200703078--Envirosense owners manual.qxd

Owner’s Manual
EnviroSense Environmental Sensor
™
Español……1
Installation
The EnviroSense environmental sensor relays ambient temperature and humidity readings to a Tripp Lite SNMP accessory card (Model: SNMPWEBCARD or SNMPCARD) installed in a compatible UPS or PDU.
The sensor can also send and receive contact closure signals, communicating with up to four compatible devices (such as smoke detectors, fire alarms and security systems).
Connecting the EnviroSense Sensor to an SNMP Accessory Card
• Plug the EnviroSense sensor's PS/2 connector (Figure 1) into the SNMP accessory card's PS/2 port. Refer to the SNMP accessory card (or PDU)
documentation to locate this port.
• If the SNMP accessory card has already been configured for the network, it must be rebooted before it will recognize the EnviroSense sensor.
After connecting the sensor, use a Web browser to connect to http://x.x.x.x/admin.htm (replace x.x.x.x with the card's IP address). Log in to
PowerAlert as the administrator. Click the button labeled Reset/Reboot SNMP Card (Figure 2). After the card reboots, a new button labeled
Probe will appear in the top navigation area of PowerAlert. Click this button to access monitoring and control options for the EnviroSense sensor.
Contact Closure Connection (Optional)
The EnviroSense sensor supports up to four contact closure connections (Figure 3). Pin 1 is the Common connection. The other four connections
are labeled Smoke, Fire, Water and Security for convenience, but each of them can connect with any type of contact closure device.
Figure 1: EnviroSense PS/2 Connector
Specifications
Cable Length: 12 feet (3.66 meters)
Temperature Measurement Range: 32° to 149° F (0° to 65° C)
Temperature Measurement Accuracy: ± 8% from 59° to 95° F (15° to 35° C)
Humidity Measurement Range:10% to 90%
Humidity Measurement Accuracy: ± 2%
Power Dissipation: < 400 mW
Warranty and Warranty Registration
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 2 years
from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion. Service under this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid) to: Tripp Lite, 1111
W. 35th Street, Chicago, IL 60609, USA. Seller will pay return shipping charges.
Figure 2: PowerAlert Administration Screen
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES
NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow
limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.)
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
WARRANTY REGISTRATION
Figure 3: EnviroSense Contact Closure
Connections
FCC Notice: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors with this product. Any changes or modifications to this product not expressly approved
by the party responsible for compliance could void the user's authority to operate the equipment.
Regulatory Compliance Identification Numbers: For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all
required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.
Tripp Lite follows a policy of continuous improvement. Specifications are subject to change without notice.
Copyright © 2007 Tripp Lite. All rights reserved. EnviroSense is a trademark of Tripp Lite.
Download PDF