VITODENS 200® Operating Instructions &

Please file in Service Binder
Operating Instructions &
User’s Information Manual

Vitodens 200-W
WB2B Series
Wall-mounted, gas-fired condensing boiler
For natural gas and liquid propane gas
Heating input
31 to 370 MBH
9 to 105 kW
VITODENS 200

WARNING
If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable
liquids in the vicinity of this or any other
appliance.
IMPORTANT
Read and save these instructions
for future reference.
WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliances.
Do not touch any electrical switches, do not
use any phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
WARNING
Improper installation, adjustment, and/or
operation could cause carbon monoxide
poisoning resulting in injury or loss of life.
This product must be installed and serviced by
a professional service technician who is
experienced and qualified in hot water boiler
installation and gas combustion.
5369 299 v1.1
09/2010
 This trademark is registered with the U.S. Patent and Trademark Office.
Safety, Installation and Warranty Requirements
Safety, Installation and Warranty Requirements
Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the instructions
listed below and details printed in this manual can cause product/property damage, severe personal injury, and/or loss of life. Ensure
all requirements below are understood and fulfilled (including detailed information found in the manual subsections).
H Licensed professional heating
contractor
The installation, service, and
maintenance of this equipment must
be performed by a licensed
professional heating contractor.
"
Please see section
entitled “Important
Regulatory and
Installation
Requirements” in the
Installation Instructions.
H Product documentation
Read all applicable documentation
before commencing installation. Store
documentation near boiler in a readily
accessible location for reference in the
future by service personnel.
H Carbon monoxide
Improper installation, service and/or
maintenance can cause flue products
to flow into living space. Flue
products contain poisonous carbon
monoxide gas.
H Equipment venting
Never operate boiler without an
installed venting system. An improper
venting system can cause carbon
monoxide poisoning.
"
For information
pertaining to the proper
installation, service and
maintenance of this
equipment to avoid
formation of carbon monoxide, please
see the Installation Instructions of the
Vitodens 200-W Direct Vent System.
H Warranty
Information contained in
this and related product
documentation must be
read and followed. Failure
to do so renders warranty
null and void.
WARNING
Installers must follow local
regulations with respect to
installation of carbon monoxide
detectors. Follow manufacturer’s
maintenance schedule of boiler.
"
For a listing of
applicable literature,
please see section
entitled “Important
Regulatory and
Installation Requirements”
in the Installation Instructions.
5369 299 v1.1
H Advice to owner
Once the installation work is
complete, the heating contractor must
familiarize the system
operator/ultimate owner with all
equipment, as well as safety
precautions/requirements, shut-down
procedure, and the need for
professional service annually before
the heating season begins.
2
Table of Contents
Page
General Information / Safety
About these Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Safety
For your Safety
........................................................................
5
Inform Yourself
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Your Vitodens 200-W Boiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
...............................
10
Overview of Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Opening the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vitotronic 200 Type HO1 Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heating system with two heating circuits . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
14
Your System is Preset at the Factory
Start-up / Shutdown
Adjusting the Room
Temperature
Starting the Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
16
16
Shutting Down the Heating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a heating circuit and DHW heating . . . . . . . . . . . . . . . . . . . .
Shutting down a heating circuit and stopping
DHW heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting DHW heating only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stopping DHW heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
17
Setting a Permanent Room Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting normal room temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a reduced room temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a time program (switching times) . . . . . . . . . . . . . . . . . . . .
Changing the room temperature for a few days only . . .
Selecting the holiday program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
18
19
20
21
22
Changing the Room Temperature for a
Few Hours Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting energy saving mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Selecting party mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Selecting DHW Heating
Selecting Constant DHW Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHW temperature setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a time program (switching times) . . . . . . . . . . . . . . . . . . . . .
Selecting automatic mode (if required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up an individual time program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
26
26
27
Selecting DHW Heating for a Few Hours Only . . . . . . . . . . . . . . . 29
Selecting DHW heating only once . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Further Adjustments
5369 299 v1.1
Scanning Options
Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the display contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
31
31
31
Scanning Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Order in which temperatures and operating
conditions can be scanned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Scanning Time Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central heating time program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHW time program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning fault display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
33
33
34
3
Table of Contents
Other Settings
Service Instructions
How to Save Energy
35
35
35
36
36
36
36
36
36
37
37
37
37
37
Service Instructions for Your Heating System . . . . . . . . . . . . . . . . . 38
How to Save Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
... by heating correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
... with regular maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
... with effective insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
39
39
Lighting and Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5369 299 v1.1
Additional Information
Changing the Heating Pattern of the Boiler . . . . . . . . . . . . . . . . . . . . . .
Rooms are too cold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rooms are too hot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
There is no hot water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The DHW is too hot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
”Select htg. circuit” flashes in the display . . . . . . . . . . . . . . . . . . . . . .
”Fault” flashes in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The time flashes in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“Service” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
”Remote control” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
”Ext. control” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
”Ext. program” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“Ext, room t. setpt.” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
“Without function.” is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
General Information/Safety
About these Instructions
Take note of all symbols and notations intended to draw attention to potential hazards or important product information.
These include ”WARNING”, ”CAUTION”, and ”IMPORTANT”. See below.
WARNING
Indicates an imminently hazardous
situation which, if not avoided, could
result in death, serious injury or
substantial product/property damage.
CAUTION
Indicates an imminently hazardous
situation which, if not avoided, may
result in minor injury or
product/property damage.
IMPORTANT
Warnings draw your attention to the
presence of potential hazards or
important product information.
Cautions draw your attention to the
presence of potential hazards or
important product information.
Helpful hints for installation, operation
or maintenance which pertain to the
product.
This symbol indicates that additional,
pertinent information is to be found in
column three.
This symbol indicates that other
instructions must be referenced.
For your Safety
H Operation
Before operating the boiler, make sure
you fully understand its method of
operation. Your heating contractor
should always perform the initial start-up
and explain the system. Any warranty is
null and void if these instructions are not
followed.
H Flue gas smell
5369 299 v1.1
- Deactivate heating equipment.
- Open windows and doors.
- Inform your heating contractor.
H Working on the equipment
All personnel working on the equipment
or the heating system must have the
proper qualifications and hold all
necessary licenses.
Ensure main power to equipment,
heating system, and all external controls
has been deactivated. Close main gas
supply valve. Take precautions in all
instances to avoid accidental activation
of power during service work.
H Dangerous conditions
- Deactivate main power immediately.
- Close gas supply valve.
H Maintenance and cleaning
Regular inspection and service by a
qualified heating contractor is important
to the performance of the Viessmann
Vitodens 200-W. Neglected
maintenance impacts on warranty;
regular inspection ensures clean,
environmentally friendly and efficient
operation. We recommend a
maintenance contract with a qualified
heating contractor.
H Technical information
Literature applicable to all aspects of the
Vitodens 200-W:
- Technical Data Manual
- Installation Instructions
- Start-up/Service Instructions
- Operating Instructions
and User’s Information Manual
Additional applicable literature:
- Accessory manuals
5
Safety
For your Safety (continued)
H Carbon monoxide
The U.S. Consumer Product Safety
Commission strongly recommends the
installation of carbon monoxide
detectors in buildings in which
gas-burning equipment is installed.
Carbon monoxide (CO) is a colorless,
odorless gas, which may be produced
during incomplete combustion of fuel
and/or when the flame does not receive
an adequate supply of combustion air.
Carbon monoxide can cause severe
personal injury or loss of life.
Therefore, carbon monoxide detectors
that are in compliance with a nationally
recognized standard (e.g. ANSI/UL
2034-2002, CSA 6.19-01) should be
installed and maintained in buildings that
contain gas-burning equipment.
Note:
Viessmann does not test any detectors
and makes no representation regarding
any brand or type of detector.
H For safe operation
We recommend that you frequently:
- Check for debris which could obstruct
the flow of flue gases. The vent or
chimney must not be blocked. A
blocked or partially blocked vent or
chimney can cause flue gases to leak
into the structure. Flue gases leaking
into the house can cause injury or
death. Blocked or partially blocked
chimneys must have the blockage
removed by a qualified heating
contractor.
- Check pressure gage for correct
system (water) pressure. Check for
water on the floor from the discharge
pipe of the pressure relief valve or any
other pipe, pipe joint, valve or air
vent.
- Check for moisture, water, or
appearance of rust on the flue gas
pipes, their joints as well as vent
dampers, or side wall vent terminals
(if so equipped).
- Ensure that nothing is obstructing the
flow of combustion and ventilation air
and no chemicals, garbage, gasoline,
combustible materials, flammable
vapors and liquids are stored (not
even temporarily) in the vicinity of the
boiler.
- Do not allow unsupervised children
near the boiler.
WARNING
As there are no user-serviceable parts
on the boiler, burner or control, the
end-user must not perform service
activities or adjustments of any kind on
system components. Failure to heed
this warning can cause property
damage, severe personal injury, or loss
of life.
WARNING
Improper installation, adjustment,
service, or maintenance can cause flue
products to flow into living space. Flue
products contain poisonous carbon
monoxide gas which can cause nausea
or asphyxiation resulting in severe
personal injury or loss of life.
CAUTION
Should overheating occur or the gas
supply fail to shut off, do not
disconnect the electrical supply to the
pump. Instead, shut off the gas supply
at a location external to the appliance.
WARNING
Service/inspection of the boiler and the
system is recommended once a year.
Maintenance, service and cleaning are
specified in the Installation Instructions.
Before the heating season begins, it is
recommended that the boiler and burner
be serviced by a qualified heating
contractor. Service contracts may be
established through gas suppliers or
other licensed contractors in your area.
The operator/ultimate owner is required
to have the heating boiler, burners, and
controls checked, as a minimum once
per year, by the original installer or by a
competent heating contractor familiar
with the equipment. Defects must be
corrected immediately.
CAUTION
5369 299 v1.1
Do not use this boiler if any part has
been under water. Immediately call a
qualified heating contractor to inspect
the boiler and to replace any part of the
control system and any gas control
which has been under water.
6
Safety
For your Safety (continued)
Frozen water pipe hazard
If your home will be unattended for an
extended period of time during cold
weather, you should...
WARNING
Failure to protect against frozen pipes
could result in burst water pipes,
serious property damage and/or
personal injury. Boiler may shut down.
Do not leave your home unattended for
long periods of time during freezing
weather conditions without turning off
the water supply and draining water
pipes or otherwise protecting against
the risk of frozen pipes.
Your heating boiler is designed to provide
a warm and comfortable living
environment. It is not designed to ensure
against freezing of water pipes.
The boiler is equipped with several safety
devices that are designed to shut down
the boiler and to prevent it from restarting
in the event of various unsafe conditions.
H Shut off the water supply to the
building, drain the water pipes and add
an antifreeze for potable water to drain
traps and toilet tanks. Open faucets
where appropriate.
Or..
H Have someone check the building
frequently during cold weather and call a
qualified service agency if required.
Or...
H Install a reliable remote temperature
sensor that will notify somebody of
freezing conditions within the home.
5369 299 v1.1
If your boiler remains off for an extended
period of time during cold weather, water
pipes may freeze and burst, resulting in
extensive water damage and conditions in
which mold could grow. Certain molds are
known to cause respiratory problems, as
well as to pose other serious health risks.
In case of water damage, immediate
measures should be taken to dry out
affected areas as quickly as possible to
prevent mold from developing.
7
Safety
For your Safety (continued)
If you notice fire coming from the
appliance, call the fire department
immediately! Do not attempt to extinguish
the fire unless qualified to do so.
WARNING
Fire causes a risk of burns and
explosion!
H Shut down the boiler
H Close fuel shut-off valves
H Use a tested fire extinguisher, class
ABC.
Installation area conditions
WARNING
Incorrect ambient conditions can lead to
damage to the heating system and put
safe operation at risk.
H Ensure ambient temperatures are higher
than 32°F / 0°C and lower than
104°F / 40°C.
H Prevent the air from becoming
contaminated by halogenated
hydrocarbons (e.g. as contained in paint
solvents or cleaning fluids) and
excessive dust (e.g. through grinding or
polishing work).
Combustion air for the heating process,
and ventilation of the boiler room must
be free of corrosive contaminants. To
that end, any boiler must be installed in
an area that has no chemical exposure.
The list to the right indicates the main,
currently known sources.
H Avoid continuously high levels of
humidity (e.g. through frequent drying of
laundry).
H Never close existing ventilation
openings.
Replacement components, spare and wear
parts
IMPORTANT
Areas likely to contain contaminants:
H New building construction
H Swimming pools
H Remodelling areas, hobby rooms
H Garages with workshops
H Furniture refinishing areas
H Dry cleaning/laundry areas and
establishments
H Auto body shops
H Refrigeration repair shops
H Metal fabrication plants
H Plastic manufacturing plants
H Photo processing plants
H Beauty salons
Products containing contaminants:
H Chlorine-type bleaches, detergents and
cleaning solvents found in household
laundry rooms
H Paint and varnish removers
H Hydrochloric acid, muriatic acid
H Chlorine-based swimming pool chemicals
H Spray cans containing
chlorofluorocarbons
H Chlorinated waxes and cleaners
H Cements and glues
H Refrigerant leaks
H Calcium chloride used for thawing
H Sodium chloride used for water
softening salt
H Permanent wave solutions
H Adhesives used to fasten building
products and other similar items
H Antistatic fabric softeners used in
clothes dryers
5369 299 v1.1
Components which are not tested with
the heating system may damage the
heating system, or affect its functions.
Installation or replacement may only be
carried out by a qualified heating
contractor.
Sources of combustion and ventilation air
contaminants
8
Inform Yourself
Getting Started...
The timer of the control unit switches between ”normal room temperature” and
”reduced room temperature” at the required times.
1. Normal room temperature
for the times you spend at home and
require a comfortably warm room
temperature (e.g. 68ºF / 20ºC).
2. Reduced room temperature
for the times you are away from
home. To save energy,
a lower temperature is typically
selected (e.g. 57ºF / 14ºC).
Times and duration of the two room
temperatures can be set on the
programming unit of your control.
The temperature settings for both the
”normal room temperature” and
”reduced room temperature” can be
set according to your personal
preference.
The timer of the control unit switches domestic hot water production on and off at
the required times.
1. Domestic hot water heating can be
set to take place
during the times you spend at home
and require hot water for your daily
DHW requirements (e.g. for
showering).
Times and duration of the domestic hot
water production period can be set on
the programming unit of your control.
2. Domestic hot water heating can be
set not to take place
for the times you spend sleeping, for
example.
The domestic hot water recirculation
pump (if installed) ensures that
domestic hot water is readily available
when domestic hot water is drawn.
5369 299 v1.1
You may select a DHW temperature
setting based on your personal
preference of up to 140ºF / 60ºC.
9
Inform Yourself
Your Vitodens 200-W Boiler
Please ask your heating contractor to check off the appropriate box ( ).
j Vitodens 200-W
without domestic hot water tank
The control unit activates and
deactivates space heating and
supplies rooms with heat.
j Vitodens 200-W
with separate domestic hot water
tank
Domestic hot water heating has
priority over space heating. The
control unit switches automatically to
space heating when the preset
domestic hot water temperature is
reached.
Your System is Preset at the Factory
The control unit is preset at the factory
for standard operation. Your heating
system is therefore ready to use:
H Between 06:00 and 22:00 hrs. the
system provides central heating with
standard room temperature.
H DHW will be heated between 05:30
and 22:00 hrs. DHW will be heated to
the set temperature subject to a DHW
tank being installed. The DHW
circulation pump is switched ON (if
connected to the control unit).
H Between 22:00 and 06:00 hrs. the
system provides central heating with
the reduced room temperature (set to
3ºC, frost protection).
H Between 22:00 and 05:30 hrs. the
DHW tank temperature will not be
boosted. The DHW circulation pump is
switched OFF (if connected to the
control unit).
H The system automatically changes
over between summer and winter
time.
You may change the factory settings in
accordance with personal requirements.
5369 299 v1.1
Note:
All data is saved in case of power
failure.
Press button ”D” to reset the
switching times to their factory
default settings.
Please note that this will reset all
altered values to their original factory
default setting.
10
Inform Yourself
Overview of Controls and Indicators
You can change all settings for your heating system, centrally, at the control unit. You may also make such adjustments for
the respective heating circuits at the remote control unit, if your system is equipped with such a unit.
See the remote control
operating instructions.
Opening the control unit
Lift cover A and pivot control unit flap
B down. All boiler controls are located
behind the control unit flap.
B
A
5369 299 v1.1
A Cover
B Control unit flap (open to make
adjustments)
11
Inform Yourself
Overview of Controls and Indicators
(continued)
Vitotronic 200 Type HO1 Functions
D EFG
H
Boiler temp.
140
MO
s
ºF
A
+
C
B
+
A
OK
_
T
S
R
O
N
M
L
K
L Party mode ON / OFF
M Factory default settings button
N Confirmation button
O Adjustment buttons
P DHW temperature
R Emission test function (only for
heating engineers)
S Reduced room temperature
T Time / date
5369 299 v1.1
A Time program for central heating
B Time program for DHW heating
C Holiday program
D Information
E Standby mode
F DHW only
G Central heating and DHW
H Normal room temperature
K Energy saving mode ON / OFF
P
12
Inform Yourself
Overview of Controls and Indicators
A
B
C
D
E
Boiler temp.
2
1
3
?F
140
Mo
0
(continued)
4
A
s
+
RESET
+
OK
?
A Pressure gauge
B Fault display (red)
C Operating status display (green)
D Reset button
E ON / OFF switch
Boiler temp.
1 Mo
8 8 :8 8 :8 8
esmp(wp
ºCF S
hu
upA
These symbols are not always displayed, but appear subject to the system version and the operating state.
e
s
p
A
u
S
E
1
DHW heating via solar heating
system (accessories)
Burner ON
Time adjustment display
Emissions test ON
Burner fault (appears instead of
the day of the week)
In case of two heating circuits:
Selected heating circuit
5369 299 v1.1
Risk of freezing
Central heating with normal
room temperature
m
Central heating with reduced
room temperature
m/sp Heating circuit pump ON
|
Mixing valve “OPEN”
~
Mixing valve “CLOSED”
w
DHW heating enabled
wp
DHW pump ON
13
Inform Yourself
Overview of Controls and Indicators
(continued)
Heating system with two heating circuits
When two heating circuits have been
connected to your heating system,
select the heating circuit to which the
setting should apply before making
adjustments at the control unit.
Press the following keys:
1. ⊕ “1r
r“ flashes on the display.
2.
for selecting heating circuit A1
(heating circuit without mixing
valve).
Note:
“Select heating circuit” will be displayed
should you begin making adjustments
prior to selecting the relevant heating
circuit.
Or..
3. ⊕ for heating circuit M2 (heating
circuit with mixing valve)
“2r
r“ flashes on the display.
4.
Boiler temp.
2Mo
e mp w
150
A
ºF
for selecting heating circuit M2
(heating circuit mixing valve).
Note:
After approximately 4 seconds or if you
press
again, the following will be
displayed:
The figure in front of the day indicates
which heating circuit has been selected.
Note:
If “Remote control” flashes in the
display, make the relevant adjustment
at the remote control.
See the remote control
operating instructions.
5369 299 v1.1
5. Continue with the required
adjustment (e.g. activate rotary
selector “ts“ or press the
appropriate key for the relevant
function).
14
Start-up / Shutdown
Starting the Heating System
A
Kesseltemperatur
2
1
3
0
1. Check the pressure of the heating
system on the pressure gauge A: If
the pressure is below 12 psi / 0.8 bar
the system pressure is too low.
Notify your heating contractor if the
system pressure is too low.
?C
Mo
4
+
+
OK
?
B
2. For room air dependent operation:
Check whether the ventilation
apertures in the boiler room are open
and unobstructed.
Note:
For room air dependent operation:
This boiler requires fresh air for safe
operation. The boiler must be vented
and supplied with air and exhaust
vents.
3. Open gas shut-off valve B.
C
4. Switch ON the power supply, (e.g. at
the breaker or electrical disconnect
switch. Energize power / pump
module).
5369 299 v1.1
5. Switch ON the heating system ON /
OFF switch “8” C; the operating
status is indicated (ON indicator) by
the green LED and the boiler water
temperature will appear in the
display.
15
Start-up / Shutdown
Shutting Down the Heating System
If you do not want to use your heating
system temporarily, (e.g. during your
summer holidays), switch to stand-by
operation (see ”Shutting down a heating
circuit and stopping DHW heating”).
Note:
The circulation pumps are briefly started
every 24 hours to prevent them from
seizing up.
If you do not want to use your heating
system for a long period (several
months), you should shut down the
system.
We advise you to contact your heating
contractor before shutting down the
heating system for long periods. Your
heating contractor will take any
necessary action, (e.g. for frost
protection of the system or to safeguard
the heat exchanger surfaces).
1. Switch the main ON / OFF switch
“8” OFF.
2. Close the gas shut-off valve.
3. Turn off the power supply switch or
disconnect power / pump module.
The power supply to the system is
now switched off.
There is no frost protection.
Note:
All control settings are retained.
Starting a heating circuit and DHW heating
You want to heat your rooms and have
DHW available.
Press “r
rw“ for “Heating & DHW”.
If “Select heating circuit” is displayed
and “1r
r“ flashes:
H Select that heating circuit with ⊕ / ,
to which the adjustment should apply.
H Confirm twice with
.
Press “r
rw“ for “Heating & DHW”
again.
16
Note:
“r
rw“ button illuminates:
H Symbol ”s” appears during central
heating with normal room
temperature.
H Symbol “m” appears during central
heating with a reduced room
temperature above 37ºF / 3ºC.
5369 299 v1.1
H Central heating will be provided with
normal or reduced room temperature
(frost protection) according to the set
time program. Standard setting: from
06:00 to 22:00 hrs. with the normal
room temperature, otherwise with the
reduced room temperature.
H DHW heating (if a DHW tank or
instantaneous water heater is
installed) and DHW circulation pump
running (if connected to the control
unit) according to the selected time
program. Standard setting: from
05:30 to 22:00 hrs., DHW is heated
to the selected set temperature and
the DHW circulation pump is switched
ON.
H Frost protection for the boiler and the
DHW tank is enabled.
Start-up / Shutdown
Shutting Down the Heating System
(continued)
Shutting down a heating circuit and stopping DHW heating
You do not want to heat your rooms or
have DHW available.
Press “9“ for “Standby mode”.
Note:
The circulation pump is briefly started
every 24 hours to prevent it from
seizing up.
If “Select heating circuit” is displayed
and “1r
r“ flashes:
H Select the heating circuit with ⊕ / ,
to which the adjustment should apply.
H Confirm twice with
.
H Press “9“ again for “Standby mode”.
Standby mode:
H Central heating is disabled for the
selected heating circuit.
H No DHW heating.
H Frost protection for the boiler and the
DHW tank is enabled.
Starting DHW heating only
You do not want to heat your rooms but
have DHW available.
Press “w“ for “DHW only”.
Note:
If “w“ is illuminated and DHW heating
is enabled in accordance with the
selected time program, then “w“ will be
displayed.
If “Select heating circuit” is displayed
and “1r
r“ flashes:
H Select the heating circuit with ⊕ / ,
to which the adjustment should apply.
H Confirm twice with
.
Press “w“ for “DHW only” again.
H Central heating is disabled for the
selected heating circuit.
H DHW heating (if a DHW tank is
installed) and DHW circulation pump
(if connected to the control unit) ON
according to the set time program.
Standard setting: from 05:30 to
22:00 hrs., DHW is heated to the
selected set temperature and the
DHW circulation pump is switched
ON.
H Frost protection for the boiler and the
DHW tank is enabled.
5369 299 v1.1
Stopping DHW heating
You want to heat your rooms but
not make DHW available. Set the DHW
temperature to 50ºF / 10ºC
(see page 25).
17
Adjusting the Room Temperature
Setting a Permanent Room Temperature
Observe the following points if your
heating circuit should provide central
heating.
H “Heating & DHW” “r
rw” must be
illuminated, otherwise press “r
rw”.
If “Select heating circuit” is displayed
and “1r
r“ flashes:,
- Select the heating circuit with ⊕ / ,
to which the central heating should
apply.
- Confirm twice with
.
- If “r
rw” does not illuminate, press
“r
rw” again.
H You can select the normal room
temperature “ts“ (for day) and the
reduced room temperature (for night)
with “tm”.
H The timing of when your heating
circuit operates to provide central
heating with normal or reduced room
temperature depends on the settings
of the time program (see page 20).
- If no time phases are selected, central
heating will be enabled for the whole
day at reduced room temperature.
- If one or more time phases are
selected, central heating will be
enabled for those times with normal
room temperature.
You can scan the time program, (see
page 33).
For changing the time program, (see
page 20).
Selecting normal room temperature
Select the required temperature for the
“Normal room temp.” with selector dial
“ts”.
Normal room temp.
ºF
68
s
+
5369 299 v1.1
If “Select htg. circuit” is displayed and
“1r
r” flashes:
H Select the heating circuit with ⊕ / ,
to which the central heating should
apply.
H Confirm twice with
.
H Set the required temperature for
“Normal room temp.” with selector dial
“ts”.
18
Adjusting the Room Temperature
Setting a Permanent Room Temperature
(continued)
Selecting a reduced room temperature
Press the following buttons:
1. tm for “Red. room temp.”, the
current temperature will flash.
Note:
When setting the reduced room
temperature to 37ºF / 3ºC, “Frost
protection” will be displayed.
If “Select htg. circuit” is
displayed and “1r
r“ flashes:
H Select the heating circuit
with ⊕ / , to which the
central heating should apply.
H Confirm twice with
.
H tm again for the “Red. room
temp.”, the current
temperature selection will
flash.
Red. room temp.
57ºF
m
2. ⊕/ for the required temperature.
3.
to exit the setting menu.
5369 299 v1.1
4.
If “Select htg. circuit” is
displayed and “1r
r“ flashes:
to confirm; the temperature no
longer flashes and is saved.
19
Adjusting the Room Temperature
Setting a Permanent Room Temperature
(continued)
Selecting a time program (switching times)
For central heating, up to four changes can be made between normal and reduced
room temperature (four time phases). At the factory, time phase 1 is set for every
day from 06:00 to 22:00 hrs., ie. during that time, all rooms are heated to the
normal room temperature. You can set the time programs the same for every day or
for each day of the week individually.
When setting time programs, bear in mind that your heating system requires some
time to heat the rooms to the required temperature.
For a sequence of steps to delete a time phase, (see page 21).
Steps for selecting a time program:
Press the following keys:
1. ur
r for “Htg. time program”.
If “Select htg. circuit” is
displayed and “1r
r“ flashes:
H Select the heating circuit
with ⊕ / , to which the
central heating should apply.
.
H Confirm twice with
H “ur
r” again for the
“Heating time program”.
Central heating time prog.
1-7
Note:
If you want to terminate the time
programming early, press “ur
r“again
and confirm with
.
2. ⊕/ until “1-7” is displayed, if you
want to set up identical time
phases for every day.
Or..
Central heating time prog.
Mo
3. ⊕/ until “Mo”, “Tu” etc. is
displayed, if you want to set up
different time phases for the
day displayed.
4.
to confirm; “Htg. timer 1”
will then be displayed.
5.
to confirm; “Htg. cycle 1 On”
will then be displayed.
Note:
If different time phases are set for
individual days and you want to return
to identical time phases for every day,
press
when “1-7” is displayed. All
time phases are returned to their original
condition.
Note:
Press
phase.
if you want to skip a time
6. ⊕/ for the heating phase starting
point.
7.
to confirm; “Htg. cycle 1 Off”
will then be displayed.
8. ⊕/ for the heating phase end point.
to confirm; “Htg. cycle 2 On”
will then be displayed.
10. Proceed for adjusting the start and
end of heating phases 2 to 4 as
described under steps 6 to 8.
20
5369 299 v1.1
9.
Adjusting the Room Temperature
Setting a Permanent Room Temperature
(continued)
Selecting a time program (switching times) (continued)
Press the following buttons if you want
to delete a time phase:
1. ur
r for “Htg. time program”.
If “Select htg. circuit” is
displayed and “1r
r“ flashes:
H Select the heating circuit
with ⊕ / , to which the
central heating should apply.
H Confirm twice with
.
H “ur
r” again for the
“Heating time program”.
2.
Heating phase 2 OFF
1-7
until the required “Htg. cycle 1
Off” is displayed.
3. ⊕/ until “ - - : - -” is displayed for
the end time.
--:-4.
to confirm; until the boiler
water temperature is displayed.
Changing the room temperature for a few days only
The following energy saving options are
available for times, when you are not at
home:
H You can completely shut down central
heating by pressing 9 (standby
mode).
Or..
5369 299 v1.1
H You can set the central heating to
minimum energy consumption (e.g. to
prevent house-plants from suffering
through cold). For this, select the
“Holiday program” j.
During the holiday program, all heating
circuits are heated with the selected
“Red. room temp.”, but there will be
no DHW heating.
21
Adjusting the Room Temperature
Setting a Permanent Room Temperature
(continued)
Selecting the holiday program
The selected time program will be
enabled at the departure and return
days.
Press the following keys:
1. j
for “Holiday program”.
Or..
Departure date
Sa
2.
for “Departure date” (the
current date is displayed).
3. ⊕
for the date of the required
departure day.
4.
to confirm; “Return date”(a
date following that of the
departure day) will be
displayed.
5. ⊕
for the date of the required
return day.
6.
to confirm.
19; 02; 05
Return date
We
Note:
After approximately 4 sec. “Departure
date” will be displayed. Press j again
if you want to terminate setting a
holiday program early.
23; 02; 05
7. The room temperature during the
holiday program is the selected
reduced room temperature (see page
19).
If you want to change this
temperature:
H Press “tm”.
Ending holiday program:
H The holiday program terminates
automatically on the day of return.
H Press j again if you want to
terminate the holiday program early
and confirm “Delete? Yes” with
.
5369 299 v1.1
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
- Select the heating circuit with ⊕ /
, to which the central heating
should apply.
- Confirm twice with
.
- Press “tm” again.
H Select the required value with ⊕/.
to confirm; the temperature
H Press
no longer flashes and is now saved.
Note:
This change generally applies to the
reduced room temperature and must be
modified again, if required, after the
holiday program ends.
22
Adjusting the Room Temperature
Changing the Room Temperature for a Few Hours Only
The following functions enable you to
change your room temperature for
several hours, without permanently
altering your control settings.
H You want to leave your home and,
according to the time program, central
heating with normal room
temperature is currently selected. To
save energy, you can reduce the
normal room temperature with
“Energy saving mode” û .
H You want to heat spontaneously with
the normal room temperature and
provide DHW (e.g. when guests
unexpectedly stay longer in the
evening). For this, select “Party
mode” “g” (see page 24).
Selecting energy saving mode
In energy saving mode, the normal room temperature will be reduced automatically.
Energy saving mode ends automatically with the next change to central heating
with “Red. room temp.”.
Economy mode
1. û
for “Energy saving mode”.
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
- Select the heating circuit with
⊕ / , to which the adjustment
should apply.
- Confirm twice with
.
- “û” again for “Energy saving
mode”.
2. Ending energy saving mode
If you want to terminate energy
saving mode early, press “û”.
5369 299 v1.1
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
- Select the heating circuit with ⊕ /
, to which the adjustment should
apply.
- Confirm twice with
.
- Press “û” again.
23
Adjusting the Room Temperature
Changing the Room Temperature for a Few Hours Only
(continued)
Selecting party mode
H Central heating will be enabled at any
temperature you select (party
temperature).
H The DHW will be boosted to the set
temperature.
H The DHW circulation pump is
switched ON (if installed).
Press the following keys:
1. g
Party mode
68ºF
for “Party mode”; the value of
the party temperature flashes.
If “Select htg. circuit”; is
displayed and “1r
r“ flashes:
H Select the heating circuit
with ⊕ / , to which the
adjustment should apply.
H Confirm twice with
.
H “g” again for “Party mode”;
the party temperature flashes.
2. ⊕/ for the required temperature, if
you want to change the room
temperature.
3.
to confirm; the temperature no
longer flashes and is saved.
4.
to exit the setting menu.
5. Ending party mode
H Party mode ends automatically with
the next changeover to central heating
with normal room temperature, but
no later than after 8 hours.
H If you want to terminate party mode
early, press “g” again.
5369 299 v1.1
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
- Select the heating circuit with ⊕ /
, to which the adjustment should
apply.
- Confirm twice with
.
- Press “g” again.
24
Selecting DHW Heating
Selecting Constant DHW Heating
Observe the following points if you
want to enable DHW heating:
1. Set “Htg. + DHW” “r
rw“ or “DHW
only” “w
w“ for the selected heating
circuit.
Check:
“r
rw“ or “w
w“ must be illuminated,
otherwise press “r
rw“ or “w
w“.
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
H Select the heating circuit with ⊕ /
, to which the adjustment should
apply.
H Confirm twice with
.
H “r
rw“ or “w
w“ must be illuminated,
otherwise press “r
rw“ or “w
w“.
2. The timing of when DHW heating is
enabled and when the DHW
circulation pump runs, depends on
the settings of the time program).
You can scan the time programs (see
page 33).
Note:
You can adjust the DHW
temperature. See “DHW temperature
setting” section.
Note:
For changing the time program, (see
page 26).
DHW temperature setting
Press the following keys:
1. tw
Set DHW temperature
2. ⊕/ for the required temperature.
ºF
3.
to confirm; the temperature no
longer flashes and is saved.
5369 299 v1.1
122
w
for “DHW temp. setpt.”; the
current temperature will flash.
25
Selecting DHW Heating
Selecting Constant DHW Heating
(continued)
Selecting a time program (switching times)
Heating system without DHW
recirculation pump
DHW can be enabled / disabled up to
four times per day (four time phases).
Automatic mode is set in the time
program in the factory. That means
DHW heating is enabled in parallel to
the central heating program of the first
available heating circuit, but starts
30 min. earlier (from 05:30 to
22:00 hrs.).
Should you not wish to operate in
automatic mode, you can also set up
individual time programs. You can select
identical time programs for every day or
individual programs for each day.
When setting time programs, bear in
mind that your heating system requires
some time to heat the DHW tank to the
required temperature.
For time programming steps, (see pages
26 and 27). For a sequence of steps to
delete a time phase, (see page 28).
Heating system with DHW recirculation
pump
The DHW recirculation pump transports
hot water through a circuit between the
DHW tank and the draw-off points to
deliver DHW to the taps as quickly as
possible.
DHW heating and the DHW recirculation
pump can be enabled / disabled up to
four times per day (four time phases).
Automatic mode is set in the time
program at the factory. That means
DHW heating and the DHW recirculation
pump are activated in parallel to the
central heating program of the first
available heating circuit, but starts 30
min. earlier (from 05:30 to 22:00 hrs.).
Should you not wish to operate in
automatic mode, you can also set up
individual time programs. You can select
identical time programs for every day or
individual programs for each day.
When setting time programs, bear in
mind that your heating system requires
some time to heat the DHW tank to the
required temperature.
Also, enabling the DHW recirculation
pump is only sensible for those times
when DHW is actually drawn.
For time programming steps, (see pages
26 and 27). For a sequence of steps to
delete a time phase, (see page 28).
Selecting automatic mode (if required)
Press the following keys:
1. uw for “DHW time program”.
2. ⊕/ to select “DHW time
program”, or “Recirc. pump
time program”.
3.
to confirm.
4. ⊕/ for “Automatic?”, if
“Automatic?” is not yet
displayed.
to confirm.
5369 299 v1.1
5.
26
Selecting DHW Heating
Selecting Constant DHW Heating
(continued)
Setting up an individual time program
The following explains the setting up of a time program using DHW heating “uw”
as an example. For the DHW recirculation pump time program, proceed as described
above, after you have selected “Recirc. pump time program”.
Press the following keys:
1. uw for “DHW time program.”.
Note:
If you want to terminate the time
programming early, press “uw”
again and confirm with
.
2. ⊕/ to select “DHW time
program.”, or “Recirc. pump
time program.”.
to confirm.
3.
4. ⊕/ for “Individual?”, if Individual?”
is not yet displayed.
to confirm.
5.
DHW time prog.
1-7
6. ⊕/ until “1-7” is displayed, if you
want to set up the same time
phases for every day.
Or..
DHW time prog.
Mo
7. ⊕/ until “Mo”, “Tu” etc. is
displayed, if you want to set
different time phases for the
displayed day.
8.
to confirm; “DHW timer 1” will
then be displayed.
9.
to confirm; “DHW timer 1 ON”
will then be displayed.
Note:
If different time phases are set for
individual days and you want to
return to identical time phases for
every day, press
when “1-7” is
displayed.
All time phases are returned to their
original delivered condition.
Note:
Press ⊕ if you want to skip a time
phase.
10. ⊕/for DHW phase starting point.
11.
to confirm; “DHW cycle 1 Off”
will be displayed.
12. ⊕/for DHW phase end point.
5369 299 v1.1
13.
to confirm; “DHW cycle 2 On”
will then be displayed.
14. Proceed for setting the start and
end of DHW phases 2 to 4 as
described in steps 9 to 11.
27
Selecting DHW Heating
Selecting Constant DHW Heating
(continued)
Setting up an individual time program (continued)
Press the following keys if you want to
delete a time phase:
1. uw for “DHW time program”.
2.
until the required “DHW phase
Off” is displayed.
3. until “- - : - -” is displayed for
the end time.
4.
to confirm; until the boiler
water temperature is displayed.
DHW phase 2 OFF
--:--
5369 299 v1.1
1-7
28
Selecting DHW Heating
Selecting DHW Heating for a Few Hours Only
The following functions enable you to heat DHW for several hours, without
permanently altering your control settings. For this, select “Party mode” “g”.
During party mode, the DHW recirculation pump is active and central heating
operates with the party temperature. Set the party temperature to 39.2ºF / 4ºC, if
you require no central heating (e.g. in summer).
Press the following keys:
1. g
Party mode
68
for “Party mode”; the value of
the party temperature flashes.
If “Select htg. circuit”; is
displayed and “1r
r“ flashes:
H Select that heating circuit
with ⊕ / , to which the
adjustment should apply.
H Confirm twice with
.
H “g” again for “Party mode”;
the party temperature flashes.
ºF
2. ⊕/ for the required temperature, if
you want to change the room
temperature.
3.
to confirm; the temperature no
longer flashes and is saved.
4.
to exit the setting menu.
5. Ending party mode
H Party mode ends automatically with
the next changeover to central
heating with normal room
temperature, but no later than after
8 hours.
H If you want to terminate party
mode early, press “g” again.
5369 299 v1.1
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
H Select that heating circuit with
⊕ / , to which the adjustment
should apply.
H Confirm twice with
.
H Press “g” again
29
Selecting DHW Heating
Selecting DHW Heating for a Few Hours Only
(continued)
Selecting DHW heating only once
The following function enables you to heat DHW once, without permanently altering
your settings. For this, select “Party mode” “g”.
The following function enables you to
heat DHW once, without permanently
altering your settings. For this, select
“Party mode” “g”.
Precondition:
H Not in “Standby mode” “9” and not
in the “Holiday program” “j”.
H The DHW temperature must be below
the set value.
Press the following keys:
1. g
Party mode
68ºF
for “Party mode”; the value of
the party temperature flashes.
If “Select htg. circuit”; is
displayed and “1r
r“ flashes:
H Select that heating circuit
with ⊕ / , to which the
adjustment should apply.
H Confirm twice with
.
H “g” again for “Party mode”;
the party temperature flashes.
2.
to confirm; DHW heating
begins.
5369 299 v1.1
3. After approximately 10 sec., press
“g” again.
30
Further Adjustments
Time and Date
Date and time are factory-set and may be changed manually. During commissioning,
or after prolonged time out of use, it may be necessary to set the time and date.
Note:
Summer/winter time will be
automatically changed over.
Press the following keys:
Note:
Summer/winter time will be
automatically changed over.
1. uý for “Time”.
2. ⊕/ for the required time.
Time
09:05 u
3.
Date
Sa
to confirm;”Date” will then be
displayed.
4. ⊕/ for the required date.
19;02;05
5.
to confirm.
Language
Press the following keys:
Outdoor temp.
i
1.i
“Outdoor temp.”will be
displayed.
2. for the required language.
3.
to confirm.
68ºF
English
i
Adjusting the display contrast
Open the programming unit flap. Press
and simultaneously adjust the
contrast with ⊕ or .
5369 299 v1.1
Standard setting
All modified values are reset to their
factory settings by pressing “D”.
31
Scanning Options
Scanning Information
Subject to the connected components and settings you have made, you can scan
the actual temperatures and operating conditions.
Press the following keys:
1.i
Outdoor temp.
i
68ºF
for example, “Outdoor temp.”
may be displayed.
If “Select htg. circuit”; is
displayed and “1r
r“ flashes:
H Select that heating circuit
with ⊕ / , to which the
adjustment should apply.
H Confirm twice with
.
H Press i again.
2. ⊕/ for further scanning of the list.
3.i
to end scanning.
Order in which temperatures and operating conditions may be scanned
You can scan various current temperatures and operating status information
depending on the system components and the settings.
32
H Heating pump ON / OFF - for external
heating circuit pump for heating circuit
A1 (pump 20A)
H Tank pump ON / OFF (pump 21)
H C pump ON / OFF - DHW recirculation
pump (pump 28)
H Central fault m. ON / OFF - central
fault message (output 50)
H Mixing valve
Mixing valve open - fully open
Mixing valve - intermediate position
Mixing valve closed - fully closed
H Solar circuit pump ON / OFF (not
used)
H Solar circuit pump ...hrs. - solar circuit
pump hours run (not used)
H Language
*1 To reset to “0”: Press D and confirm
.
with
5369 299 v1.1
H Subscriber no. - in connection with
other control units
H Holiday program - (if entered) with
dates of departure and return
H Outdoor temperature
H Boiler water temperature
H Flow temperature - for heating circuit
with mixing valve
H Normal room temp. - set value
H Room temperature - actual value only
if a remote control unit is connected
H Ext. Set room temp. - only if external
hook-up has taken place
H DHW temperature - DHW temperature
H Solar DHW temp. - DHW temperature
in solar mode (if used)
H Collector temperature - only if a solar
heating system is connected
H Common flow temp. - common flow
temperature for systems with low loss
header
H Burner*1 - burner hours run
H Burner starts*1
H Solar energy - display in kWh (only if a
solar heating system is connected)
H Time
H Date
H Burner ON / OFF
H Int. pump ON / OFF (boiler pump)
H Int. output ON / OFF - for internal
connection extension
Scanning Options
Scanning Time Programs
Central heating time program
Press the following keys:
1-7
1. ur+i press and hold down
simultaneously for central
heating time program; the
set time phases will then be
displayed on a time slot
graphic.
If “Select htg. circuit” is displayed
and “1r
r“ flashes:,
H Select that heating circuit with
⊕ / , to which the adjustment
should apply.
H Confirm twice with
.
H Again, press and hold down
“ur+i simultaneously; a time
slot graphic shows the selected
time phases.
For changing the time program, (see
page 26).
DHW time program
Note:
For changing the time program, (see
page 26).
5369 299 v1.1
1-7
1. uw+i press and hold down
simultaneously for DHW
time program; the set time
phases will then be
displayed on a time slot
graphic.
33
Scanning Options
Scanning Time Programs
(continued)
Scanning fault display
If your heating system has developed a fault, it will be displayed and indicated by
the flashing red fault indicator.
You can read off the fault code on the display by scanning; then notify your local
heating contractor accordingly. This allows your heating contractor to better
prepare for the service call and may save additional travelling costs.
Fault display examples:
Control unit fault
Fault
ºF
Tu
Fault on a burner component
Fault
E
Press the following keys:
1. E
in case of a fault on a burner
component.
2.i
for troubleshooting.
Example:
In this case, notify your local
heating contractor of fault (1)
message “38”.
3.
to “Acknowledge”.
Boiler sensor
U
1
38
Acknowledge? Yes
4. ⊕/ for “Yes” or “No”.
With “Acknowledge? Yes” you
confirm that you have noted
the fault.
to confirm.
Note:
If the fault has not been rectified, the
fault message will be displayed again at
07:00 hrs. the following day.
The red fault indicator flashes until the
fault has been rectified.
5369 299 v1.1
5.
34
Other Settings
Changing the Heating Pattern of the Boiler
Rooms are too cold
Cause
Remedy
The heating system is switched OFF.
ON indicator “8” (green) OFF.
Switch system ON / OFF switch “8” ON (see page 13).
Switch ON the main breaker, if installed (outside the boiler room).
Reset circuit breaker inside the power distribution panel.
Control unit or remote control incorrectly
adjusted.
Check settings and correct, if required:
- Room temperature
- Time
- Time program
Only when operating with DHW heating:
DHW priority (wp is displayed).
Wait until the DHW tank has been heated up (p disappears from the
display).
In connection with the Vitotronic 200-H or
extension kit for heating circuits with mixing
valve: The ON / OFF switch on the mixing valve
motor is switched OFF.
Switch ON / OFF switch on the mixing valve motor ON, I=ON.
No fuel.
With Natural Gas / LPG:
Open the gas shut-off valve and check with your gas supplier, if
required. Press burner fault reset “E
E”.
”Fault” and “E
E” are displayed; the red fault
indicator at the control unit flashes.
Press burner fault reset “E
E” - if that fails, notify your heating
contractor.
Control unit fault: ”Fault” is displayed and the red
fault indicator flashes.
Scan the type of fault and notify your local heating
contractor.
Mixing valve motor faulty.
Unhook motor lever A and manually set mixing valve lever B. Notify
your local heating contractor.
A
B
Rooms are too hot
Remedy
Control unit or remote control incorrectly
adjusted.
Check settings and correct, if required:
- Room temperature
- Time
- Time program
Control unit or outside temperature sensor faulty:
”Fault” is displayed and the red fault indicator
flashes.
Scan the type of fault and notify your local heating
contractor.
5369 299 v1.1
Cause
35
Other Settings
Changing the Heating Pattern of the Boiler
(continued)
There is no hot water
Cause
Remedy
The heating system is switched OFF.
ON indicator “8” (green) OFF.
Switch system ON / OFF switch “8” ON.
Switch ON the main breaker, if installed (outside the boiler room).
Reset circuit breaker inside the power distribution panel.
Control unit or remote control incorrectly
adjusted.
Check settings and correct, if required:
- DHW heating must be switched ON
- DHW temperature
- Time program
- Time
No fuel.
With Natural Gas / LPG:
Open the gas shut-off valve and check with your gas supplier, if
required. Press burner fault reset “E
E”.
Control unit fault: ”Fault” is displayed and the red
fault indicator flashes.
Scan the type of fault and notify your local heating
contractor.
The DHW is too hot
Cause
Remedy
Control unit incorrectly adjusted.
Check and, if required, correct DHW temperature (see page 25).
”Select htg. circuit” flashes in the display
Cause
Remedy
Control element activated without selecting a
heating circuit first.
Select that heating circuit, to which the adjustment should apply
”Fault” flashes in the display
Cause
Remedy
Heating system fault.
Scan for the type of fault and notify your local heating
contractor.
The time flashes in the display
Cause
Remedy
Longer heating system off periods.
Reset the time and date.
Cause
Remedy
The heating system requires a service.
Ask your local heating contractor to service the boiler.
36
5369 299 v1.1
”Service” is displayed
Other Settings
Changing the Heating Pattern of the Boiler
(continued)
“Remote control” is displayed
Cause
Remedy
A remote control is connected to the heating
circuit.
Make adjustments or carry out scans at the remote control (see
separate operating instructions).
”Ext. control” is displayed
Cause
Remedy
The heating program set at the control unit was
changed over by an external device
(e.g. connection extension).
No action required. The heating program changeover was manually
selected.
”Ext. program” is displayed
Cause
Remedy
The heating program set at the control unit was
changed over by the Vitocom 100 communicating
interface (not used).
No action required. The heating program changeover was manually
selected.
”Ext. room t. setpt.” is displayed
Cause
Remedy
A room set point temperature has been connected No action required. The connection was manually selected.
via the communication interface.
”Without function” is displayed
Remedy
No function is allocated to the key you have
pressed.
No action required. Select appropriate key.
5369 299 v1.1
Cause
37
Service Instructions
Service Instructions for Your Heating System
Viessmann strongly recommends inspection/service of the boiler and the system by
a licensed professional heating contractor once a year.
Before the heating season begins, the boiler with its burner(s) and direct vent
system should be serviced by a qualified heating contractor. Service contracts may
be established through gas suppliers or other licensed contractors in your area.
Regular inspection/service ensures trouble-free, energy-efficient and
environmentally friendly heating activity of your heating system.
Domestic hot water storage tank
Inspection and (if necessary) cleaning of
the tank must take place within 2 years
of initial start-up and as required
thereafter.
Cleaning of the inside surfaces of the
DHW storage tank, including DHW
connections, may only be performed by
a licensed professional heating
contractor.
Vitocell 100:
Viessmann recommends an annual
inspection, and replacement if required,
of the consumable anode by a licensed
professional heating contractor.
The inspection can be carried out during
regular operation of the heating system;
shut-down is not required.
The heating contractor measures the
protective current with an anode tester.
Drinking water filter (if installed)
For hygienic reasons
H replace filter element every
6 months on filters which cannot be
flushed back, and perform a visual
inspection every 2 months,
H flush back reversible flow filters
every 2 months.
Safety valve (DHW tank)
The safety valve function should be
checked every six months by venting,
either by the system user or the local
heating contractor. The valve seat may
become contaminated.
38
Notes on operation:
H Ensure boiler room and boiler
are clean.
H Regularly check heating system
pressure on the pressure gage:
If the needle of pressure gage is
below 12 psig, the system pressure
is too low; in this case, please
contact your heating contractor.
IMPORTANT
If the domestic cold water supply to the
hot water storage tank has a water
treatment device (water softener)
installed, ensure its proper working
condition is checked regularly by your
heating contractor.
The same applies if a dirt trap or a
water filter is installed in the domestic
cold water supply. Any of these devices
installed in the domestic cold water
supply must be flushed out and serviced
on a regular basis.
Please follow manufacturer’s
instructions.
Please follow manufacturer’s
instructions.
5369 299 v1.1
Boiler
All boilers must be cleaned on a regular
basis as debris build-up will result in
increased flue gas temperature, and
thus in increased energy consumption.
How to Save Energy
How to Save Energy
.... by heating correctly
Apart from taking advantage of the benefits of a modern heating system, there is a
lot you can do yourself to achieve additional fuel savings. For instance:
1
3
2
H Don’t overheat:
Aim at a room temperature of
68ºF / 20ºC. Every degree less in
room temperature will reduce your
heating bills by up to 6%.
H Close window shutters 1 (if installed)
at dusk.
H Operate thermostatic valves 2
correctly.
H Don’t obstruct radiators 3 and
thermostatic valves 2.
6
5
H Make use of individual adjustment
options of the control unit 4;
(e.g. ”normal room temperature”
alternating with ”reduced room
temperature”).
H Set the domestic hot water
temperature of the DHW tank 5 on
the control unit 4.
H Control your consumption of hot
water:
A shower generally consumes less
energy than a bath.
4
... with regular maintenance
Regular maintenance check-ups of your heating system 6 by a licensed professional
heating contractor will ensure energy savings and environmentally friendly operation.
.... with effective insulation
If you wish to make use of additional energy-saving measures, check the thermal
insulation:
5369 299 v1.1
H of heating and domestic hot water
pipes.
H of external walls and the roof.
H between heated and unheated rooms.
H of the windows.
39
Additional Information
Lighting and Operating Instructions
FOR YOUR SAFETY READ BEFORE OPERATING
W A R N I N G: If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
A. This appliance does not have a pilot. It is equipped
with an ignition device which automatically lights
the burner. Do not try to light the burner by hand.
B. BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not
push in or turn by hand, don’t try to repair it, call a
qualified service technician. Force or attempted
repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service
technician to inspect the appliance and to replace
any part of the control system and any gas control
which has been under water.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this
label.
2. Set thermostat or other operating control to lowest
setting.
3. Turn off all electric power to the appliance.
4. This appliance is equipped with an ignition device
which automatically lights the burner. Do not try to
light the burner by hand.
Manual gas shutoff
5. Close main gas shut-off valve.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow ”B” in the safety information
above on this label. If you don’t smell gas, go to the
next step.
7. Open main gas shut-off valve.
8.
Turn on all electric power to the appliance.
9.
Set thermostat or other operating control to
desired setting.
10. If the appliance will not operate, follow the
instructions ”To Turn Off Gas To Appliance” and
call your service technician or gas supplier.
Closed
Open
TO TURN OFF GAS TO APPLIANCE
2. Turn off all electric power to the appliance if service
is to be performed.
3. Close main gas shut-off valve.
40
5369 299 v1.1
1. Set thermostat or other operating control to lowest
setting.
5369 299 v1.1
41
42
5369 299 v1.1
5369 299 v1.1
43
Viessmann Manufacturing Company (U.S.) Inc.
45 Access Road
Warwick, Rhode Island 02886 USA
1-800-288-0667 Fax (401) 732-0590
www.viessmann-us.com info@viessmann-us.com
44
-40
-31
-13
-4
0
+3
+7
+10
+14
+16
+18
+19
+21
+23
+25
+27
+28
+30
+32
+34
+36
+37
+39
+41
+43
+45
+46
+48
+50
+54
+57
+61
+64
+68
+77
+86
+95
+104
+122
+140
+158
+176
+194
+212
+230
Viessmann Manufacturing Company Inc.
750 McMurray Road
Waterloo, Ontario N2V 2G5 Canada
1-800-387-7373 Fax (519) 885-0887
www.viessmann.ca info@viessmann.ca
Printed on environmentally friendly
(recycled and recyclable) paper.
-40
-35
-25
-20
-18
-16
-14
-12
-10
-9
-8
-7
-6
-5
-4
-3
-2
-1
0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+10
+12
+14
+16
+18
+20
+25
+30
+35
+40
+50
+60
+70
+80
+90
+100
+110
°F
Technical information subject to change without notice.
°C
5369 299 v1.1
Quick Reference
Download PDF