danger - Condor Fireplace &

Owner’s Manual
Care and Operation
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Models:
SL-5F
SL-7F
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
DANGER
HOT GLASS WILL
CAUSE BURNS.
This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home
Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.
This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See appliance installation manual for additional
Commonwealth of Massachusetts requirements.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
1
1
Welcome
Read this manual before operating this appliance.
Please retain this Owner’s Manual for future reference.
Read the Installation Manual before making any installation or finishing changes.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Heat & Glo gas fireplace, an
elegant and clean alternative to wood burning fireplaces.
The Heat & Glo gas fireplace you have selected is designed
to provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Heat & Glo gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of fireplace products!
Local Dealer Information
DEALER: Fill in
your name, address,
phone and email
information here and
appliance information
below.
Dealer Name: ________________________________________________________
Address: ____________________________________________________________
____________________________________________________________
Phone: _____________________________________________________________
Email: _____________________________________________________________
Appliance Information:
Brand: ________________________________________________ Model Name: ___________________________
Serial Number:__________________________________________ Date Installed: __________________________
Listing Label Information/Location
Type of Gas
Gas and Electric
Information
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz)
Gaz)::
NATURAL GAS
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
Model Number
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
1 Welcome
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Product Specific Information
A. Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
B. Glass Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
C. BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 Important Safety and Operating Information
A. Appliance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
B. General Operating Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 8
C. Fuel Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
D. Good Faith Wall Surface/TV Guidelines . . . . . . . . . . . . . . 8
E. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 10
F. Lighting Instructions (IPI) . . . . . . . . . . . . . . . . . . . . . . . . . 11
G. Appliance Break-In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
H. Heat Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
I. Operation During A Power Outage . . . . . . . . . . . . . . . . . . . 13
J. Detailed Component Operating Instructions - IntelliFire . . 13
4 Maintenance and Service
A. Maintenance: Frequency and Tasks . . . . . . . . . . . . . . . . 14
B. Maintenance Tasks - Homeowner . . . . . . . . . . . . . . . . . . 14
C. Maintenance Tasks - Qualified Service Technician . . . . . 16
5 Frequently Asked Questions and Troubleshooting
A. Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 17
B. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Reference Materials
A. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
B. Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
C. Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
 = Contains updated information.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
3
B. Limited Lifetime Warranty
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
X
X
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
Ignition Modules
Firepots and burnpots
X
5 years
Components Covered
Electric Venting
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645H 10/15
4
Page 1 of 2
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
•
•
•
•
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
This warranty is only valid while the HHT appliance remains at the site of original installation.
This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints
related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Information is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consideration must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
•
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645H 10/15
Page 2 of 2
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
5
2
Product Specific Information
A. Appliance Certification
MODELS: SL-5F, SL-7F
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Heater
STANDARD: ANSI Z21.88-2014/CSA 2.33-2014
This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
C. BTU Specifications
Models
(U.S. or Canada)
Minimum
Input
BTU/h
Orifice
Size (DMS)
SL-5F
(NG)
(0-2000 FT)
17,500
12,000
45
SL-5F
(LP)
(0-2000 FT)
17,000
13,500
1.25 mm
SL-7F
(NG)
(0-2000 FT)
24,000
16,500
42
SL-7F
(LP)
(0-2000 FT)
20,500
16,500
54
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
B. Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the
Consumer Product Safety Commission (CPSC). The
tempered glass has been tested and certified to the requirements of ANSI Z97.1 and CPSC 16 CFR 1202
(Safety Glazing Certification Council SGCC# 1595 and
1597. Architectural Testing, Inc. Reports 02-31919.01
and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
6
Maximum
Input BTU/h
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
3
Important Safety and Operating Information
A. Appliance Safety
WARNING! DO NOT operate fireplace before reading
and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
• Keep children away.
• CAREFULLY SUPERVISE children in same room
as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Clothing, furniture, draperies, and other flammable
materials must not be placed on or near the
appliance.
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
• Teach children to NEVER touch the fireplace.
• Consider not using the fireplace when children will be
present.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
• Turn off wall controls.
• Unplug 3 volt adapter plug (IPI) and remove batteries on
IPI models.
Clear Space
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 3.1.
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals. DO NOT operate the appliance with
the barrier removed. If the barrier becomes damaged,
the barrier shall be replaced with the manufacturer’s
barrier for this appliance.
CLEAR SPACE
3 FT. IN
FRONT OF
FIREPLACE
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
Young children should be carefully supervised when they
are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns.
• A physical barrier is recommended if there are at risk
individuals in the house.
• To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away
from hot surfaces.
Figure 3.1 Clear Space
Over Firing
The appliance is considered to be over firing if the flames
are contacting the top of the firebox. Call a qualified service
technician to service the appliance
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
7
D. Good Faith Wall Surface/TV Guidelines
B. General Operating Parts
Figure 3.5 references the general operating parts of the
appliance and the section of this manual in which they are
discussed.
TO CEILING
116°F
117°F
FIREPLACE
OPENING
120°F
122°F
48 in.
42 in.
125°F
36 in.
128°F
30 in.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 4.B.
132°F
142°F
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 4.B.
24 in.
18 in.
12 in.
6 in.
MANTEL
(See Appliance
Installation Manual)
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
APPLIANCE FRONT
FAN KIT
SECTION 3.H
Figure 3.5. Good Faith Wall Surface Temperatures Above Appliance
HEARTH
CLEAR SPACE
SECTION 3.A
CONTROL CAVITY
SECTION 3.H
NOTICE: Temperatures listed above are taken with a
temperature measuring probe as prescribed by the test
standard used for appliance certification. Temperatures
on walls or mantels taken with an infrared thermometer
may yield increased temperatures of up to 30 degrees or
more depending on the thermometer settings and material
characteristics being measured.
Figure 3.2 General Operating Parts
C. Fuel Specifications
WARNING! Risk of Fire or Explosion! Appliance must
be set up for compatible gas type!
• This appliance is designed to operate on either natural
gas or propane. Make sure the appliance is compatible
with gas type selected for installation site.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
8
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Good Faith Guidelines for TV Installa on’s above a Typical Gas Fireplace
TV recessed into the wall
TV on the wall
TV
TV Wall
Bracket
Item
A
B
C
D
A
Minimum Dimensions
2.5 inches
2 inches minimum to 3 inches
maximum
18 inches
Wall Brkt + TV Thickness + 2.5
inches
B
B
Mantel
D
A
C
Fireplace
C
Fireplace
Notes:
1. These are good faith recommended clearances only and not a guarantee of compliance with all TV
manufacturers’ maximum allowable opera ng temperatures.
2. Since every home has unique air flow characteris cs and maximum allowable opera ng temperatures
can vary from manufacturer to manufacturer and from model to model, actual TV temperatures should
be validated at the me of each installa on. TVs should not be used in situa ons where the actual TV
temperature exceeds the manufacturers’ maximum allowable opera ng temperatures iden fied in the
TV’s technical specifica ons. Contact the TV’s manufacturer directly if you cannot locate this
informa on or have ques ons regarding the informa on.
3. Mantel height and depth must conform to mantle requirements ƐƉĞĐŝĮed in the fireplace installa on
manual.
4. “C” dimension taken from the top of the hood or ĮƌĞƉůace opening.
5. Sugges ons on how to further reduce TV temperatures:
a. Increase “A” dimension.
b. Increase “C” dimension, however, increasing “B” dimension beyond maximum recommended
typically results in higher temperatures.
Figure 3.4. Good Faith TV Guidelines
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
9
E. Before Lighting Appliance
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/
or other decorative materials.
• Check the wiring.
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
10
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
F. Lighting Instructions (IPI)
The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery
life, remove them when using the transformer.
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an intermittent pilot ignition (IPI) device which
automatically lights the burner. DO NOT try to light the burner by hand.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell
next to the floor because some gas is heavier than air and will settle on the floor.
• If you cannot reach your gas supplier, call the fire department.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do not use any phone in your building.
C. Use only your hand to push in or turn the gas control knob. Never use tools. If
the knob will not push in or turn by hand, DO NOT try to repair it, call a qualified
service technician. Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any part of
the control system and any gas control which has been under water.
LIGHTING INSTRUCTIONS (IPI)
1.
This appliance is equipped with an ignition device which
automatically lights the burner. DO NOT try to light the burner by hand.
GAS
VALVE
2.
Wait five (5) minutes to clear out any gas. Then smell for gas, including near the
floor. If you smell gas, STOP! Follow “B” in the Safety Information located on the
top of this label. If you do not smell gas, go to next step.
3.
To light the burner:
Equipped with wall switch: Turn ON/OFF switch to ON.
Equipped with remote or wall control: Press ON or FLAME button.
Equipped with thermostat: Set temperature to desired setting.
4.
If the appliance does not light after three tries, call your service technician or gas
supplier.
TO TURN OFF GAS TO APPLIANCE
1.
Equipped with wall switch: Turn ON/OFF switch to OFF.
Equipped with remote or wall control: Press OFF button.
Equipped with thermostat: Set temperature to lowest setting.
2.
Service technician should turn off electric power to the control when performing
service.
DANGER
HOT GLASS WILL CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL COOLED.
NEVER ALLOW CHILDREN TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
WARNING:
CAUTION:
DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CONTROL VALVE.
Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline
and other liquids having flammable vapors away.
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to the owner’s information manual provided with
this appliance. For assistance or additional information, consult a qualified installer,
service agency or the gas supplier.
DO NOT operate the appliance with fixed glass assembly removed, cracked or
broken. Replacement of the fixed glass assembly should be done by a licensed or
qualified service person.
This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or fuel combustion which
are known to the State of California to cause cancer, birth defects, or other reproductive
harm.
NOT FOR USE WITH SOLID FUEL
For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel.
Also Certified for Installation in a Bedroom or a Bedsitting Room.
This appliance must be installed in accordance with local codes, if any; if none,
follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and
Propane Installation code, CSA B149.1.
Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
593-913i
11
G. Appliance Break-In
H. Heat Management
Follow the initial break-in procedure below to cure the
materials used to manufacture the fireplace and the
fnishing materials around it.
Heat Output
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to cool completely.
• Remove fixed glass assembly. See Section 4.B.
• Clean fixed glass assembly. See Section 4.B.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
Note: Some IPI systems have a safety feature that
automatically shuts down the fireplace after 9 hours of
continuous operation without receiving a command from
the remote control. If this occurs, restart the appliance.
The SL-5F and SL-7F models have a variable burn
rate which is controlled by the HI/LO knob on the gas
valve. Therefore the flame height is adjustable. The HI/
LO knob is shown in Figure 3.5. It is located in the control
cavity of the appliance. The HI/LO knob may be adjusted
as desired by turning counterclockwise to the HIGH
position and by turning clockwise to the LO position.
If an optional fan is installed, the fan speed is controlled
by adjusting the speed control knob. Turn the knob
clockwise to increase the fan speed and counterclockwise
to decrease the fan speed.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
VALVE
LOCATION
Figure 3.5 Control Cavity/Valve Location
12
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
CONTROL
CAVITY
I. Operation During A Power Outage
The IntelliFire intermittent pilot ignition system comes
with a battery backup system that enables the system
to operate in a power outage. A factory-installed battery
pack is located in the control cavity of the appliance. See
Figure 3.3. Batteries should not be placed in the battery
tray while using electrical power to operate the fireplace.
Remove batteries from battery tray when power has been
restored.
NOTICE: Batteries should only be used as a power source
in the event of an emergency power outage. Batteries
should not be used as a primary long-term power source.
To Operate Fireplace Using Battery Power (DC):
1. Access the control cavity of the appliance. See Figure
3.5 for location. The decorative front may need to be
removed.
2. Locate the battery tray in the control cavity and insert
two D cell batteries. Battery polarity must be correct or
module damage will occur. See Figure 3.5. A complete
wiring diagram is included in the Electrical section of
the appliance Installation Manual.
3. Turn the appliance on according to the instructions
below for the appropriate type of control:
Standard Wall Switch or Factory-Installed ON/OFF
Switch:
•
Toggle the switch as you would under normal
circumstances.
Multifunctional Wired Wall Switch Control System:
•
Locate the wired wall switch control module in control
cavity.
•
Locate battery operation switch on the side of the
module.
•
Slide the switch to the BATTERY ON or ON position.
Wireless Remote:
•
Locate the remote control module in the control cavity.
•
Slide the ON/REMOTE/OFF switch to the ON position.
NOTICE: Some functionality will be lost when using battery
backup including remote control, fan, lights, or any other
auxiliary functions that require household 110-120 VAC
power.
To Return to Operation Using Electrical (AC) Power
Standard Wall Switch or Factory-Installed ON/OFF
Switch:
•
Toggle the switch to OFF and remove the batteries
from the battery tray. Replace decorative front on
appliance.
Multifunctional Wired Wall Switch Control System:
•
Slide the switch to the OFF position. Remove the
batteries from the battery tray. Replace decorative
front on appliance.
Wireless Remote:
•
Slide the ON/REMOTE/OFF switch to the REMOTE
position. Remove the batteries from the battery tray.
Replace decorative front on appliance.
J. Detailed Component Operating Instructions - IntelliFire
IntelliFire™ Ignition System
Intellifire™ is an intermittent pilot ignition, which is an
electronic system. The term Intermittent is used because
the pilot burner flame is only present when the main
burner is operating. When the main burner is off, the pilot
is also off.
NOTICE: Batteries should not be placed in the battery
pack while using the transformer. Remove batteries before
using the transformer, and unplug the transformer before
installing the batteries. Battery polarity must be correct or
module damage will occur.
Appliance ON/OFF
A wall control, thermostat or remote control may be
used to control the ON/OFF function of the appliance.
Follow instructions included with the installed control.
Optional Fan Kit
If desired, a fan kit may be added. Contact your dealer
to order the correct fan kit. Heat management for the fan
is discussed in Section 3.H. Detailed instructions are included with the fan kit.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
13
4
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Glass Cleaning
Frequency: Seasonally
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
By: Homeowner
A. Maintenance: Frequency and Tasks
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
Task
Glass Cleaning
DecorativeFronts/
Surrounds
Frequency
To be completed by
Seasonally
Annually
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
Remote Control
Seasonally
Venting
Seasonally
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Gasket Seal and
Glass Inspection
Annually
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
Log Inspection
Annually
• Remove decorative front from fireplace and set aside
on work surface.
Firebox
Inspection
Annually
Control
Compartment &
Firebox Top
Annually
Burner Ignition &
Operation
Annually
Homeowner
Qualified Service
Technician
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
Removing Fixed Glass Assembly
B. Maintenance Tasks - Homeowner
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
CAUTION! Risk of Burns! The fireplace should be
turned off and cooled before servicing.
• Pull the four glass assembly latches out of the groove
on the glass frame. Remove glass door from the appliance. See Figure 4.1.
Cleaning Fixed Glass Assembly
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove
on the glass frame. See Figure 4.1.
• Reinstall decorative front.
14
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Venting
Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
LATCHES
(BOTH BOTTOM
AND TOP)
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds).
• Inspect for corrosion or separation.
GLASS
ASSEMBLY
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
Figure 4.1 Fixed Glass Assembly
Surrounds, Decorative Fronts
Frequency: Annually
By: Homeowner
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Inspect for scratches, dents or other damage and repair
as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
Remote Control
Frequency: Seasonally
By: Homeowner
Tools needed: Replacement batteries and remote control instructions.
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
• Place batteries as needed in remote transmitters and
battery-powered receivers.
• Place remote control out of reach of children.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
• Remove batteries from remote controls.
• Unplug 3 volt adapter plug on IPI models.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
15
C. Maintenance Tasks - Qualified Service
Technician
• Remove all foreign objects.
The following tasks must be performed by a qualified service technician.
Burner Ignition and Operation
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Verify unobstructed air circulation.
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Inspect gasket seal and its condition.
• Verify burner is properly secured and aligned with pilot
or igniter.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Verify batteries have been removed from battery back-up
IPI systems to prevent premature battery failure or
leaking.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Inspect for lifting or other flame problems.
Logs/Lava Rock
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as necessary. Refer to Installation manual for log/lava rock placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
• Verify correct lava rock placement. No lava rock on
burner.
WARNING! Risk of Explosion! DO NOT place lava rock
on burner top. Improperly placed lava rock interferes with
proper burner operation.
Firebox
Frequency: Annually
• Verify air shutter setting is correct. See Installation
Manual for required air shutter setting. Verify air shutter
is clear of dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 4.2
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Inspect IPI flame sensing rod for soot, corrosion and
deterioration. Polish with fine steel wool or replace as
required.
• Verify that there is not a short in flame sense circuit
by checking continuity between pilot hood and flame
sensing rod. Replace pilot as necessary.
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
16
Figure 4.2 IPI Pilot Flame Patterns
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
5
Frequently Asked Questions and Troubleshooting
A. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the fireplace warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the fireplace is allowed to burn for 20 to 40 minutes.
Odor from fireplace
When first operated, this fireplace may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the fireplace.
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Film on the glass
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the fireplace.
Is it normal to see the pilot flame burn
continually?
In an intermittent pilot ignition system (IPI), the pilot flame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot flame to
remain lit.
Lava Rock/Optional Rock Media Kit
There may be some “cracking” noise coming from the fireplace during the first few heating
and cooling cycles. This noise is associated with settling rock and some minor cracking of
larger pieces of rock. This will lessen over time as the glass rock is conditioned to the heating and cooling temperature changes.
It is expected that a few small pieces (approximately 10 pieces) of rock may fall through the
base pan and come to rest on the fireplace bottom. This has no affect on fireplace performance.
Power Outages
(battery backup)
This appliance can operated on battery power in the event of a power outage. To access
the battery pack, the decorative front, mesh and glass assembly must be removed. Refer to
Section 3 for more details.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
17
B. Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
Intellifire Ignition System
Symptom
Possible Cause
1. Pilot won’t light.
A. Incorrect wiring.
The ignitor/module
makes noise, but no
B. Loose connections or electrical
spark.
shorts in the wiring.
2. Pilot won’t light,
there is no noise or
spark.
3. Pilot sparks, but
Pilot will not light.
18
Corrective Action
Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor are
connected to correct terminals on module and pilot assembly.
Verify no loose connections or electrical shorts in wiring from module to pilot assembly. Verify connections underneath pilot assembly are tight; also verify connections are not grounding out to metal
chassis, pilot burner, pilot enclosure, mesh screen if present, or any
other metal object.
C. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .095 in. (2.41 mm) to .135 in. (3.43 mm).
D. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place a grounded wire about 3/16 in. (5
mm) away from “I” terminal on module. Place ON/OFF rocker switch
or wall switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode. Replace pilot if necessary.
A. No power or transformer installed
incorrectly.
Verify that transformer is installed and plugged into module. Check
voltage of transformer under load at spade connection on module
with ON/OFF switch in ON position. Acceptable readings of a good
transformer are between 3.2 and 2.8 volts AC.
B. A shorted or loose connection in
wiring configuration or wiring harness.
Remove and reinstall the wiring harness that plugs into module.
Verify there is a tight fit. Verify pilot assembly wiring to module. Remove and verify continuity of each wire in wiring harness. Replace
any damaged components.
C. Improper wall switch wiring.
Verify that 110-120 VAC power is “ON” to junction box.
D. Module not grounded.
Verify black ground wire from module wire harness is grounded to
metal chassis of appliance.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position. Remove
ignitor wire “I” from module. Place ON/OFF rocker switch or wall
switch in ON position. If there is no spark at “I” terminal module
must be replaced. If there is a spark at “I” terminal, module is fine.
Inspect pilot assembly for shorted sparker wire or cracked insulator
around electrode.
A. Gas supply.
Verify that incoming gas line ball valve is “open”. Verify that inlet
pressure reading is within acceptable limits.
B. Ignitor gap is too large.
Verify gap of igniter to right side of pilot hood. The gap should be
approximately .095 in. (2.41 mm) to .135 in. (3.43 mm).
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance.
D. Module voltage output / Valve/Pilot
solenoid ohms readings.
Verify battery voltage is at least 2.7 volts. Replace batteries if voltage is below 2.7.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Intellifire Ignition System - (continued)
Symptom
4. Pilot lights but continues to spark, and main
burner will not ignite.
(If the pilot continues
to spark after the
pilot flame has been lit,
flame rectification has
not occurred.)
Possible Cause
A. A shorted or loose connection in flame
sensing rod.
Corrective Action
Verify all connections to wiring diagram in manual. Verify
connections underneath pilot assembly are tight. Verify connections are not grounding out to metal chassis, pilot burner, pilot enclosure or screen if present, or any other metal
object.
B. Poor flame rectification or contaminated With fixed glass assembly in place, verify that flame is enflame sensing rod.
gulfing flame sensing rod on left side of pilot hood. Flame
sensing rod should glow shortly after ignition. Verify correct pilot orifice is installed and gas inlet is set to pressure
specifications. Polish flame sensing rod with fine steel wool
to remove any contaminants that may have accumulated on
flame sensing rod.
C. Module is not grounded.
Verify module is securely grounded to metal chassis of appliance. Verify that wire harness is firmly connected to the
module.
D. Damaged pilot assembly or contaminated flame sensing rod.
Verify that ceramic insulator around the flame sensing rod
is not cracked, damaged, or loose. Verify connection from
flame sensing rod to white sensor wire. Polish flame sensing rod with fine steel wool to remove any contaminants
that may have accumulated on flame sensing rod. Verify
continuity with a multimeter with ohms set at lowest range.
Replace pilot if any damage is detected.
E. Module.
Turn ON/OFF rocker switch or wall switch to OFF position.
Remove ignitor wire “I” from module. Place ON/OFF rocker
switch or wall switch in ON position. If there is no spark at “I”
terminal module must be replaced. If there is a spark at “I”
terminal, module is fine.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
19
6
Reference Materials
A. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Remote Controls, Wall Controls and Wall
Switches
After a qualified service technician has installed the remote control or wall switch, follow the instructions supplied with the control installed to operate your fireplace:
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
Optional Fan
If an optional fan is purchased, have it installed by a
qualified service technician. Section 3 discusses using
the fan to manage the heat output. Follow the instructions supplied with the fan kit to operate your fan.
See your dealer if you have questions.
Optional Media Kit
Media Kits are available for use with the SL-5F and SL7F models. Install media according to the instructions
included with the kit.
WARNING! Choking Hazard! Keep media out of reach
of children.
20
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
SL-5F
B. Service
Parts
Service
Parts
Fusion 32” Gas Fireplace - DV
Beginning Manufacturing Date: Dec 2016
Ending Manufacturing Date: Active
Log Set Assembly
14
6
7
12
10
11
8
9
13
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.
Hearth and Home Technologies does not sell directly to consumers. Provide model
Stocked
at Depot
number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
Log Set Assembly
LOGS-550F
1
Log 1
SRV2297-700
2
Log 2
SRV2033-709
3
Log 3
SRV2033-708
4
Log 4
SRV2033-721
5
Log 5
6
Burner NG, LP
2297-105
7
Burner Leg
2297-103
8
Valve Assembly
9
Base Pan
2297-017
10
Glass Door Assembly
GLA-550TR
11
Firescreen Front
FS-5-BK
12
Hood
2115-230
13
Junction Box
4021-013
14
Elbow Heat Shield
385-290
Qty 2 req
Y
SRV2033-720
Y
See following page
Additional service part numbers appear on following page.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Y
Y
12/16
21
SL-7F
Service Parts
Beginning Manufacturing Date: Dec 2016
Ending Manufacturing Date: Active
Fusion 36” Gas Fireplace - DV
Log Set Assembly
13
5
6
9
11
10
8
7
12
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.
Hearth and Home Technologies does not sell directly to consumers. Provide model
Stocked
at Depot
number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
Log Set Assembly
LOGS-750F
1
Log 1
SRV2298-700
2
Log 2
3
Log 3
4
Log 4
5
Burner NG, LP
6
Burner Leg
7
Valve Assembly
8
Base pan
2298-017
9
Glass Door Assembly
GLA-750TR
Y
10
Firescreen Front
FS-7-BK
Y
11
Hood
2118-230
12
Junction Box
4021-013
13
Elbow Heat Shield
385-290
Qty 2 req
SRV2033-709
SRV2033-721
Qty 2 req
SRV2033-720
2298-105
Y
2297-103
See following page
Additional service part numbers appear on following page.
22
Y
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
Y
12/16
SL-5F, SL-7F
Service Parts
Beginning Manufacturing Date: Dec 2016
Ending Manufacturing Date: Active
8.3
#8 Valve Assembly
8.4
8.2
8.1
8.5
8.6
8.8
8.7
8.14 8.13
8.9
8.10
8.11
8.12
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.
Hearth and Home Technologies does not sell directly to consumers. Provide model
Stocked
at Depot
number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
8.1
Shutter Bracket Assembly
2118-121
8.2
Pilot Bracket
2297-112
8.3
3-Hole Grommet
2118-420
Pilot Assembly NG
2106-169
Y
Pilot Assembly LP
2106-170
Y
SRV485-301
Y
Y
8.4
Pilot Tube
Y
8.5
Flex Ball Valve Assembly
302-320A
8.6
Valve Bracket
2118-104
Valve NG
750-500
Y
Valve LP
750-501
Y
8.7
8.8
Battery Pack
8.9
Male Connector
8.10
593-594A
Y
303-315/5
Y
Thermostat Wire Assembly
2118-170
Y
8.11
Module
593-592
Y
8.12
Module Wire Assembly
593-590A
Y
8.13
3 Volt Transformer
593-593A
Y
8.14
Flexible Gas Connector
7000-156
Y
Male-Male 2” Jumper Wires
2012-206
Y
582-845
Y
Pkg of 5
Ori¿ce NG (#45)
SL--5F
Ori¿ce LP (1.25 mm)
Ori¿ce NG (#42)
SL--7F
Ori¿ce LP (#54)
582-8125
Y
582-842
Y
582-854
Y
Additional service part numbers appear on following page.
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
23
SL-5F, SL-7F
Service Parts
Beginning Manufacturing Date: Dec 2016
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.
Hearth and Home Technologies does not sell directly to consumers. Provide model
Stocked
at Depot
number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
Bottom Panel
COMMENTS
PART NUMBER
SL-5F
2297-106
SL-7F
2298-106
Exhaust BafÀe
550-155
Exhaust Restrictor
530-299
Gasket Assembly
SL-5F
2115-080
SL-7F
2118-080
Contains Burner neck, shutter bracket, vent, seal cap, valve plate, and air passage gaskets
Glass Latch Assembly
Pkg of 2
Heat Shield, Junction Box
2372-127
Heat Shield, Header
2118-120
Rock Placement Jig
Y
4021-297
Lava Rock
SL-5F
2297-113
SL-7F
2298-113
Touch Up Paint
TUP-GBK-12
Valve Plate Cover
2188-101
NGK-550F
Y
LPK-550F
Y
NGK-750F
Y
LPK-750F
Y
Pilot Ori¿ce NG
593-528
Y
Pilot Ori¿ce LP
593-527
Y
Regulator NG
NGK-DXV
Y
Regulator LP
LPK-DXV
Y
Conversion Kit NG
Conversion Kit LP
Conversion Kit NG
Conversion Kit LP
24
2382-400/2
SL-5F
SL-7F
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
C. Contact Information
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
Please contact your Heat & Glo dealer with any questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5613487, 5647340, 5890485,
5941237, 6006743, 6019099, 6053165, 6145502, 6374822, 6484712, 6601579, 6769426, 6863064, 7077122, 7098269,
7258116, 7470729, 8147240 or other U.S. and foreign patents pending.
2000-945C
Printed in U.S.A. - Copyright 2016
Heat & Glo • SL-5F, SL-7F Owner’s Manual • 2499-981 Rev. C • 12/16
25
Download PDF