Instructions - Parts List
APEX
Oil Transfer Pump
311305E
EN
For pumping non-flammable fluids, including motor oils, hydraulic
fluid, and antifreeze only. Do not use to pump water.
Model 260100, 5.8 gpm (22.0 lpm), 65 psi (.45 MPa, 4.5 bar) 12 VDC
Model 260101, 4.25 gpm (16.1 lpm), 65 psi (.45 MPa, 4.5 bar) 115 VAC
Model 260102, 8.0 gpm (30.3 lpm), 30 psi (.21 MPa, 2.1 bar) 115 VAC
Model 260104, 4.25 gpm (16.1 lpm), 65 psi (.45 MPa, 4.5 bar) 230 VAC
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001
Warnings
Warnings
The following general warnings are for the setup, use, grounding, maintenance, and repair of this
equipment. Additional, more specific warnings may be found throughout the body of this manual
where applicable. Symbols appearing in the body of the manual refer to these general warnings.
When these symbols appear throughout the manual, refer back to these pages for a description
of the specific hazard.
WARNING
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield
wiper fluid, be aware that flammable fumes can ignite or explode. To help prevent fire
and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources, such as cigarettes and portable electric lamps.
• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes
are present.
• Ground all equipment in the work area.
• Use only grounded hoses.
• If there is static sparking or you feel a shock, stop operation immediately. Do not
use equipment until you identify and correct the problem.
• Keep a fire extinguisher in the work area.
ELECTRIC SHOCK HAZARD
Improper grounding, setup, or usage of the system can cause electric shock.
• Turn off and disconnect power at main switch before disconnecting any cables and
before servicing equipment.
• Connect only to grounded power source.
• All electrical wiring must be done by a qualified electrician and comply with all local
codes and regulations.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in
the operating area of the equipment to help protect you from serious injury, including
eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes
but is not limited to:
• Protective eyewear
• Clothing and respirator as recommended by the fluid and solvent manufacturer
• Gloves
• Hearing protection
2
311305E
Warnings
WARNING
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the
eyes or on skin and cause serious injury.
• Follow Pressure Relief Procedure in this manual, when you stop dispensing and
before cleaning, checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest
rated system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS forms from
distributor or retailer.
• Check equipment daily. Repair or replace worn or damaged parts immediately with
genuine Graco replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your Graco distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and
hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To
avoid severe burns, do not touch hot fluid or equipment. Wait until equipment/fluid has
cooled completely.
311305E
3
Installation
Installation
3. Apply pipe sealant (not the supplied PVC
cement) to the threaded end of the suction
tube and then screw the tube into the pump
inlet port. Make sure tube is tight.
The oil transfer pumps are positive displacement pumps. The motors are drip proof rated
at 3/4 hp. The motors have sealed bearings
and require minimal maintenance. All models
come with hose, nozzle, 34 in. (864 mm) suction tube assembly, and bung adapter.
When unpacking check for shipping damage.
Report any shipping damage to delivering carrier immediately. See Parts, page 8.
Mounting Pump on Barrel or
Tank
1. Install bung adapter (14) in barrel bung and
tighten.
2. Assemble suction tube sections (18) by
applying PVC cement (21) to the inside
diameter of the PVC couplers (19, 20).
Make sure PVC cement is applied to the
complete inside diameter and slide the pipe
sections into the coupler with a twisting
motion.
4. Insert suction tube already attached to the
pump through bung adapter and lower the
pump onto the bung adapter. Position the
pump as desired and tighten swivel nut to
the bung adapter (14).
Mounting Hose and Nozzle
1. Before connecting hose to the pump, pour
8 oz (0.24 l) of oil in the pump outlet port so
that the pump does not run dry during initial
start-up.
2. Apply pipe sealant to male threads of the
elbow (12) and screw the elbow into the
outlet port.
3. Apply pipe sealant to one end of hose
assembly (17) and screw hose end into the
elbow (12).
4. Apply pipe sealant to other end of hose
assembly and screw the nozzle (15, 16)
onto the hose.
For tanks deeper than 36 in. (914 mm) you
will need a standard 1 in. (25 mm) pipe
with 1 in. npt threads on one end. If pumping used oil, install suction screen assembly, Part No. 260306, to filter large
contaminants.
For tanks less than 36 in. (914 mm) deep,
cut the suction tube to leave about 2 in. (21
mm) of clearance between the bottom of
the suction tube and the bottom of the
tank.
4
311305E
Operation
Electrical Installation
115 VAC and 230 VAC
Operation
CAUTION
Do not operate pump dry. Do not run pump for
more than 5 minutes with nozzle closed.
The 115 VAC models (260101 and 260102)
come wired with a short power cord and a
grounded electrical plug. Power to the unit
must be 115 VAC single phase. If an extension
cord is required, it should be a 3-wire cord with
a ground. Use a 20 amp circuit to supply power
to the pump.
The 230 VAC model (260104) is not shipped
with a power cord and plug. You must purchase and install an appropriate power cord
and plug that meets your local electrical codes.
Electrical Installation
12 VDC
The 12 VDC model (260100) is not shipped
with a power cord since the installation will
determine the length of the power cord.
See Parts, page 8 for items referenced in
parentheses, i.e., (17).
1. On/Off switch is located on the motor (9).
Move switch to ON position.
2. Insert nozzle into container or fill tube and
open nozzle to dispense fluid.
3. Close nozzle to stop flow. The pump has an
internal bypass valve that will bypass the
fluid internally with nozzle closed.
4. Immediately after dispensing, turn switch to
OFF position.
Pressure Relief Procedure
1. Verify the on/off switch is in the off position.
2. Remove the wiring junction box cover by
removing the four screws.
3. Use 10 AWG wire to connect the red (+)
and black (-) wires to the 12 VDC supply.
4. Reattach the wiring junction box cover with
the four screws.
311305E
1. Verify pump switch is OFF.
2. Open nozzle to relieve any residual pressure.
3. To prevent damage to the pump, use inlet
suction screen (260306) when pumping
used oils.
5
Troubleshooting
Troubleshooting
Problem
Motor runs but pump will not
prime.
Oil leaking in motor mount.
6
Cause
Solution
Motor rotation wrong.
Check wiring instructions for
(260100 only)
possible problems.
Dirt under pressure relief valve. Remove pressure relief valve
and inspect, clean, or replace if
damaged.
Worn or damaged gears.
Remove cover and inspect
gears. Replace if worn or damaged.
Oil level low.
Refill tank.
Cover seal (5) damaged.
Replace if worn or damaged.
Inlet suction screen clogged
Remove and clean or replace.
(used oil).
Air leak in suction tube.
Inspect all joints in suction
tube, make sure all threaded
joints have sealant applied.
Air lock in system.
This may occur if filter or meter
or automatic shut-off nozzle is
used. If this occurs, fill pump
and meter with fluid through
top of pump.
Motor does not run at proper
Check electric connections.
speed.
Ensure supply voltage is at
proper level.
Faulty or damaged motor shaft Replace shaft seal (4).
seal.
Operating pump extended time Do not exceed 5 minutes of
with nozzle closed.
operation with nozzle closed.
Motor shaft worn.
Replace motor if shaft has
groove worn in seal area.
311305E
Troubleshooting
Problem
Unit pumps but output flow is
low.
Motor stalls when nozzle is
closed.
Motor overheating.
Switch will not turn pump on.
311305E
Cause
Clogged inlet suction screen
(used oil).
Air leak in suction tube.
Solution
Clean or replace.
Check to make sure all joints in
suction tube are sealed.
Suction tube too close to tank Suction tube must have a 2 in.
bottom.
(51 mm) minimum clearance.
Tank empty.
Refill tank.
Tank not vented.
Tank must be vented to atmosphere.
Worn or damaged gears.
Remove cover and inspect
gears. Replace if worn or damaged.
Damaged motor.
Replace motor.
Clogged suction tube, hose, or Inspect and clean.
nozzle.
Bypass relief valve is stuck.
Inspect relief valve, making
sure ball is free. Replace if
damaged.
Low supply voltage.
Check supply voltage.
Gears damaged and binding. Inspect gears. Gears should
turn freely. Replace if damaged.
Faulty motor.
Replace motor.
Gears binding.
Check to make sure gears turn
freely on shaft.
Operating pump extended time Do not exceed 5 minutes of
with nozzle closed.
operation with nozzle closed.
Clogged inlet suction screen. Clean or replace.
Clogged suction tube, hose, or Inspect and clean if required.
nozzle.
Operating pump more than 30 Limit operation to 30 minutes
minutes continuous duty.
per hour.
Blown fuse or circuit breaker. Check electrical supply.
Electrical problem.
Check that supply voltage is
proper and getting to pump.
Defective switch.
Check and replace motor (9) if
defective.
Damaged or defective motor. Check motor, replace if damaged or defective.
7
Parts
Parts
Model 260100, 12 VDC
Model 260101, 115 VAC
Model 260102, 115 VAC
Model 260104, 230 VAC
9
13
4
12
1
5
8
7
10
11
3
2
14
6
21
18
20
16
15
17
19
8
311305E
Parts
Ref.
No.
1
2
3
4
5
6
7
8
9a
9b
9c
9d
Description
PUMP BODY
ADAPTER, pump motor
GEAR, pump
SEAL, shaft
O-RING
SCREW, 3/8-16 socket head, cap
BALL, relief valve
PIN, dowel, steel, 3/8 x 3/4
MOTOR, 115 VAC
MOTOR, 115 VAC, 8 gpm
MOTOR, 12 VDC
MOTOR, 230 VAC (This model does
Qty.
1
1
2
1
1
4
1
1
1
1
1
not include power cord and plug. Must be
purchased separately.)
10a SPRING, relief valve
115 VAC, 12 VDC
10b SPRING, relief valve
115 VAC, 8 gpm
11 PLUG, 1/2 npt
1
Ref.
No.
12
13
14
15
16
17
18
19
20
21
22▲
Description
ELBOW, street, 3/4 npt
SCREW, cap, 5/16-18
ADAPTER, bung
NOZZLE
VALVE, ball
HOSE, petroleum
PIPE, PVC
COUPLER, PVC, female
ADAPTER, PVC male
CEMENT, PVC
LABEL, warning (not shown)
Part no. 15G901
Qty.
1
4
1
1
1
1
2
1
1
1
1
▲ Replacement Danger and Warning labels,
tags, and cards are available at no cost.
1
Kits
Kit
Number
260040
260061
260125
260216
260292
260293
260297
260298
260300
260495
260496
260497
260498
260500
260499
311305E
Description
ELBOW, street, 3/4npt
ADAPTER, bung
KIT, valve
HOSE, 8 ft
KIT, packing
KIT, gear
KIT, pressure relief
(models 260100, 260101, and 260104)
KIT, pressure relief
(model 260102)
KIT, suction pipe
KIT, fluid, 115 VAC, 230 VAC, 12 VDC
(models 260100, 260101, and 260104)
KIT, fluid, 115 VAC, 8 gpm
(model 260102)
KIT, motor, 115 VAC
KIT, motor, 115 VAC, 8 gpm
KIT, motor, 12 VDC
KIT, motor, 230 VAC
Includes Items
12
14
15, 16
17
4, 5
3, 4, 5
7, 10a, 11
7, 10b, 11
18, 19, 20, 21
1, 2, 3, 4, 5, 7, 8, 10a, 11,
13
1, 2, 3, 4, 5, 7, 8, 10b, 11,
13
9a
9b
9c
9d
9
Technical Data
Technical Data
Maximum Working Pressure
Automatic Relief Setting
65 psi (0.45 MPa, 4.5 bar)
Models 260100, 260101, 260104:
65 psi (0.45 MPa, 4.5 bar)
Model 260102:
30 psi (0.21 MPa, 2.1 bar)
Output Flow
Model 260100: 5.8 gpm (22.0 lpm)
Model 260101: 4.25 gpm (16.15 lpm)
Model 260102*: 8.0 gpm (30.3 lpm)
Model 260104: 4.25 gpm (16.15 lpm)
Inlet Size
1 in. npt
Outlet Size
3/4 in. npt
Weight
Model 260100: 34 lb (15.3 kg)
Models 260101, 260102, 260104:
25 lb (11.25 kg)
Dimensions
See page 11
Voltage/current
Model 260100: 12 VDC, 35 amps
Models 260101, 260102:
115 VAC, 60 Hz, 9.2 amps
Model 260104: 230 VAC, 50/60 Hz, 4 amps
Power Cord
Model 260101, 260102 only: 30 in. (762 mm)
Hose size
8 ft (2.4 m), 3/4 in. (19 mm) ID
Suction tube
34 in. (864 mm)
Wetted parts
carbon steel with zinc plating, stainless steel,
galvanized steel, aluminum, nitrile, rubber, PVC,
PVC cement
*Model 260102 is intended for use with fluid viscosities of 1000 centistokes (5000 ssu) or less.
For fluids with viscosities greater than 1000 centistokes use pump model 260101.
10
311305E
Technical Data
Dimensions
A
B
C
Models
260100
260101
260102
260104
311305E
Length (A)
Inches
mm
13.25
336.5
12.5
317.5
12.75
323.8
13.75
349.2
Height (B)
Inches
mm
8
203.2
8
203.2
8
203.2
8
203.2
Width (C)
Inches
mm
7.75
196.8
6.75
171.4
6.25
158.7
6.5
165.1
11
Technical Data
Performance Chart
฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀
฀
฀฀฀฀฀฀฀฀฀
฀฀฀฀฀฀฀฀฀
฀
฀฀฀฀฀฀฀฀฀
฀
฀฀฀฀฀฀฀฀฀
฀ ฀
฀ ฀
฀
฀
฀
฀
฀
฀
฀
฀
฀
฀
฀ ฀
฀ ฀
฀
฀
฀
฀
฀
฀
฀ ฀
12
311305E
Notes
Notes
311305E
13
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents.
Original instructions. This manual contains English. MM 311305
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2005, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised August 2012
Download PDF