Все оригинальные аксессуары к вашей технике на одной

Все оригинальные аксессуары к вашей технике
на одной странице
5713215191/02.11
2
bean to cup espresso and
cappuccino machine
Instruction for use
ECAM26.455
1
B2
B3
B4
B5
B6
B1
B7
B13
B8
B9
B10
B11
B12
D1
D2
C2
C1
A18
C3
C4
C5
D3
D4
C6
D5
2
D6
A1
A2
A5
A3
A6
A4
A11
A12
A7
A13
A8
A14
A9
A15
A16
A10
A22
A18
A17
A20
A19
A21
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
17
18
19
20
CLEAN
21
22
23
24
25
26
27
28
B
PU
SH
A
PU
SH
29A
B
29B
30
31
5
32
A
Contents
MAKING DRINKS WITH MILK...................................13
Filling and attaching the milk container.................................. 13
Adjusting the amount of froth................................................. 13
Making drinks with milk automatically.................................... 14
Cleaning the milk frother with the CLEAN button . ................. 14
Programming the quantity of coffee and milk in the cup for the
CAFFELATTE, CAPPUCCINO, MACCHIATO and MILK buttons....... 14
Introduction........................................................7
Symbols used in these instructions............................................ 7
Letters in brackets...................................................................... 7
Troubleshooting and repairs...................................................... 7
SAFETY....................................................................7
Fundamental safety warnings................................................... 7
DELIVERING HOT WATER AND STEAM.......................14
Delivering hot water ............................................................... 14
Change the quantity of water delivered automatically. . ......... 14
Delivering steam...................................................................... 15
Tips for using steam to froth milk............................................. 15
Cleaning the spout after use.................................................... 15
DESIGNATED USE......................................................7
INSTRUCTIONS.........................................................7
DESCRIPTION...........................................................8
Description of the appliance . .................................................... 8
Description of the control panel................................................. 8
Description of the milk container............................................... 8
Description of the accessories.................................................... 8
CLEANING..............................................................15
TURNING THE APPLIANCE ON....................................9
Cleaning the coffee grounds container..................................... 15
Cleaning the drip tray and condensate tray.............................. 15
Cleaning the inside of the coffee maker................................... 16
Cleaning the water tank........................................................... 16
Cleaning the coffee spouts....................................................... 16
Cleaning the pre-ground coffee funnel.................................... 16
Cleaning the infuser................................................................. 16
Cleaning the milk container..................................................... 16
Cleaning the hot water/steam nozzle...................................... 17
TURNING THE APPLIANCE OFF ..................................9
DESCALE................................................................17
MENU SETTINGS.......................................................9
SETTING THE WATER HARDNESS..............................18
PRELIMINARY CHECKS..............................................8
Checking the appliance.............................................................. 8
Installing the appliance............................................................. 8
Using the appliance for the first time......................................... 9
Rinsing..................................................................................... 10
Descale.................................................................................... 10
Adjust time.............................................................................. 10
Auto-off................................................................................... 10
Auto-start................................................................................ 10
Setting the temperature.......................................................... 10
Energy Saving.......................................................................... 10
Cup warmer............................................................................. 11
Setting water hardness............................................................ 11
Setting the language .............................................................. 11
Install filter.............................................................................. 11
Replacing the filter.................................................................. 11
Beep........................................................................................ 11
Cup lighting............................................................................. 11
Default values (reset)............................................................... 11
Statistics function.................................................................... 11
Measuring water hardness....................................................... 18
Set water hardness.................................................................. 18
WATER FILTER........................................................18
Installing the filter................................................................... 18
Replacing the filter.................................................................. 19
Removing the filter.................................................................. 19
TECHNICAL SPECIFICATION......................................19
DISPOSAL...............................................................19
DISPLAYED MESSAGES............................................20
TROUBLESHOOTING................................................21
MAKING COFFEE.....................................................12
Selecting the coffee taste......................................................... 12
Selecting the quantity of coffee in the cup . ............................ 12
Customising the “my coffee” quantity . .................................... 12
Adjusting the coffee mill.......................................................... 12
Tips for a hotter coffee............................................................. 12
Making coffee using coffee beans............................................ 12
Making coffee using pre-ground coffee................................... 13
6
Introduction
•
•
Thank you for choosing the ECAM 26.455 automatic coffee and
cappuccino maker.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
•
•
Symbols used in these instructions
IMPORTANT WARNINGS ARE IDENTIFIED BY THESE SYMBOLS.
It is vitally important to observe these warnings.
•
•
Danger!
Failure to observe the warning could result in life threatening
injury from electric shock.
•
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
•
Danger of burns!
Failure to observe the warning could result in scalds.
Please note:
This symbol identifies important advice or information for the
user.
Never touch the plug with damp hands.
Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
Unplug directly from the plug only.
Never pull the power cable as you could damage it.
To disconnect the appliance completely, release the main
switch at the back of the appliance by pressing it (fig. 2).
If the appliance is faulty, do not attempt to repair.
Turn it off, unplug from the mains socket and contact
Customer Experience.
If the plug or power cable is damaged, it must be replaced
by De’Longhi Customer Experience only to avoid all risk.
Important!
Keep all packaging (plastic bags, polystyrene foam) away
from children.
The appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children must be supervised to ensure
they do not play with the appliance.
Danger: Risk of burns!
This appliance produces hot water and steam may form while
it is in operation.
Avoid contact with splashes of water or hot steam.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the section “Displayed messages” on
page 20 and “Troubleshooting” on page 21.
If this does not resolve the problem or you require further
information, you should consult Customer Experience by calling
the number given on the annexed “Customer Experience”
sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact De’Longhi Customer Experience
only.
Contact details are given in the guarantee certificate provided
with the appliance.
DESIGNATED USE
This appliance is designed and made to prepare coffee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from
improper use of the appliance.
This is an household appliance only.
It is not intended to be used in:
• staff kitchen areas in shops, offices and other working
environments;
• farm houses;
• by clients in hotels, motels and other residential type
environments;
• bed and breakfast type environments.
SAFETY
Fundamental safety warnings
INSTRUCTIONS
Read these instructions carefully before using the appliance.
- Failure to follow these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
Danger!
This is an electrical appliance and may cause electric shock.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands or feet.
7
B10.latte macchiato button: to deliver a macchiato
B11.milk button: to deliver a cup of milk (When in the settings
menu, press to scroll forwards)
B12:
button: to deliver steam
B13.
button: to make 2 cups of coffee with the
settings displayed
failure to respect these instructions.
Please note:
Keep these instructions
If the appliance is passed to other persons, they must also be
provided with these instructions.
Description of the milk container
(page 3 - C )
C1. Milk container lid
C2. Froth adjustment dial
C3. CLEAN button
C4. Frothed milk spout (adjustable)
C5. Milk carafe
C6. Milk intake tube
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Beans container lid
A2. Top lid
A3. Grinding adjustment dial
A4. Beans container
A5. Pre-ground coffee funnel lid with pressure lock
A6. Pre-ground coffee funnel
A7. Main switch
A8. Socket for power cable connector
A9. Infuser
A10. Infuser door
A11. Cup warmer shelf
A12. Control panel
A13. Coffee spout (adjustable height)
A14. Hot water and steam nozzle
A15. Condensate tray
A16. Water tank lid
A17. Water tank
A18. Water filter
A19. Cup tray
A20. Drip tray water level indicator
A21. Drip tray
A22. Coffee grounds container
Description of the accessories
(page 2 - D )
D1. Pre-ground coffee measure
D2. Cleaning brush
A18. Water filter (certain models only)
D3. Cappuccino maker/hot water spout
D4. Power cable
D5. “Total Hardness Test” indicator paper
D6. Descaler
PRELIMINARY CHECKS
Checking the appliance
After removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact De’Longhi Customer Experience.
Installing the appliance
Description of the control panel
(page 2 - B )
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
B1.
button: turns the appliance on and off
B2.
button: to select the coffee quantity
B3. MENU/ESC button to access the menu or exit from the
selected function
B4. Display: guides the user in using the appliance.
B5.
button: to deliver hot water (When in the settings
menu, press to confirm the selection)
B6.
button: to make 1 cup of coffee with the settings
displayed
B7.
aroma selection button: to select the coffee
taste
B8. caffelatte button: to deliver a caffelatte
B9. cappuccino button: to deliver a cappuccino (When in
the settings menu, press to scroll backwards)
Important!
When installing the appliance, respect the following safety
warnings:
• The appliance gives off heat. After positioning the appliance on the worktop, leave
a space of at least 3 cm between the surfaces of the
appliance and the side and rear walls and at least 15 cm
above the coffee maker.
• Water penetrating the coffee maker could cause damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
8
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an earthed and correctly installed
socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch on
the back of the appliance is pressed (fig. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
Using the appliance for the first time
Danger of burns!
During rinsing, a little hot water comes out of the coffee spouts
and is collected in the drip tray underneath.
Avoid contact with splashes of water.
Please note!
• Coffee has been used to factory test the appliance and it
is therefore completely normal for there to be traces of
coffee in the mill.
The machine is, however, guaranteed to be new.
• You should customise water hardness as soon as possible
following the instructions in the section “Setting the
water hardness” on page 18.
1. Insert the power cable connector into the socket at the
back of the appliance and connect the appliance to the
mains electricity supply (fig. 1). Make sure the main
switch at the back of the appliance is pressed (fig. 2).
You must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When “English” appears, press and hold the
button (fig. 3) for a few seconds until “English set” is
displayed.
Follow the instructions displayed by the appliance:
3. “FILL TANK!”: remove the water tank (fig. 4), fill to the
MAX line with fresh water then replace in the appliance.
4. “INSERT WATER SPOUT!”: Check that the hot water spout
is inserted on the nozzle and place a container with a
minimum capacity of 100 ml underneath (fig. 6).
5. “Hot water... Press OK?” is displayed;
6. Press the
button to confirm (fig. 3). The
appliance delivers water from the spout then goes off
automatically.
The coffee maker is now ready for normal use.
•
•
If your model is not provided with a filter, you can request
one from De’Longhi Customer Experience.
•
To turn the appliance on, press the
button (fig. 7).
The message “Heating up... Please wait” is displayed.
After heating, the message “Rinsing...” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance has reached the required temperature when a
message is displayed indicating the coffee taste and quantity.
TURNING THE APPLIANCE OFF
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
Avoid contact with splashes of water.
To turn the appliance off, press the
button (fig. 7).
The appliance performs a rinse cycle, then the message
“Turning off underway Please wait...” is displayed and the
appliance goes off.
Please note!
If the appliance is not used for an extended period, switch off
the machine at the main switch (fig. 2).
Important!
To avoid damaging the appliance, never switch the appliance
off at the main switch before it has been turned off using the
button.
Please note!
When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory results.
To help reduce the buildup of limescale in the appliance
and soften the water taste, we recommend installing a
water filter as described in the section “WATER FILTER”.
MENU SETTINGS
When you access the programming menu by pressing the MENU/ESC
button, the following menu items are available:
9
Rinsing
Use this function to deliver hot water from the spout to heat the internal
circuit and make the coffee delivered hotter.
To enable the function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Rinsing” is displayed;
3. Press the
button. The message “Confirm?” is
displayed;
3. Press the
button (fig. 3). Hot water flows out of
the spout, heating the internal circuit and making the
coffee delivered hotter.
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already have been set
correctly.
To enable Auto-on, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Auto-start” is displayed;
3. Press the
button. “Enable?” is displayed;
4. Press the
button to confirm;
5. Press the MILK or CAPPUCCINO button to choose the
hours;
6. Press the
button to confirm;
7. Press the MILK or CAPPUCCINO button (fig. 8) to change
the minutes;
8. Press the
button to confirm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been confirmed, enabling of auto-start is
indicated by the
symbol displayed alongside the time
and under the Auto-start item in the menu.
To disable the function:
1. Select auto-start from the menu;
2. Press the
button. “Disable?” is displayed;
3. Press the
button to confirm.
The
symbol is no longer displayed.
Descale
For instructions on descaling, see page 17.
Adjust time
To adjust the time on the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Adjust time” is displayed;
3. Press the
button (fig. 3);
4. Press the MILK or CAPPUCCINO button (fig. 8) to change
the hours;
5. Press the
button to confirm;
6. Press the MILK or CAPPUCCINO button (fig. 8) to change
the minutes;
7. Press the
button to confirm.
Setting the temperature
To modify the temperature of the water used to make the
coffee, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until “Set
temperature” is displayed;
3. Press the
button;
4. Press the MILK or CAPPUCCINO button until the required
temperature (●= low, ●●●● = high) is displayed;
5. Press the
button to confirm;
6. Press the MENU/ESC button to exit the menu.
This sets the time. Press the MENU/ESC button to exit the
menu.
Auto-off
The appliance is set to turn off automatically if not used for 2
hours.
The time can be changed so that the appliance switches off
after 15 or 30 minutes, or after 1, 2 or 3 hours.
To re-programme Auto-off, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Auto-off” is displayed;
3. Press the
button;
4. Press the MILK or CAPPUCCINO button (fig. 8) until the
desired operation time is displayed (15 or 30 minutes, or
1, 2 or 3 hours);
5. Press the
button to confirm;
6. Press the MENU/ESC button to exit the menu.
Auto-off is programmed.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) “energy saving” mode, proceed as
follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Energy saving” is displayed;
3. Press the
button. “Disable?” is displayed (or
Auto-start
You can set the auto-start time in order to have the appliance
10
“Enable?” if the function has been disabled);o
4. Press the
button to disable (or enable) energy
saving mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving” is displayed.
To disable or re-enable the beep, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Beep” is displayed;
3. Press the
button. “ Disable?” or “ Enable?” is
displayed;
4. Press the
button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Please note!
When in energy saving mode, a few seconds may elapse before
the first drink with milk is delivered as the appliance must heat
up again.
Cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lights come on each time coffee and drinks with milk are
made and during each rinse cycle.
To disable or re-enable this function, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until “Cup
lighting” is displayed.
3. Press the
button. “ Disable?” or “ Enable?” is
displayed;
4. Press the
button to enable or disable the cup
lighting;
5. Press the MENU/ESC button to exit the menu.
Cup warmer
This function enables or disables the cup warmer.
Proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until “Cup
warmer” appears on the display;
3. Press the
button. “Disable?” is displayed (or
“Enable?” if the function has been disabled);
4. Press the
button to disable (or enable) the
function.
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coffee hot.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as previously set).
To reset the default values, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Default values” is displayed;
3. Press the ;
button
4. The message “Confirm?” is displayed.
5. Press the
button to confirm and exit.
Setting water hardness
For instructions on setting water hardness, see page 17.
Setting the language
To change the language for the display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until “Set
language” is displayed;
3. Press the
button;
4. Press the MILK or CAPPUCCINOO button until the
required language is displayed;
5. Press the
button to confirm;
6. Press the MENU/ESC button to exit the menu.
Statistics function
This displays statistics relating to the machine.
To display, proceed as follows:
1. Press the MENU/ESC button to enter the menu;
2. Press the MILK or CAPPUCCINO button (fig. 8) until
“Statistics” is displayed;
3. Press the
button;
4. Press the MILK or CAPPUCCINO button (fig. 8) to verify:
- how many coffees have been made;
- how many times the machine has been descaled;
- the total number of litres of water delivered;
- the total number of drinks made with milk;
- how many times the water filter has been replaced.
5. Press the MENU/ESC button twice to exit the menu.
Install filter
For instructions on how to install the filter, see the section
“Installing the filter” on page 18.
Replacing the filter
For instructions on how to replace the filter, see the section
“Replacing the filter” on page 19.
Beep
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
11
MAKING COFFEE
coffee is too thin and not creamy enough or that delivery is too
slow (a drop at a time), this can be corrected by adjusting the
grinding adjustment dial (fig. 12).
Selecting the coffee taste
The appliance is set by default to make coffee with a standard
taste.
You can also choose one of these tastes:
Extra-mild taste
Mild taste
Standard taste
Strong taste
Extra-strong taste
Please note!
The grinding adjustment dial must only be turned when the
coffee mill is in operation.
If the coffee is delivered too slowly
or not at all, turn one click clockwise
towards “7”.
For fuller bodied creamier coffee on the
other hand, turn one click anticlockwise
towards “1” (do not turn more than one
click at a time otherwise the coffee could be delivered a drop
at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered.
If this adjustment does not obtain the desired result, turn the
dial another click.
To change the taste, press the
button (fig. 9)
repeatedly until the required taste is displayed.
Selecting the quantity of coffee in the cup
The appliance is set by default to make a standard quantity of
coffee.
To select the quantity of coffee, press the
button
(fig. 10) until the message corresponding to the required
quantity of coffee is displayed:
Tips for a hotter coffee
For a hotter coffee, before delivery you are recommended to:
• perform a rinse cycle by selecting the “Rinsing” function in
the settings menu (page 10)
• warm the cups with hot water (using the hot water
function);
• increase the coffee temperature in the settings menu
(page 10).
Coffee selected
Quantity in cup (ml)
MY COFFEE
Programmable:
from ≃20 to ≃180
espresso
≃40
STANDARD
≃60
LONG
≃90
Making coffee using coffee beans
EXTRA LONG
≃120
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and make it unusable.
Customising the “my coffee” quantity
The appliance is set by default to automatically deliver 30 ml
of “my coffee”.
To modify this quantity, proceed as follows:
1. Place a cup under the coffee spouts (fig. 14).
2. Press the
button (fig. 10) until “MY COFFEE”
is displayed.
3. Keep the
button (fig. 11) pressed until the message
“1 MY COFFEE Program quantity” is displayed and coffee
delivery begins. Release the button.
4. As soon as the coffee in the cup reaches the required level,
press the button
(fig. 11) again.
The quantity of coffee in the cup has now been programmed.
1.
2.
3.
Place coffee beans in the coffee bean container (fig. 13).
Place under the coffee dispensing spouts, either:
- 1 cup if you want one coffee (fig. 14);
- 2 cups if you want 2 coffees.
Lower the spouts as near as possible to the cup. This makes
a creamier coffee (fig. 15).
4. Press the button corresponding to the number of coffees
required (1 cup
or 2 cups
, figs. 11 and
16).
5. Preparation begins. The amount of coffee selected is
displayed together with a progress bar which gradually
fills as preparation progresses.
Adjusting the coffee mill
The coffee mill is preset in the factory to make coffee correctly
and should not require adjusting initially.
However, if after making the first few coffees you find that the
•
12
Please note:
While the coffee maker is making coffee, delivery can be
interrupted at any moment by pressing one of the two
MAKING DRINKS WITH MILK
coffee buttons (
or
).
At the end of delivery, to increase the quantity of coffee
in the cup, just press (within 3 seconds) one of the coffee
buttons (
or
).
Once the coffee has been made, the appliance is ready to use
again.
•
•
•
•
•
Please note!
Various alarm messages could be displayed while using
the machine (fill tank, empty grounds container, etc.).
Their meaning is explained in the section “Displayed
messages” (page 20).
For hotter coffee, see the section “Tips for a hotter coffee”
(page 12).
If the coffee is delivered a drop at a time, too weak and
not creamy enough or too cold, read the tips in the
“Troubleshooting” section on page 21.
Filling and attaching the milk container
1. Remove the lid (fig. 18);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
19). Each mark on the side of the container corresponds
to 100 ml of milk.
Please note!
• For a denser more even froth, you should use skimmed
or partially skimmed milk at refrigerator temperature
(about 5°C).
• If “Energy Saving” mode is enabled, you may have to wait
a few seconds before the first drink is delivered.
Making coffee using pre-ground coffee
•
•
Please note!
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle
as described in the section “Cleaning the milk container”
on pages 14 and 17.
Important!
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it.
This could damage the appliance.
Never use more than 1 level measure or it could dirty the
inside of the coffee maker or block the funnel.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 20).
4. Place the lid back on the milk container.
5. Remove the hot water spout from the nozzle.
6. Attach the container to the nozzle and push as far as it
will go (fig. 21). The machine emits a beep (if the beep
function is enabled).
Please note!
If you use pre-ground coffee, you can only make one cup
of coffee at a time.
7. Place a sufficiently large cup under the coffee and frothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (fig. 22).
1. Press the
button (fig. 9) until “Pre-ground” is
displayed.
2. Open the beans container lid; then open the pre-ground
coffee funnel lid by pushing on PUSH and, once released,
open the lid.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 17).
4. Place a cup under the coffee spouts.
5. Press the 1 cup coffee button
(fig. 11).
6. Preparation begins. The amount of coffee selected is
displayed together with a progress bar which gradually
fills as preparation progresses.
8. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial on the milk container lid to
adjust the amount of froth on the milk delivered while making
drinks with milk.
Dial
position
Please note!
If “Energy saving” mode is enabled, you may have to wait a few
seconds before the first coffee is delivered.
13
Description
Recommended for…
No froth
caffelatte /
MILK (hot milk)
Min. froth
macchiato
Max. froth
CAPPUCCINO/MILK
(FROTHED MILK)
Making drinks with milk automatically
The CAFFELATTE, CAPPUCCINO, MACCHIATO and MILK buttons
on the control panel enable these drinks to be prepared
automatically.
Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
3. Press the button corresponding to the required drink.
The name of the drink selected is displayed together
with a progress bar which gradually fills as preparation
progresses.
4. After a few seconds, frothed milk is delivered from the
milk spout into the cup below. For drinks with coffee, the
machine automatically makes the coffee after delivering
the milk.
•
•
•
Programming the quantity of coffee and milk in the
cup for the CAFFELATTE, CAPPUCCINO, MACCHIATO and
MILK buttons.
The appliance is set by default to automatically deliver standard
quantities.
To change these quantities, proceed as follows:
1. Place a cup under the coffee and milk spouts.
2. Press and hold one of the function buttons until the
message “Milk for … Program Quantity” is displayed.
3. Release the button.
The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the button again.
5. The appliance stops delivering milk and (if required for
the drink being prepared) after a few seconds the coffee is
delivered into the cup. “Coffee for … Program Quantity”
is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the button.
Coffee delivery stops.
The machine is now reprogrammed with the new quantities
of milk and coffee.
Please note!
If during delivery you want to stop preparation, press the
corresponding button.
At the end of delivery, to increase the quantity of milk or
coffee in the cup, just press (within 3 seconds) the button
corresponding to the drink being made.
Do not leave the milk container out of the refrigerator
for long periods. The warmer the milk (5°C is ideal), the
poorer the quality of froth produced.
DELIVERING HOT WATER AND STEAM
Important! Danger of burns.
Never leave the machine unsupervised while delivering hot
water or steam.
The spout becomes hot during delivery. Hold by the handle
only.
Cleaning the milk frother with the CLEAN button
“Press CLEAN “ flashes on the display each time you use a milk
function.
To eliminate all milk residues, proceed as follows:
1. Leave the milk container in the machine (you do not need
to empty it);
2. Place a cup or other recipient under the frothed milk
spout.
3. Press the CLEAN button (fig. 23) and keep pressing until
the progress bar which appears on the display together
with the message “Cleaning underway” is complete.
•
Please note!
If “Energy Saving” mode is enabled, you may have to wait a few
seconds before the hot water or steam is delivered.
Delivering hot water
1. Make sure the hot water spout is attached correctly (fig.
6).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the
button (fig. 3).
“Hot water” is displayed, together with a progress bar
which fills gradually as preparation proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically.
To interrupt delivery of hot water manually, press the
button again.
Please note!
If you are making a number of milk based drinks one after
the other, you do not need to clean by pressing the CLEAN
button each time you make a cappuccino.
Just press it once after making the last cup (the appliance
continues functioning even if the CLEAN button is not
pressed).
Important!
After use, always clean the hot water/steam nozzle and the
milk container as described on page 14.
Change the quantity of water delivered automatically.
The machine is set by default to automatically delivery 250 ml
of hot water.
14
To modify these quantities, proceed as follows:
1. Position a container under the spout.
2. Press the
button again until “Hot water Program
quantity” is displayed, then release the
button.
3. When the hot water in the cup reaches the required level,
press the
button again.
The machine is now reprogrammed with the new quantity.
sponge and warm water.
6. Reinsert the nozzle and replace the cappuccino maker on
the nozzle, turning it and pushing it upwards until it is
attached.
Delivering steam
1. Make sure the hot water spout is attached correctly (fig.
6).
2. Fill a container with the liquid to be heated/frothed and
immerse the spout/cappuccino maker in the liquid.
3. Press the
button. After a few seconds, the steam to
heat the liquid comes out of the cappuccino maker;
4. When the required temperature is obtained, interrupt
steam delivery by pressing the
button again.
(You should not discharge steam for more than 3 minutes
at a time).
•
CLEANING
•
•
Important!
Do not use solvents, abrasive detergents or alcohol to
clean the coffee maker.
With De’Longhi bean to cup coffee makers, you need not
use chemical products to clean the machine.
None of the components can be washed in a dishwasher
apart from the milk container (C).
Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
Important!
Always stop steam delivery before extracting the container
containing the liquid to avoid burns from splashes.
Important! Danger of burns
If you make a number of cappuccinos one after the other, the
metal cup tray becomes hot.
Wait for it to cool down before touching it and handle it from
the front only.
Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially
skimmed milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow
movements in an upward direction.
• To avoid milk with poor froth or large bubbles, always
clean the spout as described in the following section.
To clean (with the machine on):
• Remove the drip tray (fig. 26), empty and clean.
• Empty the grounds container and clean thoroughly to
remove all residues left on the bottom. This can be done
with the spatula on the brush provided.
• Check the condensate tray (red) and empty if necessary.
Cleaning the spout after use
Always clean the spout after use to avoid the build-up of milk
residues and prevent the spout from clogging.
1. Place a container under the cappuccino maker and press
the
button to deliver a little water (fig. 3).
Stop the flow of water by pressing the
button
again.
2. Wait a few minutes for the cappuccino maker to cool
down, then extract the hot water spout.
Hold the spout with one hand and with the other, turn
the cappuccino maker anticlockwise (fig. 24) and pull it
downwards to remove it.
3. Also remove the steam nozzle by pulling it downwards
(fig. 25).
4. Check the hole shown by the arrow in fig. 25 is not
blocked. If necessary, clean with a pin.
5. Wash all parts of the cappuccino maker thoroughly with a
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog the
machine.
Cleaning the drip tray and condensate tray
Important!
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 27).
Before the indicator protrudes from the cup tray, the drip
tray must be emptied and cleaned, otherwise the water may
overflow the edge and damage the appliance, the surface it
rests on or the surrounding area.
15
To remove the drip tray:
1. Remove the drip tray and the grounds container (fig. 26);
2. Empty the drip tray and grounds container and wash
them;
3. Check the red condensate tray and empty if necessary.
4. Replace the drip tray and grounds container.
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 31).
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
Important!
RINSE WITH WATER ONLY
NO WASHING UP LIQUID - NO DISH WASHER
Clean the infuser without using washing up liquid as it
could be damaged.
6. Use the brush (D2) to remove any coffee residues left in
the infuser housing, visible through the infuser door.
7. After cleaning, replace the infuser by sliding it onto the
internal support; then push the PUSH symbol fully in until
it clicks into place.
Cleaning the inside of the coffee maker
Danger of electric shock!
Before cleaning internal parts, the machine must be turned
off (see “Turning off”) and unplugged from the mains power
supply.
Never immerse the coffee maker in water.
1. Check regularly (about once a month) that the inside of
the appliance (accessible after removing the drip tray) is
not dirty. If necessary, remove coffee deposits with the
brush provided or a sponge.
2. Remove the residues with a vacuum cleaner (fig. 28).
infuser support
Cleaning the water tank
1. Clean the water tank (A17) regularly (about once a month
and whenever you replace the water softener filter (if
provided) with a damp cloth and a little mild washing up
liquid.
2. Remove the filter (if present) and rinse with running water.
3. Replace the filter (if provided), fill the tank with fresh water
and replace the tank.
Please note!
If the infuser is difficult to insert, before insertion, adapt it to
the right size by pressing the two levers shown in the figure.
Large lever
Small lever
Cleaning the coffee spouts
1. Regularly clean the coffee spouts with a sponge or cloth
(fig. 29A).
2. Check the holes in the coffee spout are not blocked.
If necessary, remove coffee deposits with a toothpick (fig.
29B).
7. Once inserted, make sure the two red buttons have
snapped out.
PU
SH
Cleaning the pre-ground coffee funnel
Check regularly (about once a month ) that the pre-ground
coffee funnel (A6) is not blocked.
If necessary, remove coffee deposits with the brush (D2)
supplied.
Cleaning the infuser
The infuser (A9) must be cleaned at least once a month.
8. Close the infuser door.
9. Replace the water tank.
Important!
The infuser may not be extracted when the machine is on.
1. Make sure the machine is correctly turned off (see “Turning
the appliance off” on page 9).
2. Remove the water tank.
3. Open the infuser door (fig. 30) on the right side.
Cleaning the milk container
Clean the milk container as described below each time you
prepare milk:
1. Remove the lid.
16
DESCALE
2. Remove the milk spout and
intake tube.
3. Turn the froth adjustment
dial to the “INSERT” position
(see figure) and pull it off
upwards.
4. Wash all the components
thoroughly with hot water
and mild washing-up
liquid.
All components are
dishwasher safe, placing
them in the top basket of
the dishwasher.
Make sure there are no
milk residues in the hollow
and groove under the dial
(see figure alongside).
If necessary, scrape the
groove with a toothpick.
5. Rinse the inside of the froth
adjustment dial under
running water (see
figure)
6. Check that the intake
tube and spout are
not clogged with milk
residues.
7. Replace the dial (lining
up the arrow with the word
“INSERT”, the spout and the
milk intake tube.
8. Place the lid back on the milk
container.
Descale the machine when the message “DESCALE” flashes on
the display.
•
Important!
Descaler contains acids which may irritate the skin and
eyes.
It is vital to respect the manufacturer’s safety warnings
given on the descaler pack and the warnings relating to
the procedure to follow in the event of contact with the
skin and eyes.
Use De’Longhi descaler only.
Under no circumstances should you use sulphamic or acetic
based descalers. Their use invalidates the guarantee.
Failure to descale the appliance as described also
invalidates the guarantee.
1. Turn the machine on.
2. Press the MENU/ESC button to enter the menu.
3. Press the MILK or CAPPUCCINO button until “Descale” is
displayed.
4. Select by pressing the
button: “Descale
Confirm?” is displayed. Press
again to enable
the function.
5. The message “Add descaler Confirm?” is displayed
alternating with “EMPTY DRIP TRAY”
6. Completely empty the water tank (A17) and remove the
water filter (if present). Empty the drip tray (fig. 26) and
grounds container, then put back in the appliance.
7. Pour the descaler into the tank up to the level A
(corresponding to a 100 ml pack) marked on the side of
the tank (fig. 32), then add water (one litre) up to level B
(fig. 32). replace the water tank.
8. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout (fig. 6).
Important! Danger of burns
Hot water containing acid flows from the spout.
Avoid contact with splashes of water.
Cleaning the hot water/steam nozzle
Each time you prepare
milk, clean the nozzle
with a sponge to remove
milk residues from the
gaskets (see figure
alongside).
17
9. Press the
button to confirm introduction of the
solution.
The message “Descale underway “ is displayed.
The descaling programme starts and the descaler liquid
comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, the message “FILL TANK” is displayed.
7. The appliance is now ready for rinsing through with clean
water.
8. 9.
10.
11.
12.
Remove the water tank, empty, rinse under running
water, fill with clean water and replace.
“Rinsing... Confirm?” is displayed.
Empty the container used to collect the descaler solution
and replace it empty under the hot water spout.
Press the
button to start rinsing.
Hot water flows out of the spout and the message
“Rinsing...” is displayed.
When the water tank is completely empty, “ Rinsing
Complete Confirm?” is displayed.
Press the
button.
Insert the filter (if present) in the tank (see section
“Installing the filter” on page 18), fill the water tank again
and the appliance is ready for use.
5. Press the
button to confirm the setting.
6. Press the MENU/ESC button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting
WATER FILTER
Certain models are fitted with a water softener filter. If this
is not the case with your model, you are recommended to
purchase one from De’Longhi
33
Customer Experience.
To use the filter correctly,
follow the instructions
below.
Installing the filter
1. Remove the filter from
the packaging.
2. Turn the date indicator
disk (see fig. 33) until
the next 2 months of
use are displayed.
SETTING THE WATER HARDNESS
The DESCALE message is displayed after a period of time
according to water hardness.
The machine is factory set for a hardness value of 4.
The machine can also be programmed according to the
hardness of the mains water in the various regions so that the
machine needs to be descaled less often.
Please note
The filter lasts about two
months if the appliance is
used normally. If the coffee
maker is left unused with the
filter installed, it will last a
maximum of three weeks.
Measuring water hardness
1. Remove the “total hardness test” indicator paper attached
to this manual from its pack.
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly.
After about a minute, 1, 2, 3, or 4 red squares form,
depending on the hardness of the water. each square
corresponds to one level.
3. Remove the tank from
35A
the appliance and fill
with water.
4. Insert the filter in the
water tank and immerse
it completely for ten or
so seconds, sloping it to
enable the air bubbles
35B
to escape (fig. 34).
5. Insert the filter in the
filter housing (fig. 35A)
and press as far as it will
go.
6. Close the tank with the
lid (fig. 35B), then replace the tank in the machine.
When you install the filter, you must notify the appliance of its
presence.
7. Press the MENU/ESC button to enter the menu;
8. Press the MILK or CAPPUCCINO button (fig. 8) until
“Install filter” is displayed;
9. Press the
button;
soft water l
slightly hard water
ll
hard waterlll
very hard water
llll
Set water hardness
1. Press the MENU/ESC button to enter the menu.
2. Press the MILK or CAPPUCCINO button to select “Water
Hardness”.
3. Confirm the selection by pressing the
button.
4. Press the MILK or CAPPUCCINO button and set the
hardness shown by the indicator paper (see previous
section).
34
18
3. Press the MILK or CAPPUCCINO button (fig. 8) until
“Install filter Enabled” is displayed;
4. Press the
button
5. “Disable?” is displayed;
6. Press the
button to confirm and the MENU/ESC
button to exit the menu.
10. The message “Enable?” is displayed.
11. Press the
button to confirm the selection. “Hot
water Confirm?” is displayed.
12. Position a container with a minimum capacity of 100 ml
under the hot water spout.
13. Press the
button to confirm the selection. The
appliance begins delivering hot water and the message
“Please wait... “ is displayed.
14. After delivery, the appliance returns automatically to the
“Ready for coffee” position.
The new filter is active. You can now use the coffee maker.
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1450W
Pressure: 15 bar
Water tank capacity: 2.0 litres max.
Size Lxhxd: 238x350x445 mm
Cable length: 1.80 m
Weight: 11.8 kg
Beans container capacity: 250 g max.
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the filter:
1. Remove the exhausted filter;
2. Remove the new filter from the packaging.
3. Turn the date indicator disk (see fig. 33) until the next 2
months of use are displayed (the filter lasts about two
months);
4. Refill the tank;
5. Insert the filter in the water tank and immerse it
completely, tilting it to enable the air bubbles to escape
(fig. 34);
6. Place the filter in the filter housing (fig. 35aa) and press as
far as it will go. close the tank with the lid (fig. 35b), then
replace the tank in the machine;
7. Position a container with a minimum capacity of 100 ml
under the hot water spout.
8. Press the MENU/ESC button to enter the menu;
9. Press the MILK or CAPPUCCINO button until “Replace
filter “ is displayed.
10. Press the
button;
11. The message “Confirm?” is displayed.
12. Press the
button to confirm the selection;
13. “Hot water… Confirm?” is displayed.
14. Press the
button to confirm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
15. After delivery, the appliance returns automatically to the
“ready for coffee” position.
The new filter is now active and you can use the coffee maker.
The appliance complies with the following EC
directives:
•
•
•
•
Stand-by Directive no. 1275/2008;
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC directive 2004/108/EC and subsequent amendments
Materials and accessories coming into contact with food
conform to eec regulation 1935/2004.
DISPOSAL
Important information for correct disposal of the
product in accordance with EC Directive 2002/96/EC.
At the end of its working life, the product must not
be disposed of as urban waste. It must be taken to
a special local authority differentiated waste collection centre
or to a dealer providing this service. Disposing of a household
appliance separately avoids possible negative consequences
for the environment and health deriving from inappropriate
disposal and enables the constituent materials to be recovered
to obtain significant savings in energy and resources.As a
reminder of the need to dispose of household appliances
separately, the product is marked with a crossed-out wheeled
dustbin.
Removing the filter
If you want to continue using the appliance without a filter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted filter;
2. Press the MENU/ESC button to enter the menu;
19
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL TANK
Insufficient water in the tank.
Fill the tank with water and/or insert it correctly, pushing it
as far as it will go until it clicks into place.
EMPTY GROUNDS CONTAINER
The grounds container (A22) is full.
Empty the grounds container and drip tray, clean and replace
(fig. 26).
Important: when removing the drip tray, the grounds container must be emptied, even if it is not completely full.
If this is not done, when you make the next coffees, the
grounds container may fill up more than expected and clog
the machine.
GROUND TOO FINE ADJUST
MILL
alternating with...
Insert water spout and press
OK
The grinding is too fine and the coffee is delivered too slowly
or not at all.
Repeat coffee delivery and turn the grinding adjustment
dial (fig. 12) one click clockwise towards “7” while the coffee
mill is in operation.
If after making at least 2 coffees delivery is still too slow,
repeat the correction procedure, turning the grinding
adjustment dial another click (see the section “adjusting the
coffee mill” on page 12).
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has not been replaced
Remove the drip tray and insert the grounds container.
ADD PRE-GROUNDCOFFEE
The “pre-ground coffee” function has been selected without
placing any pre-ground coffee in the funnel.
Place pre-ground coffee in the funnel (fig. 17) or deselect
the “pre-ground” function.
DESCALE!
The machine must be descaled.
The descaling procedure described in the "descaling" section
(page 17) needs to be performed as soon as possible.
LESS COFFEE
Too much coffee has been used.
Select a milder taste by pressing the
button (fig.
9) or reduce the quantity of pre-ground coffee, if using the
pre-ground function.
FILL BEANS CONTAINER
The coffee beans have run out.
Fll the beans container (fig. 13).
The pre-ground coffee funnel is clogged.
Clear the funnel with the help of a brush as described in the
section “Cleaning the pre-ground coffee funnel”.
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after cleaning.
Insert the infuser as described in the section “cleaning the
infuser”.
INSERT TANK
The tank is not correctly in place.
Insert the tank correctly and press as far as it will go.
GENERAL ALARM
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described in
the section “cleaning and maintenance”.
If the message is still displayed after cleaning, contact
De’Longhi Customer Experience.
EMPTY CIRCUIT FILL CIRCUIT
alternating with
Hot water press OK
The water circuit is empty
Connect the water spout (D3) (fig.6) and press ok to deliver
water from it, until it flows out normally.
REPLACE FILTER
The water filter is exhausted.
Replace the filter or remove it as described in the section
“Water filter”.
Press CLEAN
Milk has been delivered recently and the tubes inside the
milk container must be cleaned.
Press the CLEAN button (fig. 23) and keep it pressed until the
progress bar which appears on the display together with the
message “Cleaning underway “ is complete.
INSERT WATER SPOUT
The hot water spout is not inserted or is inserted incorrectly.
Insert water spout (D3) as far as it will go.
INSERT MILK CONTAINER
The milk container is not inserted correctly.
Insert the milk container as far as it will go (fig. 21).
20
TROUBLESHOOTING
Below is a list of some of the possible malfunctions.
If the problem cannot be resolved as described, contact De’Longhi Customer Experience.
PROBLEM
POSSIBLE CAUSE
REMEDY
The coffee is not hot
The cups were not preheated.
•
•
Enable the cup warmer, leave the cups at least 20
minutes to warm up.
Warm the cups by rinsing them with hot water (N.B.
you can use the hot water function).
The infuser has cooled down because 2/3 minutes
have elapsed since the last coffee was made.
Before making the coffee, warm the infuser by using the
Rinsing function to perform a rinse cycle (page 10).
Low coffee temperature is set.
In the menu, set a higher coffee temperature.
The coffee is ground too coarsely.
Turn the grinding adjustment dial one click anticlockwise
towards “1” while the coffee mill is in operation (fig. 28).
Continue one click at a time until coffee delivery is satisfactory.
The effect is only visible after delivering 2 coffees (see the
section: “adjusting the coffee mill” on page 12).
The coffee is unsuitable.
Use pre-ground coffee for espresso coffee makers
The coffee is delivered too slowly or a
drop at a time.
The coffee is ground too finely.
Turn the grinding adjustment dial one click clockwise towards “7” while the coffee mill is in operation (fig. 28).
Continue one click at a time until coffee delivery is satisfactory. The effect is only visible after delivering two coffees.
(see the section “adjusting the coffee mill” on page 12).
Coffee does not come out of one of
the spouts.
The spouts are blocked.
Clean the spouts with a toothpick (fig. 29B).
The milk does not
come out of the milk
spout.
the milk container lid is dirty.
Clean the milk container lid as described in the section “cleaning the milk container”.
The milk contains
large bubbles and
squirts out of the
milk spout or there
is little froth .
the milk is not cold enough or is not semi-skimmed.
Use skimmed or semi-skimmed milk at refrigerator temperature (about 5° c).
If the result is not as you wished, try changing brand of
milk.
The froth adjustment dial is incorrectly adjusted.
Adjust following the instructions in the section “making
drinks with milk”.
The milk container lid or froth adjustment dial is
dirty
Clean the milk container lid and dial as described in the section “cleaning the milk container”.
The hot water/steam nozzle is dirty
Clean the nozzle as described in the section “cleaning the hot
water/steam nozzle”.
The spout is dirty.
Clean as described in the section “Cleaning the spout after
use”.
The connector is not inserted correctly.
Insert the connector as far as it will go in the socket at the
back of the appliance.
It is not plugged into the mains socket.
Plug into the mains socket.
The main switch (A7) is not turned on.
Place the main switch in the i position (fig. 2).
The appliance has not been turned off correctly
Turn the appliance off by pressing the
button (page 10)
and wait until the display is completely shut off. At this point
the infuser is in the correct position and can be extracted.
The coffee is thin or not creamy
enough.
The milk contains
large bubbles here
is little froth .
The appliance does not come on.
The infuser cannot be extracted
21
Электрочайники
Наборы кастрюль и
сковородок
Электро-керамические
обогреватели
Чайные и кофейные
сервизы
Кофемолки
Чайники заварочные
Чашки
Соковыжималки
Кухонные доски
Кофе
Чайники
Вазы
Скатерти и салфетки
Бытовая химия
Различные аксессуары
Коврики и подставки для
сервировки