INSTALLER’S & OWNER’S MANUAL
Designed For Superior Basement
and Crawlspace Dehumidification
P/N 4033600 • Serial No.________________________ Install Date:___________
Sold by:
4201 Lien Rd • Madison, WI 53704 • TOLL-FREE 1-800-533-7533 • www.Santa-Fe-Products.com
• sales@Santa-Fe-Products.com TS-749 12/13
For small usage:
SANTA FE COMPACT2 INSTALLER'S AND OWNER'S MANUAL
Thank you for purchasing the Santa Fe Compact. For questions regarding this product
or to order parts/accessories, contact your dealer or call TOLL-FREE 1-800-533-7533.
Table of Contents
1. 2. 3. 4. 4.1 4.2 Precautions ..........................................................2
Intended Application(s)..........................................2
Registrations ........................................................2
Specifications ......................................................3
Unit Assembly ......................................................3
Installing Feet .......................................................3
Drain Hose ...........................................................3
5. 5.1 5.2 5.3 5.4
Installation ...........................................................3
Safety Precautions ...............................................3
Location................................................................3
Electrical Requirements .......................................3
Condensate (Water) Removal................................3
6. 6.1 6.2 6.3 Operation .............................................................4
Humidity Control Adjustment ................................4
Defrost Cycle ........................................................4
Fan Operation ......................................................4
7. 7.1 7.2 7.3 7.4 7.5 Maintenance ........................................................4
Air Filters ..............................................................4
Cleaning Pre-filter ................................................4
Pleated Filter ........................................................5
Removing Filters ..................................................5
Installing Filters ....................................................5
8. 8.1 8.2 8.3
8.4
Service .................................................................5
Technical Description ...........................................5
Troubleshooting ....................................................5
Refrigerant Charging.............................................6
Compressor/Capacitor Replacement.....................6
9. 10. Replacement Parts/Accessories ...........................6
Wiring Diagram ....................................................6
Warranty ..............................................................7
• When changing filters, do not stick fingers or other objects
in the unit.
• Do not restrict airflow in to or out of the unit. This may
cause the unit to overheat.
• The unit should never be serviced or cleaned while it is
plugged in.
• Do not sit or stand on the unit, or use as a shelf or table.
• Before leaving the unit unattended, ensure children do not
have access to the equipment. Do not allow children to play
with or near the unit or in its air flow.
• The unit is designed to be installed indoors only.
• No user serviceable components. Contact installer or call
1-800-533-7533 for all repair or warranty needs.
Read the installation, operation and maintenance instructions
carefully before installing and using this unit. Proper
adherence to these instructions is essential to obtain
maximum benefit from your Santa Fe dehumidifier.
Read and Save These Instructions
WARNING! — This symbol means important
instructions. Failure to heed them can result in serious
injury or death.
CAUTION! — This symbol means important
instructions. Failure to heed them can result in injury or
material property damage.
1. Intended Application(s)
The Santa Fe Compact2 is intended for use in crawlspaces
or basements: however, the unit can be placed in almost
any residential setting where dehumidification is desired.
Use in non-residential applications and pool areas may void
warranty.
Precautions
• Do not operate the Santa Fe Compact2 with a cut or
frayed power cord.
The Santa Fe Compact2 is designed to operate in
temperatures between 49° and 95°F. This unit works most
effectively between 56° and 95°.
• Do not unplug the unit by pulling on the cord. Grasp the
plug firmly and pull it out of the wall socket or power
receptacle.
In order to efficiently control humidity levels, the area in
which the dehumidifier is to be operated must be free of
water intrusion or excessive fresh (outside) air infiltration.
Before installing the Santa Fe Compact2, water intrusion and
air infiltration problems should be addressed.
• Always use a grounded outlet.
• Never operate electrical equipment near or in standing
water.
• Do not stick your fingers or other objects through the
safety grill.
2. Registrations
The Santa Fe Compact2 conforms to UL STD 474 and CSA
standard C22.2 No. 92.
2
Santa Fe Compact2 Installer’s & Owner’s Manual
SANTA FE COMPACT2 INSTALLER'S AND OWNER'S MANUAL
3. Specifications
5. Installation
5.1 Safety Precautions
• Do not install the Santa Fe Compact2 with the intake or
exhaust of the unit within 1' of a wall or other obstruction.
Part Number:4033600
Blower:
150 CFM @ 0.0" WG
Power:
580 watts @ 80°F and 60% RH
Supply Voltage:
115 volt – 1phase – 60 Hz
Current Draw:
5.1 amps
Operating Temp.:
49°F Min., 95°F Max.
Sized for:
1,800 Sq. Ft. - Typical
Miniumum Performance at 80°F and 60% RH
Water Removal: 70 Pints/Day
Efficiency:
5.0 Pints/kWh
Energy Factor:
2.4 L/kWh
• Do not place the unit where curtains or debris can be drawn
onto the intake and restrict airflow.
• Do not operate in standing water or place the unit near open
water.
5.2 Location
The Santa Fe Compact2 can be installed in a variety of locations
to meet the dehumidification needs, but should be installed
directly in the area to be dehumidified. Other considerations
include:
Air Filter: MERV-8, Standard Pleat
Size:9" x 11" x 1"
Power Cord:
9', 115 VAC, Ground
1.Providing access to a 115 VAC power outlet (9' power cord is
provided).
Drain Connection: 3/4" Threaded Female NPT
Drain Hose: 5/8" ID x 8' Direct Gravity Drain Hose
Refrigerant Type: R410A (Refer to manufacturers label
for more information)
Refrigerant Amount: 15 oz.
Dimensions:Unit Shipping
Width:12"
18"
Height:12" 18"
Length:21" 27"
Weight:
55 lbs
64 lbs
2.Locating near a suitable drain (8' drain hose included).
3.The unit is designed to operate while level. If the unit is
placed on an unlevel surface, refer to section 4.1. Failure to
level the unit may result in leakage or improper drainage.
4.The unit should be hung from the floor joists if there is
any possibility of flooding. A flooded unit is not covered
by warranty.
WARNING!
5.3 Electrical Requirements
The Santa Fe Compact2 plugs into a common grounded outlet
on a 110-120 VAC 15-Amp circuit. While operating, it draws
5.1 amps @ 80°F, 60% RH and 4.5 amps @ 70°F, 50% RH.
Use of a ground fault circuit interrupter (GFCI) protected circuit
is recommended. The unit should not be used in areas prone to
flooding.
4. Unit Assembly
4.1 Installing Feet
Included with your Santa Fe Compact2 are four leveling feet.
It is important to level the unit for proper draining. Do not
install the feet if you are using the optional hang kit.
Adjusting Leveling Feet
1. Lay down a protective pad (pillow, blanket, etc.).
2.Carefully turn unit onto side.
3. Install leveling feet and adjust to the desired position.
4. Carefully bring unit to upright position.
5.Repeat steps 1-4 until unit is capable of proper drainage
as described in section 5.2.3 of this manual.
6.Wait a minimum of 10 minutes before operating.
5.4 Condensate (Water) Removal
The Santa Fe Compact2 drains via gravity, therefore, it does not
have the ability to push condensate (water) upwards. The drain
hose must run down towards the drain location. Condensate
can be drained by using the 5/8” clear vinyl hose and the 3/4”
threaded adapter provided. Ensure the threaded adapter is
threaded in tightly.
CAUTION!
CAUTION!
The Santa Fe Compact2 requires a drain trap. Creating a drain
trap allows a small amount of water to build up in the trap area
of the clear hose. This prevents air from back flowing through
the hose and into the dehumidifier; essentially causing the unit
to backflow water out of the corners of the machine. Position
the trap in the hose approximately 8"-10” from the dehumidifier and make sure the highest point of the trap is still at least
2”below the black drain port adapter on the dehumidifier. If the
highest point of the trap is above the drain port, water will back
Note: Operating the unit immediately after bringing it to an
upright position can possibly damage the compressor. A
minimum of 10 minutes is needed to allow the compressor
oil to return to it’s reservoir for lubrication.
4.2 Drain Hose
Install the threaded drain hose fitting into the lower right hand
side, on the front of the machine. Place drain hose end on drain
port until fully seated. Refer to Section 5.2.3 regarding proper
drainage.
3
Santa Fe Compact2 Installer’s & Owner’s Manual
SANTA FE COMPACT2 INSTALLER'S AND OWNER'S MANUAL
flow into the dehumidifier. Check the hose regularly to ensure
water is draining properly.
The dehumidifier will run continuously until the RH is
reduced to the humidity control dial setting. It is not
recommended to set the humidity control to “dry” in rooms
under 65°; doing so will result in long periods of ineffective
dehumidifier run time.
Several trap options include:
Pretzel Loop
To turn unit on, turn the humidity dial clockwise to the
recommended “NORMAL” position and set fan control to “FAN
AUTO.” To turn the unit off, turn the humidity dial counter
clockwise to the “OFF” position and set fan control to “FAN
AUTO.”
Standard Loop
Floor Bend
The Humidity Alert™ (4026208) is
available to accurately monitor humidity
levels. Please contact your dealer or call
1-800-533-7533 to order.
PVC Trap
6.2 Defrost Cycle
This product includes a defrost thermostat. This feature
prevents internal damage caused by excessive frost forming
within the unit. When the unit is experiencing excessive frost
the system will stop dehumidfying and the fan will run until
normal operating conditions are present.
PVC materials available from
your local hardware store.
For additional information on how to create a proper trap,
see our instructional video at:
www.Santa-Fe-Products.com/draintrap
Use care to keep the hose as flat to the floor as possible
after your trap is in place. Be sure the hose is not kinked or
otherwise restricted so water can pass through the hose
freely. Improper installation of the drain hose may result in
water leakage.
6.3 Fan Operation
Turning the fan switch “FAN ON” will cause the unit’s internal
blower to run continuously, whether the unit is dehumidifying
or not. This function is desirable if the unit is used for air
circulation or filtration. Turning the fan switch to “FAN AUTO”
will cause the unit’s internal blower to run only while the unit
is dehumidifying.
If the Santa Fe Compact2 is located too far from the floor
drain and the provided hose does not reach, you may use a
1/2” PVC rigid pipe to extend the drain. Rigid PVC tubing is
readily available from your local hardware store. Be sure the
extension is at a down-word slope to the drain.
7. Maintenance
CAUTION!
An optional condensate pump kit may be installed if lift is
required to remove condensate. To order, contact your local
dealer or visit our website at www.santa-fe-products.com.
You may also reach us by phone at (800) 533-7533.
NOTE: Do not operate the unit without the proper filters.
The heat exchange coils inside the unit could become
clogged, resulting in a loss of effectiveness and/or
efficiency and may require disassembly to clean.
6. Operation
7.1 Air Filters
The Santa Fe Compact2 is equipped with a standard MERV8 65% 1" pleated fabric filter and a 1/4" aluminum framed
pre-filter. Operating the unit with a dirty or obstructed filter
will reduce dehumidifier capacity and efficiency, and may
cause the compressor to cycle on and off unnecessarily.
Approximate Humidity Levels Per Setting
“Drier” 35% to 45% Relative Humidity
“Normal”45% to 55% Relative Humidity
(Recommended for most applications)
“Humid” 55% to 65% Relative Humidity
7.2 Cleaning Pre-filter
Check filter every six months. Clean and/or replace when
filters are visibly dirty. Replacement filters can be ordered
from your dealer or by calling 1-800-533-7533.
6.1 Humidity Control Adjustment
The humidity control is an adjustable switch that turns
the dehumidifier on and off. It turns on when the relative
humidity (RH) rises to the dial set point. It turns off when the
RH is within ±5% of the set point.
The 1/4" washable pre-filter should not to be discarded.
Inspect for debris, dirt, or other obstructions. Wash the 1/4"
4
Santa Fe Compact2 Installer’s & Owner’s Manual
SANTA FE COMPACT2 INSTALLER'S AND OWNER'S MANUAL
pre-filter every time the 1" pleated fabric filter is replaced.
To clean the 1/4" pre-filter, remove filter from the unit, rinse
the 1/4" pre-filter in water with the water flowing through
the aluminum support mesh side. Allow the filter to dry
completely before reinstalling. Reinstall per section 7.5.
high pressure refrigerant gas is routed from the compressor
to the condenser coil. The refrigerant is cooled and
condensed by giving up its heat to the air that is discharged
from the dehumidifier. The refrigerant liquid then passes
through capillary tubing which cause the refrigerant pressure
and temperature to drop. It next enters the evaporator coil
where it absorbs heat from the incoming air and evaporates.
7.3 Pleated filter
Replace filter every six months per section 7.4-7.5. To order
filters contact your dealer or call 1-800-533-7533.
The evaporator operates in a flooded condition, which means
that all the evaporator tubes contain liquid refrigerant during
normal operation. A flooded evaporator should maintain
constant pressure and temperature across the entire coil,
from inlet to outlet. The mixture of gas and liquid refrigerant
enter the accumulator after leaving the evaporator coil. The
accumulator prevents any liquid refrigerant from reaching the
compressor. The compressor evacuates the cool refrigerant
gas from the accumulator and compresses it to a high
pressure and temperature gas to repeat the process.
CAUTION!
NOTE: Failure to follow filter handling instructions may
result in improper function of the dehumidifier and cause
premature filter wear or unit damage.
7.4 Removing Filters
1. R
emove the 1/4" pre-filter by gently pulling on the bottom
of the filter frame.
2. Remove the 1" pleated fabric filter by gently pulling on
the bottom of the filter frame.
8.2 Troubleshooting
FOR THE HOMEOWNER:
n If the unit does not work properly, please check the
following:
— Is the unit unplugged?
— Is power to outlet on? (check switch, if applicable)
— Is circuit breaker tripped?
— Is humidity control set? (turn to “ON”)
— Is air flow restricted? (check air filters and grill)
If none of the above, call dealer or 1-800-533-7533.
7.5 Installing Filters
1.Angle the top of the filter and gently slide 1" pleated filter
into filter slot. Do not force. If resistance is felt, check
alignment for obstructions or debris inside the filter
housing.
2.Angle the top of the filter and gently slide 1/4" pre-filter in
front of 1" pleated filter. Do not force. If resistance is felt,
check alignment for obstructions or debris inside the
filter housing.
FOR THE INSTALLING PROFESSIONAL:
n No dehumidification. Neither blower, nor compressor run
with fan switch AUTO.
1.Unit unplugged or no power to outlet, circuit breaker
tripped.
2. Humidity control set to “Humid” setting.
3.Loose connection in internal wiring.
4. Humidity control is defective.
5. Defective compressor relay.
8. Service
n No
dehumidification. Compressor does not run but
blower runs with fan switch AUTO and humidity control
turned to ON.
1. Defrost thermostat open, ambient temperature too low.
2. Loose connection in compressor circuit.
3. Defective compressor overload.
4. Defective compressor or compressor run capacitor.
WARNING!
Servicing the Santa Fe Compact2, with its high pressure
refrigerant system and high voltage circuitry presents a
health hazard which could result in death, serious bodily
injury, and/or property damage. Only qualified service
people should service this unit.
8.1 Technical Description
The Santa Fe Compact2 uses a refrigeration system similar
to an air conditioner’s to remove heat and moisture from
incoming air and add heat to the air that is discharged. Hot,
n Blower
runs with fan switch AUTO but compressor
cycles on & off.
1. Low ambient temperature and/or humidity causing unit
to cycle through defrost mode.
5
Santa Fe Compact2 Installer’s & Owner’s Manual
SANTA FE COMPACT2 INSTALLER'S AND OWNER'S MANUAL
9. Replacement Parts
2. Defrost thermostat defective.
3. Defective compressor overload.
4. Defective compressor.
5. Dirty air filter(s) or air flow restriced.
4025560 On/Off Switch
1970010 25A Relay
4027163 15A Relay
4029568 Compressor Overload
4021495 Control Knob
4025577 Clear Hose
4026221 Leveling Foot
4029567 Compressor
4027172 Humidity Control
4033032-03 Run Capacitor
4025569 Hose Adaptor
4033031-03 Fan Capacitor
4033358-02 Coil Set
4031384Impeller
4031376
Defrost Thermostat
n Blower
does not run with fan switch in either position.
Compressor runs briefly but cycles on and off.
1. Loose connection in blower circuit.
2. Obstruction prevents impeller rotation.
3. Defective blower.
4. Defective blower switch.
n Evaporator
coil frosted continuously, low dehumidifying
capacity.
1. Dirty air filter or air flow restricted.
2.Defrost thermostat defective.
3. Low refrigerant charge.
If none of the above has fixed the issue, call your dealer
service department or 1-800-533-7533.
Accessories
8.3 Refrigerant Charging
4027168Pre-Filter
4028524
Pre-Filters 12-Pack
4029748 MERV 8 Filter (9"x11"x1")
4030421
MERV 8 Filters 4-Pack + 1 Pre-Filter
4030422
MERV 8 Filters 12-Pack
4030671
MERV 11 Filter (9"x11"x1")
4027418
MERV 11 Filters 4-Pack + 1 Pre-Filter
4030733
MERV 11 Filters 12-Pack
4030113
Pump Kit
4028616
Caster Kit
4029908
Hang Kit
4030426
Duct Kit, Supply & Return
4030203
Duct Kit, Supply Only
4030204
Duct Kit, Return Only
4027415
8" Flex Duct 25'
4020177
8" Flex Insulated Duct 25'
4020175
Remote Dehumidistat
If the refrigerant charge is lost due to service or a leak, a new
charge must be accurately weighed in. If any of the old charge is
left in the system, it must be recovered before weighing in the new
charge. Refer to the unit nameplate for the correct charge weight
and refrigerant type.
8.4 Compressor/Capacitor Replacement
This compressor is equipped with a two terminal external
overload and a run capacitor, but no start capacitor or relay.
CAUTION!
CAUTION-ELECTRICAL SHOCK HAZARD: Electrical power
must be present to perform some tests. These tests
should be performed by a qualified service person.
To order, contact your dealer
or call 1-800-533-7533.
10. Wiring Diagram
COMPRESSOR
RELAY
BLK-5
BLK-14
GRN-1
DEFROST
SWITCH
BLK-20
WHT-3
BLK-19
BLU-17
DEHUMIDISTAT
COMPRESSOR
C
YEL-12
COMPRESSOR
CAPACITOR
WHT-2
S
R
RED-11
BLU-17
BLK-21
BLK-14
N.C.
ORG-18
1 - AUTO
2
BLK-15
GRN-16
N.O.
BLK-6
COM
COIL
BLK-21
FAN RELAY
3 - ON
FAN SWITCH
FAN
BLU-10
WHT-4
BLK-8
BRN-13
GRN-7
FAN
CAPACITOR
4032712
6
Santa Fe Compact2 Installer’s & Owner’s Manual
Limited Warranty
Limited Warranty. Therma-Stor, LLC (“Therma-Stor”) warrants as
follows: (i) the Santa Fe Compact dehumidifier (“Product”) will be free
of material defects in workmanship or materials for a period of one
(2) year (“Two-Year Warranty”) following the date of initial purchase
of such Product by an original customer purchasing from ThermaStor or an authorized reseller (“Customer”); and (ii) the Product’s
condenser, evaporator, and compressor will be free of material
defects in workmanship or materials for a period of five (5) years
following the date of initial purchase of such Product by a Customer.
Limitation of Remedies. CUSTOMER’S SOLE AND EXCLUSIVE
REMEDY UNDER THE ABOVE LIMITED WARRANTY AND THERMASTOR’S ENTIRE LIABILITY THEREUNDER, SHALL BE, AT THE SOLE
OPTION OF THERMA-STOR, REPLACEMENT OR REPAIR OF SUCH
PRODUCT OR ITS COMPONENTS (“COMPONENTS”) BY THERMASTOR OR THERMA-STOR’S AGENTS ONLY. REFRIGERANT, PIPING,
SUPPLIES, TRANSPORTATION COSTS, LABOR COSTS INCURRED
IN REPAIR OR REPLACEMENT OF SUCH COMPONENTS ARE NOT
INCLUDED. THIS DISCLAIMER AND EXCLUSION SHALL APPLY
EVEN IF THE EXPRESS WARRANTY AND LIMITED REMEDY SET
FORTH HEREIN FAILS OF ITS ESSENTIAL PURPOSE. CUSTOMER
ACKNOWLEDGES THAT NO REPRESENTATIVE OF THERMA-STOR OR
OF ITS AFFILIATES OR RESELLERS IS AUTHORIZED TO MAKE ANY
REPRESENTATION OR WARRANTY ON BEHALF OF THERMA-STOR
OR ANY OF ITS AFFILIATES OR RESELLERS THAT IS NOT IN THIS
AGREEMENT. Notwithstanding the above, during the term of the
Two-Year Warranty only, Therma-Stor will provide, free of charge to
Customer, all Components and labor (except costs related to removal
and installation of Product) required to fulfill its obligations under such
Two-Year Warranty.
Disclaimer of Warranties. EXCEPT FOR ABOVE LIMITED
WARRANTY, WHICH IS THE SOLE AND EXCLUSIVE WARRANTY
PROVIDED WITH RESPECT TO THE PRODUCT AND ITS COMPONENTS,
THERMA-STOR HEREBY DISCLAIMS ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE.
Warranty Limitations. The foregoing limited warranty extends only
to a Customer and shall be null and void upon attempted assignment
or transfer. A “defect” under the terms of the limited warranty shall
not include problems resulting from Customer’s or Customer’s
employees’, agents’, invitees’ or a third party’s misuse, improper
installation, improper design of any system in which the Product
is included, abuse, lack of normal care, failure to follow written
instructions, tampering, improper repair, or freezing, corrosion, acts
of nature or other causes not arising out of defects in Therma-Stor’s
workmanship or material. If a Product or Component is replaced
while under warranty, the applicable limited warranty period shall
not be extended beyond the original warranty time period. The
limited warranty does not cover any costs related to changes to a
Product or Component that may be required by any codes, laws, or
regulations that may become effective after initial purchase of the
Product by Customer.
7
Customer Responsibilities. As a further condition to obtaining
warranty coverage hereunder, the Customer must send a valid
warranty claim to Therma-Stor such that Therma-Stor receives
such claim prior to the end of the applicable warranty period.
Therma-Stor shall have no obligation hereunder with respect to
any claim received by Therma-Stor after the expiration of the
applicable warranty period. As a further condition to obtaining
warranty coverage hereunder, the Customer must present forms of
invoices evidencing proof of purchase of a Product. If such invoices
do not clearly indicate the date of initial purchase by a Customer,
the applicable Product’s date of manufacture will be used instead
of the date of initial purchase for the purpose of calculating the
commencement of the applicable warranty period. Warranty service
must be performed by Therma-Stor or a servicer authorized by
Therma-Stor. In order to obtain warranty service, the Customer
should call Therma-Stor at 1-800-533-7533 and ask for the
Therma-Stor Products Service Department, which will then arrange
for applicable warranty service. Warranty service will be performed
during customary, daytime working hours. If the Product must be
shipped for service, Customer shall be solely responsible for properly
packaging the Product, for all freight charges, and for all risk of loss
associated with shipment.
Limitation of Liability. IN NO EVENT SHALL THERMA-STOR,
IN CONNECTION WITH THE DESIGN, SALE, INSTALLATION, USE,
REPAIR, REPLACEMENT OR PERFORMANCE OF ANY PRODUCT,
COMPONENT, PART THEREOF OR WRITTEN MATERIAL PROVIDED
THEREWITH, BE LIABLE, TO THE EXTENT ALLOWED UNDER
APPLICABLE LAW, UNDER ANY LEGAL THEORY FOR ANY SPECIAL,
DIRECT, INDIRECT, COLLATERAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND. NOTWITHSTANDING THE ABOVE LIMITATIONS AND
WARRANTIES, THE SOLE AND EXCLUSIVE LIABILITY OF THERMASTOR, REGARDLESS OF THE NATURE OR THEORY OF THE CLAIM,
SHALL UNDER NO CIRCUMSTANCES EXCEED THE PURCHASE PRICE
OF THE PRODUCT, COMPONENT OR PART UPON WHICH THE CLAIM
IS PREMISED.
Applicable Law and Venue. ANY ARBITRATION, ENFORCEMENT
OF AN ARBITRATION OR LITIGATION RELATED TO THE PRODUCT
WILL BE BROUGHT EXCLUSIVELY IN DANE COUNTY, WISCONSIN,
AND CUSTOMER CONSENTS TO THE JURISDICTION OF THE
FEDERAL AND STATE COURTS LOCATED THEREIN, SUBMITS TO
THE JURISDICTION THEREOF AND WAIVES THE RIGHT TO CHANGE
VENUE. CUSTOMER FURTHER CONSENTS TO THE EXERCISE OF
PERSONAL JURISDICTION BY ANY SUCH COURT WITH RESPECT TO
ANY SUCH PROCEEDING.
Miscellaneous. If any term or condition of this Limited Warranty
is found by a court of competent jurisdiction to be invalid, illegal or
otherwise unenforceable, the same shall not affect the other terms
or conditions hereof or thereof or the whole of this Limited Warranty.
Any delay or failure by Therma-Stor to exercise any right or remedy
will not constitute a waiver of Therma-Stor to thereafter enforce
such rights.
1-800-533-7533. | www.santa-fe-products.com