pumps &amp
PUMPS & IRRIGATION
Code# Description
728033 WaterPower 120 Pump
Rated GPH
951
MSRP
$128.75
Code#
728115
Rated GPH
1250
MSRP
$183.33
NEW!
WATERPOWER 120 PUMP
The waterPower pump has been designed for
ease of use. It is constructed with the highest quality workmanship and finest materials to ensure long dependable use.
• Magnetically driven centrifugal pump
• Max height: 13.8’
• No seals to wear out and contains no oil
• 1” NPT
• Use submerged or in-line
• Extra impller & sponge filter included
Description
TNC 1/4 hp Pump
TNC - 1/4 HP PUMP
The TNC centrifugal inline water pump is powerful and dependable. This water pump moves 1250 GPH through 1” pipe thread fittings and has a
dependable ceramic/graphite seal. The TNC water pump is used in the AeroFlo2 - 60 site units.
Code# Description
728475 Inline Water Pump - 120 watt
728480 Inline Water Pump - 135 watt
• Commercial grade ~ very powerful and
reliable
• In-line use (not submersible)
• Magnetic drive with ceramic shaft
Rated GPH
1140
1235
• Quiet & efficient
• Both pumps have standard 1” fittings– hard
plumb these pumps with standard 1” PVC
fittings
Code# Description
728075 Mag Drive Pump
•
•
•
•
190 GPH maximum flow
Max height 7’
10’ grounded power cord
Built-in adjustable flow control
Rated GPH
190
•
•
•
•
Code# Description
728065 Mag Drive Pump
•
•
•
•
250 GPH maximum flow
Max height 7’
10’ grounded power cord
Operates submerged or in-line
•
•
•
•
350 GPH maximum flow
Max height 10.5’
10’ grounded power cord
Operates submerged or in-line
Code# Description
728060 Mag Drive Pump
•
•
•
•
500 GPH maximum flow
Max height 10.5’
10’ grounded power cord
Operates submerged or in-line
Code# Description
728072 Mag Drive Pump
•
•
•
•
700 GPH maximum flow
Max height 12.5’
10’ grounded power cord
Operates submerged or in-line
MAG DRIVE PUMP 190 GPH
MSRP
$66.95
MAG DRIVE PUMP 250 GPH
MSRP
$77.95
MAG DRIVE PUMP 350 GPH
MSRP
$91.95
MAG DRIVE PUMP 500 GPH
MSRP
$102.95
MAG DRIVE PUMP 700 GPH
1/2” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Rated GPH
700
•
•
•
•
NEW!
1/2” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Rated GPH
500
•
•
•
•
NEW
LOWER
PRICES
1/2” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Rated GPH
350
•
•
•
•
MSRP
$46.95
INLINE WATER PUMPS
3/8” to 1/2” NPT
Ceramic shaft
Foam pre-filter & elbow included
Three year limited warranty
Rated GPH
250
Code# Description
728070 Mag Drive Pump
•
•
•
•
MSRP
$114.95
$131.95
1/2” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
WATER PUMPS
107
PUMPS & IRRIGATION
MAG DRIVE PUMP 950 GPH
Code# Description
728062 Mag Drive Pump
•
•
•
•
NEW!
MAG DRIVE PUMP 1200 GPH
NEW!
NEW!
NEW!
Rated GPH
1200
•
•
•
•
1800 GPH maximum flow
Max height 22’
10’ grounded power cord
Operates submerged or in-line
Rated GPH
1800
•
•
•
•
2400 GPH maximum flow
Max height 22’
10’ grounded power cord
Energy efficient
Operates submerged or in-line
Code#
728230
728232
728240
Description
Mag Drive Filter for 190 GPH
Mag Drive Filter for 250 - 700 GPH
Mag Drive Filter for 950 - 2400 GPH
MSRP
$5.19
$9.69
$13.69
MSRP
$13.99
$13.99
$17.99
$17.99
$25.99
$26.99
$41.99
$47.99
NEW!
Code#
728248
728250
728252
728256
728258
728260
728262
728264
Description
Mag Drive Impeller for 190 GPH
Mag Drive Impeller for 250 GPH
Mag Drive Impeller for 350 - 500 GPH
Mag Drive Impeller for 700 GPH
Mag Drive Impeller for 950 GPH
Mag Drive Impeller for 1200 GPH
Mag Drive Impeller for 1800 GPH
Mag Drive Impeller for 2400 GPH
MAG DRIVE PUMPS REPLACEMENT FITTINGS
NEW!
Code#
728268
728276
728282
Description
Fitting for 250 - 700 GPH ½” NPT x ½” Barb
Fitting for 950 - 1800 GPH ¾” NPT x ¾” Barb
Fitting for 2400 GPH 1” NPT x 1” Barb
Code# Description
727000 P-AAA Submersible Pump
Rated GPH
120
Permanently lubricated pumps for
commercial, industrial, and home use where
liquid must be transferred or recirculated. Applications include hydroponic systems, water gardens, ponds, etc.
• 6’ power cord • Corrosion-resistant housing
• Impedance protected
• Screened inlet
• 1/4” MNPT outlet, with 90° elbow accessory, accepts 1/2” I.D. tubing. • Manufacturer Item No. 523003
• Side intake
• One year limited warranty
108
WATER PUMPS
MSRP
$242.95
1” NPT
Ceramic shaft
Filled with epoxy, not oil
Pre-filter included
Three year limited warranty
MAG DRIVE PUMPS REPLACEMENT IMPELLERS
LITTLE GIANT® P-AAA SUBMERSIBLE PUMP
MSRP
$199.95
3/4” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Rated GPH
2400
•
•
•
•
•
MSRP
$176.95
3/4” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Code# Description
728085 Mag Drive Pump
•
•
•
•
•
MAG DRIVE PUMPS REPLACEMENT FILTERS
1200 GPH maximum flow
Max height 15’
10’ grounded power cord
Operates submerged or in-line
MSRP
$124.95
3/4” NPT
Ceramic shaft
Foam pre-filter included
Three year limited warranty
Code# Description
728080 Mag Drive Pump
•
•
•
•
MAG DRIVE PUMP 2400 GPH
•
•
•
•
Code# Description
728050 Mag Drive Pump
•
•
•
•
MAG DRIVE PUMP 1800 GPH
950 GPH maximum flow
Max height 15’
10’ grounded power cord
Operates submerged or in-line
Rated GPH
950
MSRP
$9.95
$9.95
$9.95
MSRP
$71.95
PUMPS & IRRIGATION
Code# Description
727005 PE-1 Submersible Direct Drive Pump
Rated GPH
170
MSRP
$77.49
LITTLE GIANT® PE-1 SUBMERSIBLE PUMP
MSRP
$116.95
LITTLE GIANT® 1-ABS SUBMERSIBLE PUMP
Small submersible epoxy encapsulated pump
for commercial, industrial and home use. Applications include hydroponic systems, water gardens, ponds, etc. This compact 170 GPH pump features
1/4” MNPT discharge, 7’ shut-off head capability, screened inlet and a 6’ power cord. Pumps are not recommended for fuel oil transfer, aquariums
and swimming pools.
• Inlet screen helps protect pump from debris
• 115 Volt
• 1/4” MNPT outlet accepts 1/2” I.D. flexible tubing
• 1/125 HP
• Impedance protected motor. • .3 amps
• 36 watts
• Manufacturer Item No. 518200
• Side intake
• One year limited warranty
Code# Description
727010 1-ABS Submersible Pump
•
•
•
•
•
•
Shallow-Pan Tank Style
Designed for in-pan mounting
Aluminum pump housing
1/4” MNPT discharge
Stainless steel shaft
Bottom intake
Code# Description
727015 1 Submersible Pump
Rated GPH
205
•
•
•
•
•
•
Integral float-activated switch
6’ power cord with 3-prong molded plug
Thermal overload protection
Manufacturer Item No. 550515
“On” in 1” & “Off” in 1/2” of water
One year limited warranty
Rated GPH
205
MSRP
$89.95
LITTLE GIANT® 1 SUBMERSIBLE PUMP
Permanently lubricated pumps for commercial, industrial, and home use where liquid must be transferred or recirculated. Applications include hydroponic
systems, water gardens, ponds, aquariums, etc. One year limited warranty.
• 1/4” MNPT outlet, with 90° elbow accessory, accepts 1/2” I.D. tubing.
• Epoxy-coated aluminum housing • Bottom inlet has snap-off screen for easy cleaning.
• Manufacturer Item No. 501003
• Bottom intake
Code# Description
727020 NK-1 Submersible Pump
Rated GPH
210
MSRP
$91.95
LITTLE GIANT® NK-1 SUBMERSIBLE PUMP
Permanently lubricated pumps for commercial, industrial, and home use where liquid must be transferred or recirculated. Applications include hydroponic
systems, water gardens, ponds, etc. One year limited warranty.
• Corrosion-resistant nylon housing • Sump-type screened inlet.
• 1/4” MNPT outlet accepts 1/2” I.D. tubing. • Thermally protected.
• Bottom or side intake
• Manufacturer Item No. 526003
Code# Description
727025 NK-2 Submersible Pump
Rated GPH
325
MSRP
$110.95
LITTLE GIANT® NK-2 SUBMERSIBLE PUMP
Permanently lubricated pumps for commercial, industrial, and home use where liquid must be transferred or recirculated. Applications include
hydroponic systems, water gardens, ponds, etc.
• 6’ power cord • Corrosion-resistant nylon housing
• Five position options • 1/4” MNPT outlet accepts 1/2” I.D. tubing.
• Thermally protected. • Manufacturer Item No. 527003
• Bottom or side intake
• One year limited warranty
Code# Description
727030 PE - 2.5F - PW Submersible Pump
Rated GPH
475
MSRP
$128.95
LITTLE GIANT® PE - 2.5F - PW SUBMERSIBLE PUMP
A premium pump at 475 GPH. Epoxy filled pump is compact in design, produces superior water flow and has corrosion resistant plastic housing. Ideal
for the water gardening environment.
• Usages: Circulating ponds up to 800 gallons, fountain nozzles, biological filters • 1 year limited warranty
• Corrosion resistant body designed for non-potable submersible use • Maximum Pumping Height 13.4’
• 1/2” MNPT Discharge • Accepts 3/4” ID Tubing
• Side intake
• Manufacturer Item No. 566633
Code# Description
727045 Piggyback Diaphragm Switch
MSRP
$71.95
LITTLE GIANT® RS-5LL DIAPHRAGM SWITCH
The RS5-LL switch can be used anytime you have a basin usage for the pump. It works by diaphragm. If the water reaches a certain level, it will shut
off the pump. The pump plugs into the switch. “On” level: 2”- 3”. “Off” level: .5” - 1.5” when mounted to 5-MSP. For pumps up through 1/3HP or the
following pumps, 5-MSP, 6-CIM-R, NK-1 & NK-2. 18’ cord.
WATER PUMPS
109
PUMPS & IRRIGATION
LITTLE GIANT® 5-MSP SUBMERSIBLE PUMPS
“Water
Wizard”
NEW COLOR
Code# Description
727035 5 - MSP Submersible Pump - Blue
727050 5 - MSPR Submersible Pump - Black
Permanently lubricated utility pump includes
garden hose adapter and removable inlet
screen for easy cleaning. Lifetime oil supply.
Pumps down to 1/8” (3.2 mm.).
• 1/6 HP thermally protected, shaded pole
motor
• Epoxy-coated cast aluminum housing
• Bottom inlet has removable screen for easy
cleaning
• Removes water down to 1/8”
LITTLE GIANT® 6 - CIM-R SUBMERSIBLE PUMP
MSRP
$147.95
$147.95
• 1” FNPT outlet includes garden-hose
adapter
• Manufacturer Item No. 505000
• Bottom intake
• One year limited warranty
Code# Description
727040 6 - CIM-R Sump Submersible Pump
Rated GPH
2760
MSRP
$202.95
Big John submersible sump pump for
residential and light commercial use, the 6-CIM-R manual sump pumps provides efficient and reliable service. Pump features a 1-1/2” discharge with
an 18’ maximum head. Cast iron motor housing is oil-filled for lifetime lubrication and rapid heat dissipation. Poly carbonate cover and polypropylene
volute-base. Garden Hose Adapter included for utility use.
• Mechanical shaft seal (stainless steel spring, nitrile parts, carbon and ceramic faces).
• Manual operation (pump can easily be converted to automatic operation using the RS-5, VDS1006, or RFSN-9 switches)
• 1/3 HP, 115 Volt, 10’ Power Cord • Screened inlet
• Oil filled motor housing for lifetime lubrication and rapid heat dissipation
• Stainless steel screws, bolts, and handle
• Epoxy coated cast iron motor housing for corrosion and rust resistance
• Thermal overload protection
• 1-1/2” MNPT x 1-1/4” FNPT (31.7mm) Reducer Bushing • Manufacturer Item No. 506271
• Bottom intake
• One year limited warranty
“Big John”
AIR MANIFOLDS
CHROME AIR MANIFOLDS
NEW!
High quality chrome air manifolds. Each outlet has individually controlled valves.
ECOPLUS® COMMERCIAL AIR PUMPS
•
•
•
•
ECOPLUS® AIR PUMPS & PARTS
Eco Air series pumps are very quiet, yet extremely powerful. They are long lasting and offer a
one year warranty. Controllable variable output on some models.
Replacement parts for the EcoPlus® Air Pumps. Each pump uses
the amount of diaphragms that is has outlets. For example the
Eco Air 4 has 4 diaphragms and valves. We suggest you replace
all diaphragms at the same time.
110
Rated GPH
1200
1200
WATER PUMPS/AIR DIFFUSERS/AIR PUMPS
Code#
728446
728447
728448
728449
Description
4 Outlet Air Manifold
6 Outlet Air Manifold
8 Outlet Air Manifold
10 Outlet Air Manifold
Use w/ Tube Use w/ Tube
Size - Inlet Size - Outlet
1/4” ID
3/16” ID
3/8” ID
3/16” ID
3/8” ID
3/16” ID
3/8” ID
3/16” ID
Code#
728460
728465
728470
Description
4 Valve Air Manifold
6 Valve Air Manifold
8 Valve Air Manifold
Use w/ Tube
Size - Inlet
1/4” ID
3/8” ID
3/8” ID
Code#
728450
728455
728457
Description
Commercial Air 1 - 38 Liter/min
Commercial Air 3 - 65 Liter/min
Commercial Air 5 - 88 Liter/min
Watts
18
35
80
MSRP
$1.49/ea
$2.95/ea
$3.49/ea
$4.95/ea
Use w/ Tube
Size - Outlet
3/16” ID
3/16” ID
3/16” ID
PSI
2.9
3.9
4.2
MSRP
$4.95
$6.95
$8.95
Tube Size
1/4” ID
3/8” ID
3/8” ID
MSRP
$52.95
$72.95
$91.95
Convenient to operate without oil or much noise with a single outlet.
Cylinders and pistons are made of excellent materials, making the pump strong, durable.
Will meet many requirements of pumps with air dividers from four to twenty-two outlets.
Widely used to provide oxygen in aquariums, fish farms & hydroponic systems. One year warranty.
Code#
728350
728355
728360
728365
728366
728361
Description
Eco Air 8 - Eight Outlets variable control
Eco Air 4 - Four Outlets variable control
Eco Air 2 - Two Outlets variable control
Eco Air 1 Plus - One Outlet
Eco Air 1 Plus Membrane & Valve
Eco Air 2, 4 & 8 Membrane & Valve
PSI Watts
2.2 24
1.7 12
1.7 6
1.7 3
Use Tube
Size
3/16” ID
3/16” ID
3/16” ID
3/16” ID
MSRP
$63.95
$32.95
$13.95
$8.95
$2.50
$4.99
MODEL
ECO AIR 8
ECO AIR 4
ECO AIR 2
ECO AIR 1
VOLT
FREQ
POWER (W)
OUTPUT (L/MIN)
OUTPUT (G/MIN)
PRESSURE (PSI)
WEIGHT (LBS)
DIMENSIONS (INCH)
110V
60Hz
24
20
5.2
2
5.0
4.5 x 7 x .125
110V
60Hz
12
9
2.3
1.75
2.6
7.75 x 5.7 x 4.2
110V
60Hz
6
4.5
1.2
1.75
1.3
6.5 x 3.75 x 3.4
110V
60Hz
2.5
2
.52
3
.39
3.4 x 1.8 x 2
PUMPS & IRRIGATION
Code# Description
GPH Use Tube Size
728040 Dual Diaphragm Air Pump
396 (air)
3/16” ID
728043 Dual Diaphragm Air Pump Rebuild Kit
MSRP
$64.98
$19.98
GENERAL HYDROPONICS DUAL DIAPHRAGM AIR PUMP
The Dual Diaphragm air pump is extremely
quiet and the only air pump in the world
manufactured exclusively for hydroponics systems. This high output pump has four adjustable ¼” outputs that can be teed off to power up to twelve air
driven hydroponics growing systems such as the WaterFarm. In addition, growers who use our Dual Diaphragm air pump can use it to reliably oxygenate
their reservoir with air stones. 3 psi, 320 gph (20 L/min). Rebuild kit includes two replacement diaphragms and two replacement lock nuts.
MSRP
$37.95
$44.95
$49.95
AERATOR
Code# Description
728730 Crystal Clear™ RO 100 GPD
728735 Crystal Clear™ RO 200 GPD
MSRP
$224.95
$324.95
CRYSTAL CLEAR™ REVERSE OSMOSIS UNITS
Code#
728740
728745
728750
728755
728760
MSRP
$109.95
$14.95
$17.95
$59.95
$19.95
Code#
728525
728530
728535
Description
Ario 2 Aerator
Ario 3 Aerator
Ario 4 Aerator
Watts
3.5
6
9
Reservoir Size
13 - 26 gal
26 - 40 gal
40 - 80 gal
Hydroponic growers know proper oxygenation
of your water will greatly improve the quality
of your crop. These new submersible aerators were designed as a quality alternative to what is currently available. The Ario line of aerators are so
powerful they actually create water movement within the reservoir. Everything you need to create optimum oxygen levels is packaged nicely in one
box. These silent aerators are manufactured in Italy & have a one year warranty.
Description
Crystal Clear™ Membrane
Crystal Clear™ Sediment Filter
Crystal Clear™ Carbon Filter
Crystal Clear™ Inline TDS Meter
Crystal Clear™ Float Valve ¼”
• 100 & 200 gallons per day high rejection thin film
membrane.
• Heavy duty clear canisters for holding filters.
• High capacity carbon & sediment filters.
• Provides bottled water quality.
• Includes garden hose adaptor & filter wrench.
• Quick disconnect fittings.
• Manual shut off valve on treated clean water line.
•
•
3 - Stage - 100
Gallons Per Day
Color coded lines for quick set up & easy identification.
Red - “In” for tap water
Black - Drain line for waste water
Blue - “Out” for treated, purified water
Improves the health of your plants & increases nutrient
uptake by removing harmful minerals, metals, &
pollutants from your water supply.
5 - Stage - 200
Gallons Per Day
Code#
728800
728805
728810
728815
Description
Hydro-logic™ Stealth 100
Hydro-logic™ Stealth Carbon Filter
Hydro-logic™ Stealth Sediment Filter
Hydro-logic™ Stealth Membrane
MSRP
$225.00
$16.50
$14.50
$83.00
HYDRO-LOGIC™ STEALTH 100
Code#
728820
728805
728810
728815
Description
Hydro-logic™ Stealth 200
Hydro-logic™ Stealth Carbon Filter
Hydro-logic™ Stealth Sediment Filter
Hydro-logic™ Stealth Membrane
MSRP
$315.00
$16.50
$14.50
$83.00
HYDRO-LOGIC™ STEALTH 200
MSRP
$189.00
HYDRO-LOGIC™ PRESSURE BOOSTER PUMP FOR STEALTH
Produces up to 100 GPD (gallons per day)
of ultra-pure, low PPM water. Removes
98%+ of chlorine & contaminants. Wastes
approximately 25% less water than other
RO Systems. Everything included in the box
for quick hook-up. Customized for gardening & hydroponics. *Based on 77˚ F 60 psi, 550 ppm inlet water. Includes: 3-Stage RO Unit, 1 RO Membrane,
Carbon Filter, Cleanable Sediment Filter, Automatic Shut-Off Cartridge, Wall Mountable Metal Bracket, Garden Hose Connector, lnline Shut-Off, 8 ft.
RO & Drain Line, 5 ft. Inlet Line, Filter Wrench and Instructions. Size: 15” x 14” Weight: 8.6 Ibs. Limited 1 year warranty.
Produces up to 200 GPD (gallons per day)
ultra-pure, low PPM water. Removes
98%+ of chlorine & contaminants. Wastes
approximately 25% less water than other RO
Systems. Everything included in the box for
quick hook-up. Customized for gardening & hydroponics. *Based on 77° F 60 psi, 550 ppm inlet water. Includes: 4-Stage RO Unit, 2 RO Membranes,
Carbon Filter, Cleanable Sediment Filter, Automatic Shut-Off Cartridge, Wall Mountable Metal Bracket, Garden Hose Connector, lnline Shut-Off / 8 ft.
RO & Drain Line, 5 ft. Inlet Line, Filter Wrench and Instructions. Size: 16.5’’ x 14” Weight: 9.8 Ibs. Limited 1 year warranty.
Code# Description
728897 Pressure Booster Pump For Stealth 100 & 200
This pump is designed to be installed before
the Stealth-RO to boost the inlet pressure. There needs to be at least 40 psi and up to 80 psi of inlet pressure for the Stealth-RO to function properly.
People on wells and other situations of low pressure can benefit greatly from this pump. It boosts the pressure significantly, allowing the Stealth-RO to
run with higher flow and efficiency while having better TDS removal. The pump is designed for long service life and runs very quietly.
AIR PUMPS/REVERSE OSMOSIS
111
PUMPS & IRRIGATION
HYDRO-LOGIC™ FLOAT KIT FOR MERLIN GP
Code# Description
728910 Float Kit For Merlin GP
MSRP
$42.00
This kit consists of a float valve with a 3/8” quick connect fitting and adjustable water level that can be mounted horizontally or vertically. Also
included is an automatic shut-off cartridge which help the Merlin-Garden Pro shut off both RO and drain lines. The kit allows you to fill a reservoir or
tank, unattended, to your desired water level.
HYDRO-LOGIC™ PRESSURE BOOSTER PUMP FOR MERLIN GP
Code# Description
728895 Pressure Booster Pump For Merlin GP
MSRP
$329.00
This pump is designed to be installed before the Merlin-Garden Pro to boost the inlet pressure. There needs to be at least 40 psi and up to 80 psi of
inlet pressure for the Merlin-Garden Pro to function properly. People on wells and other situations of low pressure can benefit greatly from this pump.
It boosts the pressure up to 70 psi allowing the Merlin-Garden Pro to run with higher flow and efficiency while having better TDS removal. The 5
diaphragm pump, specifically design for the Merlin, is a workhorse but runs quietly. Comes with 120v cord and 1/2” quick connect fittings.
HYDRO-LOGIC™ TDS INLINE MONITOR FOR MERLIN GP
Code# Description
728900 TDS Inline Monitor
MSRP
$75.00
Highly efficient and accurate due to its advanced microprocessor technology. Auto-Off function conserves battery power. The unit shuts off automatically
after 20 seconds. Dual range - measures from 0-999 ppm, with a resolution of 1 ppm. From 1000 to 9990 ppm, the resolution is in 10 ppm increments,
indicated by a blinking image. Comes factory calibrated. Comes equipped with 3/8” & 1/2” Quick Connect T-fittings for Merlin Garden Pro™ or Tall BlueMerlin™ for quick install. Measure the untreated water coming in vs. the purified water going out of your reverse osmosis system at any time. Limited
3 year warranty.
HYDRO-LOGIC™ TALL BLUE
Code#
728860
728865
728870
Description
Hydro-logic™ Tall Blue
Hydro-logic™ Tall Carbon Filter - 20”
Hydro-logic™ Tall Sediment Filter - 20”
MSRP
$159.00
$31.00
$14.00
Prefilter for Merlin GP. Removes up to 99% of chlorine and 90% of sediment, rust, silt, etc. Filters chloramines and particulates down to 5 microns.
Includes: 2-Stage 20” Pre-Filter Unit / Wall Mountable Metal Bracket / 4 ft. Feed Line to Merlin-Garden Pro™ / Filter Wrench / Instructions / Size: 11” x
24” Weight: 11 lbs / Limited 1 year warranty
HYDRO-LOGIC™ SMALL BOY
Code#
728875
728880
728885
Description
Hydro-logic™ Small Boy
Hydro-logic™ Small Boy Carbon Filter-10”
Hydro-logic™ Small Boy Sediment Filter-10”
MSRP
$105.00
$14.00
$11.00
Code#
728890
728865
728870
Description
Hydro-logic™ Tall Boy
Hydro-logic™ Tall Carbon Filter - 20”
Hydro-logic™ Tall Sediment Filter - 20”
MSRP
$179.00
$31.00
$14.00
Removes up to 99% of chlorine and 90%
of sediment, rust, silt, etc. @ 1 GPM. Easily
produces 60 gallons per hour of clear water filtered down to 5 microns. Filter capacity of 3,000 gallons.
Includes: 2-Stage 10” Filter Unit / Wall Mountable Metal Bracket / Garden Hose Connector / 4 ft. Feed Line / 6 ft. Outlet Line / 1/4” Shut-off / Filter
Wrench / Instructions / Size: 11 “ x 14” Weight: 6.4 Ibs / Limited 1 year warranty
HYDRO-LOGIC™ TALL BOY
Removes up to 99% of chlorine and 90% of sediment, rust, silt, etc. @ 2 GPM. Easily produces 120 gallons per hour of clear water filtered down to 5
microns. Filter capacity of 7,500 gallons.
Includes: 2-stage 20” Filter Unit, Wall Mountable Metal Bracket, Female Garden Hose Connector, Brass Male Garden Hose Connector, 4 Ft. Feed Line, 4 Ft.
Outlet Line, Filter Wrench, Instructions, Size: 11” x 24” Weight: 11 lbs & Limited 1 year warranty
HYDRO-LOGIC™ FLOWMASTER FLOW METER
Code# Description
728905 Flowmaster Flow Meter
MSRP
$54.00
The Flowmaster measures how many gallons of filtered water have gone through the system and alerts you when it’s time to change filters. You can
program in the filter capacity and when you reach the target number of gallons, the Flowmaster beeps. Important for knowing when to change the
pre-filter for the Merlin-Garden Pro. Also ensures your system runs at its peak efficiency at removing contaminants. Available in 3/8” quick connect
for the Merlin-Garden Pro & Tall Boy and in 1/4” for the Small Boy.
112
REVERSE OSMOSIS UNITS
PUMPS & IRRIGATION
Code#
728840
728845
728850
728855
Description
Hydro-logic™ Merlin GP
Hydro-logic™ Merlin GP Carbon Filter
Hydro-logic™ Merlin GP Sediment Filter
Hydro-logic™ Merlin GP Membrane
MSRP
$589.00
$32.50
$23.00
$142.00
HYDRO-LOGIC™ MERLIN GP
Produces 30 gallons per hour or 750 gallons
per day of ultra pure, low ppm water.
Removes 95%+ of chlorine, hardness
(calcium & magnesium), excessive minerals
(iron), and all other contaminants. Wastes approximately 40% less drain water than other RO systems on the market. Everything included in the box to
start producing bottled quality water for your plants. Exclusive configuration for hydroponics and gardening, not available anywhere else! * Based on
77° 50 psi, 750 ppm feed water. Includes: High-Flow Reverse Osmosis Unit with 1 Carbon Pre-filter & 2 RO Membranes, Inlet Pressure Gauge, Garden
Hose Connector & 3.8” lnline Shut-off, 12.5’ RO Line, 4.5’ Feed Line, 4.5’ Drain Line and Instructions. Size: 10” x 17” x 20”, Weight: 29 lbs, Limited 3
year (Residential), 1 year (Commercial) warranty
Code# Description
MSRP
728581 Aqua Heat™ Titanium Reservoir & Aquarium Heater - 200 watt $34.49
728582 Aqua Heat™ Titanium Reservoir & Aquarium Heater - 300 watt $36.49
•
•
•
•
Heater tube is fully submersible
Automatic electronic heater
Double heating tube
Very durable and reliable
•
•
•
•
AQUA HEAT™ TITANIUM RESERVOIR & AQUARIUM HEATERS
Easy temperature control
Ideal for saltwater & freshwater
Temp range: 68°F (20°C) to 93°F (34°C)
One year warranty
ECOPLUS® WATER CHILLERS
The EcoPlus® Chillers are suitable for use in reservoirs, hydroponic systems & fresh or saltwater aquariums. Each chiller provides a high performance titanium heat exchanger for optimum performance and
corrosion resistance. High quality made compressor is extremely efficient and reliable. The micro computer with digital LCD display allows for easy operation. Use with a pump filter bag (product #728188
or # 728190). One year limited warranty on all EcoPlus® chillers.
IMPORTANT: Allow all Chillers to set upright, on their feet for 30 minutes prior to plugging in.
Code# Description
728695 EcoPlus® 1∕10 HP Chiller
728715 Replacement 1/10 HP Chiller Fitting Kit
•
•
•
•
Fittings: 1/2”
Weight: 31 lbs. Wattage: 280/Amps: 2.3
Capable of Chilling:
MSRP
$419.95
$7.95/ea
93 gallons - 10° F
35 gallons - 30° F
•
•
•
•
Dimensions: 10.5” W x 12” D x 14” H
Voltage: 120V/60Hz BTU: 950
Pump Size:
Minimum 132 GPH
Maximum 264 GPH
Code# Description
728700 EcoPlus® ¼ HP Chiller
728720 Replacement ¼ HP Chiller Fitting Kit
•
•
•
•
Fittings: 3/4”
Weight: 48.5 lbs. Wattage: 480/Amps: 4
Capable of Chilling:
MSRP
$549.95
$9.95/ea
170 gallons - 10° F
100 gallons - 30° F
•
•
•
•
Fittings: 1”
Weight: 68 lbs. Wattage: 540/Amps: 4.5
Capable of Chilling:
Code#
728405
728410
728415
728420
728425
728430
320 gallons - 10° F
220 gallons - 30° F
Description
Large Round Air Stone
Medium Round Air Stone
Small Round Air Stone
EcoPlus® 8” Air Stone
EcoPlus® 6” Air Stone
EcoPlus® 4” Air Stone
MSRP
$949.95
$11.95/ea
•
•
•
•
ECOPLUS® 1∕4 HP Chiller
Dimensions: 13” W x 15” D x 16” H
Voltage: 120V/60Hz BTU: 2200
Pump Size:
Minimum 633 GPH Maximum 1056 GPH
Code# Description
728702 EcoPlus® ½ HP Chiller
728725 Replacement ½ HP Chiller Fitting Kit (No fuse)
•
•
•
•
ECOPLUS® 1∕10 HP Chiller
ECOPLUS® 1∕2 HP Chiller
Dimensions: 15” W x 18.5” D x 15” H
Voltage: 120V/60Hz BTU: 5400
Pump Size:
Minimum 750 GPH Maximum 1200 GPH
Use Tube Size
1/4” ID
1/4” ID
1/4” ID
3/16” ID
3/16” ID
3/16” ID
MSRP
$4.95
$2.95
$1.95
$1.95
$1.49
$1.29
ECOPLUS® AIR STONES
MERLIN GP/RESERVOIR HEATERS/CHILLERS/AIR STONES
113
PUMPS & IRRIGATION
MICRO-PORE™ AIR DIFFUSERS
728509
Code#
728500
728506
728505
728507
728508
728509
728505
728507
728508
728500
728506
ECOPLUS® FLEXIBLE AIR DIFFUSERS
•
•
•
•
Description
Single Air Diffuser
Single XL Diffuser
Double Air Diffuser
Double XL Diffuser
“Hog” 2X Diffuser
“Boss Hog” 2 X Diffuser
Use Tube Size
3/16” ID
3/16” ID
1/4” ID
1/4” ID
1/4” ID
1/4” ID
MSRP
$20.95
$26.95
$36.95
$42.95
$41.95
$64.95
Kiln fired ceramic material will not react with nutrients solutions
Micro-Pore design produces smaller, more prolific bubbles
Will not clog or break down like other compressed silicates diffusers
Extends the life of nutrient solutions for all types of hydroponics
Code#
728435
728440
728445
Description
2’ Flexible Air Diffuser
3’ Flexible Air Diffuser
4’ Flexible Air Diffuser
Use Tube Size
3/16” ID
3/16” ID
3/16” ID
MSRP
$4.59
$6.19
$7.95
These air “hoses” are flexible and unbreakable. They provide excellent aeration. To clean, just wipe off under running water.
Code# Description
728565 EcoPlus® Aquarium & Reservoir Thermometer
ECOPLUS® AQUARIUM & RESERVOIR THERMOMETER
MSRP
$2.49
• Glass tube precisely made of German • Suction cup to stick to the inside of an • Thermometer floats in water
material
aquarium or reservoir
FITTING KIT
706750
706751
ECOPLUS® EBB & FLOW FITTINGS
1” Tub
Outlet Fitting
1/2” Tub
Outlet Fitting
3/4” Tub
Outlet Fitting
Outlet
Extension
Code# Description
706750 Fitting Kit with Adapter
706751 Teal Fill/Drain Fitting Adapter
Code#
708560
708565
708570
708575
708580
Description
Outlet extension
Screen
½” Tub outlet fitting (13mm)
¾” Tub outlet fitting (19mm)
1” Tub outlet fitting (25mm)
MSRP
$9.95/ea
$3.95/ea
Pcs/Bag
10
10
10
10
10
MSRP
.74¢/ea
.64¢/ea
$2.40/ea
$2.70/ea
$3.10/ea
Pcs/Bag
25
25
25
25
25
1
MSRP
$1.50/ea
$1.55/ea
.50¢/ea
.50¢/ea
.20¢/ea
$4.85/ea
• Manufactured using the finest quality materials.
• All pieces offered a la carte for maximum flexibility.
Screen
BOTANICARE® EBB & FLOW FITTINGS
• Interior threads which accept ¾” standard
pipe thread.
• Use as ebb and flow fittings & bulkhead
fittings.
• Increased versatility: thread PVC pipe
fittings into bulkhead fittings - ideal for
use in aeroponic and drip applications.
Code#
708551
708552
708553
708554
708555
708556
Description
Ebb & Flow ½” Barbed Fitting
Ebb & Flow ¾” Barbed Fitting
Ebb & Flow Extension Fitting
Ebb & Flow Screen Fitting
Ebb & Flow Fitting Washer
Ebb & Flow Fitting Kit with 2 Extensions
BARBED REDUCER
Code# Description
708055 3/4” to 1/2”
ECOPLUS® 1/4” & 1” BARBED CONNECTORS
Code#
708405
708410
708415
708460
708465
708470
114 AIR DIFFUSERS/IRRIGATION SUPPLIES
Description
1/4” (4mm) Tee
1/4” (4mm) Straight
1/4” (4mm) Elbow
1” (25.4mm) Tee
1” (25.4mm) Straight
1” (25.4mm) Elbow
MSRP
.75¢/ea
Bag Count
10
10
10
10
10
10
MSRP
.38¢/ea
.24¢/ea
.36¢/ea
$1.38/ea
$1.18/ea
$1.30/ea
PUMPS & IRRIGATION
Code#
708420
708425
708430
708435
708440
708445
708450
708455
Description
1/2” (13mm) Tee
1/2” (13mm) Straight
1/2” (13mm) Elbow
1/2” (13mm) Inline Valve
3/4” (19mm) Tee
3/4” (19mm) Straight
3/4” (19mm) Elbow
3/4” (19mm) Inline Valve
Bag Count
10
10
10
10
10
10
10
10
MSRP
.50¢/ea
.46¢/ea
.52¢/ea
$3.20/ea
$1.14/ea
.96¢/ea
$1.04/ea
$3.50/ea
ECOPLUS® 1/2” & 3/4” BARBED CONNECTORS & VALVES
Code# Description
708700 “Y” Filter with 100 micron screen ¾” Inlet & Outlet
708705 100 micron replacement screen
RD #
60400UB
MSRP
$14.03/ea
RAINDRIP® “Y” FILTER WITH ¾” INLET & OUTLET
603010
$3.97/ea
Code#
708600
708605
708610
708615
708620
Description
½” Compression Tee
½” Compression Coupling
½” Compression Elbow
½” Compression Hose End Plug
½” Compression Valve
Rain Drip Eaches/
Number
Card
R305CT
2
R310CT
2
R315CT
2
R303CT
1
R617CT
1
MSRP
$2.05/ea
$1.42/ea
$1.64/ea
$2.43/ea
$4.51/ea
RAINDRIP® ½” COMPRESSION FITTINGS
708600
708605
708610
708615
708620
All Raindrip® fittings are made in the USA of quality materials for optimum performance. Raindrip®
fittings are interchangeable with competitive systems. Made from ABS plastic. For use with 1/2” hose
and water pressure up to 60 psi.
Code#
708625
708626
708630
708631
708635
708636
Description
½ GPH Drippers Blister Card
½ GPH Drippers Bag
1 GPH Drippers Blister Card
1 GPH Drippers Bag
2 GPH Drippers Blister Card
2 GPH Drippers Bag
Rain Drip Eaches/
Number
Pack
R108CT
10
PC2025B
25
R110CT
10
PC4025B
25
R112CT
10
PC8025B
25
MSRP
.78¢/ea
.49¢/ea
.78¢/ea
.49¢/ea
.78¢/ea
.49¢/ea
RAINDRIP® DRIPPERS
708625
708626
708630
708631
708635
708636
Raindrip®’s “turbulent flow” PC (pressure compensating) drippers maintain their rated flow rate
for 10-60 psi inlet pressure. These drippers can be used at the end of 1/4” tubing feeders or can be
inserted directly into 1/2” Raindrip® hose.
Code#
708640
708645
708650
Description
4” Support Stakes
6” Support Stakes
1/2” - 5/8” Hose End Clamps
Rain Drip Eaches/
Number
Card
R380CT
10
R381CT
10
R301CT
5
MSRP
.22¢/ea
.33¢/ea
.51¢/ea
RAINDRIP® STAKES & CLAMP
708645
708640
708650
4” support stakes are plastic stakes that hold 1/4” tubing in place next to plants. 6” support stakes are
heavy duty plastic stakes that hold 1/4” lines in place. The hose end clamps close off ends of 1/2” or
5/8” poly hose.
Code#
708655
708657
708660
Description
1/4” Poly Tubing 50’ Roll
1/4” Poly Tubing 1000’ Roll
1/2” Poly Tubing 50’ Roll
RD #
016005P
016100
052005P
RAINDRIP® POLY TUBING
MSRP
$5.39/ea
$65.95/ea
$10.69/ea
Professional quality hose is made from linear, low-density polyethylene (poly). Composed of 2.2%
carbon black and UV inhibitors, it can be left year round, buried or on the surface, in any weather.
Superior to hose made from reprocessed materials.
708657
708655
708660
NEW!
IRRIGATION SUPPLIES/RAINDRIP PRODUCTS
115
PUMPS & IRRIGATION
RAINDRIP® CUTTER & HOLE PUNCHES
Code#
708665
708670
708675
Description
Professional Tubing Cutter
Hole Punch - Black
Professional Hole Punch
RD #
63200UB
R630CT
63100UB
MSRP
$11.23/ea
$3.55/ea
$11.20/ea
The professional tubing cutter has a hardened stainless steel blade that is designed to cut all flexible plastic hose/tubing
up to 1.5” outside diameter. Both the hole punch & professional hole punch are designed for comfortable use. They punch
holes in 1/2”, 5/8” or .710” hose to insert PC drippers or 1/4” fittings. The black hole punch includes 10 hole plugs.
RAINDRIP® WATER TIMER & ACCESSORIES
Code#
708680
708685
708690
Description
Analog Electronic Timer
3/4” Pressure Regulator
3/4” Swivel x 1/2” Hose Adaptor
RD #
R672CT
R460CT
R320CT
MSRP
$44.88/ea
$10.80/ea
$2.57/ea
Raindrip®’s single station battery-operated analog water timer is for 3/4” faucet/hose spigot hook-up. Large control knobs
for easy set-up. Features adjustable frequency & run times. The pressure regulator has a ¾” inlet & outlet. It maintains 1520 psi for circuits totalling up to 360 GPH. The adaptor connects ½” poly hose to a faucet or other ¾” male hose thread.
RAINDRIP® 3 OUTLET MANIFOLD TRIPLE SHUT-OFF
Code# Description
708695 3 Outlet Manifold Triple Shut-off
RD #
61900UB
MSRP
$2.73/ea
Converts one faucet to three separately controllable outlets. 3/4” female hose thread inlet x 3/4” male hose threaded outlets.
SPRAYERS & SPINNER
706392
Code#
706392
708195
708200
708190
708195
708190
708200
TUBING
Code#
708215
708220
708222
708223
708225
708230
708235
708245
708250
708251
Description
Clear Tubing
Black Tubing
Clear Tubing
Black Tubing
Blue Tubing
White Tubing
Black Tubing
Black Tubing
White Tubing
Black Tubing
NEW!
DRIPPER STAKE 45°
Description
EZ-Clone™ 360° Sprayer
180° Sprayer
360° Sprayer
360° Clone Spinner
MSRP
.70¢/ea
.70¢/ea
.70¢/ea
$1.75/ea
These spinners are used in high output aeroponic gardening applications.
A rotating 360° sprayer that is ideal for rooting cuttings aeroponically. The spinner comes complete with
a male thread for a secure, no leak fit. (Used in Clone Machines).
Roll
Length
100 ft.
100 ft.
100 ft.
100 ft.
100 ft.
100 ft.
100 ft.
100 ft.
100 ft.
50 ft.
Inside
Diameter
3/16”
3/16”
1/4”
3/8”
1/2”
1/2”
1/2”
3/4”
3/4”
1”
Outside
Diameter
1/4”
1/4”
3/8”
1/2”
5/8”
5/8”
5/8”
1”
1”
1 1/4”
MSRP
$11.95
$29.95
$23.95
$35.95
$34.95
$41.95
$36.95
$104.95
$121.95
$77.95
Typical Uses
Airline for EcoPlus® 1, 2, 4 & 8 pumps
Irrigation drip line
Airline for Commercial Air 1 pump
Airline for Commercial Air 3 & 5 pumps
Irrigation line/hydroponics
Irrigation line/hydroponics
Irrigation line/hydroponics
Irrigation line/hydroponics
Irrigation line/hydroponics
Irrigation line/hydroponics
Code# Description
708350 Dripper Stake 45°
MSRP
.41¢/ea
This angled dripper stake fits 1/4” irrigation tubing and has a 45° angle to reduce sharp bending of the tubing, which causes clogging. It
delivers a light emission of water for regular top drip irrigation.
DRIPPER STAKES
116
RAINDRIP/IRRIGATION SUPPLIES
Code# Description
708280 Dripper Stake with 1/8” dripper line
MSRP
.75¢/ea
PUMPS & IRRIGATION
Code# Description
708340 Dripper Stake with Basket
708345 Dripper Line ¼” x 15”
DRIPPER STAKES & LINE
MSRP
.41¢/ea
.30¢/ea
708345
708340
Code# Description
740090 Water Alarm with Sensor
• Warns of leaks and overflows in reservoirs, aquariums or anywhere there
is a potential for leaks
• Low battery signal tells user when it’s time to replace the battery
• Circuit test bar ensures system is working
• An ideal backup system for sump and bilge pumps in residential,
commercial & marine applications
MSRP
$18.95
• Alerts user within hearing range that water has reached desired level
when used to monitor the filling of pools, reservoirs, aquariums and
more
• Sensor and alarm can be placed up to 6 feet apart
• Loud 85 dB (decibel buzzer). Sounds for up to 3 days
• One year warranty
Suction cup side for mounting
directly to side of reservoir
Code#
708300
708305
708310
708315
Description
1/4” (6mm) Grommet
1/2” (13mm) Grommet
5/8” (16mm) Grommet
3/4” (19mm) Grommet
Code#
708320
708321
708325
708330
Description
Eaches/Bag MSRP
1/2” Grommet - GH
25
.68¢/ea
1/2” Grommet - GH
500
.51¢/ea
1” Grommet - GH (Aeroflo Chamber Sprayline)
10
$1.90/ea
1-1/4” Grommet - GH (Aeroflo Chamber Drain)
10
$2.20/ea
Code# Description
708170 Float valve
WATER ALARM WITH REMOTE SENSOR - Detects Water & Sounds Alarm
MSRP
.80¢/ea
.70¢/ea
.85¢/ea
$1.10/ea
GROMMETS
These grommets can be used to replace old,
worn grommets in your hydroponic systems
and are essential components when making
a system from scratch.
GROMMETS
FLOAT VALVE
MSRP
$16.00
An essential part for do-it-yourselfers! This float valve assembly controls the water/nutrient solution level in your primary reservoir (controller). Comes
with 1/2” brass barbed fitting.
Code#
708005
708010
708020
Description
1/2” Clic Clamp
3/4” Clic Clamp
1” Clic Clamp
MSRP
.69¢/ea
.95¢/ea
$1.10/ea
Code# Description
708180 1/8” Hose punch
MSRP
.75¢/ea
CLIC CLAMPS FOR TUBING
Ensures a secure hose connection. Easy
to use.
HOSE PUNCH
Tough enough to punch a hole in thick, flexible tubing. Makes a 1/8” hole specifically for drip lines.
Code#
706115
Description
Aqua Shuttle Kit
AQUA SHUTTLE KIT
MSRP
$26.95
Used to convert an Ebb and Flow system to
a drip system.
IRRIGATION SUPPLIES/WATER ALARM
117
ENVIRONMENTAL CONTROLLERS
CO2 TEST KITS
Code# Description
702305 CO2 Test Kit
702300 CO2 Detector Tubes
702300
702305
MSRP
$19.95/ea
$40.95/box
Product 702305 includes: 1 - 100cc syringe, 2 - rae systems test tubes & instructions.
Product 702300 has a range: 300 - 5000 ppmv, Sample Volume: 100 ml, Sample Time: 2 min., Color: White to Purple.
Box contains 10 tests.
NEW!
TITAN CO2 CONTROLLER
Code# Description
702700 Titan CO2 Controller
MSRP
$449.95
The Titan CO2 Controller is an affordable, easy to use and dependable controller. It uses a Telaire brand control device
which is a General Electric company. You can count on this unit for years of reliable, trouble-free use. It will provide you
accurate levels of CO2 in your growing area. The PPM range is 0 to 5000. To use, simply plug your CO2 tank valve or burner
into the piggyback cord. The Titan CO2 Controller will automatically maintain the CO2 level that you specify on the unit.
This control device will work with any C02 generation system that is operated by 120 volt power. Three year warranty.
TITAN CO2 REGULATOR
NEW FALL 2008
Code# Description
702710 Titan CO2 Regulator
702712 Replacement White Plastic Washer
• Compatible with Titan Controls CO2 Controller (#702700) or other
120 volt controllers & timers
• Precision Accuracy Flow Meter - .5 to 15 SCF/hour
• CO2 helps increase overall plant growth
• Features heavy-duty solenoid valve
• Brass construction for long-lasting dependability and durability
NEW!
OPTIMUM GROWTH CO2 SYSTEMS
702010
GAS METER
702015
•
•
•
•
•
MSRP
$147.95
.99¢/ea
Includes 12’ of CO2 dispensing line
Powered by 6’ - 120 volt grounded power cord
Two plastic tank washers included
High quality oil-less pressure gauge
3 Year Warranty
Code# Description
702010 Optimum Growth CO2 System
702015 Optimum Growth CO2 System with Timer
MSRP
$169.95
$229.95
A quick release system designed to keep your room at its ideal CO2 levels for plant growth. Use the Optimum Growth CO2 System
with the Controller or with your existing cycle timer. Don’t have a timer? Purchase the Deluxe System which incorporates a built-in
cycle timer. Optimum Growth Systems are designed to bring the PPM of CO2 to its optimal level in under 10 minutes and refill as
needed. Using the Optimum Growth Deluxe CO2 System with a temperature/humidity/CO2 controller will give your grow-room
its ideal CO2 levels whenever the exhaust fan isn’t running, while maintaining the proper temperature and humidity.
NEW!
Code# Description
702313 Gas Meter
MSRP
$28.95
Never run out of propane! Use this device to quickly see the level of propane in your tank. For all propane appliances with
type 1 connection
• Emergency flow restrictor in case of a major leak.
• Low gas indication prevents unnecessary cylinder exchange or refills.
• Leak detection protects environment from gas emissions.
3 Year
Warranty
Since 1998, Sentinel has been providing the best and most reliable controllers and timers
you can buy. Visit www.growgps.com for more product information & tutorial videos.
NEW!
DRT-1 – DIGITAL RECYCLING TIMER
Code# Description
702500 DRT-1/Digital Recycling Timer
MSRP
$124.95
100% digital recycling timer. Allows the user to set the on & off times in hours, minutes & seconds. No complex menus, single function push buttons
for ease of use. Photocell allows daytime, nighttime or 24-hour operation. Two receptacles control up to 15-amps of power. Memory backed up with
lithium battery. Re-settle circuit breaker built-in. 15 amps @ 120 volts, 32 to 120° F, 0-99% RH, Day, Night or 24-hour +/- 12 seconds/year, 1 second,
23 hours, 59 min, 59 sec.
118
CO2 ACCESSORIES/CO2 SYSTEMS
ENVIRONMENTAL CONTROLLERS
Code# Description
702505 MDT-1/Master Digital Timer
MSRP
$209.95
NEW!
MDT-1 – MASTER DIGITAL TIMER
100% digital lighting & recycling timer that
combines 2 main timing functions in one convenient package. Control lighting schedules with 24-hour time clock. The MDT-1 has an integrated digital
recycling timer can operate daytime, nighttime or 24 hours a day. Digital recycling on & off times can be programmed in hours, minutes and seconds.
The Hi-Temp shutdown feature allows the user to set a maximum temperature. In the event of overheating, the MDT-1 will shut off the lighting. If
overheating event happens, the unit logs the max temperature and the time it occurred. Hot start prevention monitors the incoming power and will
disable the HID lights in the event of a power failure. After a user selectable delay, the HID lamps are permitted to re-start. 15 amps @ 120 volts, 32 to
120° F, 0-99% RH, Day, Night or 24-hour +/- 12 seconds/year, 1 second, 23 hours, 59 min, 59 sec.
DIGITAL CONTROLLERS
Code#
702510
702515
702520
702525
702530
702535
702540
702532
702545
702550
Description
COOL-1/Cooling Thermostat
UTC-1/Universal Temperature Controller
EVC-1/Environmental Controller
EVC-2/Environmental Controller
CHHC-1/Total Environmental Controller
HPH-4/High Power HID Controller
HPH-8/High Power HID Controller
CPPM-1/CO2 Controller with integrated photocell
PXM-1/Power Expansion Module 120 Volt
PXM-2/Power Expansion Module 240 Volt
MSRP
$69.95
$144.95
$199.95
$299.95
$669.95
$169.95
$249.95
$549.95
$92.95
$112.95
NEW!
DIGITAL CONTROLLERS FROM SENTINEL
A simple device to control the temperature of an area. Any
cooling device that operates on 120 volts and is 15-amps or less
can plug into the COOL-1. Once connected to the COOL-1, the
device is turned on & off when the temperature changes. Very
similar to the thermostat in your home. Set the temperature you
want to maintain, and the thermostat activates when it senses
a change in temperature. 15 amps @ 120 volts, 50 to 115° F,
Deadband 5 degrees F, > 10 years, 15-amps / 3/4 HP
Simple to use, 100% digital temperature controller. Photocell
allows separate day and night temperature settings. Record &
recall minimum and maximum temperature levels. Features a
heating or cooling mode with adjustable deadband and 16 ft remote probe. 15 amps @ 120 VAC, 32 to 120 degrees F, UTC-1 +/- 15’F
The EVC-1 provides extreme flexibility in reliable solid-state environmental controller. Selectable CO2, temperature and humidity modes allow the user to control
temperature & humidity separately or together. Built-in photocell activates C02 device during the day. Night device outlet can control an exhaust fan/sulfur burner, etc. 15
amps @ 120 VAC, 32 to 120 degrees F, 0-99% rH, +/- 2’ F, +/- 7% rH
The EVC-2 controls your temperature & humidity with digital accuracy. Photocell allows day/night temperature
& humidity settings and also provides daytime CO2 operation. The remote combination temperature &
humidity probe allows the probe to be placed near plant canopy. It records & recalls minimum and maximum
temperature & humidity levels. The EVC-2 has two temperature modes, heating & cooling with separate
humidity control to add or remove humidity. Adjustable temperature deadband. 15 amps @ 120 VAC, 32 to
120 degrees F, 0-99% rH, +/- 1’F, +/- 3% rH
The CHHC-1 controls all of your growing area conditions accurately & reliably. It has all of the CO2 control features of the CPPM-1. It also has the ability
to control 3 other devices, a cooling device, a heating device and a humidity device. This controller is simple to use. You can set separate day and night
temperature settings as well as humidity settings. Records the min and max temperature, humidity and CO2 levels. The CHHC-1 can be calibrated by the
user with our "self calibration feature".
The HPH-4 High Power HID controller allows the user to connect up to (4) 1000 watt HID ballasts to one main control “relay”. It is designed to safely
control HID lights from a single 30-amp power source. It accomplishes this by using a 16 foot “trigger” cable that connects to a timeclock or the MDT-1.
When the timer connected to the trigger cable turns on, the heavy-duty relay inside the HPH-4 is energized. When the relay is energized, the lights are
turned on. 30-amps @ 240 VAC, 120 VAC, 16 foot, Nema 1-15, 4000 watts, Four (4) ballasts, Heat sink cast aluminum, >10 years
702535
702540
The HPH-8 High Power HID controller allows the user to connect up to (8) 1000 watt HID ballasts to one main control “relay”. It is designed to safely
control HID lights from a single 50-amp power source. It accomplishes this by using a 16 foot “trigger” cable that connects to a timeclock or the MDT-1.
When the timer connected to the trigger cable turns on, the two heavy-duty relays inside the HPH-8 is energized. When the relays are energized, the
lights are turned on. 50-amps @ 240 VAC, 120 VAC, 16 foot, Nema 1-15, 8000 watts, Four (8) ballasts, Heat sink cast aluminum, >10 years
The CPPM-1 controls your carbon dioxide levels with part-per-million accuracy. It uses a CO2 sensor that is extremely accurate and features a ten-year life
expectancy. Our combination CO2 & light level sensor is housed in a separate remote sensor enclosure that can be located up to 100 ft from the controller.
The CPPM-1 can also be connected to other controllers so that the CO2 is disabled (useful when operating exhaust fans). It can be operated in fuzzy-logic
mode (for compressed CO2), or on-off (for CO2 generators).
702545
Power Expansion Modules increase the number or size of lights, fans, air conditioners and pumps in your growing area that can be automated. Install
the PXM by connecting the pre-wired trigger cable into any controller or timer that is 120 volts. Then locate a suitable circuit and plug in the pre-wired
#14 gauge cable into the power outlet of your choice. Plug the devices that are to be controlled into the PXM and you are ready to go. The PXM-1 is
15-amps @ 120 VAC, 120 VAC, 16 foot, Nema 1-15, 1200 watts, 14,000 BTU @ 120 Volt. The PXM-2 is 15 amps @ 240 VAC, 120 VAC, 16 foot, Nema
1-15, 2400 watts, 24,000 BTU @ 240 Volt.
702550
SENTINEL CONTROLLERS
119
ENVIRONMENTAL CONTROLLERS
CO2 REGULATORS & GENERATORS
NEW!
CO2-REG & CO2-EXP
Code# Description
702555 CO2-REG/CO2 Regulator
702560 CO2-EXP/Expansion Regulator
MSRP
$144.95
$79.95
The CO2-REG controls the flow of CO2 and regulates the
amount with a precision flow gauge that can be set from
1/2 – 15 SCFH (standard cubic feet per hour). The color coded pressure gauge is easy to read and understand. Comes with 6 foot power cord and 120 volt solenoid
pre-wired. Ready to connect to a controller or timer. Can be used with either 20 lb or 50 lb CO2 cylinders. It reduces the pressure from the cylinder from over 2000
psi down to 30 psi. Maximum inlet 3000 psi.
Designed to be used with the CO2-REG. Using the CO2-EXP together with the CO2-REG allows 2 tanks to be connected and
controlled. Extend time between required tank charges. The connection to the CO2-EXP is low pressure making installation safe
and easy. The CO2-EXP comes with it’s own easy to read gauge & 1/4” interconnecting hose.
VARIABLE CO2 GENERATORS
NEW!
Code#
702565
702567
702570
702572
Description
VCG-27 LP/Propane CO2 Generator
VCG-27 NG/Natural Gas CO2 Generator
VCG-6 LP/Propane CO2 Generator
VCG-6 NG/Natural Gas CO2 Generator
Gas burning CO2 generators are the
most cost effective way of producing
CO2. The VCG series of generators are
the safest and most advanced CO2
generators available.
• 2 models available, Propane (LP) & Natural Gas (NG).
• Variable CO2 output from 6-27 cu ft CO2/hr.
• Solid-state electronic ignition control module eliminates the open
pilot flame.
• Tip-switch shuts of the gas flow when it falls.
• Unit comes with 10 brass burners pre installed.
MSRP
$649.95
$649.95
$469.95
$469.95
• Brass burners are designed to burn clean and produce consistent
blue flames.
• Open “air-cooling” module available.
• Dual redundant low-voltage solenoid valves add a second layer of
safety.
• Complete with 12 foot hose and pressure regulator.
GREEN AIR PRODUCTS
ATMOSPHERIC CONTROLS MULTI-FUNCTION
Code#
702330
702335
702340
702345
Description
Integrated Cooling Thermostat & Dehumidistat/4 Outlets
Synchronized Cooling Thermostat/Dehumidistat/4 Outlets
Model CT-DH-3P with light activated photosensor
Model CT-DH-4P Independent Cooling Thermostat/
Dehumidistat/4 Outlets
702350 Independent Cooling & Heating Thermostat/4 Outlets
702355 Microclimate Controller System/8 Outlet
This CT-DH-1 is designed to turn “On” and
“Off” exhaust fans and/or intake fans to remove
unwanted atmosphere due to heat or humidity.
Internal sensors will allow a 7° temperature
comfort zone and a 7% humidity span (differential)
between the time the fans go “Off” and come back
“On” again. When either temperature or humidity
exceeds the dial settings, all four outlets will turn “ON”, activating any cooling or exhaust equipment plugged into the controller.
The CT-DH-3 was primarily developed to be used with CO2 equipment and exhaust type fans. Internal sensors will allow a 7° temperature comfort zone
and a 7% humidity (differential) between the time the fans go “Off “and come back “On” again. Temperature or humidity raise will activate the right hand
outlets and deactivate the left hand outlets. The CT-DH-3 has an internal relay that automatically switches power from the left side (CO2 Outlets) to the
right side (Exhaust Outlets) of the unit when either temperature, humidity or both are in excess of the dial settings. The left side of the controller is normally
in the “ON” position and is able to activate CO2 equipment as needed.
MSRP
$205.00
$240.00
$300.00
$300.00
$205.00
$835.00
702340
The CT-DH-4P is designed to be used with CO2 equipment, dehumidifiers, and exhaust fans. It offers independent outlets for temperature & humidity
control. It is ideally suited for use with dehumidifiers. Temperature raise will activate the right hand outlets and deactivate the CO2 outlet. Humidity
rise will activate the dehumidifying outlet. Internal sensors will allow a 7° temperature comfort zone and a 7% humidity (differential) between the
time the equipment goes “Off “and comes back “On” again. The CO2 outlet is normally in the “On” position and is able to activate CO2 equipment as
needed, but is defeated when exhaust function is active. The photosensor will defeat CO2 enrichment during darkness hours.
This controller features fully independent sensors for cooling and heating equipment. The cooling thermostat activates the left outlets of the controller and
the heating thermostat activates the right outlets. If you require a tighter control of your temperature than the internal heating\cooling thermostats allow,
alternate sensors are available with a 3º differential External Coil or Remote Bulb Thermostat.
The Micro Climate Controller MCC-1 is designed to perform all the major atmospheric and timed functions required in an automated growth environment
including temperature, humidity, carbon dioxide enrichment, lighting and irrigation control. The controller incorporates an external coil cooling thermostat
, a dehumidifying humidistat, a 24-hour clock timer, a photo-sensor and a repeat cycle timer. Automatic override and defeat systems coordinate controls
to consider all possible variables. All connections are standard 3-prong grounded plugs and receptacles. Operates on 110VAC with 15 Amp switching
capacity.
120
SENTINEL CO2/GREEN AIR CONTROLLERS
ENVIRONMENTAL CONTROLLERS
Code# Description
702377 Tempstat Thermostat 3º F - Heating & Cooling
702375 Total Humidity Controller - Humidify & Dehumidify
ATMOSPHERIC CONTROLS SINGLE-FUNCTION STATS
MSRP
$155.00
$155.00
The Temp H/C Temperature Controller is switchable
between heat and cool. Perfect for plant zone
environments, reptile habitats or any other application requiring automatic switching of heating and cooling equipment. The black anodized aluminum
enclosure is durable and attractive and will never corrode or discolor from hot, cold or humid environments. Available with 3º or 7º differential span or
7º Remote Bulb Thermostat. This control operates AC, exhaust fans, evaporative coolers, heaters or other temperature equipment by activating switches,
motors, valves or pumps. Temperature range 40º to 110º F (5º to 45º C)
Control humidity automatically and accurately with the THC. It can be switched between humidify and dehumidify to remove unwanted atmospheric moisture
accumulating within an enclosed area or add needed moisture by means of humidification.
In the dehumidifying mode high humidity conditions will activate fans or other apparatus until level drops approximately 7% in relative humidity. At this
point dehumidifying equipment is disabled until humidity increases again 7%. In the humidifying mode this control operates fogging or other equipment
by activating switches, motors, valves or pumps. Humidifiers can be precisely controlled according to atmospheric humidity to create ideal conditions for
any environment.
Code# Description
702379 Chronometric Sequential Timer
702385 Repeat Cycle Timer
TIMERS – CYCLE TIMERS
MSRP
$275.00
$190.00
The CST-1 has solved the age old problem of
accurate short cycle timing. The only unit of it’s
kind designed specifically for the control of grow systems. Easy to set and operate. Solid state time counter with adjustable frequency and duration. The
CST-1 function timer has many uses and only a few of them include: fogging or misting, spray stakes or drip system timing, air pumps, CO2 equipment
and intake\exhaust fan control.
The Cyclestat 4P is perfect for plant zone environments, reptile habitats or any other application requiring automatic short cycle switching. Easy to set and
operate. Microprocessor time counter with adjustable frequency and duration. The Cyclestat 4P timer has many uses. Only a few of them include: fogging
or misting, spray stakes or drip system timing, air pumps, CO2 equipment and intake or exhaust fan control. The Cyclestat may be set for interval and cycle
of timed events. Interval is the time between “ON” cycles. The interval knob may be set from 5 minutes to 8 hours. Set this for desired time between
functions. Cycle is the length of time that a specific function or condition must be maintained. Cycle may be set from 5 seconds to 30 minutes.
TIMERS – LIGHTING TIMERS
These time switches are designed to operate high load lighting equipment. Operates with a maximum combined outlet switching capacity of 40 amps. Plug or wire the power cord into a receptacle capable
of handling the maximum total combined amperage draw of your equipment load. Plug lighting equipment into outlet receptacles located on each side of controller. Timer has 96 non-detachable 15 minute
on\off trippers.
Code#
702390
702395
703400
Description
4 Light Timer - 120 Volt (Model LT4-120)
4 Light Timer - 240 Volt ( Model LT4-240)
8 Light Timer - 240 Volt ( Model LT8-240)
The LT4-120 provides four 10 amp 120 volt outlet receptacles, each capable of powering up to 1000
watts of lighting equipment. The LT4-240 offers four 10 amp 240 volt outlets and will power lighting
equipment up to 1000 watts each. The LT8-240 provides eight 5 amp 240 volt outlet receptacles, each
capable of powering up to 1000 watts of lighting equipment.
Code# Description
703405 24 Hour Timestat Controller
LIGHT TIMERS
MSRP
$335.00
$400.00
$465.00
702395
702390
MSRP
$150.00
702400
24 HOUR TIMESTAT CONTROLLER Model TSC-1
The TSC-1 timer is a 24 hour time switch that
provides accurate timing with 96 non detachable trippers for On/Off functions adjustable in 15 Minute increments up to 48 cycles per day. Constructed with
durable, black anodized, aluminum housings that will never corrode or discolor for hot, cold or humid environments. This unit can be used independently
or as part of a combination of control devices to coordinate numerous system functions. Precision synchronous clock motor provides 15 amp 110 volt
control for pumps, fans lighting, solenoids, motors relays or virtually any equipment or appliance dependent upon multiple daily operations.
CO2 MONITORS & CONTROLLERS
Code# Description
702404 Bottle CO2 Regulator & Solenoid
MSRP
$325.00
BOTTLED CO2 REGULATOR & SOLENOID Model BCDE-1
Green Air Products bottled CO2 emitter
systems combine a forged brass flow gage regulator with a UL/CE/CSA certified emitter solenoid valve. These systems offer a flow range from 7-20
SCFH. Comes with 10 feet of clear tubing with spring clamps, a grounded 6ft 120 volt power cord.
GREEN AIR CONTROLLERS
121
ENVIRONMENTAL CONTROLLERS
CO2 CONTROLLERS
Code#
703423
703415
703420
Description
CO2 Set Point Controller
CDDS-2 & CDM-6000 Sensor
CDDS-2 & CDM-7001 Sensor
MSRP
$665.00
$990.00
$1,395.00
This easy to install and to operate CO2
enrichment controller is factory calibrated
and inspected for optimum performance.
The SPC-1 is designed with a photo sensor
to defeat CO2 enrichment during dark periods and a large easy to read real-time LED display. The SPC-1 also is programmed with a preset differential
(hysteresis) of 20 PPM and offers an elevation adjustment feature to fine tune performance. The SPC-1 is constructed with durable components and a
rust and scratch resistant, black anodized aluminum chassis. Operates on 120 Volt AC with 12 Amp switching capacity.
The CDMC-6 system is designed to sample the air and learn the characteristic of your space, then make adjustments as necessary to ensure a constant
level of CO2. The CDM-6000 monitor employs a passive infrared sensor which samples the air once every second and then sends the sample data to the
CDDS-2 sequencer. The CDDS-2 then activates or deactivates your CO2 enrichment or venting (exhaust) equipment to maintain desired CO2 PPM. The
CDDS-2 uses a sophisticated adaptive algorithm or “Overshoot Protection Logic” to learn the dynamics of the space being controlled. This allows the
systems to avoid dramatic overshoots inherent to set point controllers or timed CO2 enrichment. These learned parameters are stored in the memory,
even when the ‘POWER’ is off, or until you reset the unit.
The CDMC-6 system offers a large LCD screen displaying the current CO2 levels in PPM. Set your desired CO2 level, ‘Hysteresis’ and ‘Elevation’ to
maintain precise levels without guesswork. The CDMC-6 system can be using for enriching or venting CO2 and incorporates a photosensor to defeat
CO2 during dark periods (Night).
The CDMC-7 system functions like the CDMC-6 for CO2 enrichment or ventilation, but offers the added features of a portable monitor in the CDM7001 with dual beam absorption infrared technology and a LCD display that shows CO2 PPM and real time temperature. The CDM-7001 monitor is
also equipped with a computer interface to download CO2 history. Recorded data can be graphed and printed using a Windows based VG graphing
software (not included).
CO2 GENERATORS WITH LP RATED HOSES
Carbon dioxide generators operate by burning carbonaceous fuels such as propane or natural gas. The burners used in Green Air Products CO2 generators are specially designed to maximize the production
of CO2 and minimize heat as a by-product. These generators provide CO2 far more economically than any other means of enrichment. A constant burning pilot is used to ignite the gas when the generator
is turned on. A thermocouple is used to monitor the pilot flame. If the pilot flame is lost, a safety valve will close so that unburned fuel will not be released into the enclosure. CO2 Generator operations may
be automatically functioned according to actual ambient values when installed in conjunction with the CDMC. The generators may be controlled with timers such as the Cyclestat 4P. Transformer included.
Operates on 110 volt AC.
LIQUID PROPANE & NATURAL GAS CO2 GENERATOR MODELS
Code#
703430
703435
703440
703450
703455
703460
703465
703475
GREEN AIR REPLACEMENT PARTS
Code# Description
703476 Replacement 12 Volt AC/DC Adaptor
702435 Replacement CO2 Hose
Description
CD-3LP - CO2 Generator 3 cu. ft. per hour Propane
CD-6LP - CO2 Generator 6 cu. ft. per hour Propane
CD-12LP - CO2 Generator 12 cu. ft. per hour Propane
CD-36LP - CO2 Generator 36 cu. ft. per hour Propane
CD-3NG - CO2 Generator 3 cu. ft. per hour Natural Gas
CD-6NG - CO2 Generator 6 cu. ft per hour Natural Gas
CD-12NG - CO2 Generator 12 cu. ft. per hour Natural Gas
CD-36NG - CO2 Generator 36 cu. ft. per hour Natural Gas
MSRP
$510.00
$600.00
$685.00
$845.00
$545.00
$620.00
$700.00
$865.00
MSRP
$26.50
$55.00
Replacement AC/DC adaptor for CO2 generators. Replacement hose for use with all Green Air Generators
PLUG N GROW PRODUCTS
iGS-011 CYCLE TIMER WITH PHOTOCELL
Code# Description
703500 iGS-011 Cycle Timer with Photocell
The iGS-011 cycle controller represents an easy solution to periodic control
day and night or just day only. The integrated photocell can differentiate
day and night.
122
GREEN AIR CO2/PLUG N GROW CONTROLLERS
•
•
•
•
ON time from 30 seconds to 60 minutes
OFF time from 1 minute to 12 hrs
Maximum load : 120 volt AC, 15 Amp, 1 HP
Now features 3 year warranty.
MSRP
$99.00
ENVIRONMENTAL CONTROLLERS
Code#
703502
703510
703550
Description
iGS-012 High Temperature Watchdog
iGS-021 Day & Night Temperature Control
iGS-070 Manual Plug-in Variable Speed Control
MSRP
$109.00
$109.00
$79.00
TEMPERATURE CONTROLLERS & SPEED CONTROLLER
Plug iGS-012 in the 110-120 volt wall socket
chosen to supply your lighting equipment. Plug
lighting equipment in 110-120 volt output of the
iGS-012 (maximum charge of 15 Amps). Keep
temperature sensor far of any source of heat. Temperature sensor should be located above the floor level and near top of plant canopy.
• Can control lighting equipment plugged in a iLS4-120, iLS4-120S or iLS4-240 by connecting sense cord of iLS4 to iGS-012. The iLS4-120, iLS4-120S
and iLS4-240 can be connected in a row to control many pieces of lighting equipment.
• Now features 3 year warranty.
The iGS-021 temperature controller will operate your heating or cooling equipment in accordance to user day and night set points. Does not have a display.
Now features 3 year warranty.
This module enables the user to adjust fan speed manually. Works only with magnetically driven fans. Connect up to 750 watts to a single unit. Now
features 3 year warranty.
Code#
703505
703515
703520
703525
703530
703535
Description
iGS-010 Day & Night Cycle Timer with Photocell & Display
iGS-020 Day & Night Temperature Control with Display
iGS-020 with Remote
iGS-030 Day & Night Humidity Control with Display
iGS-030 with Remote
iGS-040 Day & Night Cooling & Humidifying Control with
Display
703540 iGS-040 with Remote
MSRP
$189.00
$189.00
$199.00
$229.00
$239.00
$279.00
$289.00
TEMPERATURE & HUMIDITY CONTROLLERS
The iGS-010 cycle controller represents an easy
and flexible solution to periodic control of day and
night. The integrated photocell can differentiate
day and night and will initiate the proper day or
night periodic control.
• ON time from 5 seconds to 60 min
• OFF time from 1 minute to 12 hours
• Maximum load : 120 volt AC, 15 Amp, 1 HP
• Now features 3 year warranty.
The iGS-020 temperature controller will operate your heating or cooling equipment in accordance to user day and night set points. The ambient temperature
is displayed on the luminous bar graph. The precision temperature sensor (1° C) can be calibrated and the differential of operation is adjustable. This controller
is also available with a remote (10 feet) sensor (iGS-020R).
• ±1°C precision temperature sensor
• 0° to 40° C control range
• Maximum load: 120 volt AC, 15 Amp, 1 HP
• Now features 3 year warranty.
The iGS-030 relative humidity controller will operate your humidifying or dehumidifying equipment in accordance to user day and night set points. The
ambient relative humidity is displayed on the luminous bar graph. The precision RH sensor (3%) can be calibrated and the differential of operation is
adjustable. This controller is also available with a remote (10 feet) sensor (iGS-030R).
• 3% precision RH sensor
• 0-100% RH control range
• Maximum load: 120 volt AC, 15 Amp, 1 HP • Now features 3 year warranty.
The iGS040 Cooling and dehumidifying controller will operate your inlet and/or exhaust fans (or any other cooling and/or dehumidifying equipment) in
accordance to user temperature and relative humidity day and night set points. Temperature and relative humidity values can be viewed in real time on
the luminous bar graph. The differential is factory preset to ± 2.5% for RH and ± 1° C for temperature. Of course these values can be increased by the user.
This controller also offers the user a low temperature limit which when set will interrupt the equipment in the case of excessive cooling. This controller is
also available in remote (10 feet) sensor format (iGS040R). Now features 3 year warranty.
Code# Description
703560 iGS-110 Day & Night Temperature & Relative Humidity Control
MSRP
$439.00
DAY & NIGHT TEMPERATURE & RELATIVE HUMIDITY CONTROL
Model iGS-110
The iGS-110 temperature and relative humidity controller is essential to good climate control in a grow room or greenhouse. The display shows the
ambient temperature (Celsius and Fahrenheit) and relative humidity values. The internal sensors benefit from a fast sampling rate. The control unit
can be positioned up to 6 feet from the output box (a cable up to 50 feet can be used). Multiple operation modes are available and the differential of
operation is adjustable. This unit is 120 volts and uses 12 watts of power.
Maximum load both outputs: 15 Amp 120 volt AC RH Sensor and control range: 0%-100%
Auto differential adjustment: 3 to 10%
Annual drift: <1%
Accuracy of RH sensor: ±3%
Calibration of RH sensor: factory calibrated
Temperature sensor and control range: -20° C to +50° C (-4°F to +122 ° F) Accuracy of temperature sensor: ±1° C (±2° F)
Auto. Differential adjustment: 1° C to 10° C (-1.8° F to +18° F) Resolution of temperature sensor: 0.5° C (1° F)
Calibration of temperature sensor: factory calibrated
Now features 3 year warranty.
PLUG N GROW CONTROLLERS
123
ENVIRONMENTAL CONTROLLERS
CO2 CONTROL WITH HIGH TEMPERATURE SHUT OFF FUNCTION
Code# Description
703545 iGS-061 CO2 Control with High Temperature Shut Off
MSRP
$639.00
The iGS-061 will perform CO2 enrichment during the day only (when light is sensed by the photocell). The enrichment starts when the CO2 concentration
falls below the set point minus the differential. The differential modifies itself until the controller senses no more overshooting or undershooting of
user set point. Fixed differential values can also be set for more specific needs. As a safety feature, the high temperature shut off function will inhibit
operation while temperature is over the user setting. This interruption is maintained until temperature falls below the user high temp setting. To inhibit
this feature, simply set the limit to its highest value. The controller can also be set to vent (extract) CO2. In this case, the high temp shut off feature
becomes a low temp shut off limit to prevent excessive cooling conditions. Now features 3 year warranty.
CO2 CONTROL WITH AUXILIARY SHUT OFF OUTPUT
Code# Description
703555 iGS-100 CO2 Control with Auxiliary Shut Off Output
MSRP
$769.00
The iGS-100 CO2 controller is a tool to
efficiently and economically use CO2 enrichment for higher growth rates or to fulfill minimum ventilation needs day and night. The display shows
the ambient CO2 concentration within ±75 ppm at all times. The internal CO2 infrared sensor reads values from 0 to 5000 ppm. The air sampling is
optimized by means of an integrated fan. The control unit can be positioned up to 6 feet from the output box (a cable up to 50 feet can be used). The
controller will automatically adjust its operating differential when the CO2 concentration overshoots or undershoots the desired set point. Two set
points are used by the controller : day and night set points. This unit is 120 volts and uses 12 watts of power. Now features 3 year warranty.
Maximum load both outputs: 15 A 120 volt AC Battery-backed microprocessor control
Sensor and Control range : 0-5000 ppm Automatic differential compensation: ± 20 ppm Annual drift of the CO2 sensor: ± 75 ppm Calibration of the CO2 sensor: 1 year
DAY & NIGHT CO2, RELATIVE HUMIDITY & TEMPERATURE
SMART CONTROL - Model iGS-220
Code# Description
703565 iGS-220 Day & Night CO2, RH & Temperature Smart Control
MSRP
$999.00
The iGS-220 CO2 relative humidity and temperature controller integrates climate management and CO2 enrichment or venting. The electronic module
displays the actual values of the CO2, relative humidity and temperature sensors. Includes an internal fan to speed up the air sampling process thus
yielding better climate control. The control unit can be positioned up to 6 feet away from the output box (a cable up to 50 feet can be used). The control
unit logs the last 24 hours min, max and average. CO2 concentration, relative humidity and temperature values. Multiple operation modes are available
and the differential of operation is adjustable. 3 year warranty.
Battery Backed microprocessor (36 hrs battery) Power supply: 120 volt AC
Consumption: 00 mA 12 watt
Temperature Sensor & control range : -20° C to +50° C (-40°F to +122° F) Accuracy of the temperature
Max. load both outputs: 15 A 120 volt AC
CO2 Sensor and Control range: 0 - 5000 ppm Annual drift: ±20 ppm
Auto differential adjustment: 50 to 800 ppm Accuracy of the CO2 Sensor: ±75 ppm Annual drift: ±1° C (2° F)
Calibration of the CO2 Sensor: 1 yr Sensor: 0.5° C (1° F) RH sensor and control range: 0 - 100% RH
Annual drift: < 1%
Auto differential adjustment: 3 to 10% Accuracy of the RH sensor: ±3%
Calibration of the RH sensor: Auto differential adjustment: 1° C to 10° C (-1.8°F to +18° F), Calibration of the temp Sensor & Unit: Factory calibrated
LIGHTING LOAD SWITCH BOXES & SWITCH RELAY
703580
703575
This switching module will switch up to four
1000 watt lights using a low power 120 volt
AC trigger cord. An internal On-delay timer
can be set to prevent hot bulb startups or
set to sequentially turn on groups of up to
four lights. Model iLS4-120S is powered by
a 240 volt AC circuit but delivers 120 volt AC
to lighting ballasts (4 wires necessary from
breaker assembly). Model iLS4-240 supplies
240 volt AC to your equipment. Features 3
year warranty.
IGS CO2 GENERATORS & GENERATORS WITH HEAT EXCHANGERS
•
•
•
•
•
Safety panels to avoid burning.
Safe, easy to use and highly energy efficient.
Safe electronic pilot: no manual starting button nor continuous flame.
Internal electronic control to avoid excessive heating & to turn off the unit in case of tipping over.
Dimensions: 16.5” D x 20.5” H x 9.5” W
124 PLUG N GROW CONTROLLERS & GENERATORS
Code# Description
MSRP
703575 iLS4-120S Light Load Switch With Internal 0-20 Minute On Delay $229.00
240 volt Supply, 120 volt Output
703580 iLS4-240 Light Load Switch with Internal 0-20 Minute On Delay $239.00
240 Volt Outputs
703590 iLS120-OFF Plug-in 12 amps on-switched relay with low current $89.00
120 volt trigger cord
This 120 volt AC Module can switch off 120 volt AC
equipment while another is being activated. Switch
off fans, while CO2 or sulfur vaporizing is in progress
or dehumidifier when fans are on. Easy to set-up. Now
features 3 year warranty.
Code#
703700
703705
703710
703715
703720
703725
703730
703735
Description
IGS-LP4 CO2 Generator LP-12,000 BTU
IGS-NG4 CO2 Generator NG-12,000 BTU
IGS-LP8 CO2 Generator LP-24,000 BTU
IGS-NG8 CO2 Generator NG-24,000 BTU
IGS-LP4X CO2 Generator w/ Heat Exchanger LP-12,000 BTU
IGS-NG4X CO2 Generator w/ Heat Exchanger NG-12,000 BTU
IGS-LP8X CO2 Generator w/ Heat Exchanger LP-24,000 BTU
IGS-NG8X CO2 Generator w/ Heat Exchanger NG-24,000 BTU
MSRP
$849.00
$879.00
$929.00
$969.00
$959.00
$989.00
$1,079.00
$1,129.00
• Heat exchanger helps keep a cooler temperature inside the greenhouse or grow room without
affecting the CO2 and humidity levels.
• Use 6” ducting to exhaust heat from unit.
• Heat exchanger may be ducted to supply heat to living space (fan suggested) without introducing
CO2.
ENVIRONMENTAL CONTROLLERS
Code# Description
703600 iMS100 Automatic dialer & movement detector alarm
AUTOMATIC DIALER & MOVEMENT DETECTOR ALARM
MSRP
$269.00
The iMS100 is a security system which will detect intruders and fires in your home, office, business or wherever it is set up. It is designed to give you
an early warning by calling up to 6 pre-stored phones/pager with your own voice message. It is simple to set up and use, and will monitor your home
or business without any monthly charge. Now features 3 year warranty.
SOLATEL PRODUCTS
Code#
703605
703610
703612
Description
HGC-2 Plant Pro™ Controller without CO2
HGC-3 Plant Pro™ Controller with CO2
EXT-2 Extension Cable Set (4ea - 15 ft)
PLANT PRO™ ENVIRONMENTAL CONTROLLER
MSRP
$622.95
$995.00
$35.00
Precision electronic control for all environmental variables. Outlets for lighting, irrigation, ventilation,
and CO2. High accuracy sensors for temperature, humidity, and flood. Optional Photocell (light) and
CO2 sensors available. Sensors have flexible 10 foot cables (25 foot total with optional extensions).
This allows the Plant Pro™ to be located for easy monitoring and adjustment, even outside the grow
room, if desired. The Plant Pro™ unique simplified operation allows for easy, quick setup using only two
control knobs and a large digital display. One knob to select a setting, a display to show the setting, and
a second knob to change the setting. Measurements from sensors can also be displayed. Easy to use
digital clock provides exact timing. CO2 control includes timed or optional CO2 sensor. Adjustable fan
CO2 delay allows extra time for CO2 absorption by plants before ventilation fan comes on.
Code# Description
703607 CO2 Sensor (Special Order)
703609 Photocell Sensor (Special Order)
MSRP
$490.95
$30.95
Code# Description
703608 Flood Detector Stand Alone (Special Order)
MSRP
$149.95
Product No. 703612
NEW!
REPLACEMENT SENSORS
These are replacement sensors for the Plant Pro Environmental Controller.
NEW!
FLOOD DETECTOR
Detects overflow of water or nutrient if pipe breaks or drains clog. Two 120V 15A outlets: one ON when sensor wet, other ON when sensor dry. One
outlet could turn on an alarm during a flood. The other outlet could turn off a nutrient pump during a flood. Two second delay minimizes false alarms.
Sensor has 10 ft. cable. Hold Switch selects automatic or manual reset when wet sensor dries out. Manual reset requires user to reset switch for outlets
to respond to dry sensor.
Code# Description
703614 CO2 300 (Special Order)
MSRP
$599.95
NEW!
CO2 300 CARBON DIOXIDE CONTROLLER
Simply set the desired CO2 level and the CO2-300 does the rest. The Sensor Unit has a display and 3 buttons (SET, +, and -). Normally it displays actual
room CO2 PPM (Parts Per Million).
Using the buttons, you can display and change the set point (also in PPM). The Sensor Unit is connected to the Control Unit by an 8 foot cable. The
Control Unit plugs into any 120V outlet. If you wish to defeat CO2 dispensing when your lamp is off, plug the Control Unit into your lamp timer or a
timer running the same schedule. The CO2 dispensing equipment (tank solenoid valve or generator) plugs into the 120V outlet on the front of the
Control Unit.
Code# Description
703613 THP 100 Atmospheric Controller
MSRP
$259.95
NEW!
THP 100 ATMOSPHERIC CONTROLLER
The Solatel THP-100 coordinates ventilation and CO2 (carbon dioxide). This is required when temperature and humidity are controlled by a vent or
exhaust fan. Hot or humid air is blown out of the growing area and fresh air is then drawn in. This continues until both temperature and humidity fall
below the dial settings. CO2 is only dispensed during the day when plants have light for photosynthesis. It is not dispensed when the fan is operating
because this would waste CO2. The THP-100 provides all of these functions. When connecting CO2 equipment, a repeat cycle timer or CO2 concentration
controller (not included) is plugged into the THP 100. The CO2 tank valve or CO2 generator then plugs into the timer or controller.
SOLATEL CONTROLLERS
125
ENVIRONMENTAL CONTROLLERS
PWX-1 & PWX-D20 POWER EXPANDERS
Code# Description
703615 PWX-1 Power Expander - 120 Volt 15 amp
703622 PWX-D20 Power Expander (20 second delay)
MSRP
$98.95
$149.95
Code# Description
703620 PWX-240-6 Power Expander - 240 Volt 30 amp
703621 PWX-240S Power Expander (sequential)
MSRP
$249.95
$299.95
Power Expanders allow you to turn on
more high powered loads from a timer or
environmental controller. Usually the electrical outlet for your timer or controller can only service a single 1000 watt fixture without tripping the circuit
breaker. By utilizing other outlets (on separate circuit breakers) more fixtures can be added and still be controlled by your timer. These Power Expanders
have ready to go outlets (120 volt), a 6 foot trigger cord. The PWX-D20 (not shown) is similar to the PWX-1 except it delays 20 seconds before turning
on. Inserting a delay between turning on heavy electrical loads helps avoid circuit breaker popping and other electrical problems.
PWX POWER EXPANDERS
703620
Timer not
included
PWX-240-6 Power Expander lets you control up to six 1000 watt 240 volt lighting systems. Comes Pre-wired w/10 gauge 6’ power cable and
a 6’ trigger cord with a 120 volt plug. The power cable connects to a 240V 30A service. The trigger cord can be connected to any 24 hour timer/
controller. The Trigger cord turns all six outlets on at once.
The PWX240S (not shown) is similar to the PWX240-6 except that it sequences the outlet pairs on. The first outlet pair turns on immediately &
the final 2 outlet pairs turn on 20 seconds apart. This helps avoid circuit breakers popping.
NEW!
PWX POWER EXPANDERS
703617
Timer not included
Code# Description
703617 PWX-240-4 Power Expander
703618 PWX-240-U Power Expander
MSRP
$229.95
$249.95
PWX-240-4 Power Expander lets you control up to four 1000 watt 240 volt lighting systems. Comes
pre-wired with 12 gauge 6’ power cable and a 6’ trigger cord with a 120V plug. The power cable connects
to a 240V 20A service. The trigger cord can be connected to any 24 hour timer/controller. The trigger
cord turns four outlets on at once.
703618
Timer not included
LP-120S AND LP-240S LAMP PRO TIMERS
703630
703625
PWX-240-U Power Expander lets you control up to four 1000 watt 240 volt lighting systems. Comes
Pre-wired with a 10 gauge 6’ power cable and a 6’ trigger cord with 120V plug. The power cable connects
to a 240V 30A service. The trigger cord can be connected to any 24 hour timer/controller. The trigger
cord turns on all four 240V outlets at once. PLUS: two 120 volt utility outlets that are always on with
an added 10 amps each. The trigger cord has no effect on the 120V outlets.
Code# Description
703625 LP-120S Lamp Pro Timer (120 Volt 15 Amp)
703630 LP-240S Lamp Pro Timer (240 Volt 30 Amp)
MSRP
$279.95
$319.95
These easy to use timers have a single select knob that clicks to any of 16 time settings. Settings include an accelerated 18 hour day
cycle running ON 6 hours / OFF 12 hours. Thirteen normal 24 hour day settings cover ON 8 / OFF 16 to ON 20 / OFF 4 in one hour
increments. Continuously ON and OFF settings are also included. The Lamp Pro sequences two outlets on, 20 seconds later the next
two, and 20 seconds later the final two. This reduces electrical problems. Turn off has a 5 second delay. The LP-120S (120 volt 15
amp) uses standard 120 volt type outlets and power cord plug. The LP-240S (240 volt 30 amp) has 240 volt outlets and an 6 foot
power cord with unterminated wires. It can control up to six 1000 watt fixtures.
GAS PRO CO2 GENERATOR & CO2 400 CONTROLLER
Code#
703635
703640
703645
703650
703655
703660
703665
703670
703632
Description
Gas Pro 6 Burner NG CO2 Generator
Gas Pro 6 Burner LP CO2 Generator
Gas Pro 12 Burner NG CO2 Generator
Gas Pro 12 Burner LP CO2 Generator
Gas Pro 6 NG Generator With CO2 400 Controller
Gas Pro 6 LP Generator With CO2 400 Controller
Gas Pro 12 NG Generator W/ CO2 400 Controller
Gas Pro 12 LP Generator With CO2 400 Controller
CO2 400 Controller (Special Order)
MSRP
$831.00
$831.00
$998.95
$998.95
$1,187.50
$1,187.50
$1,363.00
$1,363.00
$499.95
CO2 can be added by burning propane or natural
gas - cheaper and easier to obtain than bottled
CO2. The Gas Pro uses faster, more reliable, more
efficient, electronic spark ignition. When it is
turned on, spark and pilot gas start. When the pilot
is lit, spark stops and main gas turns on and is lit
by pilot. When the Gas Pro turns off, all gas turns
off. Spark is better than standing/continuous pilot.
Spark is faster and more reliable than a glow plug,
spark ignites immediately. The Propane model
includes a regulator for connection to a propane tank. A gas hose (20 ft.) is included with all models. Strong 18 gauge steel enclosure - powder coated for
heat and rust resistance. Heat exchanger allows forced air cooling if desired. Plug the 120 volt power supply (included) into a controller or timer. Alternatively,
the Gas Pro allows easy connection of a CO2 400 controller. Just plug CO2 400’s 10 ft. cable into the connector on the side of Gas Pro. Extension cable available.
No separate power supply needed - it draws power from the Gas Pro. Includes easy to use display and controls to view and adjust ppm levels.
126
SOLATEL CONTROLLERS
ENVIRONMENTAL CONTROLLERS
HARVEST-MASTER® PRODUCTS
Harvest-Master® products are automated hydroponic grow room climate controllers. Harvest-Master® controller devices continuously control your crop condition and growth time. The controllers come
ready to operate with factory preset settings. No Hassles! Scientists have researched and developed the optimum settings so that you obtain a “Great Harvest” for a wide variety of herbs, flowers and fruiting
crops. Just set the grow cycle you want: Vegetative, Fast Flowering or Full Flowering for a perfect optimum growth climate day and night. Settings can be changed as required, but we advise that factory
settings be used initially.
Self Learning Capability & Automatic Room Calibration
• As soon as Harvest-Master® is switched on, it begins learning how your room performs and reacts. Hour by hour, learning about temperature and humidity changes continuously, all day every day.
• This information enables Harvest-Master® to understand, calculate and predict how your devices will best balance temp, humidity and CO2 for the most gentle organic growing conditions.
• Harvest-Master® always makes the optimum decisions to ensure healthy vigorous crops.
Code#
703300
703305
703310
Description
Harvest-Master® Climate Controller
Harvest-Master® Climate Pro Controller
Harvest-Master® Climate Pro Plus Controller
MSRP
$899.00
$1,599.00
$2,099.00
HARVEST-MASTER® CLIMATE CONTROLLERS
703300
Controls night and day length, temperature and humidity control, plus control up to 8 devices (or 7 and
a cycle timer), for a balanced climate. All models come as a complete kit. The kit includes: controller,
sensors, remote relay switches. Sensors are high accuracy types, for temperature, humidity and CO2.
3 remote relay switches are included for lights and heaters to put on different electrical circuits. The
“Pro” model is the same as the Climate model plus a CO2 sensor and a 4th relay switch. The “Pro Plus”
model is the same as the Climate Plus model plus 8 additional inputs & outputs, to control advanced
functions including automation or alarms which can drive the optional “Text Message” (product no.
703335) option.
Code# Description
703320 Harvest-Master® CO2 EASi Unit
703325 Harvest-Master® CO2 EASi Kool Kit
703310
HARVEST-MASTER® CO2 EASI UNITS
MSRP
$649.00
$109.90
CO2 EASi is an intelligent control of CO2
& at the same time, an Intelligent Temp.
controller when the COOL KIT is attached for additional automatic control of cooling units and or fans. As soon as CO2 EASi is switched ON, it learns
how CO2 enrichment works in your room, including whether you use bottle or burner. Continuous learning and adjustment all day, every day. CO2 EASi
will understand, calculate and predict enrichment operations for optimum growth.
Consumption: Automatic calculation and display of CO2 consumption rate, with predicted bottle life remaining.
Efficiency Monitoring: Shows percentage of optimum CO2 enrichment time achieved. Automatic and continuous evaluation of cooling and exhaust
systems efficiency. Identifies where improvements can be made for more growth, increased yield, reduced CO2 use and lower power costs.
Code# Description
703350 Harvest-Master® Relay - 120 volt
703355 Harvest-Master® Relay - 240 volt
HARVEST-MASTER® RELAYS
MSRP
$79.90
$159.00
703355
Relay switches for you to plug and run: Lights, Fans, Heater or any other timed device. Each relay is rated to switch 15-amps. 120 Volt AC or 240 Volt
AC: USA.
240v, 2-pole relay switches available.
Heavy Duty 3 phase 32-amp per phase type available.
Relays can be daisy chained with “Y” connectors to permit up to 6 relay switches to be switched ON by a single Harvest-Master® output signal (for up
to 6 light arrays for example). NOTE: A maximum of 7 relay switches per controller output.
703350
Code# Description
703335 Harvest-Master® Text Me Modem For Pro Plus Only
MSRP
$867.00
HARVEST-MASTER® TEXT ME MODEM
The modem gives you instant text message updates, direct to your phone. Send ‘status’, to get an update from your Harvest-Master® controller, from
anywhere! Turn the extra 8 outputs ON or OFF by text message. Get text messages for an alarm! Overheating, low water/fluid levels, or INTRUDERS!
(door/window switches, motion detectors).
Code# Description
703340 Harvest-Master® CO2 Upgrade for Climate to a Pro
MSRP
$649.00
HARVEST-MASTER® CO2 UPGRADE
CO2 sensor upgrades the controller to monitoring and accurate (to 100ppm) dispensing of CO2. Harvest-Master® knows when CO2 is operating and
changes automatically to suit the high CO2 environment (higher humidity, no fans etc). Continuously relearns the “delivery time” required to get
perfect ppm levels without overruns! Harvest-Master® Automatically disables CO2 operations if the system runs out of CO2 (allows fans to be used
and holds humidity to lower levels)!
HARVEST-MASTER
127
FANS/BLOWERS/DUCTING
ECOPLUS® SUPREME INLINE FANS
Code#
736600
736605
736610
736675
736680
5 YEAR
WARRANTY
Description
EcoPlus® Supreme 4” Inline Fan
EcoPlus® Supreme 6” Inline Fan
EcoPlus® Supreme 8” Inline Fan
EcoPlus® Supreme 10” Inline Fan
EcoPlus® Supreme 12” Inline Fan
• The original, proven, high performance
EcoPlus® fans.
• Very powerful and efficient motors
• Pre-wired with 120 volt power cord
ECOPLUS® CLASSIC INLINE FANS
NEW!
Code#
736430
736435
736440
736445
736450
5 YEAR
WARRANTY
•
•
•
•
CFM
170
440
740
780
1060
MSRP
$135.95
$173.95
$220.95
$270.95
$330.95
• Durable steel housing with blue powder coated
finish
• Wall or ceiling mounting brackets attached for
easy installation
Description
EcoPlus® Classic 4” Inline Fan
EcoPlus® Classic 6” Inline Fan
EcoPlus® Classic 8” Inline Fan
EcoPlus® Classic 10” Inline Fan
EcoPlus® Classic 12” Inline Fan
CFM
160
340
590
730
980
MSRP
$109.95
$144.95
$184.95
$239.95
$279.95
Very powerful and efficient motors
Durable steel housing with black powder coated finish
Wall or ceiling mounting brackets attached for easy installation
Pre-wired with 120 volt power cord
CAN-FAN® INLINE FANS
Can-Fan® bring its innovation to market and sets a new standard for performance. The outstanding
performance of our fans set them apart from the competition. Each fan comes pre-wired with an
8’ - 120 volt power cord. 5 year warranty.
Code#
736780
736785
736790
736795
736800
736805
736810
736815
Description
Can-Fan® 4”
Can-Fan® 4” High Output
Can-Fan® 6”
Can-Fan® 6” High Output
Can-Fan® 8”
Can-Fan® 8” High Output
Can-Fan® 10” High Output
Can-Fan® 12” High Output
CAN-FAN® MAX-FAN™
NEW SIZES!
Max CFM
142
178
270
440
493
737
781
971
Max RPM
3200
3260
3240
3246
3215
3310
3290
3365
Code#
736825
736830
736835
736840
Max Watts Diameter
61
11.26”
70
11.26”
73
12.3”
136
15.1”
125
15.2”
253
15.2”
251
15.2”
331
17.5”
Description
8” Max-Fan™
10” Max-Fan™
12” Max-Fan™
14” Max-Fan™
Inlet/Outlet
3.94”
3.94”
5.9”
5.9”
7.87”
7.87”
9.84”
12.0”
CFM
675
1023
1709
1823
MSRP
$175.95
$186.95
$199.95
$226.95
$264.95
$284.95
$306.95
$433.95
MSRP
$286.95
$433.95
$526.95
$764.95
Can-Fan® bring its innovation to market and sets a new standard for performance. The Max-Fan™ is
more powerful and efficient fan that takes less energy to run. Come pre-wired with an 8’ - 120 volt
power cord. 5 year warranty.
CAN-FAN® BACKDRAFT DAMPERS
Code#
736845
736850
736855
736860
736865
736870
Description
4” Backdraft Damper
6” Backdraft Damper
8” Backdraft Damper
10” Backdraft Damper
12” Backdraft Damper
14” Backdraft Damper
These newly developed back draft dampers are manufactured with quality components and
precision engineering. The back draft damper is used to prevent air from flowing through the fan (powered off) allowing contaminated air to escape the room.
128
INLINE FANS
MSRP
$24.95/ea
$28.95/ea
$37.95/ea
$46.95/ea
$59.95/ea
$88.95/ea
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement