IntrigueDirect Vent Gas Fireplace

Intrigue
Direct Vent Gas Fireplace
MODEL: UF0100
English and French Installation Manuals available through your local dealer or visit our website at:
www.archgard.com
Les manuels d'installation en anglais et en français son disponibles chez votre détaillant local ou en visitant notre site web:
www.archgard.com
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile home
where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result, causing property damage, personal injury or loss of life.
WHAT TO DO IF YOU SMELL GAS:
•
•
•
•
•
Do not light any appliance
Do not touch any electrical switch: do not use any phone in your building.
Immediately call your gas supplier from a neighbors phone.
Follow the gas suppliers instructions.
If you can not reach your gas supplier, call the fire department.
Do not store or use gasoline or other flammable
vapors or liquids in the vicinity of this or any other
appliance.
Installation and service must be performed by a qualified installer, service agency or the gas supplier
ARCHGARD FIREPLACE PRODUCTS
7116 Beatty Drive
Mission, BC V2V 6B4
Canada
200-U100-02
January 5 2017
TABLE OF CONTENTS
RATING PLATE LABEL
3 FINALIZING THE INSTALLATION31
SAFETY INFORMATON
4 CONTROL SYSTEM COMPONENTS
33
SPECIFICATIONS
6 SYSTEM OPERATION
34
FIREPLACE DIMENSIONS
6
Intializing the System 34
UF0100 COMPONENTS LIST
7
Temperature Display
34
INSTALLATION OVERVIEW
7
Turn on the Appliance
34
PREPARE THE FIREPLACE
Turn off the Appliance
8
34
Stand-off Assembly & Installation 8
Manually Control Flame
34
Horizontal Vent Heat Shield Installation
9
Room Thermostat 35
Nailing Flange Assembly & Installation
9
Smart Thermostat 35
FRAMING
10
Fan Speed Control
35
Wall Encloser Rough Opening
Accent Light Kit 10
35
Min. Finished Opening Dimensions 10
Key Lock
35
Optional Full Door Face Dimensions
11
Low Battery Detection
36
Framing
11
Continuous Pilot / Intermittent Pilot 36
Horizontal Terminations
Reset System for Manual Operation
12
36
Vertical Terminations
12
Automatic Safety Restart
36
TYPICAL INSTALLATION OPTIONS 13
S.I.T. Proflame 2 IFC Ignition and Reset
Typical Horizontal Installation
13
37
Typical Corner Installation
13 LIGHTING AND SHUTDOWN
38
Typical Vertical Installation
13 MAINTENANCE
40
MANTEL REQUIREMENTS
14
Control Board System
40
Non-Combustible Zone:
Fan
14
40
GRILL SET
15
Vent System
40
Glass Door Removal and Installation 16
Glass Cleaning & Replacement
40
Remove Glass Frame Assembly 16
Reflective Panel Kit Removal
41
Install Glass Frame Assembly
16
Refractory Panel Kit Removal
43
UF0100 SAFETY BARRIER
BURNER REMOVAL
17
45
GAS LINE CONNECTION
18
BURNER INSTALLATION
46
Gas Conversion
18
Troubleshooting
47
LIGHT KIT INSTALLATION
18 CONVERSION KIT INSTRUCTIONS 48
VENTING
19 REPLACEMENT PARTS LIST 51
Approved Venting
19 LIMITED WARRANTY
52
Horizontal Terminations
19 LIFETIME WARRANTY
53
Horizontal Terminations
20
Vertical Terminations
20
Termination Vent Cap Location
22
Location Clearances
22
Vent Termination Clearances
23
REFRACTORY PANEL KIT 24
REFLECTIVE GLASS PANEL KIT26
LOG SET INSTALLATION
28
WIRING SCHEMATICS
29
PRESSURE TESTING
30
2
RATING PLATE LABEL
E
L
P
M
A
S
3
General Information
SAFETY INFORMATON
This fireplace has been listed by LABTEST Certification Inc to the following USA and Canada gas appliance standards:
ANSI Z21.88-2014/CSA 2.33-2014 “Standard for Vented Gas Fireplace Heaters.”
CAN 2.17-M19 (R2009), “Gas-Fired for Use at High Altitudes.”
CAN/CSA P.4.1-09, “Testing Method for measuring Annual Efficiency Installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or
the Natural Gas and Propane Installation Code, CSA B149.1.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
Installation and repair should be done only by a qualified service person. The appliance should be inspected by a qualified service
person before use. Annual inspection by a qualified service person is required to maintain warranty. More frequent cleaning may
be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners, and
circulation air passageways of the appliance be kept clean
If this appliance is installed directly on carpeting, tile, or other combustible material other than wood flooring, the appliance shall be
installed on a metal or wood panel extending the full width and depth of the appliance
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing
ignition
Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children, and
others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the
house. To restrict access to a fireplace or stove, install an adjustable safety gate to keep toddlers, young children, and other at risk
individuals out of the room and away from hot surfaces
Clothing or other flammable material should not be placed on or near the appliance
Adequate accessibility clearances for servicing and proper orientation must be maintained
This appliance must not share or be connected to a chimney flue servicing any other appliance
Keep are around the appliance clear of combustible materials, gasoline, and other flammable vapor and liquids
The flow of combustion and ventilation air must not be obstructed
Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies
The glass front or any part removed for servicing the appliance must be replaced prior to operating the appliance. Work should be
done by a qualified service technician
Clean glass only when cool and only with non-abrasive cleansers
WARNING: DO NOT OPERATE APPLIANCE WITH THE GLASS/FRAME ASSEMBLY REMOVED, CRACKED OR BROKEN.
REPLACEMENT OF THE GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR QUALIFIED SERVICE PERSON
The glass assembly shall only be replaced as a complete unit, as supplied by Archgard Industries Ltd. DO NOT SUBSTITUTE
ANY MATERIALS
Do not strike or slam glass assembly
Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the appliance
Under no circumstances should any solid fuel (wood, coal, paper or cardboard, etc.) be used in this appliance
Keep burner and control compartment clean
Do not use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect this appliance
and to replace any part of the control system and any gas control which has been under water
General Information
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
NOTE: The following requirements reference various Massachusetts and national codes not contained in this manual.
For all sidewall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less
than (7) feet above finished grade in the are of the venting, including but not limited to decks and porches, the following requirements
shall be satisfied:
INSTALLATION OF CARBON MONOXIDE DETECTORS
At time of installation of side wall horizontally vented gas fueled equipment, the installing plumber or gas-fitter shall observe that a
hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be
installed. In addition, the installing plumber or gas-fitter shall observe that a battery operated or hard wired carbon monoxide detector is
installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment.
It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard
wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a
period of thirty (30) days to comply with the above requirements: provided, however, that during said thirty (30) day period, a battery
operated carbon monoxide detector with an alarm shall be installed.
APPROVED CARBON MONOXIDE DETECTORS
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and ANSI/UL 2034
listed and IAS certified.
SIGNAGE
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum of eight (8) feet above
grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall
read, in print no less than one-half inch (1/2) in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS".
INSPECTION
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon
inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08
(2) (a) 1 through 4.
EXEMPTIONS
The following equipment is exempt from 248 CMR 5.08 (2) (a) 1 through 4: The equipment listed in Chapter 10 entitled "Equipment Not
Required To Be Vented" in the most current edition of NFPA 54 as adopted by the Board; and Product Approved side wall horizontally
vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for
residential purposes.
MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED
When the manufacturer of Product Approved side wall horizontally vented gas equipment does not provide the parts for venting the flue
gases, but identifies "special venting systems", the following requirements shall be satisfied by the manufacturer:
The referenced "special venting systems" instructions shall be included with the appliance or equipment installation instructions
and;
The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list
and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the
completion of the installation.
(G1-0216-394)
5
Installation
FIREPLACE DIMENSIONS
SPECIFICATIONS
DESCRIPTION
Height
Width
Back
Width
Depth
Opening
Width
Glass
Frame
Height
Stand-off
Height
Front
to Vent
Center
(Vert.
Term.)
Floor
to Vent
Center
(Hor.
Term.)
Front to
Angled
Back
FIREPLACE
INCHES
DIMENSIONS
MILLIMETERS
34-1/2
40-7/8
30-7/8
19-3/8
35-1/2
26-5/8
10
16-1/8
33-3/8
8-1/8
876
1038
785
493
902
676
254
410
848
210
WARNING
All stand-off brackets must be attached to fireplace. Do not remove. Top stand-off brackets are not load bearing. Non-combustible
zone: Top stand-offs provide 10" (254 mm) minimum clearance to header. Use only non-combustible material in this area for entire
width of fireplace. Do not use wood, sheetrock, etc. in this zone. Other clearances apply. All clearances must be maintained.
30 7/8"
772mm
8 1/8"
200mm
6
Installation
UF0100 COMPONENTS LIST
DESCRIPTION
IPI Control Board Assembly
Manual Gas Shut-off Valve
Burner Assembly
Refractory Set (back and sides) (optional - purchased separately)
Log Package
Glass Frame Assembly
Double Receptacle Assembly
Grill Assembly
Remote Control
Light Kit
Fan Kit
INSTALLATION OVERVIEW
NOTE
The qualified installer should follow the procedure best suited for
the installation.
NOTE
This appliance must be electronically grounded and connected
in accordance with local codes, or in the absense of local codes,
with the National Electrical Code, ANSI/NFPA 70 Current Edition,
or the Canadian Electrical Code CSA C22.1.
1. Frame an opening for the fireplace, allowing for vent installation (top or rear) and type of installation (corner or flat wall application).
2. If masonry (optional) is used, prepare foundation for the masonry load. A lintel is required to support the added weight above fireplace.
3. Attach nailing flanges to fireplace.
4. Insert fireplace into framing.
5. Install hearth (if applicable).
6. Complete electrical hook-up. Install any standard or optional electrical components.
7. Complete gas line installation.
8. Complete venting installation.
9. Secure fireplace to flooring through holes in outer box bottom and to framing with nailing flanges. Verify all clearances.
10. Install facing material (non-combustible to 10" above the fireplace), mantel or cabinetry, allowing room for optional full face doors, if
applicable.
11. Install the panel set.
12. Install logs.
13. Install grills and optional decorative doors / faces.
14. Verify proper operation of fireplace and all components.
PLACEMENT CLEARANCE REQUIREMENTS
• This fireplace must be installed on a level surface capable of supporting the fireplace and venting
• Fireplace must be placed directly on wood or non-combustible surface (not linoleum or carpet) extending entire depth and width of
fireplace
• Facing material must be all non-combustible to 10" above the fireplace
• Due to high surface temperatures, fireplace should be located out of traffic and away from furniture and draperies
• This fireplace may be installed in a bedroom
• Please be aware of the large amount of heat this fireplace will produce when determining a location
7
Installation
PREPARE THE FIREPLACE
Stand-off Assembly & Installation
WARNING
Top stand-off brackets and stand-off heat shields must be attached to fireplace. Do not remove. These items are not load bearing.
Non-combustible zone: Stand-offs provide 10" (254 mm) minimum clearance to header. Use only non-combustible material in
this area for entire width of fireplace. Do not use wood, sheetrock etc. in this zone. Other clearances apply. All clearances must
be maintained.
Top stand-off brackets and stand-off shields are attached to fireplace top in a flat state for shipping.
1. Remove and save (4) screws securing stand-off heat shields and stand-off brackets, and (4) screws located under these items.
2. Form stand-off brackets as shown and re-attach to fireplace using screws previously removed.
3. Form stand-off heat shields and attach to stand-off brackets using (8) screws provided in components packet. (Stand-off heat
shield flanges face up and to the front of fireplace).
8
Installation
Horizontal Vent Heat Shield Installation
IMPORTANT
The horizontal vent heat shield must be installed when using a 45-degree elbow to horizontally position the vent system.
EXCEPTION: Corner installations.
1. Loosen, but do not remove center three screws at back of fireplace as shown.
2. Bend horizontal heat shield at perforation to a 45° angle. Slide (3) slots on
horizontal vent heat shield under loosened screws. Re-tighten screws.
Nailing Flange Assembly & Installation
1. Remove (4) nailing flanges from fireplace sides.
2. With the 1/2" (13 mm) stand-offs on nailing flanges facing away from fireplace, align nailing flange with holes on outside corners of
fireplace. Secure with screws through slots in nailing flanges (additional screws provided in components packet).
3. Bend perforation on nailing flange until parallel with fireplace face. Do not bend toward fireplace face.
4. Position framing stud against 1/2" (13 mm) stand-off (located on backside of nailing flange). Secure with nails or screws.
NOTE
Depending on facing material, tabs can be adjusted forward or
backwards up to 1/2" (13 mm).
CAUTION
Never permanently remove these assemblies from fireplace they must be secured in place regardless of finish material used.
When installed, nailing flanges provide minimum 1/2" (13 mm) clearance from fireplace sides.
9
Installation
FRAMING
Wall Encloser Rough Opening
IMPORTANT
Framing dimensions should allow for wall covering thickness and fireplace facing materials. If using a hearth, adjust rough opening
size as necessary to maintain at least minimum clearance requirements.
Non –combustible facing material may be applied over (but not directly to) fireplace face. This will prevent facing material from
falling off due to heat expansion. Do not obstruct the flow of ventilation air.
Min. Finished Opening Dimensions
HORIZONTAL TERMINATION: 44-1/2” (1130mm) HIGH x 41-7/8” (1051mm) WIDE x 22” (546mm) DEEP.
1/2” (13mm) clearance back and sides of fireplace must be maintained.
VERTICAL TERMINATION: 44-1/2” (1130mm) HIGH x 41-7/8” (1051mm) WIDE x 22” (546mm) DEEP.
1/2” (13mm) clearance back and sides of fireplace must be maintained.
Note: Framing dimensions assume the use of 1/2" drywall.
NOTE
WARNING
Provide adequate clearance in front of fireplace to operate
lower grill, open and close optional full door face doors, access
Components, installation of gas line, fan, etc. See figure 8b.
Provide adequate clearances around air openings into the
combustion chamber.
Do not obstruct upper and lower grill openings. Room air enters
through lower passage, is heated and exists through upper
passage. Blocking these passages may result in overheating,
creating a potentially hazardous situation.
22" (546mm)
10
Installation
Optional Full Door Face Dimensions
If installing an optional full door face, please refer to below for full
face dimensions before applying facing material.
NOTE
Consider height of hearth finish material (stone, brick, marble
etc.) when building fireplace platform. Bottom of fireplace must
be level with finished hearth to allow for lower grill operation and
proper fit of optional decorative full door faces.
1/2” (13mm) side overlap applies to both sides of face. Illustrations show True Dimensions. We recommend 1/4” (6mm) clearance on all sides to allow for uneven finish material.
Framing
Determine exact position of your fireplace, including hearth height, width, and depth (if applicable). If possible, place fireplace in such a
manner that vent termination will be between two studs, eliminating the need for additional framing.
If masonry is to be used (optional), prepare the necessary foundation for the masonry load. When masonry construction is used, a
lintel must be used over top of fireplace to support the added weight.
Build hearth to desired size and height. If a hearth extension is desired, combustible material may be used.
NOTE
WARNING
FIRE
HAZARD
IMPORTANT
WARNING
Consider height of hearth finish material (stone, brick etc.) when building fireplace platform. Bottom of fireplace
must be level with finished hearth to allow for lower grill operation and proper fit of optional decorative full door
faces.
Install fireplace on hard metal or wood surface extending the full width and depth of fireplace.
Minimum platform size: 41-7/8” (1064mm) x 19-3/8” (493mm) deep.
DO NOT install directly on carpet, vinyl, or any combustible material other than wood.
Vent cap location must be in compliance with guidelines on page 22 of this manual.
DO NOT RECESS VENT CAP INTO WALL OR SIDING.
11
Installation
Horizontal Terminations
Follow vent pipe manufacturer’s installation instructions for horizontal terminations.
Include required vent manufacturer’s wall pass-thru clearances when determining
framing dimensions.
MINIMUM HORIZONTAL FRAMING DIMENSIONS
VENT PIPE CENTER (A)
RIGID PIPE
FLEX PIPE
FRAMED OPENING TOP (B)
33-3/8" (848 mm)
Per vent manufacturer's
requirements
36-7/8" (973 mm)
Per vent manufacturer's
requirements
W
H
B
A
HEARTH
HEIGHT
Vertical Terminations
Follow vent pipe manufacturer’s installation instructions for vertical terminations.
A minimum of 1” (25mm) clearance on all sides of vertical vent pipe must be
maintained.
NOTE
12
The included Horizontal Vent Heat Shield is not used for vertical configurations.
CAUTION
Cold air transfer area. The surrounding fireplace chase must comply with all clearances as outlined in this manual and be constructed in compliance with local building codes. Outside walls should be insulated to prevent
cold air from entering.
CAUTION
Due to high temperatures, this fireplace should be located out of traffic areas and away from furniture and draperies.
Installation
TYPICAL INSTALLATION OPTIONS
IMPORTANT
The horizontal heat shield included with this fireplace must be installed when incorporating minimum horizontal venting. This applies
to Nat. and LP minimum horizontal venting configurations.
Horizontal vent heat shield not shown in illustrations below for clarity purposes only.
Typical Horizontal Installation
Typical Corner Installation
Typical Vertical Installation
13
Installation
MANTEL REQUIREMENTS
WARNING
TOP STAND-OFF BRACKETS MUST BE ASSEMBLED AND ATTACHED TO FIREPLACE. DO NOT REMOVE.
STAND-OFF BRACKETS ARE NOT LOAD BEARING
Non-Combustible Zone:
Rigid Pipe: 1: (25 mm) above elbow for entire width and depth (behind header) of fireplace.
Flexible Venting: 1" (25 mm) above elbow for entire width and depth (behind header) of fireplace.
14
Installation
GRILL SET
Installation
1. Align hooks in upper louver to slots located in fireplace
face. Set down into position.
2. Insert upper hood flange into clips located at top of
upper air passage, keeping in mind this is a fairly tight
fit.
3. Partially thread (2) screws (included in components
packet) into nuts at each end of lower grill. Secure to
fireplace by threading screws into corresponding holes
in inside flange of lower grill opening. The lower grill can
now be opened and closed to access gas valve and
controls.
Removal
1. Use both hands to pull hood out of upper air passage
clips.
2. Lift upper louver up and out of slots.
3. Remove screws securing lower grill at each end to
remove from fireplace.
15
Installation
Glass Door Removal and Installation
Remove Glass Frame Assembly
1.
2.
3.
4.
Locate spring-loaded handles securing glass frame assembly at top & bottom of firebox.
Pull bottom handles out and down to release glass frame assembly bottom. Hold glass frame in place when releasing handles.
Pull top handles out and up to release glass frame assembly top.
Remove glass frame assembly from fireplace.
FIREPLACE BOTTOM
FIREPLACE TOP
PULL OUT AND DOWN TO RELEASE
PULL OUT AND UP TO RELEASE
Install Glass Frame Assembly
Installation is the reverse of removal.
1. Pull top handles out and down to secure glass frame assembly top.
2. Pull bottom handles out and up to secure glass frame assembly bottom.
16
Installation
UF0100 SAFETY BARRIER
•
•
•
•
REMOVE TOP LOUVER AND HOOD
OPEN BOTTOM LOUVERS
UNDO TOP & BOTTOM DOOR LATCHES
REMOVE SCREEN
TO REINSTALL THE BARRIER SCREEN, REVERSE THE STEPS FOR REMOVAL.
NOTE: If the barrier becomes damaged, the barrier shall be replaced with the manufacturer's barrier for this appliance.
WARNING
DOOR MUST BE INSTALLED PRIOR TO SCREEN
INSTALLATION TO AVOID POSSIBLE DAMAGE OR INJURY.
17
Installation
GAS LINE CONNECTION
Gas Conversion
This fireplace is manufactured for use with Natural Gas. Follow instructions included with conversion kit if converting to LP gas (Sold
separately).
CAUTION
Installation of the gas line must only be done by a qualified person in accordance with local building codes, if
any. If not, follow ANSI 223.1.
Commonwealth of Massachusetts: Installation must be done by a licensed plumber or gas fitter.
A listed (and Commonwealth of Massachusetts approved) 1/2" (13mm) T-handle manual shut-off valve and
flexible gas connector (included) are connected to 1/2" (13mm) control valve inlet. If substituting for these
components, please consult local codes for compliance.
This fireplace is equipped with a 3/8" (10mm) x 7" (178mm) long flexible gas connector and manual shut-off
valve. The gas line should be run to the point of connection where the shut-off valve and flexible gas line will
connect.
NOTE
The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during
any pressure testing of that system at pressures in excess of 1/2 psi (3.5 kPa).
The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve
during any pressure testing of the gas line at test pressures equal to or less than 1/2 psi (3.5 kPa).
For high altitude installations, consult the local gas distributor or the authority having jurisdiction for proper rating
methods.
IMPORTANT
The efficiency rating of this appliance is a product of thermal efficiency rating determined under continuous
operating conditions and was determined independently of any installed system.
NATURAL GAS
LP GAS
Minimum Inlet Gas Pressure
5" WC (1.25 kPa)
12" WC (2.99 kPa)
Maximum Inlet Gas Pressure
14" WC (3.5 kPa)
14" WC (3.5 kPa)
Manifold Pressure (HI)
3.8" WC (.95 kPa)
11" WC (2.74 kPa)
Manifold Pressure (LO)
1.1" WC (.27 kPa)
2.9" WC (.72 kPa)
Orifice Size
#56 & #33
#63 & #51
Input BTU/hr (kW)
39,500 (11.58 kW)
39,500 (11.58 kW)
Minimum Input BTU/hr. (kW)
19,500 (5.72 kW)
19,500 (5.72 kW)
Front Burner Air Shutter Setting
Fully Closed
5/8" (16mm) Open
Back Burner Air Shutter Setting
1/8" (3mm) Open
5/8" (16mm) Open
LIGHT KIT INSTALLATION
CAUTION
NOTE
Disconnect all electrical power from fireplace before performing this task.
To avoid damage and prolong the life of halogen bulbs, never touch with bare hands. Always use a soft cloth
when handling.
1. Install halogen bulbs (included in components packet
into lamp bases.
2. Place amber light filters into light cylinders.
18
Installation
VENTING
WARNING
Consult the local and international codes to assure adequate combustion and ventilation air is available.
Flame height and appearance will very depending upon venting configuration and type of fuel used.
Venting requirements apply to both Natural and LP gas.
Refer to the vent manufacturer’s installation manual for complete installation instructions.
Installation must conform with the venting requirements and restrictions as outlined in this manual.
Provide a means for visually checking vent connection to fireplace after fireplace is installed.
Approved Venting
•
•
•
•
•
•
•
Simpson Dura-Vent DV-GS 5” x 8” and 4” x 6-5/8” with reducer (horizontal and vertical terminations).
Metal Fab Direct Chimney Systems 5” x 8” (horizontal and vertical terminations).
ICC Direct Chimney Systems 5” x 8” (horizontal and vertical terminations).
Selkirk-Metalbestos Chimney Systems 5” x 8” and 4” x 6-5/8” with reducer (horizontal and vertical terminations).
BDM 5” x 8” Chimney Systems, flex and rigid (horizontal and vertical terminations).
Security 5” x 8” Chimney Systems (horizontal and vertical terminations).
Ameri-Vent 5” x 8” Chimney Systems (horizontal and vertical terminations).
Horizontal Terminations
HORIZONTAL VENT SYSTEM CLEARANCES
ALL APPROVED VENTING
TOP
BOTTOM
SIDES
2 INCHES (51 mm)
1 INCH (25 mm)
1 INCH (25 mm)
HORIZONTAL MIN. / MAX.
MINIMUM: 45° Horizontal elbow + 6" - 24" pipe (152 mm - 609 mm) + snorkel termination cap (12" Min).
MAXIMUM: 45º Vertical elbow + 1ft. Vertical Pipe (305mm) + 90º elbow + 3 ft. pipe (914mm) + termination cap.
HORIZONTAL MIN. / MAX. (with reducer)
NAT GAS MINIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 6” (152mm)horizontal + termination cap.
NAT GAS MAXIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 4ft. (1.2m) + termination cap.
LP GAS MINIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 6” (152mm) + termination cap.
LP GAS MAXIMUM: 2ft. (610mm) vertical + reducer + 90º elbow + 1ft. (305mm) + termination cap.
LP GAS MAXIMUM: 3ft. (914mm) vertical + reducer + 90º elbow + 4ft. (1.2m) + termination cap.
IMPORTANT
When running on LP, the restrictor must be removed when on 8 x 5 vent with a vertical of 1' or less. The restrictor
must also be removed when running on LP when on 4 x 65/8 vent with a vertical of 3' or less. See restrictor
removal in Gas Conversion section.
IMPORTANT
Wall pass-thru required for all horizontal runs. Refer to vent manufacturer to determine which pass-thru will work
best for your application and wall thickness.
The horizontal vent shield must be installed when using a 45º elbow to horizontally position the vent system.
Exception: corner installations.
ELBOWS
The following statement applies to horizontal, vertical, or a combination of horizontal / vertical elbows:
For each additional 90º elbow used after the first elbow, 3ft. (914mm) must be subtracted from the maximum allowed venting. For
each 45º elbow used, 1-1/2ft. (457mm) must be subtracted from the maximum venting allowed.
NOTE
(2) 45º degree elbows may be used in place of (1) 90º elbow.
19
Installation
NOTE
CAUTION
Horizontal sections require 1/4" (6 mm) rise for every 12" (305 mm) of travel.
This gas appliance must not be connected to or joined with any other chimney flue serving another appliance.
Horizontal Terminations
Vertical Terminations
VERTICAL VENT SYSTEM CLEARANCES
SIDES
ALL APPROVED
VERTICAL VENTING
1 inch (25 mm)
VERTICAL MIN. / MAX.
MINIMUM: 45° elbow + 3ft. (915 mm) + termination cap.
MAXIMUM: 45° elbow + 50ft. (15.2 m) + termination cap.
MAXIMUM (if using reducer):
45° elbow + 2ft. (610 mm) + reducer + 48ft. (14.63m) + termination cap.
RESTRICTOR SETTING
This fireplace is shipped with the restrictor set in open position. Follow chart for recommended settings based on venting
configuration. It is important to remember each installation is unique and affected by various factors including venting configuration,
altitude and climate. Therefore, after fireplace installation is complete, restrictor setting adjustment may be necessary. Page 31 has
information on restrictor recommendations depending on burner flame appearance after installation is completed.
Restrictor setting adjustment handle is located at top front of firebox. Remove glass frame assembly to access. Loosen screw, adjust
setting, tighten screw and reinstall glass frame assembly.
IMPORTANT
When running on LP, the restrictor must be removed when on 8 x 5 vent with a vertical of 1' or less. The restrictor
must also be removed when running on LP when on 4 x 65/8 vent with a vertical of 3' or less. See restrictor
removal in Gas Conversion section.
RECOMMENDED RESTRICTOR SETTINGS
VENTING
RESTRICTOR POSITION
Min. - 20ft. (6.1m)
FULL OPEN
(handle pulled forward)
20ft. (6.1m) - 35ft. (10.7m)
PARTIAL OPEN
(handle set to center)
35ft. (10.7m) - 50ft. (15.2m)
CLOSED
(handle pushed back)
20
Installation
HORIZONTAL & VERTICAL COMBINATION TERMINATIONS
MAXIMUM: 18ft. (5.49m) horizontal + 18ft. (5.49m) vertical + cap. [36ft. (10.98 m) total].
MAXIMUM (with reducer): 45° elbow + 2ft. (610 mm) vert. + reducer + 16ft. (4.88 m) vert. +9ft. (2.74 m) hor. + cap.
IF INSTALLING WITH RIGID-TO-FLEX PIPE SYSTEMS:
ATTENTION
IMPORTANT
More than a 30 degree bend constitutes a 45 degree elbow.
More than a 45 degree bend constitutes a 90 degree elbow.
More than a 90 degree bend is not permissible.
Wall pass-thru required for all horizontal runs. Refer to vent manufacturer to determine which pass-thru will work
best for your application and wall thickness.
The horizontal vent heat shield must be installed when using a 45-degree elbow to horizontally position the vent
system. Exception: corner installations.
HORIZONTAL / VERTICAL COMBINATION:
(5.49m) 18' Vertical
(5.49m) 18' Horizontal
21
Installation
Termination Vent Cap Location
This gas appliance must not be connected to a chimney serving any other appliance.
1. Terminations against vinyl siding must use a vinyl siding protector. Follow instructions included.
2. DO NOT RECESS TERMINATION KIT INTO OUTSIDE BUILDING MATERIALS - i.e.: brick, stone, siding, etc. If necessary, extend
framing so that termination kit will be exposed once building materials are installed.
3. Vent termination must not be located where it will become plugged by snow or other material. The flow of combustion and
ventilation air must not be obstructed.
Location Clearances
A. Above grade, veranda, porch, deck, balcony - 12" (305 mm).
B. Operable window or door - CANADA: 12" (305 mm), US: 9" (229 mm).
C. Permanently closed window* - 12" (305 mm) (recommended to prevent condensation on window).
D. Ventilated soffit* - 24" (610 mm).
E. Unventilated soffit* - 12" (305 mm).
F. Outside corner* - 3" (76 mm).
G. Inside corner* - 10" (254 mm).
H. Meter / Regulator: CANADA: Not to be installed above a gas meter/regulator assembly within 3 ft. (914 mm) horizontally from the
centerline of the regulator within a height of 15ft. (4.57 m). US*.
I. Gas Service regulator vent outlet: CANADA: 3ft. (914 mm). US*.
J. Non-mechanical air supply inlet to building or the combustion air inlet to any other appliance. CANADA: 12" (305 mm). US: 9" (229
mm).
K. Mechanical air supply inlet. CANADA: 6ft. (1.83m) US: 3ft. (914 mm) above if within 10ft. (3.05 m) horizontally. Massachusetts
installations: 10ft. (3.05 m).
L. Above paved sidewalk or paved driveway located on public property - 7ft. (2.13 m). US*
NOTE
A vent cannot be located directly above a sidewalk or paved driveway that is located between two single family dwellings
and serves both dwellings.
M. Under veranda, porch, deck, or balcony (must be fully opened on a minimum of 2 sides) - 12" (305 mm).
N. Between two horizontal terminations - 12" (305 mm).
O. Between two vertical terminations - 12" (305 mm). Terminations may be same height.
P. Above furnace exhaust or inlet - 12" (305 mm).
*Clearance must be in accordance with local installation codes & the requirements of the gas supplier.
Denotes where installation not allowed
22
Installation
Vent Termination Clearances
Roof Pitch
H (Min.) Ft.
H (Min.) m
Flat to 6/12
1.0
0.30
Over 6/12 to 7/12
1.25
0.38
Over 7/12 to 8/12
1.5
0.46
Over 8/12 to 9/12
2.0
0.61
Over 9/12 to 10/12
2.5
0.76
Over 10/12 to 11/12
3.25
0.99
Over 11/12 to 12/12
4.0
1.22
Over 12/12 to 14/12
5.0
1.52
Over14/12 to 16/12
6.0
1.83
Over 16/12 to 18/12
7.0
2.13
Over 18/12 to 20/12
7.5
2.27
Over 20/12 to 21/12
8.0
2.44
CAUTION
This appliance must not be ocnnected to or joined with any chimney flue serving any other appliance.
23
REFRACTORY PANEL KIT
Installation
Installation
1. Remove left and right side outer refractory clips / supports.
2. Loosen top refractory clips / supports and slide towards you and
remove.
3. Install rear brick panel. Make sure the notches in the brick panel
are placed at the bottom
4. Install left side panel.
24
Installation
5. Reinstall the left refractory clip / support.
6. Slide in top brick panel having it rest on top of the side and rear
panel already installed.
7. Slide top refractory clip / support towards the back of the firebox
and tighten screws.
8. Install the right side brick panel and reinstall the right outer
refractory clip / support.
25
Installation
REFLECTIVE GLASS PANEL KIT
Installation
CAUTION
Glass Panels are fragile. Handle with care.
1. Remove barrier screen, door, and burner media. Remove left and right side
panel clips / supports.
WARNING
2. Loosen top panel clips / supports and
slide outward.
4. Place heat insulation board behind
burner media tray.
5. Place upper spacer on left or right
panel. Bend tabs to secure to the top
of the panel.
7. While holding the rear panel, seat the
left or right panel in the lower glass
spacer.
8. Install left or right panel clip / support to
secure side and rear panels.
Upper side panel
clip / spacer
26
Allow fireplace to cool before installing or
removing panels.
3. Place lower glass spacers on edge of
burner media tray against fire box wall
(repeat for other side).
6. Install rear panel behind burner media
tray.
Upper side panel
clip / spacer
Part# 754-0081
Lower side panel
clip / spacer
Part# 754-0080
Installation
9. Slide top glass panel to rest on the rear
panel and left or right panel.
10. Continue holding the upper panel in
place. Slide the upper clips / supports
toward the back of the firebox and
secure.
11. Install the opposite side panel with
upper clip / spacer. Ensure the top
panel rests evenly on both side
panels.
Upper side panel
clip / spacer
12. Install remaining side panel retainer.
INSTALL COMPLETE
Replacement Panels
Right Side: 311-654-RT rev. F
Left Side: 311-654-LT rev. D
Top: 311-654-RR rev. C
Back: 311-654-BR rev. C
27
Installation
LOG SET INSTALLATION
ATTENTION
NOTE
CAUTION
If converting to LP (propane) gas do so before installing log set. Follow instructions included with the conversion
kit (sold separately).
Log numbers are located on the bottom of each log. Refer to following instructions and illustrations for proper
placement.
Do not place logs directly over burner port holes. Improper log placement may affect flame appearance and
cause excessive soot to build up on logs and glass.
Align holes in bottom of logs #1, #2 & #3 with mounting pins on burner cover, setting down into position. Position #4 logs (2) as shown
above. Do not allow logs to block burner ports.
Install #5 - #10 logs as shown above, aligning with the notches in
base logs, and in the case of log #7, aligning with the notch in log
with burner grate.
Install #11 - #12 logs as shown, aligning with notches in lower logs.
Black Embers should be placed in open areas. Do not block burner
ports.
28
Installation
WIRING SCHEMATICS
THIS SYSTEM REQUIRES ELECTRICITY (120V) AND / OR BATTERIES TO OPERATE.
WARNING
USING BATTERY BACK-UP WILL OPERATE BURNER ONLY. FAN AND LIGHT COMPONENTS WILL
NOT FUNCTION ON BATTERY BACK-UP POWER.
29
Installation
PRESSURE TESTING
IMPORTANT
Pressure check taps for manifold (outgoing) and inlet (incoming) pressure have been incorporated into the valve.
The pressure tap marked OUT measures outgoing pressure and the pressure tap marked IN measures incoming
pressure. Follow instructions below for proper testing procedures. Refer to page 18 for proper NAT and LP manifold
pressures.
NOTE
The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in excess of 1/2 psi (3.5 kPa). The appliance must be isolated
from the gas supply piping system by closing its equipment shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).
Inlet Pressure Test:
1.
2.
3.
4.
5.
6.
Loosen inlet (IN) pressure tap screw (counter-clockwise).
Attach manometer using a 1/4" I.D. hose.
Light pilot and burner. Check pressure to ensure it is between the min. and max. recommended pressure settings.
Turn off burner and pilot.
Disconnect hose and tighten screw (clockwise). Screw should be snug, do not over-tighten.
Relight pilot and burner. Reattach manometer to inlet pressure tap to verify that it is completely sealed. Manometer should read no
pressure.
NOTE
CAUTION
If inlet pressure reading is too high or too low, contact the gas company. Only a qualified gas service technician
should adjust incoming gas pressure.
A LOW PRESSURE READING CAN CAUSE DELAYED IGNITION.
Manifold Pressure Test:
1.
2.
3.
4.
5.
6.
7.
30
Light pilot.
Loosen manifold (OUT) pressure tap screw (counter-clockwise).
Attach manometer to pressure tap using a 1/4" I.D. hose.
Light pilot and burner. Check manometer reading.
Turn burner and pilot off.
Disconnect manometer hose and tighten screw (clockwise). Screw should be snug, do not over-tighten.
Attach manometer to mainfold pressure tap to verify it is completely sealed. Manometer should read no pressure when pilot and
burner are on.
Installation
FINALIZING THE INSTALLATION
Flame Appearance
Flame appearance is affected by several factors including altitude, venting configuration and fuel quality. Although the venturi setting
has been factory set, adjustments may be necessary for optimal performance and visual aesthetics.
When fireplace is first lit, the flames will be blue. Flames will gradually turn yellowish-orange during first 15 minutes of operation. If
flames remain blue, or become dark orange with evidence of sooting (black tips), the burner tube venturi may need adjustment.
Correct Pilot Flame
WARNING
Burner tube adjustable venturi positioning should only be performed by a qualified professional service technician.
FACTORY SET BURNER TUBE AIR SHUTTER SETTINGS (ADJUST AS NECESSARY FOR YOUR INSTALLATION)
FRONT BURNER
BACK BURNER
NATURAL GAS
LP (PROPANE) GAS
100% CLOSED
5/8" (16mm) OPEN
1/8" (3mm) OPEN
5/8" (16mm) OPEN
BURNER TUBE AIR SHUTTER ADJUSTMENT GUIDELINES
VENTURI POSITION
FLAME COLOR
VENTURI ADJUSTMENT
Closed too far
Dark orange flame with black tips
Open air shutter setting slightly
Open too far
Blue flames
Close air shutter setting slightly
NOTE
IMPORTANT
NOTE
If soot is present, check burner media positioning before adjusting burner venturi. Burner media must not block
burner ports.
SLIGHT ADJUSTMENTS TO BURNER AIR SHUTTER OPENING CREATES DRAMATIC RESULTS. ADJUST AT
SLIGHT INCREMENTS UNTIL DESIRED LOOK IS ACHIEVED. ALWAYS BURN FIREPLACE FOR AT LEAST 15
MINUTES AND ALLOW TIME TO COOL BEFORE MAKING ANY FURTHER ADJUSTMENTS.
Front burner venturi generally does not require adjustment unless installing a gas conversion kit.
31
Installation
TO ADJUST BACK (MAIN) BURNER VENTURI:
WARNING
To avoid property damage or personal injury, allow fireplace time to cool before making any adjustments.
Back (main) burner venturi adjustment handle is attached to underside of control board. Access through lower grill opening. Loosen
wing nuts, adjust as necessary, pulling handle forward to open, pushing backwards to close. Tighten wing nuts.
RESTRICTOR ADJUSTMENT:
WARNING
TO AVOID PROPERTY DAMAGE OR PERSONAL INJURY, ALLOW FIREPLACE AMPLE TIME TO COOL BEFORE MAKING ANY ADJUSTMENTS.
Restrictor setting adjustment handle is located at top front of firebox. Remove glass frame assembly to access. Loosen screw, adjust
setting, tighten screw and reinstall glass frame assembly.
RECOMMENDED RESTRICTOR SETTINGS
VENTING
RESTRICTOR POSITION
Min. - 20ft. (6.1m)
FULL OPEN
(handle pulled forward)
20ft. (6.1m) - 35ft. (10.7m)
PARTIAL OPEN
(handle set to center)
35ft. (10.7m) - 50ft. (15.2m)
CLOSED
(handle pushed back)
32
Operation
CONTROL SYSTEM COMPONENTS
REMOTE CONTROL
GAS VALVE
PILOT ASSEMBLY
33
Operation
SYSTEM OPERATION
Intializing the System
for the First Time
1. Set ON/OFF rocker switch to OFF position.
2. Install 4 AA batteries (included in components packet into battery
backup holder.
3. Connect IFC Control Module to AC power supply
4. Install 3 AAA batteries (included in components packet) into remote
control battery bay (located on base of remote control)
NOTE: Performing the next step will initiate Pilot Start-up in Manual
Mode:
• Pilot igniter will spark repeatedly.
• Pilot will ignite if gas is supplied to the fireplace.
Remove all packaging / combustible material from fireplace before
proceeding.
5. Press red SW1 button on IFC control module until module beeps three (3) times and an amber LED is illuminated indicating the
IFC control module is ready to synchronize with the remote control.
6. Within ten (10) seconds push remote control ON/OFF button. The IFC control module will beep four (4) times to indicate the remote
control's command is accepted and set to the particular code of that remote control. Press remote control ON/OFF button again.
The pilot will shut down indicating the remote has taken over. The system is now initialized.
7. Setting ON/OFF rocker switch to ON position will allow you to operate fireplace with remote control.
Temperature Display
With the system in OFF position, press Thermostat Key and Mode
Key at the same time to change from degrees F to C. Look at remote
control LCD screen to verify that C or F is visible on right side of Room
Temperature display.
Turn on the Appliance
Press ON/OFF key on remote control. The display will show all active
icons on the screen. A single 'beep' from IFC Control Module will Confirm reception of the command.
Turn off the Appliance
Press ON/OFF key on remote control. The display will show only room temperature and icon on the screen. A single 'beep' from IFC
control module will confirm reception of the command.
Manually Control Flame
with Remote Control
The remote control has six (6) flame levels. With system ON and flame level at maximum, press Down Arrow Key once to reduce flame
height by one step until flame is turned off. The Up Arrow Key will increase flame height one step each time it is pressed. If Up Arrow
Key is pressed while system is on but flame is off, the flame will come on in High position. A single 'beep' will confirm reception of the
command. When SMART Thermostat is activated, manual flame height adjustment is disabled.
34
Operation
Room Thermostat
(Remote Control Operation)
The remote control can operate as a room thermostat. The thermostat can be
set to desired temperature to control a room's comfort level.
To activate this function, press the Thermostat Key. The LCD display will
change to show the room thermostat is ON and set temperature is now
displayed. To adjust set temperature, press Up or Down arrow keys until
desired set temperature is displayed on the LCD screen.
Smart Thermostat
(Remote Control Operation)
The Smart Thermostat function adjusts flame height based on set temperature
and actual room temperature. As room temperature gets closer to set point
the Smart Function will automatically adjust flame down.
1. Press Thermostat key until word SMART appears on right side of
temperature bulb graphic
2. To adjust set temperature, press Up/Down arrow keys until desired set
temperature is displayed on LCD screen.
When SMART Thermostat is activated, manual flame height adjustment is
disabled.
Fan Speed Control
Fan speed can be adjusted through six (6) speeds. To activate this function
use Mode Key to index to fan control icon. Use Up/Down Arrow Keys to
turn on, off or adjust fan speed. A single 'beep' will confirm reception of the
command.
In Thermostat Mode: Fan(s) have a five (5) minute delay time when fireplace
is lit, allowing time for heat to build in fireplace before operating, and will
continue operating for approximately twelve (12) minutes after fireplace has
been turned off.
In Manual Mode: Fan(s) will operate at previous setting. There is no delay in
start up or stop time.
Accent Light Kit
(not available in all fireplace models)
1. Use MODE key to guide you to LIGHT icon.
2. The light intensity can be adjusted through six (6) levels. Use UP/DOWN
Arrow Keys to adjust intensity level. A single beep will confirm reception
of the command.
Key Lock
This function locks the keys to avoid unsupervised operation.
To Activate: Press MODE and UP keys at same time.
To De-activate: Press MODE and UP deys at same time.
35
Operation
Low Battery Detection
REMOTE CONTROL: Remote control battery lifespan depends on various
factors including battery quality, number of ignitions, changes to room
thermostat set point, etc. When remote control batteries are low a Battery
Icon will appear on the LCD display before all battery power is lost. When
batteries are replaced this icon will disappear.
BACKUP BATTERY PACK (used when electrical power is interrupted):
Backup battery lifespan depends on various factors including battery quality,
number of ignitions, changes to room thermostat set point, etc. When backup
batteries are low, a double-beep will emit from the IFC control module when
it receives an ON/OFF command from the remote control. This is an alert
for a low battery condition of the backup batteries. After this double-beep
warning no commands will be accepted until batteries are replaced. When
batteries are replaced a beep will emit from the IFC control module when it is
powered/
Continuous Pilot / Intermittent Pilot
(CPI/IPI)
This system has the option of a continuous (standing) pilot feature. This
allows you ot change from a spark-to-pilot system to a standing pilot system
during cold weather conditions. By having the pilot on continuously, the
firebox will remain warm and a draft is established in the vent, allowing the
main burner to turn on with less air-flow disruption.
With system OFF position, press Mode Key to index to CPI mode icon.
Pressing the UP Arrow Key will activate the Continuous Pilot Ignition Mode
(CPI). Pressing Down Arrow Key will return to IPI. A single beep will confirm
the reception of the command.
A snowflake icon will be visible during setup of either IPI or CPI modes.
In IPI mode the snowflake is not visible on LCD screen.
In CPI mode the snowflake will remain visible on LCD screen.
Reset System for Manual Operation
1. Put ON/OFF switch in OFF position.
2. Press red SW1 button on IFC control module until the IFC control
module emits three (3) beeps and an amber LED is illuminated,
indicating the IFC control module is ready to synchronize with remote
control. Within ten (10) seconds press the red SW1 button on IFC
control module again. The pilot will automatically light.
3. Turn main burner on by pressing ON/OFF switch to ON position, turn off
by pressing ON/OFF switch to OFF position. Pilot will remain lit even if
burner is turned off.
When operating fireplace in this capacity, the only function available for
burner operation is on HI.
Automatic Safety Restart
This system will execute an automatic turn OFF command within 24 hours of a continued pilot flame ignition. This allows the system to
verify correct safety functions. After turn OFF sequence is completed, the IFC control module will re-execute the latest command.
36
Operation
S.I.T. Proflame 2 IFC Ignition and Reset
Ignition Sequence
Starting from OFF, press remote control ON button. Approximately four (4) seconds after ON/OFF button is pushed, the IFC control
module will start the spark. First ignition try will last approximately sixty (60) seconds.
If there is no flame ignition (rectification) during the first try for ignition, the IFC control module will stop sparking for approximately thirty
five (35) seconds. After this wait time, the IFC control module will start the second try for ignition by sparking for approximately sixty (60)
seconds. If ignition is successful on third ignition attempt, there will be a sixty (60) second delay before the main burner lights.
If after this third attempt there is still no positive ignition, the IFC control module will go into LOCK OUT and the red LED will blink three
(3) times in intervals until the system is reset.
LED Indicator Location: Corder of IFC control module. (IFC control module location determined by fireplace model and design. May
be located in component housing behind lower grill or behind left side access panel).
LOCK OUT = LED blinks three (3) time in intervals until the system is reset.
In Summary:
1. The IFC control module will try two (2) times for ignition.
2. Each try for ignition will last approximately sixty (60) seconds.
3. The wait time between the two tries is approximately thirty five (35) seconds.
RESET IFC CONTROL MODULE WHEN SYSTEM GOES INTO LOCK OUT
Reset Using ON/OFF Switch:
Set ON/OFF switch to OFF position. Wait approximately two (2) seconds and move switch to the ON position. The ignition sequence
will start again.
Reset Using Remote Control ON/OFF Button:
Turn the system off by pressing the remote control ON/OFF button. After approximately two (2) seconds press the remote control ON/
OFF button again. The IFC control module will reset and the ignition sequence will start again.
Reset By Cycling Flame:
In the Manual Flame Control Mode, use the Down Arrow Button to reduce flame to off (indicated by OFF displayed on Remote Control
Display Screen). Wait approximately two (2) seconds and press the Up Arrow Button, the ignition sequence will start.
Additional Diagnostic Indication Information
Low Battery Condition (<4V) Remote Control: Battery Icon will appear on LCD remote control display. Replace batteries.
Low Battery Condition (<4V) Battery Backup: Red LED Indicator will blink one (1) time in intervals. Low double-beep emitted from
IFC control module when it receives an ON/OFF command from the remote control. Replace batteries.
Pilot Flame Error Condition: Red LED Indicator will blink two (2) times in intervals. Contact your dealer.
System Lock Out Condition: Red LED Indicator will blink three (3) times in intervals. Make sure gas is turned on. Make sure sensor is
not shorted. follow Reset IFC Control Module When System Goes Into Lock Out instructions above.
37
Operation
LIGHTING AND SHUTDOWN
FOR YOUR SAFETY - READ BEFORE OPERATING
WARNING
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
1. This appliance is equipped with an ignition device which automatically lights the pilot. DO NOT try to light the pilot by hand.
2. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance
• Do not touch any electrical switch; do not use any phone in your building
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions
• If you cannot reach your gas supplier, call the fire department
3. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control which has been under water.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES
AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN THEY ARE IN THE SAME ROOM AS THE APPLIANCE.
WARNING
CLOTHING OR OTHER FLAMMABLE MATERIAL MUST NOT BE PLACED ON OR NEAR THE APPLIANCE.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
A PAINT SMELL WILL OCCUR DURING THE FIRST FEW HOURS OF BURNING. IT IS RECOMMENDED TO
LEAVE THE FAN OFF DURING THIS PERIOD TO HELP SPEED THE PAINT CURING PROCESS.
NOTE
THIS FIREPLACE MAY PRODUCE NOISES OF VARYING DEGREE AS IT HEATS AND COOLS DUE TO METAL EXPANSION AND CONTRACTION. THIS IS NORMAL AND DOES NOT AFFECT THE PERFORMANCE OR
LONGEVITY OF THE FIREPLACE.
DUE TO HIGH SURFACE TEMPERATURES, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
This appliance needs fresh air for safe operation and must be installed so there are provisions for
adequate combustion and ventilation air.
38
Operation
Operating Instructions
STOP!
Read safety information on the previous
page and front cover of this manual before
continuing.
1. Turn off all electric power to the appliance.
ATTENTION
This appliance is equipped with an ignition
device which automatically lights the pilot. DO
NOT try to light the pilot by hand.
2. Press remote controll OFF button.
3. Wait five (5) minutes to clear out any gas. Smell for gas,
including near the floor. If you smell gas, STOP! Follow 'WHAT
TO DO IF YOU SMELL GAS' below. If you do not smell gas,
proceed to the next step.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance
• Do not touch any electrical switch; do not use any phone in
your building
• Immediately call your gas supplier from a neighbor's phone.
Follow the gas supplier's instructions
• If you cannot reach your gas supplier, call the fire department
4. Turn ON all electric power to the appliance.
5. Press remote control ON button.
CAUTION
If fireplace will not operate, follow instructions
TO TURN GAS OFF TO APPLIANCE and call
your service technician or the gas supplier.
NOTE
When fireplace is initially lit, condensation
will appear on the glass; this is normal in all
gas fireplaces and will disappear after several
minutes.
To Turn Gas Off to Appliance
1. Press remote control OFF button.
2. Turn OFF all electric power to appliance if service is to be
performed.
3. Manual shut-off valve located behind lower grill. Turn manual
shut-off valve to OFF.
39
Maintenance
MAINTENANCE
The appliance is required to be inspected at least once a year by a professional service person.
The compartment below the firebox must be cleaned at least once a year. More frequent cleaning may be required due to excessive lint
from carpeting, bedding materials, or other fibrous materials. use a vacuum to clean all components at least once a year.
INSTALLATION AND REPAIR SHOULD BE DONE ONLY BY A QUALIFIED SERVICE PERSON. THE
APPLIANCE SHOULD BE INSPECTED BEFORE USE AND ANNUALLY BY A QUALIFIED SERVICE PERSON.
MORE FREQUENT CLEANING MAY BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING, BEDDING
MATERIALS, ETC. IT IS IMPERATIVE THAT CONTROL COMPARTMENTS, BURNERS AND CIRCULATION AIR
PASSAGEWAYS OF THE APPLIANCE BE KEPT CLEAN.
NOTE
Control Board System
•
•
•
Annual cleaning of burner system required. Vacuum all components thoroughly
Visually check for blocked port holes, especially near the pilot. Blocked port holes may cause delayed ignition
Visually check pilot light and burner when in operation. Flames should be steady, not lifting or floating
Pilot
Burner Orifice
Burner Ports
Fan
The fan should be disconnected from electrical current and cleaned (vacuumed) every six months. The bearings are sealed and require
no oiling.
Vent System
Annual examination of venting system by a qualified agency is required.
IF VENT-AIR INTAKE SYSTEM IS DISASSEMBLED FOR ANY REASON, REINSTALL PER INSTRUCTIONS PROVIDED WITH
INITIAL INSTALLATION.
The flow of combustion and ventilation air must not be obstructed.
Glass Cleaning & Replacement
•
Clean glass only when cool and only with non-abrasive, ammonia free cleansers
WARNING: DO NOT OPERATE APPLIANCE WITH GLASS/FRAME ASSEMBLY REMOVED, CRACKED OR BROKEN,
REPLACEMENT OF TH GLASS SHOULD ONLY BE PERFORMED BY A LICENSED OR QUALIFIED SERVICE PERSON.
Use protective gloves to handle any broken or damaged glass assembly components.
The glass assembly, part #INT-057T, shall only be replaced as a complete unit, as supplied by Hussong MFG. Co., INC.
Replacement of glass & frame assembly, part #UA8010, must only be perfored by a licensed or qualified service person
DO NOT SUBSTITUTE MATERIALS
Do not strike or slam glass door assembly
•
•
•
•
IMPORTANT
CAUTION
40
ANY SAFETY SCREEN OR GUARD REMOVED FOR SERVICING MUST BE REPLACED PRIOR TO
OPERATING THE APPLIANCE.
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN
CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER ORIENTATION AFTER SERVICING.
KEEP APPLIANCE AREA CLEAR OF COMBUSTIBLE MATERIALS, SUCH AS GASOLINE AND OTHER
FLAMMABLE VAPORS AND LIQUIDS.
Maintenance
Reflective Panel Kit Removal
1.
2.
3.
4.
5.
6.
7.
Use remote to turn fireplace off.
Shut off gas supply at manual shut-off valve. Disconnect gas line flex tube from the manual shut-off valve.
Unplug all components from electrical outlet, disconnect all wiring harnesses attached to gas valve.
Disconnect light kit communication link (black and white leads) from module communication link (black and white leads).
Remove upper hood, upper louver, glass assembly, and burner media*.
Remove 3 screws securing left side panel retainer. We recommend using a manual screwdriver to avoid damage to components.
Remove left side panel.
8. Remove upper left retainer clip.
9. Support the upper panel as you loosen the screws securing the upper panel retainer brackets. This will allow the brackets to slide
forward to facilitate removal of the upper panel.
10.
11.
Remove 3 screws from right side panel retainer bracket. Remove the retainer bracket.
Hold the rear panel and remove the right side panel.
41
Maintenance
12.
13.
14.
42
Remove rear panel.
Remove upper right retainer clip from right side panel.
Remove heat insulation shield.
Maintenance
Refractory Panel Kit Removal
1.
2.
3.
4.
5.
6.
7.
Use remote to turn fireplace off.
Shut off gas supply at manual shut-off valve. Disconnect gas line flex tube from the manual shut-off valve.
Unplug all components from electrical outlet, disconnect all wiring harnesses attached to gas valve.
Disconnect light kit communication link (black and white leads) from module communication link (black and white leads).
Remove upper hood, upper louver, glass assembly, and burner media*.
Remove 3 screws securing left side panel retainer. We recommend using a manual screwdriver to avoid damage to components.
Remove left side panel.
8. Support the upper panel as you loosen the screws securing the upper panel retainer brackets. This will allow the brackets to slide
forward to facilitate removal of the upper panel.
9. Remove the upper panel.
43
Maintenance
11.
12.
44
Remove 3 screws securing the right panel retainer.
Hold the rear panel as you remove the right panel. Remove the rear panel.
Maintenance
BURNER REMOVAL
CAUTION
If burner and/or pilot have been burning, use appropriate protection to avoid burns or damage to personal
property before removing any components.
WARNING
DO NOT OPERATE THIS FIREPLACE WITHOUT SEALING GASKET (LOCATED UNDER CONTROL
BOARD) IN PLACE. IF GASKETING IS DAMAGED, IT MUST BE REPLACED.
1. Use remote to turn fireplace off.
2. Shut off gas supply at manual shut-off valve. Disconnect gas line
flex tube from the manual shut-off valve.
3. Unplug all components from electrical outlet, disconnect all wiring
harnesses attached to gas valve.
4. Disconnect light kit communication link (black and white leads) from
module communication link (black and white leads).
5. Remove upper hood, upper louver, glass assembly, and logs.
6. Remove back burner; secured with screws, (2) at front, (2) at back.
7. Remove light kit cylinders, amber light filters, and halogen bulbs.
Remove screws securing light stands, lay light stands on control
board.
8. Remove side refractory panels.
9. Loosen front orifice bracket screws, push orifice backwards far
enough to release from venturi.
10. Remove front burner, secured with screws, (2) at front, (2) at back.
11. Remove (8) screws securing control board. Lift board up and out of
firebox.
45
Maintenance
BURNER INSTALLATION
WARNING
DO NOT OPERATE THIS FIREPLACE WITHOUT SEALING GASKET (LOCATED UNDER CONTROL
BOARD) IN PLACE. IF GASKETING IS DAMAGED, IT MUST BE REPLACED.
1. Place burner in firebox, aligning holes in burner to holes in firebox
bottom. Make sure gasket is in place on firebox bottom. Secure with
screws previously removed.
2. Reinstall front burner. Align front burner orifice with front venturi, pull
orifice bracket forward until orifice is seated inside venturi. Tighten
orifice bracket screws. Figure 20a. Secure burner with (4) screws
previously removed.
3. Reinstall side refractory panels.
4. Reinstall light kit stands (secure with screws previously removed),
halogen bulbs, cylinders and amber light filters.
5. Reinstall back burner assembly, making sure venturi is properly
positioned over back burner orifice. Figure 20a. Secure with 4
screws previously removed.
6. Reinstall log set.
7. Reconnect gas line to manual shutoff valve.
8. Reconnect all wiring harnesses to gas valve, Plug all components
into electrical outlet.
9. Reconnect light kit communication link (black and white leads) to
module communication link (black and white). (black to black, white
to white).
10. Reinstall glass frame assembly, upper hood and upper louver.
11. Turn gas on.
12. Verify proper log placement, operation of fireplace, and any
electrical components.
46
Maintenance
Troubleshooting
ATTENTION
TROUBLESHOOTING MUST BE PERFORMED BY A QUALIFIED TECHNICIAN.
Before proceeding with the steps in the following troubleshooting guide, verify the power supply is present and receiver batteries and/or
battery pack are fresh and installed with correct polarity.
Make sure all connections between wire harnesses and system components are proper and positive.
Make sure communication link between remote control and IFC control module is established.
Verify inlet pressure meets the recommended inlet pressure. If necessary adjust line pressure regulator.
PROBLEM
SOLUTION
PILOT WILL NOT LIGHT /
STAY LIT
•
•
•
Electrical power interrupted or disconnected. Restore electrical power to fireplace or use battery
backup. Ensure batteries are fully charged if using battery backup as power source.
Verify gas supply is turned on. Check remote shut-off valves from fireplace. usually there is a
valve near the main. there may be more than one valve between the fireplace and the main.
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line,
too narrow diameter pipe, low line pressure, or debris blockage (IE: spider's nests can often
cause blockages). Consult with plumber or gas supplier.
No LP in tank. Check LP (propane) tank. Refill if necessary.
Wiring disconnection. Use wiring schematic in this manual to determine that all wiring
connections are secure and correct.
Pilot flame not making contact with flame rectification sensor on pilot assembly. This valve is
equipped with a pilot flame adjustment screw. Adjust as necessary.
Pilot adjustment screw not sealed. Seal pilot adjustment screw. Do not over-tighten.
Pilot requires cleaning. Clean the pilot.
PILOT FLAME ALWAYS ON /
WILL NOT EXTINGUISH
•
System set to CPI mode. Set system to IPI mode.
MAIN FLAME WILL NOT
LIGHT
•
•
•
•
•
•
•
•
•
•
ON/OFF rocker switch in OFF position. Switch to ON position.
Remote not working properly. Replace batteries.
Remote set to thermostat mode and there is no call for heat. Adjust heat setting.
Thermostat disconnected or set too high. Set thermostat to lower temperature setting.
Ensure pilot flame will ignite. If not, see pilot flame troubleshooting above.
Ensure pilot flame is properly located to ignite main flame.
Plugged main burner orifice.
Wiring disconnection / improper wiring. Check for faulty or incorrect wiring.
Verify gas supply is turned on
Low gas pressure. Low gas pressure can be caused by several situations such as a bent line,
too narrow diameter pipe, or low line pressure. Consult with plumber or gas supplier.
PILOT AND BURNER
EXTINGUISH WHILE IN
OPERATION
•
•
•
•
•
•
•
No LP in tank. Check and refill if necessary.
Glass frame assembly not installed correctly. Refer to corresponding instructions in this manual.
Improper vent cap installation. Adjust if necessary.
Vent cap blockage. Remove debris if necessary.
Improper pitch on horizontal vent. 1/4" (6mm) rise per foot is required on horizontal venting.
Inner vent pipe leaking exhaust gases back into firebox. Check for leaks and repair if necessary.
Excessive draft
GLASS SOOTING
•
•
•
•
•
•
•
•
Improper log placement. Refer to corresponding pages in this installation manual.
Improper venturi setting. Venturi may need to be opened slightly to allow more air into the gas
mix.
Improper pitch on horizontal venting. 1/4" (6mm) rise per foot required on horizontal venting.
FLAME BURNS BLUE AND
LIFTS OFF BURNER
•
•
•
Improper venturi setting. Venturi may need to be closed slightly.
Improper vent cap installation. Check for proper vent cap installation.
Blockage or vent system leaks.
NO REACTION TO
COMMAND
•
•
Backup battery pack batteries or remote control batteries low. Replace batteries.
No communication between remote control and IFC control module. Reporgram remote control
to IFC control module. Follow INITIALIZING THE SYSTEM FOR THE FIRST TIME as outlined in
this manual.
A Maximum number of failed ignitions or flame restorations have been reached. Reset IFC
control module. See related section in this manual.
•
47
Maintenance
CONVERSION KIT INSTRUCTIONS
Part # UA2000: NG - LP Conversion Kit / UA2100: LP - NG Conversion Kit
WARNING
This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer's
instructions and all applicable codes and requirements of the authority having jurisdiction. If the
information in these instructions is not followed exactly, a fire, explosion or productions of carbon
monoxide may result, causing property damage, personal injury or loss of life. the qualified service
agancy is responsible for proper installation of this kit.The installation is not proper and complete until
operation of the converted appliance is checked as specified in the manufacturer's instructions supplied
with the kit. Refer to appliance owner's manual or product data plate for proper inlet and manifold pressure
adjustments and orifice sizing.
Kit includes:
• 1 Gas Conversion Label
• 1 Step Motor Pressure Regulator (308-6020 [LP] & 308-6023 [NG])
• 2 Burner Orifice LP #51 & #63 / NG #33 & #56 (301-0068)
CAUTION
WARNING
IMPORTANT
THE GAS SUPPLY SHALL BE SHUT OFF PRIOR TO DISCONNECTING THE ELECTRICAL POWER, BEFORE
PROCEEDING WITH THE CONVERSION.
SHUT OFF GAS SUPPLY AND ELECTRIC POWER TO FIREPLACE.
SHUT OFF GAS SUPPLY BEFORE DISCONNECTING ELECTRIC POWER.
For high altitude installations: Above 2000ft. (610m) US / 4500 ft. (1372m) Canada, consult the local gas
distributor or authority having jurisdiction for proper de-rating methods.
PREPARE THE FIREPLACE:
1. Remove upper hood, upper louver, glass assembly*.
2. Remove logs*.
3. Remove back burner assembly from fireplace*.
4. Loosen screws securing front orifice bracket, pull orifice backwards
out of front venturi.
*REFER TO CORRESPONDING PAGES IN THIS INSTALLATION
MANUAL IF NECESSARY.
REPLACE BURNER ORIFICE:
Remove existing orifice caps using wrench. Replace with orifice caps
included with kit, making sure to tighten caps securely.
Front burner orifice: (NAT #56 / LP #63)
Back burner orifice: (Nat #33 / LP #51)
PILOT CONVERSION
Using a 7/16" wrench and loosen the pilot hood 1/4 turn. Slide the tab at
the bottom of the orifice hood all the way so the red side (propane) with
the hole in it is showing. Tighten the pilot hood so that it is lined up with
the two probes on both sides of the pilot assembly.
48
Maintenance
CONVERT THE GAS CONTROL VALVE:
Follow stepper motor pressure regulator instruction sheet included
with conversion kit to convert gas valve. (LP or NAT marked on
stepper motor pressure regulator).
Verify that the following items are present in the package.
• Pressure regulator assembly (E)
• Two (2) screws (F)
• Identification label (G)
• Installation instructions
1. Shut off the gas supply to the valve and shut down the electric
supply.
2. See Fig. 1 to the right. Using a Torx T20, or slotted screwdriver,
remove and discard the two (2) pressure regulator mounting
screws (A), pressure regulator tower (B), and the spring and
diaphragm assembly (C), (if applicable).
3. Ensure the rubber gasket (D) which is prefitted as part of
assembly (E), is properly positioned, see Fig. 2, otherwise fit the
gasket as shown Fig. 2.
4. Install the new STEPPER MOTOR pressure regulator assembly,
as shown in Fig. 3 and Fig. 4. Use the supplied screws (F), M4
x 0.7 threaded length of thread L=(16 mm + 0 - 0.5 mm), steel
material, resistance class 8.8 (see Fig. 5).
5. Manually thread the two conversion kit mounting screws into
the valve body. Use a standard screwdriver or T20 Torx bit and
tighten the screws with a fixing torque of 25lb-in ± 5%.
IN THE EVENT THAT THE THREADS OF THE VALVE ARE
STRIPPED OR DAMAGED, REPLACE THE VALVE.
6. Install the enclosed identification label (G) to the valve body
where it can be easily seen.
7. Make STEPPER MOTOR and valve electrical connections, apply
gas to system and relight appliance according to manufacturers
instructions.
8. With the main burner "ON", test the new pressure regulator
assembly for leaks using a soap solution.
9. Relight the main burner and verify proper burner ignition and
operation.
WARNING
Installation should be carried out in a clean environment.
WARNING
This modulating conversion kit must ONLY be applied as part of a conversion kit supplied by the
APPLIANCE MANUFACTURER for the specific appliance, and type of gas, being converted.
WARNING
Correct operation of the system cannot be guaranteed if the conversion kit or valve has been dropped or
has sustained a strong impact.
INSTALLER
NOTICE
The instruction sheet included with the kit must be left with the appliance.
49
Maintenance
COMPLETE THE CONVERSION:
1. Adjust front burner venturi setting by loosening screw, adjusting cap and
retightening screw. NAT: 100% closed / L.P: 5/8" (16mm) open.
2. Reinstall front burner. Pull front orifice bracket forward until orifice is properly
seated in front venturi. Tighten screws*. Figure 37a.
3. Reinstall back burner assembly into fireplace, checking to ensure burner
venturi is properly seated over burner orifice*. Figure 37a.
4. Back (main) burner venturi adjustment handle is attached to underside of
control board. Access through lower grill opening. Loosen wing nuts, adjust
as necessary, pulling handle forward to open, pushing backwards to close.
Tighten wing nuts:
NAT: 1/8" (3mm) open - handle pushed back
LP: 5/8" (16mm) open - handle pulled forward
5. Reinstall logs*.
6. Turn on gas and electrical supplies.
7. Light fireplace*. Check for leaks at all connections with a gas leak detector.
8. Test inlet pressure*.
9. Visually check pilot flame. Flame should envelope top of flame sensor and
extend onto burner far enough for proper ignition.
To Adjust Pilot: Turn pilot adjustment screw clockwise to decrease or counterclockwise to increase pilot flame.
10. Turn fireplace off.
11. Affix gas type sticker to existing label.
12. Reinstall glass frame assembly, upper louver and upper hood*.
13. Complete and affix Gas Conversion label behind lower grill.
*REFER TO CORRESPONDING PAGES IN THIS INSTALLATION MANUAL IF
NECESSARY.
50
Maintenance
REPLACEMENT PARTS LIST - (UFO100)
Item #
Item Description
200-0100-01
Owner’s Manual
314-0009
Glass Gasket (125 inches required)
308-6011
SIT Pro Flame II Electronic Control Module
308-6014
SIT Pro Flame II Handheld Transmitter
308-6027
SIT 885 Gas Valve c/w Step Motor (0.885.009)
305-6002
Module Main Wiring Harness (5 wire)
305-6003
Valve Wiring Harness (4 wire)
305-0060
Battery Back-up
301-0068
Orifice (Main Burner Orifice) Drill to # 56 & #33 DMS for Natural Gas
301-0068
Orifice (Main Burner Orifice) Drill to # 63 & #51 for LP (Propane) Gas
308-0123
Pilot Assembly, conv. PSE IPI (SIT connections)
UA8100
Burner Assembly - Log Burner
UA8101
Front Burner
UA8010
Door Assembly
305-6301
Light Socket (120V / 1000W)
305-6303
Light Bulb (120V / 35W)
UA2100
Conversion Kit LP to NG
UA2000
Conversion Kit NG to LP
305-0224
Replacement Blower
754-0057
Upper Hood
754-0065
Eye Brow ( low profile hood used with door kits)
754-0058
Top Louver
800-0102
Lower Louver Assembly
UA0150
Refractory Panel Set (4 pc.)
UA0150LS
Left Side Panel
UA0150RS
Right Side Panel
UA0150T
Top Panel
UA0150R
Rear Panel
310-U501
Complete 12pcs Log Set
310-U501-1
LOG # 1
310-U501-2
LOG # 2
310-U501-3
LOG # 3
310-U501-4
LOG # 4
310-U501-5
LOG # 5
310-U501-6
LOG # 6
310-U501-7
LOG # 7
310-U501-8
LOG # 8
310-U501-9
LOG # 9
310-U501-10
LOG # 10
310-U501-11
LOG # 11
310-U501-12
LOG # 12
310-0020
Black Embers
305-6313
Amber Lens (2 Required)
UF0100/0110-BS
Barrier Screen
Unit
51
Warranty
LIMITED WARRANTY
LIMITED 10 YEAR WARRANTY
This limited 10 Year Warranty will not become effective until the Warranty Registration Form has been completed and mailed to
Archgard Fireplace Products 7116 Beatty Drive, Mission, BC V2V 6B4 Canada. This registration form must be received within 30 days
of installation. Failure to do so may result in delayed warranty coverage and submission of proof of purchase will be required.
Archgard Fireplace Products warranties to the original purchaser of this Ambiance Fireplace, that is free from defects in materials and
workmanship at the time of manufacture. Subject to the following conditions & requirements, Archgard Fireplace Products extends the
following limited warranty under normal use and service, with respect to the Ambiance line of gas burning fireplaces.
YEAR 1: subject to the conditions & requirements listed below, within the first year from date of purchase, Archgard Fireplace Products
shall, at it’s discretion, replace or repair any such defect in material or workmanship at Archgard Fireplace Product’s expense, including
reasonable labor costs to repair or replace the defective component, if a factory pre-authorization is give for the repair.
YEARS 2-10: subject to the conditions and requirements listed below, beginning with the first day of the second year and continuing
through the tenth year, Archgard Fireplace Products, will at it’s discretion, provide repair or replacement parts at current list prices for
any defect in materiel or workmanship of components, including optional components and accessories (if available). Archgard Fireplace
Products shall not be responsible for any installation, labor, transportation of other indirect costs.
LIMITATION OF LIABILITY
To make a claim under this warranty, the purchaser must first contact the dealer/installer from whom the fireplace was purchased.
This limited warranty will be void if the fireplace is not installed by a qualified installer and according to the installation instructions. Use
of unauthorized components will make this warranty null and void. This limited warranty also is void if the fireplace is not operated, at all
times, according to the operating instructions furnished.
This warranty is limited to defects in material and workmanship. It does not apply to any product that has been subject to negligence,
misapplication, improper installation. No person is authorized to extend the time of this warranty or to accept on Archgard Fireplace
Product’s behalf any additional obligation of liability connected with the unit.
It is expressly agreed and understood that this warranty is Archgard Fireplace Product’s sole obligation and purchaser’s exclusive
remedy for defective fireplace equipment. Archgard Fireplace Products shall not be liable for any consequential, incidental or contingent
damages whatsoever. The forgoing warranty is exclusive and in lieu of all other express warranties. Archgard Fireplace Products
shall not be held to implied warranties or merchantability and fitness for a particular purpose. This warranty replaces all previous
warranty policies.
Some states do not allow the exclusion or limtation of incidental or consequential damages or limitations on how long an implied
warranty lasts, so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
Archgard Fireplace Products reserves the right to make changes at any time, without notice, in design material, specifications and
prices. Archgard Fireplace Products reserves the right to discontinue models and product.
WARRANTY CONDITIONS & REQUIREMENTS:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
52
You are the original purchaser. This warranty is not transferable.
Installation of the fireplace is performed by a factory authorized installer.
Installation and operation must comply with installation and operation instructions.
Paint and glass gaskets are covered for 30 days from date of purchase.
Remote controls and all optional accessories are covered for 1 year from date of purchase.
This warranty does not offer coverage for Light Bulbs or Batteries (whether factory, dealer or installer supplied). This includes any
damage stemming from either component's nonuse.
Components broken, (including glass panels), during shipping, careless handling of components, or defects resulting from
improper installation, misuse of the fireplace and components are not covered under this warranty.
This warranty does not cover any part of the fireplace or any components which have been exposed to or submerged under
water.
Archgard Fireplace Products must be notified by the dealer the fireplace was purchased from or a qualified installer/service
technician of the defect.
Annual service of the fireplace as required in the installation manual, is performed by a factory authorized installer / service
technician. (Copies of such service records may be required to claim a warranty).
All previous warranty / service has been performed by a factory authorized installer or service technician. (Copies of such service
records may be required to claim a warranty).
Effective March 2015
Warranty
LIFETIME WARRANTY
LIFETIME WARRANTY
THIS LIFETIME WARRANTY COVERAGE WILL BE EXTENDED AS DESCRIBED BELOW PROVIDED ALL WARRANTY
CONDITIONS AND REQUIREMENTS ARE MET AS OUTLINED IN THE 10 YEAR LIMITED WARRANTY POLICY.
LIFETIME WARRANTY COVERAGE
LIFTIME WARRANTY IS EXTENDED AS FOLLOWS: Archgard Fireplace Products warranties the original purchaser that the firebox,
heat exchanger, fiber logs, burner tube and glass panel of this Ambiance Fireplace will not be defective in material or workmanship
under normal use and service for as long as you own this product. If any of these components fail due to defects in material and
workmanship under normal use and service Archgard Fireplace Products will, at its sole discretion, repair or replace the defective
component. This LIFETIME WARRANTY does not cover any installation, labor, transportation or other indirect cost arising from
defective components.
LIMITATION OF LIABILITY
This Lifetime Warranty will be void if the fireplace is not installed by a factory authorized installer and according to the installation
instructions. Use of unauthorized components will make this warranty null and void. This Lifetime Warranty also is void if the fireplace
is not operated, at all times, according to the operating instructions furnished. This warranty is limited to defects in material and
workmanship of components specified. It does not apply to any product that has been subject to negligence, misapplication, improper
installation.
No person is authorized to extend the time of this warranty or to accept on Archgard Fireplace Product’s behalf, any additional
obligation of liability connected with the unit.
Archgard Fireplace Products may fully discharge all obligations with respect to this Lifetime Warranty by refunding the wholesale
price of the defective component(s).
It is expressly agreed and understood that this Lifetime Warranty is Archgard Fireplace Product’s sole obligation and original
purchaser’s exclusive remedy for defective fireplace equipment. Archgard Fireplace Products shall not be liable for any consequential,
incidental or contingent damages whatsoever other than those incurred by Archgard Fireplace Products to repair or replace the
defective component. The foregoing warranty is exclusive and in lieu of all other expressed warranties. Archgard Fireplace Products
shall not be held implied warranties, including but not limited to the implied warranties or merchantability and fitness for a particular
purpose. This lifetime warranty replace all previous lifetime warranty policies.
Archgard Fireplace Products reserves the right to make changes at any time without notice, in design, material, specifications and
prices. Archgard Fireplace Products reserves the right to discontinue models and products.
To activate this Lifetime Warranty coverage, this registration card must be completed and mailed within 30 days of installation
to the following address:
ARCHGARD FIREPLACE PRODUCTS
7116 BEATTY DRIVE
MISSION, BC V2V 6B4
Effective March 2015
CUT ALONG DOTTED LINE
CANADA
PURCHASER NAME:
INSTALLATION DATE:
ADDRESS:
MODEL #:
SERIAL #:
TELEPHONE:
INSTALLER NAME:
ADDRESS:
TELEPHONE:
53
NOTES
NOTES
January 5 2017