INSTRUCTIONS
REV. 09-18-03
-J01522
®
Kit Number 67224-95C
FXD (Dyna Super Glide) TACHOMETER KIT
General
4973
Speedometer sensor
connector [65]
This kit is designed for installation on 1995 - 2003 FXD Dyna Super
Glide motorcycles equipped with an electronic speedometer and no
tachometer.
NOTE
USE THE APPROPRIATE SERVICE MANUAL PROCEDURE!
Service Manuals are available from your Harley-Davidson dealer. If
the procedure is not within your capabilities or you do not have the
correct tools, have your Harley-Davidson dealer perform the
installation.
erman
G
.
e
.
y
n
o p. d e
Find the appropriate model year of your motorcycle and follow the
instructions given underneath. All model motorcycles will follow the
same Final Adjustments and Checks given on the last page of this
instruction sheet.
1995 Models
Figure 1. Speedometer Sensor Connection [65]
See Figure 1. The 3-place speedometer sensor connector
[65] is located on the frame beneath the seat. Remove
connector from t-stud and disconnect. Cut cable tie holding
sensor wires to right rear frame tube.
1WARNING
1d. Refer to applicable Service Manual procedure and remove
headlamp, for work clearance.
To prevent accidental vehicle start-up, which could
cause death or serious injury, disconnect battery cables
(negative cable first) before proceeding.
w
w
1WARNING
w.
2.
Remove handlebar clamp screws securing speedometer
bracket. Remove speedometer, bracket, and harness.
1995 MODELS, REMOVAL OF ELECTRONIC
SPEEDOMETER AND BRACKET
1a. Refer to applicable Service Manual procedure and remove
seat.
1b. Refer to applicable Service Manual procedure and remove
fuel tank.
1WARNING
Stop the engine when refueling or servicing the fuel system. Do
not smoke or allow open flame or sparks near gasoline.
Gasoline is extremely flammable and highly explosive, which
could result in death or serious injury. (00002a)
n
e
1995 MODELS, DISCONNECT MAIN WIRING HARNESS
8-PLACE CONNECTOR [21B, A] (FIGURE 2)
h d o nli
Disconnect negative (-) battery cable first. If positive (+)
cable should contact ground with negative (-) cable
connected, the resulting sparks can cause a battery
explosion, which could result in death or serious injury.
(00049a)
1.
1e
sh
Rosto
ck
To install this kit, you will be removing the following: seat, fuel tank,
speedometer bracket, speedometer (some models), and indicator
lights. You will also have to disconnect the electronic speedometer
harness from the 3-place connector under the seat and disconnect
the 12-place or 14-place connector under the headlamp. Read all
the applicable Service Manual instructions carefully before you
begin the tachometer installation. Connector numbers in brackets,
for example [65], are the identifying numbers used in Service Manual
wiring diagrams.
2a. Disconnect the battery, negative cable first. Refer to
applicable Service Manual procedure and disconnect main
wiring harness 8-place connector [21A, B], at the front of
the motorcycle.
3.
1995 MODELS, REMOVE SPEEDOMETER LEADS FROM
8-PLACE CONNECTOR [21B, A] (FIGURE 2)
3a. See Figure 2 and Service Manual wiring schematic. Pull
the following wires and terminals out of connector [21B].
Wire Color
Orange/white
White/green
Black
Cavity Number
5
1
2
3b. Remove the large female connector from the fuel gauge
black wire.
3c. Slide the wires removed in step 2a out of the plastic
conduit covering the wires connected to the 8-place
connector.
1c. Remove speedometer sensor cable from mounting clips
under tank.
1 of 7
Splices
i00240-.tif
0
erman
G
.
e
.
y
n
1995 MODELS, REMOVE INDICATOR LAMPS FROM
BRACKET
7.
7a. See Figure 4. Assemble the harness for 1995 models as
shown from wires, conduit and connector provided in kit.
The connector cavity numbers are shown on socket
housing (12) and wires must be inserted as follows:
4a. Remove the screws that secure the indicator lamps
assembly to the speedometer bracket. Retain screws and
indicator lamps assembly for installation on
speedometer/tachometer bracket later.
5.
7b. This harness will plug directly into the back of the
tachometer. After plugging wire ends into connector as
shown, cover wires with conduit from kit.
w
w
w.
sh
5b. See Figure 3. Note position of rear speedometer gasket
and remove it. Push on rear of speedometer while
simultaneously pulling speedometer and front gasket from
bracket. Do not remove front gasket from the
speedometer.
7c. Use wire clamp to secure conduit inside tachometer. Install
rear tachometer gasket using the same procedure as for
the speedometer. Install cover.
h d o nli
1995 MODELS, INSTALL SPEEDOMETER IN KIT
BRACKET
6a. See Figure 5. Place wires from speedometer through front
of left opening in double bracket. Lubricate the front and
rear gaskets with isopropyl alcohol or glass cleaner to
ease installation.
6b. Insert speedometer into the front of the double bracket. Be
sure wire guides are aligned with opening at bottom of
bracket.
6c. Place rear gasket in position and align gasket tabs. Work
gasket into space between speedometer and bracket by
pushing speedometer against one side of bracket while
pushing gasket into position at the opposite side.
Cavity Number
1
2
3
Wire Color
Orange
Black
Pink
1995 MODELS, REMOVE SPEEDOMETER FROM
BRACKET
5a. Unscrew boot from speedometer reset switch. Remove
cover screws and rear cover.
6.
1995 MODELS, ASSEMBLING TACHOMETER HARNESS
o p. d e
4.
Rosto
ck
Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A]
8.
n
e
1995 MODELS, CONNECT SPEEDOMETER/
TACHOMETER LEADS
8a. Cut speedometer black ground lead 7.5 in. from bottom of
speedometer case and strip 3/8 in. insulation.
8b
Cut speedometer orange/white lead 5.5 in. from bottom of
speedometer case and strip 3/8 in. insulation.
8c. See Figures 6 and 2. Use one of the butt connectors from
the kit and connect the ground leads as shown. Refer to
“SEALED BUTT CONNECTORS” in the appropriate
Service Manual for complete procedure.
8d. Repeat step 8c for the speedometer orange/white and
tachometer orange leads.
6d. Add amber bulb assembly from kit to speedometer in order
for tachometer and speedometer backlighting to match.
6e. Replace cover and boot from reset switch.
-J01522
2 of 7
12
4871
11
1995
12
13
1996
1997
1998
14
15
12
13
Rear
gasket
1999
and later
Bracket
Speedometer &
Front gasket
15
17
clip
terminal off
orange wire
end [13]
13
10 Conduit
from kit
erman
G
.
e
.
y
n
Figure 3. Speedometer and Gaskets in Single
Instrument bracket
1995 MODELS, CONNECT SPEEDOMETER/
TACHOMETER LEADS TO 8-PLACE CONNECTOR
9a. Tape the wires, with socket terminals on their ends,
together and slide them through conduit from kit until
terminals are positioned at 8-place connector.
Figure 4. Connecting Harness to Tachometer
(Callouts correspond to wires listed in Service Parts)
Instrument
Speedometer/Tachometer
Speedometer
Speedometer/Tachometer
Tachometer
Wire Color
Orange/white
White/green
Black
Pink
Cavity Number
5
1
2
3
10. 1995 MODELS, INSTALL INDICATOR LIGHTS ON DUAL
BRACKET
10a. See Figure 8. Place the indicator light bezel and color strip
on front of dual bracket. Be sure color strip is positioned on
locating pins.
w
w
w.
1996 - 1998 Models
1WARNING
To prevent accidental vehicle start-up, which could
cause death or serious injury, disconnect battery cables
(negative cable first) before proceeding.
1.
1996-1998 MODELS, REMOVAL OF ELECTRONIC
SPEEDOMETER AND BRACKET
11a. See Figure 8. Place speedometer/tachometer assembly in
position and install screws, but do not tighten.
11b. Connect large female connector to fuel gauge black wire.
11c. Connect the 8-place wiring harnesses.
11d. See Figure 1. Route speedometer sensor cable into
position under fuel tank and seat and connect 3-place
connector [65]. Place speedometer sensor cable into clips
underneath fuel tank. Replace cable ties holding connector
[65] to frame.
e
1a. Refer to applicable Service Manual procedure and remove
seat.
h d o nli
10b. Install indicator light socket assembly on rear of dual
bracket. Be sure locating pins on bezel enter holes in
socket assembly. Install mounting screws.
11. 1995 MODELS, INSTALL SPEEDOMETER/
TACHOMETER
o p. d e
9b. See Figure 2. Remove tape from wires. Insert terminals
into 8-place connector as follows:
sh
Rosto
ck
9.
15
n
1b. Refer to applicable Service Manual procedure and remove
fuel tank.
1WARNING
Stop the engine when refueling or servicing the fuel
system. Do not smoke or allow open flame or sparks
near gasoline. Gasoline is extremely flammable and
highly explosive, which could result in death or serious
injury. (00002a)
1c. Remove speedometer sensor cable from mounting clips
under tank.
11e. Refer to Service Manual procedures and install main
wiring harness.
See Figure 1. The 3-place speedometer sensor connector
[65] is located on the frame beneath the seat. Remove
connector from t-stud and disconnect. Cut cable tie holding
sensor wires to right rear frame tube.
11f. Refer to Service Manual procedures and install fuel tank.
Use hose clamp in kit.
1d. Refer to applicable Service Manual procedure and remove
headlamp, for work clearance.
11g. Install headlamp, if removed. Continue to the Final
Adjustment and Checks given on the last page of
this instruction sheet.
1e
-J01522
Remove handlebar clamp screws securing speedometer
bracket. Remove speedometer, bracket, and harness.
3 of 7
Gasket
5089
i00235-.eps
Speedometer
Orange/white or black wire
Butt connector
Gasket tabs
Tachometer
Orange/white or black wire
erman
G
.
e
.
y
n
Socket terminal
Figure 5.Back of Speedometer
Figure 6. Connect Speedometer and Tachometer Wires
rear gaskets with isopropyl alcohol or glass cleaner to
ease installation.
NOTE
The main wiring harness is routed through the frame top tube. It is
designed with enough slack to pull the main wiring harness
connector out of the top tube so the connector can be disconnected.
Refer to applicable Service Manual procedure and disconnect main
wiring harness connector [20A, B], at the front of the motorcycle.
o p. d e
3.
6b. Insert speedometer into the front of the double bracket. Be
sure wire guides are aligned with opening at bottom of
bracket.
6c. Place rear gasket in position and align gasket tabs. Work
gasket into space between speedometer and bracket by
pushing speedometer against one side of bracket while
pushing gasket into position at the opposite side.
1996 - 1998 MODELS -REMOVE SPEEDOMETER LEADS
FROM 12-PLACE OR 14-PLACE CONNECTOR [20B]
(NOT SHOWN)
6d. Add amber bulb assembly from kit to speedometer in order
for tachometer and speedometer backlighting to match.
3a. See Service Manual wiring schematic. Pull the following
wires and terminals out of connector [20B].
Cavity Number
1
2
12
w
w
Wire Color
Orange/white
White/green
Black
6e. Replace cover and boot from reset switch.
7.
w.
h d o nli
1996-1998 MODELS, REMOVE INDICATOR LAMPS
FROM BRACKET
7c. Use wire clamp to secure conduit inside tachometer. Install
rear tachometer gasket using the same procedure as for
the speedometer. Install cover.
5a. Unscrew boot from speedometer reset switch. Remove
cover screws and rear cover.
6.
1996-1998 MODELS, INSTALL SPEEDOMETER IN KIT
BRACKET
6a. See Figure 5. Place wires from speedometer through front
of left opening in double bracket. Lubricate the front and
-J01522
Cavity Number
1
2
3
7b. This harness will plug directly into the back of the
tachometer. After plugging wire ends into connector as
shown, cover wires with conduit from kit.
1996-1998 MODELS, REMOVE SPEEDOMETER FROM
BRACKET
5b. See Figure 3. Note position of rear speedometer gasket
and remove it. Push on rear of speedometer while
simultaneously pulling speedometer and front gasket from
bracket. Do not remove front gasket from the
speedometer.
n
Wire Color
Orange
Black
Pink
4a. Remove the screws that secure the indicator lamps
assembly to the speedometer bracket. Retain screws and
indicator lamps assembly for installation on
speedometer/tachometer bracket later.
5.
e
7a. See Figure 4. As dictated by model year, assemble one of
the harnesses shown from wires, conduit and connector
provided in kit. The connector cavity numbers are shown
on socket housing (12) and wires must be inserted as
follows:
3b. Slide the wires removed in step 1 out of the plastic conduit
covering the wires connected to the 12-place connector.
4.
1996-1998 MODELS, ASSEMBLING TACHOMETER
HARNESS
sh
1996 -1998 MODELS - DISCONNECT MAIN WIRING
HARNESS 12-PLACE OR 14-PLACE CONNECTOR [20B,
A] (NOT SHOWN)
Rosto
ck
2.
8.
1996-1998 MODELS, CONNECT SPEEDOMETER/
TACHOMETER LEADS
8a. Cut speedometer black ground lead 7.5 in. from bottom of
speedometer case and strip 3/8 in. insulation.
8b. See Figures 6 and 2. Use one of the butt connectors from
the kit and connect the ground leads as shown. Refer to
“SEALED BUTT CONNECTORS” in the appropriate
Service Manual for complete procedure.
4 of 7
4870
Indicator lights
4866
Figure 7. Speedometer (r) and Tachometer (l)
Installed in Double Bracket
(Rear Covers Removed for Illustration Purposes)
9.
1996-1998 MODELS, CONNECT SPEEDOMETER/
TACHOMETER LEADS TO 12-PLACE OR 14-PLACE
CONNECTOR
Figure 8. Kit Installed
and Later Models
er1999
ma
G
.
ny 1
e
.
n
Instrument
Speedometer
Speedometer
Speedometer/Tachometer
Tachometer
Tachometer
Wire Color
Orange/white
White/green
Black
Pink
Orange
Cavity Number
1
2
12
7
6
To prevent accidental vehicle start-up, which could
cause death or serious injury, disconnect battery cables
(negative cable first) before proceeding.
1.
1a. Disconnect battery, negative cable first. Remove seat
according to Service Manual instructions.
1b. Refer to applicable Service Manual procedure and remove
headlamp, for work clearance.
10. 1996-1998 MODELS, INSTALL INDICATOR LIGHTS ON
DUAL BRACKET
10a. See Figure 8. Place the indicator light bezel and color strip
on front of dual bracket. Be sure color strip is positioned on
locating pins.
10b. Install indicator light socket assembly on rear of dual
bracket. Be sure locating pins on bezel enter holes in
socket assembly. Install mounting screws.
w
w
w.
11. 1996-1998 MODELS, INSTALL SPEEDOMETER/
TACHOMETER
1c. Remove handlebar clamp screws securing speedometer
bracket. Remove speedometer, bracket, and harness.
2.
1999 AND LATER MODELS - DISCONNECT MAIN
WIRING HARNESS 12-PLACE OR 14-PLACE
CONNECTOR [20B, A] (NOT SHOWN)
11c. See Figure 1. Route speedometer sensor cable into
position under fuel tank and seat and connect 3-place
connector [65]. Place speedometer sensor cable into
clips underneath fuel tank. Replace cable ties holding
connector [65] to frame.
11d. Install main wiring harness according to Service Manual
procedures.
11e. Install fuel tank with hose clamp from kit according to
Service Manual procedures.
11f. Install headlamp, if removed. Continue to the Final
Adjustment and checks given on the last page of
this instruction sheet.
e
NOTE
The main wiring harness is routed through the frame top tube. It is
designed with enough slack to pull the main wiring harness
connector out of the top tube so the connector can be disconnected.
Refer to applicable Service Manual procedure and disconnect main
wiring harness connector [20A, B], at the front of the motorcycle.
h d o nli
11a. See Figure 8. Place speedometer/tachometer
assembly in position and install screws, but do not
tighten.
11b. Connect the 12-place or 14-place wiring harnesses.
-J01522
1999 AND LATER MODELS, REMOVAL OF
ELECTRONIC SPEEDOMETER AND BRACKET
o p. d e
9b. Remove tape from wires. Insert terminals into connector
as follows:
WARNING
sh
Rosto
ck
9a. Tape the wires, with socket terminals on their ends,
together and slide them through conduit from kit until
terminals are positioned at 12-place or 14-place connector.
3.
n
1999 AND LATER MODELS -REMOVE SPEEDOMETER
LEADS FROM 12-PLACE OR 14-PLACE CONNECTOR
[20B] (NOT SHOWN)
3a. See Service Manual wiring schematic. Pull the following
wires and terminals out of connector [20B].
Wire Color
Orange/white
White/green
Black/yellow
Black
Cavity Number
1
2
10
12
3b. Slide the wires removed in step 3a out of the plastic
conduit covering the wires connected to the 12-place
connector.
5 of 7
4.
1999 AND LATER MODELS REMOVE INDICATOR
LAMPS FROM BRACKET
8.
4a. Remove the screws that secure the indicator lamps
assembly to the speedometer bracket. Retain screws and
indicator lamps assembly for installation on
speedometer/tachometer bracket later.
5.
8a. Cut speedometer black ground lead 7.5 in. from bottom of
speedometer case and strip 3/8 in. insulation.
8b. Cut speedometer orange/white lead 5.5 inches from
bottom of speedometer case and strip 3/8 inch insulation.
After clipping the terminal from the orange wire of
tachometer harness, strip 3/8 inch insulation.
1999 AND LATER MODELS REMOVE SPEEDOMETER
FROM BRACKET
8c. See Figures 6 and 2. Use one of the butt connectors from
the kit and connect the ground leads as shown. Refer to
“SEALED BUTT CONNECTORS” in the appropriate
Service Manual for complete procedure.
5a. Remove cover screws and rear cover. Remove connector
from back of speedometer.
5b. See Figure 3. Note position of rear speedometer gasket
and remove it. Push on rear of speedometer while
simultaneously pulling speedometer and front gasket from
bracket. Do not remove front gasket from the
speedometer.
1999 AND LATER MODELS INSTALL SPEEDOMETER
IN KIT BRACKET
6a. See Figure 5. Lubricate the front and rear gaskets with
isopropyl alcohol or glass cleaner to ease installation.
Insert speedometer into the front of left opening in double
bracket.
6d. Replace cover ensuring reset switch is properly aligned.
Tighten screws.
1999 AND LATER MODELS ASSEMBLING
TACHOMETER HARNESS
7a. See Figure 4. As dictated by model year, assemble one of
the harnesses shown from wires, conduit and connector
provided in kit. The connector cavity numbers are shown
on socket housing (12) and wires must be inserted as
follows:
w
w
Cavity Number
1
2
3
1999 AND LATER MODELS CONNECT
SPEEDOMETER/TACHOMETER LEADS TO 12-PLACE
OR 14-PLACE CONNECTOR
9a. Tape the wires, with socket terminals on their ends,
together and slide them through conduit from kit until
terminals are positioned at 12-place or 14-place connector.
9b. Remove tape from wires. Insert terminals into connector
as follows:
Instrument
Wire Color
Cavity Number
Speedometer
Orange/white
1
Speedometer
White/green
2
Speedometer/Tachometer Black
12
Tachometer
Pink
7
Tachometer
Orange
6
o p. d e
Rosto
ck
6c. Place rear gasket in position and align gasket tabs. Work
gasket into space between speedometer and bracket by
pushing speedometer against one side of bracket while
pushing gasket into position at the opposite side.
Wire Color
Orange
Black
Pink
9.
erman
G
.
e
.
y
n
6b. Reinstall connector removed in step 5a and align wires
through wire guides.
7.
8d. Repeat Step 8c for the speedometer orange/white and
tachometer orange leads.
9c. Use the tie wraps supplied in the kit to secure the 1/2”
conduit containing the tachometer/speedometer wires to
the indicator light assembly
10. 1999 AND LATER MODELS INSTALL INDICATOR
LIGHTS ON DUAL BRACKET
10a. See Figure 8. Place the indicator light bezel and color strip
on front of dual bracket. Be sure color strip is positioned on
locating pins.
sh
6.
1999 AND LATER MODELS, CONNECT SPEEDOMETER/
TACHOMETER LEADS
10b. Install indicator light socket assembly on rear of dual
bracket. Be sure locating pins on bezel enter holes in
socket assembly. Install mounting screws.
w.
7c. Use wire clamp to secure conduit inside tachometer. Install
rear tachometer gasket using the same procedure as for
the speedometer. Install cover.
n
e
11. 1999 AND LATER MODELS INSTALL SPEEDOMETER/
TACHOMETER
h d o nli
7b. This harness will plug directly into the back of the
tachometer. After plugging wire ends into connector as
shown, cover wires with conduit from kit.
11a. See Figure 8. Place speedometer/tachometer assembly in
position and install screws, but do not tighten.
11b. Connect the 12-place or 14-place wiring harnesses.
11c. Install main wiring harness according to Service Manual
procedures.
11d. Install headlamp, if removed. Continue to the Final
Adjustment and Checks given on the last page of
this instruction sheet.
-J01522
6 of 7
FINAL ADJUSTMENTS AND CHECKS - ALL MODELS
1.
1WARNING
If necessary, adjust handlebar to rider’s normal riding
position.
After installing seat, pull upward on front of seat to be
sure it is in locked position. While riding, a loose seat
can shift causing loss of control, which could result in
death or serious injury. (00070a)
NOTE
When handlebar installation is complete, the upper and lower
clamps are in contact with the cast-in boss in front and have a
slight gap at the rear.
4.
Turn ignition/light switch to ON. Check that the indicator
lights, signal lights, and headlamp all function properly.
5.
Start the engine. Check the tachometer operation and check
that indicator lights are working correctly.
Tighten two rear screws until cast-in spacers of upper clamp
contact handlebar lower clamps. Tighten front screws to 1215 ft-lbs (16-20 Nm). Final tighten rear screws to 12-15 ft-lbs
(16-20 Nm).
6
If tachometer does not function, check that all wiring
connections were correctly made.
7.
Be sure steering turns freely, lock-to-lock.
A slight gap, between upper and lower clamp, should be
visible from the front.
8.
Test ride motorcycle to verify speedometer is functioning
properly.
See Figure 7. Loosen four screws of handlebar upper
clamp.
Place and hold handlebar in normal riding position.
1WARNING
erman
G
.
e
.
y
n
2.
Connect battery cables, positive cable first.
3.
Install seat.
®
Service Parts
i03086
2
Part No. 67224-95C
o p. d e
Rosto
ck
Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)
Tachometer Kit
6
w
w
8
10
sh
3
9
w.
h d o nli
ITEM
10
11
12
13
4
ITEM
1
2
3
4
5
6
7
8
9
DESCRIPTION
Screw, cover #8-32 x 11/64 in (2)
Hose clamp (2)
Cable strap (6)
Tachometer
Cover, tachometer rear
Gasket, rear
Bracket, speedo/tach
Gasket, front
Butt splice blue (2)
-J01522
PART NO.
2361
9946
10006
67042-99
67103-95
67344-97
67338-97
67345-97
70586-93
14
15
16
17
18
Date 9/03
n
1
5
e
7
DESCRIPTION
*Conduit, 1/2” diameter
*Socket/Amp Mate-N-Lok
*Pink wire
6-place Socket housing
Socket/Amp Socket
*Orange wire
Socket/Amp socket
*Pink Wire
Socket/no terminal
*Black wire
Bulb assembly-amber (not shown)
Socket/Deutsch socket
*Pink Wire
*Conduit, 5/16” diameter
PART NO.
not sold
68826-99
72081-99
68944-98
68946-98
68947-98
67385-98
68987-99
Not sold
* Not Shown-See Figure 4 for instructions on assembling
connector, wires and conduit into a harness.
7 of 7
Download PDF