Fully Integrated Dishwasher MDI450-2 - Slimline 45cm

THE PERFECT BALANCE OF FUNCTION AND STYLE
LAUNDRY - DISHWASHING - COOKING - COOLING
Installation and Operating Instructions
Fully Integrated Dishwasher
MDI450-2 - Slimline 45cm
Please read these instructions carefully before attempting to install or use this appliance.
We recommend that you keep these instructions in a safe place for future reference.
Welcome
Thank you for choosing this Montpellier Integrated Dishwasher.
Our Integrated Dishwasher has been designed to provide you with the best combination of style, reliability and
performance to give you years of trouble-free use.
You may be familiar with a similar product, but please take time to read these instructions carefully before installing or
using your Integrated Dishwasher to ensure you get the most from your purchase.
We recommend that you keep this manual in a safe place for future reference.
Your Integrated Dishwasher is covered by a comprehensive two year Parts &
Labour Guarantee. In the unlikely event that you experience a problem with your
Integrated Dishwasher, you can rest assured that you are fully protected against
the cost of repairs for the first 24 months . Please note that any claim must be
accompanied by the model reference number, serial number and proof of purchase.
YEAR
GUARANTEE
PARTS & LABOUR
ACROSS ALL OUR MODELS
www.montpellier-appliances.com
To activate your guarantee, you will need your product serial number. This can be
found on the rear of the machine.
There are two ways to register your Guarantee:
Visit the Support page on our website and complete the online Product
• Online:
Registration form. www.montpellier-appliances.com
y Post: Simply detach and fill in the form provided, attach a stamp and send
• B
it in the post. Don’t forget to include your e-mail address so that we can send
confirmation through to you.
Note: W
e are unable to take registrations over the phone.
Description of the Appliance
1.
2.
3.
4.
5.
6.
7.
8.
Upper basket with racks
Upper spray arm
Lower basket
Lower spray arm
Filters
Rating plate
Control Panel
Detergent and rinse-aid
dispenser
9. Cutlery basket
10. Salt dispenser
11. Upper basket track latch
12
Fixed Top Sprinkler: Provides
better washing performance
for utensils in the upperbasket.
3
CONTENTS:
Section 1. Installation
Section 2. Safety Advice
Section 3. Operating the Appliance
Section 4. Maintenance
4
Section 1. Installation
• Position the appliance in a dry, well ventilated room with a solid level floor. The
room temperature must not fall below +5° or rise above +35°.
• This appliance is fitted with adjustable feet so that you can ensure it is sitting
level. Adjust the feet by turning left or right until the appliance is level.
• The adjustable feet must never be removed.
• Plug the 3pin moulded plug into a nearby 13amp plug socket. Always make
sure that you can easily gain access to switch the power on or off at the plug
socket.
• N.B. This appliance must be earthed!
• If you have installed this appliance underneath a work surface the plug socket
•
•
•
•
•
•
•
should have a fused switch located above the work surface so that you can
easily switch the appliance on or off.
You are advised to turn the power off at the plugsocket when you have
finished using your appliance.
Before using the appliance for the first time, you must set the water softener,
add salt, add rinse aid and add detergent.
Your plumber will connect the water hose (supplied) to the water inlet
connection at the rear of the appliance and to an adjacent cold water supply. It
is your responsibility to ensure that the supplied washers have been used and
that both connections are water tight.
Ensure water pressure is within the range specified on the Rating Label. Your
plumber will connect the water drain pipe to an adjacent sink (see Pic.1 below)
Ensure that the water hose and water drain pipe are not kinked when the
appliance is pushed into place. If either of these pipes is kinked the appliance
will not operate correctly.
Ensure that the appliance is not standing on the power cable or hoses.
Do not use the water inlet hose of your old machine. Use the new water inlet
hose and connect the hose directly to the water inlet tap. The pressure
supplied by the tap should be a minimum of 0.03 Mpa and at a maximum of 1
Mpa. If the water pressure is above 1 Mpa, a pressure relief valve should be
fitted.
After the connections are made, the tap should be turned on fully and checked
that it is water tight. You should always turn off the water inlet tap after a wash
programme is finished.
Note: An Aquastop water hose is used in some models. In such
circumstances, heavy tension will exist. Do not cut the Aquastop water hose
and do not let it get folded or twisted.
5
Water Outlet Hose
The water drain hose can be connected either directly to the water
drain hole or to the sink outlet spigot using a special bent pipe (if
available). The hose connection should be at a minimum of 50cm and
at a maximum of 110 cm from the floor.
Please note that a drain hose longer than 4m must not be used as it
may prevent the appliance from washing correctly.
6
Section 2. Safety Advice
• This appliance is manufactured and intended for DOMESTIC use only. Any
•
•
•
•
•
•
•
guarantee offered with the appliance is not valid for any installation in a
commercial environment.
This appliance MUST BE EARTHED!
Never try and disconnect the power by pulling the supply cable – hold the plug
firmly and pull it out of the socket.
Never touch the plug or power cable with wet hands.
Check the power cable periodically for signs of damage and ensure that it is
not trapped underneath the appliance. If the cable is damaged, turn off the
power at the socket and arrange for a qualified electrician to replace the cable.
Never remove the power cable, open the appliance cabinet or try to modify
the appliance in any way. All service work must be carried out by a qualified
electrician.
The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
the use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
Ensure that the appliance is sited well away from other heat sources, i.e. open
fires, boilers etc and in a dry, well ventilated room. The temperature must not
fall below +5° or rise above +35°.
• Do not sit on the appliance or stand on the open door – the appliance could tip
forwards.
• Keep children away from detergent and rinse aid, keep children away from the
open door of the dishwasher, there could still be some detergent left inside.
• This appliance is not a toy – ensure that children are supervised at all times
whilst in the vicinity of thisappliance.
• Take care when loading the baskets with knives and cutlery. Always ensure
that sharp points are pointing away from you or down into the basket.
• Only wash crockery and utensils that are clearly marked ‘dishwasher safe’.
• Do not wash plastic items unless they are clearly marked ‘dishwasher safe’.
• Only use dishwasher detergents and rinse aid clearly marked for use with
automatic dishwashers.
• Never use non dishwasher detergent in this appliance, i.e. hand soap, washing
machine detergent, washing up liquid etc.
• Always add dishwasher salt to your dishwasher, even when using 3-in-1
tablets. This will help protect your appliance against limescale.
• If the power supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a hazard.
7
Section 3. Operating the Appliance
3.1.
Before Operating the Appliance
3.1.1. Adding Salt
•
•
•
•
•
•
Remove the lower basket and then unscrew the salt container cap (1).
Add water and approximately 1kg of specialist dishwasher salt to the
container until almost overflowing. N.B. It is normal for a small amount
of water to come out of the container whilst filling it with salt. Note: Fill
the salt compartment with water at first use only.
Now replace the screw cap correctly and ensure that it is tight. If not,
salt may leak into the dishwasher chamber which can be detrimental
to the stainless steel interior. This is not covered by the manufacturers
guarantee.
After adding salt you should run a programme immediately to activate
the water softener and flush away any salt spilled into the machine.
If salt is low the indicator light will show on the control panel.
3.1.2. Adding Rinse Aid
8
•
•
•
•
Remove the Rinse Aid Filler Cap (1).
Add Rinse Aid until the rinse aid level indicator becomes dark (2).
Replace the Filler Cap (3).
If the rinse aid level is sufficient the indicator light will be dark on the
control panel (2B). If more rinse aid is required the indicator will be
light (2A).
3.1.3. Adding Detergent
Use specialist dishwasher detergent powder or dishwasher tablets in
this appliance. However, please note that tablets do not always dissolve
fully during shorter wash programmes, so you are advised to operate
your appliance on a longer wash programme if using tablets.
In addition, the use of tablets may result in spots appearing on dishes
and glasses.
Push the latch to open the detergent container as shown in image 1. The
detergent pod has “level” lines inside to help measure the amount of
detergent you use. The pod can take a total of 40cm³ of detergent. If your
dishes are heavily soiled pour 25cm³ of detergent into the
larger compartment (b), if they are less soiled use only 15cm³.
If the programme selected has a pre-wash cycle you should add 5cm³
of detergent to the pre-wash compartment (a).
If using combined detergents, make sure to check the specifications
on the product to ensure that it is appropriate for the wash programme,
your machine and the level of hardness of the mains water.
9
3.1.4. Combined Detergent – Recommended Usage
If you are using a combined detergent, add a rinse aid agent to your machine
and switch the rinse agent setting to its lowest position (1) and activate the
tablet detergent button in order to obtain better results. Depending on the
water hardness you may need to fill the salt container with salt.
We do not recommended using 3 in 1 tablets on fast or rapid programmes
as the tablet may not fully dissolve. For these programs we suggest using
normal dishwasher powder.
3.1.5. Adjusting the Water Softener
The water softener in your appliance has been pre-set to the midsetting, but if you need to change the setting please proceed as
follows:
2
3
After resetting your machine, press the program selection button and keep it
pressed down.3
Start the machine by pressing the Power On/Off button. 1
Keep the program selection button pressed until “8” disappears from the
display.3
Release the program selection button after “8” disappears from the display.
3 The machine displays the last selected water hardness setting.
Water hardness can be adjusted by the programme selection button .3
according to Table of Water Hardness Level Settings.
After adjusting the water hardness level , press on/off button to save settings
in memory.1
Water
hardness
level
British
hardness
dE
Hardness Level Indicator
1
0-6
L1 displays.
2
7-14
L2 displays.
3
15-21
L3 displays.
4
22-28
L4 displays.
5
29-42
L5 displays.
6
43-63
L6 displays.
10
3.2. The Control Panel
1. Power On/Off Button
2. Programme Display – Indicates the selected programme number.
3. Programme Selection Button – Allows you to select a suitable programme.
4. ½ Load Button – By using this feature, you can reduce the duration of selected
programs, and decrease the power and water consumption of your machine.
5. Delay Timer Button – You can delay the start of a programme by 3, 6 or 9 hours
by pressing this button. The delay will increase by 3 hours each time the button is
pressed, once you have the required delay press the programme selection
button. If you wish to change or cancel the delay, you can adjust it with the delay
timer button as it will be activated/deactivated according to the last value entered.
6. Salt Warning Indicator – When your machine needs salt the salt warning
indicator will come on. When this happens, add more salt.
Rinse Aid Warning Indicator – When there is insufficient rinse aid in your
machine the rinse aid warning indicator will come on. When this happens, fill the
rinse aid chamber.
End of Programme Indicator – When a programme has ended the end of
programme indicator will come on. Additionally your machine will sound a buzzer
5 times.
11
3.3.
Loading the Baskets
3.3.1. Upper Basket
There are folding racks on the
upper basket of your machine.
You can use these racks in an
open or closed position
depending on whether you
want to place cups, long
glasses, or cutlery on them
Ensure that items are not
blocking the rotation of the
top spray arm.
Upper Basket Height Adjustment
The upper baskets location can be
altered as shown in the image to the
left.
The benefit of this is by dropping or
moving the basket up in the
machine you will have more space
either below or above for larger
items.
In order to change the height,
remove the basket by shifting the
clip at the end of the rail to the side.
You can then reposition the basket
on the other wheels, do not forget to
shift the clip at the end of the rail
back into position to lock the basket
and prevent it from sliding out.
12
3.3.2. Alternate Basket Loads
Lower Basket
Upper Basket
Incorrectly Distributed Loads
13
14
17,6
15,1
115
1,33
Intensive
1,31
124
11,0
0,73
1,08
10,5
198
medium
coffee,milk,tea,cold
50
Rinse
medium
65°C ( P3)
10
0,71
30
coffee,milk,tea,cold
3,5
0,02
15
Prewash
The values declared above are the values obtained under laboratory conditions according to relevant standards. These values can change depending on
conditions of product’s use and environment (network tension, water pressure, water input temperature and environment temperature).
Warning : Short programs do not include a drying step.
Electricity
consumption
(kW hours)
Water consumption
(liters)
3
Programme duration
(min.)
B: 25 cm / 15 cm
3
A: 5 cm
3
Programme names
Programme No
3.4.
Programme Selection Table
3.5. Selecting a Programme
1
Machine is started when the On/Off button is
pressed,one dash appears in the programme display
and the end of programme indicator turns on.
2
3
When you select a programme with the
programme selection button, the
programme you select (1, 2, etc) appears on
the programme display and the end of
programme indicator turns off.
1. Press the Power On/Off key.
2. Select the programme best for your dishes via the Programme Selection
button.
3. If desired you can choose additional functions.
4. Close door. The program starts automatically.
Note: If you decide not to start the machine after selecting the programme, just press the on/
off button. Your machine will be ready for a new programme to be selected after pressing
the on/off button. You may now select a new programme.
Programme follow-up
The end of programme indicator on the control
panel will turn on when the selected washing
programme has finished. Your machine will also
sound a buzzer 5 times when completed..
Changing a programme
If you would like to change programmes while a wash programme is in progress do the following.
Open the door and select a new
programme by pressing the
After closing the door , the
resume in place of the old
programme.
Note: When the door of the machine is opened in order to stop a wash programme before it is
completed, ensure that you open the door slightly to avoid water spillage.
15
Chancelling a Programme
Open the door of your machine.
The last selected programme
will appear on the screen.
Keep the programme selection button pressed for
3 seconds. The End of Programme indicator will
flash and “Select Programme Number” will be
displayed on the programme display.
The discharge process will start after the
door is closed. The machine discharges
water for roughly 30 seconds. When the
programme is cancelled your machine will
make a buzzer sound for 5 times and the
“end of programme indicator” will turn on.
Note: When the door is opened in order to stop the washing programme before
completion. Ensure that the door is opened only slightly to avoid water spillage.
Switching the machine off
When end of programme indicator
comes on , switch your machine
off by using the Power On/Off
button.
Switch off at the plug socket.
Note: Once your wash programme has finished, leave the dishwasher door slightly ajar to help aid
the drying process.
16
Section 4. Maintenance
4.1. Cleaning the Filter
The filter helps prevent large pieces of food or other items entering the
pump and causing damage. It is important that you examine and clean the
filter system on a regular basis. Blocked filters are not covered under the
Guarantee!
The filter assembly is located
inside the appliance just
underneath the lower spray arm.
To remove the filter assembly,
turn it anti-clockwise and lift
the assembly out.
Pull out the metal/plastic filter and
then pull the coarse filter out of
the micro filter.
Rinse with lots of water under the
tap before refitting.
a. Micro Filter b. Coarse Filter c. Metal/Plastic Filter
4.2. Cleaning the Door
Periodically clean the inner stainless steel lining of the door with a warm
damp cloth. Pay particular attention to the edges so that food deposits
do not build up, causing the door seal to fail. Clean the door seal with
warm soapy water.
Never use abrasive cleaners or polishes on the stainless steel!
17
4.3. Cleaning the Spray Arms
Small particles of food will over time get into the spray arms and cause
blockages. Periodically remove the spray arms (as shown below) and
wash them in warm soapy water. Blocked spray arms are not covered
under the Guarantee!
To remove the lower spray arm
pull it upwards, so that the upper
spray arm nut can be removed by
turning the nut to the left.
Be sure that the nut is perfectly
tightened when refitting the
upper spray arm.
4.4. Daily Maintenance
Follow these useful tips to ensure your dishwasher stays in tip-top
working order:
• Always switch off the power supply at the socket when your dishwasher
•
•
•
•
•
•
•
•
is not in use.
Always pay particular attention to the filter and spray arms – give them a
regular clean as described in 4.1. and 4.3 above.
Clean the door edges and door seal as described in 4.2. above.
Add salt to your appliance when prompted by the salt light on the control
panel. Always run a programme after to remove any spilled salt.
Add rinse aid to your appliance when prompted by the rinse aid light on
the control panel.
Only use Dishwasher salt, Dishwasher detergent and Dishwasher rinse
aid in your dishwasher.
Never use abrasive cleaners to clean your appliance.
When the appliance is not in use, leave the door slightly ajar in order to
avoid moisture and odours building up inside. However, this may not be
advisable if small children have unsupervised access to the area where
the dishwasher is sited.
If you are vacating the house for a long period, run a rinse cycle through
the machine and then ensure that the water and power supplies to the
dishwasher have been turned off. Leave the door ajar.
18
4.5. Error Codes
Error
Code
Error Description
F5
Inadequate water supply
F3
Continuous water input
F2
The waste water in the
machine cannot be
discharged
F8
F1
Heater error
Alarm is active showing
water overflow
FE
F7
F6
Faulty electronic card
Overheating error
Faulty heater sensor
Control
Make sure the water inlet tap is totally open and that there is
no water leak
Close the water inlet tap, remove the water inlet hose from
the tap and clean the filter at the connection end of the hose
Restart your machine, contact the Repairtech helpline if the
error resumes
Turn off the tap
Contact the Repairtech helpline
Water discharge hose is clogged
The filters of your machine might be clogged
Power on/off your machine and activate the program
cancel command
If the error continues, contact the Repairtech helpline
Contact the Repairtech helpline
Power off your machine and turn off the
tap Contact the Repairtech helpline
Contact the Repairtech helpline
Contact the Repairtech helpline
Contact the Repairtech helpline
19
4.6. Before Calling Service
If you appear to have a problem with your dishwasher, please take a few
minutes to check the following ‘trouble shooting’ guide. The problem may
be easily solved without the need for a service call.
Dishwasher Will Not Start
•
•
•
•
•
Is the power on at the socket?
Is the Start/Pause button set to pause?
Have you checked the fuse in the plug?
Is the dishwasher door closed correctly?
Is your water pressure low – if yes, wait until normal pressure is resumed
Water Left In Bottom of Dishwasher
•
•
Check & clean the filter
Make sure the drain hose is not trapped/kinked
Soap Suds in the Dishwasher
•
•
Are you using the correct dishwasher detergent/tablets? You must only
use specialist dishwasher detergent in a dishwasher
You may have spilled rinse aid into the dishwasher whilst topping up the
dispenser – it will clear after one or two rinse or wash programmes.
There Are Rust Stains on the cutlery
•
•
Your utensils may not be dishwasher safe – you must use dishwasher
safe utensils
You may have spilled salt into the dishwasher whilst topping up the salt
dispenser and not run a programme to flush it away (see 3.1.1 - Page 9)
20
Knocking Noise From Inside the Cabinet
•
•
The spray arm is catching against an item in the basket – reposition the
items
Items of crockery are loose in the basket and water pressure is causing
them to move – reposition the items of crockery
The Crockery is not Clean
•
•
•
•
•
Ensure that you load items correctly – do not stack items on top of other
items
You selected the wrong wash programme – select a stronger wash
Did you use enough detergent?
Have you cleaned the spray arms recently?
Have you cleaned the filters recently?
The Glasses are Cloudy
•
•
•
Are your glasses dishwasher safe? You must only place dishwasher safe
glassware in a dishwasher
Soft water can leave cloudy marks on glassware
Too much detergent can cause cloudy marks on glassware
The Crockery is not Drying
•
•
•
Ensure you load the baskets with space around the items
Check your rinse aid – top up the dispenser
Do not unload your dishwasher too soon - allow the drying process time
to work
Warning!
If your dishwasher overflows or develops a water leak, you must turn off both
the water and power supplies until an engineer has corrected the
fault!
21
Technical Specifications
Capacity
Height
Width
Depth
Net Weight
Electricity Input
Total Power
Heating Power
Pump Power
Drain Pump Power
Water Supply Pressure
Current
10 Place Settings
820mm – 870mm
450mm
596mm
32kg
220-240 V, 50Hz
1900W
1800W
100W
30W
0.03 Mpa (0,3 bar) – 1 Mpa (10 bar)
10 A
gff
22
Here For You
After-sales assistance
If you continue to experience problems with your Integrated Dishwasher, please call the Montpellier customer
service helpline on: 03333 234 473.
Please have all your product details available, including the model number, serial number, date of purchase,
and your retailer’s details before registering a fault.
The service call cannot progress without this information.
Your 2 year Manufacturer’s guarantee
THIS DOES NOT AFFECT YOUR STATUTORY RIGHTS.
Your new Montpellier appliance carries a free guarantee which protects you against the cost of repairs during the
first 24 months from date of purchase provided that:
Any claim is accompanied by evidence of the model reference, model serial number and proof of purchase, such
as a Sales Receipt, showing that the appliance was purchased within the 24 months prior to the date
of claim.
• Any appliance not correctly installed and operated in accordance with the manufacturer’s instructions.
• Any appliance that is used for anything other than domestic purposes.
• Any defect caused by accident, misuse, unauthorised modification or inexpert repair.
• Cost of Call-out where a fault cannot be found with the appliance.
• Cost
of Call-out for work covering routine maintenance, such as, but not exclusively, cleaning of filters or
defrosting.
of Call-out for work required to correct the alignment of doors following door reversal procedures carried
• Cost
out by you.
• Use of the appliance by anyone other than the Householder.
• Use in any commercial environment.
• Consumable
items, such as, but not exclusively, fuses in plugs, bulbs and breakable items which require
routine replacement.
costs incurred that have not been authorised by Repairtech and/or carried out by a non-approved
• Repair
Repairtech engineer.
YOUR GUARANTEE IS VALID ONLY IN THE UK & ROI.
To register your appliance simply complete the card in your appliance pack and return it with a stamp affixed or
alternatively you can register online at www.montpellier-appliances.com/support
SERVICE HELP-LINE
Should your appliance develop a fault, please call the Montpellier customer service helpline on: 03333 234 473.
Please remember to have all your product details available, including the model number, serial number, date of
purchase and your retailer’s details before registering a fault.
Your service call cannot progress without this information.
Here For You
What is not covered under the Guarantee
Montpellier Domestic Appliances Ltd.
Unit 1, Tewkesbury Retail Park, Northway Lane,
Tewkesbury, Gloucestershire GL20 8JU
www.montpellier-appliances.com
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Download PDF
Similar pages
Franke FDW 613 DTS A+++
Franke FDW 410 DH 3A
Franke FDW 612 EHL A+
Franke FDW 410 DT 3A
AEG F45010W0
LG LDF7551BB Installation Manual
Franke FDW 612 E5P A+
Installation Guide (5.90 MB)