Xerox Digital Color Press CED

Xerox 700 Digital Color Press
Version 1.0 System Software
Customer Expectations Document Launch Version 1.2
Document Version issued June 24, 2008
Includes:
•
Optional Oversized High Capacity Feeder (OHCF)
•
Optional High Capacity Feeder (HCF)
•
Optional Interface Module (IFM)
•
Optional High Capacity Stacker (HCS)
•
Optional Light Production C Finisher (LPC Finisher)
•
Optional CZ Folder (CZ Folder)
•
Optional Advanced Finisher
•
Optional Professional Finisher
Copyright 2008 Xerox Corporation
Copyright protection claimed includes all forms and matters of copyrighted material and information now allowed by statutory or judicial law or
hereinafter granted, including without limitation, material generated from the software programs that are displayed on the screen such as styles,
templates, icons, screen displays, looks, etc.
XEROX®, and all Xerox product names and product numbers mentioned in this publication are trademarks of XEROX CORPORATION. All non-Xerox
brands and product names may be trademarks or registered trademarks of the respective companies, and are hereby acknowledged.
Product appearance, build status and/or specifications are subject to change without notice
Revision History
Date
May 7, 2008
Author
Amy Taylor
Ver
1.0
Description
o Incorporated launch info, removed ECAT designation
May 14, 2008
Amy Taylor
1.1
o
Incorporated Marketing, Spares, OpCo feedback
o
Optimum Product Performance table:
o
Updated monthly print volume range to 20,00075,000 per Mike Madura
o
Updated service call rate per Sami Hanna
o
Verified IPM table with Mike Kelly
o
Recommended Supplies table:
o
Removed 220V-MN
o
Replaced BW and FC with words
o
Added note that 2 black cartridges are used in
tandem
o
Environmental and Electrical Requirements for optional
accessories verified with Rod Proulx
o
Dimensions for Common Configurations updated per Deb
Van Loan’s IPG draft 2
o
Optional Accessories table :
o
Added Light Production C Finisher with Booklet
Maker
o
Specified that CZ folder is available with Light
Production C Finisher or Light Production C Finisher with
Booklet maker
o
June 24, 2008
Amy Taylor
1.2
Advanced/Professional Finishers:
o
Added scuffing caveat per Rod Proulx
o
Added punch information
o
Added booklet info to Professional Finisher
o
Added power requirements to IFM and OHCF
o
Spelled out High Capacity Stacker in IFM description.
o
Added punch information and waste punch caveat to Light
Production C Finisher
o
Modified layout for readability
o
Changed server names per Mike Madura
o
Added warm-up time per Anna Askels’ request
o
Changed version number and date
o
Changed Light Production C Finisher booklet table to reflect
60 gsm - 80 gsm capability of 25 sheets
o
Noted that Bi-Fold and Booklets are unavailable in Copy
Mode
Launch Version 1.2, published 6/27/2008
2
o
Specified that sizes larger than 11 x 17” can not be offset on
Light Production C Finisher stack tray
o
Limitations/ Caveats table:
o
o
Added paper change/Sleep Mode note
o
Added Supplies/Faults notes
o
Added Tray 5 note
o
Added Punch Waste note
Productivity Speeds table :
o
o
Light Production C Finisher Caveats:
o
o
Specified that all internal trays are 64-220 gsm only
Added note to empty Purge tray after cancelling
booklet job
Added Fold accuracy information
Launch Version 1.2, published 6/27/2008
Table of Contents
Customer Expectations Document Launch Version 1.2
Revision History
Xerox 700 Digital Color Press
Centerline Paper
Optimum Product Performance
Print Volume Range
Product Specifications
Product Caveats/Limitations
Media Selection Guidelines
Media Support Documentation
Productivity Speeds- IPM (Impressions per Minute)
Image Quality
Non-Standard paper sizes
Duplex Prints
Paper/Throughput
Transparencies
Recommended Supplies
Initial Supplies
Environmental and Electrical Requirements
Electrical Requirements
Installation Considerations
Space Requirements
Calculating Space Required for Xerox 700 Digital Color Press
Mobility Plate
Physical Dimensions
Dimensions for Common Configurations of the Xerox 700 Digital Color Press:
Standard Configuration Features
Optional Accessories
Combination of Output Functions and Destinations
Optional High Capacity Feeder (HCF)
Optional Oversized High Capacity Feeder (OHCF)
Product Specifications (OHCF)
Advanced Finisher
Professional Finisher
Optional High Capacity Stacker (HCS)
Optional Interface Module (IFM)
Optional Light Production C Finisher (shown with Optional Booklet Maker)
Environmental and Electrical Requirements (Light Production C Finisher)
Light Production C Finisher Product Specifications
Light Production C Finisher Top Tray Capacity
Light Production C Finisher Stack Tray Capacity
Light Production C Finisher Bi-Fold Capability (available on Optional Booklet Maker)*
Optional C/Z Folder for the Light Production C Finisher
Interposer for the Light Production C Finisher
Hole Punching Capability for the Light Production C Finisher
Staple Capabilities by weight and paper finish for the Light Production C Finisher
Optional Booklet Maker for the Light Production C Finisher*
Light Production C Finisher Product Caveats/Limitations
Customer Agreement
Reference Material
Customer Support
Customer Training
Responsibility Matrix:
Customer Expectations Agreement
1
2
5
5
5
5
6
8
9
9
10
12
12
12
13
14
15
16
16
16
16
17
18
18
19
19
20
20
21
22
22
22
23
23
24
24
25
25
25
25
26
26
27
27
28
28
29
29
30
30
30
30
30
31
Xerox 700 Digital Color Press
Xerox 700 Digital Color Press
This section will help you understand the performance and capabilities of the Xerox 700 Digital Color Press.
Information on accessories will be reviewed later in this document.
All references to media capacity in this document are based on the Xerox Color Xpressions Plus (90 g/m2/24 lbs)
centerline paper. You will see the term “Centerline paper” several times in this document. “Centerline paper”
identifies the stock at the middle of the range of stocks that will deliver optimum performance for a given
characteristic, in this case machine stock capacity. Other paper weights and brands may alter capacity
capabilities.
Centerline Paper
Media Type
Uncoated paper
Coated paper
Xerox Equivalent
North America - Xerox Color Xpressions Plus (90 g/m2/24 lbs)
Europe – Colotech Plus (90 g/m2)
Xerox Color Xpressions Plus
centerline paper
North America – Xerox Digital Color Elite Gloss 80# Text (120
g/m2)
Xerox Color Xpressions Plus
centerline paper
Europe – Xerox Digital Color Elite Gloss 80# Text (120 g/m2)
Customers may obtain a copy of the Xerox Recommended Materials List for the Xerox 700 Digital Color Press by
going to Xerox.com and perform a search on the letters “RML”.
Optimum Product Performance
Print Volume Range
The Xerox 700 Digital Color Press is designed for an average monthly print volume (AMPV):
Press
AMPV
Conditions
Xerox 700 Digital Color Press
35,000
8.5 in x 11 in/A4
The Xerox 700 Digital Color Press is designed to produce a consistent uniform-looking color image. The Xerox
700 Digital Color Press is designed to operate in the range of 20,000 – 75,000 copies or prints per month. The
number of copies or prints between service calls on a digital color copier / printer is highly dependent on
customer expectations of quality and the use of applications and throughput materials. At an average usage of
35,000 copies or prints per month using centerline paper, it is expected that service will be required about once
every 5 weeks.
Launch Version 1.2, published 6/27/2008
5
Xerox 700 Digital Color Press
Product Specifications
The following table contains the specifications for the performance of the Xerox 700 Digital Color Press.
Item
Xerox 700 Digital Color
Press
Comments
• Internal tray capacity
• 3 trays; 550 sheet capacity each
• Represents capacity using Xerox Color
Xpressions Plus or Xerox Colotech+ centerline
paper.
• Paper Speeds of Media
Weight
for each paper weight
setting
(8.5 in x 11 in /A4 LEF
ppm)
• Productivity Mode Settings
• Refer to chart on page 10
• Transparency feeding
• 40 ppm b/w, 23 for color
• 3R5765 for USA and Canada; Xerox Europe:
3R93179. These premium transparencies are
specifically designed to provide optimum
copy quality.
• Use of other transparencies may cause
machine damage and result in excessive
service calls.
• Paper weight range
• 64-300 g/m2
• Paper Size
• Min: 5.5” x 7.2” (140mm x 182mm)
• Max: 13” x 19.2” (330mm x 488mm)
• Imageable Area
• Papers that are 80 g/m2 or lighter and less
than 210mm (8.3 in) may have increased
jam rates.
• Copy: Guaranteed Image Quality area is
297 mm x 432 mm (11.69 in x 17.00 in).
• Print: Guaranteed Image Quality area 317
mm x 480 mm (12.48 in x 18.90 in)
• The Xerox 700 Digital Color Press will
reproduce 11”x17” full bleed when printing
on 12x18” or 13”x19” paper and A3 full
bleed when printing on SRA3 paper. The
maximum length images (480 mm) are only
produced on media 19” long. On all media
there is a Lead Edge deletion of 4mm and a
Trail Edge deletion of 4mm. Side edge
deletion is 3mm except for 13x19” media.
On 13x19” media the side deletion is 3.5mm.
• Warm-up Time*
• 150 sec or less
After PowerOn or after SleepMode exit
• 30 sec or less
After LowPower mode exit**
Launch Version 1.2, published 6/27/2008
6
Xerox 700 Digital Color Press
• Resolution
• 2400 x 2400 x 1 dpi
Print Engine
• 600 x 600 x 1 dpi
Copy
• 600 x 600 x 1 dpi
Print (Gray Font only)
• Scanning Resolution
• 600 x 600 or less
• Several scan resolution settings are
selectable via Xerox 700 Digital Color Press
User Interface touch panel. Lower
resolutions will result in files that are smaller
in size and thereby reducing the customer's
network traffic.
• Color Consistency
• DeltaE = 7
• Within a page
• Service Call Rate
• At an average usage of 35,000
copies or prints per month on
centerline paper, it is expected that
service will be required about once
every 5 weeks.
• Actual service call rate is influenced by total
print volume, environmental conditions, area
coverage, and media characteristics.
• Shutdown Rate
• On average, less than 1 fault per day
requiring a power-recycle to recover.
• Based on 35,000 AMPV, one 8-hour shift per
day, using centerline papers.
• Offsetting Catch Tray
(Standard Output Device)
• 500 sheets
• Represents capacity using Xerox Color
Xpressions Plus or Xerox Colotech+ centerline
paper.
• Registration
• Printing registration specifications
are ±1.0 mm for front to back
registration (all paper trays except
MSI).
• Depending on paper stock, machine setup,
and other factors.
• (power-off power-on)
• Printing registration specifications
are ±3.0 mm for front to back
registration for MSI.
• Skew registration is ±1.0 mm along
200mm of the side edge in all trays
for an 8.5 x 11”/A4 LEF sheet of 24
lb.(90 g/m2)
• Meters
•
Color Impressions
•
Black Impressions
•
Color Large Impressions
•
Total Impressions
• The Digital Copier enables accurate billing of
black and white and color copied pages.
* Status where paper feed can be started immediately when Start button is pressed.
** When M/C exits from Low Power mode after 1 hour from change to Low Power Mode.
Launch Version 1.2, published 6/27/2008
7
Xerox 700 Digital Color Press
Product Caveats/Limitations
• The maximum print/copy speed for the system is determined by the process speed of the Xerox 700 Digital
Color Press engine; image quality adjustments are done frequently to maintain consistent IQ.
• As a printer / copier, the Xerox 700 Digital Color Press is a document printer; therefore, in reverse order (faceup) printing the print engine will not cycle up until the entire job is ready. This will impact First Copy Out Time
(FCOT). The printer may cycle down between each job depending on job complexity.
• When printing, overall system performance (‘Click to Clunk’ time) is primarily dependent upon the software
applications and network environment being used. Rasterizing (RIP-ing) is only a small fraction of Click to
Clunk time.
• Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause
machine damage or poor image quality. Using media at run modes other than that recommended for the
grade may cause poor image quality and serious machine damage.
• If the requested staple setting is outside machine capabilities, the copy job will not be stapled; print jobs will
be held at the DFE.
• 45-36x faults may occur intermittently. The expected frequency is approximately once every 20,000 prints or
once a week, depending on print volume. To recover, power off and power on the printer.
• 127-211 / 311 faults may occur after jam clearance. To recover, Power Off/ Power On the printer.
• System requirements messages (e.g., “Order Waste Toner Container”, “Hole Punch Waste Container Full”) may
occasionally be blocked by the current UI screen. Close the Job Status screen and open the Machine
Status/Supplies screen to check consumable status.
• If the machine stops running mid-job, or does not begin printing after a job is submitted, check the Machine
Status/Supplies screen to determine if supplies need to be replaced. The system will stop if sufficient supplies
are not available for a submitted job. If the problem persists, check the Machine Status/Fault screen, select
the fault, and click on the Instructions button.
• The system incorrectly directs the customer to call for service when the Hole Punch Waste Container or Staple
Waste Container is full. These containers are meant to be emptied by the customer.
• The Supplies screen incorrectly directs the customer to call for service when staples need replacing or when
the waste toner container needs to be replaced. Disregard the message, as these are customer-replaceable
items.
• The system does not prohibit duplexing coated substrates from the internal trays (Trays 1-3); however, there
can be a significant increase in jams or multifeeds. If large quantities of coated paper are to be run, the OHCF
is recommended for paper feeding.
• When using heavy coated 11’” x 17” stock, closing Trays 1-3 with too much force will result in a paper size
misread. Open and close the tray gently to allow the paper sensors to correctly identify paper size.
• If the adjustment arms are disturbed while re-loading paper in Tray 5, the paper size setting will return to
default and cause job to stop until the paper size setting is corrected by the user.
• If the paper is changed while the machine is in Sleep Mode, the machine may not register the change in
paper size. If this occurs, first open the side paper guide to the largest size, close and re-open the tray, then
adjust the side paper guide to the correct size.
Launch Version 1.2, published 6/27/2008
8
Xerox 700 Digital Color Press
Media Selection Guidelines
The following paper types are recommended to ensure you receive the best image quality from your Xerox 700 Digital
Color Press:
Media Type
Xerox Equivalent
• Uncoated
paper
• North America - Xerox Color Xpressions Plus (90 g/m2/24 lbs)
• Europe – Xerox Color Xpressions Plus (90 g/m2)
• Xerox Color Xpressions
Plus centerline paper
• Coated paper
• North America - Xerox Digital Color Gloss Coated Text (120 g/m2/80
lbs)
• Xerox Color Xpressions
Plus centerline paper
• Europe - Xerox Digital Color Colotech Gloss Coated (120 g/m2)
• Every effort has been made to ensure that the Xerox 700 Digital Color Press supports a broad range of media.
Keep in mind, however, that using only Xerox-recommended media maximizes reliability and paper-handling
performance.
• For further information and recommendations regarding media selection and handling, refer to the Material
Usage Guide provided with your system and the Recommended Materials List (RML) available from your
Xerox representative or on www.xerox.com.
• Typically, heavy weight papers exhibit increased variability of formation and surface smoothness, which may
result in degraded image quality.
Media Support Documentation
Media support documentation includes:
• Xerox 700 Digital Color Press Specialty Media Guide- Hints and Tips
• Recommended Materials Lists
• NA (North American) Customer Support / Escalation Process for media issues
• Materials Usage Guide
• The Paper Advantage Guide
• DMO (Developing Marketing Organization) Media testing support
• XE (Xerox Europe) Media testing support
These documents are available at http://www.xerox.com.
Launch Version 1.2, published 6/27/2008
9
Xerox 700 Digital Color Press
Productivity Speeds- IPM (Impressions per Minute)
Internal Paper Trays and
HCFs
A4 LEF,
B5 LEF
<=210
mm
8.5” x
11” LEF
<=216
mm
Uncoated
71
70
51
51
Duplex
46/46
• 221-256
g/m2 ‡
• 257-300
g/m2 ‡
• 177-220
g/m2
• 106-176
g/m2
• 177-220
g/m2
• 221-300
g/m2 ‡
Transparency
A3 SEF
11” x
17” SEF
<=432
mm
13” x
19.2”
<=488
mm
51
• 64-176 g/m2
Coated
Paper Size
A4 SEF, B4 SEF,
8.5” x
8.5” x
11” SEF 14” SEF
<=298
<=365
mm
mm
• B/W
w/ Finisher
• B/W
w/o Finisher
• Full Color
w/Finisher
• Full Color
w/o Finisher
Duplex
46/46
39
35
31
Duplex
46/46
35
30
25
22
51
51
35
30
25
22
35
35
25
21
17
15
51
51
Duplex
46/46
Duplex
46/46
35
30
25
22
35
35
Duplex:
31/31
Duplex:
31/31
25
21
17
15
35
35
25
21
17
15
40*
40
29
24
20
17
40*
40
29
24
20
17
18*
18
11
9
7
9*
9
7
6
5
13
8
*B5 not applicable
‡ does not apply to internal trays (Trays 1-3)
Launch Version 1.2, published 6/27/2008
10
Xerox 700 Digital Color Press
A4 LEF,
B5 LEF
MSI
<=210
mm
Uncoated
• 64-176 g/m
2
• 177-220
g/m2
• 221-256
g/m2
• 257-300
g/m2
Coated
• 106-176
g/m2
• 177-220
g/m2
• 221-300
g/m2
Transparency
• B/W
w/ Finisher
• B/W
w/o Finisher
• Full Color
w/Finisher
• Full Color
w/o Finisher
Paper Size
8.5” x 11” A4 SEF
B4 SEF
A3 SEF
LEF
8.5” x 11” 8.5” x 14” 11” x 17”
SEF
SEF
SEF
<=216
<=298
<=365
<=432
mm
mm
mm
mm
50
50
Duplex:
45/45
Duplex:
45/45
40
40
Duplex:
36/36
12.6” x
19.2”
<=488
mm
41
35
31
28
Duplex:
36/36
32
27
24
22
40
40
32
27
24
22
25
25
19
17
15
14
40
40
Duplex:
36/36
Duplex:
36/36
32
27
24
22
25
25
19
17
15
14
25
25
19
17
15
14
40
40
29
24
20
17
40
40
29
24
20
17
23
23
15
11
9
7
9
9
9
7
6
5
Launch Version 1.2, published 6/27/2008
11
Xerox 700 Digital Color Press
Image Quality
With its low melt EA toner properties and higher print speed, Xerox 700 Digital Color Press will produce output with a lower
gloss level that is consistent with offset.
• As with any printing process, artifacts will occur. These include streaks, mottle, banding, spots, etc. For most jobs and
clients, the expected level of artifacts is within the normal operational and component quality ranges of the system and
will not affect the acceptability of the job. Maintenance procedures are available to mitigate these artifacts.
• Random artifacts will occur.
• Artifact-sensitive jobs should be monitored.
• Using products on the Recommended Media List (RML) and maintaining your environment will also help to minimize the
occurrence of these artifacts.
• Color quality perception is subjective and will be affected by ambient lighting conditions.
• The appearance of the document displayed on the monitor screen may not match the output print because the monitor
uses RGB color space parameters.
• The customer is responsible for calibrating the Xerox 700 Digital Color Press.
The Xerox 700 Digital Color Press is optimized for most media; specific media may result in curl which can be corrected using
the internal de-curlers on the print engine and the optional Interface Module (IFM).
Non-Standard paper sizes
The DocuColor printer system supports non-standard paper sizes. However, due to rounding and unit-conversions that occur
in the client applications, print server, and printer, some mismatch may occur between the paper size entered at the
application, and the paper size that must be entered at the printer. The operator may need to adjust the entered paper
dimensions by up to 0.1 in (2.5 mm) in order for the printer to detect that the requested paper size has been loaded. In
addition, the printer interprets some paper sizes included in the PPD as non-standard sizes.
Duplex Prints
• The Duplexing Automatic Document Feeder (DADF) for hardcopy scanning will handle originals from 5.5 x 8.5” to 11 x
17” (or A3) in size, and from 16 to 28lb Bond in weight. The DADF has a maximum capacity of 250 sheets (based on 24lb
Paper).
• Automatic duplexing can be done on all sizes of media, up to 220 g/m2.
2
2
• Manual duplexing can be performed on media up to 110lb Cover (300 g/m ) or coated 100lb Cover (280 g/m ) from Tray
5 (Bypass).
• Manual duplex can be performed on media up to 13x19" (SRA3 320mmx450mm / Maximum 320mm x 482mm) from
Tray 5 (Bypass). (Note: Image quality degradation is possible above 220 g/m2.)
• As with any printer or copier, duplex performance is not expected to match the performance for single sided copying.
Paper jam rates may be higher than the rate you will experience for the same throughput material in single sided mode.
Launch Version 1.2, published 6/27/2008
12
Xerox 700 Digital Color Press
Paper/Throughput
For more detailed information on throughput materials, please refer to the Xerox Materials Usage Guide and the
Recommended Materials List.
Tray #
1-3
Size
• Min.: 5.5” x 8.5” SEF
(139mm x 215.9mm
SEF) (5.5” x 8.5” LEF
cannot be run)
Capacity (using
24lb / 90 g/m2
Paper)
• 550 sheets
• 64-220 g/m2
uncoated
106-220 g/m2 coated.
Higher jam rates (feed
rates and multi-feeds)
may occur on coated
paper in trays 1-3
• 250 sheets
• 64-300 g/m2 uncoated
106-300 g/m2 coated
• B5 up to 13” x
19.2”/SRA3
• 2,000 sheets
• 64-300 g/m2
uncoated
106-300 g/m2 coated
• B5 up to 13” x
19.2”/SRA3
• 4,000 sheets
• 64-300 g/m2 uncoated
106-300 g/m2 coated
• Max.: 13” x19.2”/SRA3
SEF
Tray 5
(Bypass)
Specified Weights
• Min: 100mm x
148mm (3.9” x 5.8”)
SEF
• Max: 13 x 19.2”
/SRA3 SEF
Tray 6
1 tray
Oversize
HCF
(Option)
Tray 6 &
Tray 7
2 tray
OHCF
(Option)
• Recommended paper to maximize image quality and product reliability is Xerox Color Xpressions Plus 24lb (smooth bright
white paper). This paper is specifically designed to maximize image quality and machine performance over a wide range
of environmental conditions.
• Attempts to feed heavier than recommended paper stocks, and/or misuse of the media settings, may cause machine
damage or poor image quality. Using media at run modes other than that recommended for the grade may cause poor
image quality and serious machine damage.
Launch Version 1.2, published 6/27/2008
13
Xerox 700 Digital Color Press
Transparencies
• The Xerox 700 Digital Color Press will feed 8.5 in x 11 in/A4 transparencies at a speed of 23 ppm color. Use Xerox
removable stripe transparency material (USA and Canada: 3R5765; Xerox Europe: 3R93179) for optimum system
performance and image projection. These premium transparencies are specifically designed to provide optimum copy
quality. Use of other transparencies may cause machine damage and result in excessive service calls.
• Due to the increased thickness of the removable stripe, no more than 100 transparencies should be loaded in a paper tray
at one time. The maximum output stack height should not exceed 100 transparencies.
Launch Version 1.2, published 6/27/2008
14
Xerox 700 Digital Color Press
Recommended Supplies
Supply
Description
Dry Ink: *
Reorder Number
WW
Metered
Toner
Reorder
Number
Western
Hemisphere/
Xerox Europe
Sold Toner
Reorder Number
Cartridges
Yield Projection
per Carton at representative total
area coverage
(using centerline
paper)
DMO Sold
Toner
Reorder
Number
30%
(7.5%
per color)
• Black
6R1375
6R1383
6R1379
1
20k per cartridge***
• Cyan
6R1376
6R1384
6R1380
1
22k
• Yellow
6R1378
6R1386
6R1382
1
22k
• Magenta
6R1377
6R1385
6R1381
1
21k
1
373k at 100%Black/White
Drum Cartridge**:
• Black
13R642
354k at 100% Color
• Cyan
13R643
1
156k
• Yellow
13R643
1
156k
• Magenta
13R643
1
156k
Toner Waste Bottle*
8R12990
Contact the Welcome Center for replacement
33k
1
Charge Corotron
13R637
1
175k
Fuser Module
8R13059
1
200k
Convenience and
Advance Staple
Cartridge
8R12964
1
5,000 staples
Convenience and
Advance Staple
Refills
8R12941
8R12941
8R12941
3 staple refills
(5,000 staples
each)
Light Production
Finisher Staples
8R13041
8R13041
8R13041
4 staple refills
(5,000 staples
each)
8R12925
4 staple refills
(5,000 staples
each)
Booklet Maker Staple
Refill
8R12925
8R12925
All Booklet makers (Advanced,
Professional and Light
Production) use this Staple
Refill
* The dry ink yield projections are based on the indicated area coverage at standardized conditions on 8.5 in x 11 in/A4
Xerox 700 Digital Color Press centerline paper. Please note that actual yields vary greatly depending on color intensity, area
Launch Version 1.2, published 6/27/2008
15
Xerox 700 Digital Color Press
coverage, paper stock, and mode selected.
** Drum Cartridge replacement frequency noted above for 8.5 in x 11 in/A4 images when using Xerox 700 Digital Color Press
centerline paper and other stocks with equivalent smoothness, cut quality and structure. Replacement rates may be more
frequent for operations which use high percentages of coated stocks, have area coverage greater than 70% of each color,
and/or larger than 8.5 in x 11 in/A4 size throughputs, e.g., 11 in x 17 in/A3.
*** One black cartridge per carton; two black cartridges are used in tandem, with a resulting yield of 40k.
Initial Supplies
• Each Xerox 700 Digital Color Press is delivered with an initial supply of Toner as well as the CRUs (Drum Cartridges,
Charge Corotron, Fuser, and Waste Toner Container as well as Staples – included for finishing options with stapling).
• To order additional Supply (toner / staples) or Throughput materials, contact the Xerox Supplies Marketing Center :
• 1-800-822-2200 US, 1-800-668-0199 CAN (English), 1-800-668-0133 CAN (French.)
• US Customers on Metered Price Plans should call the Metered Hotline, U.S. 1–800–599-2198 to acquire additional
toner.
Environmental and Electrical Requirements
Electrical Requirements
Area
Power Voltage (V)
Frequency (Hz)
XC
208-240V-10%/+6%
50/60+/-3%
XE
220-240V+/-10%
50/60+/-3%
Receptacle Diagram – The Xerox
700 Digital Color Press requires
the use of a 15-ampere, 2 pole 3wire grounding outlet. This is not
standard in most modern office
buildings and may require
professional installation. Consult
the diagram (right side) to help
in determining the proper outlet.
Installation by a qualified
electrician is recommended.
A single power cord (see above) is required for the Xerox 700 Digital Color Press. With the exception of the HCF, Advanced
Finisher and Professional Finisher, each optional feeding and finishing device requires an additional 100-240VAC minimum
240VA circuit with a Nema 5-15R receptacle (standard in US) or flying-leads.
Ground Fault Protection is provided which meets Xerox internal safety requirements and exceeds the Industry Standards for
Information Technology Equipment.
Installation Considerations
• Physical delivery of Xerox 700 Digital Color Press will be by a Xerox authorized “D/R” carrier. The carrier will install and
perform a functional check of the printer/copier unit. The carrier will review the software/documentation with the
customer. For the printer / copier the customer is responsible for connecting and configuring the equipment on their
network.
Launch Version 1.2, published 6/27/2008
16
Xerox 700 Digital Color Press
•
With the exception of the High Capacity Feeder, Advanced Finisher and Professional Finisher, (which plug directly into
the printer), each optional feeding and finishing device requires an additional 100-240VAC minimum 240VA circuit
with a Nema 5-15R receptacle (standard in US) or flying-leads.
•
There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead obstruction.
•
The unit weighs 583 lbs. (265 kg) - Printer, Scanner, and DADF. The Light Production Finisher with booklet maker,
interposer and folder is 392 lbs. (178 kg).
•
Electrical requirements and space requirements must be satisfied before the equipment is delivered.
•
One network drop is required for installation as a printer / copier.
•
Power cord length: 8.5 ft
•
Receptacle NEMA Part Number: 6-15R
Environmental Requirements
Environmental
Minimum
Maximum
Temperature
50º F (10º C)
82º F (28º C)
Humidity (non-condensing)
15% RH
85% RH
Better performance is achieved when conditions are maintained between 20-25 °C (68-77 °F) and 45-55% RH.*
50 Hz - 10,568 BTU/Hr (Running)
Heat Emission
Approximately 1,500 BTU/Hr
(Standby)
Noise Emission
55 dBA (Standby)
78 dBA
(Running)
Power Consumption
≅5.7 watts* (Sleep Mode)
2.2 kVA* (Continuous Running)
Altitude (above sea level)
0 ft (0 meters)
8,200ft. (2,500 meters)
Low Power Mode Power Usage
143 watts
≤300 Watts
Low Power Mode Recovery Time
-
30 seconds
Sleep Mode
-
≤95 Watts
60 Hz – 11,092 BTU/Hr (Running)
* Stated as an average. Warm up power consumption is 1,600 VA
Space Requirements
•
The Xerox 700 Digital Color Press system is non-movable when installed on any type of carpeting unless the optional
mobility plates are used. Details about the purchase of mobility plates are available from your Sales Representative.
•
All standard Xerox space requirements apply to this installation including overhead, shared, aisle or hallway, and
operator space. See “Calculating Space Required”, in the next section of this document.
•
A minimum of 24 inches (609.6 mm) should be maintained between the back of the machine (not the bustled
controller) and wall.
•
There should be a minimum of 78 inches (1,981 mm) clearance from the floor to the nearest overhead obstruction.
Launch Version 1.2, published 6/27/2008
17
Xerox 700 Digital Color Press
Calculating Space Required for Xerox 700 Digital Color Press
The dimensions listed below provide the overall service space required, including the space to the nearest obstruction. The
dimensions reflect both typical and hallway installations and are absolute minimums. The service area (including device
dimensions) from front to back is always 102”.
A
D2
D1
FEEDER
IOT
FINISHER
C
B
Service/Operational Space
Moveable
Installation
Stationary
Installation
A
Rear of Processor / System
10”
254 mm
24 ”
610 mm
B
Front of main Processor
56”
1422.4 mm
42 ”
1067 mm
C
Front of HCF and Finisher /
Folder
52”
1320.8 mm
38 ”
965 mm
D1
Left Side of System
13”
330 mm
13”
330 mm
D2
Right side of System Finisher
24”
610 mm
24”
610 mm
E
Allowable Height
78 ”
1981 mm
78 ”
1981 mm
Service Envelope: Width = Dimensions + D1 + D2; Depth = Depth + A + B
Installation Notes: A minimum of 24 inches (609.6 mm) should be maintained between the back of the machine
(not the bustled controller) and wall.
Mobility Plate
Carpeted flooring surfaces may require the installation of a mobility plate to allow the product to be moved during
normal maintenance activities
Launch Version 1.2, published 6/27/2008
18
Xerox 700 Digital Color Press
Physical Dimensions
The following table shows the overall physical dimensions of each module of the Xerox 700 Digital Color Press, including
space between the modules when connected into a system.
Module
Width
inches (mm)
Depth
inches (mm)
Height
inches (mm)
Weight
lbs (kg)
IOT/FFM
30 (762)
30 (762)
56 (1,423)
617.3 (280)
HCF
15 (381)
24 (610)
15 (381)
64 (29)
39(991)
30 (762)
39(991)
IFM
13.38 (340)
30 (762)
39(991)
Approx 25 ( Approx 11.34)
HCS
31.5 (800)
30 (762)
40 (1,016)
Approx 60 (Approx 27.2)
LPC Finisher
41.14 (1045)
30 (762)
44 (1,118)
231.5 (105)
w/ CZ Folder
49.02 (1245)
30 (762)
44 (1,118)
319.7 (145)
OHCF
1-tray :264.55 (120)
2-tray : 418.88 (190)
Dimensions for Common Configurations of the Xerox 700 Digital Color Press:
Configuration
Digital Press
Digital Press + Offset Catch Tray (OCT)
Bypass Tray + Digital Press
Bypass Tray + Digital Press + OCT
Bypass Tray + High Capacity Feeder (HCF) +
Digital Press + OCT
Bypass Tray + Digital Press + Advanced/
Professional Finisher
Bypass Tray + HCF + Digital Press +
Advanced/Professional Finisher
1-drawer Oversized High Capacity Feeder (OHCF)
+ Digital Press + Advanced/ Professional Finisher
2-drawer Oversized High Capacity Feeder (OHCF)
+ Digital Press + Advanced/ Professional Finisher
Bypass Tray + HCF+ Digital Press + Interface
Module + Light Production C Finisher (with
Booklet Maker) + C/Z Folder
Width*
Depth
Height
Weight
30 in.
30 in.
56 in.
661 lbs
762 mm
46 in.
1168 mm
52 in.
1320.8 mm
68 in.
1727 mm
762 mm
30 in.
762 mm
30 in.
762 mm
30 in.
762 mm
1423 mm
56 in.
1423 mm
56 in.
1423 mm
56 in.
1423 mm
300 kg
674 lbs
306 kg
661 lbs
300 kg
674 lbs
306 kg
68 in.
30 in.
56 in.
738 lbs
1727 mm
91 in.
2311.4 mm
91 in.
2311.4 mm
762 mm
30 in.
762 mm
30 in.
762 mm
1423 mm
56 in.
1423 mm
56 in.
1423 mm
333 kg
782/(851) lbs
355/(386) kg
846/(915) lbs
384/(415) kg
110 in.
30 in.
56 in.
1047/(1115.5) lbs
2794 mm
110 in.
2794 mm
762 mm
30 in.
762 mm
1423 mm
56 in.
1423 mm
475/(506) kg
1201/(1270) lbs
545/(576) kg
117 in.
30 in.
56 in.
1221 lbs
2972 mm
762 mm
1423 mm
554 kg
Launch Version 1.2, published 6/27/2008
19
Xerox 700 Digital Color Press
Configuration
Width*
Depth
Height
Weight
1-drawer OHCF + Digital Press + Interface
Module + Light Production C Finisher (with
Booklet Maker) + C/Z Folder
136 in.
30 in.
56 in.
1421 lbs
3454 mm
762 mm
1423 mm
664 kg
2-drawer OHCF + Digital Press + Interface
Module + Light Production C Finisher (with
Booklet Maker) + C/Z Folder
1-drawer OHCF + Digital Press + Interface
Module + High Capacity Stacker (HCS)
136 in.
30 in.
56 in.
1576 lbs
3454 mm
762 mm
1423 mm
715 kg
116 in.
2946.4 mm
116 in.
2946.4 mm
30 in.
762 mm
30 in.
762 mm
56 in.
1423 mm
56 in.
1423 mm
1287 lbs
584 kg
1441 lbs
654 kg
2-drawer OHCF + Digital Press + Interface
Module + High Capacity Stacker (HCS)
Standard Configuration Features
The Xerox 700 Digital Color Press is delivered with:
•
Print Engine with Scanner
•
Duplexing Automatic Document Feeder (DADF)
•
Controller connectivity enabled
•
Electronic Pre-Collation (EPC)
•
1,900 sheet paper capacity via 3 paper trays and MSI.
Optional Accessories
Accessory
Description
High Capacity
Feeder
2,000 sheet capacity (80 g/m2centerline paper)
1 Tray
Oversize High
Capacity
Feeder
2 Tray
Oversize High
Capacity
Feeder
Advanced
Finisher
Professional
Finisher
Interface
Module
2,000 Sheet* (up to 13x19.2/SRA3) capacity from 64-
300 g/m2 (uncoated) and 106-300 g/m2
(coated).
4,000 Sheet* (up to 13x19.2/SRA3) capacity from 642
2
300 g/m (uncoated) and 106-300 g/m (coated).
500 sheet top tray, 3,000 sheet stacker tray
500 sheet top tray, 1,500 sheet stacker tray, Up to 20
set booklet tray
The Interface Module aligns the paper paths of the
engine and finisher, cools and decurls paper exiting
the printer, and allows communication between the
engine and finisher. One Interface Module must be
ordered when an optional Light Production C
Finisher or High Capacity Stacker is ordered.
Launch Version 1.2, published 6/27/2008
20
Xerox 700 Digital Color Press
Light
Production C
Finisher
The Light Production C Finisher includes the punch
and stapler, the stacker tray and top exit tray,.
It also includes a built-in decurler unit that corrects the
curl on paper output from IOT and a built-in
interposer that feeds cover paper to finisher for
saddle-staple operation.
Light
Production C
Finisher with
Booklet
maker
C/Z Folder
High Capacity
Stacker
Foreign
Interface Kit
The Light Production C Finisher with booklet unit
includes the punch and stapler, the stacker tray and
top exit tray, and a booklet unit capable of saddle
stapling and bi fold.
It also includes a built-in decurler unit that corrects the
curl on paper output from IOT and a built-in
interposer that feeds cover paper to finisher for
saddle-staple operation.
An optional Folder unit that can handle Z-fold, Tri-C,
and Tri-Z, it can be added to the Light Production C
Finisher or the Light Production C Finisher with
Booklet maker
The C/Z folding tray can accommodate up to 40
2
sheets of 24 lb (90 g/m ) media).
Supported Paper sizes are 8.5x11” (A4)
2
Allows C/Z folding of media up to 24 lb (90 g/m )
uncoated.
Stack up to 5,000 sheets* offsetting output stack tray
with movable cart to move to off line finishing.
Additional cart is available for customer to order.
2
2
500 sheet* top tray, 64 g/m - 300 g/m , up to 13 x
19.2 (330x488mm)
Sample Set – 1.) Programmable at Color Server or 2.)
On-Demand at HCS User Interface‡
The Foreign Interface Kit enables the connection of
external devices such as auditrons or coin-op devices.
This will perform in copy and print modes.
2
Convenience
Staple up to 50 sheets of 90 g/m / 24 lb. Media.
Stapler
*based on 80 g/m2 centerline paper
‡ at launch this feature is available only with the FreeFlow server. Creo and EFI servers will offer this capability post-launch.
Combination of Output Functions and Destinations
Finisher
Top Tray
Stack
Tray
Staple
Hole
Punch
Booklet Bi-fold
Interposer
Advanced Finisher
o
o
o
o
Professional Finisher
Light Production C
Finisher (LPC Finisher)
o
o
o
o
o
o
o
o
o
LPC Finisher w/C-Z fold
LPC Finisher w/ Booklet
Maker
LPC Finisher w/ Booklet
Maker and C-Z fold
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
High Capacity Stacker
o
o
o
C-Z
Fold
o
o
o
Launch Version 1.2, published 6/27/2008
21
Xerox 700 Digital Color Press
Optional High Capacity Feeder (HCF)
•
•
•
•
•
2,000 sheet capacity (80 g/m2centerline paper)
220 mm(0.87 in) stack height
Powered by print engine – no external power source required
Maximum paper size 8.5 x 11 in./A4
Weight range: 52-216 g/m2 (uncoated)
Optional Oversized High Capacity Feeder (OHCF)
•
•
•
•
•
•
•
•
1 or 2 tray OHCF (each tray requires a fan kit)
Handles coated substrates up to 220 g/m2 for auto duplex
Air-assisted, robust feeder design for oversized and heavyweight
2,000 sheet capacity (80 g/m2 centerline paper)
Maximum paper size 13 x 19.2 in./SRA3
Weight range: from 64-300 g/m2 (uncoated) and 106-300 g/m2 (coated)
Maximum auto duplex up to 220 g/m2 /80 lb. cover, coated and uncoated
The OHCF requires a 100-240VAC minimum 240VA circuit. with a Nema 5-15R receptacle (standard in US)
or flying-leads
Product Specifications (OHCF)
Oversized High Capacity Feeder Module
Capacity:
1 tray, 2,000 sheets
Minimum Paper Weight:
64 g/m2 uncoated or 106 g/m2 coated
Maximum Paper Weight:
300 g/m2 coated or uncoated
Minimum Paper Size:
182mm x 210mm (7.2” x 8.3”)
Maximum Paper Size:
330mm x 488mm (13” x 19.2”)
Maximum Auto Duplex:
220 g/m2 80-lb cover (coated and uncoated)
Oversized High Capacity Feeder 2-Tray Module (shown with UI)
Capacity:
2 trays, 4,000* sheets (each tray capacity 2,000 sheets)
Minimum Paper Weight:
64 g/m2 uncoated or 106 g/m2 coated
Maximum Paper Weight:
300 g/m2 coated or uncoated
Minimum Paper Size:
182mm x 210mm (7.2” x 8.3”)
Maximum Paper Size:
330mm x 488mm (13” x 19.2”)
Maximum Auto Duplex:
220 g/m2 80 lb cover (coated and uncoated)
* (80 g/m2 centerline paper)
Launch Version 1.2, published 6/27/2008
22
Xerox 700 Digital Color Press
Advanced Finisher
•
•
•
•
•
•
500 sheet top tray, 3,000 sheet stacker tray
paper side registration ±6mm
staple paper stack height 5.7 mm (0.22 in)
50-sheet, multi-position stapling
The Advanced Finisher offers Hole Punch as a standard feature.
Hole punch capacity is equal to the regular capacity of the chosen output tray.
For the US, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is
available. Stacks can be punched on the left or right side, or on the top edge.
If hole punching fails, check to make sure that the punch waste container is
empty before calling for service.
Powered by print engine – no external power source required
52-216 g/m2 uncoated stock to all trays
217-280 g/m2 uncoated stock to top tray only
•
•
•
Professional Finisher
•
•
•
•
•
•
•
•
•
•
500 sheet top tray, 1,500 sheet stacker tray
paper side registration ±6mm
staple paper stack height 5.7 mm (0.22 in)
50-sheet, multi-position stapling
The Professional Finisher offers Hole Punch as a standard feature.
Hole punch capacity is equal to the regular capacity of the chosen output tray.
For the US, 2- and 3-hole punching is available; for Europe, 2- and 4-hole punch
is available. Stacks can be punched on the left or right side, or on the top edge.
If hole punching fails, check to make sure that the punch waste container is
empty before calling for service.
Powered by print engine – no external power source required
52-216 g/m2 uncoated stock to all trays
217-280 g/m2 uncoated stock to top tray only
Up to 20 set booklet tray:
Stapled: 15 sheets/set
Non-stapled: 5 sheets/set
Bi-Fold: 1 sheet/set, up to 169 g/m2 uncoated stock
Stackable number of sets depends on paper size
Launch Version 1.2, published 6/27/2008
23
Xerox 700 Digital Color Press
Optional High Capacity Stacker (HCS)
The HCS is designed for long production runs.
• Up to 5,000 sheets offsetting output stack tray with movable cart to move to off line
finishing. Additional cart is available for customer to order.
• Sample Set – 1.) Programmable at Color Server or 2.) On-Demand at HCS User Interface. At
launch this feature is available only with the Xerox FreeFlow Print Server for the Xerox
700. Xerox CX Print Server, Xerox EX Print Server, Integrated Fiery Color Server and
EFI Splash RPX-iii will offer this capability post-launch.
•
The HCS requires a 100-240VAC minimum 240VA circuit with a Nema 5-15R
receptacle (standard in US) or flying-leads.
• HCS Top Tray
HCS top tray
stack height
paper
weight
min:
max:
stack
weight:
500 sheets
2
<=80 g/m
100 x 148 mm
13 x 19.2 (in)
70 Kg (154 lb)
• HCS Stack Tray
Tray Capacity by weight and paper finish
Paper type and
weight
Paper Size
Smallest
size
A4
B4
A3
SRA3
203 x
182 Min
8.5 x 11
8.5 x 14
11 x 17
12 x 18
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
13 x 19.2
52-80
Uncoated
g/m2
81-300
g/m2
105-176
Coated
g/m2
177-220
g/m2
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
5,000
H=570mm
(22.44 in)
H=570mm
(22.44 in)
H=570mm
(22.44 in)
Optional Interface Module (IFM)
• The Interface Module aligns the paper paths of the engine and finisher, cools and decurls paper exiting
the printer, and allows communication between the engine and finisher. One Interface Module must be
ordered when an optional Light Production C Finisher or High Capacity Stacker is ordered.
• The Interface Module requires a 100-240VAC minimum 240VA circuit with a Nema 5-15R receptacle
(standard in US) or flying-leads.
• The Interface Module requires a 100-240VAC minimum 240VA circuit
Launch Version 1.2, published 6/27/2008
24
Xerox 700 Digital Color Press
Optional Light Production C Finisher (shown with Optional Booklet Maker)
This section provides the details and expectations for the optional
Light Production C Finisher that will be installed with your Xerox
700 Digital Color Press.
The Light Production C Finisher is an output device that can
process the following: 100-sheet stapling, 3,000 sheets stacking,
punch, saddle stapling/center-fold, optional Z-fold/three-fold, and
cover paper insertion.
The Light Production C Finisher has a built-in decurler unit that
corrects the curl on paper output from IOT, a built-in stapler with
staple-pin cut function, and a built-in interposer that feeds cover
paper to finisher for saddle-staple operation.
The Light Production C Finisher with optional booklet unit (shown
in photo) includes the punch and stapler, the stacker tray and top
exit tray, and a booklet unit capable of saddle stapling and bi fold.
Environmental and Electrical Requirements (Light Production C Finisher)
• The Light Production C Finisher requires a 100-240VAC minimum 240VA circuit with a Nema 5-15R receptacle
(standard in US) or flying-leads.
Light Production C Finisher Product Specifications
Light Production C Finisher Top Tray Capacity
Tray Capacity by weight and paper finish
Paper Size
Paper type
and weight
100 x
148 (mm)
2
52-80 g/m
2
80-300 g/m
2
105-80 g/m
177-280
g/m2
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
A4
B4
A3
8.5 x 11
(in)
8.5 x 14
(in)
11 x 17
(in)
SRA3
12 x 18
(in)
330 x
488 (mm)
13 x 19.2
(in)
500
500
500
500
500
500
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
H=67mm
(2.64 in)
Launch Version 1.2, published 6/27/2008
25
Xerox 700 Digital Color Press
Light Production C Finisher Stack Tray Capacity
Number of Sheets by weight and paper finish
Paper type and weight
Paper Size
Smallest size
A4
B4
A3
SRA3*
182X257mm 8.5 x 11 (in) 8.5 x 14 (in) 11 x 17 (in) 12 x 18 (in)*
2
Uncoated
52-80 g/m
2
80-300 g/m
Coated
2
105-176 g/m
2
177-280 g/m
*Cannot be offset
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
3,000
H=378mm
(14.88 in)
H=378mm
(14.88 in)
H=378mm
(14.88 in)
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
13 x 19.2
(in)*
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
Light Production C Finisher Bi-Fold Capability (available on Optional Booklet Maker)*
Paper type and weight
Uncoated
Coated
Booklet Tray Capability by weight, size and paper finish
A4
B4
A3
8.5 x 11
(in)
8.5 x 14
(in)
11 x 17
(in)
12 x 18
(in)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
60-80 g/m
2
81-90 g/m
2
91-105 g/m
2
106-128 g/m
2
129-150 g/m
2
151-176 g/m
2
177-220 g/m
2
221-256 g/m
2
256-300 g/m
2
105-128 g/m
2
129-150 g/m
2
151-176 g/m
2
105-200 g/m
2
200-280 g/m
SRA3
*Unavailable in Copy Mode
Fold accuracy (lead and side edge): ≤2.5 mm
Bi-Fold: 1 sheet/set, 60-300g/m2 uncoated stock, 105-280 g/m2 coated stock
Launch Version 1.2, published 6/27/2008
26
1,500
H=180mm
(7.09 in)
H=180mm
(7.09 in)
H=180mm
(7.09 in)
Xerox 700 Digital Color Press
Optional C/Z Folder for the Light Production C Finisher
An optional Folder unit that can handle Z-fold, Tri-C, and Tri-Z, it can be added to the Light Production C Finisher.
•
2
The C/Z folding tray can accommodate 30 sheets of up to 24 lb (90 g/m ) uncoated media.
•
Supported Paper size is 8.5x11” (A4) to the bottom tray, 11 x 17” (A3) to the top tray
•
Fold accuracy as shown below:
Z-Fold
2 mm±2mm
±1.0mm
±1.5 mm
1/2Paper
+0/-4 mm
Envelop C-Fold
±1.5 mm
±1.5 mm
8 mm
±2mm
2 mm
±2mm
Interposer for the Light Production C Finisher
•
The Light Production C Finisher includes a standard Interposer, used to insert pre-printed stock into finished sets
without having to go through the engine. Labels, coated media & envelopes are not supported
Tray Capacity by weight, size and paper finish
Paper type and weight
Paper Size
B5
Uncoated
2
60-220 g/m
2
81-220 g/m
200 shts
H=22mm
(0.87 in)
A4
8.5 x 11
(in)
B4
8.5 x 14
(in)
200 shts
H=22mm
(0.87 in)
200 shts
H=22mm
(0.87 in)
A3
11 x 17
(in)
200 shts
H=22mm
(0.87 in)
Launch Version 1.2, published 6/27/2008
27
Xerox 700 Digital Color Press
Hole Punching Capability for the Light Production C Finisher
The Light Production C Finisher offers Hole Punch as a standard feature.
•
Hole punching is not available to the Booklet Tray.
•
Hole punch capacity is equal to the regular capacity of the chosen output tray.
•
For the US, 2- and 3-hole punching is available; for Europe, 2- and 4- hole punch is available. Stacks can be
punched on the left or right side, or on the top edge.
Tray Capacity by weight and paper finish
Paper type and weight
Paper Size
B5
Uncoated
Coated
2
52-200 g/m
2
105-200 g/m
A4
B4
A3
8.5 x 11
(in)
8.5 x 14
(in)
11 x 17
(in)
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Applicable
Staple Capabilities by weight and paper finish for the Light Production C Finisher
Staple Capabilities by weight and paper finish
Paper type and weight
Paper Size
Smallest
size
203.2x254
(mm)
Uncoated
B4
A3
8.5 x 11
(in)
8.5 x 14
(in)
11 x 17
(in)
2
100
100
100
100
2
up to 100
up to 100
up to 100
up to 100
52-80 g/m
81-90 g/m
2
91-105 g/m
50
50
50
50
2
30
30
30
30
2
19
19
19
19
2
12
12
12
12
2
5
5
5
5
2
4
4
4
4
2
3
3
3
3
2
5
5
5
5
2
5
5
5
5
2
5
5
5
5
2
5
5
5
5
2
4
4
4
4
2
3
3
3
3
106-128 g/m
129-150 g/m
151-176 g/m
177-220 g/m
221-256 g/m
256-300 g/m
Coated
A4
106-128 g/m
129-150 g/m
151-176 g/m
177-220 g/m
221-256 g/m
256-300 g/m
Launch Version 1.2, published 6/27/2008
28
Xerox 700 Digital Color Press
Optional Booklet Maker for the Light Production C Finisher*
Tray Capacity by weight, size and paper finish
Paper type and weight
Paper Size
A4
8.5 x
11 (in)
Uncoated
Coated
2
60-80 g/m
2
81-90 g/m
2
91-105 g/m
2
106-128 g/m
2
129-150 g/m
2
151-176 g/m
2
177-220 g/m
2
221-256 g/m
2
256-300 g/m
2
106-128 g/m
2
129-150 g/m
2
151-176 g/m
2
177-220 g/m
2
221-256 g/m
2
256-300 g/m
*Unavailable in Copy Mode
B4
A3
8.5 x
11 x
14 (in) 17 (in)
SRA3
12 x
18 (in)
25
20
10
10
10
10
5
4
3
10
25
20
10
10
10
10
5
4
3
10
25
20
10
10
10
10
5
4
3
10
25
20
10
10
10
10
5
4
3
10
25
20
10
10
10
10
5
4
3
10
10
10
10
10
10
10
10
10
10
10
5
5
5
5
5
4
4
4
4
4
3
3
3
3
3
Fold accuracy of the inner sheet (lead and side edge):
Stapled: ≤1.5 mm for A4 sheets, ≤2.0 mm for other sizes
Non-stapled: ≤1.5 mm
Stapled: 25 sheets/set
Non-stapled: 5 sheets/set
Light Production C Finisher Product Caveats/Limitations
• If the compiler tamper arm resets itself during a job, the job will need to be re-submitted
• If hole punching fails, check to make sure that the punch waste container is empty before calling service
• After cancelling a job sent to the Booklet maker, empty the purge tray (located inside the Light Production C Finisher)
before submitting another print job. This will ensure that purged sheets are not inadvertently inserted into the next
booklet printed.
Launch Version 1.2, published 6/27/2008
29
Xerox 700 Digital Color Press
Customer Agreement
Reference Material
Xerox 700 Digital Color Press is shipped with a complete set of user guides on a CD ROM.
Customer Support
The Xerox Customer Support Centers are available to provide general information, answer questions and take service calls. You
can reach the Customer Support Center at the following toll-free phone numbers:
United States
1-800-821-2797
Canada
1-800-939-3769
To order Replacement Customer Replaceable Units (CRUs):
Full Service Maintenance customers order replacement CRU’s through Xerox Customer Support Center using the toll free number
above. Time and Materials Maintenance customer order replacement CRU’s through the Logistics Customer Support Center at 1800-828-5881.
To order additional Supply (toner / staples) or Throughput materials: The Xerox Supplies Marketing Center, 1-800-822-2200
US, 1-800-668-0199 CAN (English), 1-800-668-0133 CAN (French) is available for ordering Xerox supplies, including paper and
other throughput material.
US Customers on Metered Price Plans should call the Metered Hotline, U.S. 1–800–599-2198 to acquire additional toner.
Customer Training
Customer training on machine features and functions is a purchasable service for the Xerox 700 Digital Color Press.
Responsibility Matrix:
Action
Communicate the need for adequate space and power
to accommodate the Xerox 700 Digital Color Press and
accessories.
Provide adequate space and power to configure the
Xerox 700 Digital Color Press.
Unpack system / components
Install system hardware
Connect all System Components prior to powering up
the system
Install the printer description files and server, status
Desktop Accessories on Client (Printer only)
Ensure network configuration (Printer only)
Confirm network integrity (Printer only)
Acquire and install client workstation network software
(Printer only)
Run initial software diagnostics when directed
Monitor and adjust as required
Load any additional fonts (Printer only)
Order and replace Customer Replaceable Units (Drum
cartridges, Fuser and Waste Toner Cartridge) as
needed.
Provide Help Line support (with purchase of FSMA)
Provide spared parts (with purchase of FSMA)
Provide service (with purchase of FSMA)
Return failed or expended parts and cartridges
Customer
Xerox
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Launch Version 1.2, published 6/27/2008
30
Xerox 700 Digital Color Press
Customer Expectations Agreement 1
Check off the modules that will be part of this install and for which expectations have been set:
_____ Xerox 700 Digital Color Press
______ Optional CZ Folder (CZ Folder)
_____ Optional High Capacity Feeder
______ Optional High Capacity Stacker (HCS)
_____ Optional Oversized High Capacity Feeder (1or 2- Tray)
______ Xerox FreeFlow Print Server for the Xerox
700
_____ Optional Interface Module (IFM)
______ Xerox CX Print Server, Powered by Creo for
the Xerox 700
_____ Optional Advanced Finisher
_____ Optional Professional Finisher with Booklet
Maker
_____ Optional Light Production C Finisher (LPC
Finisher)
_____ Optional Light Production C Finisher (LPC
Finisher) with Booklet Maker
______ Xerox EX Print Server, Powered by Fiery for
the Xerox 700
______ Integrated Fiery Color Server
______ EFI Splash RPX-iii (Requires passing data
through the Xerox EX Print Server or
Integrated Fiery Color Server)
Primary Customer Applications:
Special considerations or performance limitations identified by Xerox and agreed to by the customer:
I have reviewed and understand the product specifications for each of the modules
that will be installed: (Signatures Required)
________________________________________________________
Customer
________________________________________________________
Xerox Sales Representative
________________________________________________________
Xerox Customer Service Representative
I have viewed a representative output sample from the Xerox 700 Digital Color Press and the
image quality is acceptable for the needs of my organization:
(Signature required if Xerox 700 Digital Color Press is included with Order)
________________________________________________________
Customer
1
A separate CED must be filled out and signed for the print server.
Launch Version 1.2, published 6/27/2008
31