308568E 8 HORSEPOWER, GASOLINE-POWERED

INSTRUCTIONS-PARTS LIST
308568
Rev. E
This manual contains important
warnings and information.
READ AND KEEP FOR REFERENCE.
INSTRUCTIONS
8 HORSEPOWER, GASOLINE-POWERED
GM10000 Airless Paint Sprayer
3000 psi (207 bar, 21 MPa) Maximum Working Pressure
Model 231343
This is a basic sprayer without a hose or a gun.
CAUTION
Always use a minimum hose length of 100 foot
(30.4 m) 1/4 inch ID or 50 foot (15.2 m) 3/8 inch ID.
An undersized hose may result in poor equipment
performance and damage to the clutch or pressure
control.
05058A
GRACO INC.
P.O. BOX 1441
MINNEAPOLIS, MN
ECOPYRIGHT 1995, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
55440–1441
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Component Identification and Function . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Bearing Housing & Connecting Rod . . . . . . . . . . . . . . 16
Drive Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pinion, Clutch, Clamp, Field, & Engine . . . . . . . . . . . 20
Pinion Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Field & Wiring Harness . . . . . . . . . . . . . . . . . . . . . . . . .
Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Control Replacement . . . . . . . . . . . . . . . . . .
Displacement Pump Repair . . . . . . . . . . . . . . . . . . . . .
Sprayer Parts Drawings and Sprayer Parts Lists . . .
Pinion Assembly Parts list and Drawing . . . . . . . . . .
Pressure Control Parts list . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
26
27
30
32
34
38
39
39
39
40
40
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
equipment if you do not follow the instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
INSTRUCTIONS
D This equipment is for professional use only.
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated system component. Refer to the
Technical Data on page 40 for the maximum working pressure of this equipment.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82_C (180_F) or below –40_C (–40_F).
D Do not lift pressurized equipment.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Wear hearing protection when operating this equipment.
D Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.
2
308568
WARNING
INJECTION HAZARD
Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury.
D Fluid injected into the skin may look like just a cut, but it is a serious injury. Get immediate medical attention.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 12 if the spray tip clogs and before cleaning,
checking or servicing the equipment.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not
repair high pressure couplings; you must replace the entire hose.
D Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
FUEL HAZARD
The fuel used in this unit is combustible and when spilled on a hot surface can ignite and cause a fire.
D Do not fill the fuel tank while the engine is running or hot.
EXHAUST HAZARD
The exhaust contains poisonous carbon monoxide which is colorless and odorless.
D Do not operate this equipment in a closed building.
308568
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spraying immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Disconnect all electrical equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.
D Ground the sprayer to a true earth ground with the ground wire and clamp (supplied).
D Use only electrically conductive hoses.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the sprayer.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 12 to prevent the
equipment from starting unexpectedly.
NOTE: This is an example of the DANGER label on your sprayer. This label is available in other languages, free
charge. See page 38 to order.
FIRE AND
EXPLOSION HAZARD
SKIN INJECTION
HAZARD
Spray painting, flushing or cleaning equipment with flammable liquids in
confined areas can result in fire or explosion.
Liquids can be injected into the body by high pressure airless spray
or leaks – especially hose leaks.
Use outdoors or in extremely well ventilated areas. Ground equipment,
hoses, containers and objects being sprayed.
Keep body clear of the nozzle. Never stop leaks with any part of the
body. Drain all pressure before removing parts.Avoid accidental triggering of gun by always setting safety latch when not spraying.
Avoid all ignition sources such as static electricity from plastic drop
cloths, open flames such as pilot lights, hot objects such as cigarettes,
arcs from connecting or disconnecting power cords or turning light
switches on and off.
Failure to follow this warning can result in death or serious injury.
Never spray without a tip guard.
In case of accidental skin injection, seek immediate
“Surgical Treatment”.
Failure to follow this warning can result in amputation or serious injury.
READ AND UNDERSTAND ALL LABELS AND INSTRUCTION MANUALS BEFORE USE
4
308568
Component Identification and Function
K
B
A
C
M
D
4
27
J
H
12
G
53
F
L
1
N
47
19
E
05059A
Fig. 1
A
Pressure Control Switch
ON/OFF, enables/disables clutch function
B
Pressure Adjusting Knob
Controls fluid outlet pressure
C
Air Cleaner*
Filters air entering the carburetor
D
Fuel Tank*
Holds 1.59 gallons (6.04 liters) of [(R+M)/2]; 86 octane gasoline
E
Muffler*
Reduces noise of internal combustion
F
Spark Plug Cable*
Routes electrical current to spark plug
G
Fuel Valve*
On/off valve to regulate fuel flow from gasoline tank to carburetor
H
Choke*
Enriches air/gasoline mixture for cold starting
J
Throttle*
Adjusts engine speed for large or small orifice spray tips
K
Engine Switch*
Enables/disables engine operation
L
Secondary Fluid Outlet
Second hose and spray gun is connected here
M
Pressure Control
Controls clutch cycling to maintain fluid pressure.
N
Primary Fluid Outlet
Hose and spray gun is connected here
1
Engine*
8 HP gasoline engine
4
Clutch
Transfers power from engine to drive assembly
12
Drive Assembly
Transfers power from clutch to displacement pumps
19
Displacement Pump (2)
Provides fluid to be sprayed through spray gun
27
Fluid Filter
Filters fluid between source and spray gun
47
Grounding Clamp and Wire
Grounds sprayer system
53
Pressure Drain Valve
Relieves fluid pressure when open
*
For more detailed explanations of these controls, refer to the Honda engine manual; supplied
308568
5
Setup
CAUTION
To avoid damaging the pressure control, which may
result in poor equipment performance and component
damage, follow these precautions.
1. Always use nylon spray hose. Never use a wire
braid hose; it is too rigid to act as a pulsation
dampener.
3. Fill packing nut/wetcup. Fill the packing nut/wetcup (416) 1/3 full with Graco Throat Seal Liquid
(TSL), supplied. See Fig. 2.
4. Check the engine oil level. Refer to the Honda
engine manual, supplied. This is a summary of the
information: Remove one of the oil fill plugs (M);
the oil should be almost overflowing. See Fig. 3.
Add oil as necessary.
2. Always use a minimum hose length of 100 foot
(30.4 m) x 1/4 inch ID or 50 foot (15.2 m) x 3/8
inch ID hose at each outlet.
Recommended lubrication oil: Use a high-quality,
detergent oil, SAE 10W–30, classified “FOR
SERVICE SG or SF”, for regular use and for
breaking–in a new engine.
3. Never install any shutoff device between the filter
(27) and the main hose. See Fig. 2.
4. Always use the main filter outlet (29) for a one
gun operation. Never plug this outlet.
27
53
1. Connect hose and gun. (Refer to Fig. 2.)
a. Remove the plastic cap from the 3/8 npsm (m)
filter outlet nipple (29). Screw the first 50 foot
(15.2 m) main fluid hose onto the nipple.
Connect the second 50 foot hose to the first 50
foot with a coupling nipple. Read the CAUTION, above.
34
29
b. Connect the whip end hose between the main
fluid hoses and the inlet adapter of the gun.
c.
Do not use thread sealant, and do not install
the spray tip yet!
416
WARNING
If you supply your own hoses and spray gun, be
sure the hoses are electrically conductive, that the
gun has a tip guard, and that each part is rated for
at least 3000 psi (207 bar, 21 MPa) Maximum
Working Pressure. This is to reduce the risk of
serious injury caused by static sparking, fluid
injection or over-pressurization and rupture of the
hose or gun.
2. Two gun hookup. Remove the cap (34) from the
secondary hose outlet. Connect the second outlet
hoses to the sprayer as explained in Step 1,
above.
6
308568
27 Fluid Filter
53 Pressure drain valve (below fluid filter)
34 Secondary outlet cap
29 3/8 npsm(m) primary fluid outlet
416 Wetcup
Fig. 2
05060
Setup
5. Be sure your system is properly grounded
before operating it. Connect the sprayer to a true
earth ground with the grounding wire and clamp
(47) ; for example, a cold water pipe or a ground
rod driven into the earth.
9. Keep the sprayer upright and level during
operation and whenever it is being moved. See the
CAUTION on page 10.
6. Fill the gas tank. See Fueling, page 8.
7. Flush the pumps to remove the lightweight oil
which was left in the pumps to protect them from
corrosion.
L
a. Before using water–base paint, flush with
mineral spirits, followed by soapy water, and
then flush with clean water.
K
b. Before using oil–base paint, flush with mineral
spirits, only.
c.
See Flushing on page 13 for the flushing
procedure.
8. Prepare the paint according to the manufacturer’s
recommendations.
47
a. Remove any skin that may have formed.
b. Stir the paint to mix the pigments.
c.
Strain the paint through a fine nylon mesh bag
(available at most paint dealers) to remove the
particles that could clog the filter or spray tip.
This is probably the most important step
toward trouble–free spraying.
M
05061A
Fig. 3
308568
7
Fueling
WARNING
FIRE AND EXPLOSION HAZARD
Gasoline is extremely flammable and
explosive under certain conditions.
Always turn the engine switch (K) to off
before refueling. (Fig. 3)
Refuel in a well-ventilated area.
Do not smoke or allow flames or sparks in the area
where the engine is refueled or where the gasoline
is stored.
Do not overfill the tank. Make sure the gas fill cap
(L) is securely closed after refueling. (Fig. 3)
Be careful not to spill fuel when fueling. Fuel vapor
or spilled fuel can ignite. If any fuel is spilled, make
sure the area is dry before starting the engine.
1. Fuel specifications. Use automotive gasoline
with a pump octane number [(R + M)/2] of 86 or
higher, or a research octane number of 91 or
higher. Unleaded fuel minimizes the combustion
chamber deposits.
8
308568
2. Gasolines containing alcohol (gasohol). Do not
use gasohol which contains methanol, if the gasohol does not contain cosolvents and corrosion
inhibitors for methanol. Even if it does contain such
additives, do not use the gasohol if it contains
more than 5% methanol or 10 % ethanol.
NOTE: The HONDA engine warranty does not cover
the damage resulting from the use of gasolines containing a higher percentage of alcohol than mentioned
in step 2. See the HONDA engine manual for more
information.
3. General. Do not use any oil and gasoline mixtures
or contaminated gasoline. Avoid getting any dirt,
dust or water in the fuel tank.
4. Tank Capacity. 1.59 gallons (6.04 liters). Always
leave at least 1/2 in. (13 mm) at the top of the tank
for expansion.
5. Shut off the engine before refueling.
6. After refueling, tighten the fuel tank cap firmly.
Startup
Before You Start the Sprayer
5. Move the pressure control switch to OFF.
1. See Flushing on page 12 to determine if you
should flush the sprayer.
6. To start the engine:
2. Be sure the gas tank is full.
3. Check the engine oil level.
NOTE: The engine stops automatically, or will not
start, if it is low on oil. Refer to the oil fill procedure in
the Honda engine manual or to step 4, page 6.
4. Be sure the spark plug cable is firmly pushed
onto the plug.
Starting the Sprayer
a. Turn the pressure adjusting knob all the way
counterclockwise to the lowest pressure setting.
b. Slide the metal throttle lever away from the
fuel tank to maximum position (fully left).
c.
If the engine is cold, close the choke by moving the gray lever.
d. f the engine is warm, close the choke by
moving the gray lever only half way or not at
all.
NOTE: Refer to Fig. 1 as you start the sprayer.
e. Turn the engine switch to ON.
1. When starting a sprayer that IS NOT PRIMED,
remove the spray tip.
WARNING
2. If a secondary hose and gun is not installed,
be sure the cap is securely plugging the secondary
outlet fitting.
3. Place the suction tube into the paint, water or
solvent container, depending on whether you are
flushing or are ready to spray.
4. Open the black fuel shutoff lever by pushing it in
the direction of the arrow.
CAUTION
Never try to start the engine unless fluid pressure is
relieved and the pressure control switch is OFF.
Trying to start the engine when it is pressurized
could damage the recoil system.
MOVING PARTS HAZARD
A rope which recoils too quickly may hit
someone and cause serious injury. The
rope could also jam in recoil assembly.
f.
Hold the frame of the sprayer with one hand
and pull the starter rope rapidly and firmly.
Continue holding the rope as you let it return.
Pull and return the rope until the engine starts.
g. Open the choke as soon as the engine starts,
except in cold weather. In cold weather, leave
the choke closed for 10 to 30 seconds before
opening it to keep the engine running.
7. Unlock the gun trigger safety.
308568
9
Startup
8. Prime the pumps:
a. Place the suction tube in the bucket of paint,
water, or solvent.
b. Open the pressure drain valve.
c.
Set engine speed to idle.
d. Move the pressure control switch to ON. Turn
the pressure adjusting knob to about 1/4 turn
from minimum pressure.
e. Run the pumps until fluid is flowing smoothly
from the pressure drain valve, indicating both
pumps are primed. A pulsing flow which nearly
stops indicates that one pump is not primed –
wait for a smooth flow from the pressure drain
valve.
f.
Move the pressure control switch to OFF.
g. If the pumps were primed with water or solvent, remove the suction tube from the water
or solvent and place it in the paint. Repeat
steps b through f.
h. Close the pressure drain valve.
9. When both pumps are primed:
a. Remove the spray tip.
b. Set the engine speed to full flow.
c.
Move the pressure control switch to ON. Turn
the pressure adjusting knob 1/4 turn for minimum pressure.
d. Unlock the gun trigger safety.
e. Trigger the gun into the pail until fluid flows
from the gun. If pumping solvent or solvent–
based paint, hold a metal part of the gun firmly
against a grounded metal pail.
f.
Release the gun trigger and lock the gun
trigger safety.
WARNING
INJECTION HAZARD
To reduce the risk of serious injury from
fluid injection, never operate the spray
gun with the tip guard removed.
10. Install the spray tip in the gun. See the separate
tip instruction manual, 308644, supplied.
11. Move the pressure control switch to ON.
12. Adjust the engine speed and pump pressure.
Unlock the gun trigger safety. Trigger the gun onto
a test paper to check the spray pattern and atomization. Turn the pressure adjusting knob until you
get a good pattern. Then slowly lower the throttle
setting as far as you can without changing the
spray pattern.
13. If using two or more guns, the throttle must be set
with all guns open at once. If this is not practical,
determine the optimum throttle setting by trial and
error while using the sprayer. If the sprayer cycles
while all guns are in use, lower the throttle setting
until the sprayer just barely cycles. If the pressure
drops when all guns are in use and the sprayer
does not cycle, increase the throttle setting until
the pressure returns (sprayer will probably cycle).
NOTE: Do not lower the throttle setting below the
Minimum Operating Speed.
CAUTION
Always use the lowest needed fluid pressure and the
lowest needed throttle setting, to increase the life of
the sprayer. Higher settings cause excessive clutch
cycling, premature tip wear and premature pump
wear.
CAUTION
Close the black fuel shutoff lever whenever you are
transporting the sprayer to prevent fuel from flooding
the engine.
Keep the sprayer upright and level when operating it
and when transporting it. This prevents crankcase oil
from leaking into the combustion chamber, which
makes startup very difficult.
g. Move the pressure control switch to OFF.
h. Relieve pressure by opening the pressure
drain valve.
10
i.
Close the pressure drain valve.
308568
CAUTION
Operating the sprayer with one pump not primed can
lead to premature packing wear and/or damage to
the unprimed pump.
Startup
2. Severe flow pulsations at the gun(s).
Loss of Prime to One Pump
Introduction of air into the pumps, either by changing
fluids or due to a suction leak, may result in the loss of
prime of one or both pumps. If both pumps lose their
prime, no fluid is pumped. Loss of prime to only one
pump is not as obvious, particularly if the sprayer is
operating at less than half capacity.
The following are indications of the sprayer operating
on one pump:
1. Continuous operation (no clutch cycling) at low
pressure, with less than the maximum tip sizes
(page 40). (Check that the pressure knob is turned
all the way UP, the engine is operating at maximum speed, and the filter screen is clean.
3. Clutch cycling is slower after changing fluids.
4. One pump will feel warmer than the other.
One pump cannot be primed while the other pump is
pumping under pressure.
To prime one or both pumps, relieve the pressure on
the system by opening the drain valve and following
the instruction on Prime the pumps, page 10.
Maintenance
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
DAILY:
sary.
Check the engine oil level and fill as neces-
DAILY:
Check and fill the gas tank.
AFTER THE FIRST 20 HOURS OF OPERATION
Drain the oil and refill with clean oil.
WEEKLY: Remove the cover of the air filter and
clean the element. Replace the element, if necessary.
If operating in an unusually dusty environment, check
the filter daily and replace it, if necessary.
Replacement elements may be purchased from your
local HONDA dealer.
CAUTION
For detailed engine maintenance and specifications,
refer to the separate engine manual, supplied.
WEEKLY: Check the level of the TSL in the displacement pump packing nut. Fill the nut, if necessary. Keep
TSL in the nut to help prevent fluid buildup on the
piston rod and premature wear of the packings.
AFTER EACH 100 HOURS OF OPERATION:
Change the oil. Refer to the engine manual for additional maintenance instructions.
SPARK PLUG: Use only an (NGK) BPR6ES or a
(NIPPON DENSO) W20EPR-U plug. Gap the plug to
0.028 to 0.031 inch (0.7 to 0.8 mm). Use a spark plug
wrench when installing and removing the plug.
308568
11
Pressure Relief Procedure
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D
D
D
D
are instructed to relieve the pressure,
stop spraying,
check or service any of the system equipment,
install or clean the spray tip.
1.
2.
3.
4.
Engage the gun safety latch.
Turn the engine switch to OFF.
Move the pressure control ON/OFF switch to OFF.
Disengage the gun safety latch. Hold a metal part
of the gun firmly to a grounded metal pail. Trigger
the gun to relieve pressure.
5. Engage the gun safety latch.
6. Open the pressure drain valve. Leave the pressure
drain valve open until you are ready to spray
again.
7. Disconnect the spark plug cable.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, VERY SLOWLY
loosen the tip guard retaining nut or hose end coupling
to Relieve the pressure gradually, then loosen completely. Now clear the tip or hose.
Flushing
5. Storage.
When to Flush
1. New Sprayer. This sprayer was factory tested in
lightweight oil,which was left in to protect the pump
parts.
Before using water–base paint, flush with mineral
spirits, followed by a soapy water flush, and then a
clean water flush.
Water base paint: flush with water, then mineral
spirits and leave the pumps, hose and gun filled
with mineral spirits. Shut off the sprayer, remove
the spark plug cable, and open the pressure drain
valve to Relieve the pressure. Leave the drain
valve open.
Before using oil–base paint, flush with mineral
spirits.
2. Changing Colors. Flush with a compatible solvent
such as mineral spirits or water.
3. Changing from water–base to oil–base paint. Flush
with warm, soapy water, then mineral spirits.
4. Changing from oil–base to water–base paint. Flush
with mineral spirits, followed by warm, soapy
water, and then a clean water flush.
CAUTION
To prevent pump corrosion or damage to pump
components, never leave water or any type of paint
in the sprayer when it is not in use. Pump the water
or the paint out with mineral spirits.
12
308568
Oil base paint: flush with mineral spirits and leave
the pump, hose and gun filled with mineral spirits.
Shut off the sprayer, remove the spark plug cable,
and open the pressure drain valve to Relieve the
pressure. Leave the drain valve open.
6. Startup after storage.
Before using water–base paint, flush out the
mineral spirits with soapy water, and then with
clean water.
When using oil–based paint, flush out the mineral
spirits with the paint to be sprayed.
Flushing
How to Flush
CAUTION
CAUTION
When changing fluids, do not drain all of the first fluid
from the suction tube before inserting the suction tube
into the another fluid. Not doing so may introduce
excessive air into the pumps and cause one or both
pumps to lose their prime.
After moving the suction tube to a new fluid, pump the
first fluid and any trapped air, out through the drain
valve before beginning to pump the new fluid to the
guns.
NOTE: The word solvent refers to water or oil-based
solvent.
1. Follow the Pressure Relief Procedure, page 12.
2. Remove the filter bowl (A) and screen (B); see
instruction manual 307273, supplied. Install the
bowl and support (C), without the screen, to flush.
Clean the screen separately. See Fig. 4.
Operation with one pump not primed can lead to
premature packing wear and damage to the pump.
NOTE: For multiple guns, unlock the gun trigger
safety on each gun and trigger that gun until clean
solvent comes from the nozzle. Flush each gun at
least one more time.
7. Check all fluid connections for leaks. Relieve the
pressure before tightening any connections. Start
the sprayer. Recheck the connections for leaks.
8. Remove the suction tube from the solvent pail.
Unlock the gun trigger safety. Trigger the gun to
force solvent from the hose. Do not let the pumps
run dry for more than 30 seconds, to avoid damaging the pump packings. Relieve the pressure.
9. Remove the strainer, suction tube and suction
hose and clean them separately to be sure all
paint sediment is removed. Dried paint can build
up in these parts and later cause performance
problems.
3. Close the pressure drain valve (53). See Fig. 4.
4. Put the suction tube in a grounded pail of solvent.
5. Remove the spray tip from the gun(s).
10. Unscrew the filter bowl and reinstall the clean
screen. Reinstall the bowl, hand tight only.
11. Follow Storage or Changing Colors, on page 12
Relieve the pressure.
WARNING
A
FIRE AND EXPLOSION HAZARD
To reduce static sparking and splashing,
always remove the spray tip from the
gun, and hold a metal part of the gun
firmly to the side of a grounded metal pail when
flushing.
6. Follow Startup on page 9. Keep the gun triggered until clean solvent comes from the nozzle.
Release the trigger and lock the gun trigger safety.
B
C
53
05062
Fig. 4
308568
13
Troubleshooting
WARNING
INJECTION HAZARD
To reduce the risk of serious injury, whenever you are instructed to relieve pressure, follow the
Pressure Relief Procedure on page 12.
Check everything in the chart before disassembling the sprayer.
PROBLEM
CAUSE
SOLUTION
The engine or sprayer won’t
start
start.
The engine switch is not on.
Turn on the switch.
The engine is out of gas.
Refill the gas tank. See page 8.
The engine oil level is low.
Try to start the engine. Replenish the oil, if necessary. See Step 4, page 6.
The spark plug cable is disconnected or it is
damaged
Reconnect the spark plug cable or replace the
spark plug.
There is frozen water in the pressure control.
Allow the sprayer to thaw completely before
starting it.
The engine won’t “pull over”.
Oil is seeping into the combustion chamber.
Remove the spark plug. Pull the starter rope 3
or 4 times. Clean or replace the plug. Try to
start the engine. Keep the sprayer upright to
avoid oil seepage.
The engine operates, but the
displacement pump does not
operate.
The pressure control switch is turned off.
Turn on the switch.
The pressure setting is too low.
Turn the pressure adjusting knob clockwise to
increase pressure.
The fluid filter (27) is dirty.
Clean the filter. See page 13.
The tip or the tip filter is clogged.
Clean the tip or the tip filter. See the gun
instruction manual.
The displacement–pump rod is stuck due to
dried paint.
Repair the pump. See page 32.
The connecting rod is worn or damaged.
Replace the connecting rod. See page 16.
The drive housing is worn or damaged.
Replace the drive housing. See page 18.
The electrical power is not energizing the field.
Check the wiring connections. See page 25.
With the pressure control switch turned on and
the pressure turned to maximum, use a test
light to check the power at the black and white
wires from the pressure control.
Have the pressure control checked by an authorized Graco dealer.
14
308568
The clutch is worn, damaged, or incorrectly
positioned.
Replace the clutch. See page 23.
The pinion assembly is worn or damaged.
Repair or replace the pinion assembly. See
page 20.
PROBLEM
CAUSE
SOLUTION
The pump output is low on
the upstroke.
upstroke
The inlet screen (102) is clogged.
Clean the screen.
A piston ball (425) is not seating.
Service the piston ball–check. See page 32.
The piston packings are worn or damaged.
Replace the packings. See page 32.
A o-ring (417) in the displacement pump is
worn or damaged.
Replace the o-ring. See page 32.
The inlet screen (102) is clogged.
Clean the screen.
The piston packings are worn or damaged.
Replace the packings. See page 32.
An intake valve ball is not seating
properly.
Clean the intake valve. See page 32.
The engine speed is too low.
Increase the throttle setting. See Step 12, page
10.
The clutch is worn or damaged.
Replace the clutch. See page 23.
The wetcup is loose.
Tighten the wetcup just enough to stop leakage.
The throat packings is worn or damaged.
Replace the packings. See page 32.
A displacement rod is worn or damaged.
Replace the rod. See page 32.
The inlet screen (102) is clogged.
Clean the screen.
The pressure setting is too low.
Increase the pressure. See Step 12, page 10.
The engine speed is too low.
Increase the throttle setting. See Step 12, page
10.
One pump is not primed.
See Loss of prime, page 11.
The fluid filter (27), the tip filter or the tip is
clogged or dirty.
Clean the filter. See page 13. Or, see the gun
instruction manual.
There is a large pressure drop in the hose.
Use a larger diameter hose.
Excessive pulsation
One pump is not primed.
See Loss of prime, page 11.
Fluid is spitting from the gun.
There is air in the pump or the hose.
Check and tighten all the fluid connections.
Reprime the pump. See page 10.
The tip is partially clogged.
Clear the tip. See the gun instruction manual.
The fluid supply is low or empty.
Refill the fluid supply. Prime the pump. See
page 9. Check the fluid supply often to prevent running the pump dry.
There is air in the pump or the hose.
Check and tighten all the fluid connections.
The output of one pump is
low on the downstroke or on
both of the strokes.
The paint leaks into the wetcup.
The fluid delivery is low.
The pumps are difficult to
prime.
Reduce the engine speed and cycle the
pumps as slowly as possible during priming.
The intake valve is leaking.
Clean the intake valve. Be sure ball seat is not
nicked or worn and that the ball seats well.
Reassemble the valve.
The pump packings are worn.
Replace the pump packings. See page 32.
The paint is too thick.
Thin the paint according to the supplier’s
recommendations.
The engine speed is too high.
Decrease the throttle setting before priming the
pump. See Step 8, page 10.
308568
15
Bearing Housing & Connecting Rod
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
11. Evenly lubricate the inside of the bronze bearing
(C) in the bearing housing (15), and the inside of
the connecting rod link (D), with high–quality motor
oil (do not use grease). Liberally pack the roller
bearing (E) in the connecting rod assembly (14)
with bearing grease.
12. Assemble the connecting rod (14) and bearing
housing (15).
NOTE: Steps 1 to 13 refer to Fig. 5 and Fig. 4.
1. Follow the Pressure Relief Procedure, page 12.
2. Remove the screws (55) and the front cover (13).
3. Remove the spring clip (54) and disconnect the
drain hose (104) at the pressure drain valve (53).
Unscrew the inlet manifold (98) from the pumps,
holding a wrench on the pump intake valve (B) to
keep the pump from loosening.
4. Disconnect the hose union (99) from the outlet
nipple (29).
5. Remove four screws (74) from the outlet manifold.
Do not remove the manifold halves from the displacement pump.
13. Clean the mating surfaces of the bearing and drive
housings.
14. Align the connecting rod with the crank (A) and
carefully align the locating pins (F) in the drive
housing (12) with the holes in the bearing housing
(15). Push the bearing housing onto the drive
housing or tap it into place with a plastic mallet.
CAUTION
Do not use the bearing housing screws (57) to align
or seat the bearing housing with the drive housing.
These parts must be aligned using the locating pins
(F), to avoid premature bearing wear.
6. Use a screwdriver to push up the retaining spring
(17) at the top of the pump. Push the pin (16) out
the rear.
15. Install the screws (57) and lockwashers (58) on the
bearing housing. Tighten evenly to 300 in-lbs (34
N@m).
7. Loosen the jam nuts (18) with an adjustable
wrench. Rotate pump 1/4 turn to allow clearance
for the second pump to turn. Unscrew and remove
the displacement pump.
16. Refer to Installing the Pump on page 33.
8. Use a hex key wrench to remove the four screws
(57) and lockwashers (58) from the bearing housing (15).
9. While pulling the connecting rod (14) with one
hand, lightly tap the lower rear of the bearing
housing (15) with a plastic mallet to loosen it from
the drive housing (12). Pull the bearing housing
and the connecting rod assembly (14) off the drive
housing.
10. Inspect the crank (A) for excessive wear and
replace parts as needed.
16
308568
17. Install the front cover.
WARNING
MOVING PARTS HAZARD
Be sure the retaining spring (17) is firmly
in the groove, all the way around, to
prevent the pin (16) from working loose
due to vibration.
If the pin works loose, it or other parts could break
off due the force of the pump action. These parts
could be projected through the air and result in
serious injury or property damage, including damage to the pump and bearing housing.
14
58
1
D
12
E
A
C
57
13
104
F
16
54
72
2
73
99
2
15
17
33
71 29
18
90
55
1
Torque the screw to 300 in-lb (34 N@m).
70
74
19
98
B
Nipple (72) and sealnut (73) shown separated for
reference only. Do not disconnect from manifold
halves (71) and (70) or pump cylinders (19).
Fig. 5
2
05063
308568
17
Drive Housing
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
NOTE: Refer to Fig. 6 for this procedure.
1. Follow the Pressure Relief Procedure, page 12.
2. Remove the pumps and bearing housings. Follow
Steps 1 to 9 on page 16.
3. Remove two screws (26) holding the drive housing
(12) to the cart frame (35).
4. Remove the three screws (20) and lockwashers
(9) from the drive housing (12).
5. Remove the five screws (10) and lockwashers (9)
from the pinion housing (11).
CAUTION
The sprayer may become out of balance with the
drive housing removed. Support the rear of the cart
to prevent the partially disassembled sprayer from
falling over.
6. Lightly tap around the drive housing (12) to loosen
the drive housing. Pull the drive housing straight
off the pinion housing. Be prepared to support the
gear clusters (24, 89), which may also come out.
18
308568
CAUTION
Do not drop the gear clusters (24, 89) when removing
the drive housing (12). The gear cluster is easily
damaged. The gear may remain in either the drive
housing or pinion housing.
Do not lose thrust balls (12c or 11d) located at each
end of the gear cluster, or allow them to fall between
the gears. The ball, which is heavily covered with
grease, usually stays in the housing recesses, but
could be dislodged. If the balls are caught between
the gears and not removed, they will seriously damage the drive housing. If the balls are not in place,
the bearings wear prematurely.
CAUTION
Drive housing must be set up and aligned properly or
there will be premature bearing wear and loss of
sprayer performance.
7. Place one bronze-colored washer (12a) and then
one silver-colored washer (12b) on each shaft
protruding from each big gear of the drive housing
(12).
8. If replacing the complete drive housing assembly
(12), brush G-n lubricant (supplied) on all gear
teeth. Then recoat the gear teeth with bearing
grease (supplied). Pack the remaining bearing
grease into the bottom part of the drive housing.
Use all of the bearing grease. See Fig. 7.
9. Install new gasket (109) (supplied).
10. Hold the crankshafts (A) between the TL timing
lines on the drive housing while assembling the
drive housing (12) to the pinion housing (11) until
the gears are engaged. See Fig. 8.
11. From Step 5, work backwards to reassemble or,
move ahead to the next section in this manual if
further service is needed.
Drive Housing
12a
12b 89
1
9
11
10
109
12
11d
15
58
9
57
12c
24
1
20
13
55
35
26
1
Note position of gear offset when assembling gears
05064
Fig. 6
1
A
A
2
Fig. 7
1
Coat with G-n lubricant
2
Pack with bearing grease
05089
05088
Fig. 8
308568
19
Pinion, Clutch, Clamp, Field, & Engine
Replacement of the pinion shaft (11f**), bearing
(11g**), or splined hub (11h**) ( Fig. 13, page 22)
requires removal of the pinion housing (11). Follow
steps 1 through 4 below.
If servicing clutch components only, see page 23.
CAUTION
The sprayer will become out of balance with the drive
housing and pinion housing removed. Support the
rear of the cart to prevent the partially disassembled
sprayer from falling over.
CAUTION
Pinion Housing Removal
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
Do not lose the thrust balls (11d). Refer to the CAUTION on page 18 for more information.
NOTE: To disassemble the pinion, go to page 21. To
disassemble more of the sprayer, go to page 23. To
reassemble the sprayer from this point, skip ahead to
Reassembly, page 29, Step 9.
NOTE: Refer to Fig. 9 for Steps 1 to 5.
1. Follow the Pressure Relief Procedure, page 12.
2. If the drive housing has not yet been removed,
follow steps 1 through 6 of DRIVE HOUSING, on
page 18.
3. Remove the two bottom screws (10) and lockwashers (9) first, then remove the two side screws
(10) and lockwashers (9), and last remove the top
screw (10) and lockwasher (9).
1
See page 21.
2
Brush with G-n lubricant.
3
Pack with bearing grease.
9
10
2
4. Pull the pinion housing (11) away from the clutch
housing (2). The armature (4b) will come with it.
5. Pull the armature (4b) off the hub (11h**) of the
pinion housing. Also see Fig. 13.
11
4b
6. If replacing the complete pinion housing assembly
(11), brush G-n lubricant (supplied) on the pinion
shaft teeth. Then recoat the pinion shaft teeth with
bearing grease (supplied). Pack the remaining
bearing grease in the bottom part of the pinion
housing. Use all of the bearing grease.
7. Install new gasket (109) (supplied).
11d
8. Reassemble to drive housing. See step 10 on
page 18 for the timing procedure.
Fig. 9
20
308568
1
2
3
05065
Pinion Housing
Repairing the Pinion Shaft Assembly
Hydraulic Press
NOTE: Refer to Fig. 13 except where noted.
Pinion Assembly
NOTE: A hydraulic press is required for disassembly
and reassembly of the pinion shaft assembly. A Repair
Kit 237847 is available which includes the shaft and
bearings, pre-assembled and lubricated.
If using Repair Kit 237847, follow Steps 1 to 7, below.
1. Remove the small ring (11j**) from the hub (11h**)
and the large ring (11k) from the bearing recess of
the pinion housing (11a).
2. Using a hydraulic press, push on the front of the
shaft (11f**) to force the pinion shaft assembly out
of the housing (11a). See Fig. 11.
05067
Steel Blocks
Fig. 11
Hydraulic Press
Steel Plate
Steel Tube
2–3/8 OD
x 2–1/8 ID
3. Press the new pinion shaft assembly into the
pinion housing, pushing it to the shoulder of the
housing (11a). See Fig. 12. Use a steel tube to
press on the outside diameter of the bearing to
prevent damage to the bearing.
4. Install the rings (11k and 11j**). Be sure to install
11k with the bevel facing the back of the housing.
See Fig. 13.
Fig. 12
5. Install new gasket (109).
If purchasing parts separately, use these instructions.
Disassemble as far as needed for the parts being
replaced.
6. Reassemble to drive housing (12). See step 10 on
page 18 for the timing procedure.
7. Go to Reassembly, page 29, Step 9, or continue
on page 23.
Steel Blocks
05068
NOTE: The old bearing (11g**) will be damaged when
the pinion shaft assembly is removed. Have an extra
bearing on hand if you need to remove it for any
reason.
1. Remove the small ring (11j**) from the hub (11h**).
A
A
B
C
D
Fig. 10
2. Remove the snap ring (11k) from the bearing
recess of the pinion housing (11a).
B
Hydraulic press
Use a 5/8 in. round steel bar
to push on the shaft (11f**)
Position two steel bars as
shown.
Platform of hydraulic press
11h**
11g**
C
D
05066
3. Using a hydraulic press, support the housing on
blocks. Push on the front of the shaft (11f**) to
force the pinion shaft assembly out of the housing.
See Fig. 11.
4. Using a hydraulic press, place pieces of steel
bar stock on the inner race of the bearing (11g**)
and press the shaft through the hub and bearing.
See Fig. 10.
308568
21
Pinion Housing
5. Apply lubricant to the parts as shown in Fig. 13.
8. Install the rings (11k and 11j**). Be sure to install
ring 11k with the bevel facing the back of pinion
housing (11a). Install the small ring (11j**). See
Fig. 13.
6. Using a hydraulic press, press fit the following
parts: Bearing (11g**) to the shaft shoulder , using
a steel ring that contacts the inner race only. Hub
(11h**) onto shaft (11f**) to contact the inner ring
of bearing (11g**).
9. Perform steps 5 and 6 on page 21 of If using
Repair Kit 237847.
7. Using a hydraulic press, Install the pinion shaft
assembly, by pressing it to the shoulder of the
housing (11a). Use a steel tube to press on the
bearing outer race to prevent damage to the
bearing. See Fig. 12.
10. Go to Reassembly, page 29, Step 9, or continue
on page 23.
5
1
6
11a
2
11k
1
The back of the pinion housing (11a).
2
Press the pinion shaft assembly in here.
3
Lubricate the inner and outer diameters.
4
Lubricate the teeth.
5
Cutaway view of the pinion housing (11a).
6
Bevel faces back of pinion housing (11a).
7
Gasket
**
Included in Repair Kit 237847.
11j**
11h**
11g**
11f**
11d
3
4
7
05069
Fig. 13
22
308568
Clutch
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
NOTE: The clutch assembly (4) includes the armature
(4b) and rotor (4a). The armature and rotor must be
replaced together so they wear evenly.
NOTE: If the pinion assembly (11) is not yet separated
from the clutch housing (2), follow Steps 1 to 4. Otherwise, start at Step 5.
5. Tap lightly on the back of the bearing housing (15)
with a plastic mallet to loosen the assembly (D)
from the clutch housing. Pull the assembly away.
6. The armature (4b) was removed with the pinion
housing. Remove the armature from the pinion
hub.
CAUTION
Examine the splined hub (11h**, Fig. 13, page 22) for
wear. Replace as needed. Follow the Pinion Housing
instructions, page 21.
NOTE: Refer to Fig. 14 for this procedure.
1. Follow the Pressure Relief Procedure, page 12.
2. Disconnect the hose union (99) from the outlet
nipple (29). Disconnect the drain hose (104) at the
pressure drain valve (53). Also see Fig. 5 and Fig.
4.
3. Remove the two bottom screws (26) holding the
drive housing to the cart frame (35).
4. Remove the two bottom screws (10) and lockwashers (9) first, then remove the two side screws
(10) and lockwashers (9), and last remove the top
screw (10) and lockwasher (9).
CAUTION
The sprayer may become out of balance with the
drive housing and pinion housing removed. Support
the rear of the cart to prevent the partially disassembled sprayer from falling over.
7. There are two ways to remove the rotor (4a).
a. Remove the four socket head capscrews (22)
and lockwashers (21). Install two of the screws
in the threaded holes (E) in the rotor. Alternately tighten the screws until the rotor comes
off. See Fig. 14.
b. You can use a standard steering wheel puller
(A). However, two 1/4–28 x 3 or 4 in. long
screws (B) are also needed. Replace the short
screws of the steering wheel puller with the
longer screws (B). Turn the screws (B) into the
threaded holes (E) of the rotor (4b). Tighten
the capscrew (C) of the tool until the rotor
comes off. See the Detail in Fig. 14.
8. Skip ahead to Reassembly, page 29, Step 7, or
continue on page 25.
308568
23
Clutch
10
9
2
4a
21
E
22
D
4b
35
11
26
33
99
15
A
B
C
05071
05070
Fig. 14
24
308568
Engine
NOTE: The engine must be removed before the Field,
Clamp and Clutch Housing can be removed.
CAUTION
The sprayer will be out of balance when the engine,
clutch housing, drive housing and pinion housing are
removed. Support the rear of the cart to prevent the
partially disassembled sprayer from falling over.
1. Working under the mounting plate (A), remove the
two lock nuts (51) and then pull the screws (50)
out of the base of the engine. Disconnect the red
wire (B) from the engine lead (D). Disconnect the
black and white wires from the field. Pull the wires
(63) and (D) carefully through the grommets (66)
before removing the engine. See Fig. 15 and 16.
2
D
2. Lift the engine carefully and place it on a work
bench.
3. Remove the Field and Wiring Harness, Clamp
and Clutch Housing, as instructed on pages 26
and 26.
50
NOTE: All service to the engine must be performed by
an authorized HONDA dealer.
51
1
66
A
05073A
Fig. 16
To engine alternator.
66
65
WHITE
BLACK
63
B
RED
D
1
66
Fig. 15
Bottom View of Engine and Cart
05072
308568
25
Field & Wiring Harness
NOTE: Refer to Fig. 17.
1. Remove the engine from the cart. See page 25.
2. Pull the plastic caps (B) off the wire screws (62) in
both places on the field. Remove the screws and
remove the wire (63).
2
6
3. Back out the four setscrews (25) holding the field
(6) to the clutch housing (2) approximately 5 turns.
4. Pull out the field. The field fits closely to the clutch
housing and must be removed carefully to prevent
jamming.
63
62
5. Skip ahead to Reassembly, page 27, Step 5 or
continue on page 26.
25
B
05074
Fig. 17
Clamp
NOTE: A standard steering wheel puller and two
1/4–28 x 3 or 4 in. long screws are required to remove
the clamp.
2
A
B
C
NOTE: Refer to Fig. 18.
1. Loosen the two screws (22) on the clamp (3),
working through the slot at the bottom of the clutch
housing (2).
2. Install two screws (B) of the tool (A) in two of the
threaded holes in the clamp (3). Tighten the screw
(C) until the clamp comes off.
3
22
05075
Fig. 18
3. Skip ahead to Reassembly, page 27, Step 3, or
continue below.
Clutch Housing
NOTE: Refer to Fig. 19.
23
1. Remove the four capscrews (8) and lockwashers
(9) which hold the clutch housing (2) to the engine.
94
2
2. Remove the engine key (23).
9
8
3. Pull off the clutch housing (2).
4. Skip ahead to Reassembly, page 27, Step 1.
26
308568
Fig. 19
05076
Reassembly
To check the dimension, place a rigid, straight
steel bar (B) across the face of the clutch housing
(2). Use an accurate measuring device to measure
the distance between the bar and the face of the
clamp. Adjust the clamp as necessary. Torque the
two screws (22) to 120 in–lb (14 N.m).
CAUTION
The sprayer will be out of balance when only the
engine and clutch housing are installed. Support the
rear of the cart to prevent the sprayer from falling
over.
5. Connect the wires of the harness (63) with the
screws (62) in both places on the field (wires can
be attached to either connection). Pull the plastic
caps (C) up and snap them over the screws. Install
the field in the clutch housing. Push the wire
harness through the slot in the clutch housing.
Align the setscrew holes in the field and the clutch
housing (2). Use a feeler gage to center the field
(6) by measuring the gap between the four housing bosses where the set screws pass through the
housing and the field. Adjust the set screws to
provide even clearance. Then tighten the setscrews (25) oppositely and evenly, to 27 in–lb (3.2
N.m). See Fig. 20.
1. Install spacer (94) between the engine and the
clutch housing (2).
2. Install the clutch housing (2), capscrews (8) and
lockwashers (9) on the engine.
3. Install the engine shaft key (23). See Fig. 20.
4. Press the clamp (3) onto the engine shaft (A).
Maintain the 1.084 inch +/– 0.01 (27.53 +/– 0.25
mm) dimension shown in Fig. 21.
1
Torque the screws oppositely and
evenly to 27 in–lb (3.2 N@m).
2
Slot.
3
Torque the screws to 200 in–lb (22 N@m).
4
Apply low strength thread locker to set
screws (25).
23
94
4
1
25
9
3
8
3
A
2
2
22
6
C
Fig. 20
63
62
05077
308568
27
Reassembly
1
The face of the housing.
2
1.084 ".010 inch (27.53 ".25 mm).
3
CAUTION
The sprayer will be out of balance when only the
engine and clutch housing are installed. Support the
rear of the cart to prevent the sprayer from falling
over.
Torque the screws to
120 in–lb (14 N.m).
1
2
2
B
22
Fig. 21
28
308568
3
05078
6. Place the engine (1) assembly on the cart. Align
the mounting holes. Carefully guide the engine
wire (D) and wiring harness (63) from the field,
through the appropriate grommets (66) in the
mounting plate (E). Install the flange screws (50)
and locknuts (51), but do not tighten these screws
yet. Connect the engine wire (D) to the red wire
(B), and connect the black and white wires as
shown in the Detail drawing in Fig. 22.
Reassembly
7. Be sure the face of the rotor (4a) and the field (6)
are free of all oil and contaminants. Remove any
burrs on the outside edge of the rotor. Install the
rotor, lockwashers (21) and capscrews (22).
Torque the capscrews to 7 ft–lb (9.5 N.m). See
Fig. 22.
9. Be sure the face of the armature (4b) is clean.
Assemble the armature to the hub in the pinion
housing (11). A retaining ring located within the
armature makes it difficult to assemble these
parts. Follow this procedure for the best results.
First, lock a few splines of both parts. While they
are locked, use a screwdriver to gently push the
retaining ring into the armature, and finish engaging the splines. Push the armature onto the hub
until it contacts the ring (11j**). See Fig. 13 on
page 22.
8. After installing the rotor (4a), pull the engine recoil
rope to assure that the engine turns freely, and
there is no contact between the rotor (4a) and the
field (6). If there is contact, loosen the setscrews
(25) and reposition the field. Tighten the setscrews
oppositely and evenly to 27 in–lb (3.2 N@m).
10. Assemble the drive assembly (D) to the clutch
housing, using the capscrews (10) and lockwashers (9). See Fig. 22.
11. Install the flange screws (26), then tighten lock
nuts (51) and screws (26).
66
1
BLACK
65
B
63
RED
D
66
25
WHITE
9
10
3
05072
2
1
D
1
Torque the screw to 7 ft–lb (9.5 N.m).
2
The face must be clean.
3
To engine alternator.
4
Spline
4
2
4a
2
22 21
4b
50
E
11
6
26
51
05079A
Fig. 22
308568
29
Pressure Control Replacement
WARNING
59
1
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
A
301
96
1. Follow the Pressure Relief Procedure, page 12.
2. Use two wrenches and disconnect the hose at the
pressure control. Hold the fitting (A) firmly. See the
CAUTION, below. See Fig. 23.
3. Disconnect drain hose (104) at the pressure drain
valve (53). Remove screw (100) and use two
wrenches to disconnect the fitting between the
filter and the pressure control. Hold the fitting (A)
firmly. Remove the filter with the bracket (96).
Loosen the two screws (30) holding the filter to the
bracket (96), but do not remove them.
A
1
104
To the pump.
100
Fig. 23
30
53
05080
310
317
C
B
314
301
304
302
CAUTION
Do not allow the fitting (A) to turn when removing or
connecting the hose or filter. Turning the fittings can
shift the calibration of the pressure control.
4. Remove the four mounting screws and washers
(302, 303, 304) from the pressure control cover
(76). See Fig. 24.
5. Carefully remove the engine control board (301) so
as not to stress the cables.
6. Disconnect the black and white wires of the pressure control cable (314) from the engine control
board.
7. Disconnect the potentiometer cable assembly
(310) from the pressure control cover.
8. Disconnect the red power lead (B) from the ON/
OFF switch.
9. Loosen the ground terminal screw (317) and
disconnect the ground lead (C).
30
308568
304
303
05081
Fig. 24
WARNING
Do not attempt to adjust or calibrate the pressure
control. If the pressure control is faulty, replace it.
10. Pull off the engine control board.
11. Reassemble in the reverse order; attach ground
wire (C), power lead (B), and the black and white
connectors. Attach the engine control board (301)
using the four mounting screws and washers (302,
303, 304).
12. Use two wrenches and tighten the filter and hose
fittings (A). See preceding caution.
13. Slide bracket (96) to contact cart squarely. Tighten
both filter mounting screws (30). Install and tighten
screw (100).
14. If replacing the complete pressure control, follow
steps 1 through 3 on page 30 and remove three
mounting screws (64) and lock washers (92).
Remove pressure control (59). See Fig. 25.
15. Reassemble screws (64) and lock washers (92),
then follow steps 12 and 13 on page 30.
59
64
92
97
96
Fig. 25
05096
308568
31
Displacement Pump
WARNING
INJECTION HAZARD
To reduce the risk of serious injury,
whenever you are instructed to relieve
pressure, follow the Pressure Relief
Procedure on page 12.
Removing the pump. (See Fig. 26.)
1. Follow the Pressure Relief Procedure, page 12.
2. Flush the pump. See page 13.
15
17
18
2
16
3. Remove the spring clip (54) and disconnect the
drain hose (104) at the pressure drain valve (53).
Unscrew the inlet manifold (98) from the pumps,
holding a wrench on the pump intake valve (B) to
keep the pump from loosening.
72
73
54
32
308568
71
33
19
90
70
74
5. Remove four screws (74) from the outlet manifold.
Do not remove the manifold halves from the displacement pump.
7. Loosen the jam nuts (18) with an adjustable
wrench. Rotate pump 1/4 turn to allow clearance
for the second pump to turn. Unscrew and remove
the displacement pump.
29
104
4. Disconnect the hose union (99) from the outlet
nipple (29).
6. Use a screwdriver to push up the retaining spring
(17) at the top of the pump. Push the pin (16) out
the rear.
99
2
1
B
98
1
Torque the screw to 70 in–lb (8 N@m).
2
Nipple (72) and sealnut (73) shown separated for
reference only. Do not disconnect from manifold
halves (71) and (70) or pump cylinders (19).
Fig. 26
Repairing the pump
See manual 307806 for pump repair instructions.
05082
Displacement Pump
Installing the pump. (See Fig. 27.)
1. Install the lock nut (18) all the way on the pump.
Screw one pump about 3/4 of the way into the
bearing housing (15). Hold pin (16) up to pin hole
in connecting rod (14) and continue to screw in the
pump until pin slides easily into hole. Continue
screwing in pump until it stops on the lock nut (18).
Repeat the procedure for the second pump.
CAUTION
Do not rotate outlet manifold half (70, 71) on nipple
(72). Rotation may cause leakage at seal nut (73).
2. Back off each pump until the top of the pump
cylinder is flush with bearing housing face as
indicated. Orient outlet manifolds so the tops are
aligned by rotating cylinders no more than one turn
up or down.
4. If manifolds were not moved during service, holes
will be aligned. If holes are not aligned or a new
pump is being installed, align outlet manifolds (70
and 71) horizontally by screwing in or out on the
outlet nipple (72) installed in the cylinder (19).
Keep manifolds evenly engaged on nipples (72).
Install o-ring (90) between manifold halves (70)and
(71). Install and tighten four screws (74) to 70 in-lb
(8 N@m). Tighten both seal nuts (73) to manifold
face. See Fig. 26.
5. Tighten lock nut (18) to 79 ft-lb (107 N.m) with a
wrench and hammer.
6. Install inlet manifold (98) and siphon assembly.
1
Pump cylinder flush with this face
2
Torque the nut to 79 ft–lb (107 N@m).
16
WARNING
MOVING PARTS HAZARD
Be sure the retaining spring (17) is firmly
in the groove, all the way around, to
prevent the pin (16) from working loose
due to vibration.
If the pin works loose, it or other parts could break
off due the force of the pump action. These parts
could be projected through the air and result in
serious injury or property damage, including damage to the pump and bearing housing.
3. Push the retaining spring (17) into the groove all
the way around the connecting rod.
14
17
15
1
18
2
05083
Fig. 27
308568
33
Sprayer Parts Drawing
Model 231343
DETAIL
Ref 36
3
40
45
37
38
39
3
113
54
112
A
114
B
79
1
1
33
67
128
99
32
68
101
91
127
95
94
36
23
2
25
9
10
50
2
48
9
3
47
8
7
4a
26
22
118
21
21
51
22
102
6
A
63
62
4b
105
52
32
104
1
Label
2
See the detail, above.
3
See page 36 for the parts.
34
308568
69
46
35
41
44 42 43
5084B
Sprayer Parts List
Ref
No.
Part No.
Description
1
2
3
4
112773
237856
190092
237839
4a
4b
6
7
8
183400
108800
112815
9
10
104008
101864
21
22
105510
108803
23
25
26
190093
108801
111192
32
33
112799
237837
ENGINE, gasoline, 8 hp
1
CLUTCH HOUSING
1
CLAMP, rotor
1
CLUTCH ASSEMBLY
1
includes 4a and 4b
@ROTOR, 5” clutch
1
@ARMATURE, 5” clutch
1
FIELD, 5” clutch
1
PIN, dowel, spring, 5/16 x 1 inch
1
CAPSCREW, socket head, 5/16–24
4
x 2–1/2 inch
WASHER, lock, spring
17
CAPSCREW, socket head, 5/16 x 18 10
x 1 inch
WASHER, lock, spring
6
CAPSCREW, socket head,
6
1/4–28 x 1 inch
KEY, parallel, 1/4 inch sq x 1.72 inch 1
SETSCREW, 1/4–20 x 5/16 inch
4
FLANGE SCREW, hex head, 3/8–16 2
x 7/8 inch
CLAMP, hose
2
HOSE, 1/2 inch ID, cpld 3/8–18 npt
1
42 inch (1067 mm),
spring guard both ends
CART FRAME
1
CART HANDLE & HOSE RACK
1
WASHER, plain
2
PIN, spring, straight,
2
3/
16 x 1–1/4 inch
SCREW, mach, pan head,
4
10–32 x 5/16 inch
SLEEVE
2
WHEEL, semi-pneumatic
2
RING, retaining
2
HUBCAP
2
35
36
37
38
237473
238187
183350
108068
39
108795
40
41
42
43
187604
112786
101242
104811
Qty
Ref
No.
Part No.
Description
44
45
46
47
48
154636
112827
112125
237686
112798
50
112785
51
52
54
62
63
67
68
69
79Y
91
94
95
99
101
101566
186494
186490
108860
220980
190775
112826
190776
181867
111178
190443
113082
237834
237843
102
104
105
112
113
114
118
127
128
237840
190781
103546
113084
290137
190684
100023
194498
102478
WASHER, 5/8 inch
BUTTON, snap
PLUG, tubing
GROUNDING CLAMP & WIRE
SCREW, hex washer head,
8–32 x 3/8 inch
FLANGE SCREW, hex head,
3/8–16 x 1–1/2 inch
LOCKNUT, heavy hex, 3/8–16
CLIP, spring, 1.62 in. diameter
CLIP, spring, 2.00 in. diameter
SCREW, mach, bdgh, 8–32 x 1/4 inch
HARNESS, wiring
HOSE, suction
RING, retaining
TUBE, suction
LABEL, warning
PACKING, o-ring
SPACER, thermal
PACKING, o-ring
UNION, swivel
CONNECTOR, barb, hose
includes 91 and 95
STRAINER
TUBE, drain
TIE, cable
RIVET
LABEL, throttle
HOLDER, throttle label
WASHER, flat
TAG, throttle
TIE, wire
Qty
2
2
2
1
1
2
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
3
2
1
1
2
1
1
Y Replacement Danger and Warning labels, tags, and
cards are available free.
308568
35
Sprayer Parts Drawing
Model 231343
60,61
28
B
1
100
27
31
59 4
92
29
29
66
64
64
64
34
92
29
30
11
10
9
65
97
66
96
53
2
Ref 11d
103
120
12b
12a
A
1
104
89
81
12
24
12c
14
58
13
57
56
9
1
109
20
15
17
55
73
71
29
70
18
16
90
72
19
3
74
1
Label
2
See page 38 for the parts.
3
See manual 307806 for the parts.
4
See page 39 for the parts.
98
05085
36
308568
Sprayer Parts List
Ref
No.
Part No.
Description
9
10
104008
101864
11
237846
12
237845
12a
12b
12c
12d
12e
12f
13
14
15
16
17
18
19
106227
183209
100069
113089
113085
190662
189950
220640
220639
183210
183169
189969
220872
20
111822
24
27
237844
237481
28
29
100040
162485
30
110997
31
34
53
155699
237479
237677
WASHER, lock, spring
17
CAPSCREW, socket head, 5/16 x 18 10
x 1 inch
PINION HOUSING ASSEMBLY
1
See parts on page 38
DRIVE HOUSING
1
Includes items 12a to 12f
@WASHER, bronze
2
@WASHER, silver
2
@BALL, sst
2
@JAR, grease
1
@TUBE, grease
1
@GASKET, housing
1
COVER, Front
1
ROD, connecting
2
HOUSING, bearing
2
PIN, straight, 3/8 x 1–1/8 inch
2
SPRING, retaining
2
NUT, hex, 1–13/16 –16
2
DISPLACEMENT PUMP
2
See manual 307806 for parts
CAPSCREW, socket head, 5/16 x 18 3
x 3”
GEAR REDUCER
1
FILTER, fluid
1
See manual 307273 for parts
PLUG, pipe, sq head, 3/8 npt
1
4
NIPPLE, pipe, 3/8 npt(m) x
3/ npsm(m)
8
FLANGE SCREW, hex
2
head, 1/4–20 x 5/8 inch
ELBOW, street, 3/8–18 npt (m x f)
1
CAP, filter
1
PRESSURE DRAIN VALVE
1
Qty
Ref
No.
Part No.
Description
55
56
57
108850
290373
110141
58
59
106115
237838
60
61
64
65
66
70
71
72
73
74
290375
290374
101344
108868
109099
190103
190104
190105
112778
112783
81Y
89
90
92
96
97
98
100
103
104
109
120
185953
237849
107305
100214
237831
190474
237827
112818
110838
190664
190662
113983
SCREW, filh, 10–24 x 2 inch
LABEL, identification
CAPSCREW, hex head,
3/ –16 x 1–1/2 inch
8
LOCKWASHER, spring, 3/8 inch
CONTROL, pressure
See parts on page 39
LABEL, identification, control, top
LABEL, identification, control, bottom
FLANGE SCREW, hex, 5/16–18
CLAMP, wire
BUSHING, snap
MANIFOLD, pump
MANIFOLD, pump
NIPPLE, adapter
NUT, seal
FLANGE SCREW, hex head,
1/4–20 x 1 inch
LABEL, Danger, English
GEAR REDUCER
PACKING, o-ring
LOCKWASHER, 5/16
BRACKET, filter mounting
BRACKET, control
MANIFOLD, inlet
SCREW, cap, hex head, lg flange
LOCKNUT, 5/16–18
TUBE, drain
GASKET, housing
RING, retaining
Qty
4
1
8
8
1
1
1
6
1
3
1
1
2
2
4
1
1
1
5
1
1
1
1
1
1
1
1
Y Replacement Danger and Warning labels, tags, and
cards are available free.
308568
37
Pinion Assembly Parts List and Drawing
Assembly 237846
Ref
No.
Part No.
Description
11a
11b
11c
11d
11e
11f**
189948
112602
108692
100069
107088
190077
.PINION HOUSING
.PIN
.BEARING
.BALL
.BEARING
.PINION SHAFT
11a
Ref
No.
Qty
1
2
2
2
1
1
11b
Part No.
Description
Qty
11g** 108798
.BALL BEARING, large
11h** 190665
.HUB, armature
11j**
108796
.RETAINING RING, small
11k
112770
.RETAINING RING, large
11l
190662
.GASKET, housing
**Included in Repair Kit No. 237847.
1
1
1
1
1
11k
11c
11e
11j**
11h**
11g**
11l
11f**
05069
11d
Accessories
Displacement Pump Repair Kit
220877
Parts included in the kit are shown in manual 307806.
Sleeve Removal Tool
224788
Required for removing the displacement pump sleeve.
Hose, 3/8” x 50’
237854
3/8–18 npt male x 3/8–18 npsm female swivel.
Hose, 3/8” x 50’
3/8–18 npsm female swivel, both ends.
238041
Suction Tube Kit
For use with 55 gallon (200 liter) barrels.
238046
Dual Filter Kit
238045
Required for multiple gun spraying operations.
Immersion Tube Kit
To be used with a 5–gallon bucket.
238044
Contractor Spray Gun
220955
Gun Manifold
Connects three guns to fluid filter.
238042
38
308568
Contractor Spray Gun/3/8” Hose Kit
238000
RACt IV Driplesst Tip Guard
220422
Safety feature that reduces the risk of injection injury.
RACt IV Heavy Duty Tip Guard
222674
Safety feature that reduces the risk of injection injury.
DANGER LABELS
The English language DANGER label shown on
page 4 is also on your sprayer. If you have painters
who do not read English, order one of the following
labels to apply to your sprayer. The drawing below
shows the best placement of these labels for good
visibility.
Order the labels from your Graco distributor.
Apply other
language here
French
Spanish
German
Greek
Korean
English
185956
185961
186041
186045
186049
185593
05086
Pressure Control Parts List
237838 Pressure Control for the GM10000 Sprayers
Ref
No.
Part No.
Description
301
302
303
304
305
306
307
308
309
310
237673
107251
112610
100020
189095
112614
105679
107255
105659
236352
311
112382
ENGINE CONTROL BOARD
SCREW, panhead, 10–24 x 1 inch
SCREW, panhead, 10–24 x 2 inch
LOCKWASHER, No. 10
HOUSING,
PLUG
TOGGLE SWITCH
GUARD
BOOT
POTENTIOMETER, pressure
adjustment
NUT, shaft, sealing
Qty
1
2
2
4
1
1
1
1
1
1
Ref
No.
Part No.
Description
312
313
314
315
316
317
318Y
319Y
112373
185565
237674
109078
112376
100078
189286
189246
KNOB
LABEL
CONDUCTOR
CONNECTOR
LOCKNUT
SCREW, hex head, 8–24 x .375 inch
LABEL, warning
LABEL, warning
Qty
1
1
1
1
1
1
1
1
Y Replacement Danger and Warning labels, tags, and
cards are available free.
1
Parts Drawing –
Pressure Control
Wiring Schematic –
Pressure Control
309
310
313
308
Y319
307
301
312
311
305
307
317
310
Y318
304
WHITE
314
302
316
RED
314
1
2
GREEN
306
301
315
303
304
GROUND
1
To engine
2
To clutch field
2
BLACK
03496
05087A
Dimensions
Graco Phone Number
Weight (dry, without packaging) . . . . . . . . . . . . 220 lb (100 kg)
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 inch (813 mm)
Length (with suction hose installed) . . . . . . 36 inch (915 mm)
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 inch (585 mm)
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest
to you: 1–800–690–2894 Toll Free
308568
39
Technical Data
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 horsepower, Honda
Maximum working pressure . . . . 3000 psi (207 bar, 21 MPa)
Noise Level
Sound power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 dB(A)
Per ISO 3744
Sound pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB(A)
measured at 3.1 feet (1 m)
Cycles/gallon (liter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 (13)
Maximum delivery . . . . . . . . . . . . . . . . . . . 2.5 gpm (9 liter/min)
Fuel tank capacity . . . . . . . . . . . . . . . . 1.59 gallons (6.04 liter)
Maximum tip size . . . . . . . . . . . . . . . 1 gun with 0. 055 inch tip
up to 6 guns with 0.021 inch tip
Inlet paint strainer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 mesh
stainless steel screen, reusable
Outlet paint filter . . . . . . . . . . . . . . . . . . . 60 mesh (250 micron)
stainless steel screen, reusable
Pump inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . 3/4 inch npt (m)
Fluid outlet size . . . . . . . . . . . . . . . . . 3/8 npsm from fluid filter
Wetted parts
Displacement Pump . . . . . . . stainless steel, carbon steel,
polyurethane, uhmw polyethylene,
Delrinr, leather
Filter . . . . . . . . . . . aluminum, carbon steel, stainless steel
Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum
Suction Hose . . . . . . . . . . . . . . . . . Nitrile (synthetic rubber)
NOTE: Delrinr
Graco Warranty
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the “Graco Contractor Equipment Warranty
Program”.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Sales Offices: Minneapolis, Detroit
Foreign Offices: Belgium, Korea, Hong Kong, Japan
GRACO INC.
P.O. BOX 1441
MINNEAPOLIS, MN
http://www.graco.com
40
308568
PRINTED IN USA 308568 May 1995, Revised October 1999
55440–1441