PROFESSIONAL
SERIES
Owner’s Guide
For Models:
CASEC
&
CA2LCD5
Deluxe Vehicle Security and
Keyless Entry System
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the configuration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
2017 Voxx Electronics Corporation. All rights reserved.
1
Table of Contents
Using Your Remote Control..................................................................... 3
Arming the Security System............................................................... 3
Passive Arming Bypass...................................................................... 3
Bypassing the Shock Sensor............................................................. 3
Hidden Alarm Function....................................................................... 3
Disarming the Security System.......................................................... 3
Two Stage Door Unlock (optional)...................................................... 4
Activating Trunk Release (optional).................................................... 4
Activating AUX 1 (optional)................................................................. 4
Entering AUX Mode and Activating Additional AUX Outputs.............. 4
Using the Progressive Car Finder Feature......................................... 5
Using the Personal Protection Alarm.................................................. 5
Programmed Transmitter Notification................................................. 5
Valet Mode......................................................................................... 5
User Selectable Notification Chirps.................................................... 5
User Selectable LED.......................................................................... 6
Manually Overriding the Security System.......................................... 6
Carjack Mode..................................................................................... 6
Status LED, Light Flashes and Siren/Horn Indications........................ 7
Additional 2-Way LCD Remote Control Functions................................ 8
LCD Remote Control ICON’s................................................................. 10
Remote Control Buttons & Functions.................................................. 11
Replacing Remote Control Batteries.................................................... 13
Warranty Information............................................................................. 14
2
caSEC/ca2LCD5 4280835 Owners revA
Using Your Remote Control
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the
button. The
parking lights will flash 2 times, indicating the system is armed, has locked the doors
(if equipped and connected) and activated the starter disable feature. The LED status
indicator will blink steadily, once per second.
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the
system requires a second press of the
button to activate an audible arming
response from the vehicle.
Passive Arming Bypass
If passive arming is enabled on your system, while the system is disarmed, press
+
, the system will respond with 1 chirp and the LED will turn on. The security
system will remain in this temporally bypassed state for as long as you wish. To exit
passive bypass, press the
or
button and the system will return to normal status.
Bypassing The Shock Sensor
To arm the system and ignore the shock sensor press
button, then within 5
seconds press
+
, the system will respond with 1 long chirp.
NOTE: The system will only change the shock sensor setting for one arm cycle and
will be defaulted back to normal operation the next time the system is armed.
Hidden Alarm Function
Press the
button first, within 3 seconds press the
button to activate the hidden
alarm function. The security system will arm with “Hidden Alarm Function” in which the
siren / horn will be silenced if the system is triggered.
Disarming the Security System
To disarm the system press the
button. The parking lights will flash 1 time,
indicating the system is disarmed and has unlocked the doors (if equipped and
connected).
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the
system requires a second press of the
button to activate an audible disarming
response from the vehicle. If your system is set up for 2 step unlock, a third press of
unlock will activate the audible response.
* Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more
than 2 seconds.
2017 Voxx Electronics Corporation. All rights reserved.
3
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the
button one time will unlock
only the driver’s door. Press
again within three seconds to unlock the remaining
doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the
seconds will open the vehicle’s trunk or hatch.
button for 3
Activating the AUX 1 Output (Optional)
If this feature is enabled on your system, pressing the
and
buttons
simultaneously will activate an optional feature. This feature can be programmed for a
wide range of functions like power window or sunroof automation, please consult your
installing dealer to determine the functionality of your system.
Entering AUX Mode and Activating the Additional AUX 2 - 5 Outputs (Optional)
To access the additional AUX outputs, AUX 2, AUX 3, AUX 4, and AUX 5, you must
first enter the transmitters AUX Mode. This will “shift” the functions of the transmitter
buttons from their standard operation to control of the AUX outputs.
4
AUX Mode - 4 button transmitter: Press and Hold
and
for 2 seconds, the transmitter LED will flash 1 time. AUX Mode will remain active for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by pressing
and
again for 2 seconds, the transmitter LED will flash 2 times to confirm exit.
AUX Mode - LCD 5 Button transmitter: Press and Hold
for 2 seconds, the transmitter LCD screen will display “AU”. AUX Mode will remain active for 15 seconds. AUX Mode will exit after 15 seconds of inactivity or by pressing
again for 2 seconds.
Activating outputs while in AUX Mode:
AUX 2: Press and Hold
for 3 seconds.
AUX 3: Press and Hold
for 3 seconds.
AUX 4: Press and Hold
for 3 seconds.
AUX 5: Press and Hold
for 3 seconds.
caSEC/ca2LCD5 4280835 Owners revA
Using the Progressive Car Finder Feature
Press the
button to locate your vehicle. The system will flash the parking lights
and sound 5 times at low volume, increasing in volume each time the button is
pressed.
Using the Personal Protection Alarm (Panic)
Press and hold the
button for 3 seconds to activate the personal protection alarm.
During panic mode, the normal function of the transmitter buttons will be suspended.
The transmitter’s
and
buttons can be used to lock and unlock the door (if the
option is installed). To stop the alarm, press and hold the
button on the transmitter
again for 3 seconds. The system will automatically stop after 30 seconds.
Programmed Transmitter Notification
As a security precaution each time the vehicle’s ignition is turn on the status LED
light with flash the number of transmitters programmed into the system. This helps
to identify unauthorized transmitters from accessing your vehicle. If you believe an
unauthorized transmitter has been programmed to your system, contact your installing
dealer for assistance.
Valet Mode
When valet mode is activated the status LED will light solid, and all security functions will be disabled. To enter or exit valet mode simply follow the steps outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the programming/valet button.
3. The LED will turn on solid when valet mode is active
4. Release the programming/valet button.
User Selectable Notification Chirps
System ARM/DISARM chirps can be toggled ON or OFF without entering the
programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
2017 Voxx Electronics Corporation. All rights reserved.
5
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is Armed/
Locked and can be toggled ON or OFF without entering the programming feature
banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and release the valet/programming button 3 times. The system will respond with 1 chirp for ON or 2 chirps for OFF.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is necessary,
since you will need the ability to operate your vehicle if the transmitter is lost or its
battery fails. To by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the ON position.
3. Within 10 seconds, press and release the valet push button switch.
The alarm system will stop sounding and enter the (by-passed) mode. You can now
start and operate the vehicle normally.
Carjack Mode (Anti-Hijack Mode)
This feature must be turned on in system programming, please consult your installing
dealer.
Triggering Carjack mode: While the ignition is ON and press and hold
+
for 2
seconds, the parking lights will flash 1 time and the system will act as follows;
1. 50 seconds after being triggered the siren will chirp for 15 seconds, during this 15 seconds you will be alerted to push the valet button to turn off Carjack mode. If Carjack mode is not turned off at this time it will advance to the next step.
2. Following the 15 second chirps (total time now 65 seconds) the siren will go into full sound and the parking lights will start flashing.
3.
90 seconds after trigger in, addition to the siren and parking lights, the system will activate the starter kill. THE SYSTEM WILL REMAIN IN THIS STATE UNTIL THE BATTERY IS DEPLETED.
OVERRIDE THE SYSTEM TO TURN OFF CARJACK MODE: Turn the ignition OFF
then On and press the valet button within 10 seconds.
6
caSEC/ca2LCD5 4280835 Owners revA
Status LED, Light Flashes, and Siren/Horn Indications
Status LED Flash Indications
LED Flashes
Function
OFF
Disarmed
Slow Flash
Armed
Fast Flash
Passive Arming Countdown
ON (Solid)
Valet Mode
2 Flashes
Zone 2 Trigger, Hood / Trunk
3 Flashes
Zone 3 Trigger, Door
4 Flashes
Zone 4 Trigger, Shock Sensor
5 Flashes
Zone 5 Trigger, Ignition
Siren/Horn Chirp Indications
Chirps
1
Function
Disarm
2
Arm
3
Door Ajar Upon Arming
4
Disarm / Triggered
5
Car Find
Parking Light Flash Indications
Flashes
1
Function
Disarm
2
Arm
3
Disarm / Triggered
5
Car Find
2017 Voxx Electronics Corporation. All rights reserved.
7
Additional 2-Way LCD Remote Control Functions
Additional Features of the Optional 2 Way LCD Remote Control
Check Vehicle Status
Press and release
2 times then press
display the current status of the vehicle.
within 3 seconds, the transmitter will
Display Illumination
Press and hold the
button for 1 second. The display will illuminate for 5 seconds.
Melody / Vibration Mode
To have the remote control vibrate, play a melody tone or both each time it receives a
response from the vehicle press and release
then press and hold
for 2
seconds.
Button Beeps
To toggle button beeps on or off press and release
seconds.
then press and hold
for 2
Battery Save Mode
While in POWER SAVE MODE the 2-way LCD transmitter will NOT look for any
incoming signals from the main unit until a button is pressed. The LCD screen will
display SAVE to indicate that power save mode is ON. To enter power save mode
press and hold
for 5 seconds.
Clear Flashing Icons and Melody Sound
Press the
button 3 times within 3 seconds. This will clear the melody sound and
flashing icons on the LCD screen.
Stopping LCD Trigger Melody
To stop the alarm trigger melody if the system has been triggered WITHOUT
disarming the system, press any button one time only, this will not send a command to
the vehicle at this time and the alarm will continue to sound.
8
caSEC/ca2LCD5 4280835 Owners revA
Button Lock
Press and release
then press hold the
for 2 seconds to toggle the button lock
on or off. When the button lock is active, the remote control will beep/vibrate 2 times
when a button is pressed indicating it is locked.
Illumination
Press and release
2 times then press and hold
for 2 seconds to toggle
illumination on or off. When on, the display will illuminate when it receives or sends a
command.
2 Car Mode
To control a second security system enter 2 car mode by pressing
then press
and
together for 3 seconds. When the icon appears on the transmitter’s LCD
screen it will control the second security system. Use the same method to exit 2 car
mode and resume control of the original vehicle’s security system.
NOTE: A second security system must be installed and the LCD transmitter must be
learned to it before this feature will operate the additional system.
Parking Meter Countdown
The parking meter countdown timer has 6 preset times, to access the preset times
and begin countdown press and release
then press and hold
for 2 seconds,
each additional press of
will increase the countdown time.
Adjusting the Clock and Timer Settings
The clock, alarm clock and programmable countdown timer are accessed through the
Function Menu. Press and hold
for 3 seconds to access the function menu, once
you have accessed the feature menu press and release
to scroll through each
feature and follow the steps below to adjust the settings for each. Press and hold
for 2 seconds to exit the menu.
Clock Hour
Press
to increase or
to decrease
Clock Minute
Press
to increase or
to decrease
Alarm Clock Hour
Press
to increase or
to decrease
Alarm Clock Minute
Press
to increase or
to decrease
Alarm Clock ON / OFF
Press
to turn ON or
to turn OFF
Countdown Timer Hour
Press
to increase or
to decrease
Countdown Timer Minute
Press
to increase or
to decrease
Countdown Timer ON / OFF Press
to turn ON or
to turn OFF
2017 Voxx Electronics Corporation. All rights reserved.
9
LCD Remote Control ICON’s
LOCK
UNLOCK
SYSTEM ARMED
VALET MODE
TRANSMITTING
IGNITION ON/TRIGGER
TRUNK TRIGGER
DOOR TRIGGER
HOOD TRIGGER
FULL SHOCK TRIGGER
SYSTEM TRIGGER
TIME COUNT DOWN
BATTERY INDICATOR
BATTERY SAVE MODE
VIBRATE/SILENT MODE
MELODY MODE
2 CAR MODE
TIME DISPLAY
ALARM CLOCK
AUX MODE
AUX 1 OUTPUT
AUX 2 OUTPUT
AUX 3 OUTPUT
AUX 4 OUTPUT
AUX 5 OUTPUT
10
caSEC/ca2LCD5 4280835 Owners revA
Remote Control Buttons & Functions
4-Button
Transmitter
Lock
Lock
Unlock
Car Find /
Panic
Trunk
X
Operation Method
Press and Release
Unlock
X
Press and Release
2 Step Unlock
X
Press and Release 2 times
Trunk
X
Push and Hold (3 Sec)
Car Finder
X
Press and Release
Panic
X
Push and Hold (3 Sec)
AUX 1
X
Shock Bypass
X
X
Press and Release Lock then
Press Lock + Car Find
Hidden Alarm
X
X
Press and Release Car Fnd then
Press Lock
X
Press and Release
Passive Arming
Bypass
X
X
Push and Hold (3 Sec)
AUX 2, 3, 4, 5 - Access in AUX Mode
Enter AUX Mode
AUX 2
AUX 3
AUX 4
X
X
X
Press and Hold Find + Trunk
Transmitter LED flashes 1 time
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
X
AUX 5
2017 Voxx Electronics Corporation. All rights reserved.
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
11
LCD 5-Button
Transmitter
Lock
Lock
Unlock
Car Find /
Panic
Trunk
Function Operation Method
X
Press and Release
Unlock
X
Press and Release
2 Step Unlock
X
Press and Release 2 times
Trunk
X
Push and Hold (3 Sec)
Car Finder
X
Press and Release
Panic
X
Push and Hold (3 Sec)
AUX 1
X
Shock Bypass
X
X
Press and Release Lock then
Press Lock + Car Find
Hidden Alarm
X
X
Press and Release Car Fnd then
Press Lock
X
Press and Release
Passive Arming
Bypass
X
X
Push and Hold (3 Sec)
Menu
X
Press and Release
AUX 2, 3, 4, 5 - Access in AUX Mode
Enter AUX Mode
AUX 2
AUX 3
AUX 4
AUX 5
12
X
X
Press and Hold F for 2 seconds
LCD displays AU
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
X
Push and Hold (3 Sec)
caSEC/ca2LCD5 4280835 Owners revA
Replacing Remote Control Batteries
4 Button Remote Control - Model CAT4M
The batteries inside each remote control should last approximately 1 year under normal
use. When the batteries become weak you will notice the remote control range (the
distance from the vehicle the remote control will work) deteriorate and the small LED on
the remote control will dim. To replace the remote control batteries:
1. Remove 1 screw then disassemble the halves of the remote control by unsnapping the back of the case.
2. Remove the old battery, observing the +/- symbols on the batteries and replace with a new battery.
3. Reassemble the halves of the remote control and reinstall 1 screw.
4. Test operation of the remote control.
2 Way LCD Remote Control - Model CATLCD
The AAA battery inside the 2-way LCD remote control should last approximately 6
months under normal use. When the battery becomes weak you will notice the remote
control range (the distance from the vehicle the remote control will work) deteriorate and
the battery icon on the LCD remote control will show 1 bar or less.
1. Gently slide the battery cover off of the remote control.
2. Remove the old AAA battery, observing the +/- symbols on the battery, and replace with a new AAA battery.
3. Gently slide the battery cover on to the back of the remote control.
4. Test operation of the remote control.
2017 Voxx Electronics Corporation. All rights reserved.
13
LIMITED LIFETIME WARRANTY
Applies to Code Alarm Series Control Modules, Sirens, Sensors, and Relays.
Voxx Electronics Corporation (the Company) warrants to the original purchaser of this
product that should this product or any part thereof, (other than transmitters) under normal use and conditions, be proven defective in material or workmanship during the lifetime of the vehicle, in which it was originally installed from the date of original purchase
such defect(s) will be repaired or replaced with new or reconditioned product, (at the
Company’s option) without charge for parts or repair labor. A transmitter is warranted for
12 months from the date of original purchase.
To obtain repair or replacement within the terms of this Warranty, the product is to
be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to an approved warranty station. This Warranty is not
transferable.
This Warranty does not cover damage to the vehicle’s electrical system or costs
incurred for removal or reinstallation of the product. This Warranty does not cover batteries, broken LCD or OLED display screens, nor apply to any product or part thereof
which, in the opinion of the Company, has suffered or been damaged through alteration,
improper installation, mishandling, misuse, abuse, neglect, accident, or by removal or
defacement of the factory serial number/bar code label(s).
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. IN NO CASE
SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY. No person or representative is authorized to assume for the Company any liability other than expressed
herein in connection with the sale of this product.
The company does not warrant that this product cannot be compromised or circumvented. THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO
EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID
BY PURCHASER FOR THE PRODUCT WITHOUT COST OF INSTALLATION.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations or
exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
Voxx Electronics Corporation, 180 Marcus Blvd., Hauppauge, New York 11788 / 1-800-645-4994
128-9445
14
caSEC/ca2LCD5 4280835 Owners revA
2017 Voxx Electronics Corporation. All rights reserved.
15
Voxx Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PATENTED: www.voxxintl.com/company/patents
16
caSEC/ca2LCD5 4280835 Owners revA