garage door opener programmable lcd wall console

3
Button)/Set
LCD DISPLAY
INSTRUCTION
MANUAL
6
7
ACTION
LCD DISPLAY
11. The LED light will flash 3 times.
12. The LCD display will flash the number “4”.
13. Press the
button again to close the garage door
to its fully closed position. The flashing “4” will
change to solid.
Œ
Learn or Erase Remote Control

Light Bulb is Turned On (Manually)
Ž
Door Open

Door Close

Lock Enabled (Manually or Lock Timer)
warnings
‘
Terminate Lock Timer
’
Clock or Time Setting
“
Safety Beam Sensor Activated
”
Operation Failure
headline
•
Pbars
rogramming Mode
model no. 046-0509-4 | contact us 1-800-689-9928
16. Press
button again to confirm the force at the
desired level.
notes
Program a Wireless Keypad: Within 30 seconds,
activate the keypad by entering: (A) Pin code plus #
[PIN#] for single door operation. (B) Pin code plus [#]
plus [door number] for multiple door operation.
notes
19. The garage door opener will beep if remote is
successfully programmed and the flashing remote
icon will change to solid.
21. If you need to program additional remote, press
warnings
Ç button, then refer to step 18. After you’ve
programmed all remotes, press
button.
LED
2. Press and hold
button for 5 seconds until the
LCD display shows the number “1” and up and down
arrows are flashing.
4. Press the
warnings
White | Black
WARNING:
warnings
•
Wall console must be installed within sight of the garage door, out of reach for
children, at a minimum height of 5’ (1.5 m), and away from all moving parts of
door.
•
Be sure power is not connected before installing the wall button.
•
Wall console should only be activated when door can be seen clearly, is
properly adjusted, and there are no obstructions to door travel.
•
Always keep garage door in sight until completely closed. Never permit anyone
to cross path of closing garage door.
“Wall Console” terminals
on the garage door opener.
warnings
6. Press the È button until the door is in fully closed
position.
warnings
8
9
LCD DISPLAY
25. Press Ç/È button to set the hour and press
confirm.
10
model no. 046-0509-4 | contact us 1-800-689-9928
ACTION
continuation tabs
to
26. Press Ç/È button to set the minutes and press
to confirm.
27. The LCD display will show the end lock time setting.
28. Press Ç/È button to set the hour and press
confirm.
button again to confirm.
headline bars
1. Press and hold
24. The LCD display will show the start lock time setting.
(To skip this setting, press
button twice.
7. Press the
8. The LED light will flash 3 times when the travel limit
settings are completed.
headline bars
ACTION
button to confirm the door position.
5. The LCD display will show the number “2”.
Connect the wires to the

If the LED indicator on the wall console is not glowing steadily after installation,
check for:
button for 5 seconds.
notes
to
29. Press Ç/È button to set the minutes and press
to confirm.
2. Press Ç/È buttons to set
the auto close timer.
3. Selection:
“OFF”
= Disarm
“03”
= 3 mins
“10”
= 10 mins
“30”
= 30 mins
Press
to confirm the setting.
continuation tabs
notes
•
Electric power to the opener.
•
A short in the wires. These can occur at the staples or at the opener
connections.
•
Incorrect wiring between sensor and opener.
•
A broken wire.
•
Check alignment
WARRANTY
4. The wall console will return to standby
mode and display the current time.
This Mastercraft product carries a 1 (one) year LIMITED warranty against defects
in workmanship and materials. This product is not guaranteed against wear or
breakage due to misuse and/or abuse.
30. On-ground programming is completed
warnings
model no. 046-0509-4 | contact us 1-800-689-9928
TROUBLESHOOTING
LCD DISPLAY
23. Press Ç/È buttons to set the clock to the current
time; then, press
to confirm.
20. If you want to erase all the remotes, press and hold
the È button for 5 secs until you see “E.”
15. Press the Ç or È button to set the force 0, 1, 2, or 3
you wish. 0 is the default force level. 3 is maximum
force level.
notes
22. The LCD display will show the time setting.
14. The garage door opener will beep when door is fully
closed and the display will show “F”.
continuation tabs
continuation tabs
3. Press the Ç button until the door is in fully open
position.
LCD DISPLAY
18. Program a Remote: Within 30 seconds, press any
button on the remote that you would like to program
continuation tabs
to the opener.
LCD DISPLAY
1. Connect the opener to an approved power source.
The dot in the LED display stays on.
notes
17. The LCD display will flash the remote icon.
PROGRAMMING
10. Press the
button to open the garage door to its
fully open position. The flashing “3” will change to
solid.
notes
ACTION
9. The LCD display will flash the number “3”.

ACTION
holders.
SET AUTO CLOSE
Before using your wall console, read and understand this owner’s guide.
instruction label next
to the wall console
using staples or tacks.
notes
PROGRAMMING
IMPORTANT:
Œ
continuation tabs

Ž

onto the mounting
bracket until you
hear a click.
model no. 046-0509-4 | contact us 1-800-689-9928
While programming, the Ç and È buttons can be used to move the door as needed.
Route the wire up the wall and across the ceiling to the opener with wire

PROGRAMMING
Light On/Off/Down

Open/Close Door (Push

mounting bracket
continuation tabs with two screws
Slide the wall console
Mount the user safety

Ž
TROUBLESHOOTING
OVERVIEW
Manually Lock/Up
Secure the
Œ
5
model no. 046-0509-4 | contact us 1-800-689-9928
WARRANTY
Programming
Œ
Display

Enable/Disable Lock Timer/
Ž
4
continuation tabs
INSTALLATION
model no. 046-0509-4 | contact us 1-800-689-9928
OVERVIEW
GARAGE DOOR OPENER
PROGRAMMABLE LCD WALL CONSOLE
headline bars
headline bars
INSTALLATION
2
model no. 046-0509-4
PROGRAMMING
s
headline bars
warnings
Made in China
Imported for
Mastercraft Canada Toronto, Canada M4S 2B8