User’s Manual
OLS1000ERT(XL)2U
OLS1500ERT(XL)2U
OLS2000ERT(XL)2U
OLS3000ERT(XL)2U
CyberPower Systems Inc.
www.cyberpower.com
K01-C000113-02
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the
unit. Read this manual thoroughly before attempting to unpack, install, or operate the UPS.
CAUTION! The UPS must be connected to a grounded AC
power outlet with fuse or circuit breaker protection. DO NOT
plug the UPS into an outlet that is not grounded. If you need to
power-drain this equipment, turn off and unplug the unit.
cause damage to your equipment and cause fire hazards.
CAUTION! Wiring must be done by qualified personnel.
CAUTION!
DO NOT USE FOR MEDICAL OR LIFE
SUPPORT EQUIPMENT! Under no circumstances this unit
should be used for medical applications involving life support
equipment and/or patient care.
CAUTION! The battery can power hazardous components
inside the unit, even when the AC input power is disconnected.
CAUTION! The UPS should be placed near the connected
equipment and easily accessible.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS!
To reduce the risk of fire, do not use with or near aquariums.
Condensation from the aquarium can come in contact with
metal electrical contacts and cause the machine to short out.
CAUTION! To prevent the risk of fire or electric shock, install
in a temperature and humidity controlled indoor area, free of
conductive contaminants. (Please see specifications for
acceptable temperature and humidity range).
CAUTION! Do not dispose of batteries in fire as the battery
may explode.
CAUTION! (No User Serviceable Parts): Risk of electric
shock, do not remove cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.
CAUTION! Do not open or mutilate the battery, released
electrolyte is harmful to the skin and eyes.
CAUTION! A battery can present a risk of electric shock and
high short circuit current. The following precaution should be
observed when working on batteries
CAUTION! (Non-Isolated Battery Supply): Risk of electric
shock, battery circuit is not isolated from AC power source;
hazardous voltage may exist between battery terminals and
ground. Test before touching.
1. Remove watches, rings or other metal objects.
CAUTION! To reduce the risk of fire, connect the UPS to a
branch circuit with 10 amperes (OLS1000 / OLS1500) / 16
amperes (OLS2000/ OLS3000) maximum over-current
protection in accordance to CE requirement.
2. Use tools with insulated handles.
CAUTION! The AC outlet where the UPS is connected should
be close to the unit and easily accessible.
CAUTION! The unit has a dangerous amount of voltage.
When the UPS indicators is on, the units may continue to
supply power thus the unit’s outlets may have a dangerous
amount of voltage even when it’s not plugged in to the wall
outlet.
CAUTION! Please use only VDE-tested, CE-marked mains
cable, (e.g. the mains cable of your equipment), to connect the
UPS to the AC outlet.
CAUTION!
Make sure everything is turned off and
disconnected completely before conducting any maintenance,
repairs or shipment.
CAUTION! Please use only VDE-tested, CE-marked power
cables to connect any equipment to the UPS.
CAUTION!
Connect the Protection Earth (PE) safety
conductor before any other cables are connected.
CAUTION! When installing the equipment, ensure that the
sum of the leakage current of the UPS and the connected
equipment does not exceed 3.5mA.
WARNING! (Fuses): To reduce the risk of fire, replace only
with the same type and rating of fuse.
DO NOT INSTALL THE UPS WHERE IT WOULD BE
EXPOSED TO DIRECT SUNLIGHT OR NEAR A STRONG
HEAT SOURCE!
CAUTION! The OLS1000 / OLS1500 / OLS2000 / OLS3000 /
Battery module models are only qualified maintenance
personnel may carry out installations.
DO NOT BLOCK OFF VENTILATION OPENINGS AROUND
THE HOUSING!
CAUTION! Do not unplug the unit from AC Power during
operation, as this will invalidate the protective ground
insulation.
DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS
HAIR DRYERS TO UPS OUTPUT SOCKETS!
CAUTION! To avoid electric shock, turn off and unplug the
unit before installing the input/output power cord with a ground
wire. Connect the ground wire prior to connecting the line
wires!
CAUTION!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR
SUPERVISED BY PERSONNEL KNOWLEDGE OF
BATTERIES AND THE REQUIRED PRECAUTIONS. KEEP
UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES!
Do not use an improper size power cord as it may
Copyright © 2016 CyberPower Systems, Inc.
1
HARDWARE INSTALLATION
Output power cords x2pcs
Flat head screws: M4X8L (8)
UPS
Pan head screws: M5X12L (12)
Plastic washers (8)
User’s manual
Screw hole dust covers (8)
Phone line
USB communication cable
Rackmount ears (Stands) (2)
PowerPanel® Personal Edition software is available on our
website. Please visit www.cyberpower.com and go to the
Software Section for free download.
Input power cord
Rackmount left rail
Rackmount right rail
Copyright © 2016 CyberPower Systems, Inc
.
2
HARDWARE INSTALLATION
HARDWARE INSTALLATION
These versatile UPS systems can be mounted in a
rackmount or vertical tower orientation. This versatility is
especially important to growing organizations with changing
needs that value having the option to position a UPS on a
floor or in a rackmount system. Please follow the instructions
below for the respective mounting methods.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only
use the supplied hardware to attach the mounting brackets.
RACKMOUNT INSTALLATION
2)
Step 1: Rackmount ears installation
Attach the rackmount rail to your rack with two M5X12L
screws and two plastic washers at the front of the rack.
Attach the two rackmount ears to the UPS using the
(Located in position 1 & position 6) Do not tighten the
provided screws M4X8L*8pcs.
screws. Adjust the rail size on the rail assembly of your
rack. Secure the rail to the rear of the rack with two
M5X12L screws and two plastic washers. Tighten all
screws at the front and rear of the rail. Once completed,
perform the same steps for assembling the other
rackmount trail.
Step 2: Rackmount rails Installation
1)
The rails adjust to mount in 48-cm (19-inch) panel racks
from 52 to 91.5cm (20.5 to 36 inches) deep. Select the
proper holes in the rack for positioning the UPS in the
rack. The UPS takes up position 1 through position 6.
Copyright © 2016 CyberPower Systems, Inc.
3
HARDWARE INSTALLATION
Step 3: Install the UPS on the rack
Place the UPS on a flat stable surface with the front of the
unit facing toward you. Secure the UPS to your rack with
four M5X12L screws at the front of the rack. (Located in
position 2 & position 5).
Step 2: Attach the base stands
Tighten the screws (M5X12*4pcs) of the base stands
(rackmount ears) onto the bottom of the UPS.
VERTICAL/TOWER INSTALLATION
Step 1: Rotate the Multifunction LCD Module
1) Unscrew the right panel of the UPS. Separate the right
panel from the UPS.
Step 3: Attach dust covers
Insert dust cover into the rackmount ear screw holes that are
not being used.
2)Unscrew the LCD plate , Gently lift the LCD module out.
Rotate it to the tower orientation. Reinstall it for a tower
configuration .Attach the LCD plate and LCD module to the
right panel using the provided screws.
Copyright © 2016 CyberPower Systems, Inc.
4
HARDWARE INSTALLATION
ELECTRICAL INSTALLATION
After completing the hardware installation of the UPS, you are now ready to plug in the UPS and connect your equipment.
SAFETY PRECAUTIONS
CAUTION!
Installation environment should be in a temperature and humidity controlled indoor area free of conductive
contaminants. Do not install this UPS where excessive moisture or heat is present (Please see specifications for acceptable
temperature and humidity range).
CAUTION!
Never install a UPS, or associated wiring or equipment, during a lightning storm.
CAUTION!
Do not work alone under hazardous conditions.
CAUTION! In case of the risk of electric shock, do not remove the top cover.
CAUTION! The battery can energize hazardous live parts inside even when the AC input power is disconnected.
Copyright © 2016 CyberPower Systems, Inc.
5
INSTALLING YOUR UPS SYSTEM
SYSTEM BLOCK DIAGRAM
Bypass
Input
Input
Filter
PFC
AC/DC
BUS
Charger
AC/DC
Battery
DC/DC
Inverter
DC/AC
Control
&
Monitoring
INV
RY
Output
Filter
Output
LCD Module
USB & DB9
SNMP Slot
Line Mode
Battery Mode
Bypass Mode
HARDWARE INSTALLATION GUIDE
1. Battery charge loss may occur during shipping and storage.
7. To maintain an optimal battery charge, leave the UPS
Before using the UPS, it’s strongly recommended to charge
batteries for four hours to ensure the batteries’ maximum
charge capacity. To recharge the batteries, simply plug the UPS
into an AC outlet.
plugged into an AC outlet at all times.
8. Before storing the UPS for an extended period of time, turn
the unit OFF. Then cover it and store it with the batteries fully
charged. Recharge the batteries every three months to ensure
good battery capacity and long battery life. Maintaining a good
battery charge will help prevent possible damage to the unit
from battery leakage.
2. When using the included software, connect either the serial
or the USB cable between the computer and the corresponding
port on the UPS. Note: If the USB port is used, the serial port
will be disabled. They cannot be used simultaneously.
9. The UPS has one USB port (default) and one Serial port that
3.
Connect
your
computer,
monitor,
and
any
externally-powered data storage device (Hard drive, Tape drive,
etc.) into the outlets only when the UPS is off and unplugged.
DO NOT plug a laser printer, copier, space heater, vacuum,
paper shredder or other large electrical device into the UPS.
The power demands of these devices will overload and
possibly damage the unit.
allows connection and communication between the UPS and
®
any attached computer running the PowerPanel Business
Edition Agent software. The UPS can control the computer’s
shutdown during a power outage through the connection while
the computer can monitor the UPS and alter various
programmable parameters. Note: Only one communication
port can be used at a time. The port not in use will automatically
become disabled or the serial port will be disabled if both ports
are attached.
4. To protect a fax machine, telephone, modem line or network
cable, connect the telephone or network cable from the wall
jack outlet to the jack marked “IN” on the UPS and connect a
telephone cable or network cable from the jack marked “OUT”
on the UPS to the modem, computer, telephone, fax machine,
or network device.
10. EPO (Emergency Power Off) / ROO(Remote on/off) Port:
EPO/ROO ports allow administrators the capability to connect
the UPS unit to customer-supplied EPO/ROO switches. If EPO
is enabled, these installations give operators a single access
point to immediately power-off all equipment connected to the
UPS during an emergency. If ROO is enabled, these
installations give operators a access point to turn on/off UPS
remotely.
5. Press the ON switch to turn the UPS on. If an overload is
detected, an audible alarm will sound and the UPS will
continuously emit one beep per second. For resetting the unit,
unplug some equipment from the outlets. Make sure your
equipment carries a load current within the unit’s safe range,
(refer to the technical specifications).
11. To avoid electric shock, turn the unit OFF and disconnect
the unit from utility power before hardwiring the UPS (in/out
power cord). The in/out power cord MUST be grounded.
6. This UPS is equipped with an auto-charge feature. When the
UPS is plugged into an AC outlet, the battery will automatically
charge, even when the unit is switched off.
Copyright © 2016 CyberPower Systems, Inc.
6
BASIC OPERATION
POWER MODULE FRONT/REAR PANEL DESCRIPTION
1. Power On/Off Button
Master ON/OFF for the UPS.
2. Function Buttons
Scroll up, scroll down, select and cancel LCD
menu.
3. Multifunction LCD Readout
Indicate status information, settings and events.
4. Input Circuit Breaker
Provide input overload and fault protection.
5. Battery Backup & Surge Protected Outlets
Provide battery backup and surge protection.
They ensure power is provided to connected
equipment over a period of time during a power
failure.
6. Serial Port
Serial port provides communication between the
UPS and the computer. The UPS can control the
computer’s shutdown during a power outage
through the connection while the computer can
monitor the UPS and alter its various
programmable parameters.
OLS1000ERT(XL)2U, OLS1500ERT(XL)2U
7. USB port
This is a connectivity port which allows
communication and control between the UPS
and the connected computer. It is recommended
to install the PowerPanel® Business Edition
Agent software on the PC/Server connected
with the USB cord.
8. Surge Protected Communication Ports
RJ-45/RJ-11
These ports are used to protect standard
RJ-45/RJ-11 based products (ADSL, LAN,
Phone/ Modem-Lines) and cabling systems from
surges.
OLS2000ERT(XL)2U
9. SNMP/HTTP Network slot
Slot to install the optional SNMP card for remote
network control and monitoring.
10. Extended Runtime Battery Module
Connector
Connect to additional external battery modules.
11. EPO (Emergency Power Off) Connector
Enable Power-Off in emergency from a remote
location.
12. AC Input Inlet
Connect the AC Power cord to a properly wired
and grounded outlet.
13. Output Circuit Breaker
Provide overload and fault protection.
OLS3000ERT/ERT(XL)2U
Copyright © 2016 CyberPower Systems, Inc.
7
8
BASIC OPERATION
BATTERY MODULE FRONT/REAR PANEL DESCRIPTION
1. Input Connector
Use this input connector to daisy chain the next Battery module.
Remove the connector cover for access.
2. On-board Replaceable Fuse Cover
Replaceable fuse is accessible from the rear panel.
It must be done by qualified personnel.
3. Output Connector
Use this output Connector to connect the Battery module to
the Power module or to the next Battery module.
BPSE36V45ART2U, BPSE72V45ART2U
CONNECTION 1 : POWER MODULE WITH ONE BATTERY MODULE
Step 1: Loosen the two screws to remove the
battery cable retention bracket of the
power module.
Step 2: Use the battery cable of the Battery
module to connect the Battery module
to the Power module.
Step 3: Rotate the battery cable retention racket
and tighten the two screws to fix battery
cable.
CONNECTION 2 : POWER MODULE WITH MULTIPLE BATTERY MODULES
st
Step 1: Connect the 1 Battery module to the Power
module using battery cable.
Step 2: Loosen the two screws to remove the battery
st
cable retention bracket of the 1 battery module.
Step 3: Use the battery cable to connect the 2
st
module to the 1 Battery module.
nd
Battery
Step 4: Rotate the battery cable retention bracket and
tighten the two screws to fix battery cable.
Copyright © 2016 CyberPower Systems, Inc.
8
BASIC OPERATION
LCD SCREEN – UPS STATUS
LCD Screen
UPS Status Description
UPS is operating in Line Mode.
UPS is operating in Battery Mode.
UPS is operating in Bypass Mode.
UPS is operating in ECO (Economy) Mode.*
UPS is operating in Converter Mode when this icon blinking**.
*) When operating in ECO Mode, the efficiency of UPS is higher than that in online mode, but transfer time should not be 0ms
**) When operating in Converter Mode, the frequency of output should be always 50Hz or 60Hz, but load capacity will be
derated.
DEFINITIONS FOR OTHER ICONS
LCD Screen
Description
LOAD capacity: This meter displays the approximate output
load level (in 20% increments) of the UPS outlets.
BATTERY capacity: This meter displays the approximate
charge level (in 20% increments) of the UPS’s internal
battery. During a blackout or severe brownout, the UPS
switches to battery power, the BATTERY icon appears, and
the charge level decreases.
MUTE: This icon appears whenever the UPS is in silent
mode. The alarm does not beep during silent mode until the
battery reaches low capacity.
SCHEDULE: Users can setup the schedule to turn on and
shut down the computer and UPS through PowerPanel®
Personal Edition software. The LCD display will show how
much time is left before the UPS will turn back on or shut
down.
OVER LOAD: This icon appears and an alarm sounds to
indicate the outlets are overloaded. To clear the overload,
unplug some of your equipment from the battery-supplied
outlets until the icon turns off and the alarm stops.
FAULT: This icon appears if there is a problem with the UPS.
Please refer to “Event ID Descriptions”.
Copyright © 2016 CyberPower Systems, Inc.
9
BASIC OPERATION
REPLACE: This icon appears if the batteries need to be
replaced.
Event ID Descriptions
Event ID
Description of Cause
1
Bus Start Fail: DC-DC converter or bus sensing circuit failed.
2
Bus Volt High: DC-DC converter failed.
3
Bus Volt Low: DC-DC converter failed.
4
Bus Unbalanced: DC-DC converter failed.
5
INV Start Fail: Inverter circuit failed.
6
7
INV Volt High: Inverter circuit or output voltage sensing
circuit failed.
INV Volt Low: The load may be too heavy or inverter circuit
failed.
8
INV Short: The inverter circuit failed.
9
Bat Volt High: The external battery module connection is
wrong, or the charger failed.
10
Bat Volt Low: Batteries failed.
11
Over Temperature: High ambient temperature, or the
ventilation hole has been covered.
12
Over Load: UPS is overloaded.
54
High Temperature: High ambient temperature, or the
ventilation hole has been covered. This is shown only when
start up UPS.
55
Bat Low: Battery voltage is too low to DC start UPS.
57
EPO Off: Missing the EPO connection
58
Fan Fail: The ventilation hole has been covered, or the fans
can’t work.
59
Bat Bad: Battery failed.
BUTTON OPERATION
Button
Operation Description
ON
Press this button to turn on UPS.
OFF
Press this button to turn off UPS.*
Press this button to scroll up in the LCD menu.
Press this button simultaneously for 5 seconds to disable or
enable the alarm system while in battery mode.
Press this button simultaneously for 5 seconds to enter UPS
ENTER/▲
self-testing while in AC mode, ECO mode, or converter mode.
In setting mode, press this button to confirm selection, or
press this button for long time to exit setting mode and saving
changes.
Press this button to scroll down in the LCD menu.
Press this button for long time to get into setting mode
In setting mode, press this button to display next selection, or
ESC/▼
press this button for long time to exit setting mode without
saving changes.
Switch to bypass mode: When the main power is normal,
press these two buttons simultaneously for 5 seconds, then
ENTER/▲ + ESC/▼
UPS will enter to bypass mode.
*) If utility power is connected,UPS will keep charging but cut off output.
Copyright © 2016 CyberPower Systems, Inc.
10
LCD SETUP FUNCTIONS
LCD INFORMATION READOUT
There are 12 types of UPS information available for display on digit area.
Information Submenu
Description
OUTPUT
XXX V
Displays the Output Voltage
OUTPUT
XX.XHz
Displays the Output Frequency
OUTPUT
XXX (k)VA
Displays the Output VA
OUTPUT
XXX% VA
Displays the Output Load Percentage of Maximum Apparent Power
OUTPUT
XXX (k)W
Displays the Output Wattage
OUTPUT
XXX% W
Displays the Output Load Percentage of Maximum Active Power
INPUT
XXX V
Displays the Input Voltage
EVENT
XXX
Displays the Event ID
ESTIMATED RUN TIME
%
ESTIMATED RUN TIME
XX(.)X [Min][Hr]
TIME TO SHUT DOWN
XX(.)X [Min][Hr]
TIME TO TURN ON
XX(.)X [Min][Hr]
Displays the Estimated Percentage of Battery Capacity
Displays the Estimated Run Time with battery
Displays the Time Delay to Shutdown UPS
Displays the Time Delay to Restart UPS
LCD SETTINGS CONFIGURATION
There are 8 UPS settings that can be configured by the user.
1. Press the “ESC” button simultaneously for 5 seconds to activate the setting mode.
The first configuration parameter will be displayed on the LCD screen.
Note: The manual settings programming mode can ONLY be invoked while UPS is in Bypass mode or Standby mode. To
make UPS on Standby mode or Bypass mode, connect utility power to UPS and do not turn on UPS.
2.
Press the “ENTER” button to select the setting you want to configure.
3.
Press the “▼” buttons to scroll through the different parameters.
Press the “ENTER” button to select the parameter you want.
4.
Press the “ESC” button simultaneously for 5 seconds to cancel and exit setting mode. Press the “ENTER” button
simultaneously for 5 seconds to save all the settings you just do and exit setting mode.
Copyright © 2016 CyberPower Systems, Inc.
11
LCD SETUP FUNCTIONS
Configure Submenu
Available Settings
Default Setting
Output Voltage
= [208V] [220V] [230V] [240V]
230V
Output Frequency
= [50Hz][60Hz]
50Hz
ECO Mode *
[0%] (Disable) [10%][15%] (Enable)
0%
Bypass Mode **
[DIS] (Disable) [ENA] (Enable)
Enable
Converter Mode
[DIS] (Disable) [ENA] (Enable)
Disable
EPO/ROO***
[EPo] [Roo]
EPO
EBM Number****
[0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10](for –E models, the
maximum number is 3 )
0(for –E models) / 1 (for –EXL models)
Bypass when UPS
is Off
[F1d](Disable)[F1E](Enable)
Disable
*) This function would be set as 0% when Converter Mode is enabled.
**) UPS has no bypass when Converter Mode is enabled.
*** ROO (Remote On/Off): If ROO is enabled, UPS can be turn on/off by the ROO port. If ROO port is disconnected, UPS
will be turned off. If ROO port is connected, UPS will be turned on when the utility is normal
****) UPS cannot detect the numbers of external battery automatically, so manual input from user is necessary.
SILENCING AUDIBLE ALARMS
Press the “ENTER” button on simultaneously for 5 seconds to disable or enable the alarm system while in battery mode.
Note: Some audible alarms (Over Temperature, Fan Fail, etc.) can’t be silenced.
MANUAL BATTERY TEST
Press the “ENTER” button simultaneously for 5 seconds to enter UPS self-testing while in AC mode, ECO mode, or
converter mode.
Copyright © 2016 CyberPower Systems, Inc.
12
MAINTENANCE
Storage
To store your UPS for an extended period, cover it and store
with the battery fully charged. Recharge the battery every
three months to ensure battery life.
CAUTION! To avoid electric shock, turn off and unplug the
UPS from the wall receptacle before servicing the battery.
CAUTION! Only use tools with insulated handles. Do not
lay tools or metal parts on top of the UPS or battery terminals.
Safety Precautions
Replacement Batteries
CAUTION! Only use replacement batteries which are
certified by CyberPower Systems. Use of incorrect battery
type is an electrical hazard that could lead to explosion, fire,
electric shock, or short circuit.
CAUTION! Batteries contain an electrical charge that can
cause severe burns. Before servicing batteries, please
remove any conductive materials such as jewelry, chains,
wrist watches, and rings.
Please refer to the front side of the UPS for the model
number of the correct replacement batteries. For battery
procurement, log onto www.cyberpower.com, or contact your
local dealer.
Battery Disposal
Batteries are considered hazardous waste and must be
disposed of properly. Contact your local government for more
information about proper disposal and recycling of batteries.
Do not dispose of batteries in fire.
CAUTION!
Do not open or mutilate the batteries.
Electrolyte fluid is harmful to the skin/eyes and may be toxic.
Battery Installation and replacement
Step 3: Fasten the battery bracket and then insert the
connectors. Place the connectors in the bracket.
Step 1: Remove the front panel. Remove the retaining
screws from the battery bracket and then remove the cover
itself. undraw the connectors.
Step 4: Tighten the screws of the battery bracket and front
panel .
Step 2: Pull the battery tray out slowly. Put the new battery
tray back into the compartment after that.
Copyright © 2016 CyberPower Systems, Inc.
13
TECHNICAL SPECIFICATIONS
Model
Configuration
Capacity (VA)
Capacity (Watts)
Form Factor
Energy-saving Technology
Input
Input Voltage Range
Input Frequency Range
Input Power Factor
Cold Start
Output
Output Waveform
Output Voltage
Output Frequency
Transfer Time (Typically)
Rated Power Factor
Harmonic Distortion
Crest Factor
ECO Mode Voltage
Regulation
UPS Outlets
Protection
Surge Protection
Phone / Network Protection
Overload Protection
Short Circuit Protection
OLS1000ERT
(XL)2U
OLS1500ERT
(XL)2U
OLS2000ERT
(XL)2U
OLS3000ERT
(XL)2U
1000VA
900W
1500VA
1350W
2000VA
1800W
3000VA
2700W
Rack
Yes, ECO Mode Efficiency ≧95%
110~130Vac 5% for 1000 / 1500 / 2000 VA model
110~140Vac 5% for 3000 VA only
120~140Vac 5% for 1000 / 1500 / 2000 VA model
140~160Vac 5% for 3000 VA only
140~160Vac 5% for 1000 / 1500 / 2000 VA model
160~190Vac 5% for 3000 VA only
160~300Vac 5% for 1000 / 1500 / 2000 VA model
190~300Vac 5% for 3000 VA only
40~70Hz
0.98
Yes
@ 0~50% Load  5%
@ 0~60% Load 5%
@ 0~80% Load 5%
@ 0~100% Load 5%
Pure Sine Wave
208, 220, 230, 240Vac ±1%
50 / 60Hz (Auto-Sensing or Configurable) ±0. 5Hz
0ms
0.9
THD < 3% at Linear Load, < 5% at Non-linear Load @ Nominal Input
3:1
±10%, ±15% (Configurable)
(3+3) IEC C13
(4+4) IEC C13
(4+4) IEC C13
(1) IEC C19
IEC 61000-4-5 Level 4
RJ11/RJ45 (One In/One Out)
Line Mode: 105~110%
Overload warning only (No shutdown),
110~120% Warning, transfer to bypass after 60s
>120%
Transfer to bypass immediately
Battery Mode: 105~110% Overload warning only (No shutdown),
110~120% Warning, shutdown after 10s
>120%
Shutdown immediately
Bypass Mode :Warning only @ 130%>Load>105%, Shutdown immediately @
Load>130%
UPS Output Cut off Immediately or Input Fuse / Circuit Breaker Protection
Battery
Specifications
Recharge Time (Typically)
Sealed, Maintenance Free
Status Indicators
LCD Screen
Audible Alarms
(3) 12V/7AH
(3) 12V/9AH
(6) 12V/7AH
For XL Models, NO Battery Inside.
4 Hours (inside batteries)
Yes
(6) 12V/9AH
Graphic LCD
Battery Mode, Battery Low, Overload, UPS Fault, Replace Battery, Bypass Mode
Charger Failure /Over Charged, Fan failure, EPO active
Environment
Operating Temperature
Operating Relative Humidity
32℉ to 104℉ ( 0℃ to 40℃)
20 to 90% Non-Condensing
Copyright © 2016 CyberPower Systems, Inc.
14
TECHNICAL SPECIFICATIONS
Management
On-Device Features
Connectivity Ports
SNMP/HTTP Capable
Software
Power Management
Software
Physical
Dimensions (H x W x D)
Net Weight
Self Test, Auto-Charge, Auto-Restart, Auto-Overload Recovery
(1) Serial Port (RS232), (1) USB Port,
(1) Expansion Port (With optional RMCARD 205)
®
PowerPanel Business Edition
3.46x 17.24x15.75 in.
88×438×400 mm
384.2(18.6)lbs
32.2(18.8)lbs
13.2(8.4)Kg
14.6(8.5)Kg
Safety
Conformance Approvals
3.46x 17.24x22.83 in.
88×438×580 mm
46.8(25.6)lbs
60.9(26.5)lbs
21.2(11.6)Kg
27.6(12)Kg
CE
*) Within 50/60Hz±8% by default, the output frequency is synchronization with input mains. User can adjust the
acceptable range for output frequency (±1, 2, 3, 4, 5, 6, 7, 8, 9, 10%). When input frequency is out of synchronization
window but within 40-70Hz, UPS can stay in line mode and output frequency is regulated at 50/60Hz+0.5% with load
derating by 40%.
Copyright © 2016 CyberPower Systems, Inc.
15
TROUBLE SHOOTING
Problem
Possible Cause
Solution
Warning
Your equipment requires more power than the
Shut off non-essential equipment. If this solves
UPS can provide. If the UPS is in Line Mode
O/P Overload
the overload problem, the UPS will transfer to
then it will transfer to Bypass Mode; if the UPS is
normal operation.
in Battery Mode it will shutdown.
Save your data and perform a controlled-
Battery Mode
UPS is operating on battery power.
shutdown.
UPS is operating on battery power and will be
UPS will restart automatically when acceptable
Battery Low
shutting down soon due to extremely low battery
utility power returns.
voltage.
Check battery connector when use battery
BAT Disconnected/
Missing battery power.
packages.
Battery Replace
UPS has failed in Battery Test.
Contact technical support to replace the battery.
1. Shut down UPS and turn off AC input.
Charger Failure
Charger has failed.
2. Contact CyberPower for repair.
EPO OFF
Missing the EPO connection.
Check the EPO connection.
Fault
1. Shut down UPS. Restart UPS to Check the
fan for operation and if the ventilation hole has
Over Temperature
High ambient temperature.
been covered
2. Contact CyberPower for repair.
1. Shut down UPS
Output Short
Output short circuit.
2. Your attached equipment may have problems,
please remove them and check again.
High O/P V
Output voltage is too high.
Low O/P V
Output voltage is too low.
Bus Fault
Internal DC bus voltage is too high or too low.
1. Shut down UPS
2. Contact CyberPower for repair.
Other
1. Restart UPS and press the
“▼” button to
High temperature, or fan fail, or battery low, or
view the warning event. Then refer to the solution
EPO off..
for the warning.
Startup fail
2. Contact CyberPower for repair.
Copyright © 2016 CyberPower Systems, Inc.
16
TROUBLE SHOOTING
CyberPower Systems Inc.
www.cyberpower.com
©
Entire contents copyright 2016 CyberPower Systems Inc., All rights reserved. Reproduction in whole or in part without
permission is prohibited. PowerPanel
®
Business Edition and PowerPanel
®
Personal Edition are trademarks of
CyberPower Systems Inc.
Copyright © 2016 CyberPower Systems, Inc.
17