PT398-35121 - TRDparts4u

PT398-35121 - TRDparts4u
TOYOTA
TACOMA
2012 -
TVIP V5
Preparation
RS3200 PLUS
Part Number: PT398-35121
Conflicts
Note: Must not be installed in Vehicles with Factory Alarm
System and 2013- Vehicles with (4WD Double Cab 6MT
and Off-Road Package).
Kit Contents
Item #
1
2
3
4
5
6
7
8
Quantity Reqd.
1
1
1
1
2
2
1
1
Description
Wire Harness
Security ECU
GBS ECU
Status Monitor/Microphone
Warning Labels (English)
Warning Labels (Spanish)
Owner’s Manual
Warranty Card
Quantity Reqd.
1
1
1
4
15
15
Quantity Reqd.
1
1
Safety Glasses
Safety Gloves
Vehicle Protection
Optional
Blankets, Part Boxes
Special Tools
Notes
CAD-E IADS P/N
ALL02-016-01
Grabber Tool (Flexible Pick- (CAD-E IADS P/N
up Tool)
COR02-016-01 (PPO))
ECU Pin Remover Tool
Toyota SST: 1276565-1
Description
ECU Mounting Bracket
Bolt
Large Foam Tape Strip (2 pcs.)
Small Foam Tape Strips
Medium Wire Ties
Large Wire Ties
Installation Tools
Notes
Screwdriver
#2 Phillips, Flat Blade
Jeweler’s
10 mm, extension
48 in•lbf (5.4 N•m)
e.g. Panel Pry Tool #1
Socket
Torque Wrench
Nylon Panel Removal Tool
Toyota SST # 00002-06001-1
Cloth
Side Cutter
Tape
Cleaner
Glass Cleaner
Description
Lint-free Cloth
replacement foot rest
(PN: 58190-04021)
Note: Tacoma with Remote keyless Entry.
Recommended Sequence of Application
Accessory
Audio
Trailer Wire Harness
V5
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
1
2
3
4
5
Issue: C
Quantity Reqd.
3
5
2
4
4
07/25/12
Masking, Electrical, Clear
VDC Approved Cleaner
Household Glass Cleaner
Legend
General Applicability
Item #
1
2
3
Lint-free
Special Chemicals
Additional Items Required For Installation
Item #
1
2
Notes
Striker Tool (PPO Only)
Hardware Bag Contents
Item #
1
2
3
4
5
6
Recommended Tools
Personal & Vehicle
Protection
Description
Clips – lower dash cover
Clips – audio panel
Clips – glove box inner cover
Clips – center cluster panel
Clips – small cover lower IP
Page 1 of 24
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
SAFETY TORQUE: This mark indicates that torque is
related to safety.
Wire Harness Outline*
B
W
P
A
E
U
Q
Z
H
I
G
V
L
F
N
D
X
R
Y
C
K
J
14P White
B
14P White
C
10P White
D
10P White
E
40P White
(for V5 Security ECU)
F
8P White
(for GBS ECU)
G
2P White
H
10P Gray
I
10P Gray
J
11P Gray
K
11P Gray
L
8P White
M
8P White
N
18P White
O
18P White
P
4P White
Q
13P Black
R
4P Black
(for Status Monitor)
S
13P Black
T
18P White
U
18P White
V
GBS ECU
W
V5 Security ECU
X
Relay
Y
Status Monitor
Z
Diode
TVIP V5
A
2012 –
Page 2 of 22
T
M
O
S
Description
TOYOTA TACOMA TVIP
PREPARATION
RS3200 PLUS
Issue C : 07/25/12
Tacoma
TOYOTA
TACOMA
2012 -
TVIP V5
Procedure
RS3200 PLUS
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
 Safety (eye protection, rechecking torque procedure, etc.).
 Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
 Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
1. Vehicle Disassembly.
10mm Socket
Negative Battery
Cable
(a) Place Automatic Vehicles in low gear with
the parking brake set.
(b) Remove the negative battery cable.
(Fig. 1-1)
(1) Protect the fender before starting.
(2) Note the Cable Position as it will be
reinstalled in the same position.
Fig. 1-1
CAUTION: Do not touch the positive terminal.
Nylon Panel Removal Tool
Nut
Foot Rest
(c) Remove the driver side foot rest, and the
driver side step cover. (Fig. 1-2)
(1) Cover the floor and seats before starting.
Cowl Cover
NOTE: discard the foot rest. A replacement foot
rest (PN: 58190-04021) must be used.
Step Cover
(d) Remove driver side cowl cover. (Fig. 1-2)
Fig. 1-2
(1) Remove the nut securing the cowl cover.
Nylon Panel Removal Tool,
10 mm Socket
M/T MODELS
Lower Dash
Cover
Cover
FOR M/T VEHICLE MODELS ONLY.
(Steps e-g)
(e) Remove the small cover from the lower dash
cover’s right side. (Fig. 1-3)
(f) Remove the hood release cable. (Fig. 1-3)
(g) Remove the lower dash cover. (Fig. 1-3)
Hood Release
Lever
Fig. 1-3
Issue: C
Bolt
Bolt
07/25/12
Page 3 of 22
(1) Open the screw cover of the lower dash cover.
(2) Remove the two bolts securing the cover.
TOYOTA
TACOMA
2012 -
TVIP V5
Procedure
RS3200 PLUS
Nylon Panel Removal Tool,
10mm Socket
A/T MODELS
Cover
Lower Dash
Cover
FOR A/T VEHICLE MODELS ONLY.
(Steps h-j)
(h) Remove the small cover from the lower dash
cover’s right side. (Fig. 1-4)
(i) Remove the hood release cable. (Fig. 1-4)
Hood Release
Lever
Fig. 1-4
(j) Remove the lower dash cover. (Fig. 1-4)
(1) Open the screw cover of the lower dash cover.
(2) Remove the two bolts securing the cover.
Bolt
Bolt
Bolt (x3)
10mm Socket
(k) Remove the metal substructure. (Fig. 1-5)
(1) Remove 3 bolts.
CAUTION: Sharp metal edges.
Fig. 1-5
Metal Substructure
Phillips Screwdriver
Screw
Screw
(l) Remove the two screws securing the lower
steering column cover behind the steering
wheel. (Fig. 1-6)
(1) Insert the key into the ignition switch and turn
it to ON to unlock the steering wheel.
(2) Turn the steering wheel left and right to gain
access to the screws.
Steering Column Cover
Fig. 1-6
(m) Remove the lower steering column cover.
(Fig. 1-7)
Fig. 1-7
Issue: C
Steering Column Cover
07/25/12
Page 4 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Nylon Panel Removal Tool
Center Cluster Panel
(n) Attach the low adhesion masking tape on the
center cluster panel, as shown. (Fig. 1-8)
CAUTION: Only apply tape on the Center
Cluster Panel surface.
Masking Tape
(o) Using the Nylon Panel Removal Tool,
remove the center cluster panel. (Fig. 1-8)
(1) Loosen the four clips when removing the
panel.
(2) Disconnect all connectors from the panel.
Fig. 1-8
10mm Socket
Audio Unit
(p) Remove the audio unit. (Fig. 1-9)
(1) Remove 4 bolts.
(2) Disconnect all connectors from the audio unit.
NOTE: Prior to removing the radio assembly
from the dash, cover the radio mounting tabs
with a cloth to prevent damage to the vehicle.
Fig. 1-9 Bolts (x4)
Audio Unit
Mounting Tabs
Cloth
VEHICLES WITHOUT SEAT HEATER
Nylon Panel Removal Tool
(q) Remove the knockout cover. (Fig. 1-10)
Knockout Cover
Fig. 1-10
VEHICLES WITH SEAT HEATER
Nylon Panel Removal Tool
(r) Remove the knockout cover. (Fig. 1-11)
Knockout Cover
Fig. 1-11
Issue: C
07/25/12
Page 5 of 22
TOYOTA
TACOMA
2012 -
TVIP V5
Procedure
RS3200 PLUS
Nylon Panel Removal Tool
(s) Remove the passenger side step cover.
(Fig. 1-12)
Nut
(1) Cover the floor and seats before starting.
(t) Remove the passenger side cowl cover.
(Fig. 1-12)
Cowl Cover
Fig. 1-12
(1) Remove 1 nut.
Step Cover
(u) Remove the glove box. (Fig. 1-13)
(1) Remove the dampener from the glove box.
Glove Box
Dampener
Fig. 1-13
(v) Remove the glove box inner cover.
(Fig. 1-14)
10mm Socket
(1) Remove 1 bolt.
Bolt
Inner Cover
Fig. 1-14
Ignition Switch
Vehicle's 8P
(White)
Steering Wheel
2. V5 Harness Installation.
(From Center Cluster Area to Driver Side
Cowl Area)
(a) Locate and disconnect the white 8P
connector from the ignition switch in the
steering column area. (Fig. 2-1)
Fig. 2-1
Issue: C
07/25/12
Page 6 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Side Cutter
Ignition Switch
Large Wire Tie
8P (White)
(c) Secure the white 8P connectors to the
vehicle harness with 1 large wire tie.
(Fig. 2-2)
V5
Harness
(d) Secure the V5 harness to the vehicle harness
with 2 large wire ties. (Fig. 2-2)
large Wire Ties (x2)
Fig. 2-2
13P (Black)
(b) Plug in the V5 harness' white 8P connectors
between the ignition switch and the vehicle
harness' white 8P connector.
(e) Locate and disconnect the black 13P
connector, and two white 18P connectors
from the driver side J/B. (Fig. 2-3)
18P (White)
J/B
18P (White)
(f) Plug in the V5 harness’ black 13P
connectors between the driver’s side J/B and
the vehicle harness’ black 13P connector.
Plug in the V5 harness’ 18P connectors
between the driver’s side J/B and the vehicle
harness’ white 18P connector. (Fig. 2-4)
Fig. 2-3
Side Cutter
18P
18P
13P (Black)
(1) Verify the connectors are plugged in securely.
(g) Plug in the V5 harness' other white 18P
connectors between the driver's side J/B and
the vehicle harness' white 18P connector.
(1) Verify the connectors are plugged in securely.
Fig. 2-4
medium Wire Ties (x5)
V5
Harness
(h) Secure the 13P(black) connectors, 2 18P
connectors and V5 Harness to the vehicle
harness with 5 medium Wire Ties, in front
of the driver side J/B. (Fig. 2-4)
(1) Align the V5 harness’ branch point to the end
of the corrugated tube of the vehicle harness.
V5 Harness
2P (White)
10P (Gray)
(i) Route the V5 harness' white wire terminal,
white 2P connector and Gray 10P
connectors behind the brace down toward
the driver side cowl area as shown.(Fig. 2-5)
Wire Terminal
Fig. 2-5 (White)
Issue: C
07/25/12
Page 7 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Vehicle’s
10P (Gray)
Tape
Vehicle’s
12P (White)
Fig. 2-6
12P (White)
2P (White)
(1) Verify the connectors are plugged in securely.
10P (Gray)
WHITE Wire
Terminal
Fig. 2-7
V5 Harness
Tape
(k) Locate the hole in the driver side cowl area,
then pull out the vehicle harness’ Gray 10P
connector and disconnect it. (Fig. 2-6)
(l) Plug the V5 harness' Gray 10P connectors
between the vehicle harness' Gray 10P
connectors, then insert the Gray 10P
connectors into the hole in the driver side
cowl area. (Fig. 2-7)
V5 Harness
Tape
(j) Locate the vehicle’s white 12P connector in
the driver side cowl area, and remove the
electrical tape from the vehicle’s white 12P
connector, then disconnect it for clearance.
(Fig. 2-6)
Combination
Connector
Connector
Block
(m) Reconnect the vehicle harness’ white 12P
connector and secure it to the vehicle
harness using electrical tape. (Fig. 2-7)
(n) Locate and disconnect the combination
connector from the connector block in the
driver side cowl area. (Fig. 2-8)
2P (White)
WHITE Wire
Terminal
Fig. 2-8
Jeweler’s Screwdriver
8P (White)
Combination
Connector
(o) Using a small jeweler's screwdriver, release
and pull out the white 8P connector from the
combination connector. (Fig. 2-9)
(1) Turn the connectors so the pins face you.
Fig. 2-9
Issue: C
07/25/12
Page 8 of 22
TOYOTA
TACOMA
2012 -
TVIP V5
Procedure
RS3200 PLUS
Jeweler's Screwdriver, ECU Pin Removal Tool
8P (White)
WIRE SIDE VIEW
Retainer
Combination
Connector
Vehicle Harness'
WHITE Wire
Terminal
Fig. 2-10
Retainer
WIRE SIDE VIEW
V5 Harness’
WHITE Wire
Terminal
Fig. 2-11
Combination
Connector
(p) Using a small jeweler's screwdriver, lift up
the terminal retainer on the back of the 8P
connector. Locate the WHITE wire in the 8P
connector. Using the ECU pin remover tool
or a small jeweler’s screwdriver, release and
pull out the terminal for the WHITE wire.
(Fig. 2-10)
(1) Do not pull out the retainer.
(2) Turn the connector so the wires face you and
the retainer is on top.
8P (White)
(q) Insert the terminal at the end of the V5
harness' WHITE wire into the seventh space
from the left of the 8P connector, then close
the retainer. Refit the white 8P connector to
the combination connector. (Fig. 2-11)
(1) Turn the connector so the wires face you and
the retainer is on top.
(2) Verify the correct opening is chosen.
(3) Verify the terminal is inserted and seated
properly. The terminal should not come out
when pulled lightly from the back. If the
terminal comes off, then push it in again.
Retainer
(r) Disconnect the empty 2P female connector
plugged into the V5 harness. Using a small
jeweler's screwdriver, lift up the terminal
retainer on the back of the empty 2P
connector. (Fig. 2-12)
Jeweler's Screwdriver
V5 Harness
(1) Do not pull out the retainer.
2P (Female)
Fig. 2-12
2P (Female)
Retainer
Retainer
Vehicle Harness'
WHITE Wire
Terminal
Fig. 2-13
Issue: C
07/25/12
2P (Female)
(s) Insert the terminal at the end of the vehicle
harness' WHITE wire into the right side
opening of the empty 2P connector as
shown, then close the retainer. (Fig. 2-13)
(1) Turn the connector so the wires face you and
the tab is on top.
(2) Verify the correct opening is chosen.
(3) Verify the terminal is inserted and seated
properly. The terminal should not come out
when pulled lightly from the back. If the
terminal comes off, then push it in again.
WHITE
WIRE SIDE VIEW
Page 9 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Combination
Connector
V5 Harness
2P (White)
(t) Plug in the V5 harness' white 2P male
connector to the white 2P female connector,
and reconnect the combination connector.
(Fig. 2-14)
(1) Verify the connectors are plugged in securely.
(u) Wrap the Gray 10P connectors in one small
foam tape strip. (Fig. 2-14)
10P (Gray)
Small Foam
Tape Strip
Fig. 2-14
Combination
Connector
2P (White)
Side Cutter
V5 Harness
Medium
Wire Ties
(x2)
10P (Gray)
(v) Secure the Gray 10P connectors to the
vehicle harness using one medium wire tie.
(Fig. 2-15)
(w) Bundle up the excess V5 harness, then
using one medium wire tie, secure the
2P connectors and V5 harness as shown.
(Fig. 2-15)
Fig. 2-15
M/T MODELS
Small Foam
Tape Strips
(2x)
3. V5 Harness Installation.
(From Center Cluster Area to Passenger Side
Cowl Area)
FOR M/T VEHICLE MODELS ONLY.
(Step a)
Vehicle's
Brace
Brake Shaft
Fig. 3-1
(a) Attach two small foam tape strips to the
vehicle's brace as shown. (Fig. 3-1)
(1) Do not attach anything to the brake shaft.
A/T MODELS
Vehicle's
Brace
FOR A/T VEHICLE MODELS ONLY.
(Step b)
(b) Attach one small foam tape strip to the
vehicle's brace as shown. (Fig. 3-2)
Small Foam
Tape Strip
Fig. 3-2
Issue: C
07/25/12
Page 10 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
(c) Route the V5 harness toward the center
cluster area using the grabber tool.
(Fig. 3-3)
Grabber Tool
(1) Insert the grabber tool from the center cluster
area and push it toward the driver side upper
brake shaft area.
(2) Catch the V5 harness 10P connectors using the
grabber tool, then pull it back toward the
center cluster area.
Grabber Tool
V5 Harness
Brake Shaft
Fig. 3-3
(d) Secure the V5 harness’ relay to the vehicle
brace with one large wire tie. (Fig. 3-4)
Side Cutter Tool
Large Wire
Tie
V5 Harness
Relay
Fig. 3-4
Side Cutter
Large Wire Ties (x3)
(e) Route the V5 harness toward the passenger
side glove box area. (Fig. 3-5)
(f) Secure the V5 harness to the vehicle harness
with 3 large wire ties. (Fig. 3-5)
Fig. 3-5
VEHICLES WITHOUT SEAT HEATER
(g) Route the V5 harness' 4P black connector
downward and out of the open knockout
location. (Fig. 3-6)
Fig. 3-6
Issue: C
07/25/12
Page 11 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
(h) Connect the V5 black 4P connector to the
Status monitor. (Fig. 3-7)
(1) Verify the connectors are plugged in securely.
(i) Push the Status Monitor into the open knock
out location until it snaps in place. (Fig. 3-7)
Fig. 3-7
(j) Pull the excess V5 harness back up into the
center console as shown. (Fig. 3-8)
Fig. 3-8
(k) Secure the V5 Harness to the Vehicle
Harness using 1 large wire tie. (Fig. 3-9)
Side Cutter
Fig. 3-9
Large Wire Tie
VEHICLES WITH SEAT HEATER
(l) Route the V5 harness’ 4P black connector
downward and out of the open knockout
location. (Fig. 3-10)
Fig. 3-10
Issue: C
07/25/12
Page 12 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
(m) Connect the V5 black 4P connector to the
Status monitor. (Fig. 3-11)
(1) Verify the connectors are plugged in securely.
(n) Push the Status Monitor into the open knock
until it snaps in place. (Fig. 3-11)
Fig. 3-11
(o) Pull the excess V5 harness back up into the
center console as shown. (Fig. 3-12)
Fig. 3-12
(p) Secure the V5 Harness to the Vehicle
Harness using 1 large wire tie. (Fig. 3-13)
Side Cutter
Fig. 3-13
Large Wire Tie
(q) Plug in the V5 14P male connector to the
vehicle 14P female connector. (Fig. 3-14)
(1) Verify the connectors are plugged in securely.
Fig. 3-14
Issue: C
07/25/12
Page 13 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
(r) Bundle the excess portion of the vehicle
harness, then secure the V5 harness and
vehicle harness with 1 large Wire Tie.
(Fig. 3-15)
V5 Harness
Side Cutter
Large Wire Tie
14P (White)
Fig. 3-15
Side Cutter
Large Wire Tie
Reinforcement
Fixation
(s) Secure the V5 harness to the vehicle harness
with 1 medium Wire Tie. (Fig. 3-16)
(t) Route the V5 harness behind the
reinforcement fixation securing it with
1 large Wire Tie. (Fig. 3-16)
V5 Harness
Fig. 3-16
Medium Wire Tie
Tape
(u) Locate the vehicle harness' white 4P female
connector and remove the tape securing the
4P connector. (Fig. 3-17)
Vehicle's 4P
(White)
4P (White)
V5 Harness
Fig. 3-17
Side Cutter
Medium Wire Ties (x3)
4P (White)
V5 Harness
(v) Plug in the V5 harness' white 4P male
connector to the vehicle harness' white 4P
female connector. Secure the V5 harness
and white 4P connectors to the vehicle
harness with three medium wire ties.
(Fig. 3-18)
(1) Verify the connectors are plugged in securely.
Fig. 3-18
Issue: C
07/25/12
Page 14 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Side Cutter, Flat
blade Jewelers
Screwdriver
V5 Harness
Vehicle's
Clip
(w) Route and secure the V5 harness to the
vehicle harness with two medium wire ties
and the vehicle's wire clip. (Fig. 3-19)
8P (White)
40P (White)
Fig. 3-19
Medium Wire Ties (x2)
(x) Locate and disconnect the gray 11P
connector to the connector block on the
passenger side cowl area. (Fig. 3-20)
Vehicle’s
11P (Gray)
Connector
Box
Fig. 3-20
(y) Locate the vehicle’s outer white 10P
connector in the passenger side cowl area,
and remove the tape from the vehicle’s
white 10P connector, then disconnect it for
clearance. (Fig. 3-21)
Vehicle’s Inner
10P (White)
Tape
Vehicle Harness’
Outer 10P (White)
Fig. 3-21
Issue: C
07/25/12
Connector
Box
(z) Locate the hole in the passenger side cowl
area, then pull out the vehicle harness’ inner
white 10P connector and disconnect it.
(Fig. 3-21)
Page 15 of 22
TOYOTA
TACOMA
2012 -
Procedure
TVIP V5
RS3200 PLUS
Vehicle’s
10P (White)
V5 Harness
Connector
Box
(aa) Plug in the V5 10P connectors between the
vehicle’s inner 10P connectors. (Fig. 3-22)
(1) Both inner and outer white 10P connectors fit
the V5 harness. Use the inner white connector.
V5 Harness’
10P (White)
(bb) Plug in the V5 gray 11P connectors between
the vehicle’s gray 11P connector and the
connector block. (Fig. 3-22)
Small
Foam
Tape
11P (Gray)
Fig. 3-22
Side Cutter
(cc) Place the inner white 10P connectors in the
concave spot of the cowl area. (Fig. 3-22)
V5 Harness
10P (White)
Medium Wire
Ties (x2)
11P (White)
Large Wire Tie
(dd) Reconnect the vehicle outer 10P connector
and secure to the vehicle harness using 1
small Foam Tape. (Fig. 3-22)
(ee) Reconnect the vehicle’s outer white 10P
connector and secure it to the vehicle
harness using the electrical tape. (Fig. 3-23)
(ff) Secure the V5 harness to the vehicle harness
with two medium wire ties. (Fig. 3-23)
Fig. 3-23
V5 Security ECU
(gg) Secure the white 11P connectors to the
vehicle harness with one large wire tie.
(Fig. 3-23)
4. V5 Security ECU and V5 GBS ECU
Installation.
ECU Mounting
Bracket
(a) Insert the V5 security ECU mounting
bracket tab into the indicated bracket slot on
the V5 security ECU. (Fig. 4-1)
Fig. 4-1
(1) Insert the mounting bracket into the correct
slot; you have only one chance to install it
properly.
Flat blade Jewelers Screwdriver
V5 GBS ECU
CAUTION: Due to a tight fit between the V5
ECU and bracket, it may be necessary to support
the bracket on a flat surface corner and press the
ECU onto the bracket.
(b) Turn the adjustment screw on the V5 GBS
ECU to the "8" position. (Fig. 4-2)
Fig. 4-2
Issue: C
07/25/12
Page 16 of 22
TOYOTA
TACOMA
2012 -
Procedure
V5 GBS ECU
Large Foam
Tape Strips (x2)
(c) Apply two large foam tape strips to the V5
GBS ECU as shown. (Fig. 4-3)
(d) Insert the V5 GBS ECU mounting bracket
tab into the indicated bracket slot on the V5
GBS ECU. (Fig. 4-3)
V5 GBS ECU
(1) Insert the mounting bracket into the correct
slot; you have only one chance to install it
properly.
ECU Mounting
Bracket
V5 Security ECU
Fig. 4-3
TVIP V5
RS3200 PLUS
Vehicle Brace
Small Foam
Tape
V5 Harness
(e) Connect the V5 harness’ white 40P
connector and white 8P connector to the V5
security ECU and V5 GBS ECU. (Fig. 4-4)
(1) Verify the connectors are plugged in securely.
V5 GBS ECU
(f) Apply one small foam tape strip to the
vehicle brace as shown. (Fig. 4-4)
8P (White)
Fig. 4-4
40P (White)
V5 Security ECU
10mm Socket
V5 Security
ECU
V5 GBS ECU
(g) Using the supplied bolt, secure the V5
security ECU and V5 GBS ECU to the
reinforcement fixation. (Fig. 4-5)
V5 Harness
Reinforcement
Bolt (Supplied)
Fig. 4-5
Side Cutter
V5 Security
ECU
V5 GBS ECU
(h) Secure the V5 ECU harness and the GBS
ECU portion of the V5 harness to the
vehicle harness with one large wire tie.
(Fig. 4-6)
V5 Harness
Wire Tie
Fig. 4-6
Issue: C
07/25/12
Page 17 of 22
TOYOTA
TACOMA
2012 -
TVIP V5
Procedure
RS3200 PLUS
5. Warning Label Installation.
●
●
For US Vehicles use the English Labels and Tag, and
discard the Spanish Tags and Labels.
For Mexico Vehicles use the Spanish Labels and Tag,
and discard the English Tags and Labels.
(a) Use Household Glass Cleaner to clean the
inside of the Front Door Window.
Clear Tape
Etching
Etching
Molding
(b) Use a piece of Clear Tape to lift the Label
from its protective backing.
CAUTION: Do not touch the adhesive surface.
(c) Attach the Label as shown. (Fig. 5-1)
Molding
Fig. 5-1
NOTE: Make sure to Align according to Etching
or Other Label. (Fig. 5-1)
REPEAT: steps a–c with the other Window.
6. Completing the Installation.
(a) Complete the reassembly of the vehicle.
(1) Prior to replacing the radio assembly into the
dash, cover the radio mounting tabs with a
cloth to prevent damage to the vehicle.
(2) Reconnect any disconnected connectors.
(3) Verify the panels fit together properly with no
uneven gaps between them.
NOTE: When installing the Foot Rest use a
Replacement Foot Rest (PN: 58190-04021)
Torque Wrench
Negative Battery
Cable
(b) Clean up and remove any trash.
(c) Reconnect the vehicle's negative battery
cable. (Fig. 6-1)
(1) Position the negative battery cable at the
original factory position.
(2) Tighten the nut to 48 in•lbf (5.4 N•m).
Battery
(d) Place the owner's manual and warranty card
left in their protective bags in the glove box.
Fig. 6-1
Issue: C
CAUTION: Do not touch the positive terminal.
07/25/12
Page 18 of 22
TOYOTA
TACOMA
2012–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Accessory Function Checks
Perform
Look For
1
Press and release the remote control’s lock
button to start the system’s arming process.
The turn signal lights flash once.
All doors lock.
The security LED lights up.
2
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
3
Press and release the remote control’s
unlock button to disarm the system.
The turn signal lights flash twice.
The driver’s door unlocks.
The Security LED stops flashing.
Open the driver’s door, insert the key into the ignition switch and turn it to “ON.” Roll down all the windows,
remove the key and exit the vehicle.
4
Arm and disarm the system with the remote
again, then wait 30 seconds.
The doors automatically relock.
The system automatically starts the arming process.
5
Press and release the remote control’s
unlock button again to stop the arming
process.
Refer to step 3
6
Insert the key into the driver’s door key
cylinder and turn it toward the front of the
vehicle to start the arming process.
All doors lock.
The Security LED lights up.
7
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
8
Reach inside and manually unlock the
driver’s door to trigger an alarm.
The driver’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
9
Manually unlock the driver’s door again and
hold it unlocked, open the door, then sit in
the driver’s seat.
The driver’s door lock attempts to lock repeatedly.
The horn continues to sound repeatedly.
The headlights and turn signal lights continue flashing.
The Security LED remains on.
10
Insert the key into the ignition switch and
turn it to “START” to stop the alarm.
The horn stops sounding.
All the lights stop flashing and/or turn off.
The Security LED turns off.
The starter cranks and the engine starts.
Turn the key back to “LOCK”, remove it, and then exit the vehicle.
11
With the door open, press the lock switch
on the door to lock the doors, then close the
door to start the system’s arming process.
All doors lock.
The Security LED lights up.
12
Wait 30 seconds.
Security LED starts flashing; the system is now armed.
Issue: C 07/25/12
Page 19 of 22
TOYOTA
TACOMA
2012–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
13
Reach inside and manually unlock the front
passenger’s door to trigger an alarm.
The front passenger’s door automatically relocks.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
14
Press and release the remote control’s
unlock button to stop the alarm.
The horn stops sounding.
All the lights stop flashing.
The Security LED stops flashing.
15
Press and release the remote control’s lock
button to start the system’s arming process,
then wait 30 seconds until the system is
armed.
Refer to steps 1 and 2.
16
Unlock and open one of the rear passenger
doors to trigger an alarm. (if available)
Refer to step 13.
17
Press and release the remote control’s
unlock button to stop the alarm.
Refer to Step 14
18
Repeat the above steps with the other rear
passenger door. (if available)
Refer to steps 1, 2, and 13.
Roll up all windows, remove the key and exit the vehicle.
19
Press and release the remote control’s lock
button to start the arming process.
Refer to step 1.
20
Wait 30 seconds.
After 30 seconds, the Security LED starts flashing; the
system is now armed.
Perform the following check in a temperature-controlled environment. (50°-90° F)
21
With the tip of a key, or Striker Tool pulled
all the way out (PPO only), tap the center
of the driver’s door window to trigger the
alarm.
The horn sounds repeatedly.
The headlights flash repeatedly.
The turn signal lights flash repeatedly.
The Security LED lights up.
22
Insert the key into the driver’s door key
cylinder and turn it toward the back of the
vehicle to stop the alarm.
Refer to Step 14
NOTE: If the alarm still does not trigger during the section test, increase the GBS sensitivity to the next setting and
test again.
NOTE: If you do not disarm the system, the alarm will last 20 seconds. It is not necessary to check the alarm duration.
Issue: C 07/25/12
Page 20 of 22
TOYOTA
TACOMA
2012–
CHECKLIST – these points MUST be checked to ensure a quality installation.
TVIP V5
RS3200 PLUS
Vehicle Function Checks
Function
Enter the Vehicle
□
□
Dome/Courtesy Lights
Horn
Start the Vehicle
□
□
Starter
Panel/Switch Illumination
Function
□
□
□
Steering Wheel Column Adjusts
Without Interference
Hood Latch Release
Gauges
□
ABS Light (if equipped)
□
Track/Skid Control Light (if equipped)
□
Tire Pressure Monitoring System
(TPMS)
If the warning light remains on, it may
indicate a system malfunction.
□
Lamp Failure Sensor
□
Seat Belt Warning Light
□
Air Bag Warning Light
Prior to TPMS activation and Pre-delivery
Service (PDS) of the Vehicle the TPMS light
will blink when IG is turned on.
Cruise Control Light (if equipped)
After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few
seconds and go off when IG is turned on.
□
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
If the warning light remains on, it may
indicate a system malfunction.
Using a Mirror or Assistant check the following.
□
□
□
□
Trunk/Tailgate/Bed Lights (if equipped)
Brake Lights
Backup Lights
□
□
□
If the warning light remains on, it may
indicate a system malfunction.
Tail Lights
Daytime Running Lights (if equipped)
Marker Lights
Clearance Sonar (if equipped)
Stop the Engine, Place the Vehicle’s IG in the ON position.
□
□
□
□
□
Hazard Lights
Head Light
High Beams
Power Side Mirrors (if equipped)
Power Sliding Door (if equipped)
Issue: C 07/25/12
□
□
□
□
□
Page 21 of 22
Turn Signal Lights
Fog Lights (if equipped)
Accessory Controls/Illumination (if equipped)
Convenience Memory Settings (if equipped)
Rear Sunshade (if equipped)
TOYOTA
TACOMA
2012–
CHECKLIST – these points MUST be checked to ensure a quality installation.
□
□
□
□
□
□
□
□
□
□
□
Function
Front Wiper/Washer
Power Sun/Moon Roof (if equipped)
Clock (if equipped)
Audio/Video (if equipped)
Steering Wheel Audio Control (if equipped)
Front Windshield Defogger (if equipped)
Side Mirror Defogger (if equipped)
□
□
□
□
□
□
□
RS3200 PLUS
Function
Rear Wiper/Washer (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
(if equipped)
Navigation System (if equipped)
HVAC
Rear Window Defogger (if equipped)
Accessory Power Socket (if equipped)
Heated/Vented Seats (if equipped)
Massage Seats (if equipped)
Glovebox Light (if equipped)
Power Locks (if equipped)
Power Seats (if equipped)
□
□
□
Remove the short pin after Function check.
Check with your Port/Dealer to see if this step is necessary.
Issue: C 07/25/12
Page 22 of 22
TVIP V5
Passenger Air Bag Switch (if equipped)
Power Windows (if equipped)
Key Sensor Buzzer
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement