Domestic Use
Dishwasher
Instruction Manual
25
26-28
29
Care, Maintenance
and Troubleshooting
Logik LDW6TTW_IB_GB_090605.indd 1
23
23-24
25
25
Operating Instructions
DSG Retail Limited is responsible
for after sales service.
If you have a query about the
product please contact our product
support line
08701 565 550 (Currys).
External Care
Internal Care
Frost Precaution
Moving the Dishwasher
Maintenance
After Prolonged Periods
of Non-Operation
Troubleshooting Guide
Specifications
Before Use
Model LDW6TTW
Table of Contents
Know your Logik Dishwasher
2
Safety Information
3-6
Disposal of Dishwasher
6
Disposal of Packing Material
7
Product Overview
8-9
Control Panel Overview
9-10
Before Operating
12-16
To open the Door
12
To close the Door
12
Items not suitable for use in the Dishwasher
12-13
Adding the Detergent or Detergent
Tablet
13
Adding of Rinse Aid
14
Adding of Salt
15
Loading the Dishwasher
17-19
Before loading the Dishwasher 17
Dishwahser Basket
18
Cutlery Basket
19
Loading the Cutlery Basket
20
Starting a Wash Cycle
21-22
Changing a Programme
21
At the End of Programme
22
Switching off the Unit
22
Unloading the Dishwasher
22
Cleaning
after use
23-
05/06/09 3:32:20 PM
Know your Logik Dishwasher
Before using your Logik appliance
• Read these instructions carefully and retain for future
reference.
• Remove all packaging labels. Please dispose of them
properly.
Before calling for service
• Refer to Troubleshooting Tips section. This will help
you to solve some general problems by yourself.
Note
• This product has been wet tested to ensure correct
operation. As a result some water may remain inside
the unit. This is normal and safe. Remove any water
droplets from the exterior if necessary.
GB-
Logik LDW6TTW_IB_GB_090605.indd 2
05/06/09 3:32:21 PM
Safety Information
Before Use
General Safety
• Switch off and unplug before fitting or removing
tools/attachments, after use and before cleaning.
• Keep your fingers away from moving parts and fitted
attachments.
• Never use a damaged machine.
• Keep cord out of reach from children.
• Keep the power unit, cord or plug away from water.
• Never exceed the maximum capacities.
• When using an attachment, read the accompanying
safety instructions.
• Take care when lifting this appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• Only use the appliance for its intended domestic use.
The company responsible for this product, DSG Retail
Limited, will not accept any liability if the appliance
is subject to improper use, or failure to comply with
these instructions.
GB-
Logik LDW6TTW_IB_GB_090605.indd 3
05/06/09 3:32:21 PM
Safety Information
Earthing Instructions
• WARNING: THIS APPLIANCE MUST BE EARTHED.
• This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing plug.
• The plug must be plugged into an appropriate outlet
that is installed and earthed in accordance with local
standards and requirements.
Warning!
• Improper connection of the equipment-earthing conductor could result in a risk of electric shock.
• The wires in the cord are coloured as follows:
Green and Yellow = Earth,
Blue = Neutral,
Brown = Live.
• Check with a qualified electrician or service representative if you are in doubt whether the appliance is
properly earthed or the plug does not fit correctly.
• Never modify the plug provided with the appliance.
Proper Use
• Do not sit or stand on the door or dish rack.
• Do not move your dishwasher by holding the door or
its edges. Hold the dishwasher around its sides or base
when moving it.
• Do not touch the heating element during or immediately after use.
• Do not operate your dishwasher unless all enclosure
panels are properly in place. Open the door very carefully when there is a programme running as there is a
risk of hot water spraying out of the appliance.
• Do not place any heavy objects on the open door. The
appliance could tip.
• When loading items to be washed:
1) Locate sharp items so that they will not damage the
door seal;
GB-
Logik LDW6TTW_IB_GB_090605.indd 4
05/06/09 3:32:21 PM
Safety Information
•
•
•
•
•
•
•
•
•
•
•
Before Use
•
2) Warning: Knives and other utensils with sharp
points must be loaded in the basket with the points
downwards or placed horizontally.
Do not allow plastic items to come into contact with
heating element.
Check that the detergent receptacle is empty aftercompletion of the wash cycle.
Do not wash plastic items unless they are markeddishwasher safe or equivalent.
Use only detergent and rinse aids designed for an
automatic dishwasher.
Other means for disconnection from the supply must
be incorporated in the fixed wiring with at least 3mm
contact separation in all poles.
Keep children away from detergents and rinse aids.
These may cause chemical burns in the mouth, throat
and eyes or asphyxiation.
Keep children away from the dishwasher when the
door is open.
The door should not be left in the open position since
this could present a tripping hazard.
For energy saving, always remember to switch thedishwasher off when you have finished using it. The
dishwasher should not be left unattended when in
use.
If the supply cord is damaged, it must be replaced by
the manufacturer or its service agent in order to avoid
a hazard.
Remove the door to the washing compartment whenremoving an old dishwasher from service or discarding it.
GB-
Logik LDW6TTW_IB_GB_090605.indd 5
05/06/09 3:32:21 PM
Safety Information
•
•
•
•
•
During installation, the power supply cord must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
The appliance is to be connected to the water mains
using new hose sets.
The maximum number of place settings to be washed
is 6.
The maximum permissible inlet water pressure is
1Mpa, and the minumum permissible inlet water pressure is 0.04Mpa.
Disposal of the Dishwasher
•
•
•
When disposing your old dishwasher, first make it
unusable. Disconnect, cut off the cable and the plug
from the cable. Make the door lock inoperative, so
that children cannot accidentally shut themselves in.
Make appropriate arrangements for the disposal of
the dishwasher.
At the end of its working life, the product must not
be disposed of as urban waste. It must be taken to a
special local authority differentiated waste collection
centre or to a dealer providing this service. Disposing
of a household appliance separately avoids possible
negative consequences for the environment and
health deriving from an inappropriate disposal and
enables the constituent materials to be recovered to
obtain significant savings in energy and resources.
As a reminder of the need to dispose of household
appliances separately, the product is marked with a
crossed-out wheeled dustbin.
Please ensure that it presents no danger to children
while being stored for disposal.
GB-
Logik LDW6TTW_IB_GB_090605.indd 6
05/06/09 3:32:21 PM
disposal of packing material
•
Please dispose of the plastic wrappings and bags
safely and keep out of the reach of babies and young
children.
Before Use
GB-
Logik LDW6TTW_IB_GB_090605.indd 7
05/06/09 3:32:21 PM
Product Overview
Front View
Rear View
4
3
2
1
5
7
6
Dishwasher Basket
Cutlery Basket
part number 673006200014
1. Door Handle
2. Dishwasher Model Number
3. Control Panel
4. Power Button and Indicator Light
5. Drain Outlet (Connect to drain hose)
6. Mains Cable (Connect to electrical mains outlet)
7. Water Inlet (Connect to water supply hose)
GB-
Logik LDW6TTW_IB_GB_090605.indd 8
05/06/09 3:32:24 PM
Internal View
15
9
Before Use
OPEN
11
10
9. Air Inlet
12
10. Salt Reservoir
11. Detergent Dispenser (Dual Compartment)
12. Rinse Aid Dispenser
13. Filtering System
14. Spray Arm (Under the Dishwasher Basket)
15. Cutlery Basket
14
13
Accessories
water supply
hose X 1
part number
673005400041
Drain Hose
Mounting
Clamp X 1
part number 673005400045
measuring
cup X 1
60ml
(approx)
part number 673006200004
part number
672005400002
salt funnel X 1
20ml
Drain Hose X 1
detergent measuring spoon
x1
1 full spoon = 20g (approx.)
part number 673002200079
Instruction Manual X 1
part number 675005900815
U-shape
hose holder
X1
part number
673002200001
part number 673006200003
Installation Guide X 1
part number 675005900823
GB-
Logik LDW6TTW_IB_GB_090605.indd 9
05/06/09 3:32:36 PM
Control Panel Overview
LDW6TTW
1
2
1
4
On/Off button
- To turn the dishwasher on and off.
2
Power Indicator
- The LED light will illuminate when
the dishwasher is on.
3
Salt Refill Warning light
- illuminates when the salt reservoir needs
refilling.
Rinse Aid Refill Warning light
- illuminates when the rinse aid dispenser
needs refilling.
Programme Indicators
- The LED light will illuminate
when the washing programme is
selected.
- It will flash when the selected
washing programme is running.
5
Programme button
- To select your required washing
programme.
- Each press of this button switches from one washing programme
to another.
6
Start/Pause button
- To confirm and start the selected washing programme.
- To reset the washing programme.
GB-10
Logik LDW6TTW_IB_GB_090605.indd 10
05/06/09 3:32:38 PM
4
5
3
Before Use
Program
Start/Pause
6
Wash Cycle Table
Programme
Cycle
Selection Information
•
Intensive
Pre-wash
(50°C)
Wash (70°C)
Rinse (x2)
Rinse (70°C)
Drying
•
•
•
•
•
•
•
•
•
•
Pre-wash
Wash (60°C)
Rinse
Rinse (70°C)
Drying
•
Pots, utensils and
cutlery.
Normally soiled.
•
•
•
•
•
Pre-wash
Wash (55°C)
Rinse
Rinse (70°C)
Drying
•
A shorter wash for
lightly soiled items.
•
•
•
•
•
Pre-wash
Wash (45°C)
Rinse
Rinse (60 °C)
Drying
•
Glasses, crystal and
fine china.
Lightly soiled.
•
•
•
•
Wash (40°C)
Rinse
Rinse (45°C)
Drying
•
•
•
•
•
•
Pre-wash
Wash (60 °C)
Rinse
Rinse (70 °C)
Drying
•
Pots, utensils and
cutlery.
Highly soiled.
Normal
*Economy
Glass
Glasses and cups.
Lightly soiled.
Rapid
3-in-1
Detergent
Amount
(Pre-wash /
Main wash)
Process
Utensils and
cutlery.
Normally soiled.
•
•
•
Prre-wash
(3g)
Main Wash
(15g)
Prre-wash
(3g)
Main Wash
(15g)
Prre-wash
(3g)
Main Wash
(15g)
Running
Time
(min.)
Energy
Consumption
(Kwh)
Water
Consumption
(l)
145
0.94
11
125
0.70
8.4
170
0.63
8.4
75
0.48
6.8
30
0.3
6
140
0.7
8.4
Rinse
Aid
Main Wash
(15g)
Main Wash
(15g)
Use 3 in 1
detergent
tablet only.
*To comply with Standards of Performance, i.e. EN50242, please ensure all the cutlery must be loaded according to the instruction in this manual.
GB-11
Logik LDW6TTW_IB_GB_090605.indd 11
05/06/09 3:32:39 PM
Before Operating
To open the Door
•
•
Pull the door handle.
If the door is opened during operation all functions are automatically
interrupted.
To close the Door
•
•
•
After loading the dishes, push the baskets fully into the dishwasher.
Lift the door upwards and push until it clicks into position.
Do not slam the dishwasher door.
Items not suitable for use in the Dishwasher
THEÖFOLLOWINGÖITEMSÖAREÖNOTÖSUITABLEÖFORÖDISHWASHER
?
? CRYSTALÖGLASSES
VALUABLEÖVASES
TOWELÖANDÖSPONGE
CRACKEDÖÖCHIPPEDÖCHINA
SILVERWARE
?
SMALLÖPLASTICÖITEMSÖ
MILKÖBOTTLEÖNIPPLE
?
CASTÖIRONÖPANS
COPPERÖPOTSÖANDÖPANS
PLASTICÖITEMSÖTHATÖ
AREÖNOTÖDISHWASHERÖSAFEÖ
SCRATCHEDÖNONSTICKÖCOOKWARE
When purchasing new crockery and cutlery, please make sure they are dishwasher-proof. Some items are not suitable for dishwashers.
• Wooden cutlery and crockery or items with wooden parts may discolour
and fade. The glue used in these items is not dishwasher-proof either,
and the wooden handles may come loose after being washed in a dishwasher.
• Craft items, antiques, valuable vases and decorative glassware are also
not suitable for dishwashers.
• Plastic items (e.g. tupperware) which are not heat resistant may melt or
lose shape due to the high temperatures in the dishwasher.
• Copper, brass, tin and aluminium items may discolour or become matt.
GB-12
Logik LDW6TTW_IB_GB_090605.indd 12
05/06/09 3:32:39 PM
•
•
Clouding may occur on glasses and delicate glassware after frequent
washing. Do not wash delicate glassware, or glassware containing lead
crystal in a dishwasher. Please wash delicate glassware by hand instead.
Silver and aluminium parts have a tendency to discolour during washing. Residues like egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore, please clean the residues from
silver immediately after use.
Adding the Detergent or Detergent Tablet
Only use detergents specifically designed
for use in dishwashers.
To be more environmentally friendly,
please use no more than the correct
amount of detergent.
WARNING!
Keep out of the reach of children
- Irritating to eyes.
- Avoid contact with eyes. In
case of contact with eyes, rinse
immediately with plenty of water
and seek medical advice.
- If swallowed, seek medical
advice immediately.
push up from the right side
1
main wash detergent chamber
Operating Instructions
Please follow the steps below to fill the
detergent dispenser.
1. Push the button on the lid of the detergent dispenser in the direction of
the arrow until the flap springs open.
(Fig 1)
2. Fill the detergent dispenser with detergent powder or insert the detergent tablet. The marking indicates the
dosing level. (Fig 2)
TIP: You can choose to add a detergent
tablet alone or to add detergent powder
to both main wash detergent chamber
and the pre-washer detergent chamber
for your selected wash cycle.
1. All programmes with pre-wash need
an additional detergent dosage
(please refer to the wash cycle table)
that must be placed in the pre-wash
detergent chamber. This detergent
will take effect during the pre-wash
phase. (Fig 2)
2. Close the lid firmly so that it clicks
into place.
Irritant
Bleach and
Countertop detergent
2
or
pre-wash detergent chamber
GB-13
Logik LDW6TTW_IB_GB_090605.indd 13
05/06/09 3:32:41 PM
Adding of Rinse Aid
Rinse aid helps to ensure water does
not cling and leave marks on crockery
during the drying phase and helps
crockery dry faster after it has been
washed. Only pour rinse aid that is for
domestic dishwashers into the reservoir.
This model is designed to use liquid
rinse aids only.
Please follow the steps below to pour
the rinse aid into the storage reservoir,
and the amount will dispense automatically.
1. Turn the cap and open as indicated
in Fig 1.
2. When the cap open marking is
aligned (Fig 2a), you may lift the cap
up (Fig 2b).
3. Pour the rinse aid until the level
indicator turns completely black in
colour and close the cap. (Fig 3)
4. Be careful not to overfill the reservoir. Wipe up any spills. The approximate volume of the rinse aid reservoir is 110ml.
1
rinse aid indicator
open
2a
2b
3
NOTE: If the water hardness in your area is soft, you may not need rinse aid
as it may cause white film to develop on your dishes.
Rinse aid indicator light on the display window will
illuminate when the reservoir is running out of rinse aid
and required re-filling.
Rinse aid indicator light
Alternatively, you can judge the amount of rinse aid by checking the rinse
aid indicator right next to the reservoir’s cap. When the indicator is black, it
means it is full. When it is clear, it means it is almost empty.
GB-14
Logik LDW6TTW_IB_GB_090605.indd 14
05/06/09 3:32:41 PM
Adjusting Rinse Aid Reservoir
The rinse aid reservoir has six settings. Both the recommended setting and
the factory setting is “4.” (Fig 2b on page 14)
If the dishes are not drying properly or are spotted, adjust the dial to the next
higher number until your dishes are spot-free.
Adding of Salt
If the water in your area is hard, deposits will form on your dishes and utensils.
As such, this appliance contains a salt
reservoir for you to reduce the hardness
of the water.
1
open
open
Operating Instructions
OPEN
Please follow the steps below to pour
the salt into the salt reservoir and it
must be set to correspond to the water
hardness level in your area.
1. Remove the lower basket and unscrew the reservoir cap. (Fig 1)
2. Fill the reservoir with approximately
500ml of water (first use only).
3. Place the funnel provided over the
salt reservoir. (Fig 2)
4. Place approximately 1.2kg of salt
depending on the brand used.
5. Clean any excess salt from around
the reservoir opening and then
screw the cap on again firmly.
6. Run the “eco” wash programme
immediately (without any crockery
in the dishwasher) to remove any
traces of salt from the compartment.
open
2
GB-15
Logik LDW6TTW_IB_GB_090605.indd 15
05/06/09 3:32:42 PM
The salt indicator light on the display
window will illuminate when the reservoir is running out of salt and required
re-filling.
Salt indicator on the display window
The salt indicator light will cease to illuminate within a few days depending
on how quickly the salt dissolves.
GB-16
Logik LDW6TTW_IB_GB_090605.indd 16
05/06/09 3:32:42 PM
Loading the Dishwasher
Before loading the
Dishwasher
1
In general, please observe the following notes prior loading your
cutlery and crockery in the basket.
•
•
•
•
•
•
•
Operating Instructions
•
Remove lipstick stains and coarse
food residues from crockery and
dishes. Rinse if necessary. (Fig 1)
Dishes and Cutlery must not lay
inside one another, or cover each
other.
Load your cutlery and crockery so
that water can access all surfaces.
(Fig 2)
Ensure all items are securely positioned.
2
Hollow items such as cups, glasses,
pans, etc. must be placed upside
down in the basket.
Wide based items should be placed
at an angle so that water can run off
them freely.
The spray arms must not be blocked
by items which are too tall or hang through the baskets. If in doubt, test
for free movement by manually rotating the spray arms.
Ensure that small items cannot fall through the holders in the baskets.
CAUTION: Do not wash items soiled with ash, sand, wax, lubricating
grease or paint in the dishwasher. Ash does not dissolve
and can distribute in the dishwasher. Wax, sand, lubricating
grease and paint can cause damage to the dishwasher.
GB-17
Logik LDW6TTW_IB_GB_090605.indd 17
05/06/09 3:32:43 PM
For safety reasons, do not operate the dishwasher without the
dishwasher basket in place.
Dishwasher basket
1
Please use the dishwasher basket for
small and lightweight items such as
cups, saucers, glasses, dessert bowls,
etc. Shallow pans or casserole dishes
can also be placed in the basket. (Fig 1)
Long items such as soup ladles, mixing
spoons and long knives (Fig 2) should
be placed lying down across the front of
the basket.
2
Hinged Cup Rack
To make room for taller items in the upper basket, raise the cup rack upwards.
(Fig 3) You can lean the tall glasses
against it. You can also remove it when
it is not required for use.
3
Raise upwards
Raise upwards
TIP: To prevent water dripping from the
upper basket onto the dishes in the
lower basket, we recommend that you
empty the lower basket first and then
the upper basket.
Fold backwards
4
Hinged Spikes
The spikes are used for holding plates
and platter. They can be lowered to
make more room for large items. Please
refer to Fig 4 for the steps to lower the
spikes.
Push and snap
GB-18
Logik LDW6TTW_IB_GB_090605.indd 18
05/06/09 3:32:45 PM
Loading the basket for 6 place settings
For placement method of the upper basket, please refer to the table below
and Fig 1.
1
IN
6
1
3
4
5 10
7
8
9
3
2
1
2
Cups
Larg e se rving bowl
3
4
G lasses
Sa ucers
5
6
Dish
O val plat ter
7
8
Dinner plates
Soup pla tes
9
Operating Instructions
Dessert dishe s
10
Cutlery basket
GB-19
Logik LDW6TTW_IB_GB_090605.indd 19
05/06/09 3:32:48 PM
Cutlery Basket
Loading the Cutlery Basket
To make unloading much easier, cutlery
should be grouped in zones and placed
in the cutlery basket. Please refer to the
table below and Fig 1 for placement
method.
Number
Item
1
Forks
2
Soup spoons
3
Dessert spoons
4
Teaspoons
5
Knives
6
Serving spoons
7
Gravy ladle
8
Serving fork
WARNING!
Do not let any items extend through the
bottom of baskets. (Fig 2)
To avoid the risk of injury, please load
your knives and forks with handles upwards. Do not hold them by their sharp
edges. (Fig 3)
The cutlery basket comes with covers,
and they are designed for you to load
the cutlery into appropriate slots. If
you use the basket without the cover, it
may reduce the washing result of your
cutlery.
IN
1 4 5 2
1 4 5
1 4 5 2
1 4 5 2
1 4 5
4 4 5 2
1
7 4 5 2
8 3 5
1 3 3 2
1 3 3 2
1 3 3
6 3 6 2
2
3

Please ensure the cover is securely
locked to the basket before operation.
*To comply with Standards of
Performance, i.e. EN50242, please
ensure all the cutlery must be loaded
according to the instruction in this
manual.
GB-20
Logik LDW6TTW_IB_GB_090605.indd 20
05/06/09 3:32:50 PM
Starting a Wash Cycle
Please follow the steps below to start a wash cycle.
1. Ensure the unit is connected to the mains power and the water supply is
fully opened (water pressure between 0.04MPa and 1.00MPa).
2. Open the door. Pull out the dishwasher basket, load the dishes and
push the baskets back.
3. Pour in the detergent or place the detergent tablet in the detergent
compartment. Ensure the lid is firmly closed afterward.
4. Close the dishwasher door. A click sound should be heard when the
door is closed correctly. Do not slam the door.
5. Press ON/OFF button.
6. Select the wash cycle programme based on the loading and soil requirements. Please refer to the “Wash Cycle Table” (page 11).
7. The power indicator light and the selected programme indicator light
will illuminate.
8. Press the Start/Pause button and the washing cycle will begin shortly.
Operating Instructions
NOTE: If you open the dishwasher’s door during the washing cycle and then
close it, the dishwasher will continue the current washing programme after
10 seconds. However, if the door is not closed correctly after 1 minute, the
dishwasher will make an audible sound at 1 minute intervals.
Changing a Programme
To change the programme if the washing cycle has already started, please
follow the steps below.
1. Open the door slightly to check if the unit has dispensed the detergent
or detergent tablet. This will depend on how long the washing cycle
was running for.
2. If the detergent dispenser lid is opened, we suggest you to allow the
wash cycle to complete.
3. If the detergent dispenser lid is still closed, press On/Off button to cancel the programme. You may then close the dishwasher door and press
On/Off button again. Then, press the required new programme button
and confirm the selection by pressing Start/Pause button. The unit will
start the new washing cycle shortly.
GB-21
Logik LDW6TTW_IB_GB_090605.indd 21
05/06/09 3:32:50 PM
At the End of a Programme
At the end of a programme, the unit will sound.
Switching off the Unit
For energy saving, please remember to switch the dishwasher off using
the “off” button. The dishwasher will continue to use electricity until it is
switched off with the “off” button.
If the dishwasher is not going to be used for a long period of time, e.g.
whilst on holiday, please disconnect the unit from the mains supply.
Unloading the Dishwasher
Allowing dishes to cool down before unloading is important because
dishes tend to break and chip more easily when they are hot. Therefore, if
you open the dishwasher door fully after switching off this will allow the
dishes to cool down much faster.
GB-22
Logik LDW6TTW_IB_GB_090605.indd 22
05/06/09 3:32:50 PM
Cleaning After Use
External Care
The Door and the Door Seal
•
•
Clean the door seals regularly with a soft damp cloth to remove food
deposits.
When the dishwasher is being loaded, food and drink residues may drip
onto the sides of the dishwasher door. These surfaces are outside the
wash cabinet and are not accessed by water from the spray arms. Any
deposits should be wiped off these surfaces before the door is closed.
The Control Panel
•
If cleaning is required, the control panel should be wiped with a soft
damp cloth ONLY.
ATTENTION: To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind.
Never use abrasive cleaners or scouring pads on the outer surfaces because
they may scratch the finish. Some paper towels may also scratch or leave
marks on the surface.
Internal Care
Filtering System
Please follow the steps below to clean
the filters in the wash cabinet.
•
•
Care, Maintenance
and Troubleshooting
The filtering system in the base of the wash cabinet retains coarse soil from
the suds solution. Collection of coarse soil may cause the filters to clog.
Check the condition of the filters regularly and clean them if necessary
under running water.
1
Close
Ensure the dishwasher is switched
off.
Unscrew the coarse and fine filter.
(Fig 1)
GB-23
Logik LDW6TTW_IB_GB_090605.indd 23
05/06/09 3:32:55 PM
•
Gently lift the coarse and fine filter
out. (Fig 2)
• Gently lift the main filter with care.
• Rinse all the filters under running
water, including the filter cylinder
(Fig 3), and then refit all filters in the
following order.
• Gently refit the main filter back with
care. (Fig 4)
• Gently rescrew the course and fine
filter in clockwise direction. (Fig 1 on
Page 23)
NOTE: Do not over tighten the filters.
• Put the filters back to the filter cylinder in sequence securely. Otherwise
coarse soil could get into the system
and cause a blockage.
Coarse and Fine Filter
2
Main Filter
Filter cylinder without the filters
WARNING!
NEVER use the dishwasher without
filters in place. Improper replacement of
the filter may reduce the performance
level of the appliance and damage
dishes and utensils.
3
4
Slide in
Push
down
Spray Arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be checked and
cleaned regularly. (Fig 1)
•
1
Use a pointed object, for instance a
cocktail stick, to loosen food particles in the spray arms’ jets.
NOTE: Do not attempt to remove the spray arms.
GB-24
Logik LDW6TTW_IB_GB_090605.indd 24
05/06/09 3:32:59 PM
Frost Precaution
Avoid placing the dishwasher in a location where temperature is below 0◦C.
If your appliance is left in an unheated place over the winter, please do the
following:
1. Disconnect from the mains.
2. Empty the dishwasher.
3. Close the dishwasher’s door.
4. Disconnect the unit from the water inlet and drain. Use a suitable receptacal to catch the water.
Should you encounter difficulties to do the above steps, please ask a service
technician for assistance.
Moving the Dishwasher
If you have to move the unit, for instance due to moving house, please do
the following:
1. Disconnect the dishwasher from the mains.
2. Disconnect the unit from the water inlet and drain.
3. Remove the unit from the current location with the hoses discharged.
4. Pull the unit out together with the hoses.
NOTE: Avoid over tilting the unit during transportation.
Maintenance After Prolonged Period of
Non-Operation
Care, Maintenance
and Troubleshooting
If you are not going to use the unit for any prolonged period of time, you
are advised to:
1. Disconnect the dishwasher from the mains.
2. Disconnect the unit from the water inlet and drain. Use a suitable receptacal to catch the water.
3. Slightly open the door to prevent unpleasant smells building up in the
compartment.
4. Ensure the washing compartment of the unit is clean.
GB-25
Logik LDW6TTW_IB_GB_090605.indd 25
05/06/09 3:32:59 PM
Troubleshooting Guide
Repairs should only be carried out by a qualified technician in
strict accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage to the unit.
fault code
Codes
3 in 1 program light
is blinking
Rinse light
is blinking
Possible Causes
Water tap is not turned on.
Low water pressure
(<0.04MPa)
Flow meter is broken.
The wire terminals which
connect the flow metre are
loose.
The float switch is broken or
PCB is faulty.
The wire terminal connected
to the float switch is loose or
broken.
Remedy
Turn on the water tap.
Turn on the water tap and ensure full opening position.
•
•
•
Disconnect from the
mains.
Disconnect the water inlet.
Call a qualified technician.
GB-26
Logik LDW6TTW_IB_GB_090605.indd 26
05/06/09 3:32:59 PM
Technical Problems
Technical problems
Problem
The dishwasher does
not start.
The drain pump is not
working properly.
General problems
Problem
Detergent residue is
left in the dispenser at
the end of the programme.
The detergent dispenser lid cannot be closed
properly.
Knocking noise in the
wash cabinet.
The anti-flooding system has operated.
Remedy
Close the door firmly.
Insert the plug to the
mains.
Press the “on” button and select a programme.
• Disconnect from
the mains.
• Disconnect the
water inlet.
• Call a qualified
technician.
Possible Causes
The detergent dispenser was still damp when
detergent was added.
Remedy
Make sure the dispenser is dry before adding
detergent.
Clogged detergent
residue is blocking the
catch.
A spray arms is knocking against an item in a
basket.
Clean the catch.
The rinse aid dosage is
set too high.
Interrupt the programme, and rearrange
the items which are
obstructing the spray
arm. See the section
“loading the diswasher”.
Adjust the dial of the
rinse aid dispenser to a
lower setting.
Care, Maintenance
and Troubleshooting
Smearing appears on
glassware and cutlery.
Possible Causes
The door is not properly closed.
The unit is not connected to the mains.
The unit is not
switched on.
GB-27
Logik LDW6TTW_IB_GB_090605.indd 27
05/06/09 3:32:59 PM
General problems (continue)
Problem
Possible Causes
The amount of rinse
aid may be insufficient,
or the rinse aid reservoir is almost empty.
Dishes, cutlery and
glasses are not dry.
Crockery was taken out
of the dishwasher too
soon.
Not enough rinse aid
was used.
White residue is visible on cutlery and
crockery, clouding
occurs on glassware;
film can be wiped off.
There is not enough
salt in the salt reservoir.
The salt reservoir cap
has not been screwed
on correctly.
Unsuitable detergent
has been used.
Glassware is dull and The glassware is not
discoloured; film can- dishwasher proof. The
not be wiped off.
surfaces are affected.
Tea or lipstick stains
have not been completely removed.
The wash temperature
of the selected programme was too low.
The bleaching effect of
the detergent used is
too low.
Forgot to pre-rinse or
remove the stains with
napkin prior washing.
Remedy
Replenish the reservoir, adjust the rinse aid dispenser
dial to a higher setting or
change the brand of rinse
aid.
Leave the crockery in the
dishwasher until you hear
the audible sound.
Replenish the reservoir, adjust the rinse aid dispenser
dial to a higher setting or
change the brand of rinse
aid.
Fill the salt reservoir.
Ensure that it screws back
on correctly.
Change your detergent.
Use a dishwasher standard powder detergent or
tablet.
Wash the non-dishwasher
proof glassware by hand
instead.
Select a programme with a
higher wash temperature.
Change your detergent.
Pre-rinse or remove the
stains with napkin prior
washing.
GB-28
Logik LDW6TTW_IB_GB_090605.indd 28
05/06/09 3:32:59 PM
Specification
Dimension:
550 (W) x 500 (D) x 438 (H)
(in mm)
Capacity:
6 Place Settings
Water Pressure Required:
0.04 - 1.00MPa
Power Consumption:
1280W
Rated Voltage:
230V/50Hz
Because we continually strive to improve our products we may change specifications and designs
without prior notice.
Care, Maintenance
and Troubleshooting
GB-29
Logik LDW6TTW_IB_GB_090605.indd 29
05/06/09 3:33:00 PM
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste.
It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health deriving from an inappropriate disposal and enables the constituent materials to be recovered
to obtain significant savings in energy and resources. As a reminder of
the need to dispose of household appliances separately, the product is
marked with a crossed-out wheeled dustbin.
Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories.
With over 1 million spares and accessories available we can deliver direct to your door
the very next day.
Visit www.partmaster.co.uk
or call
0870 6001 338
(UK customers only)
Calls charged at National Rate.
NOTE: If you require a replacement for a replacement for any of the items listed
below, please quote their corresponding part numbers:
Replacement Part
Part Number
Water Supply Hose
673005400045
Detergent Measuring Spoon (approx. 20g)
673002200079
Measuring cup (approx. 60ml)
673006200004
U-shape Hose holder
673006200003
Salt Funnel
673002200001
Drain Hose
673005400041
Drain Hose Mounting Clamp
672005400002
Cutlery Basket with Covers
673006200014
Instruction Manual
675005900815
Installation Guide
675005900823
DSG Retail Limited is responsible for after sales service.
If you have a query about the product please contact our product support line
08701 565 550 (Currys).
GB-30
Logik LDW6TTW_IB_GB_090605.indd 30
DSG Retail • 200 The Campus • Marylands Avenue •
Hemel Hempstead • Herts • HP2 7TG
05/06/09 3:33:00 PM
Logik LDW6TTW_IB_GB_090605.indd 31
05/06/09 3:33:00 PM
Logik LDW6TTW_IB_GB_090605.indd 32
05/06/09 3:33:00 PM