HOT WATER BOTTLE BATH
PART NUMBER 00-64002
INSTALLATION INSTRUCTIONS
If you need any assistance or if you have questions about this item, call our Tech Help Line at
(254) 848-4300. Do not use this product without filling it with water or immediate damage can result.
All Hot Water Bottle Baths are leak tested before shipping.
Step 1:
Check the hot box to ensure it is clean of any debris, and
that the thermostat probe is not damaged.
Step 2:
Fill the box with 3.8 to 4 gallons of water.
Step 3:
Plug the box into a 110V outlet. When the unit turns on, it
will display the current water temperature.
W W W. N I T R O U S O U T L E T. C O M / I N S TA L L AT I O N - G U I D E S . C O M
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 |
P : 2 5 4 - 8 4 8 - 4 3 0 0 | W W W. N I T R O U S O U T L E T. C O M
©N2O101017
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
HOT WATER BOTTLE BATH
PART NUMBER 00-64002
INSTALLATION INSTRUCTIONS
Step 4:
To enter the programming menu, press and hold the button
labeled ‘SET’.
Step 5:
The first option is to select degrees Fahrenheit or Celsius.
Press the up and down buttons to select either F or C.
Press ‘SET’ to save the setting and move to the next step.
Step 6:
Press the up or down buttons to select the temperature
you want the water to be. Press ‘SET’ when you are on
the desired temperature. See the Temperature vs Nitrous
Pressure chart at the back of these instructions for more
information.
Step 7:
The option labeled DIF is to set the acceptable variance
from the set temperature. Setting this option to ‘1’ will
keep the water within 1 degree of the set temperature.
Use the up and down buttons to select the desired variance,
and press ‘SET’ to save the setting.
W W W. N I T R O U S O U T L E T. C O M / I N S TA L L AT I O N - G U I D E S . C O M
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 |
P : 2 5 4 - 8 4 8 - 4 3 0 0 | W W W. N I T R O U S O U T L E T. C O M
©N2O101017
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
HOT WATER BOTTLE BATH
PART NUMBER 00-64002
INSTALLATION INSTRUCTIONS
Step 8:
The last option is to set the mode of the thermostat. This
needs to be set to ‘H1’ for heat mode. Press the ‘SET’
button to save the setting and return to the home screen.
After all programming options have been set, the heater will
turn on.
Step 9:
To lock the settings on the thermostat, remove the face of
the thermostat and flip the switch located on the back of
the face.
This section will outline general maintenance for your Hot
Water Bottle Bath. During maintenance, please ensure
that your Hot Water Bottle Bath is unplugged in order to
avoid serious injury or death due to electrical shock.
Step 1:
Use a Phillips Screwdriver to remove the 4 screws on the
face of the thermostat.
Step 2:
Remove the face of the thermostat very carefully to avoid
damaging any wires or connections.
W W W. N I T R O U S O U T L E T. C O M / I N S TA L L AT I O N - G U I D E S . C O M
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 |
P : 2 5 4 - 8 4 8 - 4 3 0 0 | W W W. N I T R O U S O U T L E T. C O M
©N2O101017
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
HOT WATER BOTTLE BATH
PART NUMBER 00-64002
INSTALLATION INSTRUCTIONS
Step 3:
When the control box is open, the wiring should look exactly
like the wiring in this picture. In the event your heater isn’t
working properly, ensure that the wires are connected
correctly.
Upper right junction - Black wire from heater element and
black wire from power cord
Upper middle junction - Red jumper wire
Lower right junction - White wire from power cord and red
jumper wire from upper middle junction
Lower middle junction - red wire from heater
Lower right ground screw - green wire from power cord
Heater Element Replacement
Step 1:
Remove the front cover of the Hot Water Bottle Bath with
a Phillips Screwdriver. Then, use a Phillips Screwdriver to
disconnect the wires from the heater element.
Step 2:
Remove the four 9/16” Bolts and Nuts that secure the
element.
W W W. N I T R O U S O U T L E T. C O M / I N S TA L L AT I O N - G U I D E S . C O M
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 |
P : 2 5 4 - 8 4 8 - 4 3 0 0 | W W W. N I T R O U S O U T L E T. C O M
©N2O101017
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.
HOT WATER BOTTLE BATH
PART NUMBER 00-64002
INSTALLATION INSTRUCTIONS
Step 3:
Remove the element from the Hot Water Bottle Bath.
Step 4:
Replace the heater element, and ensure the gasket is in
proper position. Before tightening the bolts and nuts, use
a thread sealer like Blue Loc-Tite on the full length of the
threads to prevent water from leaking out of the bath.
Nitrous Pressure vs. Temp F°
Heater Specifications:
65° F = 715PSI
70° F = 760PSI
75° F = 810PSI
80° F = 765PSI
85° F = 920PSI
110-120VAC
1500 Watts
14A Max Draw
3.8-4.0 Gallon Capacity
90° F = 980PSI
95° F = 1040PSI
100° F = 1090PSI
105° F = 1130PSI
110° F = 1160PSI
W W W. N I T R O U S O U T L E T. C O M / I N S TA L L AT I O N - G U I D E S . C O M
NITROUS OUTLET | 305 SOUTH 28TH STREET | WACO, TX 76710 |
P : 2 5 4 - 8 4 8 - 4 3 0 0 | W W W. N I T R O U S O U T L E T. C O M
©N2O101017
IMPORTANT- ALL APPROPRIATE SAFETY EQUIPMENT (GLOVES, TOOLS ETC.) MUST BE USED DURING THE INSTALLATION OF THIS PRODUCT(S). NITRO DAVE’S LLC ACCEPTS NO
RESPONSIBILITY FOR INJURIES RESULTING IN THE INSTALLATION OF ANY PRODUCT(S). NITROUS OXIDE IS FOR OFF-ROAD USE ONLY.