INSTALLATION & OPERATING
INSTRUCTIONS
NANOV SERIES
36” TOP DIRECT VENT GAS APPLIANCE
WARNING: If the information in this manual
is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
—
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
—
What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the
fire department.
—
For Residential Use - Meets All HUD
Requirements For Manufactured Housing Installations
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
CAUTION:
Do not expose the appliance to the elements (such as
rain, etc.).
U.S. Patent 5,613,487
Note: Read these instructions completely before beginning installation. Failure to follow them could cause an appliance malfunction
resulting in serious injury and/or property damage.
WARNING!
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this
manual. For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
01-03
1
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Table of Contents
A. Appliance Specifications .............................................................................................................................. 3
NANOV COMPONENTS .............................................................................................................................. 4
NANOV Optional Installation Components: .................................................................................................. 4
B. Location and Clearances ............................................................................................................................. 5
C. Framing ....................................................................................................................................................... 6
D. Setting the Appliance ................................................................................................................................... 6
E. Venting ........................................................................................................................................................ 7
F. Utilities ...................................................................................................................................................... 14
G. Finishing .................................................................................................................................................... 21
H. Appliance Preparation ................................................................................................................................ 21
I. Lighting Instructions ................................................................................................................................... 23
J. Seasonal Checklist .................................................................................................................................... 24
K. Start-up Issues .......................................................................................................................................... 25
L. Maintenance Instructions ........................................................................................................................... 26
M. Optional Components ................................................................................................................................ 28
N. Replacement Parts .................................................................................................................................... 29
Index ......................................................................................................................................................... 31
Warranty .................................................................................................................................................... 32
WARNING!
DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been under
water.
SAFETY PRECAUTIONS
34617 Rev D
1.
Please read these installation instructions completely
before beginning installation procedures. Failure to
follow them could cause an appliance malfunction
resulting in serious injury and/or property damage.
2.
Always check your local building codes prior to
installation. This installation must comply with all
local, regional, state and national codes and
regulations.
3.
Installation and repair should be done by a qualified
service person. This appliance should also be
inspected annually by a qualified service person. More
frequent inspections/cleaning may be required due
to excessive lint from carpeting, bedding materials,
etc. It is imperative that the control compartment,
burners and circulating air passageways of the
appliance be kept clean.
4.
This is a vented decorative gas appliance. Do not
burn wood or other material in this appliance.
5.
NEVER leave children unattended when there is a
fire burning in the appliance.
2
6.
This appliance may only use the approved venting
systems shown in these installation instructions.
Venting must not be connected to chimney flue
servicing a solid fuel burning appliance or a gas fuel
burning appliance.
7.
NEVER use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liquids in
this appliance. Keep any flammable liquids a safe
distance from the appliance.
8.
While servicing this appliance, always shut off all
electricity and gas to the appliance. This will prevent
possible electrical shock or burns. Also, make sure
the appliance is completely cooled before servicing.
9.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
10. Be sure to provide adequate clearances around the
air openings into the combustion chamber and
adequate accessibility clearances for servicing and
proper operation.
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
A. APPLIANCE SPECIFICATIONS
1. U.S. AND CANADA CERTIFICATION
The NANOV Series gas appliance has been tested in
accordance with the ANSI standard Z21.88-2000 in
the United States, and the current CSA 2.33-2000 in
Canada, and has been listed by Underwriters
Laboratories Inc. for installation as described in this
manual. All components are UL, AGA, CGA or CSA
safety certified.
2. LOCAL CODES
This installation must conform with local codes. In
the absence of local codes comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition, in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
The NANOV Series gas appliance has been tested
and listed for use in manufactured housing (mobile
homes). These installation instructions conform with
the Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280, or when such a
standard is not applicable, the standard for
Manufactured Home Installations, ANSI A225.1.
For assistance during installation contact your local
dealer or contact the Heatilator Technical Services
Department, Hearth & Home Technologies, 1915 W.
Saunders Street, Mt. Pleasant, Iowa 52641,
1-800-843-2848.
HEATILATOR and NANOV are registered trademarks
Hearth & Home Technologies, Division HON
INDUSTRIES.
3. GLASS SPECIFICATIONS/CERTIFICATIONS
Heatilator gas appliances manufactured with
tempered glass may be installed in hazardous
locations such as bathtub enclosures as defined by
the CPSC. The tempered glass has been tested and
certified to the requirements of ANSI Z97.1-1984 and
CPSC 16 CFR 1202. (Safety Glazing Certification
Council SGCC# 1595 and 1597. Architectural Testing,
Inc. Reports 02-31919.01 and 02-31917.01.)
This statement is in compliance with SPCS 16 CFR
Section 1201.5 “Certification and labeling
requirements” which refers to 15 USC 2063 stating
“…Such certificate shall accompany the product or
shall otherwise be furnished to any distributor or
retailer to whom the product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations.
Glass meeting this requirement is available from the
factory. Please contact your dealer or distributor to
order.
Typical Horizontal Installation
01-03
Typical Vertical Installation
3
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Note: Minimum and maximum clearances must be
maintained at all times. Illustrations throughout these
instructions reflect typical installations and are for design
purposes only. Actual installation may vary slightly due
to individual design preferences.
The illustrations and diagrams used throughout these
installation instructions are not drawn to scale.
Tools and building supplies normally required for
installation:
Saw
Pliers
Hammer
Phillips Screwdriver
Tape Measure
Plumb Line
Level
Wall-finishing materials
Framing material
Surround
Caulking material
Gloves
Framing Square
Electric Drill/Bits
NANOV COMPONENTS
NANOV (GNDC36) 36" Top Direct
Vent Decorative Gas Appliance
F K 4 F an K i t
VP-TH Horizontal Termination Cap
VP6-9 Slip Section
WS6 Wall Shield
NAVP90ST Starter Elbow
LP Conversion Kit
NANOV OPTIONAL INSTALLATION COMPONENTS:
Components
NAVP-TV
Vertical Termination Cap
NAVP45
45° Elbow
NAVP90
90° Elbow
NARF6
Roof Flashing (vertical termination for 0/12 to 6/12 pitch)
NAVP12
12" Length Vent Pipe
NAVP36
36" Length Vent Pipe
NAVP48
NAVP-THK-MI
48" Length Vent Pipe
Non-unitized VP-TH Kit (starter elbow, vent section, wall shield, termination cap)
NAFS6
Firestop Spacer
VP12MI
12" Vent Pipe, non-unitized (can be cut to length)
VP24MI
24" Vent Pipe, non-unitized (can be cut to length)
VSS2
34617 Rev D
Description
Vinyl Soffit Shield
4
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
B. LOCATION AND CLEARANCES
Appliance Dimensions
WARNING!
Due to high temperatures, the appliance should be located out of
traffic and away from furniture and draperies.
1. APPLIANCE LOCATIONS AND SPACE
REQUIREMENTS
Figure 1 illustrates a variety of ways the appliance
may be located in a room. The NANOV Series may be
installed directly on the floor or raised on a hearth.
These appliances are certified for installation in a
bedroom, bed/sitting room or in manufactured
housing (mobile homes) in the U.S. and Canada.
2. CLEARANCES
Figure 2 shows all clearances that must be
maintained around the appliance. See page 10 for
termination cap clearances.
Figure 2
Appliance Clearances to Combustible Materials
Figure 1
Appliance Locations
01-03
CAUTION:
Do not expose appliance to the elements (such as
rain, etc.).
5
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
C. FRAMING
Figure 3 shows a typical framing of this appliance using combustible materials. Figure 4 shows the mantel heights for
mantel projections. All required clearances to combustibles must be adhered to.
Figure 4
Mantel Heights
CAUTION:
Wear gloves and safety glasses for protection.
Figure 3
Framing
CAUTION:
WARNING!
To prevent contact with sagging or loose insulation,
the appliance must not be installed against vapor
barriers or exposed insulation.
Provide adequate clearances around the air
openings into the combustion chamber and
adequate accessibility clearances for servicing
and proper operation.
D. SETTING THE APPLIANCE
This appliance may be placed on a smooth combustible or noncombustible continuous, flat surface. When the appliance
is installed directly on carpeting, tile or other combustible material other than wood flooring, the appliance shall be
installed on a metal or wood panel extending the full width and depth of the appliance. Slide the appliance into position
and level the appliance from side-to-side and front-to-back. Shim with noncombustible material as necessary.
Secure the appliance by bending out the nailing flanges on each side of the appliance and nail to framing. The nailing
flanges have been positioned 5/8 inch back from the front of the appliance to allow the addition of drywall.
34617 Rev D
6
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
E. VENTING
1. HORIZONTAL VENT TERMINATION
(USING SUPPLIED PIECES ONLY)
This kit is supplied with a standard vent kit that will
meet the majority of installations for this Heatilator
appliance. This kit consists of a 90° starter elbow, a
6-9” slip section, a wall shield, and a termination cap.
A typical installation using these parts is diagrammed,
along with the clearances to combustible materials
around the vent, in Figure 5.
CAUTION:
Provisions shall be made to provide adequate
combustion and ventilation air.
a. Vent Lengths
Various venting configurations are shown in
Figures 6-9 from which maximum vent lengths
can be determined.
Figure 6
Vent Lengths with One Elbow
(minimum vertical)
Figure 5
Clearances
WARNING - RISK OF FIRE!
This appliance may only use the direct vent
chimney system designed for use with the
appliance and must not be connected to a chimney
flue servicing a separate solid fuel or gas fuel
burning appliance.
WARNING - RISK OF FIRE!
If you have chosen horizontal termination, be sure
there are no future obstructions from trees,
bushes, snow drifts, etc.
Figure 7
Vent Lengths with One Elbow
(2’ vertical or more, 25’ maximum)
01-03
7
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Figure 9
Vent Lengths with Three Elbows
Figure 8
Vent Lengths with Two Elbows
b. Assembling Vent Sections
Note: Horizontal runs will require the use of one
vent support (or plumbers tape) for every 3’ of vent.
Use only pipe supplied and listed for use with
this appliance. See page 4 for a description of
listed components. See Section 3 on page 13 for
instructions on assembling the vent sections.
WARNING - RISK OF FIRE!
Always maintain minimum air space clearances
or greater around the chimney system. See Figure
5. Do not pack air spaces with insulation or other
material.
WARNING!
The horizontal run of vent must have a ¼” rise for
every 1 ft. of run towards the termination. Never
allow the vent to run downward. This could cause
high temperatures and may present a fire hazard.
WARNING!
The first 90° elbow on a top direct vent appliance
MUST be a NAVP90ST; this starter elbow includes
a deflector.
34617 Rev D
8
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
c. Installing the Interior Wall Shield (WS6)
Frame a hole in a combustible wall for an interior
wall shield, as shown in Figure 10, whenever a
wall is penetrated. This shield maintains
minimum clearances and prevents cold air
infiltration.
Note: Exterior wall thickness must be a
minimum of 4” to a maximum of 23½”.
Secure the wall shield to the framing as shown
in Figures 11 and 12.
The termination cap height must meet all local
and national codes and not be easily blocked or
obstructed.
If the material being penetrated is of
noncombustible materials, a 9” diameter hole is
acceptable.
Figure 11
Interior Wall Shield
Figure 10
Exterior Wall Hole
Figure 12
Venting Through the Wall
WARNING - RISK OF FIRE!
Always maintain minimum air space clearances or
greater around the chimney system. The flow of
combustion and ventilation air must not be
obstructed.
CAUTION:
A vinyl soffit shield (VSS2) should be installed if a
cap is within 30” of a vinyl soffit.
d. Termination
Vent termination must not be recessed in the wall or siding. Siding may be brought to the edge of the cap base.
Install the cap as shown in Figure 12. Cap pipe sections should overlap the vent pipe by 1½ inches. Caulk
outside edges of cap.
Local codes may require the installation of a shield (CS) which prevents the cap from accidentally touching
anything or anyone.
Figure 13 illustrates cap locations prescribed by current ANSI Z273.1 and CAN/CGA-B149 Installation Codes.
01-03
9
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Figure 13 - Termination Cap Locations
DIMENSION DESCRIPTIONS
A
Clearance above the ground, a veranda, porch, deck or
balcony - 12 inches (30 cm) minimum. *
O
Horizontal clearance between two horizontal termination
caps – 12 inches (30 cm) minimum.
B
Clearance to window or door that may be opened – 10,000
BTUs or less, 6 inches (15 cm) minimum; 10,000-50,000
BTUs, 9 inches (23 cm) minimum; over 50,000 BTUs, 12
inches (30 cm) minimum. *
*
As specified in CGA B149 Installation Codes
C
Clearance to permanently closed window – 12 inches (30
cm) minimum - recommended to prevent condensation on
window.
**
D
Vertical clearance to ventilated soffit located above the
termination within a horizontal distance of 2 feet (60 cm)
from the centerline of the termination – 18 inches (46 cm)
minimum. **
E
Vertical clearance to unventilated soffit - 12 inches (30 cm)
minimum. **
F
Clearance to outside corner - 6 inches (15 cm) minimum.
G
Clearance to inside corner - 6 inches (15 cm) minimum.
H
Not to be installed above a meter/regulator assembly within
3 feet (90 cm) horizontally* from the center line of the regulator
I
Clearance to service regulator vent outlet - 6 feet (1.8m)
minimum. *
J
Clearance to non-mechanical air supply inlet into building or
the combustion air inlet to any other appliance - 12 inches
(30 cm) minimum. *
K
Clearance to mechanical air supply inlet - 6 feet (1.8 m)
minimum. *
L
Clearance above a paved sidewalk or paved driveway
located on public property - 7 feet (2.1 m) minimum.
Note: Local codes or regulations may require different
clearances.
Clearance required to vinyl soffit material – 30 inches (76
cm) minimum. With a vinyl soffit shield – 18 inches (46 cm)
minimum.
WARNING!
In the U.S.: Vent system termination is NOT permitted in
screened porches. You must follow side wall, overhang
and ground clearances as stated in the instructions.
In Canada: Vent system termination is NOT permitted in
screened porches. Vent system termination is permitted in
porch areas with two or more sides open. You must follow
all side wall, overhang and ground clearances as stated in
the instructions.
Hearth & Home Technologies assumes no responsibility for
the improper performance of the appliance when the venting
system does not meet these requirements.
A vent may not terminate directly above a sidewalk or paved
driveway which is located between two single family
dwellings and serves both dwellings.
M
Clearance under veranda, porch, deck or balcony - 12 inches
(30 cm) minimum. * Recommended 30 inches (76 cm) for
vinyl or plastic.
Only permitted if veranda, porch, deck or balcony is fully
open on a minimum of 2 sides beneath the floor. *
N
34617 Rev D
Vertical clearance between two horizontal termination caps
– 12 inches (30 cm) minimum.
10
Figure 14 - Cap Clearances
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
2. VERTICAL TERMINATION
a. Clearances
See Figure 15 for clearance information.
Figure1 5
Vertical Termination Clearances
Figure 17
Vertical Termination Vent Lengths
b. Vent Lengths
Various venting configurations are shown in
Figures 16 and 17 from which maximum vent
runs can be determined.
WARNING - RISK OF FIRE!
Always maintain minimum air space clearances
or greater around the chimney system. Do not pack
air space with insulation or other material.
WARNING!
The horizontal run of vent must have a ¼” rise for
every 1 ft. of run towards the termination. Never
allow the vent to run downward. This could cause
high temperatures and may present a fire hazard.
c. Assembling Vent Sections
Use only pipe supplied and listed for use with
this appliance. See page 4 for a description of
listed components. See Section 3 on page 13 for
instructions on assembling vent sections.
Figure 16
Vertical Termination Vent lengths
01-03
11
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
d. Firestop Spacer/Chimney Installation
Frame an opening and install a firestop spacer
(NAFS6) whenever the vent penetrates a ceiling/
floor area, as shown in Figure 18. Frame the
opening with the same sized lumber as used in
the ceiling/floor joists. Unless the flue is offset,
the hole should be directly above the appliance.
DO NOT pack insulation around the chimney.
Figure 19
Chimney Height for Vertical Termination
Figure 18 - Installing the Firestop Spacer
Figure 20 - Multiple Vertical Termination
e. Chase/Termination Installation
Figures 19 and 20, and Table 1 specify minimum
chimney heights for various pitched roofs.
These chimney heights are necessary for safety
and do not ensure draft-free operation. Trees,
buildings, adjoining roof lines, adverse
conditions, etc. may create a need for a taller
chimney should down drafting occur.
f.
Installing the Vertical Termination Cap
To install the NAVP-TV, slide the inner collar of
the cap over the inner vent and place the outer
collar of the cap over the outer vent. Secure with
three screws into the outer vent.
Note: To ensure proper operation, verify all
venting and the termination are unobstructed.
34617 Rev D
12
ROOF PITCH
H (MIN.) FT.
Flat to 6/12 ................................... 1.0
6/12 to 7/12 .................................. 1.25
Over 7/12 to 8/12 ......................... 1.5
Over 8/12 to 9/12 ......................... 2.0
Over 9/12 to 10/12 ....................... 2.5
Over 10/12 to 11/12 ..................... 3.25
Over 11/12 to 12/12 ..................... 4.0
Over 12/12 to 14/12 ..................... 5.0
Over 14/12 to 16/12 ..................... 6.0
Over 16/12 to 18/12 ..................... 7.0
Over 18/12 to 20/12 ..................... 7.5
Over 20/12 to 21/12 ..................... 8.0
Table 1 - Chimney Height
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
3. ASSEMBLING THE VENT SECTIONS
a. Attaching the Venting to the Appliance
To attach the first vent pipe section to the appliance
collars, simply slide the flared end of the inner
flue of the vent section over the inner collar on the
appliance. At the same time, insert the outer flue
into the outer collar on the appliance. Push the
vent section into the appliance collar until all the
lances have snapped into place. Tug slightly on
the vent to confirm it has completely locked in
place.
b. Assembling Vent Sections
1)
Start the flared inner flue of section “A” over the
inner flue of section “B”.
2)
Insert the outer flue of section “A” into the outer
flue of section “B”. See Figure 21.
Figure 21
Note: Squeezing the pipe slightly to fit may
be necessary.
Once both inner and outer flues are started,
press section “A” into section “B” firmly until
all lances have snapped into place. Tug
slightly on section “A” to confirm it has
completely locked into place. See Figure 22.
Note: Make sure that the seams are NOT
aligned in order to prevent unintentional
disconnection.
Figure 22
c. Assembling Minimum Installation (MI)
Sections (not required for all installations)
MI sections are non-unitized so that they can be
cut to a certain length. To use these sections, they
must be cut to length from the non-expanded end.
See Figure 23. They can then be attached by first
connecting the expanded end of the MI inner flue
with the inner flue from the adjacent vent section
and securing with three screws. The expanded
portion of the MI inner flue must overlap completely
with the untreated end of the adjacent vent section.
The outer flue can then be inserted into the
adjacent outer flue expanded end and attached to
the next vent section with three screws. The other
end of the MI vent section can then be attached by
fitting a snap lock section to it and snapping it
together as normal.
01-03
Figure 23
13
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
d. Assembling the Slip Sections
Slip sections should be snapped into the first
mating piece, then expanded to their desired
length, making sure that a 1.5” overlap is
maintained between the two sections of the slip
section. The sections need to be secured by
driving two screws through the overlapping
portions of the vent. See Figure 24. This will
secure the slip section to the desired length and
prevent it from separating. The slip section can
then be attached to the next section of vent.
e. Disassembling Vent Sections
(only if necessary)
To disassemble any two pieces of pipe, rotate
either section so that the seams on both pipe
sections are aligned as shown in Figure 25. They
can then be carefully pulled apart.
Figure 24
Figure 25
F. UTILITIES
1. HIGH ALTITUDE INSTALLATION
For U.S. installation, appliances are tested and approved for elevations from 0-2000 feet. When installing this appliance
at an elevation above 2000 feet, National Fuel Gas Codes require a decrease of the input rating by changing the
existing burner orifice to a smaller size. Input should be reduced 4% for each 1000 feet above sea level. Check with
the local gas utility for proper orifice size identification. Orifices are available from your Heatilator distributor.
For Canada, appliances are certified for elevations from 0-4500 feet. When installing this appliance at an elevation
between 0-4500 feet in Canada, the input rating does not need to be reduced. When installing this appliance at an
elevation above 4500 feet in Canada, check with local authorities.
2. GAS LINE CONNECTION
The appliance is provided with a stainless steel flexible connector and manual shutoff valve. See Figure 26. The
incoming gas line should be piped into the valve compartment and connected to the 1/2” FIP connection provided on
the manual shutoff valve. All connections must be tightened and checked for leaks with a soap and water solution
or leak detector. Bleed the gas line to extract any air that may have been trapped inside the pipe. See Figure 27 to
connect the gas line. Gas connections may also be made by taking out the knockout in the bottom pan to allow
connection through the bottom of the appliance.
34617 Rev D
14
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Note: The appliance and its manual shutoff valve
must be disconnected from the gas supply piping
system during any pressure testing of that system at
test pressures in excess of 1/2 psi (3.5 kPa). The
appliance must be isolated from the gas supply
piping system by closing its manual shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2
psi (3.5 kPa).
WARNING!
This valve has been preset at the factory. Altering
settings may result in fire hazard or bodily injury.
Figure 26
Flexible Connector and Manual Shutoff Valve
Figure 27
Gas Line
3. GAS PRESSURE
A pressure tap is included on the front face of the standing pilot gas control valve.
Table 2 shows optimum gas pressure information.
Consult your local gas company for assistance in determining the proper orifice for your altitude or refer to ANSI
Z223.1-latest edition, Appendix F.
NANOV
Inlet gas supply pressure (natural gas)
4.5 (min.) - 7.0 (max.)*
Optimum manifold pressure (natural gas)
3.5*
Inlet gas supply pressure (LP gas)
11.0 (min.) - 14.0 (max.)*
Optimum manifold presure (LP gas)
10*
Input rate (natural gas ) 36"
Input rate (propane gas) 36"
27,000 BTU/hr.
25,000 BTU/hr.
Natural Gas Orifice size
Propane Gas Orifice size
.101 in./2.56 mm.
.059 in./1.50 mm.
Table 2
Gas Information for Standing Pilot Appliances
* measurement in inches/water column
01-03
15
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
4. CONVERSION TO PROPANE GAS (IF APPLICABLE)
This appliance is equipped for natural gas. In the event your appliance must be converted to propane, a conversion
kit is supplied to allow that to be done. The conversion should only be done by a qualified technician using these
Hearth & Home Technologies specified and approved parts. See Figure 28.
1 - Valve Regulator (10.5” w.c.)
2 - Brass Burner Orifice (.059”)
3 - Pilot Orifice (.010”)
4 - Conversion Label
Figure 28
Conversion Kit
In the United States:
WARNING!
This conversion kit is to be installed by a qualified service technician in accordance with the manufacturer’s
installation instructions and all codes and requirements of the authority having jurisdiction. Failure to follow the
instructions could result in a fire, explosion, or production of carbon monoxide causing property damage,
serious injury, or loss of life. The qualified agency performing this work assumes responsibility for proper
installation of this kit. The installation is not proper and complete until the operation of the converted appliance
is checked as specified in the owner instructions supplied with the kit.
In Canada:
“The conversion shall be carried out in accordance with the requirements of the provincial authorities having
jurisdiction and in accordance with the requirements of the CAN1-B149.1 and .2 installation code.”
CONVERSION STEPS:
Step 1
Open the control access panel so you can observe
the control area of the gas appliance. See Figure 29.
Step 2
Turn off the gas and electrical power.
a. To turn off the gas and locate the manual shutoff
valve in the control area in the bottom of the
appliance, turn the manual shutoff valve so it is
perpendicular to the gas line. See Figure 30.
Figure 29
Removing Control Access Panel
b. If electricity has been brought to the appliance for
a fan or remote control, shut off all power by
turning off the appropriate circuit breaker or
removing the fuse in the electrical panel.
Figure 30
Manual Shutoff Valve
34617 Rev D
16
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Step 3
a. Using the regulator replacement kit, follow the instructions (Steps 1-3) that come with the kit. After completion
of Step 3 from the kit’s instructions, return to these instructions.
b. Remove the tamper-proof cover screw from the natural gas regulator (using snap ring pliers) and install the
cover screw onto the propane gas regulator.
Figure 31
Robertshaw Standing Pilot Valve in the “OFF” Position
Step 4
a. Removing Logs
Follow the instructions for removing the glass, screen and logs on page 27.
b. Removing the Burner
Using a phillips screwdriver, remove the screws from each corner of the burner. Carefully pull the burner to the
left, off of the burner orifice underneath. Set the burner aside.
Step 5
a. Pilot Orifice
Loosen and remove the screws that hold the pilot bracket to the pilot assembly (four screws in all). Remove the
pilot bracket. Using a 1/2” wrench, loosen and separate the pilot nut from the pilot assembly. See Figure 32. The
aluminum pilot may have to be bent slightly to separate the parts. Replace the natural gas pilot tube orifice
(which will either have come out with the pilot nut or will be in the pilot assembly and have to be pulled out) with
the LP pilot orifice supplied with the conversion kit. With the new orifice in place, tighten the pilot nut to the pilot
assembly and reattach the pilot bracket to the pilot assembly and to the seal plate.
Note: Test fittings for leaks with the pilot lit and the burner off as indicated in Step 6.
Figure 32
01-03
17
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Step 7 - Checking the Pressure
b. Burner Orifice
Completely loosen the nut securing the orifice
with a 5/8” wrench (refer to Figure 33). Remove
the orifice and replace it with the propane orifice.
Tighten the nut.
c. To adjust the air shutter at the base of the burner
tube/neck, loosen the 1/4” screw using either a
1/4” nut driver or “stubby” screwdriver. Slide the
shutter fully open and secure. See Figure 33.
Figure 33 - Burner Orifice
d. Return the burner to its position on the orifice
and secure it with four screws, one at each corner.
Test for leaks between the valve and burner with
the burner lit as indicated in Step 6.
a. The gas input, inlet gas supply pressure and
manifold pressure must be as indicated on the
rating label located in the control area of the
appliance. Any other input, inlet pressure or
manifold pressure could cause your gas
appliance to operate other than intended and
could cause serious injury or property damage.
b. Inlet Pressure
Verify that the gas valve is set at the “PILOT”
position. Verify the inlet gas supply pressure by
loosening the screw located inside the inlet
pressure tap. See Figure 34. Connect a
Manometer to the inlet pressure tap by pushing
the Manometer hose over the pressure tap. Turn
the valve to the “ON” position and turn the burner
on (with wall switch, remote, etc.). If the inlet gas
pressure is incorrect, do not adjust without
specific approval and instruction from the gas
supplier. Changing the inlet pressure may affect
other appliances in the residence. When
finished, return the valve to the “PILOT” position,
disconnect the Manometer and tighten the inlet
pressure tap screw.
Step 6 - Leak Test
a. This is important! Propane (LP) gas is heavy. If
there is an incomplete gas line connection the
gas could leak and settle to the lowest point and
then accumulate. Such a situation could be
hazardous. Do not proceed until all connections
are checked and any leaks eliminated!
b. Turn on the gas.
c. Test all gas connections for possible leaks by
using a soap/water solution or Sniffer (turn on
and calibrate the Sniffer, then place the sensor
end of the sniffer within 1/2” of each connection).
If the soap/water solution or Sniffer indicates there
is a leak, tighten and seal the connection and
then retest.
d. Turn the position indicator to the “PILOT” position
and depress. Press the push button ignitor and
light the safety pilot. Continue holding the position
indicator in the depressed position until the pilot
stays lit (approximately 45 seconds). Test for leaks
at the pilot assembly using one of the methods in
Step 6c.
e. Turn the position indicator to the “ON” position
and test for leaks at the valve and the burner orifice
using one of the methods in Step 6c.
34617 Rev D
18
Figure 34 - Valve Pressure Test
c. Outlet Pressure
Verify that the gas valve is set at the “PILOT”
position. Verify the manifold pressure by
loosening the screw located inside the outlet
pressure tap. See Figure 34. Connect a
Manometer to the outlet pressure tab by pushing
the Manometer hose over the pressure tap. Turn
the valve to the “ON” position, ignite the
appliance, and ensure that the pressure is
between 3” and 4” water column (optimum
pressure is 3.5” WC) for natural gas and
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
between 10” and 11” water column (optimum
pressure is 10.5” WC) for propane. If the outlet
gas pressure is incorrect, contact the gas
supplier or Heatilator Technical Services. When
finished, turn the valve back to the “PILOT”
position, turn off the burner, disconnect the
Manometer and tighten the outlet pressure tap
screw.
WARNING!
Do not leave the pressure too low or too high.
This will create a safety hazard!
CKP
THIS PLATE MUST BE AFFIXED AS CLOSE AS
POSSIBLE TO THE EXISTING RATING PLATE.
THE FOLLOWING MUST BE COMPLETED BY THE INDIVIDUAL
CONVERTING THIS APPLIANCE FROM NATURAL GAS TO
PROPANE GAS.
This appliance has been converted on (date) MO-DAY-YEAR
to propane gas with Kit * CKP by (name and address of
organization making this conversion) JOHN SMITH
DISTRIBUTING, 1234 ANYWHERE RD., ANYWHERE,
STATE/PROVINCE,
who accepts the responsibility for the correctness of this
conversion.
22330A
Step 8 - Resetting the Appliance
Figure 35 - Conversion Label
a. Replace the logs as shown on page 27.
b. Replace the glass and screen as shown on
THIS CONTROL
HAS BEEN CONVERTED
TO LP
page 27.
Step 9 - Attaching the Labels
a. The installer conversion label and valve
manufacturer labels must be completed and
installed by the individual completing the
conversion. This must be finished or the
conversion is not complete. See Figures 35-37.
Figure 36 - Robertshaw Conversion Label
b. To fill out the installer conversion label, follow the
example in Figure 35. After filling out the label,
clean an area near the existing rating label and
attach.
Attach the valve manufacturer conversion
labels as indicated in Figure 37.
Figure 37
Robertshaw Conversion Label Placement
5. WIRING
a. Wall Switch Wiring
The installer shall supply a UL-listed or in
Canada, a CSA-listed wall switch. This appliance
was tested with eighteen feet of UL listed 18 ga.
Type CL2 105°C, two conductor “thermostat wire.”
If other wiring materials are used they shall
comply with local codes. In the absence of local
codes, they shall comply with the National
Electrical Code ANSI/NFPA 70-latest edition or
Canadian Electrical Code CSA C22.1.
b. Standing Pilot Ignition
A wiring diagram is shown in Figure 38. You must
wire for the fan kit supplied with this appliance at
installation to avoid reconstruction.
Note: This appliance must be electrically wired and
grounded in accordance with local codes or, in the absence
of local codes, with National electric Code ANSI/NFPA 70latest edition or the Canadian Electric Code CSA C22.1.
01-03
Figure 38 - Standing Pilot Ignition Wiring Diagram
19
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
c. Junction Box Wiring
We recommend you operate the two outlets on
separate circuits. This allows independent
operation of the appliance and fan. Independent
operation is obtained by using minimum 14-3 with
ground Romex and separating the two outlets by
breaking out the tab as shown in Figure 39
6. JUNCTION BOX INSTALLATION
INSTRUCTIONS
a.
Remove the junction box assembly from the valve
compartment.
b.
If the box is being wired from the OUTSIDE of the
appliance:
c.
d.
34617 Rev D
1)
Loosen two screws on the Romex connector,
feed the necessary length of wire through
the connector and tighten the screws.
2)
Make all necessary wire connections to the
receptacle and assemble the receptacle and
cover to the junction box.
3)
Attach the junction box assembly to the
outside of the appliance with the two screws
provided.
If the box is being wired from the INSIDE of the
appliance:
1)
Pull the electrical wires from outside the
appliance through this opening into the valve
compartment.
2)
Loosen the two screws on the Romex
connector, feed the necessary length of wire
through the connector and tighten the screws.
3)
Make all necessary wire connections to the
receptacle and assemble the receptacle and
cover to the junction box.
4)
Attach the junction box assembly to the inside
of the appliance with the two screws
provided.
Figure 39 - Junction Box Detail
WARNING!
This appliance DOES NOT require a 110V AC supply
for operation. Connecting the appliance/wall switch
to a 110V AC supply will cause the appliance to
malfunction and destroy the valve and thermopile.
If the box is not to be wired at the time of appliance
installation, assemble the receptacle and cover
to the box and install on the inside of the
appliance.
20
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
G. FINISHING
1. COMBUSTIBLE FINISHING MATERIAL
Material made of or surfaced with wood, compressed paper, plant fibers, plastics, or any material
capable of igniting and burning, whether flame
proofed or not, plastered or unplastered (this
includes drywall).
2. NONCOMBUSTIBLE FINISHING
MATERIAL
Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick,
tile, concrete, slate, glass or plasters, or combination thereof, or have a UL Fire rating of zero.
Figure 40
Finishing Materials
3. HIGH TEMPERATURE SEALANT
MATERIAL
Sealants that will withstand high temperatures;
General Electric RTV103 (Black), or equivalent.
Rutland, Inc. Appliance Mortar #63, or equivalent.
A high temperature sealant, 1/8 inch wide bead
minimum, must be used to close off gaps between
the appliance and facing to prevent cold air leaks.
See Figure 40.
WARNING!
Grilles on this appliance cannot, in any way, be
covered as it may create a fire hazard.
H. APPLIANCE PREPARATION
1. ATTACHING THE HOOD
The hood is to be located above the glass panel.
The hood must be attached or a fire hazard may
result. Locate the four screws just inside the upper
section of the appliance. Position the hood and slide
into position. Tighten the four screws. See Figure 41.
2. UPPER GRILLE PANEL REMOVAL
Grasp the upper grille panel and remove the rubber
pins holding the grille. See Figure 42.
3. CONTROL ACCESS PANEL REMOVAL
Release the spring pin on the right hand side of the
control access panel. See Figure 43.
4. GLASS AND SCREEN REMOVAL
Figure 42 - Upper Grille Panel Removal
See page 27 of this manual.
Figure 41 - Installing the Hood
01-03
Figure 43 - Control Access Panel Removal
21
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
5. APPLIANCE PREPARATION
c. Placing the Rock Wool
a. Log Set
Remove two shipping bands from the log set
(Figure 44) and reassemble. The log set should
look similar to that in Figure 45.
Place a small amount of 1/2” diameter pieces
(dime-size) of rock wool on the burner pan so
that the rock wool touches but does not cover the
holes in the burner pan. This will provide the
“glowing embers” look. See Figure 47.
Figure 44 - Log Set Banded for Shipping
Figure 47
Placing the Rock Wool
(top logs removed for clarity)
6. GLASS AND SCREEN REPLACEMENT
See page 27 of this instruction manual.
WARNING! RISK OF CARBON MONOXIDE!
Do not hit or strike glass. Do not operate this appliance
with the glass removed, broken, or not sealed.
Figure 45 - Assembled Log Set
b. Placing the Lava Rock and Vermiculite
See Figure 46 for lava rock and vermiculite
placement.
7. CONTROL ACCESS PANEL
REPLACEMENT
Replace the control access panel as shown in
Figure 48.
Figure 46
Placing the Vermiculite and Lava Rock
(top logs removed for clarity)
34617 Rev D
Figure 48 - Replace Control Access Panel
22
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
I. LIGHTING INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING!
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.
A.
This gas appliance has a manual ignition device that lights the pilot. When lighting the pilot, follow these
instructions exactly.
B.
BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because
some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
•
•
•
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob to light the pilot. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it - call a qualified service technician. Force or attempted repair may
result in a fire or explosion.
D.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Do not use the appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS
STOP! READ THE SAFETY INFORMATION ABOVE ON THIS LABEL!
Turn wall switch to the “OFF” position or set
thermostat to lowest setting.
Open the control access panel.
Turn manual shutoff valve to “CLOSED”. Wait 5
minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP!
Follow “B” in the safety information above on this
label. If you don’t smell gas, go to the next step.
Turn manual shutoff valve to “OPEN”.
Turn pilot knob clockwise to “OFF” (knob may have
to be depressed to pass the “PILOT” position).
Locate pilot assembly inside the appliance.
Locate red ignitor button.
Turn pilot knob to “PILOT” and push in.
Continue to hold in pilot knob and push the red
ignitor button 12-15 times until small blue pilot flame
appears.
Continue to hold in pilot knob for approximately one
minute. Pilot should remain lit. If pilot goes out, wait
5 minutes and repeat Steps 4-9.
To light the main burner, release and turn knob
counterclockwise to “ON”. Do not light by hand.
If the appliance will not operate, follow the
instructions “To Turn Off Gas To Appliance” and call
your service technician or gas supplier.
1.
TO TURN OFF GAS TO APPLIANCE
Turn off the wall switch or set the thermostat to
the lowest setting.
2. Open the control access panel.
01-03
3.
Turn the manual shutoff valve to the “CLOSED”
position. Do not force.
4. Close the control access panel.
23
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
J. SEASONAL CHECKLIST
WARNING!
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to
avoid burns or clothing ignition. Young children should be carefully supervised when they are in the same room
as the appliance.
CAUTION:
Any safety screen or guard removed for servicing an appliance must be replaced prior to operating this
appliance.
Clothing or other flammable material should not be placed on or near the appliance.
1. STANDING PILOT OPERATION
Installation and repair should be done by a
qualified service person. The appliance
should be inspected before use and at least
annually by a qualified service person. More
frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.
Before operating this appliance, have a
qualified technician:
1. Review proper placement of logs, rock wool
and vermiculite.
2. Check the wiring.
Hearth & Home Technologies recommends you leave
the pilot on year round.
Lighting the Appliance During Regular Use
Turn the wall switch to “ON”.
Shutdown During Regular Use
Turn the wall switch to “OFF”.
If you decide to shut down the appliance for a long
period of time:
a. Turn all wall switches to “OFF”.
b.
Turn pilot knob on valve to “OFF”.
c.
Turn the gas line to “CLOSED.”
d.
To relight the appliance, see page 23.
2. FUEL
Do not burn wood or other material in this appliance.
This appliance is set for natural gas. Propane gas
conversions necessary to meet the application need
to be made by a qualified technician using Hearth &
Home Technologies specified and approved parts.
3. Check the air shutter adjustment.
4. Ensure there are no gas leaks.
5. Ensure the glass is sealed and in the proper
position.
6. Ensure the flow of combustion and ventilation air is not obstructed.
In the event your appliance must be converted to use
propane, you must use the conversion kit provided.
See page 16 for instructions on how to convert your
appliance.
WARNING!
Keep the area near the appliance clear and free
from combustible materials, gasoline, and other
flammable vapors and liquids.
34617 Rev D
24
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
WARNING!
Do not use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control system and any gas control which has been under
water.
K. START-UP ISSUES
ISSUE
SOLUTIONS
1.
Condensation on the glass.
1.
This is a result of gas combustion and temperature variations. As
the appliance warms, this condensation should disapear.
2.
Blue flames.
2.
This is a result of normal operation and the flames will begin to
yellow as the appliance is allowed to burn.
3.
Odor from appliance.
3.
When first operated, this appliance may release an odor for the
first several hours. This is caused by the curing of the paint and
the burning off of any oils remaining from manufacturing.
4.
Film on the glass.
4.
This is a normal result of the curing process of the paint and logs.
Glass should be cleaned wi thi n 4-6 hours of i ni ti al burni ng to
remove deposi ts left by oi ls from the manufacturi ng process. A
non-abrasive cleaner, such as Brasso may be necessary.
WARNING!
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or
similar liquids in this appliance. Keep any flammable liquids a safe distance from
the appliance.
01-03
25
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
L. MAINTENANCE INSTRUCTIONS
1. CLEANING THE BURNER AND
CONTROL COMPARTMENT
Keep the burner and control compartment clean by
brushing and vacuuming at least once a year. Failure
to do this may shorten the fan’s life (where applicable). Always turn off the wall switch (or remote
control) and gas valve before cleaning.
Note: The look of the flames and embers may differ
based on the type of fuel and venting assembly that
is used.
2. CHECKING THE FLAME PATTERNS
The thermopile and thermocouple (standing pilot)
tips should be covered with flame. See Figure 49.
Inspect the flame of the burner periodically, making
sure the flames are steady, not lifting or floating.
The flame color should be blue with yellow tips.
If the vent configuration is installed incorrectly, the
vent may cause the flames inside the appliance to lift
or “ghost,” which is a dangerous situation. Inspect
the flames after installation to ensure proper
performance. See Figure 50. If the vent configuration
is correct, yet the flames are lifting or ghosting, shut
off gas to the appliance and contact the dealer.
Figure 49
Standing Pilot
34617 Rev D
Figure 50
Flame Patterns
26
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
3. VENTING SYSTEM INSPECTION
The appliance and venting system should be
inspected before use, and at least annually by a
qualified field service person to ensure that the flow
of combustion and ventilation air is not obstructed.
4. CLEANING THE GLASS
See Figure 51.
Never operate this appliance without the glass
properly secured in place or if the glass if broken or
chipped.
In the event of glass breakage, carefully remove the
glass frame. This will allow the removal of all glass
fragments and sheet metal edge protection strips.
Vacuum all remaining glass pieces with a shop vac.
DO NOT VACUUM IF PIECES ARE HOT. Replace
glass with only a Heatilator brand glass panel
assembly ordered direct or through your local
distributor. Never use substitute material. Only fully
tempered soda lime safety glass or ceramic glass
may be used on this appliance.
Safety Note
Handle glass with care to
avoid striking, scratching or
slamming shut. NEVER
clean glass when it is hot.
Keep children and pets a
safe distance away.
Figure 51
Glass Cleaning
5. LOG REMOVAL/REPLACEMENT
If removal of the logs becomes necessary, remove
the two screws at the front of the grate. Grasp the two
outside upright grate bars. Pull the log/grate assembly toward the front and up, off the burner. See
Figure 52.
To replace the logs, grasp the two outside upright
grate bars. Push and lower the log set onto the
burner pan, making sure the back of the left most
grate bar slides through the grate mounting bracket
attached to the hearth pan. Attach two screws at the
front of the grate.
01-03
Figure 52 - Log Removal
27
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
M. OPTIONAL COMPONENTS
RC-SMART-HTL
Remote Control
RC-BATT-HTL
Battery-operated Remote
Control (Standing Pilot)
NACABTRIM3
Brass Cabinet Trim
(required with cabinet use)
RCT-MLT-HTL
Multi-Function
Remote Control
SMART-STAT-HTL
Remote Control with
Thermostat Control
SMART-BATT-HTL
Battery-operated Remote
Control with Thermostat
Control
WSK-MLT-HTL
Multi-Function Wall Switch
NAQKE2B Quick Tile
Surround
NAHN36WF
Light Oak Wall Cabinet
34617 Rev D
NAHN36CF
Light Oak Corner Cabinet
28
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
N. REPLACEMENT PARTS
Replacement parts are available from your distributor/dealer.
#1 - NANOV Series Gas Log Set
2
ITEM
PART #
DESCRIPTION
QTY.
1
34051
NANOV Series Log Set
1
2
21993
Hood - 36"
1
3
22123
Upper Grille - 36"
1
4
26804
Screen Assembly - 36"
1
5
22712
Glass w/Frame - 36"
1
6
21582
Lower Grille - 36"
1
7
FK 4
F an K i t
1
8
33858
Quick Access Latch
4
5
3
4
6
8
7
Visit our Website @ www.heatilator.com for a dealer/distributor near you!
01-03
29
34617 Rev D
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
HOMEOWNER’S NOTES
34617 Rev D
30
01-03
NANOV TOP DV GAS APPLIANCE INSTALLATION INSTRUCTIONS
Index
A
Appliance Locations 5
Appliance Preparation 21
Lava Rock 22
Rock Wool 22
Vermiculite 22
B
BTUs 15
Building Codes 3, 9
C
Certification 3
Chase Installation 12
Chimney Height 12
Clearances 5
Codes 3
Building 3, 9
Electric 19
Gas 3, 15, 16
Manufactured Housing 3
Combustible Materials 6
Components 4
Conversion 16
D
Disassembling Vent Sections 14
E
Electric Codes 19
Exterior Wall Hole 9
F
Finishing 21
High Temperature Sealants 21
Noncombustible Materials 21
Firestop Spacer Installation 12
Flames
Blue 25
Checking the flame patterns 26
Ghosting 26
Framing 6
Fuel 24
Fuel Conversion 16
Glass
Cleaning 27
Condensation 25
Film 25
Glass Specifications/Certifications 3
H
High Altitude Installation 14
High Temperature Sealant Material
21
Hood 21
Horizontal Installation 3
Horizontal Termination
Clearances 7
Vent Lengths 7
Safety Precautions 2
Seasonal Checklist 24
Setting the Appliance 6
Slip Sections 14
Space Requirements 5
Standing Pilot
Ignition 26
Operation 24
Start-up Issues 25
T
Termination Cap Locations 9
Termination Installation 12
I
U
Input Rate 15
Interior Wall Shield 9
Upper Grille 21
V
J
Mantel Heights 6
Manufactured Housing Codes 3
Minimum Installation (MI) Sections
13
Venting 13
Assembling 13
Assembling Minimum Installation
(MI) Sections 13
Attach to Appliance 13
Disassembling Vent Sections 14
Slip Sections - Assembly 14
Through the Wall 9
Vermiculite 22
Vertical Installation 3
Vertical Termination
Chimney Height 12
Clearances 11
Multiple Terminations 12
Vent Lengths 11
Vertical Termination Cap 12
N
W
Noncombustible Finishing Material
21
Noncombustible Materials 6
Wall Switch Wiring 19
Wiring 19
Diagram 19
Junction Box 20
Standing Pilot 19
Wall Switch 19
Junction Box 20
Junction Box Installation 20
L
Lava Rock 22
Lighting Instructions
Standing Pilot Ignition 23
Lot Set 22
M
O
Odor 25
Optional Components 4, 28
G
R
Gas Codes 3, 15, 16
Gas Line Connection 14
Gas Pressure 15
Replacement Parts 29
Rock Wool 22
01-03
S
31
34617 Rev D
Gas Appliance (Fireplace)
Limited Lifetime Warranty
HEARTH & HOME TECHNOLOGIES (“HHT”) extends the following warranty for HEATILATORâ gas appliances
installed in the United States of America or Canada (the “Appliance”). Dealers and employees of HHT have no authority to
make any warranty or authorize any remedies in addition to or inconsistent with the terms of this warranty.
Limited Lifetime Warranty
HHT warrants the Appliance for component failure due to a manufacturing defect of any of the following components:
combustion chamber, burner pan, and logs. The Limited Lifetime Warranty specified above is subject to the conditions,
exclusions and limitations listed below, is for the period the Appliance is owned by the original homeowner only, and is
nontransferable.
1 Year Limited Warranty
HHT warrants the Appliance to be free from failure of any of the following components for a period of one year after installation: valve, flexible gas line connector, glass panel, fan, direct vent chimney components, factory paint, gasket, piezo ignitor, thermopile, thermocouple, junction box, pilot assembly, shutoff valve, high limit switch, refractory liners, transformer, and
control box. If the Heatilator Appliance is found to be defective in either material or workmanship within one year of the date
of original installation, HHT will provide replacement parts at no charge and pay reasonable labor and freight costs, and is
for the period of one year following the date of original installation of the Appliance.
Conditions, Exclusions, & Limitations of Liability
A.
B.
C.
D.
Both the Limited Lifetime and 1 Year Limited Warranties supplied by HHT apply only while the Appliance is in its location of original installation. HHT’s obligation under this warranty does not extend to damages resulting from (1)
installation, operation or maintenance of the Appliance not in accordance with the Installation Instructions, Operating Instructions, and the Listing Agent Identification Label furnished with the Appliance; (2) installation which does
not comply with local building codes; (3) shipping, improper handling, improper operation, abuse, misuse, accident
or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing
construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other causes;
(5) use of fuels other than those specified in the Operating Instructions; (6) installation or use of components not
supplied with the Appliance or any other components not expressly authorized and approved by HHT; and/or (7)
modification of the Appliance not expressly authorized and approved by HHT in writing. This warranty is limited to
only the component parts manufactured or supplied by HHT.
HHT’s liability under both the Limited Lifetime Warranty and the 1 Year Limited Warranty is limited to the replacement and repair of defective components or workmanship during the applicable period. HHT may fully discharge
all of its obligations under such warranties by repairing the defective component(s) or at HHT’s discretion, providing replacement parts at no charge and paying reasonable labor and freight costs.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
Some states do not allow exclusions or limitations of incidental or consequential damages, so those limitations
may not apply to you. This warranty gives you specific rights; you may also have other rights which vary from
state to state.
How to Obtain Service
To obtain service under this warranty you must:
1. Send written notice of the claimed condition to Heatilator Technical Service Department, Hearth & Home
Technologies, 1915 W. Saunders Street, Mt. Pleasant, Iowa 52641-1563. You may also register your
claim online at www.heatilator.com/contact.asp.
2. Provide proof of purchase, model number, serial number, and manufacturing date code to HHT.
3. Provide HHT reasonable opportunity to investigate the claim, including reasonable opportunity to inspect
the Appliance prior to any repair or replacement work and before the Appliance or any component of the
Appliance has been removed from the place of original installation.
4. Obtain HHT’s consent to any warranty work before the work is done.
ADDITIONAL INFORMATION. If you would like information on current HEATILATOR products or want to locate a dealer in
your area, call 1-800-843-2848.
ã2001 Heatilatorâ is a Registered Trademark of Hearth & Home Technologies
34617 Rev D
32
01-03