important safety instructions danger warning save these

important safety instructions danger warning save these
ENGLISH
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electric product, basic
MG7750
precautions should always be followed,
including the following:
Read all instructions before using this
product.
DANGER
BC
To reduce the risk of electric shock:
-- Do not reach for a corded product
that has fallen into water. Unplug
immediately.
-- Use product only in dry condition.
Do not use while bathing or in a shower.
-- Do not submerge product in water.
-- Do not place or store the product where
it can fall or be pulled into a tub or sink.
Do not place or drop the product in
water or other liquid.
-- Always unplug this product from the
electrical outlet immediately after use,
except when product is (re)charging.
-- Unplug and remove power supply cord
from this product before cleaning.
-- The batteries used in this product may
present a fire or chemical burn hazard
if mistreated. Do not disassemble, heat
above 100°C (212°F) or incinerate.
WARNING
Manufactured for:
Philips Consumer Lifestyle
A division of Philips Electronics
North America Corporation
P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means
it is listed by Underwriters’ Laboratories, Inc.
Norelco is a registered trademark of
Philips Electronics North America Corporation.
PHILIPS and Philips shield are registered trademarks of
Koninklijke Philips N.V.
©2017 Philips Electronics North America
Corporation. All rights reserved.
www.philips.com
4222.002.8788.3
To reduce the risk of burns, fire, electric
shock, or injury to persons:
-- Close supervision is required when this
product is used by, on, or near children,
or persons with limited physical, sensory,
or mental capabilities or invalids.
-- Use this product only for its intended
use as described in this manual. Do not
use attachments not specified by Philips
Electronics North America Corporation.
-- Never operate this product if it has a
damaged power cord, if it is not working
properly, if it has been dropped or
damaged, or dropped into water while
plugged in. For assistance call 1-800243-3050.
-- Product can be rinsed under running
tap water. Never use water hotter than
175°F (80°C). Do not charge or operate
the product until fully dried.
-- Keep the product, power cord and
any attachments away from heated
surfaces.
-- Never drop or insert any object into any
opening.
-- Do not use the adapter in or near a
power outlet that contains an electric
air freshener to prevent damage to the
power cord.
-- Do not operate, charge, clean or plug
in product outdoors or operate where
aerosol (spray) products are being used
or where oxygen is being administered.
-- Always check cutters, cutting unit and
guards before using the product. Do not
use the product if cutters, cutting unit or
guards are damaged, as injury may occur.
-- Always attach power cord to product
first, then to power outlet. Be certain
plug is inserted firmly into product up to
mark indicated on plug. To disconnect
turn product off then remove power cord
from outlet.
-- Keep the power cord dry at all times.
Do not handle with wet hands.
-- Never put the product in direct sunlight
or store at a temperature above 140°F
(60°C).
-- To prevent possible damage to the
power cord, do not wrap power cord
around the product.
-- This product is for use on human hair
only. Do not use the product for any
other purpose.
-- Always store the product, attachments
and power cord in a moisture-free area.
Make sure the cord is disconnected
from the product.
-- Do not attempt to open the product
to remove/replace the built-in
rechargeable battery.
-- Only use the power cord and other
accessories supplied with the product.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a
transformer. Do not cut off the power plug
to replace it with another plug as this will
cause a hazardous condition.
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benefit from the support that
Philips Norelco offers, register your
product at www.norelco.com/register.
21 Fading hair guard 5/32in.-3/8in. (4-9mm)
22Fading hair guard 5/32in.-3/8in. (4-9mm)
23Body guard 1/8in. (3mm)
24Body guard 3/16in. (5mm)
Not shown: cleaning brush, pouch
This symbol indicates that the
product can be rinsed under
running
tap water.
21
22
23
24
25
3
4
26
1
9
2
3/64in
1mm
18
11
5
3/8in
9mm
1/8in
3mm
6
7
2
19
12
3/16in
5mm
4
15/32in
12mm
2
20
13
9/32in
7mm
21
8
14
1
1
21/32in
16mm
5
6
5/32in – 3/8in
4-9mm
9
22
10
1
2
15
16
23
11
7
8
28
5/32in
4mm
5/64in
2mm
3
27
17
10
1/8in
3mm
3/16in
5mm
12
13
24
General description (Fig. 1)
1 Extra-wide hair trimmer
2Precision trimmer
3Nose trimmer
4Precision shaver
5Full-size hair trimmer
6On/off button
7Battery status indicator
8Socket for small plug
9Stubble guard 3/64in. (1mm)
10Stubble guard 5/64in. (2mm)
11Beard guard 1/8in. (3mm)
12Beard guard 3/16in. (5mm)
13Beard guard 9/32in. (7mm)
14Eyebrow guard 1/4in. (6mm)
15Power plug
16Small plug
17Hair guard 5/32in. (4mm)
18Hair guard 3/8in. (9mm)
19Hair guard 15/32in. (12mm)
20Hair guard 21/32in. (16mm)
14
17
15
18
16
19
3After charging, remove the power plug
from the wall outlet and pull the small
plug out of the product.
Note: An adapter plug may be necessary
for cord usage in some foreign countries.
Use an attachment plug adapter of the
proper configuration for power outlet.
Quick charge
After approx 5 minutes charging,
the product contains enough power
for one cordless trimming session.
Charging
2
1
20
Battery status indications
-- When the battery is almost empty,
the battery status indicator lights up
orange (Fig. 2).
-- When the product is charging, the
battery status indicator flashes white
slowly (Fig. 3).
-- During quick charge, the battery status
indicator flashes white quickly. After
approx. 5 minutes of charging, the
battery indicator flashes white slowly.
The product now contains enough
power for one cordless trimming session.
-- When the battery is fully charged, the
battery status indicator lights up white
continuously (Fig. 4).
Note: After approx. 30 minutes, the light
goes out automatically.
Charging
Charge the product before first use and
when the display indicates that the battery
is almost empty. When the product has
charged for 3 hours, it has a cordless
operating time of up to 5 hours.
-- Charging, recharging or using the product
at temperatures below 40°F (4,5°C) or
higher than 95°F (35°C) adversely affects
the lifespan of the battery.
-- If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize
for 30 minutes before use.
1Make sure the product is turned off.
2Insert the small plug into the product
and put the power plug in any 120V AC
outlet (Fig. 5).
Using the product
Always check the product and all accessories
before using. Do not use the product or any
accessory if it is damaged, as this may cause
injury. Always replace a damaged part with
one of the original type.
Note: This product can be used without
cord or directly from the power outlet.
Note: Switch off and clean the product
and attachments after each use.
-- Use this product for its intended
household use as described in this
manual.
-- For hygienic reasons, the product
should only be used by one person.
-- Trimming is easier when the skin and
hair are dry.
-- Be careful when trimming without a
guard as when the product is turn on it
will trim every hair it touches.
Detaching and attaching cutting elements
1 To detach a cutting element, push
upwards against the teeth of the cutting
element and take it off the handle (Fig. 6).
2To attach a cutting element, insert
the lug of the cutting element into the
guiding slot at the front and push the
back of the cutting element onto the
product (`click`) (Fig. 7).
Detaching the precision shaver and
nose trimmer
1Place your finger on the arrow at the
back of the attachment and push it off
the handle in the direction of the arrow
(Fig. 8).
Attaching and detaching guards
1To attach any type of guard onto a
cutting element, slide the front part of
the guard onto the teeth and push the
projection at the back of the guard into
the product (`click`) (Fig. 9).
2To detach any type of guard from the
cutting element, carefully pull its back
part off the product and then slide it off
the cutting element (Fig. 10).
Note: When trimming for the first time,
start by using the guard with the maximum
trimming length setting to familiarize
yourself with the product.
Switching the product on and off
1Press the on/off button once to turn the
product on or off (Fig. 11).
Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a
guard to trim hair close to the skin (to
a length of 1/32in (0.5mm) or to create
clean lines around your beard, neck and
sideburns.
1To trim hair close to the skin, place the
flat side of the cutting element against
your skin and make strokes against the
direction of hair growth (Fig. 12).
2For contouring, hold the cutting
element perpendicular to the skin and
move it upwards or downwards with
gentle pressure (Fig. 13).
Beard guards
Attach a beard guard to the full-size hair
trimmer to trim your beard and moustache
evenly. The product comes with 5 beard
guards. The hair length settings are
indicated on the guards. The settings
correspond to the remaining hair length
after trimming.
Guard
inch
mm
Stubble guard
3/64in.
1mm
Stubble guard
5/64in.
2mm
Beard guard
1/8in.
3mm
Beard guard
3/16in.
5mm
Beard guard
9/32in.
7mm
1Attach the guard to the full-size hair
trimmer.
2To trim the most effective way, move
the guard against the direction of hair
growth (Fig. 14). Make sure the surface
of the guard always stays in contact
with the skin.
Attachments for use on body
-- Use the green body guards to trim
body hair.
-- When you trim for the first time, use the
5mm/3/16in. body guard to familiarize
yourself with the product.
-- Make sure hair is clean and dry as wet
hair tends to stick to the body and,
when trimming sensitive areas, always
use a body guard.
-- Since all hairs do not grow in the same
direction, you may want to try different
trimming positions (i.e. upwards,
downwards, or across). Practice is best
for optimum results.
-- Always make smooth and gentle
movements and be sure the surface of
the guard always stays in contact with
your skin.
-- When too many hairs have accumulated
on the product, blow the hairs out
before use, for best trimming results.
Body guards
Attach a body guard to the full-size hair
trimmer to trim hairs below the neckline.
The product comes with 2 body guards.
The hair length settings are indicated on
the guards. The settings correspond to
the remaining hair length after trimming.
Guard
inch
mm
Body guard
(green)
1/8in.
3mm
Body guard
(green)
3/16in.
5mm
1Attach a body guard to the full-size hair
trimmer (see `Attaching and detaching
guards`).
2To trim in the most effective way,
stretch the skin with your free hand and
move the guard against the direction
of hair growth (Fig. 15). Make sure the
surface of the guard always stays in
contact with the skin.
Attachments for use on head
Extra-wide hair trimmer
Use the extra-wide hair trimmer without
a guard to clip the hair on your head very
close to the skin (1/32in (0.5mm) or to
contour the neckline and area around
the ears.
1To contour the hairline around the ears,
comb the hair ends over the ears.
2Tilt the product in such a way that only
one edge of the cutter blades touches
the hair ends when you shape the
contours around the ears.
3To contour the nape of the neck or
sideburns, turn the product and make
downward strokes (Fig. 16).
4Move the product slowly and smoothly
following the natural hairline.
Hair guards
Attach a hair guard to the extra-wide
hair trimmer to evenly trim the hairs on
your head. The product comes with
4 hair guards. The hair length settings
are indicated on the guards. The settings
correspond to the remaining hair length
after trimming.
Guard
inch
mm
Hair guard
5/32in.
4mm
Hair guard
3/8in.
9mm
Hair guard
15/32in.
12mm
Hair guard
21/32in.
16mm
1Attach a guard to the extra-wide hair
trimmer.
2Move the trimmer slowly over the
crown from different directions to
achieve an even result. Make sure the
surface of the guard always stays in
contact with the skin.
- Always move the trimmer against
the direction of hair growth (Fig. 17).
Press lightly.
- Make overlapping passes over the
head to ensure that all hair that
should be cut has been cut.
Fading hair guard
Attach the fading hair guards to the extrawide hair trimmer to trim the hair around
the ears with a faded result. The product
comes with 2 guards. Use both guards to
trim hair around both ears. Choose a hair
guard based on the preferred trimming
direction of back to front or front to back.
Always make sure that you hold the side
of the guard with the short teeth closest to
your ear.
Guard
inch
mm
Fading hair
guards
5/32in.23/64”
4-9mm
1Attach the guard to the extra-wide hair
trimmer to trim the hair around the ear.
Then attach the other guard to trim the
hair around the other ear.
2Place the product on your hair at the
back or front of your ear, depending
on the trimming direction you prefer.
Always make sure that the side of the
guard with the short teeth is closest to
your ear.
3Move the trimmer slowly around the
ear, while holding it steady (Fig. 18).
For best results, move the trimmer
against the direction of hair growth
(back to front).
Precision attachments for use on face
Precision trimmer
Use the precision trimmer to create fine
lines and contours around your facial
style, close to the skin (to a length of
1/32in (0.5mm)).
1Hold the precision trimming head
perpendicular to the skin and move the
trimming head upwards or downwards
with gentle pressure (Fig. 19).
Eyebrow guard
Use the full-size hair trimmer with
the eyebrow guard attached for tidying
up eyebrows or trimming sideburns to a
length of 1/4in. (6mm).
1Slowly move the trimmer against the
hair growth direction. Press lightly and
make sure that the surface of the comb
always stays in contact with the skin
(Fig. 20).
Nose trimmer
Use the nose trimmer to trim your nose
hair and ear hair.
-- Make sure nasal passages are clean.
Make sure outer ear channels are clean
and free from wax.
-- Do not insert the tip more than 3/16in
(0.5cm).
-- Always clean the attachment after each
use.
Trimming nose hair
1Gently move the tip in and out of nose
while turning it around to remove
unwanted hairs (Fig. 21).
Trimming ear hair
1Slowly move the tip round the ear to
remove hairs that stick out beyond the
rim of the ear.
2Gently move the tip in and out of the
outer ear channel to remove unwanted
hairs (Fig. 21).
Precision shaver
Use the precision shaver after trimming, to
shave unwanted hairs on cheeks, chin and
along the beard with precision. Make sure
to pre-trim your beard first, with the fullsize hair trimmer without guard, to obtain
the best result.
Note: Use the precision shaver to remove
remaining hairs and detailing your beard
style. It is not suitable for a full face shave.
1Gently press the precision shaver onto
the skin and shave along contoured
edges to remove any unwanted hairs
(Fig. 22).
Cleaning
Never use scouring pads, abrasive
cleaning agents or aggressive liquids
such as gasoline or acetone to clean
the product.
Never dry the trimmer teeth with a
towel or tissue, as this may damage the
trimmer teeth.
After every use: cleaning under the tap
1Turn off the product and disconnect
from the power outlet.
2Remove any guard (see `Attaching and
detaching guards`) or cutting element
(see `Detaching and attaching cutting
elements`) from the product.
3Rinse the hair chamber under a warm
tap.
4Clean the cutting element and guard
under a warm tap (Fig. 23).
5Carefully shake off excess water and let
all parts air dry completely.
Thorough cleaning
1Turn off the product and disconnect
from the power outlet.
2Wipe the handle of the product with
a dry cloth.
3Remove any guard (see `Attaching and
detaching guards`) or cutting element
(see `Detaching and attaching cutting
elements`) from the product.
4Remove any hairs that have
accumulated in the hair chamber with
the cleaning brush supplied.
Remove any hairs that have accumulated
5
in the cutting elements and/or guards
with the cleaning brush supplied.
6Clean the cutting elements under a
warm tap (Fig. 23).
7Clean the guards under a warm tap.
8Carefully shake off excess water and let
all parts air dry completely.
Cleaning the nose trimmer
Clean the nose trimmer immediately after
use and when a lot of hair or dirt has
accumulated on the nose trimmer head.
1Rinse the nose trimmer head with hot
water (Fig. 24).
2Turn on the product and rinse the nose
trimmer head once more to remove
any remaining hairs. Then turn off the
product again.
For a thorough clean, immerse the nose
trimmer head in a bowl with warm water
for a few minutes and then turn on the
product to remove stubborn hair/debris.
3Carefully shake off excess water and let
all parts air dry completely.
Cleaning the precision shaver
1Hold the precision shaver at the
grooves on each side and pull the top
part off the bottom part (Fig. 25).
2Blow and/or shake out any hair that
has accumulated inside the precision
shaver (Fig. 26).
3Clean the top part of the precision
shaver under a warm tap (Fig. 27).
4Carefully shake off excess water and let
all parts air dry completely.
5Reattach the top part onto the bottom
part of the precision shaver.
This product has no other userserviceable parts. For assistance call
1-800-243-3050.
Storage
-- Store the product in the pouch
supplied. Make sure the product is dry
before you store it in the pouch.
-- Be sure the product is turned off.
Remove cord from outlet and the
product before storing it in a safe, dry
location where it will not be crushed,
banged, or subject to damage.
-- Do not wrap cord around the product
when storing.
-- Store cord in a safe location where it
will not be cut or damaged.
-- Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Accessories
Replacement parts and accessories may
be purchased at a store near you or on our
website www.philips.com/store.
Assistance
For assistance, visit our website:
www.philips.com/support or call toll free
1-800-243-3050.
Online information is available 24 hours
a day, 7 days a week.
Disposal
-- This product contains a rechargeable
lithium-ion battery which must be
disposed of properly (Fig. 28).
Contact your local town or city officials
for battery disposal information.
You can also call 1-800-822-8837 or
visit www.call2recycle.org for battery
drop-off locations.
-- For assistance, visit our website
www.philips.com/support or call
1-800-243-3050 toll free.
-- Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused. For recycling
information, please contact your local
waste management facilities or visit
www.recycle.philips.com
Full Two-Year Warranty
Philips Electronics North America
Corporation warrants this new product
(except foil, cutters and guards) against
defects in materials or workmanship for
a period of two years from the date of
purchase, and agrees to repair or replace
any defective product without charge.
IMPORTANT: This warranty does not
cover damage resulting from accident,
misuse or abuse, lack of reasonable
care, the affixing of any attachment not
provided with the product or loss of parts
or subjecting the product to any but the
specified voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED
FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply
go to www.philips.com/norelco or call
1-800-243-3050 for assistance. It is
suggested that for your protection you
return shipments of product by insured
mail, insurance prepaid. Damage occurring
during shipment is not covered by this
warranty.
NOTE: No other warranty, written or oral,
is authorized by Philips Electronics
North America Corporation.
This warranty gives you specific legal
rights, and you may also have other rights
which vary from state to state. Some
states do not allow the exclusion or
limitation of incidental or consequential
damages, so the above exclusion and
limitations may not apply to you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satisfied with your
product send the product back and we’ll
refund you the full purchase price.
The product must be shipped prepaid
by insured mail, insurance prepaid, have
the original sales receipt, indicating
purchase price and date of purchase,
and the money-back guarantee return
authorization form enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later
than 45 days after the date of purchase.
Philips reserves the right to verify the
purchase price of the product and limit
refunds not to exceed suggested retail price.
To obtain money-back guarantee return
authorization form, call 1-800-243-3050
for assistance.
Delivery of refund check will occur
6–8 weeks after receipt of returned
product.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement