Keurig® Vue™ V1255 Brewer Use &

Keurig® Vue™ V1255 Brewer
Use & Care Guide
IMPORTANT SAFEGUARDS
Safe Operation & Use
When using electrical appliances, basic safety precautions should
be followed, including the following:
1.Read all instructions before using.
2.Do not touch hot surfaces. Use
handles and knobs when available.
3.This appliance must be properly
installed and located in accordance
with these instructions before it
is used.
4.The use of accessory attachments
not recommended by the appliance
manufacturer may result in fire,
electrical shock or injury to persons.
5.Do not place on or near a hot gas or
electric burner, or in a heated oven.
6.Do not use outdoors.
7.To protect against fire, electric shock
and injury do not immerse cords,
plugs, or the appliance in water or
any other liquid.
8.Do not overfill the Water Reservoir
with water.
9.Use only water in this appliance!
Do not put any other liquids or
foods in the Water Reservoir
except as instructed in the Cleaning
Instructions in this guide.
13.Do not let the cord hang over the edge
of the table or counter, or touch hot
surfaces.
14.To disconnect, press the Power
Button on the Brewer to ‘OFF’ status
and then remove the plug from the
wall outlet.
15.Close supervision is necessary when
any appliance is used by or near
children.
16.Do not lift the Handle to open the
Brewer while brewing is in progress.
17.Always keep the Water Reservoir Lid
on the Water Reservoir unless you are
refilling it.
18.This appliance is equipped with a
power cord having a grounding wire
with a grounding plug. The appliance
must be grounded using a 3-hole
properly grounded outlet. In the
event of an electrical short circuit,
grounding reduces the risk
of electrical shock.
19.If the outlet is a standard 2-prong
wall outlet, it is your personal
responsibility and obligation to have
it replaced with a properly grounded
10.Turn off and unplug the Brewer before
3-prong wall outlet.
cleaning or maintenance. Allow to cool
before putting on or taking off parts
20.Do not, under any circumstances,
and before cleaning the appliance.
cut or remove the third (ground)
prong from the power cord or use
11.For best operation, plug the appliance
an adapter.
into its own electrical outlet on a
dedicated circuit to prevent flickering 21.Consult a qualified electrician if
of lights, blowing of fuses or tripping
the grounding instructions are not
a circuit breaker.
completely understood, or if doubt
exists as to whether the appliance
12.Do not operate any appliance with a
is properly grounded.
damaged cord or plug or after the
appliance malfunctions or is damaged
22.Do not use the appliance for
in any manner. Contact Keurig
other than its intended use.
Customer Service to report any
malfunction of or damage to the Brewer.
2
CAUTION: There is extremely hot water in the Vue™pack Holder during
the brew process. To avoid risk of injury, do not lift the Handle or
remove the Brew Head during the brewing process. Do not remove or
puncture the lid of the Vue™ pack prior to brewing. After brewing, use
caution when removing the Vue™ pack, as it will be hot.
Please always keep the Brewer in its upright position to avoid potential
injury and/or damage to your Brewer.
SHORT CORD INSTRUCTIONS: A short power supply cord is provided to
reduce the risk of becoming entangled in or tripping over a longer cord.
Longer detachable power-supply or extension cords are available and
may be used if care is exercised in their use.
If an extension cord is used, (1) the marked electrical rating of the cord
set or extension cord should be at least as great as the electrical rating
of the appliance; (2) the cord should be arranged so that it will not drape
over the counter top or tabletop where it can be pulled on by children or
tripped over unintentionally; and (3) the extension cord must include a
3-prong grounding plug.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
Save These Instructions.
WARNING
THIS PRODUCT CONTAINS CHEMICALS, INCLUDING
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
RISK OF FIRE OR
ELECTRIC SHOCK
DO NOT OPEN
!
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM
COVER. NO USER SERVICEABLE PARTS ARE
INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED
SERVICE PERSONNEL ONLY.
WARNING TO USERS AND PARENTS: DO NOT permit children to use
Brewer unless there is adult supervision. Brewer dispenses very hot water.
3
Table of Contents
Section 1 Brewer Overview
6
Section 2 Preparing Your Brewer
8
Section 3 Using Your Brewer
9
Section 4 Setting the Time & Temperature
17
Section 5 Caring for Your Brewer
20
Section 6 Recycling Vue™ Pack’s Plastic Cup
22
Section 7 Troubleshooting
23
Section 8 Warranty
24
Record Your Brewer Serial Number Above
The serial number can be found on the bottom of the Brewer
box and on the left side of the Brewer once the Water Reservoir
has been removed. Removing the serial number label from the
Brewer will void warranty.
4
5
SECTION 1
Brewer Overview
B
A
A “BREW” Button
Flashing indicates Brewer is ready to brew
B Power Button
Coffee
& Tea
Brew
Over Ice
Café
2 Step
C Touchscreen
Frothing
Not
Ready to Enjoy!
Brewing
PM
J
Coffee
Step2
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
Menu
Size
C
De-Scale Add Water
Set Clock
Set Auto Off Set
Set On Off Time Set
Set Brew Temp Set
D Handle
E Brew Head
D
F Power Cord
G Drip Tray
H Drip Tray Plate
E
I
I Water Reservoir
J Water Reservoir Flip Top Lid
F
G
H
The Keurig® Vue™ Brewer is not for
use with K-Cup® packs.
6
7
SECTION 2
SECTION 3
Preparing Your Brewer
Step 1
Step 1
Remove all adhesive tape from Brewer and label from
Touchscreen.
Brew what you love, the way you love it.
Plug cord into grounded outlet.
The Keurig® Vue™ V1255 commercial grade brewer is a completely new brewing
system that gives you total control to brew what you love, the way you love it.
If Brewer has been exposed to temperatures below freezing, allow
Brewer at least two hours to reach room temperature before
brewing. A frozen or extremely cold Brewer will not operate.
Step 2
Carefully remove Water Reservoir Lid. Remove the Water
Reservoir by lifting up and away from the Brewer.
Rinse Water Reservoir with fresh water. Return Water
Reservoir to Brewer. Fill the Water Reservoir to the
“MAX FILL” line. Bottled or filtered water is recommended.
Place Lid on Water Reservoir.
Step 2
Using Your Brewer
The V1255 features Custom Brew Technology™, which ensures that while you’re in
the office, your beverage is brewed to perfection the way it was designed, every
time. The Vue™ brewing system also allows you total control to brew your way:
stronger, bigger, hotter, and with more choices than ever before.
So what are you in the mood for today?
How to use the Vue™ Brewer Touchscreen
See page 16 for options for how to add water to the
Water Reservoir.
Step 3
Place a 10 oz. mug in the center of the Drip Tray and press
the Power Button.
The Brewer Handle should be in the lowered position.
Beverage
Category
Coffee
& Tea
Beverage Type
Café
2 Step
Activated
Brew Status
Not
Ready to
Brew
OZ
Coffee
Step 3
Brew
Over Ice
Step2
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
Menu
Size
Beverage Size Selection
Available Sizes
Coffee Tea/Other Hot Cocoa 4 - 18 oz.
6 - 12 oz.
6 - 10 oz.
Step 4
When the Brewer is first turned on, the Touchscreen
will indicate “Not Ready” as the Brewer heats the water.
Wait until the Touchscreen indicates “Ready”
(about four minutes).
Step 4
8
Strength Selection
(Coffee Only)
If there is not enough water in the Water Reservoir,
the Touchscreen will indicate “Add Water” and the Water
Reservoir light will flash.
Lift the Brewer handle and remove the shipping disk.
Lower the Brewer Handle, press the Coffee & Tea button,
then press the flashing “BREW” Button. Your Brewer will
dispense 8 oz. of hot water into your mug. Once complete,
discard the hot water. You are ready for your first brew!
The screen above shows all possible menu selections for illustration purposes only.
When in use, your Touchscreen will display only selectable actions.
9
SECTION 3
SECTION 3
Using Your Brewer
Using Your Brewer
Brewing Coffee, Tea,
Hot Cocoa and Hot Apple Cider
Choose Vue™ Pack
Make sure your Vue™ pack
features the Coffee & Tea Icon.
Lift the Brewer Handle, insert
the Vue™pack into the Holder
and lower the Brewer Handle.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Brew
Frothing
Enjoy!
H
Tea
Other
Froth
Step2
Step1
Regular
Hot
Cocoa
Café
Coffee
& Tea
Brew
Over Ice
Café
Coffee
Step2
2 Step
OZ M
PM
Menu
Size
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
OZ M
PM
Menu
Size
For large brew sizes, we recommend using Travel Mug
Vue™ packs, which are designed to deliver a great tasting
large mug-sized brew.
Follow the instructions for brewing a coffee (refer to page 10),
but select one of the larger size options (12 oz. to 18 oz.).
Note that Travel Mug beverages have been optimized at
14 oz. and 16 oz. settings. Enjoy your large mug brew!
After you lower the Brewer Handle, the screen will display as
pictured.
Once selected, the screen will display as pictured with the
“Coffee,” “Tea/Other” and “Hot Cocoa” buttons. Choose your
selected beverage.
To make coffee, choose your strength and size. If you prefer a
stronger brew, select “Strong.” Then select your beverage size
by using the + and - buttons.
4 - 18 oz.
6 - 12 oz.
6 - 10 oz.
12
14
16
18
12oz
14oz
16oz
18oz
oz
oz
oz
oz
12oz
14oz
16oz
18oz
oz
4oz
6oz
8oz
10oz
For hot cider, select “Tea/Other.” Select your beverage size
using the + and - buttons.
Available Sizes
Coffee Tea/Other Hot Cocoa If needed, remove the Drip Tray to allow your mug to fit.
To make coffee, tea, hot cocoa or other beverages, such as hot
cider, press the “Coffee & Tea” button.
Frothing
Not
Ready to Enjoy!
Brew
H
Coffee
Select Beverage Type & Size
For Large Mugs
4oz
6oz
8oz
10oz
oz
oz
oz
Available Sizes
Press BREW & Enjoy!
Do not remove mug or lift the Brewer Handle until “Enjoy” disappears
from Touchscreen. Remove the Vue™ pack after brewing is complete.
The Vue™ pack will be HOT after brewing. Use caution when
removing. Allow it to cool completely before handling.
Immediately after using a hot cocoa pack, we recommend running
a cleansing brew to avoid clogging. See page 15 for directions.
10
11
6oz
6oz
SECTION 3
SECTION 3
Using Your Brewer
Using Your Brewer
Brewing Café Beverages
Requires 2 Vue™ packs
1
Step 1
Step 2
Choose Café Step 1
Vue™ Pack
Choose Café Step 2
Vue™ Pack
Make sure your Vue™ pack
features the Café Icon.
Lift the Brewer Handle, insert
the Vue™ pack into the Holder
and lower the Brewer Handle.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Frothing
Not
Ready to Enjoy!
Brew
H
Coffee
Step2
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
Insert the Vue™ pack into
the Holder and lower the
Brewer Handle.
Select Café
Select Beverage Type & Size
Press the “Café” button, then the Touchscreen will display as
pictured. Froth is available in the 4 oz. brew size only.
After you insert the second Vue™ pack and lower
the Brewer Handle, the Touchscreen will display
as pictured.
OZ M
PM
Menu
Size
2
Coffee: For a coffee-based café beverage, press the “Coffee
Step 2” button. “Strong” is the default setting for café
beverages. Select regular if desired.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Activated
Frothing
Not
Ready to Enjoy!
Brew
Brewing
H
Coffee
Step2
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
4oz
6oz
OZ M
OZ
PM
Menu
Size
8oz
Add Water
Water
De-Scale Add
Set Clock
Set Auto Off Set
Set On Off Time Set
Set Brew Temp Set
Tea: For a tea-based café beverage, press “Tea/Other
Step 2” button.
Select your café beverage size using the + and - buttons.
The amount you select will be ADDED to the existing 4 oz.
of froth.
Press BREW
After the froth is prepared, lift the Brewer Handle and
carefully remove the pack. Proceed to Step 2.
1
The Vue™ pack will be HOT after brewing. Use caution when
removing. Allow it to cool completely before handling.
4oz
6oz
8oz
Available Sizes
If a selection is not made within 60 seconds, the Brewer will
return to the default screen. To complete the brew successfully,
follow the brewing instructions on page 10 and brew
“Coffee” 4 oz. “Strong” (for a coffee-based café beverage) or
“Tea/Other” 4 oz. (for a tea-based café beverage).
Press BREW & Enjoy!
Do not remove mug or lift the Brewer Handle until “Enjoy!”
disappears from Touchscreen.
Remove the Vue™ pack after brewing is complete.
12
The Vue™ pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
13
SECTION 3
SECTION 3
Using Your Brewer
Brewing Over Ice
Prepare Your Cup
Fill a 16 oz. plastic cup with ice. Do not use glass. Remove
the Drip Tray if necessary and place cup under the Brew head.
Choose Vue™ Pack
Make sure your Vue™ pack
features the Brew Over Ice Icon.
Lift the Brewer Handle, insert
the Vue™ pack into the Holder
and lower the Brewer Handle.
Brew
Over Ice
Café
2 Step
H
Coffee
Regular
Strong
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
Select Beverage Type & Size
Frothing
Not
Ready to Enjoy!
Brew
OZ M
PM
Menu
Size
Brew
Over Ice
Café
Coffee
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
2 Step
Frothing
Not
Ready to Enjoy!
Brew
H
Step2
Regular
Strong
Brew
Over Ice
Café
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
2 Step
Frothing
Not
Ready to Enjoy!
Brew
H
OZ M
PM
Menu
Size
Coffee
Regular
Strong
Brew
Over Ice
Café
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
2 Step
OZ M
PM
Menu
Size
the lid and any filter which adheres to it. Ensure
the empty Vue™ pack cup is clean.
* Available sizes for Iced Coffee and Iced Tea/Other
are 6 oz., 8 oz. and 10 oz.
Available Sizes*
Press BREW & Enjoy!
Do not remove mug or lift the Brewer Handle until “Enjoy”
disappears from Touchscreen.
Remove the Vue™ pack after brewing is complete.
The Vue™ pack will be HOT after brewing. Use caution when
removing. Allow it to cool completely before handling.
Step 1
Step 2 Place the EMPTY Vue™ pack cup in the Brewer and
place a mug on the Drip Tray.
Step 3 Lower the Handle, press the Coffee & Tea button
and press “BREW.” The Brewer will dispense 8 oz. of
hot water into your mug. Once complete, discard
the water and carefully remove the Vue™ pack cup.
The cleansing is complete.
Stopping the Brewing Process
If you need to stop the brewing process after it has started,
press and release the Power Button to turn the Brewer off.
The beverage flow will stop and the Brewer will shut off.
To turn the Brewer back on, place an empty mug on the
Drip Tray and press the Power Button. Since the previous
brew was interrupted, some water may drip into the mug
during preheating.
* Available sizes for Iced Café are 6 oz. and 8 oz.
14
Step 1 Take a used Vue™ pack and peel off the lid. Discard
Select the desired beverage type.
OZ M
PM
Menu
Size
After brewing certain Vue™ pack varieties such as hot
cocoa, iced tea or a café beverage, we recommend
performing a cleansing brew as follows:
The Vue™pack will be hot after brewing. Use caution when
removing. Allow it to cool completely before handling.
Frothing
Not
Ready to Enjoy!
Brew
H
What is a Cleansing Brew?
Select the “Brew Over Ice” button. The Touchscreen
will display as pictured.
Select your beverage size using the + and - buttons.
Coffee
& Tea
Using Your Brewer
We recommend that you perform a cleansing brew before
brewing your next beverage (see above). If this is not done,
the Brewer may deliver an additional amount of water for
your next beverage.
Step 2
Step 3
Dispensing Hot Water
If you need hot water for cooking (instant soup or oatmeal,
for example), place a cup or bowl below the Brew Head and
on the center of the Drip Tray. Lift and lower the Handle
WITHOUT inserting a Vue™ pack. Select “Coffee” (do not
select “Strong”) and press “BREW.” The Brewer will dispense
hot water into your cup or bowl.
15
SECTION 3
SECTION 4
Using Your Brewer
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Frothing
Not
Ready to Enjoy!
Brew
H
Coffee
Step2
Tea
Other
Step2
OZ M
PM
Menu
Size
Froth
Step1
Add Water
Regular
Strong
Hot
Cocoa
Café
Setting the Time & Temperature
Adding Water
Accessing the Settings Menu
When the water supply is low, the Touchscreen will display as
pictured and the light inside the Water Reservoir will flash.
The menu screen appears when the Brewer is first turned
on, the handle is raised, or when a brew has been completed.
Follow the steps below to access the settings menu. Press and
hold the “Menu” button to access. Use “Menu” button to tab
through the setting options.
Bottled or filtered water is recommended.
When brewing at sizes larger than 12 oz., if the Brewer senses the
water level is low, the brewing process will stop until the Water
Reservoir is refilled. Once enough water has been added, the
brewing process will resume.
Do not remove the Water Reservoir during the brewing process.
There are three options for filling the Water Reservoir:
Setting the Clock
Step 1
Select the “Menu” icon on the Touchscreen.
Coffee
& Tea
Remove the Water Reservoir Lid and pour water directly
into the Water Reservoir. Replace the Lid.
Step 2
The “H” will flash, indicating you are programming the
hours. The clock is on a 12h setting and will switch to PM
once the 12h mark is passed. Use the + and – buttons to
change the hours. Press the menu button again to set the
minutes. Use the + and – buttons to set the minutes.
Café
2 Step
Froth
Step2
Step1
Regular
Hot
Cocoa
Café
Coffee
& Tea
Brew
Over Ice
Option 2
Option 3
You may also remove the Water Reservoir from
the Brewer to fill it. Replace the Lid and return
the filled Water Reservoir to the Brewer.
Do not remove the Water Reservoir during the brewing process.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Frothing
Not
Ready to Enjoy!
Brewing
H
Coffee
Step2
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
OZ M
PM
Menu
Size
Add Water
Regular
Strong
16
If the Brewer senses the water level is low when brewing 14 oz.,
16 oz. or 18 oz. sizes, the brewing process will stop until the Water
Reservoir is refilled. Once enough water has been added, the
brewing process will resume. Ensure that your mug is still
on the Drip Tray.
You can program the Brewer to automatically turn off after
a certain period of time after the last brew. This feature can
be used as an energy saver.
In “Auto Off” programming mode, use the + and - buttons
to change the hours the Brewer will remain on after the last
brew. For example, if you select “2,” the Brewer will turn off
two hours after the last brew. Use the + and - buttons to
scroll to “Off” to deactivate the “Auto Off” feature.
Frothing
Enjoy!
Brew
H
Tea
Other
Froth
Step2
Step1
Regular
Hot
Cocoa
Café
Coffee
& Tea
Brew
Over Ice
Coffee
Step2
Instead of removing the Water Reservoir Lid, you can
lift the Flip Top. Pour water into the Water Reservoir.
Lower the Flip Top.
Programming the “Auto Off”
Feature
OZ M
PM
Menu
Size
Café
2 Step
Once the clock is set, press the “Menu” button to save your
settings. The screen will move to the next programmable
setting (Auto Off).
Frothing
Not
Ready to Enjoy!
Brew
H
Tea
Other
Coffee
Step2
Option 1
Brew
Over Ice
OZ M
PM
Menu
Size
Set Clock
Café
2 Step
H
Menu
Set Auto Off
Once the feature is set, press the “Menu” button to save your
settings. The screen will move to the next programmable
setting (Set On Time see page 18).
17
SECTION 4
SECTION 4
Setting the Time & Temperature
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Brew
Frothing
Enjoy!
H
Coffee
Step2
Regular
Tea
Other
Step2
Hot
Cocoa
Froth
Step1
Café
OZ M
PM
Menu
Size
Set
On Time
Programming the
“On Time” Feature
By programming the Brewer to turn on each day, you will
never have to wait for the Brewer to warm up to brew the
first cup. It takes the Brewer approximately four minutes
to warm up from room temperature.
The clock must be set in order for the “Auto Off ”, “On Time” and
“Off Time” features to operate correctly. See page 17 for directions.
If power is interrupted to the Brewer by unplugging it, or if power
is lost, follow the procedure on page 17 to set the clock.
In “On Time” programming mode, the “H” will flash,
indicating you are programming the hours. The clock is
on a 12h setting and will switch to PM once the 12h mark is
passed. Use the + and – buttons to set the hours. Press the
“Menu” button again to access the minutes. Use the + and buttons to set the minutes.
Once the “On Time” clock is set, press the “Menu” button
to save your settings. The screen will move to the next
programmable setting (Set Off Time).
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Brew
Frothing
Enjoy!
H
Coffee
Step2
Regular
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
OZ M
PM
Menu
Size
Set
Off Time
Programming the
“Off Time” Feature
Programming the “Off Time” will ensure the Brewer turns off
when it will not be used.
Setting the Time & Temperature
Setting the Brew Temperature
The Brewer has a preset temperature of 193° F. You can
adjust the temperature up or down in 1° increments within
the Brewer range (187° – 198° F). Once set, your beverages
will be brewed at the selected temperature.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Brew
Frothing
Enjoy!
H
Coffee
Step2
Regular
At high altitudes, it is possible for boiling to occur. In the
event this does happen, you can lower the temperature
using the instructions below.
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
OZ M
Menu
Size
Set Brew Temp Set
Here is how to set the brew temperature:
Step 1
In “Set Brew Temp” Mode, Use the + and – buttons to
change the temperature.
Step 2
Press the “Menu” button to save your setting and return
to the main screen.
Viewing Your Presets
Your settings will appear in the main menu. To review your
current settings, touch the “Menu” button. You can change
the settings at any time. Simply enter through the “Menu”
to reset any options using the directions in this section.
Coffee
& Tea
Brew
Over Ice
Café
2 Step
Brew
Frothing
Enjoy!
H
Coffee
Step2
Regular
Tea
Other
Froth
Step2
Step1
Hot
Cocoa
Café
OZ M
PM
Menu
Size
The clock must be set in order to program the “Auto Off ”, “On
Time” and “Off Time” features. See page 17 for directions.
In “Off Time” programming mode, the “H” will flash,
indicating you are programming the hours. The clock is
on a 12h setting and will switch to PM once the 12h mark is
passed. Use the + and – buttons to set the hours. Press the
“Menu” button again to access the minutes. Use the
+ and – buttons to set the minutes.
Once the “Off Time” clock is set, press the “Menu” button
to save your settings. The screen will move to the next
programmable setting (Setting the Brew Temperature).
18
19
SECTION 5
SECTION 5
Caring For Your Brewer
Cleaning & Maintenance
Cleaning External Parts
Cleaning of the Brewer’s external parts is recommended
one to two times per month. Never immerse the Brewer
in water or other liquids. The Housing and other external
parts may be cleaned with a soapy, damp, non-abrasive
cloth.
The Drip Tray can accumulate up to 13 oz. of overflow.
The Drip Tray and Drip Tray Plate should be periodically
inspected and rinsed clean. To remove the Drip Tray, simply
slide it toward you, keeping it level at all times to avoid
spilling. The Drip Tray and Drip Tray Plate should be cleaned
with a soapy, damp, non-abrasive cloth. The Drip Tray and
Drip Tray Plate should not be put in the dishwasher.
1
2
3
De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the mineral content
of the water in your area, calcium deposits or scale may build up in your Brewer. Scale
is non-toxic, but left unattended, it can hinder Brewer performance. De-scaling your
Brewer helps maintain the heating system and other internal parts of the Brewer that
come in contact with water.
The Brewer should be de-scaled every three to six months to ensure optimal
performance. It is possible for calcium deposits to build up faster, making it necessary
to de-scale more often.
The de-scale process requires the Brewer to stand for at least 4 hours. During this period, the
Brewer should not be used to brew beverages.
Prepare
Cleaning The Brew HEAD
Step 1 Lift the Brewer Handle.
Step 2 Grip and press the buttons on both sides of
the Brew Head and tilt it down.
Step 3 Pull the Brew Head toward you to remove.
Step 1 To begin, you will need:
• At least 48 oz. of undiluted white vinegar
• A large ceramic mug, at least 10 oz. (do not use a paper cup)
• A clean, empty Vue™ pack cup
Step 2 Empty the water in the Water Reservoir.
Step 3 Disable “Auto Off” and “On/Off Time” settings (refer to pages 17 and 18).
Carefully clean the Brew Head with a soapy, damp,
non-abrasive cloth and rinse thoroughly. The Brew
Head should not be placed in the dishwasher.
Fill & Clean
Return the Brew Head by sliding it gently back into place
until you hear a click. Lower the Brewer Handle and you are
ready to brew again.
Cleaning the Water Reservoir &
Water Reservoir Lid
The Water Reservoir and Lid should not be put
into the dishwasher. Clean them with a damp, soapy,
non-abrasive cloth and rinse thoroughly. Do not dry
the inside of the Water Reservoir with a cloth as lint
may remain.
CAUTION: Rinse the Water Reservoir thoroughly after cleaning
to ensure that no cleaners or cleaning solutions remain in this area
as they may contaminate the water supply in the Brewer.
20
Caring For Your Brewer
Step 1 Pour at least 48 oz. of the vinegar into the Water Reservoir.
Step 2 Place the mug on the Drip Tray Plate. Lift the Handle and insert a clean, EMPTY
Vue™ pack cup (refer to page 15, step 1). Lower the Handle, then press “BREW.” The
Brewer will dispense 8 oz. of hot vinegar into your mug. Dispose of the vinegar.
Step 3 Repeat the process until “Please Add Water” is indicated.
Step 4 Let the Brewer stand for at least 4 hours while still on.
Step 5 Discard the remaining vinegar from the Water Reservoir and rinse the Reservoir
thoroughly. Remove the empty Vue™ pack from the Brewer.
Rinse
Step 1 Ensure the Water Reservoir is filled with fresh water.
Step 2 Place a large mug on the Drip Tray Plate and run a cleansing brew. Pour the
contents of the large mug into the sink.
Step 3 Repeat the cleansing brew process until “Please Add Water” is indicated.
Step 4 You may need to perform additional cleansing brew cycles (refer to page 15)
if you notice any residual taste.
21
SECTION 6
SECTION 7
Recycling Vue Pack’s Plastic Cup
Troubleshooting
™
SITUATION SOLUTION
Recycle your Vue™ pack’s plastic cup wherever #5
plastic is accepted. #5 plastic may not be recyclable in
your community today, so please check locally with
your municipality or waste hauler, or visit
www.vuerecycling.com for more information about
recycling your Vue™ pack’s plastic cup.
Simply follow these simple steps:
Step 1
Once brewing is complete, lift the Brewer Handle and
carefully remove the Vue™ pack by holding the outer rim.
The Vue™ pack will be hot after brewing. Use
caution when removing. Allow it to cool completely
before handling.
Step 2
Once cool, separate the lid and filter from the cup.
The filter will adhere to the lid.
Step 3
Once separated, discard the lid and the attached filter.
Recycle your Vue™ pack’s plastic cup wherever #5
plastic is accepted.
Brewer does not • Make sure that the Power Button has been turned on and
have power
Touchscreen is illuminated.
• Plug Brewer into an independent outlet.
• Check to be sure that it is plugged in securely.
• Plug into a different outlet.
• Reset the circuit breaker if necessary.
Brewer will • After placing the Vue™ pack in the Vue™ pack Holder, make
not brew
sure the Handle is pushed down securely and the Touchscreen
displays the beverage options. Push the flashing “BREW”
Button.
• If the Touchscreen indicates “Please Add Water,” add water
to the Water Reservoir and make sure the Water Reservoir is
seated properly in its base.
• If the Touchscreen indicates “Please Add Water” even after
refilling, contact Customer Service at 1.866.901.BREW (2739).
• The Brew Head may need to be cleaned or the Brewer may need
to be de-scaled (refer to pages 20 and 21).
Brewer brews only • Clean the Brew Head if necessary (refer to page 20).
a partial cup • T
he Water Reservoir may have been removed during brewing.
Replace the Water Reservoir and perform cleansing brews
(refer to page 15) without a Vue™ pack.
• De-scale the Brewer (refer to page 21).
• If you have repeated the de-scale procedure on your Brewer
two times and it is still only brewing a partial cup, contact
Customer Service at 1.866.901.BREW (2739).
Brewer shuts • Check to make sure that the “On/Off Time” and/or “Auto Off”
off or turns on
settings have not been set. Please refer to pages 17 and 18 for
automatically
instructions.
Water Reservoir • The water level is low and a full cup cannot be brewed.
light is flashing and
Add water to Water Reservoir.
the Touchscreen • If the water level is not low, remove the Water Reservoir and
indicates “Add Water” empty the water. Then thoroughly clean (refer to page 20). Fill
the Water Reservoir to the “MAX FILL” line and then return it to
the Brewer and ensure it is seated properly in its base. Wait for
the Water Reservoir light to stop flashing.
The Time is not displayed • If power is interrupted to the Brewer by unplugging it, or if
on the Touchscreen
power is lost, follow the procedure on page 17 to set the clock.
22
23
SECTION 8
SECTION 8
Warranty
Limited One Year Warranty
Keurig warrants that your Brewer will be free of defects in materials or workmanship
under normal use for one year from the date of purchase. It is recommended that you
fill out and return the warranty card enclosed with your Brewer so that your purchase
information will be stored in our system. Keurig will, at its option, repair or replace
the Brewer without charge upon its receipt of proof of the date of purchase. If a
replacement Brewer is necessary to service this warranty, the replacement Brewer
may be new or reconditioned. If a replacement Brewer is sent, a new limited one year
warranty will be applied to the replacement Brewer.
This warranty only applies to Brewers operated in the United States and Canada. This
warranty gives you specific legal rights, and you may also have other rights that vary
from state to state and, in the case of Canada, from province to province.
Only the use of Keurig Brewed® VueTM brand packs and accessories will guarantee the
proper functioning and lifetime of your Keurig® Brewer. Any damage to or malfunction
of your Brewer resulting from the use of non Keurig Brewed® VueTM brand packs and
accessories may not be covered by this warranty or may result in a service fee if the
damage or malfunction is determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES
SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS
AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF
FORESEEABLE. Some states or provinces do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitation or exclusion may not
apply to you depending on the state or province of purchase.
Nor does this warranty cover damages caused by use of non Keurig Brewed® VueTM
brand packs or accessories, services performed by anyone other than Keurig or its
authorized service providers, use of parts other than genuine Keurig parts, or external
causes such as abuse, misuse, inappropriate power supply or acts of God.
Other Limitations
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS WARRANTY,
WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY
DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR V1255 BREWER,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE. Some states or provinces do not allow disclaimers of such
implied warranties or limitations on how long an implied warranty lasts, so the above
limitation may not apply to you depending on the state or the province of purchase.
How do you obtain warranty service?
Keurig® Brewers are high-quality appliances and, with proper care, are intended
to provide years of satisfying performance. However, should the need arise for
warranty servicing, simply call Keurig Customer Service at our toll free phone number
1.866.901.BREW (2739). Please do not return your Brewer for servicing without first
speaking to Keurig Customer Service to obtain an Authorization to Return number
(ATR). Keurig® Brewers returned without an ATR number will be returned to the sender
without servicing.
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
1.866.901.BREW (2739)
24
Warranty
US
“Changes or modifications not expressly approved by Keurig, Incorporated could void
the user’s authority to operate the equipment.”
“This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•C
onnect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.”
Canada
Under Industry Canada regulations, this radio transmitter may only operate using
an antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Conformément à la réglementation d’Idustrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé
pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et
son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse
pas l’intensité necessaire à l’étabissement d’une communication satisfaisante.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement
RF Exposure Warning
To comply with FCC and Industry Canada RF radiation exposure limits for general
population, this device must be installed such that a minimum separation distance
of 20cm is maintained between its antenna and all persons. This device must not be
collocated or operated in conjunction with any other antenna or transmitter.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
25
Notes
26
27
Keurig, Incorporated
55 Walkers Brook Drive
Reading, MA 01867
Keurig, Incorporated is a wholly-owned subsidiary
of Green Mountain
Coffee Roasters, Inc.
For Commercial Use Only
Made in China.
Printed in China.
© 2012 Keurig, Incorporated
All rights reserved
www.keurig.com | 1.866.901.BREW
P/N 60-201396-000 Rev A 06/12