Color LaserJet 2500L

HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronic Accessories
Cable (Interface)
C2950A
IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) 2.0m (6.6ft) long
5063-1256
New Part for C2950A
C2951A
IEEE-1284 Bi-Tronics parallel cable - DB-25 (M) connector (type A) to 36 pin Centronics (M) connector (type B) 3.0m (9.8ft) long
C6518A
Universal serial bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long
de
Interface (Product)
Ethernet 10Base-T (RJ-45) EIO network internal print server PC board
J3111A
Ethernet 10Base-T/10Base2 and LocalTalk (RJ-45, BNC, LocalTalk) EIO network PCA
J4135A
JetDirect connectivity card - Has one USB port, one serial (DB9) port and one LocalTalk port - Plugs in the EIO slot
on selected DesignJet and LaserJet printers
J4167A
JetDirect 610N token ring LAN interface board - DB-9 and RJ-45 connectors
J6057A
JetDirect 615N internal print server (10Base-T and 100Base-TX) LAN interface board - Plugs into peripheral EIO
slot - Has a RJ-45 connector - Comes with software on CD-ROM and manual
J6057AR
JetDirect 615N internal print server (10Base-T and 100Base-TX) LAN interface board - Plugs into peripheral EIO
slot - Has a RJ-45 connector - Comes with software on CD-ROM and manual
J6058A
JetDirect 680N internal wireless IEEE-802.11b (Wi-Fi) print server - Plugs into peripheral EIO slot
ct
ro
n
ic
J3110A
Memory (Product)
32MB, 100-pin SDRAM DIMM memory module
C7846A
64MB SDRAM - 100MHz synchronous DRAM - DIMM package
Q1887AX
New Part for C7846A
C9121A
128MB, 100MHz synchronous SDRAM DIMM memory module
El
e
C7845A
Electronics/Power Cords
Cable
C9706-60104
Flat flexible cable - Connects between the DC controller board and the formatter board
15
RG5-6971-000CN
Cable assembly (two 3-pin connectors and a spad lug) - Power cable for the fusing assembly - Connects from the
fusing assembly connector to the chassis ground and the low voltage power supply board
16
RG5-6974-000CN
Cable assembly - Connects the toner cartridge E-label reader assembly on the carousel to the DC controller board
17
RG5-7106-000CN
Cable assembly (two 2-pin connectors) - Connects from the low voltage power supply board to the formatter board
18
RG5-7107-000CN
Cable assembly (8-pin, red wire) - (J402 to J134) Connects the low voltage power supply board to the DC controller
board
19
RG5-7108-000CN
Cable assembly (8-pin, Purple wire) - (J403 to J133) Connects the low voltage power supply board to the DC
controller board
20
RG5-7109-000CN
Cable assembly (two 7-pin connectors) - Connects the DC controller board to the fusing assembly connector
21
RG5-7114-000CN
Cable assembly (two connectors) with shield - Connects between the toner cartridge drive motor and the DC
controller board
22
RG5-7115-000CN
Cable assembly (two connectors) - Connects between the roller engaging sensor (PS714) and the DC controller
board
23
RG5-7117-000CN
Cable assembly (two connectors) - Connects the engaging sensor (PS 712) on the toner cartridge carousel to the
DC controller board
w
w
w
M
K-
14
24
RG5-7122-000CN
Cable assembly - 'Y' type cable (three connectors) - The 14-pin connector splits into an 8-pin connector and a 6-pin
connector - Connects between the DC controller board and the optional paper tray connector
25
RG5-7123-000CN
Grounding cable assembly - Connects between the optional tray connector housing and the metal right side frame
assembly
26
RG5-7126-000CN
Cable assembly (two connectors) - Connects the Sub-high voltage board to the high voltage board
27
RG5-7128-000CN
Cable assembly (four connectors) - Connects between the DC controller board and the leading edge paper sensor
for the fusing assembly (PS720) and the waste toner sensor board
28
RG5-7129-000CN
Cable assembly (two connectors and two spade lugs) - Connects the toner cartridge contacts on the left carousel
side plate to the high voltage power supply
29
RG5-7130-000CN
High voltage cable assembly - Connects between the high voltage board spring contacts and the cables to the toner
cartridge carousel left plate assembly
30
RG5-7144-000CN
Upper cable assembly (with seven connectors) - Interconnects various upper level components to the DC controller
board
© 2004 Hewlett-Packard
1
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronics/Power Cords
Cable
31
RG5-7145-000CN
Front cable assembly (six connectors) - Interconnects various components on the front frame assembly and right
side to the DC controller board
32
RG5-7146-000CN
High voltage cable assembly (four connectors) - Connects between the high voltage power supply board and the DC
controller board
33
RH2-5524-000CN
Flat flexible cable (FFC) - Connects between the laser/scanner assembly and the DC controller board
Clutch
RH7-5366-000CN
Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft - (CL1) Engages
the registration roller assembly, and (CL2) Engages the roller within the imaging drum/transfer assembly from the
main gear train
de
34
Connector
RH2-5519-000CN
Connector assembly - For optional paper tray - Mounts to the bottom right side of the middle frame assembly
36
RH2-5520-000CN
Connector for the fusing assembly (F) - 7 small contol pins plus 3 separated high current pins - Mounts in the
connector housing mounted on the bottom pan of the printer
ic
35
Cover
RB3-0120-000CN
Solenoid cover (Steel) - Cover for the multi-purpose tray pickup roller solenoid (SL92)
ct
ro
n
37
Drive Assembly
38
RG5-6911-000CN
Rotary drive assembly - Includes the carousel rotating motor (DCM703), toner cartridge drive motor (PM705),
developing rotary stopper solenoid (SL93), bracket, and gears - Mounts on the right top rear of the print engine
Fan
39
RH7-1537-000CN
Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA) - (FM712)
Mounts in the airflow guide/fan bracket assembly on the left side of the printer
Ground Plane
RB2-9942-000CN
Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards Mounts on the top left of the front frame assembly
41
RB3-0119-000CN
Grounding plate - Grounds the paper pick-up solenoid cover to the right side metal chassis
El
e
40
Insulator
42
RB3-0056-000CN
Insulating sheet (Transparent plastic) - Mounts to the underside of the middle frame assembly
RG5-6880-000CN
K-
Laser/Scanner
43
Laser/scanner assembly - Mounts in the center of the scanner support assembly
Lever
RB3-0179-000CN
Motor
45
Left side lock release lever - Part of locking system used to secure the fusing assembly in the printer
M
44
RF5-4010-000CN
Main motor assembly - Large motor mounted on a controller PC board - Mounts on the inside of the metal right side
frame assembly
New Part for RF5-4010-000CN
RG5-6958-000CN
Rotary motor assembly - (DCM703) Rotates the four color toner cartridges in the carousel to position one of them for
printing
47
RH7-1533-000CN
Stepping motor - 24V DC - (PM704) Swings (or engages) the toner cartridge carousel in place to transfer toner Mounts in the recess on the left side of the rear frame assembly
48
RH7-1535-000CN
Stepping motor (24V) - (PM705) Used to drive the internal rollers and mechanisms in the toner cartridge when it
has been rotated in the printing position on the carousel
w
w
w
RF5-4010-020CN
46
PC Board
49
C9145-69001
Formatter board assembly - Includes the formatter board and all the metal cage covers - Mounts towards the rear on
the metal right frame assembly
REQUIRES RETURN OF DEFECTIVE PART
C9145-67901
New Part for C9145-69001
C9705-69003
DC controller board - Mounts on the left side of the printer (Behind the formatter board assembly)
REQUIRES RETURN OF DEFECTIVE PART
RG5-6959-060CN
New Part for C9705-69003
51
RG5-6964-000CN
Carousel position and toner level photoelectric sensor PC board - 'L' Shaped PC board with the two sensors (PS51) Mounts on the left plate in the toner cartridge carousel
52
WG8-5382-000CN
Sensor PC board - Small board with flag activated photosensor - (PS718) Paper sensor for the multi-purpose tray Mounts in lower right of the front frame and (PS720) fusing assembly front of page sensor - Mounts on bottom of the
middle frame (two used)
50
© 2004 Hewlett-Packard
2
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronics/Power Cords
PC Board
RG5-6965-000CN
Waste toner sensor PC board - Small board with an LED and photoelectric sensor - Monitors the level of the excess
toner deposited in the imaging drum/transfer assembly - Mounts on the right side wall of the front frame assembly
54
RG5-6966-000CN
Top of page photoelectric sensor PC board - Includes the photoelectric top of page sensor and the print engine test
switch - (PS71 and SW71) Mounts in the upper left corner of the front frame assembly
55
RG5-6967-000CN
Registration sensor PC Board - Small board with flag activated photosensor - (PS711) Mounts in the registration
assembly on the underside of the middle frame
56
RH7-7146-000CN
Density photoelectric sensor PC board - (PS81) Mounts under the light blocking pad on the top of the front frame
assembly
de
53
Plate
RB3-0057-000CN
Transfer slide plate - Small 'U' shaped metal insert plates - Mount in the bushing wells for the transfer roller on the
middle frame assembly (two used)
58
RB3-0065-000CN
Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor - Mounts on the left
side of the middle frame below the entrance guide assembly
RB3-0066-000CN
Contact plate - copper clad metal spring - Holds the right end of the small 500 Meg-ohm resistor - Mounts on the left
side of the middle frame below the entrance guide assembly
RB3-0286-000CN
Contact plate - Runs between the shaft on the registration roller and the metal entrance guide assembly
ct
ro
n
60
ic
57
Power Cord
Power cord (Flint Gray) - 16 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V in Israel)
8120-6809
Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the United Kingdom,
Hong Kong, Singapore, Malaysia)
8120-6810
Power cord (Flint Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in Australia, New
Zealand)
8120-6811
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 220V in Europe, Saudi Arabia,
South Africa, India, and Korea)
8120-6812
Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 120V in the USA, Canada,
Mexico, Philippines, and Taiwan)
8120-6813
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 220V in South Africa, Saudi
Arabia, and India)
8120-6814
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 220V in Denmark)
8120-6815
Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (For 220V in Switzerland)
K-
El
e
8120-6800
Power Supply
RG5-6960-000CN
High voltage power supply board (HVT) assembly - Has contacts for the eight high voltage springs in the printer Mounts in the bottom pan (Towards the front of the printer)
70
RG5-7124-000CN
Sub-high voltage board - Small auxillary PC board - Mounts in a holder just above the high voltage board
71
RH3-2241-000CN
Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power
switch - Mounts in the bottom pan towards the rear of the printer
72
RH3-2243-000CN
Low voltage power supply - For 220V to 240V AC operation - Includes the AC power input connector and power
switch - Mounts in the bottom pan towards the rear of the printer
w
w
Reader
M
69
RG5-6956-000CN
E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board Mounts in the E-label reader assembly
74
RG5-6957-000CN
E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board - One for the imaging
drum/tranfer assembly, the other for toner cartridges - One mounts to the the front frame assembly, the other to the
toner cartrige carousel assembly
w
73
Sideplate
75
RG5-6942-000CN
Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high
voltage contacts for the toner cartridges - Mounts on the metal carousel support frame
Solenoid
76
RH7-5337-000CN
Solenoid assembly - (SL92) Lever on the solenoid disengages the stop on the drive gear on the paper pick-up roller
for the multi-purpose input tray (tray 1)
77
RH7-5340-000CN
Solenoid assembly - (SL93) Engages to stop rotation when the proper toner cartridge on the carousel is in place for
printing
© 2004 Hewlett-Packard
3
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Electronics/Power Cords
Spring
RB3-0016-000CN
Electrical contact spring - Spring steel wire with compression springs formed on both ends - One end provides
upward pressure on the right bushing for the transfer roller - Connects to high voltage board
79
RB3-0042-000CN
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar
springs, this one is next to the one on the far left - Connects to high voltage board
80
RB3-0043-000CN
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar
springs, this one is on the far right - Connects to high voltage board
81
RB3-0044-000CN
Electrical contact spring - (Front) Provides high voltage to the toner cartridge via a cable assembly and connection
through the carousel plate assembly - Connects to the high voltage board
82
RB3-0045-000CN
Electrical contact spring - (Rear) Provides high voltage to the toner cartridge via a cable assembly and connection
through the carousel plate assembly - Connects to the high voltage board
83
RB3-0046-000CN
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar
springs, this one is just to the left of the one on the far right - Connects to high voltage board
84
RB3-0047-000CN
Electrical contact spring - Mounts on the underside of the middle frame assembly - Connects to high voltage board
85
RB3-0048-000CN
Electrical contact spring - Mounts on the middle frame assembly behind the transfer roller - Of the four similar
springs, this one is on the far left - Connects to the high voltage board
ic
de
78
86
RH7-6051-000CN
ct
ro
n
Switch
Microswitch with lever activator - (SW2) Senses when the top cover is open - Mounts in a holder on the scanner
support assembly
Thermistor
87
RH7-7149-000CN
Thermistor - (TH3) For detecting internal temperature - Mounts to the right side frame assembly just above the DC
controller board
External Case Parts
RB3-0089-000CN
El
e
Arm
88
Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer
assembly drive cams when the top door is open - Mounts on the right side of the top cover door
Bezel
89
RB3-0035-000CN
Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors - Mounts on the right
rear of the printer
Cover
Control panel assembly (mechanical only) - Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons, plus
the various indicator light pipes - All switches and LED's are on the formatter PC board - Mounts to the top of the
right cover assembly
M
RG5-6927-000CN
K-
Control Panel
90
RB3-0030-000CN
Upper rear cover (Quartz Gray plastic) - Mounts on the upper rear of the printer above the face-up output tray door
92
RB3-0032-000CN
Face-down paper output cover (L-Shaped blue plastic) - Serves as the rear of the tray for the face-down output tray
on top of the printer - Mounts in the upper rear of the printer mechanism
93
RB3-0102-000CN
Front inner cover (blue plastic) - Mounts on the front frame above the multi-purpose input tray
94
RB3-0103-000CN
Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the
printer logo
95
RG5-6900-000CN
Top cover assembly (blue plastic) - Includes the molded-in face-down output tray and the lift-up top cover door
assembly
96
RG5-6953-000CN
Right side cover assembly (Quartz Gray plastic) - Includes the DIMM memory door - Mounts on the right side of the
printer
97
RG5-6902-000CN
Left side cover assembly (Quartz Gray plastic) - Includes the power switch button, rod and spring (The power switch
is located on the low voltage power supply board) - Mounts on the left side of the printer
98
RB3-0028-000CN
Left side cover ONLY (Quartz Gray plastic) - Does not include any attaching parts - Mounts on left side of printer
w
w
w
91
Door
99
RB3-0033-000CN
DIMM memory door (Quartz Gray perforated plastic) - Access door for adding or removing printer memory - Mounts
on the right side cover
100
RF5-4007-000CN
Top cover door (blue plastic) - For accessing the toner cartridges and the imaging drum/transfer assembly - Mounts
to the top cover frame
© 2004 Hewlett-Packard
4
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
External Case Parts
Foot
101
RB2-6297-000CN
Rubber foot - Square self-adhesive rubber foot - Mounts on the rear of the middle frame assembly - Printer foot (two
used)
Holder
102
RB3-0006-000CN
Holder - Housing for the fusing connector assembly - Mounts on the bottom pan of the printer
Label
RS6-8662-000CN
Image cartridge label - Shows the imaging drum/transfer assembly removal steps - Mounts on the right side of the
front inner cover (Visible when the top cover is lifted)
de
103
Lever
104
RB3-0178-000CN
Right side lock release lever - Part of locking system used to secure the fusing assembly in the printer
Rod
RB3-0037-000CN
Power switch rod - Goes between the power button and the power switch on the low voltage power supply board Mounts on the left side cover
ic
105
Shaft
RB2-4933-000CN
Lock release shaft (Small shaft with locking tab) - Does NOT include the lock release lever - Used to secure the
fusing assembly in the printer (2 used)
ct
ro
n
106
Spring
107
RS6-2759-000CN
Power switch spring - Provides tension for power switch button - Mounts on the left side cover
Tray
108
RB3-0176-000CN
Face-Up output tray door (ONLY) - Pull-down tray door for face-up output - Mounts to the top of the locking bracket
on the fusing assembly
109
RG5-6931-000CN
Face-up output tray assembly - Includes the pull-down door and fusing assembly locking bracket (Does NOT include
the lock releases) - Pull-down tray door for face-up output - Mounts to the rear of the fusing assembly
El
e
Fusing Assembly Parts
Bushing
110
RB2-2973-000CN
Support bushing - Mounts on each end of the pressure roller in the fusing assembly
Fusing Assembly
RG5-6903-000CN
Fusing assembly - For 110V to 127V AC operation - Bonds the toner to the paper with heat - Slides in and locks in
lower rear of printer
112
RG5-6913-000CN
Fusing assembly - For 220V to 240V AC operation - Bonds the toner to the paper with heat - Slides in and locks in
lower rear of printer
M
Guide
K-
111
RG5-6929-000CN
Separation guide assembly - Includes the plastic guide, label, and the two small spring loaded rollers - Upper case
and paper guide for the fusing assembly
114
RG5-6930-000CN
Lower separation guide assembly - Includes the guide bracket, paper output sensor (PS1) and flag, exit drive shaft
with two rubber rollers, shaft gear, and idler gear - Mounts in the lower rear on the fusing assembly
Shaft
RB2-4933-000CN
Lock release shaft (Small shaft with locking tab) - Does NOT include the lock release lever - Used to secure the
fusing assembly in the printer (2 used)
w
115
w
113
Other Accessories
w
Cartridge
116
C9700A
HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage
117
C9701A
HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage
118
C9702A
HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage
119
C9703A
HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage
120
C9700-67901
HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage - For CREW
fulfillment
121
C9701-67901
HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage - For CREW
fulfillment
122
C9702-67901
HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage - For CREW
fulfillment
123
C9703-67901
HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage - For CREW
fulfillment
© 2004 Hewlett-Packard
5
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Other Accessories
Cleaning Supplies
5090-3379
Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for clening up toner spills
Drum
125
C9704A
Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000
pages for black print only, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages)
126
C9704-67901
Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000
pages for black print ONLY, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) For CREW fulfillment
5851-1468
LaserJet printer family paper specification guide
C9706-90926
HP Color LaserJet 2500 series service manual
de
Manual
Paper
LaserJet Satin finish tough paper - A size (8.5 x 11-inches) - Will not tear and will withstand outdoor weather
conditions - Can print on both sides
Q1298B
LaserJet Satin finish tough paper - A4 size (21.0cm x 29.7cm) - Will not tear and will withstand outdoor weather
conditions - Can print on both sides - 50 sheets per box
ct
ro
n
ic
Q1298A
Tray Assembly
C9698A
Optional 250 sheet paper input tray - Includes tray base which attaches to printer, and the slide out paper tray Accommodates 148mm x 210mm (5.8 x 8.3 inches) to 216mm x 356mm (8.5 x 14 inches) media - Only one 250
sheet tray supported per printer
C9699A
Optional 500 sheet paper input tray - Includes tray base which attaches to tray 2, and the slide out paper tray Accommodates 216mm x 279mm (8.5 x 11 inches) or 210mm x 279mm (8.3 x 11.7 inches) media - Optional 250
sheet tray must be installed first
El
e
Other Internal Parts
Airflow Guide
RB2-9904-000CN
Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right
side - Directs air flow from the fan on the left side of the printer to the fusing assembly - Snap locks in center rear of
printer
134
RB3-0025-000CN
Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic) - Mounts on the left metal side frame
assembly
K-
133
Bushing
RB2-9808-000CN
Bushing/shaft retainer assembly (Black plastic) - Holds the rotation drive shaft in the right side plate of the toner
cartridge carousel (rotary) assembly
136
RB2-9809-000CN
Bushing/shaft retainer assembly (White plastic) - Holds the rotation drive shaft in the left side plate of the toner
cartridge carousel (rotary) assembly
137
RS5-1635-000CN
Shaft bushing - Mounts on the plate of the multi-purpose paper pick-up gear assembly
138
RS5-1637-000CN
Bushing (black plastic) - mounts on the left end of the registration roller assembly
139
RS5-1638-000CN
w
Carousel
RG5-6910-080CN
w
Clip
Bushing - For the registration roller gear drive shaft - Mounts on the right side of the front frame assembly
Carousel (Rotary) assembly - Includes the carousel assembly, the support assembly, end plates, drive gears and
shaft, sensors, and cables - Mounts towards the rear of the printer in front of the rear frame assembly
w
140
M
135
141
WT2-5056-000CN
Cable clip - Mounts in the opening on the cover for the paper pick-up solenoid
142
WT2-5737-000CN
Cable clip - Mounts on the base assembly pan (two used)
143
XD2-1100-502CN
E-ring clip - Secures the dual gear to the drive shaft which drives the registration roller - Located on the inside of the
front frame assembly
Cover
144
RB3-0052-000CN
Gear Cover (Small Black plastic cover) - Protects the idler gear for the transfer roller - Mounts toward the left side of
the middle frame assembly
145
RB3-0104-000CN
Roller cover - Covers the multi-purpose paper pick-up roller assembly - Mounts in the lower portion of the front
frame assembly
146
RB3-0120-000CN
Solenoid cover (Steel) - Cover for the multi-purpose tray pickup roller solenoid (SL92)
© 2004 Hewlett-Packard
6
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Other Internal Parts
Damper
147
RB2-6248-000CN
Damper assembly (Gray plastic piece with small 13 tooth gear on it) - Helps to reduce clunking when the paper pickup roller is engaged - engages the paper pick-up roller
Flag
148
RB2-9925-000CN
Sensor arm and flag - Activates the photosensor (Does NOT include the roller) - For the Leading edge paper sensor
for the fusing assembly (PS720) - Protrudes up through the feed plate on the middle frame assembly
149
RB3-0135-000CN
Test print flag (Black lever) - Used to activate the print engine test switch - Mounts in a metal holder in the upper left
of the front frame assembly
de
Gear
RB3-0022-000CN
22 tooth gear (Black plastic) - Small gear with diagonally cut teeth - Idler gear between the transfer roller assembly
and the feed drive shaft - Mounts on the left side of the middle frame assembly
151
RB3-0091-000CN
16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab - Used as part of the mechanism to
disengage the drive cams for the imaging drum/transfer assembly - Mounts on the inside of the right side metal
chassis assembly
152
RB3-0092-000CN
15 tooth gear with drive shaft (Black plastic) - Used as part of the mechanism to disengage the drive cams for the
imaging drum/transfer assembly - Mounts on the right side metal chassis frame
153
RS7-0418-000CN
26 tooth gear (Black plastic) - Has 1/8th portion of gear cut away - Mounts on the end of the paper pick-up roller for
the multi-purpose input tray (tray 1)
154
RS7-0424-000CN
Dual gear - 20 tooth / 40 tooth - Mounts on the right side of the front frame assembly
155
RS7-0425-000CN
30 tooth gear (White plastic) - Part of the drive gears for the registration roller - Mounts on inside of the front frame
assembly on the right side
156
RS7-0426-000CN
Dual gear - 26 tooth / 50 tooth (White plastic) - Part of the drive gears for the registration roller - Mounts on inside of
the front frame assembly on the right side
157
RS7-0428-000CN
30 tooth gear (White plastic) - Mounts on the end of the registration roller drive shaft
158
RS7-0429-000CN
26 tooth gear (White plastic) - Has recess for shaft drive pin - Mounts on the right side of the front fame assembly
159
RS7-0435-000CN
Dual gear - 32 tooth / 37 tooth (White plastic) - Drives the upper top bin output roller - Mounts on the right side of the
rear frame assembly
160
RS7-0436-000CN
Dual gear - 37 tooth / 43 tooth (White plastic) - Part of the gear train for driving the upper top bin output roller Mounts on the right side of the rear frame assembly
161
RS7-0437-000CN
51 tooth gear (White plastic) - Main drive gear for both the upper and lower top bin output rollers
K-
El
e
ct
ro
n
ic
150
Gear Assembly
RG5-6938-000CN
Ground Plane
Gear assembly - Metal plate with two White plastic gears attached - Part of the drive gears for the paper pick-up
roller for the multi-purpose input tray (tray 1) - Mounts on the right side of the front frame assembly
M
162
RB2-9942-000CN
Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards Mounts on the top left of the front frame assembly
164
RB3-0119-000CN
Grounding plate - Grounds the paper pick-up solenoid cover to the right side metal chassis
165
RB2-9903-000CN
166
RB2-9912-000CN
Top output bin guide - Small curvered ribbed black plastic piece - Snaps on the rear of the printer just below the
upper top bin output roller (two used)
w
Guide
w
163
167
RB2-9954-000CN
Left paper feed guide (small Black plastic arm) - Mounts to the left of the separation pad assembly on the lower front
frame assembly
168
RB2-9955-000CN
Right paper feed guide (small Black plastic arm) - Mounts to the right of the separation pad assembly on the lower
front frame assembly
169
RG5-6935-000CN
Left cartridge guide assembly - For the imaging drum/transfer assembly - Mounts on the left metal side frame
w
Cable guide (Quartz Gray plastic) - Protects and supports the upper cable assembly - Mounts to the right rear on the
laser/scanner support assembly
Holder
170
RB2-9924-000CN
Sensor assembly mounting holder - For mounting the leading edge paper sensor for the fusing assembly (PS720) Mounts to the underside of the middle frame assembly
171
RB3-0023-000CN
Interlock switch holder (Quartz Gray plastic) - Mounts to the laser/scanner support assembly - Towards the left rear
of the printer
© 2004 Hewlett-Packard
7
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Other Internal Parts
Insulator
172
RB3-0007-000CN
Insulating sheet (Transparent plastic) - Mounts between the bottom pan and the high and low voltage power supply
boards
173
RB3-0056-000CN
Insulating sheet (Transparent plastic) - Mounts to the underside of the middle frame assembly
Pad
174
RF5-4047-000CN
Light blocking pad assembly - Black plastic frame with soft rubber gasket and stiff conductive Mylar piece
(grounded) - Mounts to the top center of the front frame assembly
RB2-9916-000CN
de
Plate
175
Mounting/grounding plate - For the engaging motor (PM704) - Mounts in the recess on the upper left side of the rear
frame assembly
Pressure Assembly
176
RG5-6943-000CN
Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor,
and the engaging rod shaft - Primary support structure for the toner cartridge carousel
Rack slide - White plastic piece with gear teeth layed out in rack form on both sides - Part of the mechanism that
disengages the imaging drum/transfer assembly cams when the top cover is opened - Mounts vertically on the metal
right side frame
ct
ro
n
RB3-0090-000CN
ic
Rack Slide
177
Shaft
178
RB3-0060-000CN
Idler gear shaft - Short metal rod - Shaft for the transfer and feed drive idler roller - Mounts on the left side of the
middle frame assembly
Shield
179
RB2-9932-000CN
RFI shield - Parallel wire form mounted over the fan - Mounts on the fan air duct assembly on the left side of the
printer
RG5-6932-060CN
Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer
assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) Mounts on the right side
RG5-6932-070CN
New Part for RG5-6932-060CN
RG5-6934-000CN
Right rear side plate assembly - Includes the rear half of the metal right side plate, the fusing assembly drive motor
and the three associated gears - Mounts on rear half of right side of printer
K-
181
El
e
Sideplate
180
Spring
RB3-0121-000CN
Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer - Mounts on
the upper right side of the front frame assembly
183
RB3-0122-000CN
Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer - Mounts on the upper left
side of the front frame assembly
184
RS6-2766-000CN
Tension spring - Provides a small amount of return tension for the sensor flag arm on the leading edge sensor for
the fusing assembly (PS720)
w
Support
PC board support (Black plastic holder) - For mounting the small sub-high voltage board above the high voltage
board
w
RB3-0062-000CN
186
M
182
RG5-6907-000CN
Laser/scanner support assembly (sheet metal plate) - Crossmember between the two side frames - Support for the
laser/scanner assembly, the toner cartridge carousel drive motor, and the cover interlock switch assembly
w
Tray
187
RB3-0019-000CN
Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum - Mounts just below
the toner cartridge carousel on the bottom frame assembly
Paper Input Tray Parts
Guide
188
RG5-6951-000CN
Paper guide assembly - Paper width adjustable guide assembly for the multi-purpose front input tray (tray 1) Mounts with the two hinges on the lower portion of the front frame assembly
Hinge
189
RB2-3041-000CN
Tray hinge - For the left side of the multi-purpose front input tray (tray 1) - Mounts in the lower portion of the front
frame assembly
190
RB2-3042-000CN
Tray hinge - For the right side of the multi-purpose front input tray (tray 1) - Mounts in the lower portion of the front
frame assembly
© 2004 Hewlett-Packard
8
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Paper Input Tray Parts
Spring
191
RS6-2030-000CN
Tension spring - Provides support tension for the multi-purpose front input tray guide assembly (two used)
Tray Assembly
192
RG5-6937-000CN
Multi-purpose front input tray assembly (tray 1) - Includes the front cover piece, pull-out paper support, and the flipout extender - Mounts on front of printer (on the front frame assembly)
Paper Path Parts
Belt
RB1-8668-030CN
Feed guide drive belt - Small belt approximately 5/16 inch wide with 'A' shaped ribs on it - Between the feed drive
roller and the small center roller - Driven via the transfer roller gear train
194
RB3-0063-000CN
Feed belt - Small black rubber belt approximately 1/8 inch wide with little 'A' shaped ribs on it - Goes between the
feed drive roller and the pulley rollers (eight used)
de
193
Bushing
RB2-3043-000CN
Left roller bushing - Acts as the bearing and retainer for the left end of the paper pick-up roller assembly (tray 1) Mounts on the left side of the front frame assembly
196
RB2-3044-000CN
Right roller bushing - Acts as the bearing and retainer for the right end of the paper pick-up roller assembly (tray 1) Mounts on the right side of the front frame assembly
197
RB3-0014-000CN
Bushing assembly (black plastic bushing with small guide roller on top) - Holds the right end of the transfer roller
assembly in the middle frame assmebly
ct
ro
n
ic
195
Drum
C9704A
Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000
pages for black print only, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages)
199
C9704-67901
Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000
pages for black print ONLY, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages) For CREW fulfillment
El
e
198
Flag
200
RB2-9925-000CN
Sensor arm and flag - Activates the photosensor (Does NOT include the roller) - For the Leading edge paper sensor
for the fusing assembly (PS720) - Protrudes up through the feed plate on the middle frame assembly
201
RB3-0111-000CN
Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other - Senses paper
coming from the multi-purpose front input tray (tray 1)
RF5-4049-000CN
K-
Guide
202
Entrance guide assembly - Angled metal guide between the registration roller and the transfer roller - Mounts to the
middle frame assembly
RF5-4012-000CN
Plate
RB3-0010-000CN
Pulley
Separation pad assembly - Includes the separation pad, holder and spring - Mounts below the multi-purpose front
input (tray 1) pick-up roller assembly
Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through - Mounts behind the
transfer roller on the middle frame assembly
w
204
M
Pad
203
RB3-0061-000CN
Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1.75-inches) long with
three ball type pulleys - Mounts just behind the tranfer roller in the middle frame assembly (two used)
206
RB3-0067-000CN
Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (0.625-inch) long with one ball
type pulley - Mounts just behind the tranfer roller in the middle frame assembly (two used)
w
w
205
Roller
207
RB2-7195-000CN
Sensor flag roller (small White plastic roller) - Mounts in the sensor arm flag for the leading edge paper sensor for
the fusing assembly (PS720)
208
RB2-9908-000CN
Pressure roller (small black hard plastic 'disked' roller) - Rides up against the upper top bin output roller on the top
rear of the printer (two used)
209
RB2-9909-000CN
Pressure roller (small Black hard plastic 'solid' roller) - Rides up against the lower top bin output roller on the middle
rear of the printer (two used)
210
RB3-0012-000CN
Belt roller - Small oval shaped roller approximately 1-3/4 inches long - Mounts toward the center of the metal feed
plate on the middle frame assembly
211
RB3-0160-000CN
Paper pick up roller (D-shaped) - Mounts on the paper pick up roller assembly for the multi-purpose front input tray
(tray 1)
© 2004 Hewlett-Packard
9
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Paper Path Parts
Roller Assembly
RF5-4040-020CN
Transfer roller assembly - Long black foam type roller - Transfers static charge to paper - Mounts towards the front
and on top of the middle frame assembly
213
RG5-6897-000CN
Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two
anti-reversing flaps, and the drive gear - Mounts on the top rear of the printer
214
RG5-6936-000CN
Lower top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, and the
drive gear - Mounts in the center on the rear frame assembly (above the fusing assembly)
215
RG5-6939-000CN
Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag Mounts from the bottom toward the front center of the middle frame assembly
216
RG5-6952-000CN
Paper pick-up roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers Picks paper from the multi-purpose front input tray (tray 1) - Mounts in the lower portion of the front frame assembly
de
212
Shaft
RB3-0011-000CN
Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley Mounts behind the transfer roller on the middle frame assembly
ic
217
Shutter
RG5-6940-000CN
Registration shutter assembly - Includes the metal roller, mounting frame, grounding springs, and the dual coupling
gear - Mounts over the registration roller at the front of the middle frame assembly
ct
ro
n
218
Spring
RB2-9905-000CN
Torsion spring - Provides pressure for the upper top bin output pressure rollers (two used)
220
RB2-9906-000CN
Torsion spring - Provides pressure for the lower top bin output pressure rollers (two used)
221
RB2-9952-000CN
Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag - Mounts in the lower portion of the front frame
assembly
222
RB3-0015-000CN
Compression spring - Provides upward pressure for the left bushing on the transfer roller assembly
223
RB3-0016-000CN
Electrical contact spring - Spring steel wire with compression springs formed on both ends - One end provides
upward pressure on the right bushing for the transfer roller - Connects to high voltage board
El
e
219
Static Dissipater
RB3-0009-000CN
Static eliminator ground plate - Right angled metal piece with small teeth on top edge - Mounts from underneath on
the middle frame assembly just behind the pulley rollers
w
w
w
M
K-
224
© 2004 Hewlett-Packard
10
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
ct
ro
n
ic
de
PC Board Assembly Locator
_
56
_
50
_
49
_
53
_
71, 72
_
_
_
55
70
w
w
w
69
_
M
51
K-
El
e
54
_
© 2004 Hewlett-Packard
11
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
External Covers
90
/
91
\
89
\
ct
ro
n
ic
de
99
/
88
/
K-
El
e
\
92
w
w
w
M
98
/
© 2004 Hewlett-Packard
\
105
\
107
|
100
12
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
External Covers (Assemblies)
|
95
w
w
w
M
K-
El
e
ct
ro
n
ic
de
96
|
|
97
© 2004 Hewlett-Packard
13
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Front Frame Assembly
103
\
73, 74
|
93
\
56
\
196
\
/
149
141
/
158
\
ic
182
|
37, 146
\
137
/
ct
ro
n
76
\
de
54
|
174
|
153
\
201
\
221
\
\
147
El
e
\
52
/
183
195
\
\
154
|
162
203
|
\
189
|
156
M
|
139
/
143
\
190
\
168
\
167
\
40, 163
\
145
w
/
155
K-
\
41, 164
w
w
188
|
|
211, 216
/
191
|
192
\
94
/
191
© 2004 Hewlett-Packard
14
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Internal Components (1 of 2)
213
|
30
\
de
202
|
ic
159
\
/
208
/
219
ct
ro
n
152
\
151
\
\
160
\
161
187
/
197
\
El
e
212
|
\
47
\
87
\
39
w
w
134
\
w
M
K-
\
222
/
179
31
/
© 2004 Hewlett-Packard
15
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Internal Components (2 of 2)
33
\
43
\
86
\
de
\
165
ct
ro
n
ic
/
171
El
e
21
/
116, 117, 118, 119,
120, 121, 122, 123
|
K-
|
186
\
14
w
w
w
M
\
50
\
125, 126, 198, 199
|
169
© 2004 Hewlett-Packard
16
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Main Drive Assembly
180
de
_
22
/
ct
ro
n
ic
177
/
34
_
w
w
w
M
K-
El
e
181
|
|
45
© 2004 Hewlett-Packard
17
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Rear Frame Assembly
ct
ro
n
ic
de
214
|
/
166
El
e
/
220
|
175
w
w
w
M
K-
/
209
\
133
© 2004 Hewlett-Packard
18
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Middle Frame Assembly
193
\
210
\
\
194
217
\
\
205
\
\ 194
206
\
206
\
\ 194
\ 194
194
218
|
57
/
78, 223
|
\
205
\
\ 194
\ 194
194
_
/
57
/
144
24
|
ct
ro
n
25
|
ic
58
/
\
\ 178
150
101
de
204
\
\
35
157
\
60
|
_
K-
101
El
e
\
138
148, 200
|
/
84
M
|
82
w
/
207
224
\
52
170
/
w
/
29
\
83
184
/
_
\
80
/
81
w
\
27
/
85
\
42, 173
|
79
© 2004 Hewlett-Packard
|
215
19
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Toner Cartridge Carousel Assembly
_
23
140
_
176
|
135
/
w
w
w
136
\
M
K-
El
e
ct
ro
n
ic
de
16, 74
|
/
28
|
75
© 2004 Hewlett-Packard
20
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
de
Toner Cartridge Carousel Drive Assembly
38
77
/
\
48
w
w
w
M
K-
El
e
46
\
ct
ro
n
ic
_
© 2004 Hewlett-Packard
21
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Power Supply Base Assembly
\
18
de
17
|
\
19
ic
71, 72
\
\
26
69
\
ct
ro
n
36
/
20
|
|
15
El
e
\
32
\
172
\
70
w
w
w
M
K-
102
\
\
178
/
142
© 2004 Hewlett-Packard
22
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
Fusing Assembly
_
108, 109
|
111, 112
113
|
104
|
106, 115
|
El
e
44
|
ct
ro
n
ic
de
106, 115
|
\
110
w
w
M
K-
\
110
w
|
114
© 2004 Hewlett-Packard
23
HP Color LaserJet 2500L printer
HP Parts Reference Guide™
www.hp.com/go/hpparts
HP Parts Reference Guide
http://www.hp.com/go/parts
HP PartSurfer
http://partsurfer.hp.com
de
HP Parts Ordering Information
http://www.hp.com/go/hpparts
HP Parts Questions/Comments
w
w
w
M
K-
El
e
ct
ro
n
ic
http://partsurfer.hp.com/contactus.htm
© 2004 Hewlett-Packard
24
Download PDF