Gaggenau AC250190 Instruction manual

Add to my manuals
12 Pages

advertisement

Gaggenau AC250190 Instruction manual | Manualzz
[en]
Instruction manual
AC250190
Extractor hood
en
Ú Table of contents
[en]Instruction manual
I mportant safety information
2
E nvironmental protection
Saving energy
Environmentally-friendly disposal
5
5
5
O perating modes
Exhaust air mode
Air recirculation
5
5
5
O perating the appliance
Controls
Setting the fan
Intensive setting
Intermittent mode
Run-on function
Lighting
Saturation signal
6
6
6
6
7
7
7
7
C leaning and maintenance
Cleaning agents
Cleaning the metal mesh grease filters
Removing metal grease filter
Installing the metal mesh grease filter
Replacing the batteries in the remote control
8
8
8
9
9
9
(
7
Ç
1
2
Trouble shooting
10
After-sales service
10
A ccessories for air recirculation mode
11
3
_
Additional information on products, accessories,
replacement parts and services can be found at
www.gaggenau.com and in the online shop
www.gaggenau.com/zz/store
m Important safety
information
(
Read these instructions carefully. Only then will
you be able to operate your appliance safely
and correctly. Retain the instruction manual
and installation instructions for future use or for
subsequent owners.
onimrtanfiyetfasntampIor
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old at a
safe distance from the appliance and power
cable.
2
Important safety information
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
m Warning – Danger of suffocation!
en
Safe operation is possible only when the partial
vacuum in the place where the heat-producing
appliance is installed does not exceed 4 Pa
(0.04 mbar). This can be achieved when the air
needed for combustion is able to enter through
openings that cannot be sealed, for example in
doors, windows, incoming/exhaust air wall
boxes or by other technical means.
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
m Warning – Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room if
the appliance is being operated in exhaust air
mode at the same time as room air-dependent
heat-producing appliance is being operated.
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
m Warning – Risk of fire!
Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
Risk
of fire! deposits in the grease filter may
▯ Grease
▯
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coal-operated
heaters, continuous flow heaters or water
heaters) obtain combustion air from the room
in which they are installed and discharge the
exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
▯
Adequate incoming air must therefore
always be ensured.
▯
An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must be
no flying sparks.
Risk
of fire!
▯ Hot
oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch
off the hotplate. Extinguish flames carefully
using a lid, fire blanket or something
similar.
3
en
Important safety information
Risk
of fire!gas burners are in operation without
▯ When
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk
of fire! several gas burners at the same
▯ Operating
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner
of more than 5 kW (wok) is equivalent to
the power of two gas burners.
m Warning – Risk of burns!
The accessible parts become very hot when in
operation. Never touch hot parts. Keep
children at a safe distance.
m Warning – Risk of injury!
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
▯ Items
placed on the appliance may fall
▯
down. Do not place any objects on the
appliance.
Risk
of injury!
▯ The
light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
m Warning – Risk of electric shock!
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock!
▯ Incorrect
repairs
are dangerous. Repairs
▯
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk
of not
electric
shock!
▯ Do
use any
high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless steel
cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and abrasive
cleaning agents.
Risk of damage from returning condensate.
Install the exhaust duct in such a way that it
falls away from the appliance slightly
(1° slope).
4
Environmental protection
E nvironmental protection
7
Your new appliance is particularly energy-efficient. Here
you can find tips on how to save even more energy when
using the appliance, and how to dispose of your
appliance properly.
onitecopronmlaretEinv
en
O perating modes
Ç
E xhaust air mode
mngodesiOtaper
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
Saving energy
▯
Only switch the ventilation on when necessary. You
do not need to switch the ventilation on when
cooking something for a short time that does not
have a strong smell.
Note: The air must not be discharged into a flue that is
used for exhausting fumes from appliances burning gas
or other fuels (not applicable to appliances that only
discharge the air back into the room).
▯
Select a fan setting according to what you are
cooking.
▯
▯
Switch the ventilation off again after cooking.
Before conveying the exhaust air into a nonfunctioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
▯
Cleaning the grease filter regularly will increase the
efficiency of the ventilation.
▯
If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance
with European Directive 2012/19/EU
concerning used electrical and electronic
appliances (waste electrical and electronic
equipment - WEEE). The guideline
determines the framework for the return and
recycling of used appliances as applicable
throughout the EU.
Air recirculation
The air which is drawn in is cleaned by
the grease filters and an activated
carbon filter, and is conveyed back into
the kitchen.
Note: To bind odours in air recirculation mode, you
must install an activated carbon filter. The different
options for operating the appliance in air recirculation
mode can be found in the brochure. Alternatively, ask
your dealer. The required accessories are available from
specialist retailers, from customer service or from the
Online Shop.
5
Operating the appliance
en
O perating the appliance
1
Note: If no audible signal sounds within 30 seconds,
repeat this procedure.
Extractor hood's control panel
Notes
encaipalhetngiOtaper
–
Press the buttons briefly to activate the various
functions. The function you are trying to select will
not be activated if you hold the button down for too
long.
–
The appliance will emit a beep to confirm that a
button has been pressed.
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
(
0
Fan settings display
Operating buttons
Operating buttons
Controls
Use the remote control to set and adjust the various
different functions of your appliance.
Note: The remote control requires 23AE 12 V batteries.
For information on how to insert the batteries, refer to
the section entitled~ "Cleaning and maintenance"
on page 8
Note: Heat and penetrating moisture may damage the
remote control. Never expose the remote control to
intense heat or moisture.
Remote control
Explanation
@
#
A
@
ž
Light on/off/dimming
Switch the extractor hood on and off
Decrease fan setting
Increase fan setting
Fan run-on
Setting the fan
Note: Always adjust the setting according to the current
conditions. To eliminate strong cooking smells, select a
high fan setting.
Switching on
Operating buttons
Explanation
=
g
ž
@
A
Light on/off/dimming
1
Press the @ button.
The fan will start at fan setting ƒ .
2
Press the @ or A button to set a different fan
setting.
Note: The appliance has three fan settings and an
intensive setting. To set the lowest setting,
press A once. If you press it more than once, the
appliance will switch off again.
Switching off
Fan run-on
Press and hold the A button until the appliance
switches off.
Increase fan setting
or press the ÿ button.
Intermittent ventilation
Decrease fan setting
Connecting the remote control to the appliance
Intensive setting
If the appliance cannot be operated with the remote
control, e.g. after the battery has been changed, the
connection between the remote control and the
appliance must be re-established.
You can use the intensive setting if there is a large buildup of odours and fumes/vapours.
1
Press and hold the @ button.
2
Attach the appliance to the mains voltage.
A long audible signal sounds. The remote control
has been connected to the appliance.
6
Press and hold the @ button until ˜ appears in the fan
settings display .
Note: Intensive mode runs for four minutes. Once this
time has elapsed, the appliance will switch back to fan
setting ƒ .
Operating the appliance
Intermittent mode
Lighting
Intermittent mode automatically switches on the
extractor hood for 10 minutes every hour. The function
switches itself off again after 24 hours.
Press the @ button on the control panel or the
= button on the remote control.
This function can be activated from the control panel or
using the remote control.
en
Saturation signal
Note: If intensive mode or the run-on function has been
activated, the intermittent function will not be available.
The following will happen when the filters are saturated:
▯
The ª symbol appears in the display: Clean the
metal grease filter
Switching on intermittent mode from the control
panel
▯
The ’ symbol appears in the display and a signal
sounds: Replace the activated charcoal filter
1
Press the ÿ and @ buttons at the same time. ‚ will
appear on the display.
2
Press the @ or A button to set a different fan
setting.
3
Press the ÿ and @ buttons at the same time to
confirm the fan setting for intermittent mode.
Switching on intermittent mode using the remote
control
See the "CleanAir air recirculation module" printed
supplement or the section entitled~ "Cleaning and
maintenance" on page 8
Resetting the saturation signal
When the fan is switched off, the signal is also switched
off.
1
Press the g button. ‚ will appear on the display.
The relevant filter(s) should be cleaned now if you have
not already done so.
2
Press the @ or A button to set a different fan
setting.
Switching over the appliance to air recirculation
3
Press the g button to confirm the fan setting for
intermittent mode
1
Switch off the appliance.
2
Press the ÿ and ž buttons on the control panel at
the same time until the ’ indicator lights up. Then
release the buttons.
Note: Pressing any of the buttons (except the button for
the light) will deactivate intermittent mode.
Run-on function
The run-on function allows the extractor hood to
continue running for a few minutes after it has been
switched off. This eliminates any remaining cooking
smells. The extractor hood will then switch itself off
automatically.
Switching on
Note: If intensive mode has been activated, the run-on
function will not be available.
Press the ž button on the control panel or on the
remote control.
The ’ indicator will go out shortly afterwards. The
electronic controller has now been switched over to air
recirculation mode.
Switching over the appliance to air extraction
Note: The default setting is air extraction mode.
1
Switch off the appliance.
2
Press the ÿ and ž buttons on the control panel at
the same time until the ª indicator lights up. Then
release the buttons.
The ª indicator will go out shortly afterwards. The
electronic controller has now been switched over to air
extraction mode.
The fan will run for 10 minutes at setting ‚ and a dot will
flash on the display during this time. Then the fan will
switch itself off automatically.
Switching off
Press the ž button on the control panel or the extractor
hood's remote control.
This will deactivate the run-on function immediately.
7
Cleaning and maintenance
en
C leaning and maintenance
Area
Cleaning agent
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
2
m
encatmdiangeCl
Warning – Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
m
Controls
Warning – Risk of electric shock!
Risk of electric shock caused by penetrating moisture.
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
m
Do not use any stainless steel cleaners.
Warning – Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
m
Risk of damage to the electronics from
penetrating moisture. Never clean operating controls with a wet cloth.
Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning the metal mesh grease
filters
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
Cleaning agents
m
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
Grease deposits in the grease filter may catch fire.
▯
Harsh or abrasive cleaning agents,
▯
Cleaning agents with a high alcohol content,
▯
Hard scouring pads or cleaning sponges,
▯
High-pressure cleaners or steam cleaners.
Warning – Risk of fire!
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
–
Do not use any aggressive, acidic or alkaline
cleaning agents.
–
When cleaning the metal mesh grease filters, also
clean the holder for the metal mesh grease filters in
the appliance using a damp cloth.
Follow all instructions and warnings included with the
cleaning agents.
–
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
Area
Cleaning agent
By hand:
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
Note: You can use a special grease solvent for stubborn
dirt. It can be ordered via the Online Shop.
Wash new sponge cloths thoroughly before use.
Clean stainless steel surfaces in the
grind direction only.
Painted surfaces
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
8
▯
Soak the metal mesh grease filters in a hot soapy
solution.
▯
Clean the filters with a brush and then rinse them
thoroughly.
▯
Leave the metal mesh grease filters to drain.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no
effect on the function of the metal mesh grease filters.
▯
Do not clean heavily soiled metal mesh grease
filters together with utensils.
▯
Place the metal mesh grease filters loosely in the
dishwasher. The metal mesh grease filters must not
be wedged in.
Cleaning and maintenance
Removing metal grease filter
1
Open the filter cover by pulling it downwards.
Notes
en
Replacing the batteries in the remote
control
– The filter cover is heavy. Hold the filter cover
with both hands.
– Open the filter cover slowly and carefully.
2
Press the lock on the metal grease filters.
Note: To avoid causing damage, do not bend the
metal grease filter.
1
Undo screws.
2
Remove cover.
3
Remove the batteries.
4
Correctly insert the new batteries (23AE 12 V).
5
Dispose of flat or faulty batteries according to local
regulations.
Note: Do not dispose of batteries in general household
waste.
3
Take the metal grease filter out of the holder.
Note: Fat may accumulate in the bottom of the
metal grease filter. Hold the metal grease filter level
to prevent fat from dripping out.
4
Clean the appliance from the inside.
5
Clean the metal grease filter and let it dry before
refitting it.
Installing the metal mesh grease filter
1
Insert metal grease filter.
While doing this, place your other hand under the
metal grease filter.
2
Fold up metal grease filter and engage the lock.
3
Close the filter cover upwards.
Note: Ensure that the filter cover lock engages
correctly.
9
en
Trouble shooting
Trouble shooting
After-sales service
3
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
ngihosteublTr
m
Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by one
of our trained after-sales technicians. If the appliance is
defective, unplug the appliance from the mains or switch
off the circuit breaker in the fuse box. Contact the aftersales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a
licensed technician (electrician).
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find the right
solution in order to avoid unnecessary visits from a
service technician.
When calling us, please give the product number (E no.)
and the production number (FD no.) so that we can
provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal mesh grease filter to gain access).
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
E no.
FD no.
After-sales service O
Malfunction table
Fault
The appliance
does not work
Possible cause
The plug is not
plugged into
the mains
Power cut
The fuse is
faulty
Solution
Connect the appliance to
the power supply
Check whether other
kitchen appliances are
working
Check in the fuse box to
make sure that the fuse for
the appliance is in working order
Call the after-sales service
The lighting is
not working
The ’ symbol
appears in the
display and a
signal sounds.
The remote
control is not
working
The LED lights
are defective
The activated
Replace the filter; see the
charcoal filter is "CleanAir air recirculation
saturated.
module" printed supplement
The appliance
is not responding to the
remote control
The remote
control is not
connected to
the appliance
--------
10
The battery is
flat
Replace the batteries in
the remote
control.~ "Cleaning
and maintenance"
on page 8
Connect the remote control to the
appliance.~ "Cleaning
and maintenance"
on page 8
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8988
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak.
Off peak 0.0088 € per minute.
AU
1300 368 339
NZ
09 477 0492
Trust the expertise of the manufacturer, and rest
assured that the repair will be carried out by trained
service technicians using original spare parts for your
domestic appliance.
Accessories for air recirculation mode
en
A ccessories for air recirculation mode
_
(not supplied)
mondeitaulcrieriaorfesiAoresc
AA010810
AA200110
11
9001161261 (970412)
en
*9001161261*
*DJJHQDX+DXVJHUlWH*PE+
&DUO:HU\6WUD‰H
0QFKHQ
*(50$1<
ZZZJDJJHQDXFRP

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement