Leggere attentamente queste istruzioni d’uso prima di
utilizzare la macchina
ITALIANO
ISTRUZIONI PER L’USO
BEDIENUNGSANLEITUNG
Bedienungsanleitung ist vor dem ersten Gebrauch der
Maschine aufmerksam zu lesen
MODE D’EMPLOI
DEUTSCH
Read these operating instructions carefully before
using the machine
ENGLISH
OPERATING INSTRUCTIONS
GEBRUIKSAANWIJZING
Lees deze INSTRUCTIES aandachtig door, alvorens
het apparaat te gebruiken
TYPE SUP021 YBDR
FOR HOUSEHOLD USE ONLY
ESPAGÑOL
PORTUGUÊS
INSTRUÇÕES PARA USO
Ler atentamente estas instruções de uso antes de
utilizar a máquina
NEDERLAND
INSTRUCCIONES DE USO
Diese Leer atentamente estas instrucciones de uso
antes de utilizar la máquina
FRANÇAIS
Lire attentivement ce mode d’emploi avant d’utiliser
la machine
22
IMPORTANT SAFEGUARDS
CAUTION
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons, including
the following:
1 Read all instructions and information in this instruction book and any other
literature included in this carton referring to this product before operating or using
this appliance.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against fire, electric shock and personal injury do not immerse cord,
plugs or appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6 Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any way. Return appliance to the nearest
authorized service centre for examination, repair or adjustment.
7 The use of accessory attachments not recommended by the appliance manufacturer
may result in fire, electric shock or personal injury.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter, or touch hot surfaces.
10 Do not place on or near a hot gas or electric burner, or in a heated oven.
11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect,
turn switch to “OFF”, then remove plug from wall outlet.
12 Do not use appliance for other than intended household use.
13 Use extreme caution when using hot steam.
This appliance is for household use. Any servicing, other than cleaning and user
maintenance, should be performed by an authorized service centre. Do not immerse
base in water. To reduce the risk of fire or electric shock, do not disassemble the base.
There are no user serviceable parts inside. Repair should be done by authorized service
personnel only.
SAVE THESE INSTRUCTIONS
1 Check voltage to be sure that the voltage indicated on the nameplate agrees with
your voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during
operation.
4 Never clean with scouring powders or hard implements. Simply use a soft cloth
dampened with water.
5 To avoid your coffee maker scaling up, use purified or bottled water.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of getting tangled up or
tripping over a longer cord.
B Longer extension cords are available and may be used if care is exercised in their use.
C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance.
2 if the appliance is of the grounded type, the extension cord should be a
grounding type
3 the cable does not hang from the table to avoid the risk of getting caught up in it.
23
This coffee machine is ideal for preparing espresso coffee either with coffee beans
or preground coffee and also features a device for dispensing steam and hot water.
This elegantly styled machine is designed for household use only. It is not suitable
for continuous professional-type use.
TECHNICAL SPECIFICATIONS
• Voltage rating
See rating plate on appliance
• Power rating
See rating plate on appliance
• Casing material
Metal
• Size (w x h x d) (mm)
285 x 375 x 400
• Weight (Kg)
11
• Cord length (mm)
1200
• Control panel
Front (Digital)
• Water tank (lit.)
2 - Extractible
• Power supply
See rating plate on appliance
• Pump pressure (bars)
15
• Boiler
2 - Stainless steel
• Coffee container capacity (g.)
300 of coffee beans
TO FACILITATE INTERPRETATION
• Rapid Steam
Steam ready in a few seconds
A warning triangle draws attention to the instructions that are important for user safety. Please carefully abide by these instructions to
avoid serious injury!
• Grinders
Ceramic
• Quantity of ground coffee
6 - 10 g
• Dreg drawer capacity
13
• Safety devices
Boiler pressure safety valve
safety thermostat
Warning. The manufacturer shall accept no liability for damage or injury
caused by:
• improper use or use for other than the intended purposes;
• repairs carried out by anyone other than an authorised service centre;
• tampering with the power cord;
• tampering with any machine component;
• use of spare parts and accessories other than those supplied by the
manufacturer.
The warranty will be invalidated in such cases.
HOW TO USE THESE OPERATING INSTRUCTIONS
Keep these operating instructions in a safe place and make them available to
anyone else who should use the coffee machine. For further information or an
explanation of problems not completely or sufficiently addressed in these instructions, contact an authorised service centre.
Subject to engineering and manufacturing changes as warranted by technological
developments.
Machine in conformity with European Directive 89/336/EEC (Italian Legislative
Decree 476 of 04/12/92) concerning electromagnetic compatibility.
ENGLISH
GENERAL INFORMATION
24
SAFETY RULES
IN THE EVENT OF AN EMERGENCY
- Do not use the power cord to carry or pull the coffee machine.
Immediately unplug the appliance.
HAZARDS
THE APPLIANCE MAY ONLY BE USED
- The appliance must not be used by children or by individuals unacquainted with
the operating instructions.
- The appliance is dangerous for children. If left unattended it must be
switched off.
- Do not leave the materials used to pack the appliance within children’s reach.
- Do not direct a jet of hot steam and/or hot water toward yourself or others:
danger of scalding.
- Do not introduce any objects through the openings in the appliance (Electrical
hazard!).
- Do not touch the plug when your hands or feet are wet. Do not unplug the
appliance by yanking at the power cord.
- Warning: contact with hot water, steam or and hot water/steam nozzle may
cause burns.
- In a closed place.
- To prepare coffee, dispense hot water, froth milk or heat beverages using
steam.
- For household use.
- By adults in full possession of their physical and mental capacities.
NEVER USE THE APPLIANCE
for purposes other than those indicated above to avoid hazards. Never place
any substances in the containers other than those specified in the instruction
manual. When you fill a container, make sure all nearby containers are closed.
Fill the water tank only with fresh drinking water: hot water and/or other liquids
may damage the machine. Do not use carbonated water. The coffee grinder may
be adjusted only while it is running. Do not introduce your fingers or any material
other than coffee beans into the coffee grinder. Before attempting to access the
inside of the coffee grinder, switch OFF the machine and remove the plug from
the electric socket. Do not put coffee beans or instant coffee into the ground coffee
container.
MAINS CONNECTION
Connect the coffee machine to a suitable electric socket. The voltage must match
the voltage specified on the appliance rating plate.
INSTALLATION
- Choose a perfectly level supporting surface. Do not place on a hot surface!
- Maintain a distance of 10 cm from walls and electric or gas burners.
- Do not keep at temperatures below 0 °C; the appliance may be damaged by
freezing.
- The electric socket must be accessible at all times.
- The power cord must not be damaged, secured with clamps, placed on very hot
surfaces etc.
- Do not let the power cord hang loosely (Warning: danger of tripping or of causing
the appliance to fall).
- Should the power cable be damaged, it must be replaced by the manufacturer
or his customer service department.
FAULTS
- Do not use the appliance if it malfunctions or you suspect damage, e.g.
after a fall.
- Repairs must be performed by an authorised service centre.
- Do not use an appliance with a defective power cord. The cord may be replaced
exclusively by a service centre (Electrical hazard!).
- Switch off the appliance before opening the service door. Danger of burns!
CLEANING / DESCALING
- Before cleaning the appliance, unplug it and allow it to cool down.
- Avoid exposing the appliance to splashes of water. Do not immerge it in water.
- Do not dry machine components in a conventional or microwave oven.
SPARE PARTS
To guarantee safety, you should use only original spare parts and accessories.
DISPOSAL
- The packing materials can be recycled.
- Appliance: unplug the appliance and cut the power cord.
- Deliver the appliance and power cord to a service centre or public waste
disposal facility.
COMPONENT DESCRIPTION
Coffee bean container lid
Coffee bean container
Cup heater plate
Grind adjustment knob
Coffe container opening
button
Water tank
Control panel
Steam knob
Cleaning
brush
Brew group key
Water hardness
test
Preground
coffee measure
Cartridge filter
applicator
“Aqua Prima”
cartridge filter
Service door
SBS
ON/OFF switch
Height and depth
adjustable brew unit
Hot water/
steam tube
Drip tray + grill
Tray full indicator
LCD Display
Brew group
Swivel base
Coffee button
Small coffee button
Large coffee button
Preground coffee selector button
“ESC” in programming mode
Hot water selector button
“Page up” in programming mode
Programming “MENU” selector button
“OK” in programming mode
Descaling button
“Page down” in programming mode
ENGLISH
Water tank lid
Preground coffee
dispenser lid
Dregs drawer
25
26
INSTALLATION / VENTILATE
The messages displayed by the machine during operation are shown
on page 40.
Important warning for using the “Aqua Prima Filter” can be found at
page 40.
See rating plate
Fill the coffee bean container
with coffee beans.
The “Aqua Prima” filter can
be installed (see pg.31).
Fill the tank with fresh drinking water.
Insert the plug into a suitable electric socket.
HOT WATER
VENTILATE
A message is displayed
indicating that the machine
circuit needs loading.
Place a container beneath
the steam tube.
Turn the knob counterclockwise to start loading the
circuit.
SELECT PRODUCT
READY FOR USE
Turn the knob clockwise
to terminate the circuitloading process.
Move the ON/OFF switch to
“I” to turn on the machine.
Remove the container.
The machine is ready for
use.
Wait until a steady stream
of water flows out from the
nozzle.
A message is displayed
indicating that the machine
circuit has been loaded.
Note: You must load the circuit before starting up the
machine for the first time, if it has been inoperative for a
lengthy period or if the water tank has been completely
emptied. Moreover, the circuit must be loaded every
time the message “VENTILATE” is displayed.
Coffee flows out more
quickly. Press and turn.
ADJUSTMENT
Coffee dose adjustment - You must adjust the dose before dispensing coffee (See “Programming”).
This adjustment will have an immediate effect on the coffee brewed.
AROMA SMALL COFFEE *
AROMA COFFEE
For adjusting the quantity
of a small coffee.
AROMA COFFEE
*
AROMA LARGE COFFEE
For adjusting the quantity
of a medium coffee.
AROMA LARGE COFFEE *
PREBREWING
For adjusting the quantity
of a large coffee.
BIG CUPS
To place the brew unit again in its position, pull it until it fits in.
To use big cups, press the button and push the brew unit until
the end.
COFFEE IN CUPS
To adjust the quantity of coffee dispensed to the size of your cups.
Place a cup beneath
the brew unit, press the
1 COFFEE
button corresponding
PROGR. QUANTITY
to the type of coffee
Or
desired and keep it
pressed while coffee
is being dispensed.
SBS
COFFEE IN CUPS
For machines provided with SBS only. - To adjust the strength and consistency of brewed coffee.
The adjustment can also be made while brewing the coffe. This adjustment will have an immediate
effect on the coffee brewed.
If you set the grinder on too fine a grind (knob turned all the way
anticlockwise) and the SBS control on “strong” (toward the right), coffee
may flow out in a slow trickle or not at all.
BIG CUPS
Coffee flows out more
slowly. Press and turn.
Café crème.
Espresso coffee.
Strong black coffee.
When the cup has
filled to the desired level, release the button; the machine is now
programmed to dispense the quantity of coffee you have chosen.
ENGLISH
Use coffee bean blends for espresso coffee makers. If you do not obtain
the desired result, try using different coffee blends. Store coffee in a cool
place, in a hermetically sealed container.
You will note a change after dispensing 1 - 2 coffees.
The fineness of the grind may be
adjusted using the knob.
COFFEE DOSE
27
Adjustment may be made only while the coffee grinder is
operating.
ADJUSTMENT
COFFEE GRINDER
ADJUSTMENTS
DISPENSING COFFEE / HOT WATER
COFFEE BEANS
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
SELECT PRODUCT
READY FOR USE
1 SMALL COFFEE
Or
PREGROUND COFFEE
Make sure that the machine is ready.
Position a warm coffee
cup or cups beneath the
brew unit.
Press the button of the
type of coffee desired.
Once for 1 coffee.
SELECT PRODUCT
PREGROUND COFFEE
Position a warm coffee cup
beneath the brew unit.
Select the product “Preground coffee”.
HOT WATER
READY FOR USE
HOT WATER
28
Place a container beneath
the steam tube.
Press the button to dispense water.
2 SMALL COFFEES
Or
Twice for 2 coffees.
When the machine stops
making the coffee, remove
the cup or cups.
1 SMALL COFFEE
PREGROUND COFFEE
Or
Introduce ground coffee
using the coffee measure.
MAX 1 MEASURE
Press the button of the
type of coffee desired.
HOT WATER
Turn the knob counterclockwise to start dispensing. Close the knob when
finished.
When the machine stops
making the coffee, remove
the cup.
SELECT PRODUCT
READY FOR USE
Remove the container.
Press the button to restore
the machine to normal
operation.
STEAM / CAPPUCCINO
29
ENGLISH
CAPPUCCINO
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
Fill a cup to 1/3 with cold
milk.
Place a container beneath
the steam tube. Open the
knob to discharge any
residual water.
When only steam comes
out, close the knob.
Remove the container.
Position the cup containing
milk beneath the steam
tube.
Open the knob to release
steam.
STEAM
The machine will signal the
function.
Move the cup in a circular
fashion to heat the milk
evenly.
After frothing the milk,
close the knob.
Dispense coffee into the
cup to prepare a delicious
cappuccino.
SELECT PRODUCT
READY FOR USE
STEAM
STEAM
Remove the cup and
position it beneath the
brew unit.
Open the knob to
discharge any residual
water. Close the knob.
Place the cup beneath the
steam tube.
Open the knob.
Heat by moving in circles.
Close the knob.
Remove the container.
DESCALING
Warning! Never use vinegar as a descaling agent. You can use any
commercially available non-toxic, non-harmful descaling product for coffee
machines. We recommend using a Saeco descaling agent.
Descaling is necessary every 3-4 months, when there is a reduction in the water
capacity. The machine must be on; it automatically controls the distribution of the
descaling solution.
DESCALING
READY FOR USE
MACHINE IS DESCALING
DESCALING
OPEN KNOB
When the machine gives
the signal, press the button
x 5 seconds.
Remove the cartridge
filter.
Fill the water tank with the Place a large receptacle Turn the knob to open the The machine will start
descaling.
descaling solution.
valve.
beneath the steam tube.
RINSE MACHINE
FILL WATERTANK
RINSE MACHINE
PRESS KEY
MACHINE IS RINSING
DESCALING FINISHED
CLOSE KNOB
When the descaling cycle
is completed, close the
knob.
INTERRUPTION
30
Rinse out the tank and fill it with fresh drinking water.
DESCAL. INTERRUPTED
EMPTY WATERTANK
Press the button to confirm
the rinse cycle.
Open the knob.
The machine will start
rinsing.
RINSE MACHINE
PRESS KEY
When the rinse cycle is
completed, close the knob
and load the circuit.
If the descaling cycle is interrupted
by switching off the machine, it will
automatically resume when the machine is
switched back on.
When descaling is over, fit the cartridge
filter back in place.
MACHINE IS DESCALING
OPEN KNOB
The descaling cycle can
be cut short by closing the
knob.
RINSING FINISHED
CLOSE KNOB
Press the button.
Rinse out the tank and fill it Press the button to confirm
with fresh drinking water. the rinse cycle and proceed
normally.
“AQUA PRIMA” CARTRIDGE FILTER
Before descaling, remove the filter from the tank.
ENGLISH
INSTALLATION
The filter must be replaced when signalled by the machine.
See “Programming”.
31
Remove the filter from the
packing container.
Adjust the dater to the
current month.
Insert the applicator and
turn it clockwise to secure
it to the filter.
Check where the filter
positioning and reference
mark is.
Put the filter into the empty
tank.
The reference must be
positioned in correspondence with the groove.
HOT WATER
READY FOR USE
Press until the end limit.
Turn the applicator counter-clockwise and remove
it from the tank.
Fill the tank with fresh
drinkable water.
Position a container
beneath the steam tube
and turn the machine on.
WATERFILTER
ON
Open the knob
dispense water.
and
Empty the water tank out at
intervals.
When the tank is empty, fill
it again with fresh drinkable
water.
See “Programming”. Enable
the filter control function and
reset the water counter.
Press the button
dispense water.
to
It is possible to use the
machine without filter,
Saeco suggests its use.
If filter is not used, the
machine must be descaled
more frequently.
You can now use your
coffee machine.
CLEANING AND MAINTENANCE
Do not dry the machine and/or its components in a microwave and/or
conventional oven.
Do not immerge the machine in water and do not place any of its
components in a dishwasher.
BASIC
CLEANING
Turn the machine off.
Unplug the machine.
Wash the water tank.
Wash the filter inside it.
Remove the drip tray, empty it out and wash it.
Remove the dregs drawer,
empty it out and wash it.
The machine, its components
and the brew unit must be
cleaned at least once a week.
Use the brush to clean the
ground coffee dispenser.
Remove the brew unit
and wash it with water.
Press the PUSH button to
release the brew group.
Unscrew the upper filter
and wash it.
Unscrew and clean the
“pannarello” attachment.
BREW GROUP
32
Remove the grill. Open
the front door. Remove the
drawers.
Fit the filter back in place
when clean.
Wash the unit, dry it and
fit it back in place. Do not
press the “PUSH” button.
Set all machine components
back in position.
Close the door.
PROGRAMMING MACHINE FUNCTIONS
33
ENERGY SAVING
RINSING
*
Press the “MENU” button
to access the programming
mode.
ENERGY
SAVING
RINSING
LANGUAGE
*
RINSING
LANGUAGE
*
Use the “∧” and “∨”
buttons to display/change
the menus.
When the appliance is used infrequently, it can be switched
to the STANDBY mode.
With this function you can cut energy costs.
Using the “OK” button you can
select the menu item marked
with an - -
When this function is enabled, the internal machine circuits
will be rinsed immediately after the warming-up phase to
ensure that coffee is prepared with fresh water only.
In all new appliances this function has already been enabled
in the factory.
Press ESC to exit without
making any changes.
*
ENERGY SAVING
RINSING
*
When the function appears, select it using the
“OK” button.
RINSING
RINSING
ON
RINSING
ON
ENGLISH
PROGRAMMING
START
The user can change some machine operating parameters to suit his/her personal needs.
RINSING
LANGUAGE
*
When the function appears, select it using the
“OK” button.
ENERGY SAVING
The display will show
that the machine is in the
standby mode.
RINSING
OFF
From this menu you can
disable the function.
Use the “OK” button to
select a menu or confirm
a change.
SELECT PRODUCT
READY FOR USE
Press the “OK” button to
restore the machine to
normal operation.
RINSING
ON
Press the “OK” button to
confirm your choice.
LANGUAGE
PROGRAMMING MACHINE FUNCTIONS
This function allows you to change the display language.
You can choose among Italian, German, Portuguese,
Spanish, English, French, Dutch, Polish and Swedish. The
appliance is usually programmed on the language of the
country in which it is sold.
LANGUAGE
WATER HARDNESS
*
WATER
HARDNESS
When the function appears, select it using the
“OK” button.
This function must be activated when the “Aqua Prima”
cartridge filter is installed for the first time.
The “RESET” command must be activated every time a new
cartridge filter is installed.
This function enables optimal management of the “Aqua
Prima” filter as it warns the user when the filter needs
replacing.
LANGUAGE
ENGLISH
Dip the strip in water for 1
second.
Check how many squares
change colour.
WATERFILTER
CUP HEATER
*
When the function appears, select it using the
“OK” button.
LANGUE
FRANCAIS
Select the desired language.
WATER HARDNESS
WATERFILTER
The hardness of tap water may vary depending on the
region. For this reason, the appliance can be set according
to the water hardness in the place where it is to be used,
expressed on a scale of 1 to 4.
The appliance is factory set on a hardness value of 3. The
setting should be adjusted according to the level of water
hardness in the local area.
WATER FILTER
34
*
When the function appears,
select it using the “OK”
button.
WATERFILTER
ON
From the menu it is possible
to set the function to ON.
Press the “OK” button to
confirm your choice.
WATER HARDNESS
HARDNESS 2
Select the corresponding hardness
(e.g. 2 squares = Hardness 2) and
memorize the value by pressing
the “OK” button.
WATERFILTER
RESET
Press the “OK” button to
confirm your choice.
CUP HEATER
TEMPERATURE
*
TEMPERATURE
CUP HEATER
OFF
This function allows you to turn on the cup heater present in
the machine cover.
When the function appears, select it using the
“OK” button.
To meet individual needs, from this menu it is possible
to adjust the coffee temperature; it is possible to choose:
“low” - “medium” - “high”.
TEMPERATURE
*
AROMA SMALL COFFEE
When the function appears, select it using the
“OK” button.
AROMA SMALL
COFFEE
CUP HEATER
ON
35
ENGLISH
CUP HEATER
PROGRAMMING MACHINE FUNCTIONS
AROMA SMALL COFFEE *
AROMA COFFEE
Choose whether you wish
to turn the cup heater plate
on or off.
TEMPERATURE
MEDIUM
Press the “OK” button to
confirm your choice.
TEMPERATURE
HIGH
Select the desired temperature.
Press the “OK” button to
confirm your choice.
AROMA SMALL COFFEE
NORMAL
AROMA SMALL COFFEE
STRONG
Select the desired quantity
of coffee.
Press the “OK” button to
confirm your choice.
For setting, when the machine is switched on, the quantity
of coffee to be ground in order to brew the small coffee.
When the function appears, select it using the
“OK” button.
AROMA
COFFEE
PROGRAMMING MACHINE FUNCTIONS
AROMA COFFEE
*
AROMA LARGE COFFEE
AROMA
LARGE COFFEE
AROMA COFFEE
NORMAL
AROMA COFFEE
STRONG
For setting, when the machine is switched on, the quantity
of coffee to be ground in order to brew the coffee.
When the function appears, select it using the
“OK” button.
AROMA LARGE COFFEE *
PREBREWING
Select the desired quantity
of coffee.
AROMA LARGE COFFEE
NORMAL
Press the “OK” button to
confirm your choice.
AROMA LARGE COFFEE
STRONG
For setting, when the machine is switched on, the quantity
of coffee to be ground in order to brew the large coffee.
When the function appears, select it using the
“OK” button.
PREBREWING
36
With the pre-brewing process the coffee is slightly moistened
before actual brewing. This brings out the full aroma of the
coffee and lends it an excellent flavour. It is possible to
choose either “enabled”, or “disabled”, or “long”.
PREBREWING
TOTAL COFFEES
*
When the function appears, select it using the
“OK” button.
Select the desired quantity
of coffee.
PREBREWING
ON
Choose whether you wish
to turn the pre-brewing
function on or off.
Press the “OK” button to
confirm your choice.
PREBREWING
LONG
Press the “OK” button to
confirm your choice.
TOTAL COFFEES
TIMER
*
TIMER
CLOCK
TIMER
2
TOTAL COFFEES
2
This function enables the user to see how many coffees the
machine has already dispensed.
When the function appears, select it using the
“OK” button.
*
The display will show the
number of coffees the
machine has dispensed.
STANDBY
AFTER
3:00
Press “ESC” to exit the
menu.
STANDBY
AFTER
1:15
This is a factory-set function that automatically switches the
machine into “Standby” when 3 hours have elapsed since a
coffee was dispensed.
The switch-off time can be adjusted, in 15-minute intervals,
to a minimum of 15 minutes; the function cannot be
deactivated.
RINSING
CYCLE
TOTAL COFFEES
This function is used to rinse all the coffee-dispensing parts
with water.
Fill the tank with fresh drinking water.
The rinsing cycle cannot be interrupted.
A person must be present during this operation.
Warning: a large quantity of water may be discharged from the
coffee brew unit. Before starting, empty out the drip tray and
keep an additional container handy.
37
ENGLISH
TOTAL
COFFEE
PROGRAMMING MACHINE FUNCTIONS
When the function appears, select it using the
“OK” button.
RINSING CYCLE
FACTORY SETTINGS
*
When the function appears, select it using the
“OK” button.
Use the buttons to adjust
the timer setting.
RINSING CYCLE
The machine will carry out
a rinsing cycle.
Press the “OK” button to
confirm your choice.
FILL WATERTANK
When the cycle is
completed this message
will be displayed:
PROGRAMMING MACHINE FUNCTIONS
CLOCK
38
This function may be activated and deactivated by the
user to:
- display the current time when the machine is in the
“ENERGY SAVING” or “SELECT PRODUCT” mode
- program the machine to switch on and off at a specific
time.
CLOCK
RINSING CYCLE
*
When the function appears, select it using the
“OK” button.
SHOW CLOCK TIME
CLOCK
*
Select using the “∧” and
“∨” buttons and press “OK”
to show the clock time.
ON/OFF TIME
OFF
0:00
Set the time you want the
machine to turn off.
SHOW CLOCK TIME
OFF
SHOW CLOCK TIME
ON
If this option is selected,
the clock time will be
shown on the display.
CLOCK
CLOCK TIME
*
Menu for switching clock
function on or off.
If this option is selected,
the clock time will NOT be
shown on the display.
CLOCK
ON
This option activates the
clock function.
CLOCK TIME
ON/OFF TIME
*
Select using the “∧” and
“∨” buttons and press “OK”
to activate the clock setting
procedure.
ON/OFF TIME
SHOW CLOCK TIME
*
Menu for programming
machine ON/OFF times.
CLOCK
OFF
This option deactivates the
clock function.
CLOCK TIME
0:00
Set the hour using the “∧”
and “∨” buttons and press
“OK”: Set the minutes using
the “∧” and “∨” buttons and
press “OK”.
ON/OFF TIME
ON
0:00
Set the time you want the
machine to turn on.
ENERGY SAVING
This appears when the
machine time settings are
OFF. Press “OK” to activate.
With this function you can restore the machine operating
parameters originally set by the manufacturer. If you restore
all the factory settings, all customized settings will be lost.
FACTORY SETTINGS
ENERGY SAVING
*
FACTORY SETTINGS
NO
39
FACTORY SETTINGS
YES
ENGLISH
FACTORY
SETTINGS
PROGRAMMING MACHINE FUNCTIONS
When the function appears, select it using the
“OK” button.
Choose whether to restore
the initial factory settings.
Press the “OK” button to
confirm your choice:
40
DISPLAY MESSAGES - NOTES ON THE AQUA PRIMA CARTRIDGE FILTER
Messages are displayed to guide users and help them to use the machine correctly.
ENERGY SAVING
Press “MENU/OK”.
RINSING
WARMING UP ...
DESCALING
READY FOR USE
Descale the machine.
REPLACE WATERFILTER
READY FOR USE
FILL WATERTANK
Fill the water tank with fresh drinking water.
COFFEE BEANS EMPTY
The machine is in the heating phase; wait until the machine has finished this operation.
Replace the “Aqua Prima” filter as soon as possible;
should not a new filter be available, remove the existing
one, and deactivate the “Water Filter” function (See Programming).
Fill the coffee bean container and start the coffee
dispensing cycle.
Open the door, remove the dregs drawer and empty the
used coffee grinds into a suitable container.
ADDITIONAL INFORMATION FOR CORRECTLY USING THE “AQUA PRIMA”
FILTER.
Important note: the dregs drawer may be emptied only when the machine is
on. The drawer must be removed for at least 5 seconds. If you empty the
drawer with the machine off, you will not be able to dispense coffee the next
time you switch the machine on.
Please follow these simple instructions to correctly use the “Aqua prima” filter:
1. Keep the “Aqua prima” filter cool and away from sunlight; the room temperature should be between +5°C and +40°C;
2. Do not use the filter in temperatures over 60°C.
3. If the coffee machine is not used for 3 days, we recommend washing the
“Aqua prima” filter;
4 If the coffee machine is not used for more than 20 days, it is advisable to
replace the filter.
5. To store an already opened filter, seal it in a nylon bag and keep in the fridge;
do not store it in the freezer to avoid damaging the filter properties.
6. Before using the filter, leave it to soak in the water tank for 30 minutes.
7. Once it is taken out of its pack, do not keep the filter in the open air.
8. The filter must be replaced 90 days after opening the packing or after treating
60 litres of drinking water.
DREGDRAWER FULL
BREWUNIT MISSING
Fit the brew unit properly in place.
DREGDRAWER MISSING
Fit the drip tray and dregs drawer properly in place.
CLOSE DOOR
Close the front door.
Load the circuit (Starting up).
VENTILATE
BREWUNIT BLOCKED
Contact an authorised service centre.
GRINDER BLOCKED
PROBLEMS - CAUSES - REMEDIES
CAUSES
REMEDIES
The machine does not The machine is not Move the main switch to ON.
turn on.
connected to the power
Check the plug and the
supply.
connection.
PROBLEMS
CAUSES
Coffee flows out in Excessively fine grind
slow trickle or not
at all.
REMEDIES
Adjust to a coarser grind (turn
the knob clockwise).
ENGLISH
PROBLEMS
The coffee is not hot The cups are cold.
Warm up the cups.
enough.
A low temperature has Set the machine on a higher
been set.
temperature.
Only
water
is No preground coffee has Dispense
again
after
dispensed when you been introduced.
introducing preground coffee.
select
“preground
coffee”.
No hot water or steam The tube
is dispensed.
clogged.
nozzle
is Clean the nozzle opening
with a needle.
During this operation, the knob must
be closed and the machine
must be off.
The machine takes a Excessive
long time to warm up. built up.
scale
has Descale the machine.
The brew unit cannot The unit has stopped in Close the door and switch on
be removed.
the wrong position.
the machine; the brew unit
will move back into position.
41
and SBS control turned to Turn the SBS control toward
the left.
the right.
Download PDF

advertising