installation guide - Mor Electric Heating Assoc., Inc.

installation guide - Mor Electric Heating Assoc., Inc.
installation guide
ASKS series
Kick space heater
warning
TÈME QUAL
ITÉ
SYS
EG
IÉ - R ISTERE
D
TIF
Q
ER
STEM
Y SY
LIT
UA
This unit
complies with
CSA and UL
standards
C
Replacement component list included
important INSTRUCTIONS
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future reference.
If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and building codes effective in
your region.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
This unit must be grounded.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative). Use this heater only as described in this manual.
Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. Do not use outdoors.
Recommended heating capacity: 1.25 W/cubic foot (0.03 m³)
For further information or to consult this guide online, please visit our website at www.stelpro.com
INSASKS0913
technical drawings
warning
It corresponds to 10 W/square foot (0.09 m²) based on a standard ceiling height of 8 feet (2.44 m). The recommended capacity is usually sufficient for normal
heating needs. Please note that the insulation quality of walls and windows are some of the factors that influence heat loss, which modify the required capacity to
heat a room. If needed, refer to a specialist (industrial and commercial buildings) who will be able to calculate these heat losses and optimize the required capacity
or consult the “Tools/Heating Calculator” section of the Stelpro Design website (residential buildings).
Do not install the unit where objects or pieces of furniture could be damaged by heat.
If the unit capacity is insufficient for the size of the room, it will be in operation continuously, and may become defective earlier and turn yellow.
Respect distances and positions indicated in the installation section.
If the installer or the user modifies the unit, he will be held responsible for any damage resulting from this modification, and the CSA certification could be void.
This unit must not come into contact with a water source and must be protected from splashes (e.g. a wet mop). Do not use it if any part has been immersed.
Moreover, do not turn it on or off when standing in water or if your hands are wet.
When starting up the unit for the first time or after a long period, it is normal that it produce some temporary odours and a whitish smoke.
Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be careful and responsible when using it. To avoid burns, do not touch
hot surfaces with bare skin. Allow the unit to cool down for a few minutes since it stays warm for some time after shut-down. Extreme caution is necessary when any
heater is used by or near children or invalids and whenever the heater is left operating and unattended.
DANGER – High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of this heater.
Never block air vents (with objects or other items). You risk damaging the heater and the obstruction could lead to electric shock or overheating, which could result
in a fire.
Do not insert or allow foreign objects to enter the air vent as this may cause electric shocks, fires, or damages to the unit.
This unit becomes very hot and may generate arcing and sparking. It is not designed to be used or stored in wet areas or areas containing flammable liquids,
combustible materials or corrosive, abrasive, chemical, explosive and flammable substances such as, but not limited to, gasoline, paint, chlorine, sawdust and
cleaning products.
Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the unit must be cleaned based on the amount of dirt accumulated on and inside
air vents. Accumulated dirt can lead to a component malfunction or discoloration (yellow). It may cause a fire hazard if not installed and maintained in accordance
with these instructions.
The thermal protection activation indicates that the unit has been subjected to abnormal operating conditions. If the thermal protection remains activated or activates
and deactivates repeatedly, it is recommended that a qualified electrician or a certified repair centre examine the unit in order to make sure it is not damaged. (Refer
to the limited warranty)
Before unplugging the unit, all controls must be in the “OFF” position and the current from the main breaker panel should be cut. (The general switch may be used
also, if included.) If the unit is damaged or defective, discontinue use, cut off power supply at circuit breaker and contact a certified electrician or certified repair centre.
(Refer to the limited warranty)
save these INSTRUCTIONS
technical drawings
20 1/8"
510mm
g
9 15/16"
253mm
g
21 3/4"
552mm
A
3/4"
19mm
1 3/4"
44mm
A
g
TOP
2 1/8"
53mm
3 3/4"
95mm
KO
7/8"
[22mm]
1 9/16"
40mm
3 1/2"
89mm
FRONT
SIDE A-A
2
1 3/4"
44mm
INSASKS0913
specifications, OPERATION & installation
specifications
kick space heater / ASKS series
VOLTS
120, 240
WATTS
500 or 1000 W (choice)
weight
10 lb / 4.5 kg
width
21 3/4" / 552 mm
height
3 3/4" / 95.3 mm
depth
9 15/16" / 253 mm
installation
N.B. Cut off power supply at circuit breaker/fuse before proceeding
to the installation and wiring connections. This product must be
connected by a certified electrician, according to the electrical and
building codes effective in your region. Consult the wiring plan found
on the unit.
To reduce the risk of fire, do not store or use gasoline or other
flammable vapors and liquids in the vicinity of the heater. Do not
mount in contact with combustible material. Do not mount in close
proximity to another unit.
Keep the front and and upper sides of the unit at least 3 feet (91 cm)
from any adjacent surfaces. Moreover, make sure objects or pieces
of furniture such as, but not limited to, blankets, towels, beds, laundry
baskets, clothing, papers, electric wires and other flammable items, do
not come into contact with the unit and keep them at least 3 feet (91 cm)
from the unit. Failure to comply with this warning could lead to a fire.
Some materials are more heat-sensitive than others, so make sure those
near the unit can withstand heat.
Important:
Place spacer
before installing
the device
figure 1
3 5/8"
92mm
20 3/8"
517mm
10"
254mm
MIN.
figure 2
1 - Cut the required opening according to the dimensions shown below.
(FIGURE 1)
2 - Unscrew the lid and open it. (FIGURE 2)
3 - Make the required electrical connections. Make sure to properly ground
the unit and to choose the desired power, according to the image below.
(FIGURE 3)
4 - Screw the lid in place. (FIGURE 2)
5 - Recess the unit into the cut opening and level it with a spacer.
6 - Secure the unit to the wall with wood screws (not supplied).
7 - Align the grill holes and secure it with the supplied screws.
N.B. This unit may be controlled by using either a wall thermostat
or a built-in mechanical thermostat (thermostat not included).
N.B. This unit is not meant to be installed into a floor recess.
figure 3
operation
warning: the heater must be properly installed before it is used.
Line : 1000W
circle : 500W
cabinet
Maximum
distance
4"
[102 mm]
3
INSASKS0913
maintenance & troubleshooting
maintenance
All other repairs and maintenance other than those
described in this guide should be performed by qualified
service personnel. In order for the warranty to be valid,
the unit must be cleaned regularly. Cut off power supply
at circuit breaker/fuse and wait for the unit to cool down
before cleaning.
Do not use cleaning products identified with these symbols:
Use a soft rag for dusting. When cleaning, use only a damp rag and
non-abrasive dish soap. Do not use abrasive or chemical cleaners
because they may damage the finish. If the unit is used in a very dusty
location, use a vacuum brush to remove dust and other foreign objects
from the grilles. Note that cigarette smoke could yellow the discharge
grille and that the best way to prevent it is to clean the unit on a regular
basis.
N.B. There is electrical current linked to the unit even if the
thermostat is set to off. This means that there is a risk of
electric shock as long as the unit is energized.
troubleshooting
PROBLem
DEFECTIVE PART OR PART TO CHECK
The unit does not work
• Defective thermostat or wrong thermostat setting
• Open circuit breaker or fuse
• The thermal protection has been activated
• Faulty connections
The unit runs continuously
• Defective thermostat or wrong thermostat setting
• Heat losses higher than the unit capacity
The enclosure is extremely hot
• Defective thermal protection
• Defective motor
• Blocked air vents
The desired room temperature cannot be reached
• One or more elements are defective
• Defective thermostat or wrong thermostat setting
• Voltage lower than that written on the nameplate
• Heat losses higher than the unit capacity
Room overheating
• Defective thermostat or wrong thermostat setting
The unit cycles under control of the thermal protection
• Blocked air vents
The breaker trips when the heater is turned on
• Faulty connections
• Voltage higher than that written on the nameplate
N.B. If you do not solve the problem after checking these points, cut off the power supply at the main electrical panel and contact
our customer service (see the “Limited warranty” section to obtain the phone numbers).
4
INSASKS0913
replacement component list
REPLACEMENT COMPONENT LIST
4
5
rEf. #
Part #
1
BLA-002
BLADE 5" 27' 4B
2
ECH150
CLOSED ELEMENT 500 W/120 V
2
ECH250
CLOSED ELEMENT 500 W/240 V
3
M-SKS12Z*
3
M-SKS14ZSS
4
MO-001
MOTOR 240 V
4
MO-012
MOTOR 120 V
5
PROT-005
6
SWI-006
6
Description
1
3
STANDARD SKS GRILL
Stainless steel SKS grill
THERMAL PROTECTION L-175
SWITCH
* Add A for almond, W for white, BK for black
2
A
optional
rEf. #
Part #
B
C
D
Description
A
SKSR**
RETROFIT SKS GRILL
B
SKST1
Single pole THERMOSTAT
c
SKST2
double pole THERMOSTAT
d
BOUT-015
ALMOND THERMOSTAT KNOB
d
BOUT-016
WHITE THERMOSTAT KNOB
d
BOUT-017
BLACK THERMOSTAT KNOB
** Add A for almond, W for white, BK for black, SS for stainless steel
5
INSASKS0913
limited warranty
This limited warranty is offered by Stelpro Design Inc. (“Stelpro”) and applies to the following product made by Stelpro: model ASKS. Please read
this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against defects in
workmanship and/or materials for the following periods from the date of purchase: 5 years (3 years on electronic components). This warranty
applies only to the original purchaser; it is non-transferable and cannot be extended.
ClaiM procedure
If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1)
your installer or distributor, 2) your service center or 3) Stelpro customer service department. In all cases, you must have a copy of the invoice
and provide the information written on the product nameplate. Stelpro reserves the right to examine or to ask one of its representatives to
examine the product itself or any part of it before honoring the warranty. Stelpro reserves the right to replace the entire unit, refund its purchase price or
repair a defective part. Please note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out by
persons authorized by Stelpro.
Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department
at: 1 800 363-3414 (electricians and distributors - French), 1 800 343-1022 (electricians and distributors - English), or 1 866 766-6020
(consumers). The authorization number must be clearly written on the parcel or it will be refused.
Conditions, exclusions and disclaimer of liability
This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims
and excludes any implied warranty of merchantability or implied warranty of fitness for a particular purpose.
Stelpro liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever, whether
based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions relating thereto.
Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages, penalties, special
or punitive damages, damages for lost profits, loss of use of equipment, cost of capital, cost of substitute products, facilities or services, shutdowns,
slowdowns, or for other types of economic loss or for claims of a dealer customer or any third party for such damages. Stelpro specifically disclaims all
consequential, incidental and contingent damages whatsoever.
This warranty does not cover any damages or failures resulting from: 1) a faulty installation or improper storage; 2) an abusive or abnormal use, lack of
maintenance, improper maintenance (other than that prescribed by Stelpro) or a use other than that for which the unit was designed; 3) a natural disaster
or an event out of the control of Stelpro, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage, flooding,
water damages, etc. This warranty does not cover any accidental or intentional losses or damages nor does it cover damages caused by negligence of
the user or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.
The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price, at the discretion of Stelpro. Any parts
replaced or repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty
period. This warranty will be considered null and void and Stelpro will have the right to refuse any claims if products have been altered without the
written authorization of Stelpro and if the nameplate numbers have been removed or modified. This warranty does not cover scratches, dents, corrosion
or discoloration caused by excessive heat, chemical cleaning products and abrasive agents. It does not cover any damage that occurred during the
shipping.
Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations on
how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may
have other rights which vary from state to state or from province to province.
limited warranty limited warranty limited warranty limited warranty limited warranty
Stelpro Design inc. | Saint-Bruno-de-Montarville | Québec | J3V 6L7
6
l i m i ted wa rra nty l i m i ted wa rra nty l im it ed warrant y limit ed warrant y
limit ed warrant y limit ed warra nty l i m i ted wa rra nty l i m i ted wa rra nty
limited warranty limited warranty limited warranty limited warranty limited warranty
INSASKS0913
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement