301
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com
OWNERS MANUAL
STANDARD
FRYERS
COUNTERTOP
MODELS
Model F14
F14
F49
F55
F67
F85
F1725
Model F55
Model F85
Model F1725
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
2M-307588 Rev. D M301
120227
LIMITED WARRANTY STATEMENT
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of
defects without charge by a Wells Bloomfield factory
authorized service agency or one of its sub-service
agencies. This service will be provided on customer’s
premises for non-portable models. Portable models (a
device with a cord and plug) must be taken or shipped
to the closest authorized service agency, transportation
charges prepaid, for service. In addition to restrictions
contained in this warranty, specific limitations are shown in
the Service Policy and Procedure Guide. Wells Bloomfield
authorized service agencies are located in principal cities.
This warranty is valid in the United States and Canada and
void elsewhere. Please consult your classified telephone
directory, your foodservice equipment dealer or contact:
Wells Bloomfield, LLC
10 Sunnen Dr., St. Louis MO 63143 USA
phone (314) 678-6314 or fax (314) 781-2714
Unless otherwise specified, all commercial cooking
equipment manufactured by WELLS BLOOMFIELD, LLC is
warranted against defects in materials and workmanship
for a period of one year from the date of original installation
or 18 months from the date of shipment from our factory,
whichever comes first, and is for the benefit of the original
purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY
WARRANTY, EXPRESSED OR IMPLIED IN LAW
OR IN FACT, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR ANY PARTICULAR PURPOSE, AND/OR FOR
DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH WELLS BLOOMFIELD PRODUCTS.
This warranty is void if it is determined that, upon inspection
by an authorized service agency, the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God. It also
does not apply if the serial nameplate has been removed,
or if service is performed by unauthorized personnel.
The prices charged by Wells Bloomfield for its products
for information and other details concerning warranty.
1.
2.
3.
4.
5.
6.
Resetting of safety thermostats, circuit breakers, over
load protectors, and/or fuse replacements are not
covered by this warranty unless warranted conditions are the cause.
All problems due to operation at voltages or phase other than specified on equipment nameplates are not covered by this warranty.
Conversion to correct voltage and/or phase must be the customer’s responsibility.
All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams supplied with the equipment are not covered by this warranty.
Replacement of items subject to normal wear, to
include such items as knobs, light bulbs; and, normal maintenance functions including adjustments of
thermostats, adjustment of micro switches and
replacement of fuses and indicating lights are not
covered by warranty.
Damage to electrical cords and/or plug due to exposure
to excessive heat are not covered by this warranty.
Full use, care, and maintenance instructions supplied
with each machine. Noted maintenance and
preventative maintenance items, such as servicing and cleaning schedules, are customer responsibility.
Those miscellaneous adjustments noted are customer
responsibility. Proper attention to preventative
maintenance and scheduled maintenance procedures will prolong the life of the appliance.
7. Travel mileage is limited to sixty (60) miles from an Authorized Service Agency or one of its sub-service agencies.
8. All labor shall be performed during regular working
hours. Overtime premium will be charged to the buyer.
9. All genuine Wells replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only
to replacement of the defective part(s). Any use of
non-genuine Wells parts completely voids any
warranty.
10. Installation, labor, and job check-outs are not
considered warranty and are thus not covered by this warranty.
11. Charges incurred by delays, waiting time or operating restrictions that hinder the service technician’s ability to perform service are not covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment
in this shipment was carefully inspected and packaged
by skilled personnel before leaving the factory. Upon
acceptance of this shipment, the transportation company
assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill or
express receipt, and that the note of loss or damage is
signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them. This should be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
Wells Bloomfield cannot assume liability for damage or loss
incurred in transit. We will, however, at your request, supply
you with the necessary documents to support your claim.
xi
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
TABLE OF CONTENTS
WARRANTY
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION
OPERATION
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
MAINTENANCE
EXPLODED VIEW & PARTS LIST
WIRING DIAGRAM
PARTS & SERVICE
CUSTOMER SERVICE DATA xi
1
2
3
4
4
6
7
9
10
11
18
25
25
INTRODUCTION
Thank You for purchasing this Wells Bloomfield appliance.
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it
gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly install this appliance, and to use and care for the
appliance in a manner which will ensure its optimum performance.
SPECIFICATIONS
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
MODEL
F14
F49
F55
VOLTS
AMPS
WATTS
POWER SUPPLY CORD
120 VAC 1ø
15A
1.8KW
NEMA 5-15P
208/240 VAC 1ø
208 VAC 1ø
208/240 VAC 1ø
208VAC 1ø
240VAC 1ø
16.4/18.8A
22.1 A
16.6/19.1A
27.7A
24.0A
L1=38.3A
L2=22.1A
L3=22.1A
L1=28.8/33.2A
L2=16.6/19.2A
L3=16.6/19.2A
L1=31.9A
L2=31.9A
L3=31.9A
L1=27.6A
L2=27.6A
L3=27.6A
L1=13.8A
L2=13.8A
L3=13.8A
L1=47.8A
L2=47.8A
L3=47.8A
L1=41.5A
L2=41.5A
L3=41.5A
3.4/4.5KW
4.6KW
3.5/4.6KW
5.75KW
5.75KW
NEMA 6-30P
208VAC 3ø
F67
208/240VAC 3ø
208VAC 3ø
F85
240VAC 3ø
480VAC 3ø
208VAC 3ø
F1725
240VAC 3ø
1
NEMA 6-30P
NOT SUPPLIED
9.2KW
NOT SUPPLIED
6.9/9.2KW
11.5KW
11.5KW
NOT SUPPLIED
11.5KW
17.25KW
NOT SUPPLIED
17.25KW
Fig. 1 Countertop Fryer Features & Operating Controls
F55 Shown - Others are Similar
2
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
FEATURES & OPERATING CONTROLS
PRECAUTIONS AND GENERAL INFORMATION
DANGER: SEVERE BURN HAZARD
Contact with hot oil will cause severe burns. Always wear protective clothing and heat
resistant gloves when operating the fryer or filtering the oil.
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by
qualified service personnel. DO NOT open any access panel that requires the use of
tools. Failure to heed this warning may result in severe electric shock.
WARNING: BURN HAZARD
DO NOT allow water or ice to contact hot oil. DO NOT attempt to cool the oil with
water or ice. The water will boil violently, causing hot oil to foam and splatter.
Contact with splattering or foaming hot oil will cause severe burns.
This appliance is intended for use in commercial establishments
only.
This appliance is intended to prepare food for human consumption.
No other use is recommended or authorized by the manufacturer or its
agents.
Operators of this appliance must be familiar with the appliance use,
limitations and associated restrictions. Operating instructions must be
read and understood by all persons using or installing this appliance.
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Cleanliness of this appliance is essential to good sanitation. Read and
follow all included cleaning instructions and schedules to ensure the
safety of the food product.
Disconnect this appliance from electrical power before performing any
maintenance or servicing.
DO NOT submerge this appliance in water. This appliance is not jet
stream approved. Do not direct water jet or steam jet at this appliance,
or at any control panel or wiring. Do not splash or pour water on, in or
over any controls, control panel or wiring.
Exposed surfaces of this appliance can be hot to the touch and may
cause burns.
The technical content of this manual, including any wiring diagrams,
schematics, parts breakdown illustrations and/or adjustment
procedures, is intended for use by qualified technical personnel.
Any procedure which requires the use of tools must be performed by a
qualified technician.
This manual is considered to be a permanent part of the appliance.
This manual and all supplied instructions, diagrams, schematics, parts
breakdown illustrations, notices and labels must remain with the
appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this
appliance has American sizes on all hardware.
3
CAUTION:
BURN HAZARD
Contact with hot oil may
cause burns. DO NOT fill
fryer beyond MAX OIL line on
frypot.
For disposal of oil use only
a container specifically
designed for the disposal of
hot oil. DO NOT fill hot oil
disposal container beyond
MAX OIL line.
CAUTION:
Risk of
Damage
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance will result if
these instructions are not
followed.
CAUTION:
Hot Surface
Exposed surfaces can be hot
to the touch and may cause
burns.
AGENCY LISTING INFORMATION
This appliance conforms to NSF Standard 4 for sanitation only if
installed in accordance with the supplied Installation Instructions and
maintained according to the instructions in this manual.
This appliance is
240V.
U Listed under UL File E6070 for 120V, 208V and
STD 4
E6070
INSTALLATION
Carefully remove the appliance from the carton. Remove all
protective plastic film, packing materials and accessories from the
Appliance before connecting electrical power or otherwise performing
any installation procedure.
Carefully read all instructions in this manual and the Installation
Instruction Sheet packed with the appliance before starting any
installation.
Read and understand all labels and diagrams attached to the
appliance.
Carefully account for all components and accessories before
discarding packing materials. Store all accessories in a convenient
place for later use.
COMPONENTS
1 or 2 ea. FRYPOT
2 or 4 ea. FRY BASKETS
4 ea. ADJUSTABLE LEGS (except F14)
4 ea. RUBBER FEET (F14 only)
NOTE: DO NOT discard
the carton or other packing
materials until you have
inspected the appliance for
hidden damage and tested it
for proper operation.
Refer to SHIPPING DAMAGE
CLAIM PROCEDURE on the
inside front cover of this
manual.
IMPORTANT:
This installation must comply
with all applicable Federal,
Local and NFPA codes.
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
UNPACKING & INSPECTION
SETUP
Setup the appliance only on a firm, level, non-combustible surface.
Verify local codes for requirements. Concrete, tile, terrazzo or metal
surfaces are recommended. Metal over combustible material may not
meet code for non-combustible surfaces.
Install one adjustable leg at each corner of the fryer by screwing the
leg into the fitting on the bottom. With a spirit level, check that the
appliance is level front-to-back and side-to-side. Verify that the unit
sits firmly on ALL FOUR LEGS or rubber feet.
The lower portions of the legs are adjustable by turning; adjust as
required to level the appliance. All four legs or rubber feet must be
adjusted to firmly contact the counter in order to prevent tipping.
Refer to the Installation Instruction Sheet for required clearances.
Maintain required clearances between the appliance and adjacent
combustible surfaces.
Avoid storing flammable or combustible materials in, on or near the
appliance.
4
Fig. 2 Adjustable Legs
INSTALLATION (continued)
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated electrical components must be performed by a
factory authorized technician.
DO NOT open any access panel which requires the use of tools. Failure to follow this warning
can result in severe electrical shock.
F14 and F49 FRYER ELECTRICAL INSTALLATION
CAUTION:
This fryer is equipped with a cord and plug, and requires a properly
installed matching receptacle. Contact a licensed electrician to install
an appropriate electric circuit and grounded receptacle.
RISK OF
DAMAGE
Fig. 3 Fryer Power Plug and
Receptacle Configuration
Be sure the TEMPERATURE
CONTROL KNOB is turned to the
OFF position, then plug the POWER
CORD into the proper receptacle.
CAUTION:
ELECTRIC
SHOCK HAZARD
F55, F67 and F85 FRYER
ELECTRICAL INSTALLATION
These fryers must be connected directly to the electric circuit. Conduit
and strain relief must be provided by the electrician. Refer to fryer
nameplate for circuit voltage and amperage requirements.
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
DO NOT connect or energize
this appliance until all
installation instructions are
read and followed. Damage
to the appliance will result
if these instructions are not
followed.
Raise the element head, remove the frypot and the cover at the rear
of the fryer to gain access to the terminal block. The electrical inlet is
provided by a knock-out in the rear panel.
If an equipment shutdown interface is required by local fire code,
the flame sensor terminal block may be accessed by removing the
back panel. Replace the jumper of the terminal block with wiring to a
normally closed contact of the building fire management system.
DO NOT connect power to the flame sensor terminal block. Wiring and
contacts must be capable of handling 20 amps.
F67 and F85 fryers are shipped from the factory wired for three phase.
Refer to included wiring diagram for conversion to single phase
operation.
The ground pin of the power
cord plug is part of a system
designed to protect you from
electric shock in the event of
equipment damage.
DO NOT cut the ground pin
from the power cord plug
in order to fit an existing
receptacle;
DO NOT twist a blade of the
power cord plug in order to fit
an existing receptacle.
Contact a licensed electrician
to install an appropriate
electrical circuit and
receptacle.
CAUTION:
ELECTRIC
SHOCK HAZARD
The ground lug of F55,
F67 and F85 fryers must
be connected to a suitable
building electric ground.
IMPORTANT:
Damage due to being
connected to the wrong
voltage or phase is NOT
covered by warranty.
5
OPERATION
DANGER: BURN HAZARD
Contact with hot oil will cause severe burns.
Always wear protective clothing and heat resistant gloves when operating the fryer.
CAUTION:
Normal Operation
Hot Surface
1. a.
b.
Exposed surfaces can be hot
to the touch and may cause
burns.
Be sure the TEMPERATURE CONTROL KNOB is turned to OFF.
Lower the element head into the frypot by pushing back on the BASKET SUPPORT ROD, raising the ELEMENT HEAD SUPPORT ROD, then carefully lowering the elements.
Fig. 3 Temperature Control
Knob (F67)
Fig. 4 Oil Level Marking
NOTE: If the oil temperature
exceeds 440ºF, the hi-limit
safety will shut down the unit,
and light the red TROUBLE
light. To reset:
Allow the oil to cool, then
press the red button on the
back of the element head
until it “clicks” and stays in.
If tripping persists, see
Troubleshooting Suggestions,
page 9.
IMPORTANT: DO NOT overfill the frypot. Cold oil will expand as it heats. Adding too much oil will allow the frypot to overflow during operation.
For best results, always use top grade commercial shortening made specially for frying. Maintain proper oil level in frypot during
operation.
3. Turn the TEMPERATURE CONTROL KNOB to the desired
temperature. The HEAT INDICATOR will glow. When the oil
reaches the desired temperature, the heat indicator will go out.
The heat indicator will go off and on during operation as the
thermostat cycles to maintain temperature.
For best results: DO NOT set temperature control to a temperature setting higher than is required for the food product.
4. Load either or both baskets no more than 1/2 full with food product.
a. DO NOT overload fry baskets. For best results, load baskets uniformly to half full.
b. Using the basket handle, lower the baskets into the hot oil.
c. When food is cooked, lift the basket out of the oil by the handle. Hang the baskets on the basket support rod to drain.
5. When the heat indicator light cycles off, the fryer is ready to cook the next load.
6. Reduce temperature control to 225ºF during idle periods to save power and extend the life of the oil. The fryer will return to
operating temperature in just a few minutes when needed.
7. Keep the fryer clean at all times. Rinse baskets frequently, and dry thoroughly, in order to prevent oil contamination.
8. Drain the frypot completely after use. Filter the oil daily, or more often during heavy use.
6
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
2. Fill the FRYPOT with commercial-grade liquid shortening to the MIN OIL line.
Capacity: F14
14 pounds
F49, F55
15 pounds
F67, F85
30 pounds (15 pounds per frypot)
CLEANING INSTRUCTIONS
DANGER: BURN HAZARD
Contact with hot oil will cause severe burns. Allow the fryer to cool before cleaning.
Always wear protective clothing and heat resistant gloves when cleaning the fryer.
Turn temperature control to OFF
Allow fryer to cool completely before cleaning
Unplug fryer from receptacle before cleaning
FREQUENCY
Daily, or as needed
TOOLS
Mild Detergent, Non-abrasive cleanser
Soft Cloth or Sponge, Plastic Scouring Pad
Container for disposal of used oil.
PREPARATION
1. Turn temperature control to OFF. Unplug the fryer.
2. Remove fry baskets, then swing the element head up and out of the frypot.
NOTE: The element support rod is spring-loaded. When the element head is raised, the support rod will automatically swing into position to keep the element head raised.
3. Allow the oil to cool to a safe temperature (120ºF or less).
Carefully remove the frypot: wearing heat-resistant gloves, lift the frypot by the handles. Drain the oil into a suitable container.
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
ELECTRIC
SHOCK HAZARD
Disconnect fryer from electric
power before cleaning.
CAUTION:
BURN HAZARD
CLEANING
CAUTION:
4. Frypot and baskets may be washed in a dishwasher, or with warm water and mild detergent. Rinse thoroughly and dry completely.
5. Wipe/brush all crumbs, breading and cooking debris from
elements. Pay particular attention to the area between the element
and the thermobulbs. Be careful that the capillary tubes of the thermobulbs are not moved or damaged during cleaning.
6. Keep all exterior surfaces free from splashed grease by wiping with a clean cloth dampened with warm water and mild detergent. A non-abrasive detergent and plastic scouring pad may be used for stubborn deposits.
IMPORTANT: DO NOT use steel wool or abrasive cleansers as these will damage the surface finish.
IMPORTANT: DO NOT submerge fryer in water. DO NOT spill or pour water into controls, control panel or wiring. Damage to
internal components will occur.
7. Be certain frypot is completely dry, then reinstall in fryer.
a. Be sure the TEMPERATURE CONTROL KNOB is turned to OFF, then plug unit into receptacle.
b. Lower the element head into the frypot by pushing back on the ELEMENT LIFTING HANDLE, raising the SUPPORT ROD, then carefully lowering the elements.
c. Add new or filtered oil to the MIN OIL line in frypot
Procedure is complete.
7
Allow fryer to cool completely
before cleaning.
CAUTION:
ELECTRIC
SHOCK HAZARD
Do not submerge fryer in
water.
IMPORTANT: DO NOT spill
or pour water into controls,
control panel or wiring.
DO NOT submerge fryer in
water. Damage to internal
components will occur.
Damage to internal
components from water
damage is not covered by
warranty.
IMPORTANT: DO NOT
use steel wool or abrasive
cleansers for cleaning the
fryer cabinet or frypot.
To remove carbonization from
frypot and element, see
PERIODIC CLEANING on
page 10.
IMPORTANT:
Nickel plated frypot must be
dried completely in order
to prevent rusting, and to
eliminate water contamination
of the cooking oil.
DISPOSAL OF USED OIL
DANGER: BURN HAZARD
Contact with hot oil will cause severe burns. Allow the fryer to cool before cleaning.
Always wear protective clothing and heat resistant gloves when handling hot oil.
PREPARATION Turn temperature control to OFF
Allow fryer to cool completely before draining
CAUTION:
BURN HAZARD
FREQUENCY Daily, or as needed
TOOLS Container for disposal of used oil.
OIL DISPOSAL
Allow fryer to cool completely
before draining.
CAUTION:
1. Turn temperature control to OFF.
2. Allow the oil to cool to a safe temperature (120ºF or 50ºC).
3. Raise the element head and lift the frypot out of the fryer by the frypot handles.
SLIP AND FALL
HAZARD
Clean up oil spills
immediately. Slipping in oil
can cause injury.
4. Dispose of the used oil in an approved oil disposal receptacle, or filter the oil for reuse.
CAUTION:
5. Wipe the frypot and reinstall in the fryer.
Clean up oil spills
immediately. Oil provides an
environment for the growth
of bacteria, which presents a
health hazard.
Procedure is complete.
8
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
HEALTH
HAZARD
TROUBLESHOOTING SUGGESTIONS
DESCRIPTION
Fryer will not heat
Fryer will not maintain
temperature
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Fryer leaks oil
Element head will not raise, will
not stay in the up position, or will
not lower
SUGGESTED REMEDY
Not plugged in or circuit breaker tripped
Plug into proper receptacle
Reset circuit breaker
Temperature control knob not set to
desired temperature
Set to desired temperature
Hi-limit safety tripped
Clean element1, reset hi-limit
Damaged internal component
Contact Wells Authorized Service
Agency for repairs
Temperature control thermostat
thermobulb contaminated with cooking
debris
Clean element2
Damaged internal component
Contact Wells Authorized Service
Agency for repairs
Damaged frypot
Contact Wells Authorized Service
Agency for repairs
Frypot out of position, or has excess
cooking debris in bottom
Check frypot for position
Clean frypot
Damaged hinge bracket or support rod
Contact Wells Authorized Service
Agency for repairs
The hi-limit safety is designed to shut down the fryer if the oil temperature exceeds 440ºF.
A build-up of cooking debris between the heating element and the thermobulb of the hi-limit
safety will cause the hi-limit to trip prematurely. Clean the element so that oil may circulate
freely between the element and the thermobulb. Reset the safety by pressing the red button
on the bask of the element head.
1
2
POSSIBLE PROBLEM
A build-up of cooking debris between the heating element and the thermobulb temperature
control thermostat will cause inconsistent temperatures. Clean the element so that oil may
circulate freely between the element and the thermobulb.
9
MAINTENANCE
Periodic cleaning is
necessary to remove
carbonization from the
elements and frypot.
PERIODIC CLEANING
Frypot may be cleaned by
the method described at
right, or with a commercial
frypot cleaner. Be sure to
follow the manufacturer’s
directions.
Boil the mixture for five minutes. Turn the control knob to OFF. Allow the
mixture to set in the frypot overnight.
Lower the element into the frypot and set the control knob to 225ºF
After the soak period, raise the elements and remove any remaining
carbonization with a stiff bristle brush. Be careful that the capillary tubes
of the thermobulbs are not moved or damaged during cleaning.
Drain the frypot and wash with warm water and mild detergent.
Reinstall the frypot in the fryer. Add 1 quart of vinegar, then fill to the MAX
OIL line with cold water.
Lower the elements into the vinegar solution. Allow to set for 15 minutes.
Drain the frypot and rinse with clean water. Dry the frypot and elements
thoroughly before returning the fryer to operation.
IMPORTANT: Nickel plated frypot must be dried completely in order to
prevent rusting, and to eliminate water contamination of the cooking oil.
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Before cleaning, ALWAYS:
• Unplug the fryer and
allow to cool.
• Drain the oil and wipe
out the frypot.
Add 1/2 cup of granulated dishwasher detergent to frypot. Fill with water
to the MAX OIL line.
10
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
NOTES
11
EXPLODED VIEW: F14
F14 COUNTERTOP 14# FRYER
30
1
3
2
29
28
4
27
5
2
7
6
8
26
14
5
9
25
23
11
22
12
21
13
20
19
15
18
16
17
Model: F14
COUNTERTOP 14# FRYER
PL301
IL1864 Rev. A 8/17/09
12
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
10
24
PARTS LIST: F14
F14 COUNTERTOP 14# FRYER (LLF-14)
Fig No. Part Number
WS-58656
HI-LIMIT MAN RESET 440°F
2
2C-38667
CLAMP CAPILLARY FLOOR FRY
2E-45061
CORD SET 120V 15A 14G 5-15P
2E-35259
CORD NEMA 6-30P
4
2C-35736
NUT 8-32 HEX KEPS MS GREEN
5
2C-45777
CLAMP BULB LLF-14
6
2B-35637
RING WIRE SS .25ID
7
2K-45788
STRAIN RELIEF SR7W-2-LLF
DD-65783
HANDLE ELEM LIFT ASSY LLF
DD-65784
CLAMP KIT ELEM REAR
3
8
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Description
1
9
2C-35455
NUT 8-32 HEX MS SS
10
2P-32428
SPRING SUPPORT ROD
11
WS-52427
ROD SUPPORT SHORT HEAD
12
E7-35028
COVER CONTROL BOX WO/SAF
13
DD-35890
PROTECTOR SW INF STAND UN
14
2B-45731
FRY BASKET LLF14
15
5E-20169
POT F49 55 67 85 15LB CAP
16
2M-300534
TRADEMARK DOMED LABEL WAR
17
2A-45728
FOOT RUBBER LLW LLF
18
2C-31053
NUT 8-32 KEPS MS NICKEL
19
WS-65765
SHELL ASSY LLF-14
20
2C-35566
SCREW 6-32X1/4 PH TR HD M
21
E7-45767
BRKT HEAD PIVOT LLF-14
22
E7-33436
WASHER SLOTTED PIVOT BRKT
23
2I-35747
GASKET DRWR RWS CLOSED CE
24
E7-45774
BOX CONTROL ASSY LLF-14
25
2B-30792
RING WIRE SS .37ID
2N-45725UL
ELEM 120V FRYER LLF14
2N-45729UL
ELEM 240V FRYER LLF14
27
2T-30133
THERMO CTRL
28
2J-30516
LIGHT SIGNAL AMBER M3938P
29
2R-34066
KNOB CONTROL ASSY F-1905
30
2J-31157
LIGHT SIGNAL RED
2E-307333
RELAY 120VAC 30A
2E-307334
RELAY 240VAC
26
NI
13
EXPLODED VIEW: F49
F49 COUNTERTOP SINGLE-HEAD FRYER
32
1
31
HEAD ASSY COMPLETE, F-49
WS-62899 (208V)
WS-62900 (208/240V)
2
30
29
28
4
3
27
3
6
5
26
7
8
10
25
9
11
24
13
23
22
14
21
20
15
19
18
16
17
Model: F49
COUNTERTOP SINGLE HEAD FRYER
PL301
IL1865 Rev. A 8/17/09
14
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
12
PARTS LIST: F49
F49 COUNTERTOP SINGLE-HEAD FRYER
Fig No.
Description
2R-34066
KNOB CONTROL ASSY
2
2T-30133
THERMO CTRL
3
2C-30157
CLIP CAPILLARY
4
2C-43665
CLAMP THERMO BULB F49
2N-42891UL
ELEM 208V 4600W
2N-42892UL
ELEM 240V 4600W
2B-43688
BASKET WIRE TWIN
5
6
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Part Number
1
2B-43689
BASKET WIRE SINGLE FULL
7
E7-33436
WASHER SLOTTED PIVOT BRKT
8
E7-33435
BRKT PIVOT F49
9
2C-33890
SCREW 12-24X3/4PH PAN ROL
10
2P-32428
SPRING SUPPORT ROD
11
2A-32427
ROD SUPPORT SHORT HEAD
12
2C-31208
WASHER NEOPRENE BASKET
13
2C-31207
WASHER FLAT SS BASKET ROD
14
2D-301344
POT ASSY - F SERIES FRYER
15
2M-300534
TRADEMARK DOMED LABEL
16
2E-35259
CORD SET 250V 30A 12G 6-30P
17
2K-45788
STRAIN RELIEF SR7W-2 LLF
18
2C-35736
NUT 8-32 HEX KEPS MS GREEN
2R-Y5092
FEET ADJ 4GRAY 3/8-16 PK, PLASTIC
19
2A-Z0314
FEET ADJ METAL 4IN
20
DD-34206
SHELL ASSY F49
21
WS-51206
BASKET ROD
22
E7-34323
COVER CONTROL BOX F49
23
2C-35566
SCREW 6-32X1/4 PH TR HD
24
2I-35747
GASKET DRWR RWS CLOSED CE
25
2P-34452
CAP PUSH ON TYPE BASKET
26
2C-49689
CLAMP BULB SS F49RT
27
WS-58656
HI-LIMIT MAN RESET 440°F
28
2J-31157
LIGHT SIGNAL RED
29
2J-30516
LIGHT SIGNAL AMBER
30
2C-30172
NUT 7/8-14 HEX
31
2C-30176
WASHER LOCK FTG TUBE FRAM
32
2I-Z12311
GASKET-FIBER WASHER
NI
WS-62899
HEAD ASSY F49 208V
NI
WS-62900
HEAD ASSY F49 208/240
NI
2E-307334
RELAY 240V
15
EXPLODED VIEW: F55
F55 COUNTERTOP SINGLE-HEAD FRYER
38
1
37
36
HEAD ASSY COMPLETE, F55
WS-62903 (208V)
WS-62904 (240V)
2
35
34
3
33
4
9
3
11
5
32
6
7
26
31
25
10
8
30
24
22
11
29
12
28
13
21
27
14
15
16
20
19
17
18
Model: F55
COUNTERTOP SINGLE HEAD FRYER
PL301
IL1865 Rev. A 8/17/09
16
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
23
PARTS LIST: F55
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
F55 COUNTERTOP SINGLE-HEAD FRYER
Fig No. Part Number
1
2R-35511
2
WS-55510
3
2C-30157
4
2C-49689
2N-42842UL
5
2N-42866UL
6
2C-33890
7
2A-32806
8
2C-31717
9
2B-43688
9
2B-43689
10
2D-301344
11
2E-33068
12
2E-34005
13
2C-35736
14
WS-50131
15
2C-41974
16
2M-300534
17
2C-31053
18
2K-45788
19
DD-74897
2R-Y5092
20
2A-Z0314
21
WS-51206
22
2C-31207
23
2C-31208
24
2I-35747
25
WS-52427
26
2P-32428
27
2C-35566
28
E7-35028
29
WS-50183
30
DD-304644
31
2P-34452
32
2C-49689
33
WS-58656
34
2J-31157
35
2J-30516
36
2C-30172
37
2C-30176
38
2I-Z12311
NI
WS-62903
NI
WS-62904
NI
2E-307334
Description
KNOB CONTROL ASSY SP-715
TEHRMO CTRL FRYER
CLIP CAPILLARY
CLAMP BULB SS
ELEM 208V 5750W
ELEM 240V 5750W
SCREW 12-24X3/4PH PAN ROL
COVER PIVOT BRKT TUMBLED
SCREW 8-32X7/8 PH FL ROLO
BASKET WIRE TWIN
BASKET WIRE F55 SINGLE
POT ASSY - F SERIES FRYER
TERM BLOCK FLAME SENSOR
JUMPER FLAME SENSOR TERM
NUT 8-32 HEX KEPS MS GREEN
TERM BLK KIT-3 POLE .85AMP
NUT 8-32 HEX 7/8 LONG ALU
TRADEMARK DOMED LABEL
NUT 8-32 KEPS MS NICKEL
STRAIN RELIEF`
CORD ASSY 6-50 3W 250V
FEET ADJ 4” GRAY 3/8-16, PLASTIC
FEET ADJ METAL 4”
BASKET ROD
WASHER FLAT SS BAXKET ROD
WASHER NEOPRENE BASKET ROD
GASKET DRWR RWS CLOSED CE
ROD SUPPORT SHORT HEAD
SPRING SUPPORT ROD
SCREW 6-32X1/4 PH TR HD
COVER CONTROL BOX WO/SAF
HINGE BRACKET END
SWITCH LIQUID LEVEL HDWN
CAP PUSH ON TYPE BASKET
CLAMP BULB SS
HI-LIMIT MAN RESET 440F
LIGHT SIGNAL RED
LIGHT SIGNAL AMBER
NUT 7/8-14 HEX
WASHER LOCK FTG TUBE FRAM
GASKET -FIBER WASHER
HEAD ASSY F55 208V
HEAD ASSY F55 240V
RELAY 240VAC
17
EXPLODED VIEW: F67
F67 COUNTERTOP DUAL-HEAD FRYER - FRY HEAD COMPONENTS
1
NOTE: Unit has two identical
fryer heads. Only one is shown
HEAD ASSY COMPLETE, F67
WS-62915 (208V)
WS-62916 (208-240V)
22
2
21
3
20
19
18
5
4
17
4
16
15
7
8
9
10
11
14
13
12
Model: F67
COUNTERTOP DUAL-HEAD FRYER - FRY HEAD COMPONENTS
PL301
IL1867 Rev. A 8/17/09
18
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
6
EXPLODED VIEW: F67
F67 COUNTERTOP DUAL-HEAD FRYER - CABINET COMPONENTS
24
23
25
26
39
27
28
29
30
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
31
32
33
34
38
35
36
37
40
Model: F67
COUNTERTOP DUAL-HEAD FRYER - CABINET COMPONENTS
PL301
IL1868 Rev. B 5/27/10
19
PARTS LIST: F67
Refer to exploded views on pages 18 & 19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
NI
Part Number
WS-62915
WS-62916
2R-34066
2T-30133
2C-30157
2C-43665
2N-42891UL
2N-42892UL
2P-32428
WS-52427
2C-31208
2C-31207
WS-51206
2C-35566
E7-34323
2I-35747
2P-34452
2C-49689
WS-58656
2J-31157
2J-30516
2C-30172
2C-30176
2I-Z12311
2B-43689
2B-43688
2C-33890
2C-31717
2A-32806
H6-33245
WS-53895
2E-33068
2E-34005
WS-50131
2C-41974
2C-35736
2C-31053
2M-300534
2R-Y5092
2A-Z0314
WS-50183
2D-301344
E7-507335
2E-307334
Description
HEAD ASSY F67 208V
HEAD ASSY F67 208-240V
KNOB CONTROL ASSY
THERMO CTRL
CLIP CAPILLARY
CLAMP THERMO BULB
ELEM 208V 4600W
ELEM 240V 4600W
SPRING SUPPORT ROD
ROD SUPPORT SHORT HEAD
WASHER NEOPRENE BASKET
WASHER FLAT SS BASKET
BASKET ROD
SCREW 6-32X1/4 PH TR HD
COVER CONTROL BOX
GASKET DRWR RWS CLOSED CE
CAP PUSH ON TYPE BASKET
CLAMP BULB SS
THERMO HI-LIMIT MAN RESET
LIGHT SIGNAL RED
LIGHT SIGNAL AMBER
NUT 7/8-14 HEX
WASHER LOCK FTG TUBE FRAM
GASKET -FIBER WASHER
BASKET WIRE SINGLE
BASKET WIRE TWIN
SCREW 12-24X3/4PH PAN ROL
SCREW 8-32X7/8 PH FL ROLO
COVER PIVOT BRKT TUMBLED
COVER PIVOT DBL TUMBLE DE
CENTER PIBOT BRKT
TERM BLOCK FLAME SENSOR
JUMPER FLAME SENSOR
TERM BLOCK KIT
NUT 8-32 HEX 7/8 LONG ALU
NUT 8-32 HEX KEPS MS GREEN
NUT 8-32 KEPS MS NICKEL
TRADEMARK DOMED LABEL
FEET ADJ 4 GRAY 3/8-16, PLASTIC
FEET ADJ METAL 4”
HINGE BRACKET END
POT ASSY - F SERIES FRYER
COVER CONTROL BOX
RELAY 240V
20
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Fig No.
F67 COUNTERTOP DUAL-HEAD FRYER
EXPLODED VIEW: F85
F85 - COUNTERTOP DUAL-HEAD FRYER - FRY HEAD COMPONENTS
1
NOTE: Unit has two identical
fryer heads. Only one is shown
HEAD ASSY COMPLETE, F-85
62903 (208V)
62904 (240V)
2
21
20
18
3
19
17
5
4
16
4
6
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
5
7
15
8
9
10
11
14
13
12
Model: F85
COUNTERTOP DUAL-HEAD FRYER, FRY HEAD COMPONENTS
PL301
IL1869 Rev. A 8/18/09
21
EXPLODED VIEW: F85
F85 - COUNTERTOP DUAL-HEAD FRYER - CABINET COMPONENTS
23
22
24
34
38
39
35
36
37
33
40
32
41
31
29
25
28
27
26
Model: F85
COUNTERTOP DUAL-HEAD FRYER,
CABINET COMPONENTS
PL301
IL1870 Rev. A 8/18/09
22
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
30
PARTS LIST: F85
Refer to exploded views on pages 21 & 22.
F85 COUNTERTOP DUAL-HEAD FRYER
Fig No.
Description
Fig No.
Part Number
Description
WS-62903
HEAD ASSY 208V
30
WS-62904
HEAD ASSY 240V
31
2C-35736
NUT 8-32 HEX KEPS MS GREEN
2
2R-35511
KNOB CONTROL ASSY
32
2C-41974
NUT 8-32 HEX 7/8 LONG ALU
3
WS-55510
THERMO CTRL FRYER
33
WS-50131
TERM BLOCK KIT -3POLE
4
2C-30157
CLIP CAPILLARY
34
2C-33890
SCREW 12-24X3/4 PH PAN ROL
5
2C-49689
CLAMP BULB SS
1
2E-33068
TERM BLOCK FLAME SENSOR
35
2C-31717
SCREW 8-32X7/8 PH FL ROLO
2N-42891UL ELEM 208V 4600W
36
2A-32806
COVER PIVOT BRKT TUMBLED
2N-42892UL ELEM 240V 4600W
37
WS-53895
CENTER POST BRKT
2N-42866UL ELEM 400V 5750W
38
H6-33245
COVER PIVOT DBL TUMBLE
2N-42317UL ELEM 480V 575KW
39
2A-30183
BRKT PIVOT CAST
7
2P-32428
SPRING SUPPORT ROD
40
WS-50183
HING BRACKET END
8
WS-52427
ROD SUPPORT SHORT HEAD
41
2C-31053
NUT 8-32 KEPS MS NICKEL
9
2C-31208
WASHER NEOPRENE BASKET
NI
2E-40873
TRANSORMER 480V TO 240V
10
2C-31207
WASHER FLAT SS BASKET ROD
NI
2E-38782
FUSE(KTK)2AMP, 480V ONLY
11
WS-51206
BASKET ROD
12
2C-35566
SCREW 6-32X1/4 PH TR HD
13
E7-34323
COVER CONTROL BOX
14
2I-35747
GASKET DRWR RWS CLOSED CE
15
2P-34452
CAP PUSH ON TYPE BASKET
WS-58656
THERMO HI-LIMIT MAN RESET
2T-38656
THERMO SAF MAN RESET, 480V
2J-31157
LIGHT SIGNAL RED
2J-30516
LIGHT SIGNAL AMBER
M3-WL0113
ASSY, PILOT LIGHT AMBER, 480V
19
2C-30172
NUT 7/8-14 HEX
20
2C-30176
WASHER LOCK FTG TUBE FRAM
21
2I-Z12311
GASKET-FIBER WASHER
22
2B-43689
BASKET WIRE SINGLE
23
2B-43688
BASKET WIRE TWIN
24
2D-301344
POT ASSY - F SERIES FRYER
25
2M-300534
TRADEMARK DOMED LABEL
26
2E-35127
SWITCH ROCK PLAS BEZEL
2R-Y5092
FEET ADJ 4” GRAY 3/8-16
6
16
17
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Part Number
F85 COUNTERTOP DUAL-HEAD FRYER
18
27
28
29
2A-Z0314
FEET ADJ METAL 4”
2E-37779
CONTACTOR 3-POLE 208V 40A
2E-37780
CONTACTOR 3P 240V, 40A ALT3
2E-34005
JUMPER FLAME SENSOR TERM
23
EXPLODED VIEW: F1725
F1725 - COUNTERTOP MULTI-ELEMENT SINGLE-HEAD FRYER HEAD ASSEMBLY COMPONENTS
3
2
1
5
4
6
9
7
25
8
10
24
11
23
22
12
21
14
20
11
19
15
16
10
17
18
Model: F1725
COUNTERTOP MULTI-ELEMENT SINGLE-HEAD FRYER,
CABINET COMPONENTS
PL301
IL1871 Rev. A 8/19/09
24
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
13
EXPLODED VIEW : F1725
F1725 - COUNTERTOP MULTI-ELEMENT SINGLE-HEAD FRYER CABINET COMPONENTS
27
26
28
29
30
32
31
46
45
33
44
43
42
41
40
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
39
34
35
35
38
37
36
Model: F1725
COUNTERTOP MULTI-ELEMENT SINGLE-HEAD FRYER,
CABINET COMPONENTS
PL301
IL1872 Rev. A 3/14/11
25
PARTS LIST: F1725
Refer to exploded views on pages 24 & 25.
F1725 COUNTERTOP DUAL-HEAD FRYER
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
2J-31157
2J-30516
2P-54452
2P-32428
2A-34665
2C-31208
2C-31207
2A-34666
WS-58656
2C-38667
2A-38665
2B-38751
WS-62568
E7-38718
E7-38717
E7-38717
2C-31053
2A-38729
2B-35637
WS-55510
2R-35511
2N-38661UL
2N-38662UL
2C-35566
E7-34662
DD-30147
DD-62850
2E-33068
2E-34005
WS-50131
2C-41974
2C-35736
2B-42705
E7-42347
2M-300534
2E-35127
2E-35128
2C-31053
E7-37896
2R-Y5092
2A-Z0314
2C-31717
2A-32806
2C-33890
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
Description
LIGHT SIGNAL RED
LIGHT SIGNAL AMBER
CAP PUSH ON TYPE BASKET
SPRING SUPPORT ROD
ROD HEAD SUPPORT
WASHER NEOPRENE BASKET
WASHER FLAT SS BASKET
ROD BASKET
THERMO HI-LIMIT MAN RESET
CLAMP CAPILLARY FLOOR FRY
CLAMP BULB FLOOR FRYERS
RING WIRE .250X .093
KIT LIFT HANDLE F1725
BRKT ELEM 5.75KW
CHANNEL ELEM FLOOR FRYER
CHANNEL ELEM FLOOR FRYER
NUT 8-32 KEPS MS NICKEL
HANDLE ASSY LIFT FLOOR
RING WIRE SS .25 ID
THERMO CTRL FRYER
KNOB CONTROL ASSY
ELEM 208V 5750W
ELEM 240V 5750W
SCREW 6-32X1/4 PH TR HD
COVER CONTROL BOX BOTTOM
SWITCH DISCONNECT
PANEL ASSY BK F1725 208V
TERM BLOCK FLAME SENSOR
JUMPER FLAME SENSOR TERM
TERM BLOCK KIT -3POLE
NUT 8-32 HEX 7/8 LONG ALU
NUT 8-32 HEX KEPS MS GREEN
BASKET TWIN WIRE F1725
POT W/O DRAIN F1725 W/STR
TRADEMARK DOMBED LABEL
SWITCH ROCK PLAS BEZEL
SWITCH ROCK PLAS BELEL
NUT 8-32 KEPS MS NICKEL
ACCESS COVER FR RR F2000
FEET ADJ 4” GRAY 3/8-16, PLASTIC
FEET ADJ METAL 4”
SCREW 8-32X7/8 PH FL ROLO
COVER PIVOT BRKT TUMBLED
SCREW 12-24X3/4PH PAN ROL
26
Application
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
Fig No.
PARTS LIST: F1725
F1725 COUNTERTOP DUAL-HEAD FRYER
Fig No.
42
43
44
45
Description
WS-50183
E7-Z12073
2A-35725
2E-Z14960
HINGEBRACKET END
COVER CONTACTOR
GASKET MOLDED CONT BOX
CONTACTOR, 40A 208/240COIL
F1725 CONTACTOR REPLACMENT KIT, NEW
WS-WL0268
CONTACTOR BOX & 1 CONTACTOR
E7-Z12078 BOX - CONTACTOR
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
46
Part Number
27
Application
Mfg after 11/1/2011
Mfg before 11/1/2011
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
WIRING DIAGRAM
28
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
WIRING DIAGRAM
29
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
WIRING DIAGRAM
30
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
WIRING DIAGRAM
31
301 p/n 2M-307588 Owners Manual Counter Top Standard Electric Fryers
WIRING DIAGRAM
32
PARTS & SERVICE
DESCRIPTION
PART NO.
FRY BASKET, HALF-SIZE, ALL EXC. F14 and F1725
FRY BASKET, FULL SIZE FRYPOT, ALL EXCEPT F1725
FRYPOT, F1725
LEGS, ADJUSTABLE METAL
LEGS, ADJUSTABLE PLASTIC
CRUMB CRADLE, FOR F55, F85
FRY BASKET, HALF-SIZE for F1725
COVER, FRYPOT, ALL EXCEPT F14 and F1725
FRY BASKET, HALF-SIZE, FOR F14
CORDSET, FOR F55 50 AMP 1ø NEMA 6-50P
2B-43688
2B-43689
2D-301344
E7-42347
2A-Z0314
2R-Y5092
WS-20690
2B-42705
E7-34421
2B-45731
DD-74897
IMPORTANT: Use only
factory authorized service parts
and replacement filters.
For factory authorized
service, or to order factory
authorized replacement parts,
contact your Wells authorized
service agency, or call:
Wells Bloomfield, LLC
10 Sunnen Dr.
St. Louis MO 63143 USA
Service Dept.
phone: (314) 678-6314
fax:
(314) 781-2714
Service Parts Department
can supply you with the name
and telephone number of
the WELLS authorized
service agency
nearest you.
CUSTOMER SERVICE DATA
please have this information available if calling for service
RESTAURANT _____________________________ LOCATION _____________
INSTALLATION DATE ________________________ TECHNICIAN ___________
SERVICE COMPANY ________________________________________________
ADDRESS ___________________________ STATE ______ ZIP__________
TELEPHONE NUMBER (_____)_____-_________
EQUIPMENT MODEL NO. _______________
EQUIPMENT SERIAL NO. _______________
VOLTAGE:
120
208
33
240
1ø
3ø
WELLS BLOOMFIELD, LLC
10 Sunnen Dr., St. Louis, MO 63143
telephone: 314-678-6314
fax: 314-781-2714
www.wellsbloomfield.com