
hopping
dough in
Hops are the flower cones of a the hop plant,
used to contribute bitterness, aroma, and
anti-microbial qualities to beer. Commercially
available in pellet, plugs, whole cone, or
extracted forms.
ferment
your beer
Carbon dioxide (CO₂) is a naturally occurring
by-product of fermentation. Keg Conditioning
is natural carbonation created during
fermentation when yeast metabolize sugars.
Forced carbonation is the addition of CO₂ to
the final beer.
hops
after
brewing
carbonation
Single-celled organisms that reproduce
quickly in specific environments. Integral
to specific beer styles, particularly sours,
and considered an off-flavor and flaw in the
majority of all other beer styles.
The process where yeast break down sugars
into carbon dioxide (CO₂) and alcohol.
let's
brew
Introducing oxygen into the wort to make sure
yeast can reproduce abundantly.
Aromatic flavor compound created by yeast
during fermentation. Esters contribute fruity
aromas to beers.
first
rinse
aerate
bacteria
176
esters
setup
A fermentable addition to the mash that
includes sugars, syrups, and unmalted cereal
grains such as corn, rice, oats that provide
extra sugars in the wort.
unboxing
adjunct
0.5 gallon
1.9 liters
1 gallon
3.8 liters
2.5 gallons
9.5 liters
3 gallons
11.4 liters
75-84 F
23.9-28.9 C
70-74 F
21.2-23.3 C
65-69 F
18.3-20.6 C
serving
usage &
care
Yeast that is naturally airborne and
ubiquitous. Typically used in sours or wild ales,
considered an off-flavor in a majority of other
beer styles.
sous vide
pico pro instruction manual
179
glossary
178
metric
rack &
carbonate
wild yeast
A solid material composed of yeast, proteins,
and hop particles that fall out of solution
during brewing and fermentation
imperial
dry
hopping
trub
The process of transferring beer from one keg
to another.
imperial and metric conversion table
ferment
your beer
racking
Pounds per square inch.
Single-celled fungus that breaks down
sugars in the wort during fermentation
into carbon dioxide, alcohol, and creates
various phenols or esters.
after
brewing
psi
The act of adding a small amount of sugar
to fermented beer in order to restart
fermentation and create carbonation inside
bottle or keg.
yeast
let's
brew
priming
The process of adding yeast to cooled wort to
start fermentation.
Unfermented liquid containing sugars
extracted from the malt grain during the
mash process. Adding yeast to wort starts
the fermentation process which transforms
the wort into beer.
first
rinse
pitch
Chemical compounds derived from yeast
activity during fermentation. Vary from spicy,
peppery, smoky, medicinal, and many more.
wort
setup
phenols
The process of steeping milled grains in
hot water in order to activate enzymes and
extract sugars from the malt.
unboxing
mash
we
highly
suggest
using the
following
pages to
document
your
brewing
journey.
scribble,
doodle,
record.
it's up
to you.
brewing notes
brewing notes
brewing notes
brewing notes
brewing notes
17-0519
Copyright 2017
www.PicoBrew.com
pico
instruction
manual
Download PDF
Similar pages
Smart+ Products SPP155BDSS Beer Dispenser Kegerator Quick Installation Guide
RegulatorPanelKits 1Prod1press SpecSheet
RegulatorPanelKit Secondary 1prod1press
894 83315
HighPressureRegulator CO2 0