Smeg Linea CMSC451 Kahve Makinası Kullanma - Smeg-TR

CONTENTS
Descaling................................................................................18
Changing coffee temperature.................................................19
Changing the length of time the appliance remains on . ........19
Setting water hardness ..........................................................19
Resetting default values (reset) .............................................19
Washing procedure.................................................................19
INTRODUCTION......................................................... 7
Symbols used in these instructions...........................................7
Letters in brackets.....................................................................7
Troubleshooting and repairs . ...................................................7
SAFETY..................................................................... 7
Fundamental safety warnings . ................................................7
Designated use.........................................................................8
Instructions...............................................................................8
CHANGING THE LANGUAGE....................................... 19
TURNING THE APPLIANCE OFF.................................. 19
TECHNICAL SPECIFICATION ...................................... 20
DESCRIPTION............................................................ 8
Description of the appliance . ...................................................8
Description of milk container and accessories ..........................8
Description of control panel......................................................8
DISPOSING OF THE APPLIANCE................................. 20
DISPLAYED MESSAGES ............................................. 21
TROUBLESHOOTING................................................. 22
RECIPES ................................................................. 23
PRELIMINARY CHECKS............................................... 8
Controls after transport ............................................................8
Installing the appliance............................................................8
Connecting the appliance.........................................................9
AUTOMATIC CUP TRAY LIGHT...................................... 9
BUILT-IN INSTALLATION........................................... 10
USING THE APPLIANCE FOR THE FIRST TIME . ............ 12
TURNING ON AND HEATING UP . ............................... 12
MAKING COFFEE USING COFFEE BEANS ..................... 12
CHANGING THE QUANTITY OF COFFEE IN THE CUP...... 13
AJUSTING THE COFFEE MILL ..................................... 14
MAKING ESPRESSO COFFEE WITH PRE-GROUND COFFEE
(INSTEAD OF BEANS) .............................................. 14
DELIVERING HOT WATER.......................................... 14
CHANGING THE QUANTITY OF HOT WATER................. 14
MAKING CAPUCCINO (FROTHED MILK AND COFFEE) ... 14
MAKING FROTHED MILK (WITHOUT COFFEE).............. 15
CHANGING THE QUANTITY OF COFFEE AND MILK FOR
CAPPUCCINO........................................................... 15
CLEANING AND MAINTENANCE................................. 16
Cleaning the coffee maker......................................................16
Cleaning the coffee grounds container....................................16
Cleaning the drip tray.............................................................16
Cleaning the water tank..........................................................16
Cleaning the spouts . ..............................................................16
Cleaning the pre-ground coffee funnel...................................16
Cleaning the inside of the coffee maker..................................16
Cleaning the infuser................................................................16
Cleaning the milk container....................................................17
CHANGING AND SETTING MENU PARAMETERS .......... 17
Setting the clock ....................................................................18
Setting auto-start time ..........................................................18
6
INTRODUCTION
SAFETY
Fundamental safety warnings
Thank you for choosing the automatic coffee and cappuccino
maker.
We hope you enjoy using your new appliance.
Take a few minutes to read these instructions.
This will avoid all risks and damage to the machine.
Important! The appliance is designed and produced
for domestic use only.
Danger! This is an electrical appliance and may cause
electric shock.
You should therefore respect the following safety warnings:
• Never touch the appliance with damp hands.
• Never touch the plug with damp hands.
• Make sure the socket used is freely accessible at all times,
enabling the appliance to be unplugged when necessary.
• If the appliance is faulty, do not attempt to repair.
Turn it off using the main switch (A19), unplug from the
mains socket and contact Customer Services.
• If the plug or power cable is damaged, it must be replaced
by customer services only to avoid all risk.
Symbols used in these instructions
Important warnings are identified by these symbols.
These warnings must absolutely be respected.
Failure to observe the instructions could result in electric shock,
serious injury, burns, fire or damage to the appliance.
Danger!
Failure to observe the warning could result in possibly life threatening injury from electric shock.
Important!
Failure to observe the warning could result in injury or damage
to the appliance.
Important! Keep all packaging (plastic bags, polystyrene foam) away from children.
Danger of burns!
Failure to observe the warning could result in scalds or burns.
Important! The appliance is not intended for use by
persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children must be supervised to ensure they do not play with the
appliance
N.B.:
This symbol identifies important advice or information for the
user.
Letters in brackets
The letters in brackets refer to the legend in the Description of
the Appliance on page 3.
Danger of burns! This appliance produces hot water
and steam may form while it is in operation.
Avoid contact with splashes of water or hot steam.
Avoid touching hot surfaces when the appliance is in use.
Troubleshooting and repairs
In the event of problems, first try and resolve them following
the information given in the sections “Displayed messages” and
“Troubleshooting”.
If this does not resolve the problem or you require further information, you should consult Customer Services by calling the
number given on the “Customer Service” sheet.
If your country is not among those listed on the sheet, call the
number given in the guarantee.
If repairs are required, contact Customer Services only.
The addresses are given in the guarantee certificate provided
with the machine.
Important! Do not grasp the coffee maker when it
is out of the cabinet. Do not rest recipients containing liquids
or inflammable or corrosive materials on top of the appliance.
Place the accessories required to prepare the coffee (the measure for example) in the special holder. Do not rest large objects
which could obstruct movement or unstable objects on the
appliance.
Important! Never make drinks, hot water or steam
when the appliance is extracted. Always make sure the appliance is inactive before extracting it. Failure to observe this precaution could lead to damage to the appliance.
7
Designated use
B2.
B3.
B4.
B5.
B6.
B7.
B8.
This appliance is designed and made to prepare coffee and heat
drinks.
All other use is considered improper.
This appliance is not suitable for commercial use.
The manufacturer is not liable for damage deriving from improper use of the appliance.
This appliance can be installed over a built-in oven if the latter
is fitted with a cooling fan at the rear (maximum oven power:
3 kW).
Milk container handle
CLEAN button
Milk intake tube
Frothed milk spout
Milk frother
Hot water spout
Measure
Description of control panel
(page 3 - C)
A number of buttons on the panel have a double function. This is
indicated in brackets in the description.
C1. Display: guides the user in using the appliance.
C2. MENU button to activate or deactivate menu parameter
setting mode
C3.
button to select pre-ground coffee
(When in the MENU: NEXT button to display the next menu
parameter).
C4. Rinse button
to perform a brief rinse to heat the infuser.
(When you access the MENU: “CHANGE” button to modify
menu parameters).
C5.
button to deliver hot water.
(When you access the MENU: OK button to confirm menu
parameters).
C6.
knob to turn the appliance on and off.
C7.
button to select the coffee taste
C8.
button to deliver one or two cups of short coffee
C9.
button to deliver one or two cups of standard coffee
C10. button to deliver one or two cups of long coffee
C11. knob to deliver cappuccino or frothed milk
Instructions
Read these instructions carefully before using the appliance.
• Keep these instructions. If the appliance is passed to other
persons, they must also be provided with these instructions.
• Failure to follow these instructions may result in burns or
damage to the appliance.
The manufacturer is not liable for damage deriving from
failure to respect these instructions.
DESCRIPTION
Description of the appliance
(page 3 - A )
A1. Cup tray
A2. Service door
A3. Coffee guide
A4. Coffee grounds container
A5. Infuser
A6. Lights
A7. Control panel
A8. Hot water and steam nozzle
A9. Water tank
A10.Coffee spout (adjustable height)
A11.Drip tray
A12.Bean container lid
A13.Container for coffee beans
A14.Grinding adjustment knob
A15.Pre-ground coffee funnel door
A16.Compartment for measure
A17.Pre-ground coffee funnel
A18.Power cable
A19.Main switch
A20. Tray
A21. IEC connector
PRELIMINARY CHECKS
Controls after transport
After removing the packaging, make sure the product is complete and undamaged and that all accessories are present.
Do not use the appliance if it is visibly damaged.
Contact Customer Services.
Installing the appliance
Important! When installing the appliance, respect the
following safety warnings:
• Installation must be performed by a qualified professional
in compliance with legislation in force in the country of
installation (see section: BUILT-IN INSTALLATION).
• The packing elements (plastic bags, polystyrene foam,
etc.) should be kept out of reach of children as they are a
safety hazard.
Description of milk container and accessories
(page 3 - B)
B1. Frothed milk regulator
8
•
•
Do not install the appliance in rooms where the temperature may drop to 0°C or lower (the water in the appliance
could freeze and cause damage).
You should customise the water hardness as soon as possible following the instructions in the “SETTING WATER
HARDNESS” section.
Connecting the appliance
Danger! Check that the mains power supply voltage
corresponds to the value indicated on the appliance rating plate.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified professional.
To comply with safety directives, an omnipolar switch with a
minimum contact distance of 3 mm must be installed.
Do not use multiple sockets or extensions.
To learn to use the appliance correctly, the first time you use it
follow the detailed instructions in the following sections.
Important! Safety cutout devices must be included
in the mains power supply in compliance with the installation
regulations in the country concerned.
AUTOMATIC CUP TRAY LIGHT
When the appliance is turned on, the lights (A6) automatically
light up the spout and cup tray.
The lights stay on until the appliance is turned off.
While coffee, steam or hot water is being delivered, the cooling
fan comes on.
At the end of the function, the cooling fan remains on to avoid
condensation forming inside the cabinet. After several minutes,
the fan goes off automatically.
N.B.: The appliance also completes this cycle if switched
off by turning the
knob (C6) to the right or left.
Important! Do not look at the lights directly or using
an optical instrument.
9
BUILT-IN INSTALLATION
mm
22
mm
2
2 mm
22
455
mm
mmmm
455
455
Verify the minimum measurements required for correct installation of the appliance.
The coffee maker must be installed in a column and the column
must be firmly fixed to the wall with commercially available
brackets.
Important:
• Important: all installation or maintenance operations must
be performed with the appliance disconnected from the
mains electricity supply.
• Kitchen furniture in direct contact with the appliance must
be heat resistant (65°C min).
• To guarantee correct ventilation, leave a gap at the bottom
of the cabinet (see measurements in figure).
372
mm
mmmm
372
372
595 m
595 mm
595 mm
m
m
m
15
m
m
15 mm
15
m
45 m
m
45 m
m
m
45
450
450450
850
850
850
mm
mmmm
mm
361 m
m
361 mm
361
45 mm
45 mm
45 mm
m
45 m
m
45 m
m
45 m
560 m
m
560 m
560 mm
m
528 m
m
528 m
528 mm
m
45 mm
45 mm
45 mm
m
45 m
m 45 mm
m
0
50 m 45 mm
m
Min.
500 mm
mm
.
500
550 m Minn.
i
m
550 mm M
550
45 mm
45 mm
45 mm
m
45 m
m
45 m
m
45 m
45 mm
45 mm
45 mm
200 cm2
200 cm2
200 cm2
10
200 cm2
200 cm2
200 cm2
xx16
2
x 16
x2
x 16
x 16
x4
x4
x4
x2
x4
x2
Position the rails on the sides of the cabinet as shown in the
figure.
Fix with the screws, then extract them completely.
If the coffee maker is installed over a warmer drawer (500 W
max.), use the top surface of this as a reference to position the
x1
rails. x 1
In this case, there will be no surface to rest the rails on.
Position the appliance on the rails, making sure the pins are
correctly inserted in the housings, then fix it with the screws
supplied. x 4
x4
560 +
1 mm
x4
x1
x1
560 +
1 mm
50mm
x. 3
appro
x.
appro
m
350m
x4
560 +
560 +
50mm
x. 3
appro
1 mm
1 mm
mm
x. 350
appro
Fix the power cable with the clip to avoid it tangling when the
appliance is inserted or extracted.
The power cable must be long enough to allow the appliance to
be extracted from the cabinet to fill the coffee beans container.
The appliance must be earthed in compliance with legislation.
Electrical connections must be performed by a qualified electrician in compliance with the manufacturer’s instructions and
legislation in force in the country of installation.
The electrical socket must be accessible.
If necessary, correct alignment of the appliance by positioning
the spacers supplied under or at the sides of the support.
11
USING THE APPLIANCE FOR THE FIRST TIME
right or left.
•
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
•
1.
2. 3. 4. 5. 6. Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the mill.
The machine is, however, guaranteed to be new.
You should customise water hardness as soon as possible
following the instructions in the “Setting water hardness”
section.
Connect the appliance to the mains electricity supply and
press the main switch (A19).
You must select the required language:
To set English, wait for the appliance to display “PRESS OK
TO INSTALL ENGLISH”. While the message is displayed, hold
the OK button (C5) (fig. 1) down for at least 3 seconds until “ENGLISH INSTALLED” is displayed. If you set the wrong
language by mistake, follow the instructions in the section
“Changing the language” to choose the right language.
Follow the instructions indicated by the appliance:
After 5 seconds, the appliance displays “FILL TANK”. To fill
the water tank, remove (fig. 2), rinse and fill with fresh
water without exceeding the MAX line.
Replace the tank and push as far as it will go.
Place a cup under the hot water spout (fig. 3).
(If the hot water spout is not inserted, the appliance displays “INSERT WATER SPOUT”. Attach it as shown in figure
4.
The appliance now displays: “HOT WATER PRESS OK”.
Press the OK button (C5) (fig. 1) and after a few seconds a
little water comes out of the spout.
(Delivery stops automatically).
The machine now displays “TURNING OFF... PLEASE WAIT”
and goes off.
Extract the appliance by pulling it out using the handles
(fig. 5). Open the lid and fill the container with coffee beans, then close the lid and push the appliance in.
TURNING ON AND HEATING UP
Danger of burns! During rinsing, a little hot water
flows from the coffee spouts. Avoid contact with splashes of
water.
To turn the appliance on, turn the knob (C6) to the right or
left (fig. 6). “HEATING UP... PLEASE WAIT” is displayed.
After heating, the message “RINSING” is displayed. As well as
heating the boiler, the appliance also heats the internal circuits
by circulating hot water.
The appliance is at temperature when the message “READY
STANDARD TASTE” is displayed.
MAKING COFFEE USING COFFEE BEANS
1. The appliance is preset to make coffee with a standard taste.
You can also choose coffee with an extra-mild, mild, strong
or extra-strong taste.
To choose the required taste, press the
button (C7)
(fig. 7). The required coffee taste is displayed.
2. Place 1 cup under the spouts to make 1 coffee (fig. 8) or 2
cups for 2 coffees (fig. 9).
Lower the spouts as near as possible to the cup for a creamier coffee (fig. 10).
3. Press the
button (C8) to make a short coffee (fig. 11),
the button (C9) for a standard coffee and the
button (C10) for a long coffee. To make 2 coffees, press the
button twice (within 2 seconds).
To change the quantity of coffee the appliance delivers
automatically into the cup, proceed as described in the
following section.
(The appliance now grinds the beans and starts delivering
the coffee into the cup. Once the set amount of coffee has
been delivered, the machine stops delivery automatically
and expels the exhausted coffee grounds into the grounds
container.
4. After a few seconds, the ready message is displayed again
and you can make another coffee.
5. To turn the appliance off, turn the
knob (C6) to the
right or left.
(Before going off, the appliance performs an automatic
rinse cycle (a little hot water flows from the spouts and is
Important! To prevent malfunction, never introduce
pre-ground coffee, freeze dried coffee, caramelised beans or
anything else which could damage the appliance.
The coffee maker is now ready for normal use.
N.B.: When using the appliance for the first time, you
need to make 4-5 cups of coffee and 4-5 cappuccinos before the
appliance starts to give satisfactory results.
N.B.: Each time you turn the coffee maker on by the
main switch (A19), it performs a SELF-DIAGNOSIS cycle and
then goes off. To turn it on again, turn the knob (C6) to the
12
collected in the drip tray beneath.
Take care to avoid scalds).
NOTE 1: If the coffee is delivered a drop at a time or not at all,
turn the grinding adjustment knob (fig. 12) one click clockwise
(see “Adjusting the coffee mill”).
Proceed one click at a time until coffee delivery is satisfactory.
NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory, turn the grinding adjustment knob (fig. 12) one click
anticlockwise (see “Adjusting the coffee mill”).
Avoid turning the grinding adjustment knob excessively otherwise when you select 2 cups, the coffee may be delivered a drop
at a time.
NOTE 3: Tips for a hotter coffee: • When you turn the appliance on, if you want to make a
short coffee (less than 60 cc), rinse the cups with hot water
to preheat the cups.
If more than 2/3 minutes have passed since the last coffee
was made, before requesting another coffee, you must
preheat the infuser by pressing the
button (C4) (fig.
13).
Deliver the water into the underlying drip tray or alternatively use this water to fill (and then empty) the cup to be
used for the coffee, so as to preheat it.
• Unless preheated, do not use excessively thick cups as they
will absorb too much heat.
• Preheat the cups by rinsing them with hot water.
NOTE 4: While the appliance is making coffee, delivery can be
interrupted at any moment by pressing the previously selected
button, (C8),
(C9) or (C10).
NOTE 5: As soon as delivery is finished, to increase the quantity
of coffee in the cup, just hold down the previously selected coffee button,
(C8),
(C9) or
(C10), until the required
amount is reached (this must be done within 3 seconds after
completion of delivery).
NOTE 6: When the appliance displays “FILL TANK”, fill the tank
with water or the appliance will not deliver coffee.
(It is normal for there to be a little water left in the tank when
the message is displayed).
NOTE 7: After about 14 single (or 7 double) coffees, the appliance displays “EMPTY GROUNDS CONTAINER”, indicating that the
grounds container is full and must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
When cleaning, always extract the drip tray completely to
avoid it falling when the grounds container is removed.
Empty the grounds container and clean thoroughly to remove
all residues left on the bottom.
Important! when removing the drip tray, the grounds
container MUST be emptied, even if it is not completely full. If
this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.
NOTE 8: Never extract the water tank while the machine is delivering coffee.
If it is removed, it will not be possible to make the coffee and
the appliance will display “GROUND TOO FINE ADJUST MILL and
INSERT WATER SPOUT AND PRESS OK”.
To use the appliance again, insert the hot water spout (fig. 4) if
not already in position, then press the OK button (C5) and deliver water from the spout for a few seconds.
CHANGING THE QUANTITY OF COFFEE IN THE CUP
The appliance is set by default to automatically make the following types of coffee:
• short coffee when the button (C8) is pressed;
• standard coffee when the
button (C9) is pressed;
• long coffee when the
button (C10) is pressed.
To change these quantities, proceed as follows:
• hold down the button corresponding to the quantity you
want to change,
(C8), or
(C9) or
(C10), for at
least 3 seconds then release until the message “PROGRAM
QUANTITY” is displayed and coffee delivery commences;
• when the coffee in the cup reaches the required level, press
the same button again to memorise the new amount.
The appliance is now reprogrammed with the new settings and
displays: “READY”.
To clean, open the service door on the front of the appliance by
pulling the handle (fig. 14), extract the drip tray (fig. 15), empty
and clean.
13
ADJUSTING THE COFFEE MILL
enable the coffee mill.
NOTE 1: Never introduce pre-ground coffee when the machine is
off or it could spread through the inside of the appliance.
NOTE 2: Never add more than 1 level measure, otherwise either
the appliance will not make the coffee and the pre-ground
coffee will be dispersed inside the appliance, dirtying it, or the
coffee will be delivered a drop at a time.
NOTE 3: Use the measure provided to add the right amount of
coffee.
NOTE 4: Introduce only pre-ground coffee for espresso coffee
machines into the funnel. Never fill with coffee beans, freeze
dried coffee or other substance that could damage the appliance.
NOTE 5: If more than one measure of pre-ground coffee is used
and the funnel clogs, push the coffee down with a knife (fig. 18)
then remove and clean the infuser and machine as described in
the “Cleaning the infuser” section.
The coffee mill is preset in the factory to make coffee correctly
and should not require adjusting initially.
However, if after making the first few coffees you find that delivery is either too fast or too slow (a drop at a time), this can be
corrected by adjusting the grinding adjustment knob (fig. 12).
Turn one click clockwise (one number) for more rapid coffee
delivery (not a drop at a time).
Turn one click anticlockwise for slower coffee delivery and a
creamier coffee. These adjustments will only be evident after at
least 2 cups of coffee have been delivered.
The grinding adjustment knob must only be turned when the
coffee mill is in operation.
DELIVERING HOT WATER
•
•
•
•
For slower delivery and creamier coffee, turn one click anticlockwise (finer pre-ground coffee).
For faster delivery (not a drop at a time), turn one click clockwise
(coarser pre-ground coffee).
(Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the
mill. It is, however, guaranteed to be new.)
CHANGING THE QUANTITY OF HOT WATER
MAKING ESPRESSO COFFEE WITH PRE-GROUND
COFFEE (INSTEAD OF BEANS)
•
•
•
•
Always make sure the appliance is ready.
Make sure the hot water spout is in place (fig. 4);
Position a container under the spout (fig. 3).
Press the
button (C5) (fig. 1).
The message “HOT WATER” is displayed and hot water flows
out of the hot water spout into the container.
(You should not deliver hot water for more than 2 minutes
at a time).
To interrupt the flow, press the
button (C5).
Once the set quantity of hot water has been reached, delivery stops automatically.
The appliance is set by default to automatically deliver about
200 ml of hot water.
To change these quantities, proceed as follows:
• Attach the hot water spout (fig. 4).
• Position a container under the spout (fig. 3).
• Hold the
button (C5) down for at least 2 seconds then
release it. The message “HOT WATER PROGRAM QUANTITY” is displayed and hot water flows out of the hot water
spout.
• When the hot water in the cup reaches the required level,
press the
button (C5) to memorise the new amount.
(You should not deliver hot water for more than 2 minutes
at a time).
Press the button (C3) (fig. 16) to select the preground coffee function. This disables the coffee mill function.
The appliance now displays the message: “READY PREGROUND”.
Extract the machine by pulling it outwards using the handles.
Lift the central lid, place one measure of pre-ground coffee
in the funnel (fig. 17), push the appliance in then proceed
as described in the section “Making coffee using coffee beans”.
N.B.: You can make just one coffee at a time by pressing the
(C8),
(C9) or (C10) button once only.
After using the machine with pre-ground coffee, to go back
to making coffee using beans, deactivate the pre-ground
coffee function by pressing the
button (C7) again to
MAKING CAPPUCCINO (FROTHED MILK AND COFFEE)
•
14
Select the taste of the coffee you want to use to make the
•
•
•
•
ast 3 seconds (fig. 25). The appliance displays “CLEANING”.
After cleaning, remove the milk container and place in the
refrigerator.
The milk should not be left out of the refrigerator for more
than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk the
appliance delivers automatically into the cup, proceed as described in the section “Changing the quantity of coffee and milk for
cappuccino”.
cappuccino by pressing the
button (C7).
Remove the lid of the milk container.
Fill the container with about 100 grams of milk for each
cappuccino to be prepared (fig. 19). Never exceed the MAX
level (corresponding to about 750 ml) marked on the jug.
You should ideally use skimmed or semi-skimmed milk at
refrigerator temperature (about 5°C).
Make sure the intake tube is correctly inserted in the rubber washer (fig. 20) then replace the milk container lid.
Position the frothed milk regulator (B1) between the
words CAPPUCCINO and CAFFELATTE printed on the milk
container lid.
The quality of froth can be adjusted by moving the frothed
milk regulator towards the word CAFFELATTE for a denser
froth.
Moving it towards the word CAPPUCCINO obtains a less
dense froth.
MAKING FROTHED MILK (WITHOUT COFFEE)
•
•
•
•
•
•
NO schiuma
Schiuma
“più compatta”
•
Cursore
Schiuma “meno densa”
Remove the lid of the milk container.
Fill the container with the quantity of milk you want to
prepare (fig. 19).
Replace the lid on the milk container.
Attach the milk container to the appliance (fig. 22).
Place a sufficiently large cup under the spout (fig. 23).
Turn the
knob (C11) to the left.
“FROTHED MILK” is displayed and after a few seconds, frothed milk flows out of the milk spout into the cup below.
After delivery, clean the tubes inside the milk container
by pressing the CLEAN button as described in the previous
section (note 3).
CHANGING THE QUANTITY OF COFFEE AND MILK
FOR CAPPUCCINO
•
Remove the hot water spout (fig 21) and attach the milk
container to the nozzle (fig. 22).
• Position the milk tube as shown in fig. 23 and then place a
sufficiently large cup under the coffee and milk spouts.
• Turn the knob (C11) to the right.
“CAPPUCCINO...” is displayed and after a few seconds, frothed milk flows out of the milk spout into the cup below.
(Delivery stops automatically).
• The appliance then grinds the beans, delivers the coffee
and displays the “ready” message again.
• The cappuccino is now ready. Sweeten to taste and, if desired, sprinkle the froth with a little cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or
coffee can be interrupted by turning the knob (C11) to the
right.
NOTE 2: If the milk in the container finishes while delivering frothed milk, remove the container and add milk.
Then re-attach it and turn the
knob (C11) to the right to
request cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the
milk frother, always clean the circuits in the milk container lid
after making cappuccino
• Place a recipient under the milk spout;
• Press the CLEAN button on the lid and hold down for at le-
The appliance is set by default to automatically deliver a standard cappuccino.
To change these quantities, proceed as follows:
• Fill the container with milk up to the maximum level indicated on the container.
• Turn the
knob (C11) to the right and keep it turned for
at least 3 seconds until “MILK FOR CAPPUCCINO PROGRAM
QUANTITY” is displayed. Release the knob. The appliance starts delivering milk.
• Once the required quantity of milk has been delivered, turn
the knob (C11) to the right again. Milk delivery stops.
(You should not deliver frothed milk for more than 3 minutes at a time.)
• After a few seconds, the appliance delivers coffee into the
cup and displays “COFFEE FOR CAPPUCC. PROGRAM QUANTITY”.
• Once the required quantity of coffee has been delivered,
turn the
knob (C11) to the right again. Coffee delivery
stops.
The appliance is now re-programmed with the new settings and
displays: READY.
15
Before performing any cleaning operations, leave the machine
to cool down completely and unplug from the mains power supply. Never immerse the coffee maker in water. It is an electrical
appliance. Do not use solvents or abrasive detergents to clean
the coffee maker. A soft damp cloth will suffice. Never wash any
of the components of the coffee maker in the dishwasher.
CLEANING AND MAINTENANCE
1. Open the service door (A2) (fig. 14).
2. Remove the drip tray (A11) and the grounds container (A4)
(fig. 15).
3. Empty the drip tray and grounds container and wash
them.
4. Replace the drip tray complete with grounds container.
5. Close the service door.
Cleaning the coffee maker
Cleaning the water tank
1. Clean the water tank (A9) regularly (about once a month)
with a damp cloth and a little mild washing up liquid.
2. Clean to remove all washing up liquid residues, then rinse
the water tank thoroughly.
The following parts of the machine must be cleaned regularly:
• Coffee grounds container (A4).
• Drip tray (A11).
• Water tank (A9).
• Coffee spouts (A10).
• Pre-ground coffee funnel (A17).
• Inside of the machine, accessible after opening the service
door (A2).
• Infuser (A5).
Cleaning the spouts
1. Clean the coffee spout nozzles (A10) periodically using a
sponge or cloth (fig. 27).
2. Check regularly that the holes in the coffee spout are not
blocked.
If necessary, remove coffee deposits with a toothpick (fig.
26).
Cleaning the coffee grounds container
When “EMPTY GROUNDS CONTAINER” is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
To clean:
• Open the service door (A2) on the front of the appliance
(fig. 14), extract the drip tray (A11) (fig. 15), empty and
clean.
• Empty the grounds container and clean thoroughly to remove all residues left on the bottom.
Cleaning the pre-ground coffee funnel
•
Check regularly (about once a month ) that the pre-ground
coffee funnel (A17) is not blocked.
If necessary, remove coffee deposits with a knife (fig. 18).
Danger! Before performing any cleaning operations,
the machine must be turned off by pressing the main switch
(A19) and unplugged from the mains power supply. Never immerse the coffee maker in water.
Important! When removing the drip tray, the grounds
container must be emptied, even if it is not completely full. If
this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.
Cleaning the inside of the coffee maker
1. Check regularly (about once a week) that the inside of the
appliance is not dirty.
If necessary, remove coffee deposits with a knife and a
sponge.
2. Remove the residues with a vacuum cleaner (fig. 30).
Cleaning the drip tray
Cleaning the infuser
Important! If the drip tray is not emptied regularly, the water could overflow from the edge and seep inside or
around the coffee maker. This could damage the appliance and
cabinet.
The infuser (A5) must be cleaned at least once a month.
Important! The infuser (A5) must not be removed
when the appliance is on. Do not attempt to use force to remove
the infuser as this could damage the coffee maker.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 31).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the tray:
1. Make sure the machine is correctly turned off (see “Turning
the appliance off”).
2. Open the service door (A2) (fig. 14).
16
Cleaning the milk container
3. Remove the drip tray (A11) and grounds container (fig.
15).
4. Press the two red release buttons inwards and at the same
time pull the infuser outwards (fig. 28).
Important! Always clean the tubes inside the milk
container (B) when you prepare milk. If there is still milk in the
container, do not leave it out of the refrigerator for longer than
strictly necessary. Clean the container each time you prepare
milk as described in Note 3 in the section “Making cappuccino”.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout and intake tube.
Important! Do not use washing up liquid to clean the
infuser. It would remove the lubricant applied to the inside of
the piston, causing the infuser to seize up and become unusable.
5. Soak the infuser in water for about 5 minutes, then rinse
under the tap.
6. After cleaning, replace the infuser (A5) by sliding it onto
the internal support and pin at the bottom;
Spout
Milk intake tube
Support
Groove
Frothed milk regulator
Pin
then push the PUSH symbol fully in until it clicks into place.
Hole
N.B.: If the infuser is difficult to insert, you must first
adapt it to the right dimensions by pressing it forcefully from the
bottom and top as shown in the figure.
Hole
3. Remove the frothed milk regulator by pulling it outwards.
4. Wash all the components thoroughly with hot water and
mild washing-up liquid.
Make sure there are no milk residues left inside the holes
and the groove on the fine end of the frothed milk regulator.
5. Check that the intake tube and spout are not clogged with
milk residues.
6. Replace the frothed milk regulator, milk spout and intake
tube.
7. Replace the milk container lid.
7. Once inserted, make sure the two red buttons have snapped out.
8. Replace the drip tray (A11) and grounds container.
9. Close the service door (A2).
CHANGING AND SETTING MENU PARAMETERS
17
After turning the knob (C6) to the right or left and waiting
for the appliance to be ready, you can use the internal menu to
modify the following parameters and functions:
• CLOCK
• ON 7:30
• AUTO-START NO
•
•
•
•
•
DESCALE NO
TEMPERATURE MEDIUM
OFF AFTER 1 HOUR
WATER HARDNESS 4
DEFAULT VALUES NO
relating to the procedure to follow in the event of contact with
the skin and eyes.
N:B:: Use the descaler recommended by the manufacturer only. Use of other descalers invalidates the guarantee.
Failure to descale the appliance as described also invalidates the
guarantee.
Setting the clock
To set the clock, proceed as follows:
• Press the MENU button (C2) (the light over the button comes on) then press the NEXT button (C3) repeatedly until
the appliance displays: “CLOCK… 00:00”.
• Press the CHANGE button (C4) to set the clock.
(If you hold the CHANGE button (C4) down, the time is
changed rapidly).
• Press the OK button (C5) to confirm.
• Press the MENU button (C2) to exit programming mode or
NEXT (C3) to change other parameters.
Over time, constant heating up of the water used to make the
coffee leads to limescale building up in the inner circuits of the
appliance.
When “DESCALE” is displayed, the machine requires descaling.
Proceed as follows:
• press the MENU button (C2) (the light over the button comes on) then press the NEXT (C3) button repeatedly until
the appliance displays “DESCALE NO”;
• press the CHANGE button (C4) and the appliance displays
“DESCALE YES”
• press the OK button (C5) to start the descale programme;
• empty the water tank, pour the contents of the descaler
bottle into the tank respecting the instructions given on
the descaler pack, then add water up to the MAX level
marked on the water tank.
When descaling subsequently, use descaler of the same
type and brand as supplied (available from the manufacturer’s authorised Customer Services) or a descaler recommended by Customer Services. Always follow the instructions on the pack.
• attach the hot water spout to the nozzle;
• place a container with a minimum capacity of 1.5 litres
under the hot water spout (fig. 3);
• press the OK button (C5). Descaler flows out of the hot water spout into the container below.
“APPLIANCE IN DESCALE” is displayed;
• the descale programme automatically performs a series of
deliveries and pauses to remove limescale deposits from
inside the machine.
• After about 30 minutes, the appliance displays “RINSING
FILL TANK”.
The appliance must now be rinsed through to eliminate residues
of descaling solution from inside the appliance. Proceed as follows:
• Empty the water tank, rinse and fill with clean water.
• Replace the tank;
• Empty the full container and put back under the hot water
spout;
• Press the OK button (C5). Hot water flows out of the spout
into the container below and the appliance displays “RINSING”;
• When the water tank is empty, the appliance displays the
Setting auto-start time
This function programmes the time the machine will come on
automatically to be ready for use.
• Make sure the clock on the appliance is set as described in
the previous section.
• Press the MENU button (C2) (the light over the button comes on) then press the NEXT button (C3) repeatedly until
the appliance displays: “START TIME… 00:00”.
• Press the CHANGE button (C4) to set the auto-start time.
(If you hold the CHANGE button (C4) down, the time is
changed rapidly).
• Press the OK button to confirm the value;
• Press the NEXT button (C3) once and the appliance displays
the message: “AUTO-START NO”.
Press the CHANGE button (C4) to modify the function (the
machine displays “AUTO-START YES”).
• Press the OK button (C5) to activate auto-start;
NOTE: when the machine is off and an auto-start time has been
set, the
symbol appears alongside the time on the unlit
display.
• Press the MENU button (C2) to exit programming mode or
NEXT (C3) to change other parameters.
Descaling
Important! Before descaling, make sure the water
softener filter has been removed.
Important! Descaler contains acids which may irritate the skin and eyes. It is vital to respect the manufacturer’s
safety warnings given on the descaler pack and the warnings
18
message “RINSING COMPLETE... PRESS OK”;
Press the OK button (C5) and refill the water tank with clean water.
• The descale programme is now terminated and the appliance is ready to make coffee again.
NOTE: If descaling is interrupted before completion, the machine still displays the descaling message and the process must be
begun again from the beginning.
Empty the water tank, rinse with clean water and deliver a cup
of hot water.
Proceed as follows:
• remove the “Total Hardness Test” strip (attached to page 2)
from its packaging then dip it fully in the water for a few
seconds,
Then remove and wait about 30 seconds (until it changes
colour and forms red squares).
• switch the machine on by turning the knob (C6) to the
right or left (fig. 6);
• press the MENU button (C2) then press the NEXT button (C3) repeatedly until the appliance displays “WATER
HARDNESS 4”;
• press the CHANGE button (C4) repeatedly until the number
coincides with the number of red squares on the test strip
(for example, if there are 3 red squares on the test strip,
press the button until “WATER HARDNESS 3” is displayed).
• press the OK button (C5) to confirm.
The coffee maker is now programmed to provide the descale warning when necessary based on the actual hardness
of the water.
•
Important! FAILURE TO DESCALE THE APPLIANCE REGULARLY INVALIDATES THE GUARANTEE.
Changing coffee temperature
To change coffee temperature, proceed as follows:
• press the MENU button (C2) (the light over the button comes on) then press the NEXT button (C3) repeatedly until
the appliance displays “TEMPERATURE HIGH...”;
• press the CHANGE button (C4) until the appliance displays
the required coffee temperature;
• press the OK button (C5) to confirm the temperature selected;
• Press the MENU button (C2) to exit programming mode or
NEXT (C3) to change other parameters.
Resetting default values (reset)
If you change the original values, the default values can be reset
as follows:
• Press the MENU button (C2) then press the NEXT button
(C3) repeatedly until the appliance displays “RESET TO DEFAULT NO”;
• press the CHANGE button (C4) and the appliance displays
“RESET TO DEFAULT YES”;
• press the OK button (C5) to reset the default values;
• The appliance is now reset to the default settings and the
“READY” message is displayed.
Changing the length of time the appliance remains
on
The appliance is set by default to go off automatically 1 hour
after the last coffee has been made.
To increase the number of hours the machine stays on (max. 3),
proceed as follows:
• Press the MENU button (C2) (the light over the button comes on) then press the NEXT button (C3) repeatedly until
the appliance displays “OFF AFTER 1 HOUR”.
• Press the CHANGE button (C4) to change the number of
hours the appliance remains on.
• Press the OK button (C5) to confirm.
• Press the MENU button (C2) to exit programming mode or
NEXT (C3) to change other parameters.
Washing procedure
This function is available to customer services personnel only.
CHANGING THE LANGUAGE
To change the language, press the CHANGE button (C4) for at
least 5 seconds until the appliance displays the installation message in various languages.
Select the required language as described in the section “Using
the appliance for the first time”.
Setting water hardness
TURNING THE APPLIANCE OFF
The descale message is displayed after the appliance has been
operated for a factory set period of time calculated on the basis
of the maximum quantity of limescale which may be contained
in the water used.
The operating period can be extended if required, making descaling less frequent by programming the machine on the basis
of the real lime content in the water used.
Each time the appliance is turned off, it performs an automatic
rinse cycle which cannot be interrupted.
Danger of burns! During rinsing, a little hot water
flows from the coffee spouts. Avoid contact with splashes of
water.
19
base of the plug.
B) If your appliance is not fitted with a plug, please follow the
instructins provided below:
WARNING - THIS APPLIANCE MUST BE EARTHED
important
The wires in the mains lead are coloured in accordance with the
following code:
Green and yellow:
Earth
Blue:
Neutral
Brown:
Live
To turn the appliance off, turn the knob (C6).
The appliance performs the rinse cycle then goes off.
N.B.: If the appliance is not used for an extended period,
place the main switch (A19) on the back of the appliance in the
0 position.
TECHNICAL SPECIFICATION
Voltage: 220-240 V~ 50/60 Hz max. 10A
Absorbed power: 1350W
Pressure: 15 bars
Water tank capacity: 1.7 litres
Size LxHxD: 595 x 455 x 412 mm
Weight: 26 kg
•
•
As the colours of the wires in the mains lead may not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The green and yellow wire must be connected to the terminal
in the plug marked with the letter E or the earth symbol
or
coloured green or green and yellow.
The blue wire must be connected to the terminal marked with
the letter N or coloured black.
The brown wire must be co
The appliance complies with the following EC directives:
Low Voltage Directive 2006/95/EC and subsequent
amendments;
EMC Directive 2004/108/EC and subsequent amendments
Materials and accessories coming into contact with food conform to European regulation (EC) no. 1935/2004.
Disposing of the appliance
In compliance with European directive 2002/96/EC, the appliance must not be disposed of with household waste, but taken to
an authorised waste separation and recycling centre.
electrical connection (UK only)
A) If your appliance comes fitted with a plug, it will incorporate a 13 Amp fuse. If it does not fit your socket, the plug
should be cut off from the mains lead, and an appropriate
plug fitted, as below.
WARNING: Very carefully dispose of the cut off plug after
removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard.
With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a
moulded-on type, the fuse cover must be re-fitted when
changing the fuse using a 13 Amp Asta approved fuse to
BS 1362. In the event of losing the fuse cover, the plug
must NOT be used until a replacement fuse cover can be
obtained from your nearest electrical dealer. The colour of
the correct replacement fuse cover is that as marked on the
20
DISPLAYED MESSAGES
DISPLAYED MESSAGE
POSSIBLE CAUSE
REMEDY
FILL TANK
The water tank is empty or positioned Fill the tank with water and/or insert it
incorrectly.
correctly, pushing it as far as it will go.
GROUND TOO FINE ADJUST MILL
Insert water spout and press OK (C5)
The grinding is too fine and the coffee is
delivered too slowly.
The machine cannot make coffee as there
is air in the hydraulic circuit.
INSERT WATER SPOUT
The hot water spout is not inserted or is Insert the hot water spout as far as it will
inserted incorrectly.
go.
INSERT GROUNDS CONTAINER
The grounds container (A4) is too full or
more than 3 days have passed since you
last made coffee (this guarantees correct
hygiene of the machine).
INSERT GROUNDS CONTAINER
After cleaning, the grounds container has Open the service door and insert the
not been replaced.
grounds container.
INSERT MILK CONTAINER
The milk container is not inserted.
ADD PRE-GROUND COFFEE
With the pre-ground function selected, Extract the appliance and place prepre-ground coffee has not been poured ground coffee in the funnel.
into the funnel.
The funnel (A17) is blocked.
Empty the funnel with the help of a knife,
as described in the section “Cleaning the
pre-ground coffee funnel”.
DESCALE!
The machine must be descaled.
The descaling procedure described in the
“Descaling” section needs to be performed as soon as possible.
LESS COFFEE
Too much coffee has been used
Select a milder taste or reduce the quantity of pre-ground coffee, then make the
coffee again
FILL BEANS CONTAINER
The coffee beans have run out.
Fill beans container
INSERT INFUSER ASSEMBLY
The infuser has not been replaced after Insert the infuser as described in the seccleaning.
tion “Cleaning the infuser”.
CLOSE DOOR
The service door is open
Close the service door.
GENERAL ALARM!
The inside of the appliance is very dirty.
Clean the inside of the appliance thoroughly, as described in the section “Cleaning
and maintenance”.
If the message is still displayed after cleaning, contact a customer services.
21
Turn the grinding adjustment knob one
click clockwise towards “7”.
Insert the hot water spout, press the OK
button (C5) and deliver water from the
spout for a few seconds.
Empty the grounds container and clean,
then replace.
Important: when removing the drip tray,
the grounds container MUST be emptied,
even if it is not completely full.
If this is not done, when you make the
next coffees, the grounds container may
fill up more than expected and clog the
machine.
Insert the milk container as far as it will
go.
TROUBLESHOOTING
If the problem cannot be resolved as described, contact Customer Services.
Below is a list of some of the possible malfunctions.
PROBLEM
POSSIBLE CAUSE
The coffee is not hot.
The cups were not preheated.
The coffee is not creamy enough .
The coffee is ground too coarsely.
REMEDY
Heat the cups by rinsing them in hot water or leaving them to rest for at least 20
minutes on the cup warmer tray.
The infuser has cooled down because 2/3 Before making coffee, heat the infuser by
minutes have elapsed since the last cof- pressing the
button (C4).
fee was made.
Wrong type of coffee
Turn the grinding adjustment knob one
click anticlockwise towards “1” while the
coffee mill is in operation.
Use a type of coffee for espresso coffee
makers.
The coffee is delivered too slowly or a The coffee is ground too finely.
drop at a time.
Turn the grinding adjustment knob one
click clockwise towards the 7 while the
coffee mill is in operation.
Continue one click at a time until coffee
delivery is satisfactory.
The effect is only visible after delivering
two coffees.
The coffee is delivered too quickly.
Turn the grinding adjustment knob one
click anticlockwise towards “1” while the
coffee mill is in operation.
Avoid turning the grinding adjustment
knob excessively otherwise when you
select 2 cups, the coffee may be delivered
a drop at a time.
The effect is only visible after delivering
two coffees.
The coffee is ground too coarsely.
Coffee does not come out of one of the The spouts are blocked.
spouts.
Clean the spouts with a toothpick (fig.
26).
The coffee does not come out of the The holes in the spouts are clogged with
spouts, but from around the service door dry coffee dust.
(A2).
The coffee guide (A3) inside the service
door is blocked and cannot swing.
If necessary, remove coffee deposits
with a toothpick, sponge or stiff bristled
kitchen brush.
Thoroughly clean the coffee guide (A3),
particularly near the hinges.
Water comes out of the spouts instead of The pre-ground coffee may be blocked in Clean the funnel (A17) with a wooden
coffee.
the funnel (A17).
or plastic fork, clean the inside of the
appliance.
The milk does not come out of the milk The intake tube is not inserted or is inser- Insert the intake tube (B4) in the rubber
spout (B5).
ted incorrectly.
washer in the milk container lid (fig. 20).
The milk is not well frothed.
The milk container lid is dirty.
Clean the milk container lid as described
in the section “Cleaning the milk container”.
The frothed milk regulator is not positio- Adjust following the instructions in the
ned correctly.
section “Making cappuccino”.
22
PROBLEM
POSSIBLE CAUSE
REMEDY
The milk contains bubbles or squirts out The milk is not cold enough or is not You should ideally use skimmed or semiof the milk spout.
semi-skimmed.
skimmed milk at refrigerator temperature (about 5°C). If the result is still disappointing, try another brand of milk.
The frothed milk regulator is incorrectly Move the frothed milk regulator slightly
adjusted.
towards the word “CAFFELATTE” (see section “Making cappuccino”).
The milk container lid is dirty.
Clean the milk container lid as described
in the section “Cleaning the milk container”.
RECIPES
Coffee punch
Irish cofee
Ingredients (serves 3):
2 spoons of sugar
1 spoon of water
9 teaspoons of whipping cream
6 spoon of Irish Whisky
4 cups of hot coffee
Method: Boil the water and the sugar for approximately one minute then add to the Whiskey and the hot coffee. Mix and pour
into stem glasses. Carefully pour the cream onto the coffee (3
teaspoons per glass).
RECIPE TIP: lightly whip the cream so that it stays on top of the
coffee. Grand Marnier or Calvados can also be added.
Ingredients (serves 6):
1/2 l of hot coffee
1/2 l of white Port
1/2 l of rum
100 g of candied brown sugar
Method: Pour the coffee into a pot, add the rum and the Port
and heat until it reaches boiling point. Gradually add the candied sugar, tasting now and then until sufficiently sweet. When
the sugar has dissolved serve in traditional, short stemmed
glasses.
Emperor’s coffee
Coffee sorbet
Ingredients (serves 3):
3 espresso coffees
3 egg yolks
3 teaspoons of sugar
3 dl of milk
2 small glasses of brandy
Method: Beat the egg yolks with the sugar and the brandy.
Add hot milk and hot coffee.
RECIPE TIP: lightly whip the milk and add slowly at the very last
ingredient. Best served accompanied by a chocolate cake.
Ingredients (serves 4):
200 g of granulated sugar
2 dl of espresso coffee
Method: Combine ½ l of water and the sugar to make a syrup
and simmer for a few minutes; allow it to cool then mix in the
coffee. Filter as soon as a smooth mixture is obtained then place
in the freezer to set, mixing often until of a grainy consistency.
Iced coffee
Ingredients:
4 espresso coffees
4 teaspoons of sugar
12 ice cubes
Method: Crush the ice and add to the pre-sugared coffee.
Shake in a shaker until a frothy, creamy mixture
is obtained.
RECIPE TIPS: blend on a low blender setting and
serve in a flute or glass tumbler.
Danish coffee
Ingredients:
6 eggs
grated rind of one lemon
100 g of sugar
3/4 l strong, cold coffee
1 large glass of brandy
Method: Beat the eggs and the lemon rind, and then add the
sugar a little at a time until the eggs become light and airy.
Slowly add the coffee and the brandy, stirring constantly. Serve
in chilled teacups or “Ballon” glasses.
23
2
A6 A7
A
A3
A4
A8 A9
A5
A15
A2
A10
A11
A1
A12
A16
A13
A14
A17
A18
A21
A19
A20
B
B1
B6
B3
B8
B7
B5
B4
B2
C
C1
C6
C2
C3
C4
3
C5
C7
C8
C9 C10
C11
2
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
4
1
2
17
18
19
20
21
22
23
24
25
26
27
29
30
31
5
28