instruction manual of iw001-wf-jjy

INSTRUCTION MANUAL DF-10WS V4
Rapid-Read Digital Thermometer Fork with flashlight
P. 1
Thank you for purchase of this Rapid-Read Thermometer Fork.
BATTERY INSTALLATION
1.
2.
3.
4.
Place your fork face down on a flat and soft surface.
Remove the battery cover at the back of your handle by pulling outward.
Insert 2 x new AAA batteries into the battery compartment by observing the correct
“+” and “-“ polarity.
Replace the battery cover until it clicks shut.
Remarks:

Do not mix old and new batteries.

Do not mix alkaline, standard or rechargeable batteries.

Alkaline batteries are recommended for optimal usage of this clock.
OPERATING INSTRUCTIONS
1. After batteries are installed, the lower LCD display shows the programmable SET temperature
you desire to cook (defaulted at 130°F) and the upper LCD shows the measured MEAT
temperature.
2. Press the + or - button on the side to set your desired temperatures. Press and hold + or – button
will accelerate the setting faster. The SET temperature range is 113°F to 199°F.
3. Insert both of the fork tines into the center of the meat (only one tine has sensor inside), or at least
0.5”, to assure an accurate reading. With meat of uneven thickness, such as boneless leg of lamb,
it will be necessary to probe both the thicker and thinner sections.
4. Press RAPID-READ / LIGHT once on the top of handle. The “MEAT” on the LCD is flashing and
the doneness LED’s are scrolling while the fork is computing the temperature.
5. In a few seoncds the measurement becomes stablised, the MEAT temperature reading is locked
and flashes and the doneness LED’s become static. After around 15 seconds, the doneness LED’s
will go off and the MEAT temperature will be unlocked, stop flashing and take a new reading.
6. When the MEAT temperature reaches or exceeds to the SET temperature, both readouts flash
when the MEAT temperature gets stablised.
P. 2
The five different colored doneness LED’s indicates the meat doneness by following the
temperature tables below (they are not related to the SET temperature):-
Remarks : the five colored doneness LED’s and the above mentioned lock function of MEAT
temperature only work when the measured temperature is 113°F (45°C) or above.
To change from Fahrenheit to Celsius, hold down both the Rapid Read light button and the
down temperature button on the side of the unit at the same time. Use the same method to
change back
to Fahrenheit.
TO USE THE FLASHLIGHT
Press RAPID-READ / LIGHT button once on the top of handle, the flashlight will be on for 15
seconds then it will go off. Keep pressing RAPID-READ / LIGHT will keep the flashlight on.
LOW BATTERY ALERT
When the battery level becomes low, an low battery icon will apear on the LCD display. Repalce
batteries with new alkaline batteries.
AUTO POWER OFF
Your thermometer fork will turn off automatically if no press of any button in 2 minutes. Press any
button to turn it on to use again.
TROUBLE SHOOTING
If your thermometer fork shows irrelevant temperature or does not function properly, which may be
caused by electro-static discharge or other interference, use a sharp object to press RESET at the
back of handle. Your unit will be reset to default settings and you need to set it again.
PRECAUTIONS
1. Do not touch the tines after use. The tines will be HOT.
2. Do not subject the housing or handle to prolonged high temperatures (most ovens over the grill).
The electronics inside the housing maybe damaged if subjected to prolonged high temperatures.
3. Clean the thermometer tines before each use to prevent cross contamination.
4. Wash tines with hot soapy water after final use.
P. 3
5. The thermometer fork is splash proof only. Do NOT submerge the handle in water or put it inside
dishwasher machine.
6. Do NOT leave the thermometer fork in hot oven.
BATTERY SAFETY & DISPOSAL
•
•
•
•
•
•
•
•
•
Dispose of batteries and electrical products responsibly at local authority household waste
recycling facility.
DO NOT dispose of batteries in a fire as the batteries may explode or leak.
Only use “AAA” 1.5V batteries.
Never use rechargeable batteries.
Replace all batteries at the same time, NEVER mix new and used batteries, different brands
or types.
Never try to dismantle batteries
Never short circuit batteries.
Exhausted batteries must be removed from the fork promptly.
Remove batteries from the product before extended storage
This symbol
indicates that this product, and any batteries, should not be disposed of in
normal household waste but taken to appropriate local recycling center, where available. Never
throw batteries in a fire or attempt to open outer casing
FCC Verification Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
LIMITED 90 DAY WARRANTY
This product is warranted by Maverick Industries, Inc. to be free from defects in material and
workmanship for a period of 90 days from the date of the initial use, considered to be not more than
thirty (30) days after the date of purchase. In the event of any claim under this limited warranty,
Maverick Industries, Inc., will repair or replace of it's sole option any unit or part (s) thereof, providing
such unit or part(s) are sent freight prepaid to the Customer Service Department, Maverick Industries,
Inc - DF-10 Super Fast Read Fork, 94 Mayfield Avenue, Edison, NJ 08837.
SPECIFICATIONS
Default settings:SET temperature
SET temperature range
Measuring range
Doneness’s LED working range
Temperature readout
Temperature resolution
Auto power off
130°F / 54°C
130°F to 199°F (55°C to 93°C)
32°F to 199°F (0°C to 93°C)
113°F to 199°F (45°C to 93°C)
°F (default)
1°F / 1°C
2 minutes (no press of any button)
DF-10WS V4, DEC 18, 2017
P. 4
Download PDF

advertising