Smeg Retro Küçük Ev Aletleri SJF01 Slow Juicer - Smeg-TR

Contents
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Introduction
User Manual
Intended use
General safety instructions
Manufacturer liability
Identification plate
Disposal
2 Description
2.1 Product description
3 Use
22
22
22
23
25
25
25
26
26
27
3.1 Before first use
3.2 Assembly
3.3 Using the slow juicer
4 Cleaning and maintenance
4.1
4.2
4.3
4.4
4.5
22
EN
1 Instructions
Instructions
Cleaning the surfaces
Cleaning the slow juicer
Removing the seals and rotating brush for cleaning
What to do if...
27
27
29
33
33
33
33
33
35
We advise you to read this manual carefully, it contains all the instructions for maintaining the appliance’s aesthetic
and functional qualities.
For further information on the product: www.smeg.com
The manufacturer reserves the right to make any changes deemed useful for improvement of its products without prior
notice. The illustrations and descriptions contained in this manual are therefore not binding and are merely indicative.
21
Instructions
1 Instructions
1.1 Introduction
Important information for the user:
Instructions
General information on this user
manual, on safety and final
disposal.
Description
Description of the appliance and its
accessories.
Use
Information on the use of the
appliance and its accessories,
advice regarding preparations.
Cleaning and care
Information for correct cleaning and
care of the appliance.
Safety instructions
Information
Advice
22
1.2 User Manual
This user manual is an integral part of the
appliance and must therefore be kept in its
entirety and in an accessible place for the
whole working life of the appliance.
1.3 Intended use
• The appliance is designed exclusively for
home use.
• Do not use the appliance for anything
other than the intended use.
• Use the appliance indoors.
• The appliance can be used to extract fruit
and vegetable juices for various
preparations.
• The appliance is not designed to operate
with external timers or with remotecontrol systems.
• This appliance must not be used by
people (including children) of reduced
physical, sensory or mental capacity, or
lacking in experience in the use of
electrical appliances, unless they are
supervised or instructed by adults who
are responsible for their safety.
Instructions
• Do not plug in or unplug with wet hands.
This may cause electric shock or injury.
• Plug the power cord correctly and push it
tight in a wall socket. This may cause
electric shock or fire.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
or similarly qualified persons in order to
avoid a hazard. If the power cord is
damaged, it may cause electric shock or
fire.
• Never alter the appliance. Also, do not
disassemble or repair by yourself.
Do not insert fingers, foreign substances
or objects such as pins into gaps or holes
in the body. This may cause a fire,
electric shock or failure. For any
technical support, contact the authorised
local Customer Care Centre.
• In case the power cord breaks or is
damaged or the plug-in part becomes
loose, do not operate it. This may cause
electric shock, fire or injury.
• Do not moisten the body or splash water
on the body. Be careful not to let any
liquids or other substances get into the
switch on the appliance. Do not operate
the switch with wet hands. It may cause
electric shock or fire.
• For your safety, have the grounding
connection perfomed. Make sure that
the grounding is not done on gas pipes,
plastic water pipes, telephone wires, etc.
This may cause electric shock, fire,
malfunction or explosion. Be sure to use
the electrical outlet with ground
connection.
• Never disassemble the chamber set
during operation or insert fingers, foreign
objects such as forks, spoons, etc. into
the hopper chute or juice outlet. This may
cause injuries, accidents or failure.
• Do not operate without locking the
hopper properly. It may cause injury or
failure.
• When detecting a gas leak, do not insert
the power cord into its slot. Open the
window immediately to ventilate fully.
This may cause injury or failure.
• Never put fingers, forks or spoons, etc.
into the juice outlet. This may cause injury
or failure.
• If rotation of the auger is stopped in
normal operation, activate the REVERSE
function and hold for 2-3 seconds and
then after the REVERSE function has
stopped completely, press the ON
button again. If the auger keeps stopping
during operation, the parts may get
damaged and performance may be
affected due to the motor overheating. If
the problem persists, stop the appliance
immediately and contact your local
Customer Care Centre.
23
EN
1.4 General safety instructions
Instructions
• During operation, do not try to move the
body, disassemble the chamber set or
parts and try to lock them. This may
cause injuries or failures. Always switch
off the appliance and unplug the power
cord before carrying out any operation.
• When using the appliance, avoid
wearing neckties, long necklaces,
scarves, etc., which could get entangled
into the hopper chute. This may cause
injury, failure or breakage.
• Place the appliance on a flat and stable
surface. This may cause injury or failure.
• Do not operate the appliance for more
than 30 minutes at a time. This may
cause a motor failure due to overheating.
Cool it down sufficiently for about 5
minutes and operate it again.
• When placing ingredients into the
hopper chute, only use the pusher
provided. This may cause injury or
failure.
• Avoid dropping or causing a severe
shock to the appliance. It may cause
electric shock, fire or damage.
• If the appliance gives off an unpleasant
smell or it heats excessively or smokes,
stop using it immediately and contact
your local customer care centre. When
using a new appliance, it gives off a
smell and this disappears naturally over
time.
24
• Always unplug the appliance after use.
Always disconnect the appliance from
the supply if it is left unattended and
before assembling, disassembling or
cleaning. When unplugging the power
cord, make sure to hold the power cord.
Pulling on the wire to unplug may cause
electric shock or fire.
• Do not wash at high temperatures of
80°C or higher. Do not put the
appliance in a dishwasher, a dryer or a
microwave, etc. This may cause a failure
or parts deformation.
• The appliance weighs about 6.2kg.
When moving the appliance, ensure to
move it holding the grips tightly at the
bottom of the body with both hands. If
you try to hold the chamber or the edge
of the body, the base is likely to fall and
cause injury or failure.
• Appliances can be used by persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and if
they understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be performed by
children. This appliance shall not be used
by children. Keep the appliance and its
cord out of reach of children.
1.5 Manufacturer liability
The manufacturer shall not be held
responsible for personal injuries or property
damage caused by:
• Any use of the appliance other than the
one it was designed for.
• Not having read the user manual.
• Tampering with any part of the
appliance.
• The use of non-original spare parts.
• Not following the safety instructions.
1.6 Identification plate
The identification plate bears the technical
data, serial number and brand name of the
appliance. Do not remove the identification
plate for any reason.
1.7 Disposal
This appliance must be disposed of
separately from other waste
(Directive 2012/19/EU). The
appliance does not contain substances in
quantities sufficient to be considered
hazardous to health and the environment, in
accordance with current European
directives.
• Old electrical appliances must not be
disposed of together with domestic
waste! To comply with current legislation,
electrical appliances, on reaching the
end of their useful lives, should be taken
to an appropriate recycling centre for
electrical and electronic waste. In this
way, any valuable material contained in
the old appliances can be recycled,
helping to protect the environment. The
relevant local authorities or their waste
disposal operators can provide further
information.
Our appliances are packed in nonpolluting and recyclable materials.
• Dispose of the packing materials at an
appropriate recycling facility.
Plastic packaging
Danger of suffocation
• Do not leave the packaging or any part
of it unattended.
• Do not let children play with the plastic
bags.
Electrical voltage
Danger of electrocution
• Disconnect the main power supply.
• Unplug the appliance.
25
EN
Instructions
Description
2 Description
2.1 Product description
Slow juicer - model SJF01
1 Hopper
2 Hopper lid
3 Motor body
4 Auger
5 Strainers (fine and coarse)
6 Rotating brush
7 Juice collector bowl
8 Juice outlet
9 Pulp outlet
10 Pusher
26
11 Pulp container
12 Juice jug with lid
13 Lever switch/Reverse function lever
14 Juice density regulation lever
15 Cleaning brushes
16 Seal
The utensils and accessories
intended to come into contact with
food are made of materials that
comply with the provisions of
current legislation.
Use
3 Use
Danger of electrocution
1. Insert the strainer (1) into the slots on the
rotating brush (2) until it locks into
position.
• Plug the appliance into a grounded
three-pin socket.
• Do not remove earth prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions could
result in death, fire, or electrical shock.
3.1 Before first use
1. Remove any protective packaging from
the outside or inside of the appliance,
and its accessories.
2. Remove any labels (apart from the
technical data plate) from the appliance,
its parts and components.
3. Clean the parts and components of the
appliance (see ”4 Cleaning and
maintenance”).
4. Clean the body of the appliance using a
damp cloth.
5. Dry the components thoroughly and
install them.
2. Check that the strainer (1) is correctly
positioned inside the rotating brush (2).
27
EN
3.2 Assembly
Description
3. Position the strainer unit (1) and rotating
brush (2) inside the juice collector
bowl (3) so as to insert the unit into the
slots (4) on the bottom of the bowl.
4. Position the auger (5) by turning it so that
it fits into the slots (6) on the rotating
brush (2).
28
5. Place the hopper (7) onto the bowl,
turning it clockwise until it locks into
position.
Use
CLOSE
position.
3.3 Using the slow juicer
1. Check that the juice density regulation
lever (10) is in the CLOSE
position
before starting the appliance.
2. Place the juice jug (11) and the pulp
container (12) under the relative outlets
(13) and (14).
29
EN
6. Install the assembled unit (8) onto the
motor body (9). Make sure that the juice
density regulation lever (10) is in the
Use
3. Push the lever switch upwards (15) to
start the juicer.
5. Open the juice outlet (18) before the
juice collector bowl becomes full and
move the juice density regulation lever (10)
to the half-open position
before
adding the last ingredients.
4. Introduce the ingredients into the feed
chute of the hopper (16) a little at a time
using the pusher provided (17).
6. When juicing is complete, stop the juicer,
placing the lever switch (15) to the
middle position.
30
How to use the juice density regulation
lever
CLOSE position
Use the lever in the CLOSE position during
the initial phases of fruit or vegetable juice
extraction.
HALF-OPEN position
Use the lever in the HALF-OPEN position
during the last phases of juicing, when the
final ingredients are introduced and when
removing residues.
If semi-hard ingredients are used such as
grapes, pomegranates, blackberries, etc.
move the lever into this position as soon as
the juice starts to exit from the outlet.
OPEN position
Use the lever in the OPEN position when
cleaning the juice collector bowl.
Advice for using the juice density
regulation lever
Ingredients:
Apples, pears, melon, strawberries,
blueberries, plums, peaches, cherries,
pineapple, orange, lemon, grapefruit.
Carrots, ginger, potatoes, beetroot,
broccoli, cauliflowers, cucumbers,
cabbage, savoy cabbages, spinach,
walnuts, almonds.
1. Place the lever in the CLOSE
position before juicing.
2. When juicing is nearly complete, move
the lever to the HALF-OPEN
position.
• Remove the seeds or stones from
fruit such as persimmons,
apricots, lemons, plums,
peaches, etc. before juicing.
• Stalk vegetables with tough
fibres such as celery, fennel,
cardoons, etc. should be cut into
pieces of approximately 3-4 cm.
• Do not introduce sesame seeds,
coffee beans or peppercorns.
• Do not introduce fruit or
vegetables preserved in alcohol,
sugar, honey, etc. They could
damage the appliance or cause
it to malfunction.
• It is best to consume the juice
from leafy green vegetables and
fruit immediately after juicing for
a better absorption of vitamins
and nutrients.
Seed fruit:
Grapes, pomegranates, kiwi fruit,
blackberries.
1. Place the lever in the CLOSE
position before juicing.
2. When the juice starts to come out, move
the lever to the HALF-OPEN
position.
Ingredients to mix with milk:
Bananas, strawberries, blueberries, etc.
1. Move the lever to the CLOSE
position.
31
EN
Use
Use
How to use the REVERSE function
Moving parts
Risk of personal injury or
damage to the appliance
• Do not operate the appliance for more
than 30 minutes at a time. Leave the
appliance to cool down and wait 5
minutes before starting it again.
• Do not insert fingers, forks or spoons into
the juice and pulp outlets. This could
cause personal injury or damage the
appliance.
• Keep hands, hair, clothing, spatulas and
other objects away from the feed chute
of the hopper to avoid personal injury or
damage to the appliance.
• Only use the pusher provided to push the
ingredients into the feed chute of the
hopper.
Advice on which strainer to use
Strainer
Suitable for
Fine
Pure fruit or vegetable
juices.
Coarse
32
Dense juices containing
pieces of pulp,
smoothies, milk shakes or
soups.
The REVERSE function is used when the
auger stops during operation:
• Keep the lever switch pressed
downwards for 3-5 seconds at a time.
Repeat this process 2-3 times.
The REVERSE function pushes the
ingredients upwards, releasing the auger
and allowing the appliance to operate
correctly.
If the auger continues to stop
during operation, unplug the
power cable, remove the juice
collector bowl and clean it.
Cleaning and care
4.1 Instructions
Improper use
Danger of electrocution
• Switch off and unplug the appliance
before cleaning it and its parts.
Improper use
Risk of damage to surfaces
• Do not use steam jets to clean the
appliance.
• Do not use cleaning products containing
chlorine, ammonia or bleach on steel
parts or parts with metallic finishes on the
surface (e.g. anodizing, nickel- or
chromium-plating).
• Do not use abrasive or corrosive
detergents (e.g. powder products, stain
removers and metallic sponges).
• Do not use rough or abrasive materials
or sharp metal scrapers.
4.3 Cleaning the slow juicer
1. Remove the hopper, auger, bowl,
strainer and rotating brush assembly from
the juicer body and disassemble it into its
various parts.
2. Use the cleaning brushes provided to
clean and wash the parts under running
tap water.
3. Clean the body of the juicer using a
damp cloth.
4. Dry parts thoroughly before reinstalling
them.
4.4 Removing the seals and rotating
brush for cleaning
• Juice outlet seal: Open the juice outlet
cap and hold the juice collector bowl
and outlet steady with one hand and
remove the seal with the other.
4.2 Cleaning the surfaces
To keep the surfaces in good condition,
they should be cleaned regularly after use.
Let them cool first.
33
EN
4 Cleaning and maintenance
Cleaning and care
• Juice collector bowl seal: Grasp the
seal on the bottom of the bowl and lift
upwards to remove it.
• Use the cleaning brush provided to
clean the internal and external parts of
the rotating brush unit under running tap
water.
• Rotating brush: Remove the blades as
shown.
Clean and wash the slow juicer
immediately after use. Residues may
dry out and make disassembly and
cleaning difficult, as well as affect
the operation of the appliance.
34
Cleaning and care
Problem
Probable cause
Solution
The plug is not properly inserted
into the power socket.
Insert the plug into the
power socket. Do not use
adaptors or extension
cords.
Check that the main power
switch is turned on.
The appliance does not
work
Make sure that the hopper
The hopper has not been installed is installed properly
properly.
following the assembly
instructions.
Excessive residue
Place the lever into the halfopen position and run the
appliance in order to
remove the residues.
Activate the REVERSE
function for 3-4 seconds at
a time. Repeat 2-3 times.
Presence of hard seeds.
In case of hard seeds,
activate the REVERSE
function in order to push the
ingredients towards the
feed chute of the hopper.
The container is too full.
Use the REVERSE function.
If the problem persists,
contact an authorized
service centre.
It is not possible to detach
the hopper
The auger stops during
operation
Remove some of the
The juice drips onto the
Excessive quantity of ingredients in ingredients and introduce
outside of the juicer body the hopper feed chute.
them gradually.
35
EN
4.5 What to do if...
Cleaning and care
Problem
Probable cause
The juice collector bowl
does not fit onto the juicer Lever is in the OPEN position.
body
The juice collector bowl
vibrates when the juice is
being extracted
Before fitting the bowl onto
the juicer body make sure
that the lever is in the
CLOSE position.
Hard ingredients (carrots, chicory, A slight vibration is normal,
especially when processing
beetroot, etc.)
hard ingredients.
If the problem has not been
resolved or in the case of other
types of fault, contact your local
technical support centre.
36
Solution
Download PDF