Hot Cabinets
FL-2334
Rev. 1 (1/07)
Page 1 of 4
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
for H135WUA11 Hot Cabinet (Aluminum)
H135WSUA11 Hot Cabinet (Stainless Steel)
Model No.
Volts
Watts
Amps
Hertz
Phase
NEMA
H135WUA11
H135WSUA11
120
1920
16
60
1
5-20P
H135WUA11208
H135WSUA11208
208
2000
9.6
60
1
6-15P
H135WUA11240
H135WSUA11240
240
2000
8.6
60
1
6-15P
All are designed for AC service. The above model numbers may be followed by “M”, “L”, “D”, “R”
and ending with “S” or “Z”.
HOW TO INSTALL UNIT:
1. Place cabinet near warm ovens. Do NOT place
cabinet in drafty areas or near ventilating systems.
2. Plug end into proper wall outlet.
Use of treated or
soft water may be
required for proper
operation and to maintain warranty.
3. Fill with 2 qts.(1.8 liters) of clean, hot water.
HOW TO PROOF:
1. Fill water pan (See “How to Install”)
2. Push “POWER” switch to “ON.” The yellow light
will come on.
3. Push “MODE SELECTION” switch to “PROOF”.
The yellow light will come on.
4. Turn “HUMIDITY” dial to No. 8.
5. Turn “AIR” dial to “OFF.”
6. Preheat for 30 minutes. “
7. Put fresh or fully thawed dough into cabinet.
NOTE: The cabinet temperature will drop temperature inside cabinet if cold dough is added.
Do NOT put frozen dough into cabinet
CONTROL PANEL PARTS IDENTIFICATION
1. Switch-Power
2. Yellow Light-Power
3. Thermostat-Humidity
4. Thermostat-Air
5. Yellow Light-Proof
6. Red Light-Heat
7. Switch-Mode Selection
8. Thermometer
NOTE: No. 8 setting will give you an approximate
temperature of 95°F (35°C), and 90-95%
humidity. Experiment with different “HUMIDITY” and “AIR” settings to get the exact
temperature and humidity you need. The
thermometer shows the temperature inside
the cabinet.
NOTE: Check water level in water pan if you are
proofing longer than 90 minutes. Fill with
clean, hot water.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Hot Cabinets
FL-2334
Rev. 1 (1/07)
Page 2 of 4
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
for H135WUA11 Series Hot Cabinet
HOW TO HOLD
1. Push “POWER” switch to “ON.” The yellow light
will come on.
2. Push “MODE SELECTION” switch to “HEAT.”
The red light will come on.
3. Turn “AIR” dial to temperature needed.
MAINTENANCE:
NOTE: No.8 is about 175°F (79°C).
No.6 is about 165°F (74°C).
Proper food holding temperature
is 140°F (60°C) or higher.
4. Preheat cabinet for 30 minutes.
5. Put food into cabinet.
HOW TO TURN UNIT OFF:
Push “POWER” switch to “OFF” position.
BEFORE CLEANING THE CABINET:
1. Allow cabinet to cool.
2. Remove Hot Unit from cabinet.
3. Do NOT use abrasives or harsh chemicals.
HOT UNIT REMOVAL INSTRUCTIONS:
1. Unplug power cord from wall outlet.
2. Pull entire unit out the front of the cabinet.
Cleaning Notes:
1. Wipe up spills as soon as possible.
2. Clean cabinet regularly to avoid heavy dirt build-up.
3. Make a test spot with cleaner.
4. Follow manufacturer’s directions on cleaner.
5. Do not mix cleaners.
6. Avoid drips and splashes.
7. Empty water pan at least once a week.
DELIME OR DESCALE RESERVOIR PARTS AS
REQUIRED TO PREVENT DAMAGING BUILD-UP.
WARRANTY COVERAGE MAY BE AFFECTED WITHOUT PROPER CLEANING.
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Hot Cabinets
FL-2334
Rev. 1 (1/07)
Page 3 of 4
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
for H135WUA11 Hot Cabinet (Aluminum)
H135WSUA11 Hot Cabinet (Stainless Steel)
HOW TO CLEAN UNIT:
Soil
DOORS
Vinyl (Out)
Aluminum (In)
Dirt, Grease and Oil
Mild Detergent* and water.
Mild detergent* and hot water, or
mild abrasive cleaner.
Dirt
CABINETS
(H137WUA11 is
Aluminum)
(H137WSUA11
is
Stainless Steel)
Cleaner
Water Spots
1. Use soft, damp cloth.
2. Rinse with hot water.
3. Wipe dry.
Chemical oven cleaner for cabinet
material
1. Rinse after steam cleaning.
2. Wipe dry.
Follow oven cleaner manufacturer’s
directions
Mild abrasive cleaner; oily or waxy
cleaner
Mild abrasive cleaner.
Oily or waxy cleaner.
Apply with clean, soft cloth. Wipe with
damp cloth.
Apply with soft, clean cloth.
Wipe with damp cloth.
Steam (No strong alkaline additive)
Fingerprints, Grease
and Oil
Method
1. Wipe with soft, damp cloth.
2. Rinse well.
*Mild detergents include soaps and non-abrasive cleaners.
TROUBLE-SHOOTING CHART:
FAILURE
POSSIBLE CAUSE
1. Indicator lights do NOT light.
2. Unit does not heat
3. Unit gets too hot or won’t shut off
4. Humidity is low.
5. Blower does not work or makes noise.
1a. Circuit breaker/fuse to wall outlet blown.
2a. Cord unplugged from wall outlet or cabinet.
3a. Switch is “OFF.”
2a. Thermostats set too low or are off.
2b. Switch is “OFF.”
3a. Defective electrical parts.
3b. UNPLUG UNIT FROM WALL OUTLET
4a. Water in pan may be low
4b. Thermostat set too low
5a. Defective Blower
NOTE: Optional digital thermometer will flash if cabinet temperature is below 140°F or above 250°F.
Call the Factory if you need different settings.
If cause is none of the above, refer to our list of Authorized Service Centers, FL-1400.
CABINET REPLACEMENT PARTS
Door, Silver..........................1200-495-BL
Door, Red.............................1200-499-BL
Door Gasket.........................0861-259
Door Hinge.......................... 0519-104
Door Latch...........................1006-154-01
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
Hot Cabinets
FL-2334
Rev. 1 (1/07)
Page 4 of 4
5925 Heisley Road • Mentor, OH 44060-1833
OPERATING and MAINTENANCE INSTRUCTIONS
for H135WUA11 Series Hot Cabinet
REPLACEMENT PARTS:
DESCRIPTION
Hot Unit (135WUA11)
Hot Unit (135WSUA11)
Heater (Reservoir)
Pan (Reservoir)
Heater (Air)
Thermostat Kit
Thermometer Kit (Analog)
Power Cord
Proof & Heat Lights
Power Light
Switch (Power)
Switch (Mode Selection)
Blower Kit
Drip Pan Kit
120 VOLT
PHU-747-071
PHU-747-080
0811-285
1017-097
0811-214
0848-062-K
5238-030-K
0810-065-1
0766-093
0766-094
0808-116
0808-117
0769-180-K
1017-058
208 VOLT
PHU-747-072
PHU-747-081
0811-286
1017-097
0811-250
0848-062-K
5238-030-K
0810-039
0766-093-1
0766-095
0808-116
0808-117
0769-182-K
1017-058
240 VOLT
PHU-747-073
PHU-747-082
0811-287
1017-097
0811-215
0848-062-K
5238-030-K
0810-039
0766-093-1
0766-095
0808-116
0808-117
0769-182-K
1017-058
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com